INSTALLATION
INSTR UCTIONS
540 RPM FRONT
POWER TAKE-OFF (PTO)
MFG. NO. 1691351
KIT PARTS
1
I
existing hardware
Carrier installed inside
front tractor frame.
F i g u r e 1 .
Item
D
e
s
&
i
o
n
Item Description
Description
4
4
A ’
PTO Adaptor Assembly
PTO Housing Assembly
1’
F
G
H
Carrier
Frame
1
4
K
L
Capscrew,
Washer,
Lockwasher,
Nut,
2
4
M
C
D
E
Capscrew, 5/16-18x2-1/4
4
Washer,
Nut, Hex,
Nut. Jam,
‘N
Key, Woodruff
Plug, vent
1’
1
J
A
8 have been pre-assembled. Refer to
FORM
PRINTED IN U.S.A.
6711
1702133
Tractor Attachments Parts Manual for service
numbers.
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY DECAL
8. Install woodruff key (D) onto PTO shaft.
9. Install adaptor assembly (A) to housing input shaft.
Assembly should
easily
shaft and key.
Rotate PTO adaptor so that setscrew is at top of
shaft.
10. Just start PTO adaptor assembly (A) onto tractor
PTO shaft. Swivel back and forth in order to align
four capscrews (C) and spacers
carrier (F).
with holes in
l
Operate only with 540 RPM
attachments
I
11. Install washer (H) and hex
(I) and tighten fully.
Located on PTO Shield
With wrench on nut (I), install jam nut (J) and
tighten snug against hex nut.
12. To make
lift up on PTO housing (B) with
sliding adaptor back and forth. There should be
PTO adaptor (A) is properly aligned,
hand while
AS S E M BLY
1” play. When adaptor slides easily between both
shafts, hold PTO housing in position and tighten
1 .
Park tractor on a flat, level surface. Shut off engine,
key. and allow all moving parts to stop.
four
(K) securing carrier
to tractor
frame.
13. Remove setscrew from PTO adaptor (PTO housing
side) and push adaptor all the way towards tractor.
When Woodruff key (D) is visible (centered) in
setscrew hole, x-install setscrew and tighten.
W AR N I N G
has been in operation,
Use caution working around
muffler to cool befor e pr oceeding with installation.
may be hot.
allow
Remove shipping plug from PTO housing
check that gear oil is level with plug. Installvent plug
(E) when oil level is correct. Use POW oil as
and
N O T E
The initial assembly of PTO carrier (F,
frame is easier with hood deck removed
from tractor. To deck:
a. Tilt deck forward.
b. Uncouple headlight wiring harness.
Remove two
d. Remove hood deck from tractor.
to
REMOVAL
INSTALLATION
After initial assembly of PTO adaptor (A), housing
(B) and carrier (F), components should be left
assembled. Installation and removal can be
accomplished with four
hardware (L, M, N).
pins.
mounting
2. Remove PTO shield by removing spring clips and
bracket. Store spring clips with bracket.
2. Install
(K) only snug initially and repeat
alignment procedure (step 12).
3 . Install front
thru carrier(F) and install
washers (L), lockwasher (M), and nuts (N). Leave
hardware loose. Large washers
slotted frame holes only.
arc for front
Tighten snug
STORAGE
LUBRICATION
1. Store PTO assembly upright on frame to prevent
gear oil loss.
Install carrier onto
(K) and hardware
only until PTO is installed.
frame and install two
2. Check gear oil level every season by removing oil till
front side of PTO
level with plug opening. Do not till oil to vent plug
opening. Refer to 1.
Oil should be
5 . Apply oil or lubricant to splines of tractor PTO shaft.
6 . Remove existing bolts and nuts from PTO housing at
four locations shown in
2. Install
16-18 2-
3. Lubricate grease fittings on each side of PTO
housing (B) 25 hours of operation. Apply only
2-3 shots of standard automotive grease.
1/4
from front.
7. Install spacers (G) on end of
(C).
Download from Www.Somanuals.com. All Manuals Search And Download.
|