DI 450
Dishwasher
Installation and use
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Is a Good Habit to Get Into
NOTICE
- If the appliance is not operating properly or maintenance
must be performed, disconnect the appliance from the power
supply.
5.Keep detergents out of the reach of children, who must
also be kept away from the dishwasher when it is open.
6.This appliance cannot be installed outdoors, not even if
the area in which it is installed is covered by a roof; it is also
very dangerous to leave it exposed to the rain and elements.
7.Do not touch the heating element during or after a wash
cycle.
Carefully read the instructions contained in this manual, as
they provide important information which is essential to
safe and proper installation, use and maintenance of the
appliance.
This appliance complies w ith the follow ing EEC
directives:
- 73/ 23/ EEC (Lo w Vo lt a g e ) a n d su b se q u e n t
modifications;
- 89/336/EEC (Electromagnetic Compatibility) and
subsequent modifications.
- 97/17/EEC (Labelling)
1.Carefully dispose of the packing material.
2.After removing the packing, check to make sure that
the appliance is not damaged. If in doubt, contact a
qualified professional.
3.The dishwasher must only be used by adults for the
washing of household dishes and cooking utensils.
4.Fundamental rules to follow when using the appliance:
- Never touch the dishwasher when barefoot or with wet
hands or feet;
- We discourage the use of extension cords and multiple
sockets;
- During installation, the power supply cord must not be
excessively or dangerously bent or flattened;
8.Do not lean or sit on the door when it is open, as this could
overturn the dishwasher.
9.If the appliance malfunctions, turn off water supply to the
appliance and disconnect the plug from the wall socket.
Then, consult the section entitled, "Troubleshooting." If you
cannot resolve the problem, contact a service centre.
10.Appliances which are no longer being used must be made
inoperable by cutting the power supply cord and removing
the door lock.
To maintain the EFFICIENCY and SAFETY of this
appliance, w e recommend:
l call only the Service Centers authorized
by the manufacturer
l alw ays use original Spare Parts
Close-up View (control panel)
E
B
A
G
P
S
1
2
3
4
5
1
2
3
4
5
eco
ON-OFF Button
ON - OFF Light
Cycles Indicator Lights
Cycle select button
P
Low salt indicator light
GB
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Close-up View (Interior)
E
G
F
H
J
I
K
L
Bottom Sprayer Arm
Salt Container Cap
Upper Rack
Top Sprayer Arm
Rack Height Adjustor
Low er Rack
Washing Filter
Detergent and Rinse Aid Dispenser
Technical characteristics
Width
cm. 44,5
Depth
cm. 57
cm. 82-90
Height
Capacity
9 standard place settings
4.3psi - 145psi 30 KPa÷ 1MPa (0,3 ÷10 bar)
See data plate
Mains water pressure
Power voltage
Total absorber power
Fuse
See data plate
See data plate
GB
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Salt .......
Salt
Adjusting Salt Consumption
The hardness of the water varies from place to place. If
hard water is used in the dishwasher, deposits will form on
the dishes and utensils.
The dishwasher is designed to allow for adjusting the amount
of salt consumed based on the
harness of the water used. This
The appliance is equipped with a special softener that uses
a salt specifically designed to eliminate lime and minerals
from the water.
is intended to optimize and cus-
tomize the level of salt con-
sumption so that it remains at a
minimum.
Your Local Water Board can
supply the degree of hardness
of the water
Loading the Salt into the Softener
Always use salt intended for use with dishwashers.
The salt container is
located beneath the lower
in your area.
rack and should be filled
To adjust salt consumption, pro-
as follows:
ceed as follows:
1. Remove the lower rack
and then unscrew and
remove the cap from the
salt container;
2. If you are filling the
container for the first time,
fill it with water;
1) Unscrew the cap from the salt container.
2) There is a ring on the container with an arrow on it (see
figure to the side), if necessary, rotate the ring in the anti-
clockwise direction from the "_" setting towards the " +"
sign, based on the hardness of the water being used.
It is recommended that adjustments be made in accord-
ance with the following schema:
3. Place the end of the
funnel (supplied) into the
hole and introduce about
2 kg of salt. It is normal for a small amount of water to
come out of the salt container.
4. Carefully screw the cap back on.
Water Hardness
Salt
Autono-
consu-
Clarke
degrees
Selector
position
my
°fH
mmol/l
mption
(grams/-
cycle)
The salt container should be filled up when the low salt
indicator light "E" flashes. Once you have loaded the salt for
the first time, it is normal that the low salt indicator light
stays on or flashes for about 5 consecutive cycles.
(cycles\2-
kg)
0 - 14
0 - 17
0 -1,7
/
0
/
To prevent the formation of rust, load the salt just before
beginning a wash cycle.
14 - 36 18 - 44 1,8 - 4,4
36 - 71 45 - 89 4,5 - 8,9
"-"
20
40
60
60
40
25
MED
"+"
>71
> 89
> 8,9
GB
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Detergent and Rinse Aid ....
Detergent
Rinse Aid
Detergent specifically intended for use with dishwashers
must be used. The dispenser must be refilled before the
start of each wash cycle following the instructions provided
in the " Wash Cycle Table." The detergent dispenser is
located on the inside panel of the door.
This product makes dishes sparkle more as it improves their
drying. The rinse aid container is situated on the inside of the
appliance door; you should refill it when you see the container
is empty by means of indicator “D”.
(If your dishwasher is fitted with a “low rinse aid” indicator
light, fill the container up when the indicator light flashes or
lights up).
Loading the detergent
To open lid "A", press button "B". The cleaning detergent
should be introduced into the two containers "C"and "D"
up to the rim.
After pouring in the detergent, replace the lid, pressing
down until it clicks.
Loading the Rinse Aid
To open the dispenser, turn the "C" cap in the anti-clockwise
direction and then pour in the rinse aid, making sure not to
overfill. The amount of rinse aid used for each cycle can be
regulated by turning the "F" dose adjustor, located beneath
the " C" cap, with a screwdriver. There are 6 different
settings; the normal dosage setting is 4.
Dishwasher detergent in tablets is now available on the
market, in which case you should place one tablet into
container " D" and replace the lid.
B
C
D
F
C
24 gr
.
3 gr.
D
Important:
Proper dosage of the rinse aid improves drying.
If drops of water remain on the dishes or spotting occurs,
the dosage adjustor should be turned to a higher setting. If
the dishes have white streaks, turn the dosage adjustor to a
lower setting.
A
Notice: To facilitate closing the cover, remove any
excess detergent on the edges of the dispenser.
Warning
Three-in-one dishwasher tablets are now available on the market, and combine the detergent, salt and rinse aid all in one.
If the water in your area is hard or very hard, we still recommend you pour extra salt into the relevant dispenser to prevent the
formation of white streaks on your dishes or on the appliance interior.
Add rinse aid to the corresponding container only if you are dissatisfied with the results on your dishes.
In any case, please read the manufacturer's instructions provided on the packet.
If you use only these products, it is normal for the salt and rinse aid indicator lights to flash permanently after a certain
number of cycles.
GB
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading the Dishw asher
Before placing the dishes in the dishwasher, remove the
larger food particles to prevent the filter from becoming
clogged, which results in reduced performance.
If the pots and pans have baked-on food that is extremely
hard to remove, we recommend that they be allowed to
soak before they are washed. This will eliminate the need
for extra wash cycles.
Upper Rack
Low er Rack
Pull out the racks to facilitate loading the dishwasher.
How to Use the Low er Rack
We recommend that you place the most difficult to clean
items on the bottom rack: pots, pans, lids, serving dishes
and bowls, as shown in the figure to the right.
It is preferable to place serving dishes and lids on the
sides of the racks in order to avoid blocking the rotation
of the top spray arm.
- Pots, serving bowls, etc. must always be placed top
down.
- Deep pots should be slanted to allow the water to flow
out.
- Silverware should be placed in the silverware basket.
insert the cutlery into the basket: knives and utensils with
sharp blades or tips should be positioned with the sharp
parts at the bottom.
- If the rack has side baskets, the spoons should be loaded
individually into the appropriate slots.
Position all cutlery items so that they don't touch.
- Especially long utensils should be placed in the
horizontal position at the front of the upper rack.
How to Use the Upper Rack
The upper rack is designed to hold more delicate and
lighter dishware, such as glasses, coffee and tea cups
and saucers, as well as plates, small bowls and shallow
pans (as long as they are not too dirty).
Fig. A
- Position the dishes and cookware so that they do not
get moved by the spray of water.
How to adjust the Upper rack ...
The top rack can be adjusted using the two rack heights
(top and bottom). To adjust the rack, open up the tabs
that lock the guides and pull out the rack. Arrange the
rack with the back wheels in either the top or bottom
position and then insert it along the guides until the front
wheels are on as well. Close the tabs to lock the rack in
place (see Fig. F)
1
2
4
3
Fig. F
GB
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Starting the Appliance
Starting a w ash cycle....
There's been a pow er failure? Have you opened the
dishw asher door?
The wash cycle stops and then restarts when the electricity
comes back on or when you close the door.
After performing all the operations described in the previous
paragraphs, turn the water tap on completely, open the
appliance door and press ON-OFF button "A": indicator light
" B" comes on. Your appliance is now on and awaiting
instructions.
At the end of the w ash cycle...
The end of the wash cycle is indicated by a double beep and
the flashing of the wash cycle indicator light " G". Open the
dishwasher door, press the ON-OFF button as well, thus
cutting off the electricity supply to the appliance.
Turn off the water tap.
Wait a few minutes before unloading the dishes: they are
very hot! If you wait a little while, they dry better thanks to
the steam.
Setting and Starting a Wash Cycle
Select the wash cycle by pressing button "P". Each time this
button is pressed, one of the indicator lights " G" will come
on in sequence, select the wash cycle you deem most
suitable for the type of dishes to wash (take a look at page
7, where you will find the wash cycle table). Close the
appliance door and after a few seconds, you will hear a
short beep: the wash cycle has begun.
Empty the lower rack first.
Cancelling or modifying a cycle w hile underw ay...
Premise: A cycle that is underway can only be modified if it
has only been running for a short time.
Make sure the wash cycle has ended before removing the
dishes!
Open the appliance door carefully to avoid any hot water
splashes, then keep button " P" pressed for approximately 5
seconds, until you hear 3 short beeps. Indicator light " G"
will come off and at this point, all the settings will have
been cancelled. You are now free to re-set the correct wash
cycle.
Warning
If opening the door soon after the end of the programme,or
during it, stand away from the Dishwasher, to avoid possible
injury from hot steam.
If you forget to load some of the dishes...
Interrupt the wash cycle by opening the appliance door with
the utmost care, as usual, then insert the dish you had
forgotten. When you shut the appliance door, the cycle will
start up from where you interrupted it. restart at the point
where it left off.
GB
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Wash Cycle Table
Dishw asher w ashing guarantees your dishes w ill be cleaned in a hygienic setting for
safer, cleaner results.
:DV K
F\FOH
GXUDWLRQ
ꢃWROHUDQFH
“ꢄꢅꢆꢀꢇ
'HWHUJHQW
IRU
SUHꢁZDVK
ꢂꢀZDVK
&\FOHꢀVHOHFWLRQ
LQVWUXFWLRQV
5LQVH
$LG
&\FOH
&\FOHꢀGHVFULSWLRQ
3UHꢅZDVKꢀZLWKꢀKRWꢀZDWHUꢀDWꢀꢆꢇƒ&
:DVKꢀDWꢀꢈꢉƒ&ꢄ
ꢊꢀ5LQVHVꢀZLWKꢀFROGꢀZDWHU
5LQVHꢀZLWKꢀKRWꢀZDWHUꢀDWꢀꢈꢉƒ&ꢄ
'U\LQJꢄ
9HU\ꢀGLUW\ꢀGLVKHVꢁ
SRWVꢀDQGꢀSDQVꢀꢂQRWꢀWR
EHꢀXVHGꢀZLWKꢀGHOLFDWH
LWHPVꢃꢄ
ꢄꢉꢅꢍ
ꢏꢈꢍ
ꢈꢂꢉꢊꢀJUꢋ
ꢉꢎꢀJUꢋ
ꢌ
ꢌ
ꢄꢇꢀ,QWHQVLYH
ꢉꢇꢀ7LPHꢊ<RX
ꢈꢇꢀ(FR
1RUPDOO\ꢀGLUW\
GLVKHVꢁꢀSRWVꢀDQG
SDQVꢄꢀ6WDQGDUGꢀGDLO\
F\FOHꢄ
:DVKꢀDWꢀꢀꢈꢇƒ&ꢄ
5LQVHꢀZLWKꢀFROGꢀZDWHU
5LQVHꢀZLWKꢀKRWꢀZDWHUꢀDWꢀꢋꢇƒ&ꢄ
'U\LQJꢄ
(QYLURQPHQWDOO\ꢅIULHQꢅ
GO\ꢀF\FOHꢁꢀZLWKꢀORZ
HQHUJ\ꢀFRQVXPSWLRQ
OHYHOVꢁꢀVXLWDEOHꢀIRU
QRUPDOO\ꢀGLUW\ꢀSDQV
DQGꢀGLVKHVꢄ
ꢊꢀ&ROGꢀSUHꢅZDVKHV
:DVKꢀDWꢀꢉꢇƒ&
+RWꢀULQVHꢀDWꢀꢈꢉƒ&
'U\LQJ
ꢈꢂꢉꢊꢀJ
ꢄꢊꢐꢍ
ꢊꢅꢍ
ꢌ
ꢌ
(FRQRPLFꢀDQGꢀIDVW
F\FOHꢀWRꢀEHꢀXVHGꢀIRU
VOLJKWO\ꢀGLUW\ꢀGLVKHVꢄ
5XQꢀF\FOH
6KRUWꢀZDVKꢀDWꢀꢆꢋƒ&
+RWꢀULQVHꢀDWꢀꢈꢉƒ&
'U\LQJ
ꢉꢅꢀJ
LPPHGLDWHO\ꢀDIWHUꢀXVHꢄ
ꢊꢇꢀ5DSLGꢀ
'U\
3UHꢅZDVKꢀRIꢀGLVKHVꢁ
SRWVꢀDQGꢀSDQVꢀZKLOH
ZDLWLQJꢀIRUꢀWKHꢀORDG
WRꢀEHꢀFRPSOHWHGꢀDIWHU
WKHꢀVXEVHTXHQWꢀPHDOꢄ
6KRUWꢀFROGꢀZDVKꢀWRꢀSUHYHQWꢀIRRG
UHVLGXHꢀIURPꢀGU\LQJꢀRQꢀWKHꢀGLVKHVꢄ
ꢄꢉꢍ
ꢐꢇꢀ6RDN
GB
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Energy Saving Tips
- It is important to try and run the dishwasher when it is fully
loaded in order to save on energy. In order to prevent odors
from forming and food from caking onto the dishes, you
can run the hold cycle.
- Use the right amount of detergent: if you use too much
detergent, the result will not be cleaner dishes, but, rather,
a greater negative impact on the environment.
- There is no utility in rinsing dishes, cookware and utensils
before placing them in the dishwasher.
- Choose the right wash cycle: the choice of cycle depends
on the type of dishware, cookware and utensils being
washed and how dirty they are.
How to Keep Your Dishw asher in Shape
After Every Wash
When You Go on Holiday
After every wash, turn off the water supply to the appliance
and leave the door slightly ajar so that moisture and odors
are not trapped inside.
When you go on holiday, it is recommended that you run a
wash cycle with the dishwasher empty and then remove
the plug from the socket, turn off the water supply and
leave the door of the appliance slightly ajar. This will help
the seals last longer and prevent odors from forming within
the appliance.
Remove the Plug
Before cleaning or performing maintenance, always remove
the plug from the socket. Do not run risks.
Moving the Appliance
No Solvents or Abrasive Cleaning Products
If the appliance must be moved, try to keep it in the vertical
position. If absolutely necessary, it can be positioned on its
back.
To clean the exterior and rubber parts of the dishwasher, do
not use solvents or abrasive cleaning products. Rather, use
only a cloth and warm soapy water.
To remove spots or stains from the surface of the interior,
use a cloth dampened with water and a little white vinegar,
or a cleaning product made specifically for dishwashers.
Seals
One of the factors that cause odors to form in the dishwasher
is food that remains trapped in the seals. Periodic cleaning
with a damp sponge will prevent this from occuring.
GB
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and Special Maintenance
The filter assembly
1
If you want consistent good results from your dishwasher,
you need to clean the filter assembly.
A
B
2
The food particles are removed from the wash water,
allowing it to be recirculated during the cycle, filtered
perfectly. For this reason, it is a good idea to remove the
larger food particles trapped inside the cup “C” and the
semi-circular filter A after each wash; pull the cup handle
upwards to remove them. Just rinse them under running
water.
The entire filter assembly should be cleaned thoroughly once
a month: cup C + semi-circular filter A + cylindrical filter B.
Rotate filter “B” anticlockwise to remove it.
C
Cleaning the Sprayer Arms
It may happen that food particles become encrusted on the
sprayer arms and block the holes. Check the sprayer arms
periodically and clean them when needed (see “Close-up
View [interior]”, letters F-I).
For cleaning, use a non metallic brush.
Cleaning the Water Inlet Filter
Reassemble the filter parts (as shown in the figure) and
reinsert the whole assembly into the dishwasher. Position it
into its housing and press downwards.
The dishwasher is not to be used without filters. Improper
replacement of the filters may reduce the efficiency of the
wash and even damage your dishwasher.
Periodically clean the water inlet filter (see figure 2 under
"Installation") located on the outlet of the water supply tap.
After turning off the water tap, unscrew the end of the water
supply hose, remove the filter and clean it carefully under
running water. Then, return the filter to its place and tighten
the water supply hose back into position.
Troubleshooting
It may occur that the dishwasher does not function or does
not function properly. Before calling for assistance, let us
see what can be done first: have you forgot to press one of
the buttons or to perform an essential operation?
The Dishw asher Does Not Start
Have you checked whether:
- the plug is pushed into the socket correctly;
- the power is on in the house;
- the door is closed properly;
- the ON-OFF switch is on " ON" ;
- the water supply is turned on.
The Dishw asher Does Not Load Water
Have you checked whether:
- the water is turned on and the hose is connected properly;
- the water supply to the house is on and has sufficient
pressure;
- the water supply hose is crimped or bent;
- the filter for the water supply hose is clogged.
The Dishes Are Not Clean
Take a note of which lights are flashing, turn the appliance off and
call for technical assistance.
Tap off alarm
If you have forgotten to turn the water tap on, your appliance will
remind you of this by sounding a few short beeps for a few minutes.
Turn the tap on and your appliance will start up again after a few
minutes. Were you to be absent when these beeps are sounded, the
appliance will be blocked automatically and indicator lights 3 and 4
Eco and Rapid) will flash rapidly. Turn the appliance off at the ON-
OFF button, turn on the water tap and wait approximately 20
seconds before turning the appliance back on; repeat the
programming operations and the selected wash cycle will start up
again.
Clogged filter alarm
If the appliance is blocked and indicator lights 2 normal) and 4
(Rapid) flash rapidly, this means the filter is clogged by large particles
of food residue. Turn the appliance off, clean the filter thoroughly
and reposition it in its seat as illustrated on this page. Then turn it
back on. Repeat the programming operations and the selected wash
cycle will start up again.
Water load solenoid valve malfunction alarm.
If indicator light 3 (Eco) flashes rapidly, TURN the dishwasher OFF
AND BACK ON AGAIN after one minute. If the alarm persists, first
turn off the water tap to avoid any flooding and then cut off the
electricity supply and call for technical assistance.
Have you put the right amount of detergent into the
dispenser?
Is the wash cycle suitable for the dishes you have placed
inside the appliance?
Are the filter and microfilter clean?
Can the sprayer arms turn freely?
The Dishw asher Does Not Drain
Have you checked whether:
If, despite all these checks, the dishwasher still does not
function and/or the problem persists, contact the nearest
authorised service centre and provide them with the
following information:
- the drain hose is crimped or bent.
- the nature of the problem;
Lime Deposits or a White Film Form on the Dishes
Have you checked whether:
- the lid to the salt container is closed properly;
- the rinse aid dosage is correct.
Error messages.
Your dishwasher is equipped with a safety system which is able to
detect any operating anomalies. These anomalies are reported by
one or two wash cycle indicator lights "G" flashing rapidly.
- the model type number (Mod. ...) and the serial number
(S/N ....), which are indicated on the plate located on the
side of the inner part of the door.
Never call on unauthorised technicians and refuse to
allow parts to be installed that are not original spare
parts.
GB
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Drain Hose Connection
Positioning the Appliance
Fit the drain pipe into a drain
line with a minimum diameter
of 4 cm or place it over the
sink. Avoid restricting or
bending it. The part of the pipe
marked with the letter A
should be between 40 and 100
cm above the ground.
Position the appliance in the desired location. The back
should rest against the wall behind it, and the sides, along
the adjacent cabinets or wall. The dishwasher is equipped
with water supply and drain hoses that can be positioned to
the right or the left to facilitate proper installation.
A
Levelling the Appliance
Once the appliance is positioned, adjust the feet (screwing
them in or out) to adjust the height of the dishwasher, making
it level. In any case, the appliance should not be inclined
more than 2°.
The pipe should not be
immersed in water.
If the appliance is level, it will help ensure proper perfor-
mance.
Electrical Connection
After making sure that the voltage and frequency values for
the current in the home correspond to those on the rating
plate (located on the stainless steel inner door of the
appliance) and that the electrical system is sized for the
maximum voltage on the rating plate, insert the plug into
an electrical socket which is earthed properly (the earthing
of the appliance is a safety requirement mandated by law).
If the electrical socket to which the appliance must be
connected is not appropriate for the plug, replace the plug,
rather than using adpators or the like as they could cause
overheating and burns.
Cold Water Connection
This electric household appliance should be connected to
the water mains using the cold water supply hose provided
with the appliance only. Do not
use a different hose. In the event
of replacements, use original
spare parts only.
Connect the cold water supply
hose to a threaded 3/4 (gas)
connector, inserting the small
A
filter supplied with the
dishwasher and making sure
that it is fastened tightly in place
Caution: the dishwasher plug must be accessible even when
the appliance is installed as a built-in unit so that maintenance
can be done safely.
Fig.2
(see figure 2).
If the water pipes are new or have not been used for an
extended period of time, let the water run to make sure that
the water is clear and free of impurities. If this precaution is
not taken, there is a risk that the water inlet can get blocked
and damage the appliance.
Should the electricity supply cable be damaged, we
recommend that you only contact authorised Technical Service
Centres for the replacement.
Condensation-proof tape.
On some models, a transparent condensation-proof adhesive
tape has been provided.
It should be stuck onto the lower side of your wooden worktop
to protect it from the formation of condensation.
When not provided, this tape can be requested as a spare
part from authorised retailers.
Hot Water Connection
The water supply to the appliance can also be connected to
the house's hot water line (centralised system, heating
system), as long as it does not exceed a temperature of
60°C.
In this case, the wash cycle time will be shortened by about
15 minutes and the wash efficiency slightly reduced.
The connection must be made to the hot water line following
the same procedures as those for the connection to the cold
water line.
GB
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connection
Electrical Connection
As the colours of the wires in the mains lead may not
correspond with the coloured markings identifying the
terminal in your plug, proceed as follows:
connect Green & Yellow wire to terminal market “E” or
coloured Green or Green & Yellow.
If your appliance is supplied with a 13 amp. fused plug it
can be plugged into a 13 amp socket for immediate use.
Before using the appliance please read the instruction below.
WARNING: THIS APPLIANCE MUST BE EARTHED.
THE FOLLOWING OPERATIONS SHOULD BE CARRIED OUT
BY A QUALIFIED ELECTRICIAN.
Connect Brown wire to terminal marked “L” or coloured
Red.
Connect Blue wire to terminal marked “N” or coloured
Black.
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA approved
fuse to BS 1362 should always be used, and the fuse cover
re-fitted. If the fuse cover is lost, the plug must not be used
until a replacement is obtained.
If a 13 amp plug (BS 1363) is used it must be fitted with a
13 amp fuse. A15 amp plug must be protected by a 15
amp fuse, either in the plug or adaptor or at the
distribution board.
If you are in any doubt about the electrical supply to your
machine, consult a qualified electrician before use.
Replacemente fuse covers:
If a replacement fuse cover is fitted, it must be of the correct
colours as indicated by the coloured marking or the colour
that is embossed in words on the base of the plug.
Replacements can be obtained directly from your nearest
Service Depot.
How to connect an alternative plug:
The wires in this mains lead are coloured in accordance
with the following code:
Removing the plug:
BLUE
BROWN
GREEN AND YELLOW
“NEUTRAL” (“N”)
“LIVE” (“L”)
“EARTH” (“E”)
Ifyour appliance has a non-rewireable moulded plug and
you should wish to remove it to re-route the mains cable
through partitions, units etc., please esure that either:
- the plug is replaced by a fused 13 amp re-wireable plug
bearing the BSI mark of approval
- or:
GREEN &
YELLOW
- the mains cable is wired directly into a 13 amp cable outlet,
controlled by a switch, (in compliance with BS 5733) which
is accessible without moving the appliance.
13 amp fuse
BROWN
BLUE
Disposing of the plug:
CROSS-BAR
CORD GRIP
Ensure that before disposing of the plug itself, you make
the pins unusable so that it cannot be accidentally inserted
into a socket.
Instruction for connecting cable to an altenative plug:
Important: the wires in the mains lead are coloured in
accordance with the following code:
Green & Yellow
Blue
Brown
- Earth
- Neutral
- Live
Disposing of the appliance:
When disposing of the appliance please remove the plug
by cutting the mains cable as close as possible to the plug
body and dispose of it as described above
CAUTION:
The dishwasher plug must be accessible even when the
appliance is installed as a built-in unit so that maintenance
can be done safely.
GB
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Merloni Elettrodomestici
Viale Aristide Merloni 47
60044 Fabriano
Italy
Tel +39 0732 6611
Fax +39 0732 662501
Download from Www.Somanuals.com. All Manuals Search And Download.
|