Stiga Lawn Mower 100 B User Guide

STIGA PARK  
100 B  
8211-3014-08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GB  
ENGLISH  
7b. Park 2000-  
SYMBOLS  
Hook the tension roller spring H into the fastener,  
just behind the front right wheel (fig 2).  
The following symbols are displayed on the ma-  
chine in order to remind you about the safety pre-  
cautions and attention necessary when using the  
machine.  
8. Lift up the mower deck and hook the spring on  
the implement lifting bar.  
When changing the v-belt or removing the mower  
deck, proceed in the reverse order.  
The symbols mean:  
Warning!  
Read the instruction and safety manual be-  
fore using the machine.  
ADJUSTING  
1. Make sure that the tyres have the correct inflation  
pressure:  
Front: 0,6 bar (9 psi).  
Warning!  
Do not put hands or feet under the cover of  
the machine when it is running.  
Rear: 0,4 bar (6 psi).  
2. Stand the machine on a level floor. Slacken the  
screws K and adjust the mower deck so that the  
front and rear edges L come at the same distance  
from the floor (fig 3). Tighten the screws.  
Warning!  
Beware of objects being flung out. Keep  
spectators away.  
Points 1 and 2 must be carried out to ensure that the  
mower deck mows evenly.  
Warning!  
Beforestarting any repair work, remove the  
spark plug cable from the spark plug.  
USE  
MOWING HEIGHT  
The mower deck has 5 fixed mowing heights, from  
40 mm to 80 mm.  
ASSEMBLING  
MOWER DECK  
N.B. The stated mowing heights apply when the  
machine is standing on firm ground.  
1. Fit the attachments D on the front axle projections  
by means of washers and locking clips (fig 1).  
MOWING HINTS  
2. Fit the attaching arms of the mower deck on the  
attachments on the machine.  
For the best effect follow this advice:  
- mow regularly.  
- use full throttle on the engine.  
- keep the underside of the mower deck clean.  
- use sharp blades.  
3. Place on the v-belt between the belt pulley of the  
mower deck and the centre belt pulley F of the ma-  
chine (fig 2).  
- do not mow wet grass.  
4. The tensioning roller G should come on the left  
side of the belt as viewed from the driving seat (fig  
2)  
MAINTENANCE  
5. Then pull the mower deck forwards so that the  
holes in the attaching arms come in line with the  
holes in the attachments on the machine.  
Neither the motor nor the mower deck  
may be serviced unless:  
- the motor is shut off.  
- the ignition key is removed.  
- the ignition cable is removed from the  
spark plug.  
- the parking brake is engaged.  
- the mower deck is disengaged.  
6. Fit the bolts and tighten them.  
7a. Park -1999:  
Hook the tension roller spring H into the floor on  
the right-hand side (fig 2).  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
GB  
ENGLISH  
When the blades are due to be sharpened, the wet  
grinding method with a waterstone or grindstone is  
to be used.  
CLEANING  
Each time after mowing wash off the underside of  
the mower deck casing with a garden hose.  
Following sharpening, the blades must  
be balanced to avoid vibration damage.  
If grass has dried on, remove the mower deck and  
scrape the underside clean.  
If necessary, touch-up the underside with paint to  
avoid rusting.  
CHANGING BLADES  
Always use original spare parts when changing the  
blades, blade attachments or bolts.  
CHANGING DRIVE BELT BETWEEN  
CENTRE BELT PULLEY AND MOW-  
ER DECK  
Always use original spare parts. Using  
non-original spare parts can result in  
the risk of damage even if they fit in the  
machine.  
1. Unhook the tension roller spring H (fig 2).  
2. Unbolt the mower deck from the machine.  
3. Push in the deck towards the machine.  
When changing the blades, the blades central bolt  
should also be replaced. It is provided with a lock-  
ing device. The blade bolts torque: 65 Nm.  
4. Change the faulty v-belt. Always use a genuine  
belt. The tensioning roller G should come on the  
left side of the v-belt as viewed from the driving  
seat (fig 2).  
SPARE PARTS  
STIGA original spare parts and accessories are  
constructed exclusively for STIGA machines.  
Note that non original spare parts and accessories  
have not been checked or approved by STIGA.  
5. Bolt the mower deck on the attachments on the  
machine.  
6a. Park -1999:  
Hook the tension roller spring H into the floor on  
the right-hand side (fig 2).  
Usage of such parts and accessories can  
influence the machines operability and  
safety. STIGA cannot be held responsi-  
ble for injuries caused by these prod-  
ucts.  
6b. Park 2000-  
Hook the tension roller spring H into the fastener,  
just behind the front right wheel (fig 2).  
CHANGING DRIVE BELT IN MOWER  
DECK  
1. Remove the mower deck from the machine.  
2. Remove the transmission casing over the mower  
deck.  
3. Release the spring M which holds the tensioning  
roller (fig 4).  
4. Change the v-belt and assemble in the reverse  
order. Always use a genuine belt.  
BLADES  
Make sure the blades are always sharp. This gives  
the best mowing results.  
SHARPENING  
For safety reasons the blades must not be sharp-  
ened on an emery wheel. Incorrect sharpening (=  
high temperature) can result in the blades becom-  
ing brittle.  
STIGA reserves the right to modify the product without  
prior notice.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
M O W I N G A H E A D  
BOX 1006 · SE-573 28 TRANÅS  
w w w.s t iga.co m  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Cub Cadet Lawn Mower 190 190 100 User Guide
Land Pride Lawn Aerator CA25 User Guide
Scag Power Equipment Lawn Mower STHM 59999 User Guide
Scag Power Equipment Lawn Mower STT 25CH LP User Guide
Snapper Lawn Mower 13HP User Guide
Snapper Lawn Mower MCRP215014KWV User Manual
Snapper Lawn Mower RT1330E User Manual
Snapper Lawn Mower V180 User Manual
Swisher Lawn Mower T1260 T1360 User Guide
Troy Bilt Lawn Mower 11A 436N063 User Guide