Hardware description
The Digital Projector Mount utilizes the following hardware. Note that the letters associated with the hardware
on this list correspond to the letters listed in the instructions for each installation method.
A. Four (4) 4 (mm) x 10 (mm) Phillips head screws (supplied)
27700B S.W. Parkway Ave.
Wilsonville, Oregon 97070-9215
1-800-294-6400
SP-CEIL-008 DIGITAL PROJECTOR MOUNT
Installation Instructions
B. One (1) mounting bracket (supplied)
These are the installation instructions for your Digital Projector Mount. Included are four methods of
installation.
Select the method that works best for your viewing situation. The methods are:
°
°
Fixed Height Ceiling Installation— best for short ceilings, eight (8’) or lower
Adjustable Height Ceiling Installation—best for high ceilings, nine (9’) feet or higher
(optional) SP-LTMT-EXTP-S height adjustable extension is required.
C. Digital Projector (not included)
D. One (1) Litemount Plus® assembly (supplied)
°
Wall Mount Installation—for installing the Digital Projector Mount on a rear wall the
(optional) SP-LTMT-EXTP-S height adjustable extension is required.
NOTE: If the required height range is greater than 12½", the optional SP-LTMT-EXTP could be used to
extend the length of the suspension adapter. For further information or ordering assistance, please contact us
at the phone number and address listed at the top of this column.
Before You Start the Installation
The wall or ceiling where you want to install the digital projector must be capable of supporting a weight that is
five (5) times the weight of 7lbs the projector you are installing. Consult the projector’s documentation for
weight specifications. If the wall, ceiling, tabletop, shelf, or floor is not strong enough to handle five (5) times
the weight of 7lbs, then you must reinforce the installation environment. If you are unsure about the
installation environment, please consider having it reinforced and having the projector installed by qualified
personnel. Failure to do so could result in serious personal injury and damage to the projector.
NOTE: Hardware item (E) is what secures the Digital Projector Mount to your ceiling, wall, tabletop, floor.
Make sure you consult with your local hardware store staff for the type of hardware that works best for your
installation environment.
E. SINGLE WOOD STUD: If mounting on a single wood stud use three (3) #14 x 2" Lag bolts (minimum)
commercially available. Use the mounting points on the center of the plate as indicated in the assembly
diagram.
To avoid personal injury, use only an approved projector mount. Using an unauthorized projector mount may
lead to poor ventilation and projector failure.
° SOLID STRUCTURE: If mounting to a solid structure use four (4) 5/16" x 2" Lag bolts or commercially
available hardware (depending on the installation requirements). Use the mounting points found on the outer
points of the mounting plate as indicated in the assembly diagram.
When installing the projector mount, keep in mind that the projector’s focus ring is not squarely in the center
of the front of the projector, but offset by several inches. Make sure that when you mount the projector you
offset the installation to match the amount of inches that the projector’s focus ring is offset from the center of
the front of the projector.
F. Allen wrench (supplied)
R
LISTED
E176225
Copyright by InFocus Corporation
Wilsonville, OR. All rights reserved
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Wood stud
E
Adjustable Height Ceiling Installation
Complete the following steps to install the projector mount and projector on your ceiling with the optional
suspension adapter.
Ceiling structure
Center of wood stud
This installation works best with high ceilings (FIGURE 3).
D
Note: Look at the bottom of the upper assembly (D) and locate the arrow. Make sure you install the projector
mount with the arrow pointing toward your screen.
6.
7.
Use the Allen wrench (F) to remove the upper plate from the mount assembly (D).
Use the Allen wrench to remove the two screws from the enclosed end of the of the suspension
adapter, and place it into the slotted extension on the upper plate (E). Make sure that the two (2) outer
holes on the suspension adapter align with the holes on the slotted extension on the upper plate.
8.
9.
Replace the two screws removed in step 2 into the two (2) holes to secure the suspension adapter to
the upper plate.
Attach the mount assembly to the suspension adapter and secure them with the two screws removed
in step 1.
C
Insert and rotate 180°
and lock down
10. Secure the upper assembly to the ceiling using the commercially available hardware (E) suitable for
your environment. Be sure that the upper assembly arrow is pointing toward your screen.
11. Carefully raise the projector (C) with the mounting bracket (B) attached and insert it into the bottom of
the upper assembly (D) by its tabs.
12. Rotate the projector (C) with the mounting bracket (B) attached 180º so that the projector’s focus ring
is pointing toward your screen.
13. Align the safety knob on the mount assembly with the end of the arrow-shaped slot on the mounting
B
bracket (B) and screw it through the opening to prevent further rotation. Hand-tighten the safety knob.
14. Hand-tighten the remaining two tension knobs to secure the mounting bracket to the amount
assembly.
A
C
CAUTION: Check all of the hardware for proper tightness and security. Do not over-tighten the screws.
SEE FIGURE 3
Solid ceiling structure
NOTE: Use the Allen wrench key (F) for the following modification
D
E
C
Insert and rotate 180°
and lock down
B
C
A
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Wood stud
FIGURE3
E
Ceiling plate
Ceiling structure
Remove
from mount
assembly
Center of wood stud
Adjustable screws
Remove
from mount
assembly
D
Optional
SP-LTMT-EXTP-S
extension adapter
Ceiling plate
C
Insert and rotate 180°
and lock down
Mount
assembly
B
A
Replace the
hardware
C
Solid ceiling structure
Optional
SP-LTMT-EXTP-S
extension adapter
D
E
Adjustable screws
Optional
SP-LTMT-EXTP-S
extension adapter
Adjustable screws
WARNING
When using the optional
extension adapters and making
a height adjustment while
secured to the wall or ceiling do
not remove the screws
completely from the extension.
Failure to do so could result in
injury and damage to the
projector.
Replace the
hardware
Insert and rotate 180°
and lock down
C
B
C
A
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Wall Mount Installation
Complete the following steps to install the projector mount and projector to your wall. (FIGURE 4)
Wall wood stud
Wall structure
Note: Look at the bottom of the upper assembly (D) and locate the arrow. Make sure you install the projector
mount with the arrow pointing toward your screen.
Top plate
NOTE: Follow step 3 to secure the extension to the mount assembly.
15. Secure the upper plate to the wall using the commercially available hardware (E) suitable for your
environment. Be sure that the screen indicator arrow is pointing toward your screen.
16. Carefully raise the projector (C) with the mounting bracket (B) attached and insert it into the bottom of
Optional
SP-LTMT-EXTP-S
extension adapter
the mount assembly by its tabs.
17. Rotate the projector (C) with the mounting bracket (B) attached 180º so that the projector’s focus rings
E
is pointing toward your screen.
18. Align the safety knob on the mount assembly with the end of the arrow-shaped slot on the mounting
Adjustable screws
bracket (B) and screw it through the opening to prevent further rotation. Hand-tighten the securing
knob.
19. Hand-tighten the remaining two tension knobs to secure the mounting bracket (B) to the mount
assembly (D).
B
CAUTION: Check all of the hardware for proper tightness and security. Do not over-tighten the screws.
SEE FIGURE 4
NOTE: Use the Allen wrench key (F) for the following modification
C
B
WARNING
C
When using the optional
extension adapters and making
a height adjustment while
secured to the wall or ceiling do
not remove the screws
completely from the extension.
Failure to do so could result in
injury and damage to the
projector.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
|