OWNER’S
MANUAL
FROM SERIAL #96-
354001 TO L199-307000
MODEL NO.
T1260
T1360
60” UNIVERSAL
TRAILMOWER
Assembly
Operation
Service and Adjustment
Repair Parts
Rev.05-193
Made In The
P.O. BOX 67, WARRENSBURG, MISSOURI 64093 PHONE 660-747-8183 FAX 660-747-8650
Manufacturing quality lawn care equipment since 1945
USA
10829
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Exercise special care when mowing
around fixed objects in order to prevent
the blades from striking them. Never
deliberately run mower onto or over any
foreign object.
Safety Rules
Safe Operation Practices for Trailmowers
Important: This cutting machine is capable of
amputating hands and feet, and throwing
objects. Failure to observe safety
instructions could result in serious injury or
death.
•
•
Use mower only as the manufacturer
intended and as described in the manual.
Do not operate the mower if it has been
dropped or damaged in any manner.
Always have damage repaired before
using your mower.
•
•
Always wear safety glasses or eye
shields when starting and while using
your mower.
Dress properly. Do not operate mower
when barefoot or wearing open sandals.
Wear only solid shoes with good traction
when mowing.
Always make cutting height adjustments
before starting your mower. Never
attempt to do this while the engine is
running.
Keep your eyes and mind on your mower
and the area being cut.
Do not let other interests distract you.
Do not put hands or feet near or under
rotating parts. Keep clear of the
discharge opening at all times.
Before cleaning, inspecting, or repairing
your mower, stop the engine and make
absolutely sure the blade and all moving
parts have stopped. Then disconnect the
spark plug wire and keep it away from
the spark plug to prevent accidental
starting.
Do not operate your mower if it vibrates
abnormally. Excessive vibration is an
indication of damage: stop the engine,
safely check for the cause of vibration
and repair as required.
I.
General Operation
•
•
Read, understand, and follow all
instructions in the manual and on the
machine before starting.
Read this operator’s manual carefully.
Become familiar with the controls and
know how to operate your mower
properly.
Only allow responsible adults, who are
familiar with the instructions, to operate
the machine.
Clear the area of objects such as rocks,
toys, wire, etc. which could be picked up
and thrown by the blade.
•
•
•
•
•
•
•
Be sure the area is clear of other people
before mowing. Stop machine if anyone
enters the area.
•
•
•
Never carry passengers.
Do not mow in reverse unless absolutely
necessary. Always look down and behind
before and while backing.
Be aware of the mower discharge
direction and do not point it at anyone.
Do not operate mower without the guards
in place.
•
•
•
•
•
Slow down before turning.
Never leave a running machine
unattended. Always turn off blades and
stop engine.
Turn off blades when not mowing.
Mow only in daylight or good artificial
light.
Never operate your mower without
proper guards, plates, or other safety
devices in place.
•
•
II.
Slope Operation
•
•
•
Do not operate the machine under the
influence of alcohol or drugs.
Watch for traffic when operating near or
crossing roadways.
Use extra care when loading or
unloading the machine into a trailer or
truck.
Slopes are a major factor related to loss-of-
control and tip over accidents, which can result in
severe injury or death. All slopes require extra
caution. If you feel uneasy on it, do not mow it.
DO:
•
•
Mow up and down slopes.
Remove obstacles such as rocks, tree
limbs, etc.
•
•
Do not attempt to operate the tow vehicle
when not in the driver’s seat
Disengage power to mower, stop engine
when transporting or not in use.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
•
•
Watch for holes, ruts or bumps. Uneven
terrain could overturn the machine. Tall
grass can hide obstacles.
Use slow speed. Choose a low gear so
that you will not have to stop or shift
while on the slope.
Keep all movement on the slopes slow
and gradual. Do not make sudden
changes in speed or direction.
Avoid starting or stopping on a slope. If
tires lose traction, disengage the blades
and proceed slowly straight down the
slope.
IV. Service
•
Use extra care handling gasoline and other
fuels. They are flammable and vapors are
explosive.
o Use only an approved container.
o Never remove gas cap or add fuel
with the engine running.
o Allow engine to cool before refueling.
Do not smoke.
o Never refuel the machine indoors.
o Never store the machine or fuel
container where there is an open
flame, such as a gas water heater.
Never run a machine inside a closed area.
Keep nuts and bolts, especially blade
attachment nuts, tight and keep equipment in
good condition.
•
•
DO NOT:
•
Do not turn on slopes unless necessary,
And then turn slowly and gradually
downhill if possible.
•
•
Never tamper with safety devices. Check
their proper operation regularly.
Keep machine free of grass, leaves, or other
debris build-up. Clean oil or fuel spillage.
Allow machine to cool before storing.
Stop and inspect the equipment if you strike
an object. Repair if necessary before
restarting.
•
Do not mow near drop-offs, ditches or
embankments. The mower could
suddenly turn over if a wheel is over the
edge of a cliff or ditch, or if an edge
caves in.
•
•
•
Do not mow on wet grass. Reduced
traction could cause sliding.
Mower blades are sharp and can cut. Wrap
the blade(s) or wear gloves, and use extra
caution when servicing them.
III. Children
Caution:
Tragic accidents can occur if the
operator is not alert to the
presence of children. Children
are attracted to the machine and
the mowing activity. Never
assume that children will remain
where you last saw them.
Look for this symbol to point out
important safety precautions. It
means CAUTION!!! BECOME
ALERT!!! YOUR SAFETY IS
INVOLVED!!!
•
Keep children out of the mowing area
and under the watchful care of another
responsible adult.
•
•
•
Be alert and turn machine off if children
enter the area.
Caution:
Always disconnect spark plug
wire and place it where it cannot
contact the spark plug in order to
prevent accidental starting when
setting up, transporting, adjusting
or making repairs.
Before and when backing, look behind
and down for small children.
Never carry children. They may fall off
and be seriously injured or interfere with
safe machine operation.
Never allow children to operate the
machine.
Use extra care when approaching blind
corners, shrubs, trees or other objects
that may obscure vision.
•
•
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY AND OPERATIONAL DECALS
Replace decal immediately if damaged. Order by part number from
Swisher Mower and Machine Co. Inc.
OD42 Warning Decal
OD43 Danger Decal
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY AND OPERATIONAL DECALS
OD
OD
OD
OD
46 Speed Decal
49 Engine Power Decal
OD
OD
6
Download from Www.Somanuals.com. All Manuals Search And Download.
OperatingYour NewMower
Theoperation of anymower canresult inforeign objects being thrown intothe
eyes, which can result insevere eye damage. Always wear safety glasses or eye
shields beforestarting your mower and while mowing. Werecommend wide vision
safetymask for over the spectacles or standard safety glasses.
Caution:
Tragic accidents can occur if theoperator is not alert to the presence of children.
Children areattracted tothe machineandthemowing activity. Never assume that
children will remainwhere youlast sawthem.
Stopping
StartingtoMow
•
•
Movebladeclutch lever to disengageposition.
Turnkeyswitchto theOFFposition.
•
•
•
•
Adjust mower cutting height.
Start mower engine.
Movethrottleto RUNposition.
Movemower bladeclutch lever tothe engaged
position tostart mower blades.
AttachingMower toTowVehicle
•
•
•
•
Place mower behindtractor and back tractor up
toit for attaching.
Slide towbar of mower over tractor drawbar so
that holes line up.
Insert hitch pinuntil it extends throughthe
bottomof thetowbar.
Place safety latch over end of thehitchpin. The
red tether is usedtomanuallydisengage the
blades innormal operation, andautomatic
disengagethe blades if the towvehicle
becomes separatedfromtheTrailmower.
Ablack tether is usedto manually engage the
blades of theTrailmower without leavingthe
operator position.
Caution:
Never operate themower without
dischargechutecover in
the
place.
Mower Height Adjustment
•
•
Caution:
Shut off mower andremove
spark plug wire beforemaking
any adjustments tothe mower.
It is important that yousecurelyattachboth
thebladeengage anddisengagetether to
thetowvehicle.
Caution:
•
•
Themowing height range is approximately1-
1/2to 4-1/2 inches. Theheights aremeasured
fromtheground tothe bladetip withthe engine
not running.
Never operatethis mower
without both safetytethers
securely attached to thetow
vehicle.
The average lawn should becut to
approximately2-1/2 inches duringthecool
seasonand toover 3 inches during hot months.
For healthier and better-lookinglawns, mow
oftenandafter moderategrowth.
For best cutting performance, grass over 5
inches inheight shouldbe mowedtwice. Make
thefirst cut relativelyhigh, thesecondto
desired height.
TransportingYour Mower
•
•
•
Disengage blades.
Shut off mower engine.
Place mower deck inthehighest cutting
position.
•
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Caution:
Caution:
Shut off mower and remove
spark plug wire before making
any adjustments to the mower.
Shut off mower and remove
spark plug wire before making
any adjustments to the mower.
Cutting Height Adjustments
•
•
•
Rotate height adjust crank handles (item #8
and #5 in fig. 4) in a clockwise direction to
raise the mower and in a counter-clockwise
direction to lower.
Make sure that height adjustment is the same
on both sides of the mower, as indicated by
the graduated scales on the height
adjustment tubes.
Tow Hitch Offset Assembly
•
Please refer to figure 2 for the assembly of
the hitch bar.
Before Starting Engine
•
Fill engine with oil. (See engine manual for
proper procedure and requirements.)
Add gasoline. Fill tank using fresh clean
unleaded gasoline.
•
NOTE: Graduated scales are for reference
only.
Front to Back Adjustment
Caution:
To obtain the best cutting results, the mower housing
should be adjusted so that the front is approximately
¼” to ¾” lower that the rear. To check for front to
back adjustment, measure from the bottom edge of
the deck to the ground at both the front and rear of
the deck.
Fill to bottom of fuel tank filler
neck. Do not overfill; wipe off
spilled oil or fuel. Do not store,
spill or use gasoline near open
flame
To Start Engine
Tow Hitch Offset Assembly
This Trailmower has been designed to run offset from
the center of the tow vehicle to provide additional
cutting width. (Refer to fig. 2 for assembly
information)
Caution:
Keep the blade clutch lever in
“Disengaged” position when
starting engine
•
The adjustable tow hitch of this mower can
be assembled in several positions from
straight to 58” offset to either side.
•
•
Make sure spark plug wire is properly
connected.
•
We recommend when towing with a tow
vehicle equipped with a mid mount mower to
offset the Trailmower to overlap the cut of
the mid mount mower by 6”. This will need to
be adjusted depending on the type of terrain,
obstacles, and the tow vehicle being used.
If your tow vehicle is not equipped with a mid
mount mower the hitch can be adjusted to a
straight position, but we recommend using
the offset position to eliminate grass being
crushed by the tow vehicle.
Place throttle control in “Choke” position if the
engine is cold. A warm engine may not
require choking to start.
•
•
•
Turn key to start position. Release key
immediately when engine starts.
When engine starts, move throttle control to
the “Run” position. (Full throttle)
Allow engine to warm up for a few minutes
before engaging blades.
•
NOTE: If at high altitude (above 3000 ft) or in cold
temperatures (below 32° F), the carburetor fuel
mixture may need to be adjusted for best
performance. (See service and adjustments
section of engine manual.)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Breaking in Your Mower
Suggested Mowing Practices
Break in your belts, pulleys, and engine before you
actually begin mowing.
•
Mowing should be started with tractor in low
gear and speed increased only as mowing
conditions will safely permit. This speed
should not exceed 3-1/2 MPH.
•
Start engine, engage blade control to start
blades rotating and allow blades to rotate for
approximately five minutes to break in mower
and engine.
•
Better mowing results will be obtained in
grassy areas if they are mowed when the
grass is approximately 4-5” maximum height.
While your mower will cut grass taller than 5”,
you will experience a substantial increase in
the horsepower required and some change in
finished appearance of the area mowed.
Mowing conditions will vary from place to
place, including the types of grass that are
being mowed, such as fine stalk, coarse
stalk, dense or sparse grasses. When
mowing tall grass, you may find that the
pressure of wheel tracks may cause certain
grasses to be pushed downward and will not
be mowed properly. If this condition exists,
you may have to mow the area twice, the first
mowing with the mower raised and the
second at the normal height you have
chosen. If it is practical, better results will be
found if the second mowing is at a right angle
in travel to the previous mowing.
Caution:
Shut off mower and remove
spark plug wire before making
any adjustments to the mower.
•
•
•
Do not mow grass when it is wet. Wet grass
will accumulate under the mower deck and
leave undesirable clumps. Allow grass to dry
before mowing.
Always operate mower at full throttle when
mowing to assure better mowing
performance and proper discharge of
material. Regulate ground speed by selecting
a low enough gear to give the mower cutting
performance as well as the quality of cut
desired.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Mower Maintenance
General Recommendations
•
•
•
To remove blade for sharpening, use wooden
The warranty on this Trailmower does not cover items
that have been subjected to operator abuse or
negligence. To receive full value from the warranty,
operator must maintain unit as instructed in this
manual.
block to hold blade while removing the blade-
mounting nut. The nuts have right hand
threads.
When grinding, care should be taken to
maintain blade balance and the blade should
be checked for proper balance before
reinstalling on mower.
Some adjustments will need to be made periodically
to properly maintain your unit.
Check and balance. File material off heavier
end of blade until it is balanced.
To ensure satisfactory operation, it is
recommended that before the start of each
mowing season, the old blades be discarded and
replaced with new blades.
All adjustments in the service and adjustments
section of this manual should be checked at least
once each season.
Before Each Season
NOTE: Check nuts and blades occasionally to
make sure nuts are tight.
•
•
•
Replace the spark plug.
Clean or replace the air filter.
Check blades and belts for wear.
Caution:
A new spark plug and clean air filter assure
proper air-fuel mixture and help your engine run
better and last longer.
Shut off mower and remove
spark plug wire before making
any adjustments to the mower.
Before Each Use
•
Check engine oil level. (Do this twice to
ensure an accurate reading.)
Check blade operation.
Cleaning the Mower
Water pressure from a garden hose will remove fresh
clippings from the underside of the mower. Clean
mower after each use.
•
•
Check for loose fasteners.
Daily Maintenance
Repair Parts
Make sure all nuts and bolts are tight, cotter pins
and retainer clips are secure. Keep blades sharp.
Observe all safety precautions.
Your Trailmower has been produced with
components designed for your unit. Although
standard V-belts, bearings, blades, pulleys, etc. may
look like parts used on your rotary mower, and while
similar in appearance, many are of a different
construction and could in some cases cause a
malfunction in the operation of the machine.
Blade Care and Service
For best results, mower blades must be kept sharp.
The blades can be sharpened with a few strokes of a
file or on a grinding wheel. Do not attempt to sharpen
while on mower.
For continued satisfactory performance, use only
repair parts supplied by the manufacturer. See your
SWISHER dealer for replacment parts.
Caution:
Do not handle mower blades
with bare hands. Careless or
improper handling may result in
serious injury.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
LEFT
RIGHT
BLADE DRIVER
ASSEMBLIES (Prior
to 97-231001)
NB175 (A108)
NB175 (A108)
AS155
AS155
6104
6104
FIGURE 1A
6104RS
NB179
(B104W)
B98
NB179 (B104W)
B98
B99
B99
B100LS
B98
B100S
B98
CENTER
NB175 (A108)
AS155
687
NB179 (B104W)
B98
B9960
Blade Driver Assemblies
Center – B99CCS
Left – B99CLS
B100CS
B98
Right – B99CS
B98W
B108LB
B102
660S – single
660 – set (3)
Same for all three blade
driver positions
B102
B108L
B108
For a complete set
(minus the blade) for
one blade driver order
B100SK
11
Download from Www.Somanuals.com. All Manuals Search And Download.
LEFT
RIGHT
BLADE DRIVER
ASSEMBLIES (After
97-231001)
NB175 (A108)
NB175 (A108)
AS155
AS155
6114
6114
FIGURE 1B
6104RS
NB179
(B104W)
B98
NB179 (B104W)
B98
CENTER
NB175 (A108)
B99
B99
AS155
B100LS
B98
6114CS
B100S
B98
6114
687
NB179 (B104W)
B98
B9960
Blade Driver Assemblies
Center – B99CCS
Left – B99CLS
B100CS
B98
Right – B99CS
B98W
B108LB
B102
660S – single
660 – set (3)
Same for all three blade
driver positions
B102
For a complete set
(minus the blade) for
one blade driver order
B100SK
B108L
B108
12
Download from Www.Somanuals.com. All Manuals Search And Download.
H11
H11
H10
661
H11
H11
662
661A
Hitch Bar Assembly
Figure 2
Brown
M
S
B
Green
Kill
G
L
Key Switch
Battery
Red
Black
Red
Red
Red
To Alternator
Solenoid
T60 12V Start
Figure 3
13
Download from Www.Somanuals.com. All Manuals Search And Download.
04
02
05
03
06
01
08
07
52
53
09
10
08
11
12
14
13
15
Figure 4
14
Download from Www.Somanuals.com. All Manuals Search And Download.
16
19
17
18
20
22
21
16
23
21
20
25
24
24
26
Figure 5
15
Download from Www.Somanuals.com. All Manuals Search And Download.
28
27
27
18
22
23
27
27
28
29
Figure 6
16
Download from Www.Somanuals.com. All Manuals Search And Download.
OBSOLETE PART
NUMBERS ARE SHOWN
IN (
) AND ARE FOR
NB122 (665N)
NB195 (665TW)
REFERENCE ONLY
B98
NB195 (665BW)
665 + Color Code
663S
NB121 (T2K)
F4157WR
CB58
691
F4157WV
CB58
NB151 (670)
F4157WT
663L
NOTE: F4157WF 13X500X6
contains Wheel, Tire and
Bearings
CASTER ASSEMBLY
Figure 7
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Item #
Description
Grass Chute
Part #
(CH5) 6031TK
(CH5B) NB136
CH5S
1
Bolt/Nut
Spring
2
3
Tire/Wheel/Bearing
Right Belt Guard
Acorn Nut
F4157W
6155RN
(FR154N) NB120
BCSR
4
5
Battery Cable Red
Battery Cable Black
Height Adjust Crank Assembly
Height Adjust Crank
Plastic Bushing
Cotter Pin
BCS
H7ASY
H7N
T2PB
(T218C) NB580
H7K
Knob
5/16 Pal Washer
Threaded Link to the Deck (Not
included in Hgt Adj Assembly)
Left Belt Guard
Acorn Nut
NB117
(674S) 10038
6
7
6155LN
(FR154N) NB120
6102T
Gas Tank
Gas Cap
6102NC
6102TK
AS119
AS120
6FLC
6102FLN
H7ASY
H7N
T2PB
Gas Tank Mount
Rubber Bushing
Fuel Shutoff Valve
Fuel Line Clamp
Fuel Line
8
Height Adjust Crank Assembly
Height Adjust Crank
Plastic Bushing
Cotter Pin
(T218C) NB580
H7K
Knob
5/16 Pal Washer
Threaded Link to the Deck (Not
NB117
(674S) 6599
included in Hgt Adj Assembly)
Tire/Wheel/Bearing
Bolt/Nut
9
F4157WF
(670/T2K) NB151/NB121
663S
Spacer (Exterior)
Spacer (Exterior)
Spacer (Interior)
Caster Fork
663L
691
665TK
10
Caster Nut
Washer Upper
Washer Lower
(665N) NB122
(665TW) NB195
(665BW) NB195
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Item #
Description
Tongue
Part #
661
11
Tongue Hinge
Tongue Extension
Hitch Swivel
661A
662
H10
12
13
14
15
Safety Hitch Pin
Red Safety Rope
Blade Engage Tether (Black)
Blade Engage Lever T60
Engage Bushing
Bolt/Nut
H11
H9B
BT44
BEA60
(681S) 6713
(681B) NB155/NB281
Lever
681N
Lever Knob
B19 BLACK
Rod Spring
B25RT
16
Belt
66LR
Belt after Ser. 97-231001
Key Switch
66LR2
KS12
17
18
19
Blade Driver Center
Throttle
B99CCS (for list see fig. 1A or 1B)
686
Throttle after Ser. 97-231001
Idler Bracket
686N
678
B527
B99CS
20
21
22
23
24
25
Idler Pulley
Blade Driver Right
Blade Driver Left
Idler Rod Spring
Idler Pulley
B99CLS
B25R6 center / B25RT outer
B527
Engine Idler Bracket
Engine Belt
Anti-Scalp Roller
Bolt/Nut
Anti-Scalp Roller
Bolt/Nut
681N
644
SWR3
26
27
(BR4/BR47N) NB517/NB181
SWR3 - 2 Sets
(BR7/BR47N) NB147/NB181
664N
28
29
Rear Axle
Rear Wheel Washer
Cotter Pin
NB149
(T218C) NB580
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Items Not Shown
Description
Wiring Harness
Wiring Harness
Toggle Switch
Item #
Part #
WHN60B (Briggs)
WHN60T (Tecumseh)
685
30
31
Starter Relay
SOL NEW
9043
14A-A1
AS122
Starter Relay Ser. 97-98
Battery (12V) type
Oil Drain Valve
32
33
Oil Drain Hose
AS161
34
35
Engine Pulley
688
689L
689S
688K
Engine Pulley Spacer Long
Engine Pulley Spacer Short
Key Stock
36
37
38
39
40
41
Engine Pulley Washer
Engine Pulley Bolt
Bearing, Flanged 3/4 ID
Bearing, Flanged 5/8" ID 1 3/8" OD
Blade Bearing
699
(6100) NB452
CB58
F157B
B98
Decals and Labels
Warning Decal
42
43
44
45
46
47
48
49
50
51
OD30
OD29
OD36
OD20
OD33
OD11
OD10
OD28
OD32
OD31
OD56
OD57
Danger Decal
Caution-Deflector Decal
Caution Hand Decal
Speed Decal
No Step Decal
Blade Engage Decal
Engine Power Decal
Swisher Logo
Made in Missouri Decal
Throttle Decal
Console Decal
Additional Components
Engine Plate
52
53
6155NF
6155TH
Throttle Plate
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
23
Download from Www.Somanuals.com. All Manuals Search And Download.
60” UNIVERSAL
TRAILMOWER
OWNER’S
MANUAL
Each mower has its own model number. Each engine has its
own model number. The model number for the mower will be
found on the right rear corner of the frame. The model number
for the engine will be found on the top of the blower fan
housing.
All mower parts listed herein may be ordered directly from
Swisher Mower & Machine Co. Inc. or your nearest Swisher
dealer.
MODEL NO.
T1260
T1360
All engine parts may be ordered from the nearest dealer of the
engine supplied with your mower.
WHEN ORDERING PARTS, PLEASE HAVE THE
FOLLOWING INORMATION AVAILABLE:
* PRODUCT - TRAILMOWER
* SERIAL NUMBER - _______________
* MODEL NUMBER - _______________
* ENGINE MODEL NUMBER - _______________
TYPE - _______________
* PART NUMBER
* PART DESCRIPTION
TELEPHONE - 1-800-222-8183
FAX - 1-660-747-8650
SWISHER MOWER & MACHINE CO. INC.
1602 CORPORATE DRIVE P.O. BOX 67
WARRENSBURG, MO 64093
SWISHER MOWER & MACHINE CO. INC.
PRINTED IN U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|