CONNECTED NAVIGATION SYSTEM
DNN9150BT
DNN9150BTM
CONNECTED MONITOR WITH DVD RECEIVER
DNR8015BT
DNR8015BTM
Quick Start Guide
You can update the system by connecting a USB device containing an
update file.
For updating the system, visit <http://www.kenwood.com/cs/ce/>.
© 2014 JVC KENWOOD Corporation
B5K-0079-00 (MN/M2N/XN)
Download from Www.Somanuals.com. All Manuals Search And Download.
ÑPrecautions on handling discs
Precautions
•
•
Do not touch the recording surface of the disc.
Do not stick tape etc. on the disc, or use a disc
with tape stuck on it.
2WARNING
ÑTo prevent injury or fire, take the following
precautions:
•
•
Do not use disc type accessories.
Clean from the center of the disc and move
outward.
•
•
•
To prevent a short circuit, never put or leave any
metallic objects (such as coins or metal tools)
inside the unit.
Do not watch or fix your eyes on the unit’s
display when you are driving for any extended
period.
•
•
When removing discs from this unit, pull them
out horizontally.
If the disc center hole or outside rim has burrs,
use the disc only after removing the burrs with a
ballpoint pen etc.
•
Discs that are not round cannot be used.
If you experience problems during installation,
consult your Kenwood dealer.
ÑPrecautions on using this unit
•
•
•
When you purchase optional accessories, check
with your Kenwood dealer to make sure that they
work with your model and in your area.
You can select language to display menus, audio
file tags, etc. See Language setup (P.110) in
the Instruction Manual.
The Radio Data System or Radio Broadcast Data
System feature won’t work where the service is
not supported by any broadcasting station.
•
•
8-cm (3 inch) discs cannot be used.
Discs with coloring on the recording surface or
discs that are dirty cannot be used.
This unit can only play the CDs with
•
.
This unit may not correctly play discs which do
not have the mark.
You cannot play a disc that has not been
finalized. (For the finalization process see your
writing software, and your recorder instruction
manual.)
ÑProtecting the monitor
•
To protect the monitor from damage, do not
operate the monitor using a ballpoint pen or
similar tool with the sharp tip.
ÑLens fogging
ÑErase the personal information
Before giving or selling this unit to others, be sure
to delete the information (mail, search logs, etc.)
stored in this unit by yourself and confirm that the
data has been deleted.
We shall not be liable for any damage caused by
leakage of undeleted data.
1. Press the <HOME> button.
When you turn on the car heater in cold weather,
dew or condensation may form on the lens in the
disc player of the unit. Called lens fogging, this
condensation on the lens may not allow discs to
play. In such a situation, remove the disc and wait
for the condensation to evaporate. If the unit still
does not operate normally after a while, consult
your Kenwood dealer.
2. Press the <MENU> button.
3. Touch [Setting].
4. Touch [Backup & Reset].
5. Touch [Factory data reset].
6. Enter owner password. Touch [Reset].
7. Touch [ERASE].
Download from Www.Somanuals.com. All Manuals Search And DownlEoandg. lish ñ 3
ÑAcquiring GPS signal
ÑHow to reset your unit
If the unit or the connected unit fails to operate
properly, reset the unit.
(DNN9150BT/ DNN9150BTM)
The first time you turn on this unit, you must wait
while the system acquires satellite signals for the
first time. This process could take up to several
minutes. Make sure your vehicle is outdoors in an
open area away from tall buildings and trees for
fastest acquisition.
1Press the <Reset> button.
The unit returns to factory settings.
DNR8015BT/
DNR8015BTM
After the system acquires satellites for the first time,
it will acquire satellites quickly each time thereafter.
ÑAbout the front panel
When removing the product from the box or
installing it, the front panel may be positioned
at the angle shown in (Fig. 1). This is due to the
characteristics of mechanism the product is
equipped with.
When the product is first powered on works
properly, the front panel will automatically move
into the position (initial setting angle) shown in
(Fig. 2).
✎ NOTE
•
Disconnect the USB device before pressing the
<Reset> button. Pressing the <Reset> button with
the USB device connected can damage the data
stored in the USB device. For how to disconnect the
•
When the unit is turned on after resetting, the Initial
(Fig. 1)
(Fig. 2)
ÑCleaning the Unit
If the faceplate of this unit is stained, wipe it with a
dry soft cloth such as a silicon cloth. If the faceplate
is stained badly, wipe the stain off with a cloth
moistened with neutral cleaner, then wipe it again
with a clean soft dry cloth.
!CAUTION
•
Applying spray cleaner directly to the unit may
affect its mechanical parts. Wiping the faceplate
with a hard cloth or using a volatile liquid such as
thinner or alcohol may scratch the surface or erase
screened print.
4 ñ EngDlisohwnload from Www.Somanuals.com. All Manuals Search And Download.
2CAUTIONS
Safety Precautions and
Important Information
Failure to avoid the following potentially
hazardous situations may result in injury or
property damage.
Read this information carefully before starting to
operate the Kenwood Car Navigation System and
follow the instructions in this manual. Neither
Kenwood nor Garmin shall be liable for problems
or accidents resulting from failure to observe the
instructions in this manual.
The navigation system is designed to provide you
with route suggestions. It does not reflect road
closures or road conditions, weather conditions, or
other factors that may affect safety or timing while
driving.
Use the navigation system only as a navigational aid.
Do not attempt to use the navigation system for any
purpose requiring precise measurement of direction,
distance, location, or topography.
2WARNINGS
Failure to avoid the following potentially
hazardous situations could result in an accident
or collision resulting in death or serious injury.
When navigating, carefully compare information
displayed on the navigation system to all available
navigation sources, including information from
street signs, visual sightings, and maps. For safety,
always resolve any discrepancies or questions before
continuing navigation.
The Global Positioning System (GPS) is operated
by the United States government, which is solely
responsible for its accuracy and maintenance. The
government system is subject to changes that
could affect the accuracy and performance of all
GPS equipment, including the navigation system.
Although the navigation system is a precision
navigation device, any navigation device can be
misused or misinterpreted and, therefore, become
unsafe.
Always operate the vehicle in a safe manner.
Do not become distracted by the navigation system
while driving, and always be fully aware of all driving
conditions. Minimize the amount of time spent
viewing the screen of the navigation system while
driving, and use voice prompts when possible.
Do not enter destinations, change settings, or
access any functions requiring prolonged use of the
navigation system controls while driving. Stop your
vehicle in a safe and legal manner before attempting
such operations.
Keep the system volume at a low enough level to be
able to hear outside noises while driving. If you can
no longer hear outside noises, you may be unable
to react adequately to the traffic situation. This may
cause accidents.
The navigation system will not display the correct
current position of the vehicle the first time it is
used after purchase, or if the vehicle battery is
disconnected. GPS satellite signals will soon be
received, however, and the correct position will be
displayed.
Be careful of the ambient temperature. Using the
navigation system at extreme temperatures can lead
to malfunction or damage. Also note that the unit can
be damaged by strong vibration, by metal objects, or
by water getting inside the unit.
IMPORTANT INFORMATION
ÑVehicle Battery Preservation
This navigation system can be used when the ignition
key is turned to ON or ACC. To preserve the battery,
however, it should be used with the engine running
whenever possible. Using the navigation system for a
long time with the engine switched off can cause the
battery to run down.
ÑMap Data Information
One of the goals of Garmin is to provide customers
with the most complete and accurate cartography
that is available to us at a reasonable cost. We use
a combination of governmental and private data
sources, which we identify in product literature and
copyright messages displayed to the consumer.
Virtually all data sources contain some inaccurate or
incomplete data. In some countries, complete and
accurate map information is either not available or is
prohibitively expensive.
Download from Www.Somanuals.com. All Manuals Search And DownlEoandg. lish ñ 5
Features of Connected systems
By connecting this unit to Internet, you can use various services.
ÑCooperation with Route Collector site
•
•
•
•
Destinations and routes specified on the PC can be input to this navigation system.
(DNN9150BT/ DNN9150BTM)
The routes you have traveled and the songs you have listened to can be logged. (DNN9150BT/
DNN9150BTM)
By uploading music files to Dropbox and creating a play list on Route Collector site, you can
listen to music anywhere through streaming without music files on this unit.
Speech to Text (STT) and Text to Speech (TTS).
ÑUse of internet service
•
•
•
Streaming service such as Aupeo!.
Internet service such as email, and social networking service such as Facebook and Twitter.
Information (RSS, etc.) service.
Ñ4G, 3G, LTE or EDGE
ÑWi-Fi access point
•
Connect to Internet using the tethering
function of your smartphone or an Internet
device.
ÑWi-Fi (11n/g/b)
ÑAbout the account
•
To use internet services via this system, you
need to create an account in the Route
Collector site.
DNR8015BT/
DNR8015BTM
HOME
6
•
In addition to the owner account, you can
register up to four user accounts.
You can use a guest account as well.
By switching among accounts, you can secure
the privacy when using the mail feature or
social media.
•
•
✎ Notes
•
•
TTS (by Nuance)
STT (by Nuance)
To use the following services, you need
to register the corresponding free or
paid accounts.
ÑWi-Fi hotspot
•
This unit becomes the Wi-Fi access point
and you can enjoy music and video in a
smartphone Wi-Fi connected by Kenwood
Wireless Link.
•
•
•
•
Aupeo!
Facebook
Twitter
Dropbox
6 ñ EngDlisohwnload from Www.Somanuals.com. All Manuals Search And Download.
2Touch the corresponding key and set the
First Step
item.
Power on the unit and perform some setup steps
before using.
1Press the <8HOME> button.
DNR8015BT/
DNR8015BTM
Language Setup
Select the language used for the GUI and input
methods. Default is “English (United States)”.
HOME
6
1) Touch [Language Setup].
2) Select a language from the list.
The unit is turned on.
To turn off the unit:
WiFi Setup
Configure settings for connection to Wi-Fi.
Press the <8HOME> button for 1 second.
1) Touch [Wifi Setup].
2) Slide Wi-Fi to ON.
✎ NOTE
•
“Initial setup” also appears when the unit is reset.
3) Touch [Wi-Fi].
4) Select the Wi-Fi access point to register from
the list.
5) Enter the Password.
6) Touch [Connect].
After setting, press the < 6> button.
Date Setup
Set the date and time.
1) Touch [Date Setup].
2) Touch [Select time zone]. (DNR8015BT/
DNR8015BTM only)
3) Select a time zone.
After setting, press the < 6> button.
Account Setup
Set the information about the user of this unit.
1) Touch [Account Setup].
See Types of accounts, Create User Account and
Set Owner Account.
Download from Www.Somanuals.com. All Manuals Search And DownlEoandg. lish ñ 7
Types of accounts
Administrator
3Touch [Next].
4Touch the corresponding key and set the
As Administrator, you can create an owner account
and perform initial setup.
item.
You can log in to the system if you have not created
an owner account.
Guest
An account for guests such as your friends.
The guest can operate this unit, but cannot use the
functions related to mail, social media, and Route
Collector site.
Owner
The account for the person who manages this unit.
The owner can use the functions related to mail,
social media, and Route Collector site.
You can register users such as your family.
User
The account for the user of this unit.
The user can use the functions related to mail, social
media, and Route Collector site.
You can register up to 4 user accounts.
Locale (DNN9150BT/ DNN9150BTM)
Select the country for the navigation system.
The language, the distance unit, and the gasoline
unit are set.
Create User Account
✎ Preparation
•
•
•
To register yourself in the Route Collector site as a
user, you need a mail address.
Language
Select the language used for the control screen and
setting items. Default is “American English (en)”.
You can register yourself via the Web.
This step may be skipped if you have already
registered yourself in the Route Collector site.
1) Touch [Create Account].
After setting, touch [Enter].
Angle
Adjust the position of the monitor. Default is “0”.
After setting, touch [
].
2) Enter account information.
Color
You cannot register an account which has
already been used. Register another account
name.
Set the screen and button illumination color. You
can select whether to perform color scan and adjust
scanning color.
3) Touch [OK].
After setting, touch [
].
The account is temporarily registered in the
Route Collector site.
Camera
4) Activate the account.
Set the parameters for the camera.
A confirmation mail is sent to the registered mail
address. Open the indicated URL to complete
account registration.
After setting, touch [
].
DEMO
Set the demonstration mode. Default is “ON”.
Set Owner Account
1) Touch [Set Owner Account].
2) Enter account information.
Enter the information registered in the Route
Collector site.
3) Touch [OK].
8 ñ EngDlisohwnload from Www.Somanuals.com. All Manuals Search And Download.
5Touch [Finish].
✎ NOTE
For details on operations of each setting, refer to the
Instruction Manual.
ÑHow to prepare the remote control
Insert two “AAA”/“R03”-size batteries with the and
poles aligned properly, following the illustration
inside the case.
•
6Touch [Administrator] or [Owner].
!CAUTION
•
Put the remote controller in a place where it will
not move during braking or other operations. A
dangerous situation could result, if the remote
controller falls down and gets wedged under the
pedals while driving.
•
•
Do not leave the battery near fire or under direct
sunlight. A fire, explosion or excessive heat
generation may result.
Do not recharge, short, break up or heat the
battery or place it in an open fire. Such actions
may cause the battery to leak fluid. If spilled fluid
comes in contact with your eyes or on clothing,
immediately rinse with water and consult a
physician.
•
Place the battery out of reach of children. In the
unlikely event that a child swallows the battery,
immediately consult a physician.
Download from Www.Somanuals.com. All Manuals Search And DownlEoandg. lish ñ 9
Functions of the Buttons on the Front Panel
9
DNR8015BT/
DNR8015BTM
10
HOME
6
1
2
3
4
5
6
7
8
No.
Name/ Motion
No.
Name/ Motion
HOME
s(Reset)
1
6
•
If the unit or the connected unit fails
to operate properly, the unit returns
to initial settings when this button is
•
•
•
Pressing for 1 second turns the power off.
When the power off, turns the power on.
pressed (Instruction Manual P.135).
If the SI function is turned on, this
indicator flashes when the vehicle
ignition is off (Instruction Manual
P.111).
6(Back)
7
8
•
•
•
Return to the previously viewed screen.
Pressing for 1 second displays the Hands
Free screen (Instruction Manual
P.100).
R, S(Vol)
Adjusts volume.
2
3
4
G(Eject)
•
•
•
Ejects the disc.
Remote Sensor
Receives the remote control signal.
When the panel is opened, pressing
closes the panel and pressing for 1
second ejects the disc forcibly.
When the panel is closed, pressing for
1 second fully opens the panel to the
location of the SD card slot. (DNN9150BT/
DNN9150BTM)
•
NAV (DNN9150BT/ DNN9150BTM)
•
•
•
Displays the navigation screen.
Pressing for 1 second turns the screen
off.*
APPS (DNR8015BT/ DNR8015BTM)
Disc insert slot
A slot to insert a disc media.
9
p
•
Displays the APPS screen.
Pressing for 1 second turns the screen
off.*
•
•
SD card slot (DNN9150BT/ DNN9150BTM)
•
An SD card slot for upgrading the map.
For how to upgrade the map, refer to
the instruction manual of the navigation
system.
MENU
5
•
Displays the option menu screen.
•
Pressing for 1 second switches AV out
sources.
* The function of the [NAV]/ [APPS] button can be changed to
camera view function. (Instruction Manual P.109)
10 ñ EnDgoliwshnload from Www.Somanuals.com. All Manuals Search And Download.
ÑHow to insert an SD card
ÑList screen
There are some common function keys in the list
screens of most sources.
(DNN9150BT/ DNN9150BTM)
8
1) Press
<G> button for 1 second.
The panel fully opens.
2) Hold the SD card as the illustration in the
right and insert it into the slot until it clicks.
To eject the card:
Push the card until it clicks and then remove your
finger from the card.
The card pops up so that you can pull it out with
your fingers.
Labelled side
(Scroll)
0
Touch to scroll through texts on the display.
etc.
Touch keys with various functions are displayed
here.
Displayed keys differ depending on the current
audio source, status, etc.
Common Operation
For examples, see List screen (P.22) in the
Instruction Manual.
ÑGeneral
There are some functions which can be operated
from most screens.
ÑFlick scrolling
You can scroll the list screen by flicking the screen
up/down or right/left.
(Mixed Media Search)
Touch to display the Mixed Media Search screen.
(Quick menu)
Touch to display the quick menu. The content of the
menu are as follows.
: Displays the SETUP Menu screen.
: Displays the Audio Control Menu screen.
: Displays the control screen of current source.
Icon feature differs depending on the source.
(RETURN)
Returns to previous screen.
English ñ 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Login
Operation on the Home Screen
1Press the <HOME> button to turn the
1Press the <HOME> button to display the
power on.
Home screen.
2Select the login user.
3Enter the password.
2Flick the screen left or right to select
the Service panel, Media panel, Source
launcher panel, or Network contents
panel.
(Password)
Enter the registered password.
If you selected Administrator or Guest, this screen is
not displayed.
[Auto Login?]
Checking this checkbox allows you to log in to the
system automatically from the next time.
[Login]
Log in to the system.
✎ NOTE
•
If you forgot your password, create your new
password on the Route Collector site.
1 Service panel
Network widget: Displays the SNS, or RSS.
2 Media panel
Now playing: Displays the title of the song being
played or the name of the station you are listening
to, and allows you to perform simple operations.
Photo Frame Widget: Displays the Photo frame that
shows photos.
3 Source launcher panel
Allows you select a source.
4 Network contents panel
Allows you to select a network-related application.
12 ñ EnDgoliwshnload from Www.Somanuals.com. All Manuals Search And Download.
ÑSource launcher panel
Adding of a shortcut icon to Source
launcher panel
(Shortcut icon)
You can register sources you use frequently so that
you can start them quickly.
1) Touch [
] in Source launcher panel.
2) Touching the icon continuously to display
the Source launcher panel screen.
(All source list)
3) Drag the icon to an empty space.
Displays all sources.
All source list
(All source list)
You can scroll the list screen by flicking the screen
up/down.
(Home)
Returns to the Source launcher panel.
Moving or deleting of an icon on the
Source launcher panel
1) Touch and hold the icon.
2) Drag the icon to the desired position or
Recycle Bin.
English ñ 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Finding points of interest
1) Touch [Where To?].
2) Select a category and a subcategory.
3) Select a destination.
How to Use the
Navigation System
(DNN9150BT/ DNN9150BTM)
4) Touch [Go!].
✎ NOTE
1Press the <NAV> button to display the
•
To enter letters contained in the name, touch the
Search bar and enter the letters.
navigation screen.
2Operate the desired function from the
4Follow your route to the destination.
✎ NOTICE
The speed limit icon feature is for information
only and does not replace the driver’s
responsibility to abide by all posted speed limit
signs and to use safe driving judgment at all
times. Garmin and JVC KENWOOD will not be
responsible for any traffic fines or citations that
you may receive for failing to follow all applicable
traffic laws and signs.
Main Menu screen.
•
1
3
2
4
5
Your route is marked with a magenta line. As you
travel, your navigation system guides you to your
destination with voice prompts, arrows on the map,
and directions at the top of the map. If you depart
from the original route, your navigation system
recalculates the route.
GPS satellite strength.
Finds a destination.
Views the map.
1
2
3
4
5
Uses the Apps such as ecoRoute and Help.
Adjusts the settings.
1
2
4
✎ NOTE
5
•
You can get additional information about using the
navigation system from Help. To display Help, touch
[Apps] and then touch [Help].
3
6
7
8
9
Views the Next Turn page or the junction view
page, when available.
1
Views the Turn List page.
2
3
4
5
6
Views the Where Am I? page.
Stops the currents route.
•
For more information about your navigation system,
download the latest version of the Owner’s Manual
from manual.kenwood.com/edition/im387
Displays traffic information on the route.
Returns to the Main Menu.
3Enter your destination and start the
guidance.
14 ñ EnDgoliwshnload from Www.Somanuals.com. All Manuals Search And Download.
Updating the software
To update the navigation system software,
you must have an SD card, a USB mass storage
device and an internet connection.
2) Find your model and select [Software
Updates] > [Download].
Displays a different data field.
Views the Trip Computer.
Displays more options.
7
8
9
✎ NOTE
3) Read and accept the terms of the Software
License Agreement.
4) Follow the instructions on the Web site to
complete the installation of the software
update.
•
Touch and drag the map to view a different area of
the map.
•
A speed limit icon could appear as you travel on
major roadways.
Adding a stop
Updating maps
1) While navigating a route, touch [
then touch [Where To?].
2) Search for the extra stop.
3) Touch [Go!].
] and
You can purchase updated map data from Garmin
or ask your Kenwood dealer or Kenwood service
center for details.
2) Select [Order Map Updates] for your
Kenwood unit.
4) Touch [Add to Active Route] to add this stop
before your final destination.
3) Follow the Web site instructions to update
your map.
Taking a detour
1) While navigating a route, touch [
].
2) Touch [
].
ÑOther Features
Manually avoiding traffic on your route
(region code 3 area only)
1) From the map, touch the traffic icon.
2) Touch [Traffic On Route].
3) If necessary, touch the arrows to view other
traffic delays on your route.
4) Touch [
] > [Avoid].
Viewing the traffic map (region code 3
area only)
1) The traffic map shows color-coded traffic
flow and delays on nearby.
About traffic (region code 3 area only)
✎ NOTICE
•
Traffic service is not available in some areas or
countries.
•
Garmin and JVC KENWOOD are not responsible
for the accuracy or timeliness of the traffic
information.
•
Your navigation system can receive traffic
information using the built-in traffic receiver.
The traffic receiver must be in data range of a
station transmitting traffic data to receive traffic
information. The traffic subscription activates
automatically after your navigation system
acquires satellite signals while receiving traffic
signals from the service provider.
English ñ 15
Download from Www.Somanuals.com. All Manuals Search And Download.
2Control the music you are listening to on
How to Play Music
the source control screen.
You can play audio files from music CD, disc media,
USB storage device and iPod.
The following symbols indicate the keys on the
screen.
The functions of the keys are the same despite the
difference of the source you are listening to.
✎ NOTE
•
For details on playable file format, media format,
iPod model, etc., refer to the Instruction Manual.
(P.136)
•
To connect with iPod/iPhone/Android the setting
is necessary. Refer to iPod/ iPhone/ Android setup
Touch [
]
Z
1Connect the media you want to play as
shown below.
Disc
1) Press the <G> button to open the front
panel.
2) Insert the disc into the slot.
The panel closes automatically and playback
starts.
Basic operations from this screen
L
Plays or pauses.
I
Stops playing.
G
Disconnects the device.
0
EF
Searches the previous/next content.
ABor move the cursor in the center
bar
Fast forwards or Fast backwards (Disc media,
CD, USB device only):
To eject the disc:
1) Press the <G> button.
iPod, USB device
1) Connect the device with each cable.
Playback starts.
Repeats current content.
Plays all contents in random order.
✎ NOTE
•
•
For other operations, refer to the Instruction Manual.
If desired key is not displayed in the multi-function
To disconnect the device:
1) Touch [G] on the screen and disconnect the
device from the cable.
bar, touch the [
] to switch the menu.
3Search the track/file you want to listen to.
✎ NOTE
List search
•
It applies when you set the iPod/iPhone connection
with cable.
1) Touch center of the screen.
The content list of the media being played
is displayed.
If the information of the current track only
is displayed, touch [
display.
] to switch the list
16 ñ EnDgoliwshnload from Www.Somanuals.com. All Manuals Search And Download.
How to Play Movie
You can play DVD video, Video CD (VCD), movie files
from disc media, iPod and USB storage device.
✎ NOTE
•
For details on playable file format, device format,
etc., refer to the Instruction Manual.
1Connect the media you want to play.
Refined search
For the method of connecting, see How to Play
1) Touch [
].
2) Touch the desired refinement method.
The list is refined by the item you selected.
3) Touch the desired item.
2Control the movie by touching the
screen.
Each area on the screen has a separate function.
3
3
✎ NOTE
•
For details on searching operations, refer to Search
Operation (P.66) in the Instruction Manual.
1
2
No.
1
Name/Motion
Displays the movie control screen.
Displays the Source Control screen.
2
•
•
Searches the next/previous content or file.
Scrolling from center of display to left
or right performs fast backward or fast
forward.
3
To stop fast backward/forward, touch center
of the display.*1
•
*1 For iPod/USB, this function may be unavailable
depending on the playing file format.
✎ NOTE
•
For operations on the source control screen, see
However, searching by category/link/album artwork
is not available.
English ñ 17
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Listen to the Radio
How to Make a Phone Call
You can use your Bluetooth cell-phone when paired
to this unit.
1Press the <HOME> button twice to the
Source launcher panel.
1Register your cell-phone to the unit.
2Touch [
] in the Source launcher panel.
Follow as the procedures shown below. For
detailed operation, see Registering the
Bluetooth Unit (P.97) in the Instruction
Manual.
3Touch [TUNER].
The unit switches to the Radio tuner source.
1) Press the <HOME> button twice to the
Source launcher panel.
4Operate on the source control screen.
Station search
2) Touch [
] in the Source launcher panel.
1) Touch [
].
3) Touch [STANDBY].
Sub function menu appears.
2) Touch [AM] or [FM] to select the band.)
3) Touch [A] or [B] to tune in the desired
station.
4) Press and hold the < 6> button.
5) Touch [
].
6) Touch [Search].
Searched Device List screen appears.
Auto memory
1) Touch [
].
Sub function menu appears.
2) Touch [AM] or [FM] to select the band.
3) Touch [
].
4) Touch [AME].
5) Touch [A] or [B] in the sub function
menu.
Auto memory starts.
7) Select your cell-phone from the displayed list
in the Searched Device List screen.
8) Enter PIN code form the cell-phone.
Registering is completed.
Recalling the preset station
1) Touch [P#].
You can also display the preset list by
touching the frequency display in the center.
The PIN code is set to “0000” as default.
✎ NOTE
2Connect your cell-phone to the unit.
•
For other operations, see Radio Basic Operation
(P.86) in the Instruction Manual.
1) Touch the device name you want to connect
in the Bluetooth SETUP screen.
2) Touch [ON] of [TEL(HFP)] in the BT
Connection Settings screen.
The selected device is connected to the unit.
18 ñ EnDgoliwshnload from Www.Somanuals.com. All Manuals Search And Download.
Call by voice
You can make a voice call using the voice
recognition function of the cell-phone.
1) Touch [
].
2) Pronounce the name registered in the cell-
phone.
✎ NOTE
When registration of your cell-phone is
completed, the phone book of the cell-
phone is automatically downloaded to this
unit.
•
For detailed operation, see Using Hands-Free
Feature (P.100) in the Instruction Manual.
✎ NOTE
•
Touch [Audio(A2DP)] if you want to connect the
device as an audio player.
3Make or receive a phone call.
See the table below for each operation method.
Call by entering a phone number
1) Touch [
2) Enter a phone number with number keys.
3) Touch [ ].
].
Call using call records
1) Touch [
Calls), or [
] (Incoming Calls), [
] (Missed Calls).
] (Outgoing
2) Select the phone number from the list.
3) Touch [ ].
Call using the phonebook
1) Touch [ ].
2) Select the name from the list.
3) Select the number from the list.
4) Touch [
].
Call using the preset number
1) Touch [Preset #] to start calling the
corresponding phone number.
English ñ 19
Download from Www.Somanuals.com. All Manuals Search And Download.
touching to cause a short circuit, then replace the
old fuse with one with the same rating.
Installation
•
•
•
Insulate unconnected wires with vinyl tape or other
similar material. To prevent a short circuit, do not
remove the caps on the ends of the unconnected
wires or the terminals.
ÑBefore Installation
Before installation of this unit, please note the
following precautions.
Connect the speaker wires correctly to the terminals
to which they correspond. The unit may be
damaged or fail to work if you share the ¤wires or
ground them to any metal part in the car.
When only two speakers are being connected to
the system, connect the connectors either to both
the front output terminals or to both the rear output
terminals (do not mix front and rear). For example,
if you connect the ¢connector of the left speaker
to a front output terminal, do not connect the ¤
connector to a rear output terminal.
After the unit is installed, check whether the brake
lamps, blinkers, wipers, etc. on the car are working
properly.
Mount the unit so that the mounting angle is 30°
or less.
the internal temperature. Do not mount the unit in
a place where the cooling fan of the unit is blocked.
Blocking these openings will inhibit the cooling of
the internal temperature and result in malfunction.
Do not press hard on the panel surface when installing
the unit to the vehicle. Otherwise scars, damage, or
failure may result.
!WARNINGS
•
If you connect the ignition wire (red) and the
battery wire (yellow) to the car chassis (ground),
you may cause a short circuit, that in turn may
start a fire. Always connect those wires to the
power source running through the fuse box.
Do not cut out the fuse from the ignition wire
(red) and the battery wire (yellow). The power
supply must be connected to the wires via the
fuse.
•
!CAUTION
•
•
Install this unit in the console of your vehicle.
Do not touch the metal part of this unit during
and shortly after the use of the unit. Metal part
such as the heat sink and enclosure become hot.
•
•
✎ NOTES
•
Mounting and wiring this product requires skills and
experience. For best safety, leave the mounting and
wiring work to professionals.
•
•
Make sure to ground the unit to a negative 12V DC
power supply.
Do not install the unit in a spot exposed to direct
sunlight or excessive heat or humidity. Also avoid
places with too much dust or the possibility of water
splashing.
•
•
Reception may drop if there are metal objects near
the Bluetooth antenna and WI-FI receiver.
•
•
Do not use your own screws. Use only the screws
provided. If you use the wrong screws, you could
damage the unit.
Bluetooth antenna area
If the power is not turned ON (“PROTECT” is
displayed), the speaker wire may have a short-
circuit or touched the chassis of the vehicle and
the protection function may have been activated.
Therefore, the speaker wire should be checked.
If your car’s ignition does not have an ACC position,
connect the ignition wires to a power source that
can be turned on and off with the ignition key. If you
connect the ignition wire to a power source with a
constant voltage supply, such as with battery wires,
the battery may be drained.
M4 x 8mmMAX
WiFi
Recever
iPod/
AV-IN2
•
5V=500mA
WI-FI receiver
REMO
TE
POWER
•
Install the WI-FI receiver besides the place enclosed
by the metal.
•
•
If the console has a lid, make sure to install the unit
so that the faceplate will not hit the lid when closing
and opening.
If the fuse blows, first make sure the wires aren’t
20 ñ EnDgoliwsnhload from Www.Somanuals.com. All Manuals Search And Download.
ÑSupplied accessories
ÑUnit
First of all, make sure that all accessories are
supplied with the unit.
1) To prevent a short circuit, remove the key from
the ignition and disconnect the ¤terminal of
the battery.
1 ...1
2 ...1
3 ...2
4 ...6
5 ...6
6 ...1
7 *1 ...1
8 *1 ...1
9 ...1
2) Make the proper input and output wire
connections for each unit.
3) Connect the speaker wires of the wiring harness.
4) Connect the wiring harness wires in the
following order;
ground, battery, ignition.
5) Connect the wiring harness connector to the
unit.
(3.5 m)
6) Install the unit in your car.
7) Reconnect the ¤terminal of the battery.
9) Perform the Initial Setup.
(2 m)
Non-Japanese cars
(3 m)
0 ...1
Bend the tabs of the
mounting sleeve with
a screwdriver or similar
utensil and attach it in
place.
(M5x6mm)
- ...1
Japanese cars
4 or 5
4 or 5
Car Bracket
(M5x7mm)
*1 DNN9150BT/
DNN9150BTM only
✎ NOTE
•
Make sure that the unit is installed securely in place.
If the unit is unstable, it may malfunction (eg, the
sound may skip).
English ñ 21
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Painting the GPS antenna with (metallic) paint may
cause a drop in performance.
ÑTrim plate
1) Attach accessory 6 to the unit.
ÑMicrophone unit
1) Check the installation position of the
microphone (accessory 9).
2) Clean the installation surface.
3) Install the microphone.
4) Wire the microphone cable up to the unit with it
secured at several positions using tape or other
desired method.
6
9
ÑGPS antenna (DNN9150BT/ DNN9150BTM)
GPS antenna is installed inside of the car. It should
be installed as horizontally as possible to allow easy
reception of the GPS satellite signals.
To mount the GPS antenna inside your vehicle:
1) Clean your dashboard or other surface.
2) Remove the separator of the metal plate
(accessory 8).
3) Press the metal plate (accessory 8) down firmly
on your dashboard or other mounting surface.
You can bend the metal plate (accessory 8) to
conform to a curved surface, if necessary.
4) Remove the separator of the GPS antenna
(accessory 7), and stick the antenna to the
metal plate (accessory 8).
Fix a cable with a commercial item of tape.
7
8
Remove the separator of the microphone, and stick
the microphone to the place shown above.
✎ NOTE
Adjust the direction of the microphone to the
driver.
•
•
•
Depending on the type of car, reception of the GPS
satellite signals might not be possible with an inside
installation.
Please install this GPS antenna in an area away from
any antennas that are used with CB radios or satellite
televisions.
The GPS antenna should be installed at a position
that is spaced at least 12 inch (30 cm) from cellular
phone or other transmitting antennas. Signals from
the GPS satellite may be interfered with by these
types of communication.
✎ NOTE
•
Install the microphone as far as possible from the
cell-phone.
22 ñ EnDgoliwsnhload from Www.Somanuals.com. All Manuals Search And Download.
ÑRemoving the trim plate
ÑRemoving the unit
1) Engage the catch pins on the extraction key
(accessory3) and remove the two locks on the
lower level.
1) Remove the trim plate by referring to step 1 in
“Removing the trim plate”.
2) Insert the two extraction key (accessory3)
Lower the trim plate (accessory6) and pull it
forward as shown in the figure.
deeply into the slots on each side, as shown.
6
3
3
Catch
Lock
3) Lower the extraction key toward the bottom,
and pull out the unit halfway while pressing
towards the inside.
✎ NOTE
•
The trim plate can be removed from the top side in
the same manner.
2) When the lower level is removed, remove the
upper two locations.
✎ NOTE
•
Be careful to avoid injury from the catch pins on the
extraction key.
4) Pull the unit all the way out with your hands,
being careful not to drop it.
Download from Www.Somanuals.com. All Manuals Search And DowEnlnoagdli.sh ñ 23
ÑConnecting wires to terminals
HDMI/MHL
GPS
M4 x 8mmMAX
iPod/
AV-IN2
MIC
AV-IN/OUT
AV-OUT
AUDIO
REMO
TE
OWER
R
L
Ignition key
switch
Accessory 1
ACC
Red (Ignition wire)
Speaker impedance: 4-8 Ω
White/Black
Yellow (Battery wire)
To front left
speaker
+
Car fuse box
(Main fuse)
Car fuse box
White
Black (Ground wire) ¤
(To car chassis)
Gray/Black
A
To front right
speaker
A
+
Light Blue/Yellow
(Steering remote control wire)
Gray
Battery
To steering remote
REMOTE STEERING
CONT
WHEEL
REMOTE
INPUT
To use the steering wheel remote control
feature, you need an exclusive remote adapter
(not supplied) matched to your car.
Green/Black
Green
To rear left
speaker
+
+
Orange/White (Dimmer
control wire)
To car light control switch
ILLUMI
Purple/Black
Purple
To rear right
speaker
Connect to the terminal that is grounded
when either the telephone rings or during
conversation.
Brown (Mute control wire)
MUTE
To use the Mute feature, you need to hook
up this wire to your telephone by using a
commercial telephone accessory.
Blue
(Antenna control wire)
Depending on what antenna you are using,
connect either to the control terminal of the
motor antenna, or to the power terminal for the
booster amplifier
ANT CONT
of the film-type antenna. (Max. 300mA, 12V)
Blue/White
(Power control wire)
When using the optional power amplifier,
connect to its power control terminal.
P. CONT
If no connections are made,
do not let the cable come out from the tab.
24 ñ EnDgoliwshnload from Www.Somanuals.com. All Manuals Search And Download.
ÑSystem connection
Accessory 7: GPS Antenna
(DNN9150BT/ DNN9150BTM only)
Accessory 9:
Bluetooth Microphone
WI-FI receiver
FM/AM antenna input
(0.8 m)
- Reception may drop if there
are metal objects near the
Bluetooth antenna and WI-FI
receiver.
- Install the WI-FI receiver
besides the place enclosed by
the metal.
WiFi
Receiver
5V=500mA
HDMI/MHL
GPS
M4 x 8mmMAX
iPod/
AV-IN2
AV-IN/OUT
AV-OUT
AUDIO
REMO
TE
POWER
R
L
Fuse
(10A)
Cooling fan
Connect to the vehicle’s
parking brake detection
switch harness.
AV-OUT Output
- Audio Output
Accessory 2
Accessory 0
Light Green (Parking sensor wire)
PRK SW
AV-OUT Output
- Visual Output
For best safety, be sure to connect
the parking sensor.
AV-IN1 input
- Yellow (Visual input)
- Red (Audio Right input)
- White (Audio Left input)
Purple/White (Reverse sensor wire)
REVERSE
Connect to vehicle’s reverse lamp harness
when using the optional rear view camera.
Rear view camera input
Front view camera input
Green/Red
To CMOS-3xx series (Optional
Accessory) camera control
terminal
Green/White
Download from Www.Somanuals.com. All Manuals Search And DowEnlnoagdli.sh ñ 25
Ñ3 way speaker system setup
Region code 3 area
Connect the speaker wires
HDMI/MHL
GPS
M4 x 8mmMAX
iPod/
AV-IN2
MIC
AV-IN/OUT
AV-OUT
AUDIO
REMO
TE
WER
R
L
Subwoofer Preout
- Red (Audio Right Output)
- White (Audio Left Output)
Accessory 1
Speaker impedance: 4-8 Ω
Mid Range Preout
- Red (Audio Right Output)
- White (Audio Left Output)
Tweeter Preout
- Red (Audio Right Output)
- White (Audio Left Output)
White/Black
To mid range left
speaker
+
+
White
Gray/Black
Preout
To mid range right
speaker
RCA Cable
(sold separately)
Gray
Power amplifier
(optional accessory)
Green/Black
To tweeter left
speaker
Speaker
+
+
Green
Input
When connecting to an external amplifier, connect
its ground wire to the car's chassis to avoid
damaging the unit.
Purple/Black
Purple
To tweeter right
speaker
NOTE
• For how to connect speaker wires to terminals
other than speaker terminals and Preout
terminals, see Connecting wires to terminals
26 ñ EnDgoliwshnload from Www.Somanuals.com. All Manuals Search And Download.
Switching between speaker systems
Switch to the 3 way speaker system following the
procedure below.
6Touch [Yes].
The 2 way speaker system is switched to the 3 way
speaker system.
!
✎ NOTE
•
Be sure to set the speaker network correctly.
Connecting 3 way speakers with the 2 way mode
selected can break the speakers.
•
When the 3-way speaker system is selected,
the following functions are disabled. (See the
Instruction Manual.)
-
-
Zone Control (P.126)
DSP select (P.122)
1Press the <HOME> button twice to the
Source launcher panel.
- Fader of Controlling General Audio (P.122)
For speaker setup and crossover setup, see Setting
Audio (P.118) in the Instruction Manual.
•
2Touch [
] in the Source launcher
panel.
3Touch [STANDBY].
4Press the <∞> button and <0> button
for 1 second at the same time.
Speaker system select screen appears.
DNR8015BT/
DNR8015BTM
HOME
6
5Touch [3way].
A confirmation screen appears.
Download from Www.Somanuals.com. All Manuals Search And DownElnoagdli.sh ñ 27
ÑOptional accessory connection
3
4
3
DNN9150BT/
DNN9150BTM
DNR8015BT/
DNR8015BTM
1
2
1
2
USB
HDMIL
HDML
GPS
M4
x
8mmMAX
M4 x 8mmMAX
iPod/
A
iPod/
A
MIC
AV-IN/OUT
MIC
AV-IN/OUT
AV-OUT
AUDIO
AV-OUT
AUDIO
R
TE
R
TE
POWER
POWER
R
L
R
L
5
6
5
6
Android smartphone
(sold separately)
USB device
(sold separately)
4
3
1
KCA-MH100 (1.8m)
(Optional Accessory)
HDMI/ MHL input
1
MHL maximum power supply current :
5 V 900 mA
When you connect the cable to HDMI/MHL
terminal, remove the fixture. After connecting the
cable, put the fixture again.
Rear Preout
- Red (Audio Right Output)
- White (Audio Left Output)
5
HDMI/ MHL connector
Fixture
Front Preout
- Red (Audio Right Output)
- White (Audio Left Output)
R
L
Subwoofer Preout
- Red (Audio Right Output)
- White (Audio Left Output)
When connecting to an external amplifier, connect
its ground wire to the car's chassis to avoid damaging
the unit.
iPod input / AV-IN2 (CA-C3AV; Optional
2
Accessory) input
(iPod/ AV-IN2 switchable)
iPod/ USB terminal (0.8m)
3
iPod/ USB maximum power supply current :
Accessory - Steering remote harness
Connect to vehicle's steering remote harness.
Contact your Kenwood dealer for details.
6
5 V
1 A
USB terminal (0.8m)
4
(DNN9150BT/ DNN9150BTM only)
USB maximum power supply current :
5 V
500 mA
28 ñ EnDgoliwsnhload from Www.Somanuals.com. All Manuals Search And Download.
iPod/ iPhone/ Android setup
iPod/iPhone
(sold separately)
ÑAndroid connection
To connect the Android device with this unit,
the cable (sold separately) and the profile which
your Android device supports are necessary as
follows:
KCA-iP103 (0.8m)
(Optional Accessory)
3
Music
To listen to music and watch video of APPS
source
Video and Music (HDMI)
–
–
–
–
MHL device
KCA-MH100
Bluetooth profile: SPP
Application link setup: HDMI/MHL + BT
Lightning Digital AV
Adapter
(sold separately)
KCA-HD100 (1.8m)
(Optional Accessory)
1
3
To listen to music of APPS source
KCA-iP103 (0.8m) (Charging)
(Optional Accessory)
–
–
–
Bluetooth profile: A2DP
Bluetooth profile: SPP
Application link setup: Bluetooth (P.31)
iPod
(sold separately)
To listen to music of Bluetooth Audio source
3
–
–
Bluetooth profile: A2DP
Bluetooth profile: AVRCP
USB terminal (0.8m)
KCA-iP102
(Optional Accessory)
✎ NOTE
•
Music
When you select Pandora source the setting of
Application link setup (P.31) is also necessary.
In the APPS source, some functions can be
controlled from this unit and they depend on the
applications. Refer to Apps Operation (P.74) in
the Instruction Manual.
Video and Music (analog)
AV Output (1.8m)
KCA-iP202
(Optional Accessory)
2
•
3
USB terminal (0.8m)
•
Do not leave the cable or the adapter made by
other makers inside the car. It might lead the
malfunction caused by heat.
ÑiPod/iPhone connection and setting
Connectable iPod/iPhone
The following models can be connected to this
unit.
Made for
• iPhone 5s
• iPhone 5c
• iPhone 5
• iPhone 4S
• iPhone 4
• iPhone 3GS
• iPhone 3G
NOTE
• iPhone
• For the connection and the setting of iPod/iPhone refer
• iPod touch (5th generation)
• iPod touch (4th generation)
• iPod touch (3rd generation)
• For the connection and the setting of Android
Download from Www.Somanuals.com. All Manuals Search And DowEnlnoagdli.sh ñ 29
• iPod touch (2nd generation)
• iPod touch (1st generation)
• iPod classic
other makers inside the car. It might lead the
malfunction caused by heat.
• iPod with video
iPod/iPhone connection setup
When you first select iPod as a source, the setting
screen of the iPod/iPhone connection will appear.
• iPod nano (7th generation)
• iPod nano (6th generation)
• iPod nano (5th generation)
• iPod nano (4th generation)
• iPod nano (3rd generation)
1Press the <HOME> button twice to the
Source launcher panel.
iPod/iPhone connection
2Touch [
] in the Source launcher
To connect the iPod/iPhone with this unit, the
cable, adapter (both sold separately), and the
profile which your iPod/iPhone supports are
necessary as follows:
panel.
3Touch [iPod].
iPod connection setup screen appears.
To listen music and watch video with
Lightning connector device
4Touch [CHANGE].
–
–
–
–
–
Lightning Digital AV Adapter
KCA-HD100
KCA-iP103
Bluetooth profile: SPP
5Set each item as follows.
iPod connection setup: HDMI + BT (P.30)
To listen music with Lightning connector
device
–
–
KCA-iP103
iPod connection setup: USB 1Wire (P.30)
To listen music and watch video with 30-pin
connector device (analog)
–
–
KCA-iP202
iPod connection setup: USB+AV-IN (P.30)
To listen music with 30-pin connector device
USB + AV-IN
Select when connecting with KCA-iP202.
–
–
KCA-iP102
iPod connection setup: USB 1Wire (P.30)
USB 1Wire
To listen to music via Bluetooth
Select when connecting with KCA-iP103 or KCA-
iP102.
–
–
–
Bluetooth profile: A2DP
Bluetooth profile: SPP
iPod connection setup: Bluetooth (P.30)
HDMI + BT
Select when connecting with KCA-HD100 and
Lightning Digital AV Adapter.
To listen to music of Bluetooth Audio source
–
–
Bluetooth profile: A2DP
Bluetooth profile: AVRCP
Bluetooth
Select when connecting via Bluetooth only.
✎ NOTE
•
When you select Pandora source the setting of
Application link setup (P.31) is also necessary.
In the APPS source, some functions can be
controlled from this unit and they depend on the
applications. Refer to Apps Operation (P.74) in
the Instruction Manual.
6Touch [Next].
•
Confirmation screen appears.
For the setting refer to Application link setup
•
Do not leave the cable or the adapter made by
30 ñ EnDgoliwsnhload from Www.Somanuals.com. All Manuals Search And Download.
7Touch [Done].
✎ NOTE
When you select “HDMI + BT” or “Bluetooth” in step
5, Bluetooth device selection screen will appear.
Select the iPod/iPhone to be connected.
5Select the device installed the apps.
•
6Select the way to connect the device with
this unit.
When selecting [iPod/iPhone]
If a connectable Bluetooth device is not displayed,
touch [Search] and do the pairing of the devices.
“iPod connection setup” also appears when the unit
is reset.
•
•
The setting of “iPod connection setup” is just for the
unit and regardless of the account.
ÑApplication link setup
When you first select Apps as a source, the setting
screen for the connection with the device installed
the apps will appear.
For the setting items refer to iPod/iPhone
When selecting [Android/Other]
1Press the <HOME> button twice to the
Source launcher panel.
2Touch [
] in the Source launcher
panel.
3Touch [APPS].
Application link setup screen appears.
4Touch [CHANGE].
HDMI/MHL + BT
Select when connecting with KCA-MH100.
Bluetooth
Select when connecting via Bluetooth only.
7Touch [Next].
Confirmation screen appears.
8Touch [Done].
English ñ 31
Download from Www.Somanuals.com. All Manuals Search And Download.
✎ NOTE
BlackBerry®
•
For the details of the necessary cable and adapter
to connect with iPod/iPhone and Android, refer to
•
download the Pandora application.
Bluetooth must be built in and the following profiles
must be supported.
•
•
When you select “HDMI + BT”, “HDMI/MHL +
BT” or “Bluetooth” in step 6, Bluetooth device
selection screen will appear. Select the device to be
connected.
- SPP (Serial Port Profile)
- A2DP (Advanced Audio Distribution Profile)
✎ NOTE
•
The Pandora service is available only in the U.S,
Australia and New Zealand.
•
Because Pandora® internet radio is a third-party
service, the specifications are subject to change
wihtout prior notice. Accordingly, compatibility
may be impaired or some or all of the services may
become unavailable.
•
•
Some Pandora® functionality cannot be operated
from this unit.
For issues using the Pandora® application, please
contact Pandora at [email protected]
If a connectable Bluetooth device is not displayed,
touch [Search] and do the pairing of the devices.
“Application link setup” also appears when the unit
is reset.
The setting of “Application link setup” is just for the
unit and regardless of the account.
ÑCopyrights
•
The Bluetooth word mark and logos are owned by
the Bluetooth SIG, Inc. and any use of such marks by
JVC KENWOOD Corporation is under license. Other
trademarks and trade names are those of their
respective owners.
•
•
•
•
The “AAC” logo is a trademark of Dolby Laboratories.
“Made for iPod” and “Made for iPhone” mean that an
electronic accessory has been designed to connect
specifically to iPod, or iPhone, respectively, and
has been certified by the developer to meet Apple
performance standards. Apple is not responsible for
the operation of this device or its compliance with
safety and regulatory standards. Please note that the
use of this accessory with iPod, or iPhone may affect
wireless performance.
About This Unit
ÑRequirements Pandora®:
Requirements for listening to the Pandora® are as
follows:
•
A smartphone with the latest Pandora application
installed.
A Pandora account (if you do not have an account,
create one for free using the mobile app or on
www.pandora.com).
•
•
iPhone, iPod, iPod classic, iPod nano, and iPod touch
are trademarks of Apple Inc., registered in the U.S.
and other countries.
•
An active internet connection.
Lightning is a trademark of Apple Inc.
iPhone or iPod touch
is a trademark of DVD Format/Logo
Licensing Corporation registered in the U.S., Japan
and other countries.
This item incorporates copy protection technology
that is protected by U.S. patents and other
intellectual property rights of Rovi Corporation.
Reverse engineering and disassembly are
prohibited.
•
Apple iPhone or iPod touch with iOS 3 or later
installed.
•
•
•
Latest version of the Pandora application (search
App Store for Pandora and install).
Android™
•
Latest version of the Pandora Android application
(search Google Play for Pandora and install).
•
Manufactured under license from Dolby
Laboratories.
Dolby and the double-D symbol are trademarks of
Dolby Laboratories.
32 ñ EnDgoliwshnload from Www.Somanuals.com. All Manuals Search And Download.
•
Adobe, Acrobat and Reader are either registered
trademarks or trademarks of Adobe Systems
Incorporated in the United States and/or other
countries.
Android is a trademark of Google Inc.
Twitter is a registered trademark of Twitter, Inc.
Facebook® is a registered trademark of Facebook
Inc.
Nuance is a registered trademark of Nuance
Communications, Inc.
“aupeo” is a trade mark of Aupeo Ltd.
Dropbox is a trademark of Dropbox Inc.
The terms HDMI and HDMI High-Definition
Multimedia Interface, and the HDMI logo are
trademarks or registed trademarks of HDMI
Licensing LLC in the United States and other
countries.
FROM A VIDEO PROVIDER LICENSED TO PROVIDE
AVC VIDEO. NO LICENSE IS GRANTED OR SHALL
BE IMPLIED FOR ANY OTHER USE. ADDITIONAL
INFORMATION MAY BE OBTAINED FROM MPEG LA,
L.L.C. SEE HTTP://WWW.MPEGLA.COM
•
•
•
•
MPEG-4 Visual
THIS PRODUCT IS LICENSED UNDER THE MPEG-
4 VISUAL PATENT PORTFOLIO LICENSE FOR
THE PERSONAL AND NON-COMMERCIAL USE
OF A CONSUMER FOR (i) ENCODING VIDEO IN
COMPLIANCE WITH THE MPEG-4 VISUAL STANDARD
(“MPEG-4 VIDEO”) AND/OR (ii) DECODING MPEG-
4 VIDEO THAT WAS ENCODED BY A CONSUMER
ENGAGED IN A PERSONAL AND NON-COMMERCIAL
ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO
PROVIDER LICENSED BY MPEG LA TO PROVIDE
MPEG-4 VIDEO. NO LICENSE IS GRANTED OR SHALL
BE IMPLIED FOR ANY OTHER USE. ADDITIONAL
INFORMATION INCLUDING THAT RELATING TO
PROMOTIONAL, INTERNAL AND COMMERCIAL USES
AND LICENSING MAY BE OBTAINED FROM MPEG LA,
LLC. SEE HTTP://WWW.MPEGLA.COM.
•
•
•
•
•
•
MHL and the MHL logo are a trademark or
registered trademark of MHL, LLC.
- Incorporates MHL 2
ABOUT DIVX VIDEO: DivX® is a digital video
format created by DivX, LLC, a subsidiary of Rovi
Corporation. This is an official DivX Certified® device
that plays DivX video. Visit divx.com for more
information and software tools to convert your files
into DivX videos.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX
Certified® device must be registered in order to play
purchased DivX Video-on-Demand (VOD) movies.
To obtain your registration code, locate the DivX
VOD section in your device setup menu. Go to vod.
divx.com for more information on how to complete
your registration.
DivX®, DivX Certified® and associated logos are
trademarks of Rovi Corporation or its subsidiaries
and are used under license.
QR Code ® is registered trademarks of DENSO WAVE
INCORPORATED in JAPAN and other countries.
The aptX® software is copyright CSR plc or its group
companies. All rights reserved. The aptX® mark and
the aptX logo are trade marks of CSR plc or one of
its group companies and may be registered in one
or more jurisdictions.
•
libFLAC
Copyright (C) 2000,2001,2002,2003,2004,2005,2006,2
007,2008,2009 Josh Coalson
Redistribution and use in source and binary forms,
with or without modification, are permitted
provided that the following conditions are met:
- Redistributions of source code must retain the
above copyright notice, this list of conditions and
the following disclaimer.
•
- Redistributions in binary form must reproduce the
above copyright notice, this list of conditions and
the following disclaimer in the documentation and/
or other materials provided with the distribution.
- Neither the name of the Xiph.org Foundation
nor the names of its contributors may be used to
endorse or promote products derived from this
software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDERS AND ONTRIBUTORS ``AS IS’’ AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE FOUNDATION OR CONTRIBUTORS BE LIABLE
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT
OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF
•
•
•
•
AVC
THIS PRODUCT IS LICENSED UNDER THE AVC
PATENT PORTFOLIO LICENSE FOR THE PERSONAL
USE OF A CONSUMER OR OTHER USES IN WHICH IT
DOES NOT RECEIVE REMUNERATION TO (i) ENCODE
VIDEO IN COMPLIANCE WITH THE AVC STANDARD
(“AVC VIDEO”) AND/OR (ii) DECODE AVC VIDEO
THAT WAS ENCODED BY A CONSUMER ENGAGED
IN A PERSONAL ACTIVITY AND/OR WAS OBTAINED
Download from Www.Somanuals.com. All Manuals Search And DowEnlnoagdli.sh ñ 33
LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGE.
(2) We shall assume no responsibility for any loss or
damage that may be incurred by the User due to its
use of or inability to use the Service, regardless of
whether such loss or damage is direct or indirect,
foreseeable or unforeseeable, including but not
limited to special damages.
ÑKENWOOD Route Network Service “Route
Collector” User’s Agreement
(3) We shall not be involved in nor assume
responsibility for any acts, problems, and other
issues between Users.
This KENWOOD Route Network Service “Route
Collector” User’s Agreement (“Agreement”) sets forth
the terms and conditions for use of the KENWOOD
Route Network Service “Route Collector” provided by
JVCKENWOOD Corporation (“Service”) to the users
who fulfill the requirements for “Conditions of Use” in
the paragraph 1 (“User(s)”), and the rules for handling
User’s information necessary for use this Service.
(4) Should any third parties suffer losses or damages
as a result of the User’s use of the Service, we shall
assume no responsibility therefor.
(5) Should the User suffer losses or damages from
misuse by any third parties of the User’s registered
user account name or password for the Service, we
shall assume no responsibility therefor.
1. Conditions of Use
4. Prohibited Matters
Users who desire to take advantage of this Service
must however first register themselves upon agreeing
to the terms of this Agreement. This Service may only
be used by Users for personal use, not for commercial
use.
Concerning the use of the Service, the following or
similar acts by the User are prohibited. Further, should
we determine that the User has violated the terms of
this Agreement, we reserve the right to suspend use
of the Service by the User without prior notice, or take
other necessary measures as we may deem necessary.
In such case, we bear no obligation to disclose our
reasons therefor.
The terms of this Agreement may be revised or
modified as necessary at our option without prior
notice. In such event, Users shall hereby agree to the
application of any such revisions or modifications as a
condition to continued use of the Service.
(1) Acts for commercial purposes or gain
(2) Use of the account name or password of his own or
any third parties for improper purposes
Also, Users shall be solely responsible for managing
and using their registered user account names
and passwords. In no event can we accept any
responsibility for any problems or damages resulting
from the User’s management and usage of its user
account name and password management.
(3) Infringement or acts that may likely infringe on
the intellectual property rights of third parties
(including but not limited to copyrights, design
rights, patent, utility model rights, trademark, trade
secrets, and know-how)
2. Period for the Service
(4) Infringement or acts that may likely infringe on the
proprietary rights, honor, trustworthiness, portrait
rights, privacy, publicity rights, and other rights or
profits
Users may in principal continue to use the Service
as long as it is being provided by us. However, the
Service may be changed, suspended or cancelled at
our option without prior notice.
(5) Dissemination or distribution or acts that may likely
constitute dissemination or distribution of contents
that may be offensive to public orals and morals, or
defamatory to third parties
3. Disclaimer
The User shall undertake use of the Service at its own
individual responsibility, and accordingly we shall not
assume any responsibility for usage of the Service by
the User, including but not limited to the examples
as follows.
(6) Criminal acts, acts associated with criminal acts, or
acts that may likely be criminal
(7) Dissemination or distribution of junk mail, spam or
malicious programs such as the computer viruses
(1) We shall make no warranty as to completeness,
legality, moral correctness, recentness, and
appropriateness of the Service and the User shall
assume full risk and individual responsibility for
using the Service.
(8) Dissemination or distribution of false information
(9) Obstruction or acts that may likely constitute
obstruction of the operation of the Service
34 ñ EnDgoliwsnhload from Www.Somanuals.com. All Manuals Search And Download.
(10)Acts that cause or that may likely cause trouble,
disadvantages or damages to us or third parties
9. User Information
In order to take advantage of the Service, the User
must first register user account name, password,
the User’s valid e-mail address and arbitrary
(11)Use of the Service for illegal purposes
(12)Other acts deemed inappropriate by us
User’s information via the next page (collectively
“Information”). We shall properly manage and keep
Information as important data in conformity with
our “Privacy Policy” and shall only use Information for
issuing notices regarding completion of registration,
maintenance of Service, suspension of Service, and
procedures for reissuance of passwords. We shall not
disclose Information for any purposes other than the
foregoing without the prior consent of the User.
5. Compensation Claim
Should any complaints, lawsuits or similar claims be
asserted against us by other Users or third parties for
any reasons attributable to the User in connection
with the Service, we reserve the right to claim from
the concerned User any damages, costs and expenses
which we may incur (including compensation,
attorney fees and legal costs).
6. Ownership of Intellectual Property Rights
10. Governing Law
All intellectual property rights (including but not
limited to copyrights, design rights, patent, utility
model rights, trademark, trade secrets, and know-
how), the portrait rights, privacy, publicity rights
and other personal rights, and proprietary rights or
other property rights of the information, text, image,
program, layout, design, architecture, and others
related to the Service are owned by us, or provided
to us under license from the rights holder except for
the rights of the thing which are made by User. The
unauthorized copying, alteration, or sublicensing of
such intellectual property rights, in whole or in part,
without our consent may be prohibited by applicable
law.
The Agreement shall be governed by and construed
in accordance with the laws of Japan.
ÑAbout QAU0569 (USB Wi-Fi® Adapter)
The Wi-Fi Adapter is attached to this unit when
shipped from the factory. When the adapter is
removed, store it in a safe place.
Further, our trade names, trademarks, logo marks and
product names, some of which are registered, are
used as names and symbols for commercial purposes.
Also, trademarks, service names, symbols and other
marks belonging to other parties, such as companies
and individuals, are also included in the Service.
7. Use of Public Information
We may save and store all information (including but
not limited to text information, image information,
and others) that were released, posted, uploaded, or
saved by User via the Service. Furthermore, User shall
agree that we may use such information as described
previously in every possible condition toward smooth
operation and improvement of the Service.
8. Usage Fee
The Service shall be offered without charge to the
User. However, the environment that is necessary for
use this Service shall be prepared by User on his own
responsibility and liability including any miscellaneous
expenses such as provider, electricity, packet
communication, and others.
Download from Www.Somanuals.com. All Manuals Search And DowEnlnoagdli.sh ñ 35
DNN9150BTM / DNR8015BTM:
ÑThe marking of products using lasers
CLASS 1
LASER PRODUCT
Declaration of Conformity with regard to
the EMC Directive 2004/108/EC
Declaration of Conformity with regard to
the R&TTE Directive 1999/5/EC
Declaration of Conformity with regard to
the RoHS Directive 2011/65/EU
Manufacturer:
JVC KENWOOD Corporation
3-12, Moriyacho, Kanagawa-ku, Yokohama-shi,
Kanagawa 221-0022, JAPAN
EU Representative:
JVCKENWOOD NEDERLAND B.V.
Amsterdamseweg 37, 1422 AC UITHOORN, The
Netherlands
The label is attached to the chassis/case and
says that the component uses laser beams that
have been classified as Class 1. It means that
the unit is utilizing laser beams that are of a
weaker class. There is no danger of hazardous
radiation outside the unit.
ÑEski Elektrik ve Elektronik
Ekipmanların İmha Edilmesi Hakkında
Bilgi (ayrı atık toplama sistemlerini
kullanan ülkeleri için uygulanabilir)
Sembollü (üzerinde çarpı işareti
olan çöp kutusu) ürünler ev atıkları
olarak atılamaz.
English
Hereby, JVC KENWOOD declares that this unit
DNN9150BTM/ DNR8015BTM is in compliance
with the essential requirements and other
Eski elektrik ve elektronik
ekipmanlar, bu ürünleri ve ürün
atıklarını geri dönüştürebilecek
bir tesiste değerlendirilmelidir.
Yaşadığınız bölgeye en yakın
geri dönüşüm tesisinin yerini
öğrenmek için yerel makamlara
müracaat edin. Uygun geri
relevant provisions of Directive 1999/5/EC.
Türkçe
Bu vesileyle JVC KENWOOD, DNN9150BTM/
DNR8015BTM ünitesinin, 1999/5/EC Direktifinin
başlıca gereksinimleri ve diğer ilgili hükümleri
ile uyumlu olduğunu beyan eder.
dönüşüm ve atık imha yöntemi
sağlığımız ve çevremiz üzerindeki
zararlı etkileri önlerken kaynakların
korunmasına da yardımcı olacaktır.
For Turkey
Bu ürün 28300 sayılı Resmi Gazete’de
yayımlanan Atik Elektrikli ve Elektronik Eşyalarin
Kontrolü Yönetmeliğe uygun olarak üretilmiştir.
Download from Www.Somanuals.com. All Manuals Search And Download.
|