Harrier
48
CODE 485T
(Blade Brake Clutch - Auto Drive)
OWNER’S HANDBOOK
English Version
FROM SERIAL NO: 485T001001
Issue : 21.09.99
HANDBOOK: 485101 (rev.0.)
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
1.1
1.1
CONTENTS
Page No.
INTRODUCTION
WARRANTY
1.3
1.4
SAFETY PRECAUTIONS
1.5 - 1.9
Decals
1.9
SPECIFICATIONS
1.10
ASSEMBLY INSTRUCTIONS
General Assembly
1.11 - 1.13
1.11
Assembling the Mower for the First Time
1.12- 1.13
STARTING THE ENGINE
Before Starting the Engine
To Start the Engine
1.14 - 1.16
1.14 - 1.15
1.16
STOPPING THE ENGINE
1.17
OPERATING THE MOWER
Safety Notice
1.18 - 1.23
1.18
Height of Cut
1.18
Travel
1.19
Turning the Mower
1.19
Mowing with Grass Collection
Mowing without Grass Collection
Heavy Growth
1.20
1.21
1.21
Moving the Mower across Non-Grassed Areas
Cutterbar Operation
1.21
1.22
Mowing and Grass Care Tips
1.23 - 1.24
MAINTENANCE
Engine
1.25 - 1.33
1.25
Throttle Cable Adjustment
Carburettor Adjustments
Oil Service
1.25
1.26
1.26
Air Cleaner Service
Spark Plug Service
Keeping the Engine Clean
Grassbag
1.27
1.27
1.28
1.28
Deck Housing
1.28
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
1.2
1.2
CONTENTS
Page No.
MAINTENANCE Continued.
Securing Nuts and Bolts
Lubrication
1.29
1.29
Clutch Cable Adjustment
Cutterbar
Maintenance Schedule
- After First 5 Hours
1.29
1.30 - 1.31
1.32 - 1.33
1.32
- Every 5 Hours or Daily
- Every 25 Hours or Every Season
- Every 50 Hours or Every Season
- Every 100 Hours or Every Season
1.32
1.32
1.33
1.33
PREPARING THE MOWER FOR STORAGE
FAULT FINDING
1.34
1.35 - 1.37
2.1 - 2.3
2.4
485T PARTS LIST
485T PARTS DIAGRAM
ENGINE ANCILLARY PARTS
WARRANTY ENGINE
NOTES
2.5
2.6
2.7
CUSTOMER INFORMATION
2.8
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
1.3
1.3
INTRODUCTION
Thank you for purchasing a Hayter mower. The following pages are designed to help you
gain safe and efficient service from your machine.
IMPORTANT: This ‘Owners Handbook’ should be regarded as part of the machine as it
gives essential information regarding machine safety, operation, maintenance and
specifications. Read and understand this handbook prior to operating your machine for the
first time. Make sure you are familiar with all the controls and points of regular maintenance.
If you have any doubts, consult your Hayter authorised dealer who will be pleased to give
you assistance.
IMPORTANT: This machine is designed solely for use in a domestic grass cutting
environment. Use in any other way is considered as contrary to the intended use. Compliance
with and strict adherence to the conditions of operation, service and repair as specified in this
handbook also constitute essential elements of the intended use.
This machine should be operated, serviced and repaired only by persons who are familiar with
its particular characteristics and who are acquainted with the relevant safety procedures.
The safety precautions listed here in and all other generally recognised regulations on safety
must be observed at all times.
Any arbitrary modifications carried out to this machine may relieve Hayter Limited of
liability for any resulting damage or injury.
All Hayter mowers are robustly constructed and designed for efficient economical
performance under normal mowing conditions. Correct operation and maintenance will
ensure a long and satisfactory service life. Prior to despatch from our factory every effort is
made to ensure your machine arrives in perfect condition. Your dealer will carry out a pre-
delivery inspection to ensure that there has been no transit damage prior to installation.
Please allow your dealer to familiarise you with the controls and safety features of the
machine during installation.
Throughout this handbook all references to left hand and right hand are as viewed from
behind the handlebar, facing in the direction of
forward travel.
This handbook is based on information
available at the time of publication.
HAYTER LIMITED reserve the right to make
changes at any time without notice.
1D485
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
1.4
1.4
WARRANTY
LIMITED WARRANTY
Hayter Limited warrants to the original user/purchaser that this unit shall be free from defects
in material and workmanship under normal use and service for a period of three years from the
date of purchase. The manufacturers of the engine and battery pack system (where applicable)
furnish their own warranty and services are provided through their authorised network (Refer to
"Engine/Battery Pack Warranty Statement"). To qualify for the full benefit of the warranty, the
warranty registration card must be returned within 60 days of purchase. Subject to the conditions
and exclusions noted in this limited warranty, we shall at our option, repair or replace any
warranted part during the applicable period. If you are in doubt or experience any difficulty,
please consult a Hayter Authorised Service Dealer for clarification.
To qualify for the extended warranty (second and third year) of the three year limited warranty
the machine must have annual services carried out by an Authorised Hayter Service Dealer.
These chargeable services should be carried out within 12 and 24 months of the date of purchase.
Excluded from the extended warranty period are those items which are subject to normal wear
and tear e.g. tyres, wheels, cutterbars, cables, batteries and other consumable wearing parts.
All consumer machines which are fitted with a genuine Hayter friction disc as original
equipment before use, are covered by a Lifetime Warranty against the engine crankshaft
bending. Note: friction washers, blade brake units and other such devices are not applicable.
Only machines fitted with a genuine Hayter friction disc, which are used in accordance with the
recommended operating and maintenance procedures, are covered.
This warranty does not apply to any unit that has been tampered with, altered, misused, abused or
used for hire, and will become invalid if non genuine Hayter parts are fitted. This warranty does
not cover minor mechanical adjustments unless they are due to defective material or
workmanship. Consult the Owner's Handbook or a Hayter Authorised Service Dealer for
assistance when making these adjustments.
A warranty period of 90 days applies to machines used for commercial purposes.
To make a warranty claim, return the unit to a Hayter authorised dealer along with proof of
purchase stating the machine serial number and date of purchase. The service receipt(s) or this
Owners Handbook with the 1st/2nd year service boxes fully completed, must be produced as
proof of entitlement to the extended warranty period. Subject to the conditions and exclusions in
this limited warranty, the authorised dealer will, at our option, repair or replace any warranted
part within the duration of the warranty period.
This limited warranty gives you specific legal rights and is in addition to any statutory rights to
which you may be entitled and your statutory rights are not affected by this warranty. If you need
additional information concerning this written warranty, or assistance in obtaining services,
please write to : HAYTER LIMITED, Service Department, Spellbrook, Bishop's Stortford,
Hertfordshire CM23 4BU
UK ONLY: Details of your local Hayter authorised dealer are contained in Yellow Pages or
contact:- Freephone 0800 616298.
1st Year
Service
Record
2nd Year
Service
Record
Date....................................................................
Signed................................................................
Download from Www.Somanuals.com. All Manuals Search And Download.
Date.............................................................
Signed..........................................................
485141EB201198A
SAFETY PRECAUTIONS
1.5
1.5
SAFETY PRECAUTIONS
THIS SYMBOL MEANS BE ALERT! YOUR SAFETY IS INVOLVED.
WHEN YOU SEE THIS SYMBOL BE ALERT TO THE POSSIBILITY
OF INJURY. CAREFULLY READ THE MESSAGE THAT FOLLOWS
AND INFORM OTHERS.
EXERCISE GREAT CARE AND FOLLOW THE ADVICE GIVEN TO
AVOID POTENTIALLY HAZARDOUS SITUATIONS.
The Harrier 48 is perfectly safe if used correctly. Failure to observe the
following simple precautions may result in serious injury.
Training:
Read the instructions carefully. Ensure that you are familiar with the controls and the
proper use of the equipment. Learn how to stop the mower quickly in an emergency.
Never allow children or people unfamiliar with these instructions to use the mower.
Never mow while people, especially children, or pets are nearby.
Keep in mind that the user is responsible for accidents or hazards occurring to other people
or their property.
Preparation:
While mowing, always wear substantial footwear and long trousers. Do not operate the
equipment when barefoot or wearing sandals.
Thoroughly inspect the area where the mower is to be used and remove all objects which may
be thrown by the machine.
WARNING: Petrol is highly flammable.
- Store fuel in containers specifically designed for this purpose.
- Refuel outdoors only and do not smoke while refuelling.
- Add fuel before starting the engine. Never remove the cap from the fuel tank or add petrol
while the engine is running or when the engine is hot. Allow the engine to cool for at least 2
minutes before refuelling.
- Do not attempt to start the engine if petrol is spilled or a smell of petrol is present. Move
the mower away from the area of spillage and avoid creating any source of ignition until
petrol vapours have dissipated.
- Always use fresh fuel. Stale fuel can block the carburettor and cause leakage.
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY PRECAUTIONS
1.6
1.6
SAFETY PRECAUTIONS
Continued.
- Replace fuel tank and container caps securely.
- Replace faulty exhaust mufflers.
Always ensure that the mower is in a safe operating condition. Frequently check all nuts,
bolts and screws for tightness. Use only genuine Hayter replacement parts.
A damaged cutterbar or loose fixing screws are major hazards. Before use, visually inspect
the cutting mechanism to ensure that it is in good condition. A damaged cutterbar must be
replaced immediately with a genuine Hayter replacement part. A cutterbar which is slightly
worn can be re-sharpened. Ensure that both cutting edges are re-sharpened equally to main-
tain balance. An unbalanced cutterbar may cause serious damage to your machine.
Refer to “Maintenance”.
Operation:
Do not operate the engine in a confined space where dangerous carbon monoxide fumes can
collect.
Always pull the starter cord slowly until resistance is felt. Then pull the cord rapidly to avoid
kickback and prevent hand or arm injury.
Mow only in daylight or good artificial light.
Avoid using the mower on wet grass, where feasible.
Always be sure of your footing on slopes.
Walk, never run.
Mow across the face of slopes, never up and down.
Exercise extreme caution when changing direction on slopes.
Do not mow excessively steep slopes.
Use extreme caution when reversing or pulling the mower towards you.
Stop the engine if the mower has to be tilted for transportation when crossing surfaces other
than grass and when transporting the mower to and from the area to be mowed.
Never operate the mower unless the guards are securely in position and in good condition.
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY PRECAUTIONS
1.7
1.7
Continued.
SAFETY PRECAUTIONS
Do not change the engine governor settings or overspeed the engine.
Disengage the rear roller drive clutch before starting the engine.
Start the engine carefully, with feet well away from the cutterbar.
Do not tilt the mower when starting the engine.
Do not put hands or feet near or under rotating parts.
Never pick up or carry a mower while the engine is running.
Stop the engine and disconnect the spark plug lead:
- Before clearing blockages or unclogging the discharge chute.
- Before cleaning / checking or working on the mower.
- After striking a foreign object. Inspect the mower for damage and make repairs
before restarting and operating the mower.
- If the mower starts to vibrate abnormally (check immediately).
Stop the engine:
- Whenever you leave the mower.
- Before refuelling.
Never lift the deflector plate whilst the mower is in operation.
Never touch the engine muffler / muffler guard or cooling fins when the engine is hot.
WARNING: THE CUTTERBAR CAN CONTINUE TO ROTATE
AFTER THE ENGINE IS SWITCHED OFF
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY PRECAUTIONS
1.8
1.8
Continued.
SAFETY PRECAUTIONS
Maintenance and Storage:
Keep all nuts, bolts and screws tight to ensure that the equipment is in safe operating
condition.
Frequently check fuel lines and fittings for cracks or leaks and replace if necessary.
Never check for a spark with the spark plug removed. (Use an approved tester).
Never crank the engine with the spark plug removed. If the engine is flooded, move the
throttle to the ‘fast’ position and crank the engine until it starts.
Never strike the flywheel with a hammer or hard object as this may cause the flywheel to
shatter in operation. Always use the correct tools to service the engine.
Never operate the engine without a muffler guard. Inspect the muffler periodically and
replace if worn or leaking.
Never start the engine with the air-cleaner or air-cleaner cover removed.
Never store the mower with petrol in the tank within an enclosed area where fumes may reach
an open flame or spark.
Allow the engine to cool before storing in any enclosure.
To reduce the fire hazard, keep the engine, muffler, cooling fins and petrol storage area free
of grass, leaves, or excessive grease.
Check the grassbag frequently for wear or deterioration.
Replace worn or damaged parts for safety.
If the fuel tank has to be drained, it is essential that this be done outdoors.
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY PRECAUTIONS
1.9
1.9
DECALS
WARNING DECAL
WARNING - RISK OF DANGER - SAFETY
ALERT.
DANGER OF SEVERING TOES OR
FINGERS IN CUTTING MECHANISM.
DANGER OF BEING HIT BY THROWN
OBJECTS. KEEP BYSTANDERS AT A SAFE
DISTANCE FROM THE MACHINE.
STOP ENGINE AND REMOVE SPARK PLUG
LEAD BEFORE PERFORMING MAINTE-
NANCE OR REPAIR WORK.
CAREFULLY READ THE OWNERS HAND-
BOOK BEFORE USING THE MACHINE.
CUT HEIGHT ADJUSTMENT:
305113
THROTTLE CONTROL:
STOP
BLADE BRAKE CLUTCH DECAL:
Part No. 343019
2
1
2
1
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
1.10
1.10
SPECIFICATIONS
MODELS
Engine
CODE 485T
Blade Brake Clutch - Auto Drive
Briggs & Stratton
Diamond XTL-45
Engine Type
12G882-1512-21
2950 rpm
Engine / Cutterbar Speed
Fuel Type
Unleaded Petrol
1.5 litres
Fuel Capacity
Oil Type
SAE 30 engine oil
0.6 litres
Oil Sump Capacity
Cutting Width
Cutting Height
Overall Dimensions
Dry Weight
480mm
12 - 65mm
1040 x 514 x 1377mm
49 Kg
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTIONS
1.11
1.11
ASSEMBLY INSTRUCTIONS
SAFETY NOTICE
Before using the mower, read the owner’s handbook carefully.
Pay particular attention to the safety precautions.
MS001
GENERAL ASSEMBLY
1. Spark Plug Lead
2. Air Cleaner
3. Engine Cover
4. Fuel Cap
5. Serial Number Label
6. Oil Filler & Dipstick
11
7. Rear Deflector
12
8. Engine Start Grip
10
9. Throttle Control
10. Cutterbar Stop Lever
9
13
11. Handlebar
12. Ground Drive Clutch Lever
8
13. Blade Brake Clutch Lever
14. Grassbag Assembly
15. Handlebar Securing Knob
16. Handlebar Height Adjust Knob
7
17. Height of Cut Lever
18. Muffler Guard
6
14
15
5
4
3
2
1
16
17
18
1D485S
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTIONS
1.12
1.12
ASSEMBLING THE MOWER FOR THE FIRST TIME
DELIVERY CHECKLIST
Description
Quantity
Check that parts are delivered correctly: Remove the
mower from the packaging and check that all loose items
have been supplied correctly. Refer to the delivery check-
list opposite and the general assembly. If any items are
missing contact, your local Hayter dealer.
Grassbag
Owner’s Handbook
Warranty Registration Card
1
1
1
Assemble the handlebar: Unscrew the handlebar securing
knobs sufficiently to allow the handlebar to be pivoted.
Move the engine stop lever away from the engine to avoid
damage and unfold the handlebar to its operating position.
Ensure that both Knobs are on the outside of the handlebar
and the cable guide is positioned as shown. Tighten to
secure handlebar in position.
CS005
IMPORTANT - PREVENT DAMAGE : When unfold-
ing the handlebar, take care to ensure that the controls
and cables do not become damaged. Always replace
damaged controls and cables before using the mower.
CS072
Adjust height of handlebar: Unscrew the two larger
Knobs at base of handlebar sufficiently to allow it to be
moved to the upper, middle or lower position. Secure in
best position for comfort. Ensure that both sides are set to
the same height.
CS006
Assemble the grassbag: Remove the long ribbon label by
cutting it off close to the grassbag. Discard the ribbon label.
WARNING - AVOID ENTANGLEMENT : Completely
remove this ribbon before using the mower
CS009
Grassbag attachment: Raise the rear deflector. Lower the
grassbag through the handlebar and hook in position behind
the deflector springs. Lower the grassbag to rest against the
rear of the mower. Finally, lower the rear deflector to rest
against the top of the grassbag.
CS007
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTIONS
1.13
1.13
ASSEMBLING THE MOWER FOR THE FIRST TIME
Continued.
1
2
Check blade brake / clutch controls: Operate the blade
stop lever (A) several times, to ensure the lever moves
freely. Hold the lever against the handlebar in position (1)
and check that it returns to position (2) when released.
A
CS047
CS048
CS049
Use the right hand to hold the blade stop lever against the
handlebar (1) and use the left hand to push the blade clutch
lever (B) to the ‘engaged’ position (3). Remove the left
hand and the blade clutch lever should return to position (4),
leaving the blade drive clutch engaged.
1
4
3
B
2
Remove the right hand and check that the blade stop lever
automatically returns to position (2). There should be an
audible ‘clunk’ to indicate that the blade drive clutch has
disengaged.
1
4
A
B
STOP
Check throttle lever operation: Operate the throttle lever
several times and ensure that the cable moves freely whilst
operating the engine throttle mechanism. Slight resistance
should be felt when the lever moves to the ‘choke’ position.
CS050
Check ground drive clutch lever operation: Operate the
clutch lever several times and ensure that the cable moves
freely.
CS051
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTING THE ENGINE
1.14
1.14
BEFORE STARTING THE ENGINE
IMPORTANT - PREVENT ENGINE DAMAGE: The
engine is shipped without oil or petrol. The engine must
be filled with the correct grade of oil and petrol before
starting the engine.
CS024
Oil recommendations: Always use high quality detergent
oil classified “For service SE, SF, SG” SAE 30 oil. Never
use additives with recommended oils.
SAE 10W-30 multigrade oil may be used, but this will result
in higher engine operating temperatures with consequential
high oil consumption. It is imperative that the oil level is
checked more frequently if this grade of oil is used in order
to guard against serious engine damage.
Check oil level: Clean around the oil filler cap before
removing. With the mower on a level surface, unscrew and
remove the oil filler - dipstick. Wipe oil from it with a clean
cloth. Screw the oil filler - dipstick back in place, then
unscrew and remove it to check the oil level.
The oil level is correct when it is at the full mark on the dip-
stick. DO NOT OVERFILL.
0.15
Litres
{
Slowly fill with engine oil as necessary and replace the oil
filler - dipstick.
CS028
IMPORTANT: The oil filler dipstick must be secured to
prevent oil leakage during operation.
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTING THE ENGINE
1.15
1.15
BEFORE STARTING THE ENGINE
Continued.
Fuel Recommendations: Always use clean, fresh unleaded
petrol. Purchase fuel in quantities which can be used with-
in 30 days. Never mix oil with petrol. For added engine
protection Briggs & Stratton recommend the use of their
fuel additive which is available from an authorised Briggs &
Stratton service dealer.
Check fuel level: Clean around the fuel filler cap before
removing and fill the fuel tank with clean unleaded petrol.
Do not overfill the fuel tank. Allow 6mm minimum of tank
space for fuel expansion.
6mm
minimum
CS036
IMPORTANT: The fuel filler cap must be secured to
prevent fuel leakage during operation.
WARNING - PREVENT ACCIDENTS: The cutterbar
rotates when the engine is operating.
ALWAYS operate the engine stop lever several times and
ensure the engine stop cable moves freely before starting the
engine.
ALWAYS position the mower on a level stone free grass
surface before starting the engine. Ensure that the cutterbar
is set above grass height before the cutterbar drive is
engaged to prevent the engine being subjected to excessive
load.
CS037
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTING THE ENGINE
1.16
1.16
TO START THE ENGINE
Operate the throttle control lever: Push the lever to
‘choke’ position before starting a cold engine. It should
only be necessary to push the lever to the ‘fast’ position
before starting a warm engine.
CS052
Operate the engine start - grip: Stand behind the mower
and maintain a firm hold on the handlebar to prevent the
mower moving towards you. Use your right hand to hold
the engine start - grip and pull slowly until resistance is felt,
then pull rapidly to crank the engine. When the engine
starts carefully return the engine start - grip to the storage
position. If the engine does not start after 5 attempts - refer
to “Fault Finding”.
CS053
Allow the engine to warm up and return the throttle lever to
the ‘fast’ position after starting a cold engine.
IMPORTANT - PREVENT ENGINE DAMAGE: Never
pull the engine start - grip when the engine is running.
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
STOPPING THE ENGINE
1.17
1.17
STOPPING THE ENGINE
STOP
Stopping the engine: Push the lever to the rearmost position.
CS054
1
Emergency stop: If the engine stop lever fails, move the
throttle lever to the ‘slow’ position and disconnect the spark
plug lead to stop the engine.
2
STOP
3
CS034
1. Engine
2. Spark Plug Lead
3. Spark plug
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING THE MOWER
1.18
1.18
SAFETY NOTICE
1
WARNING - PREVENT ACCIDENTAL STARTING :
Always stop the engine and disconnect the spark plug
2
lead before cleaning, inspecting or working on the
machine.
1. Engine
2. Spark Plug Lead
3. Spark plug
STOP
3
CS034
SAFETY NOTICE
WARNING - PREVENT ACCIDENTS: Before mowing,
thoroughly inspect the area where the mower is to be
used and remove all objects which when contacted by
the mower cutterbar could become dangerous projec-
tiles.
Inspect the area for hidden obstructions which when
contacted by the cutterbar could risk health and safety.
Remember the location of these obstructions and ensure
that you mow around them.
CS031
IMPORTANT - PREVENT ENGINE DAMAGE : DO
NOT use the mower on a slope greater than 20 degrees.
CS030
o
20 max.
HEIGHT OF CUT
To adjust the height of cut: Grip the lever and pull side-
ways to disengage it from the locking notch, then push for-
wards to lower or pull backwards to raise the height of cut.
Finally release the lever at the required position and ensure
it locks firmly into one of the seven notch settings.
Always select a height of cut to suit operating conditions.
Aim to prevent engine overloading and blockages by avoid-
ing low cuts in long grass conditions. Be prepared to make
two cuts when the grass is long.
CS211
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING THE MOWER
1.19
1.19
TRAVEL
Forward travel: Hold the handlebar and operate the clutch
lever to power the mower in a forward direction.
Travel speed is controlled by engine speed. Use the throttle
control to increase forward travel speed.
CS061
Release the clutch lever to stop the mower from travelling in
a forward direction.
When the clutch lever is disengaged the mower can be oper-
ated as a push model. This feature is useful when mowing
in confined areas.
CS051
Reverse travel: Release the clutch lever. Hold and pull
against the handlebar with both hands to reverse the mower
towards you.
WARNING - PREVENT ACCIDENTS: Always reverse
the mower carefully towards you. Always disengage the
cutterbar drive before walking backwards with the
mower.
TURNING THE MOWER
To make a wide turn: Steer the mower with the handlebar
in the direction required.
To make a tight turn: Stop and apply downward pressure
on the handlebar to raise the front wheels of the mower just
above ground level and steer the mower using the handlebar
in the required direction.
WARNING - PREVENT ACCIDENTS: DO NOT raise
the front of the mower excessively when making a turn.
NEVER raise the rear of the mower when the engine is
running.
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING THE MOWER
1.20
1.20
MOWING WITH GRASS COLLECTION
The grassbag is designed to collect grass clippings.
For optimum performance, mow in dry conditions with the
throttle control set at ‘fast’.
WARNING - PREVENT ACCIDENTS: ALWAYS check
the condition of the grassbag for signs of damage and
ensure the rear deflector is positioned correctly on top of
the grassbag. Replace a damaged grassbag immediately.
DO NOT operate the mower with a damaged grassbag.
ALWAYS stop the engine and disconnect the spark plug
lead before attempting to remove a grass blockage.
Ensure the rear grass deflector is sitting on the grassbag
correctly.
CS017
Grassbag attachment: Raise the rear deflector. Lower the
grassbag through the handlebar and hook in position behind
the deflector springs. Lower the grassbag to rest against the
rear of the mower. Finally, lower the rear deflector to rest
against the top of the grassbag.
CS007
Grassbag removal: Raise the rear deflector and lift the
grassbag through the handlebar. Finally lower the rear
deflector to rest against the rear of the mower.
CS010
Grassbag emptying: To empty the grassbag, pour out the
grass clippings and shake the grassbag vigorously to clean
the airways. Good grass collection depends on good air
flow through the grassbag. When collecting grass clippings
it is important that the grassbag is emptied regularly to pre-
vent blockages and engine overloading.
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING THE MOWER
1.21
1.21
MOWING WITHOUT GRASS COLLECTION
To mow without collecting the grass clippings, remove the
grassbag and operate the mower with the rear deflector in its
lowest position.
WARNING - PREVENT ACCIDENTS: ALWAYS check
the condition of the rear deflector for signs of damage
and ensure it is positioned correctly on the rear of the
mainframe. Replace a damaged rear deflector immedi-
ately. never operate the mower with a damaged rear
deflector.
CS029
HEAVY GROWTH
Areas of heavy growth should be mown without grass col-
lection. If grass collection is required, first mow the area
without grass collection at the maximum height of cut set-
ting. Allow the grass clippings to dry out and then mow the
area at the maximum height of cut setting with the grassbag
fitted. Reduce the height of cut and mow the area again as
necessary until the required finish is obtained.
MOVING THE MOWER ACROSS NON-GRASSED AREAS
Set the mower to its maximum height of cut to protect the
cutting mechanism when moving the mower over surfaces
other than grass.
WARNING - PREVENT ACCIDENTS : ALWAYS
disengage the cutterbar drive and push the mower
carefully at slow walking speed when moving the mower
over non-grassed areas.
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING THE MOWER
1.22
1.22
CUTTERBAR OPERATION
1
General information: The cutterbar is driven by the engine
via brake/clutch device (1) which enables the
a
cutterbar to be engaged/disengaged using control levers
whilst the engine is running. The cutterbar will stop
within three seconds of releasing the blade stop lever.
CS120
WARNING - PREVENT ACCIDENTS: DO NOT operate the mower if the cutterbar
fails to stop within three seconds. Return the mower to your Hayter dealer for
examination and repair.
A friction device in the blade brake/clutch helps prevent
damage occurring to the cutting mechanism when a hidden
obstruction or overload is encountered. When the
obstruction or overload is removed, the friction device will
CS208
automatically reset.
WARNING - PREVENT ACCIDENTS: ALWAYS disengage the cutterbar drive and
stop the engine when a hidden obstruction or excessive vibration is encountered.
Disconnect the spark plug lead and examine the cutting mechanism. ALWAYS replace
a damaged cutterbar - refer to “Maintenance”.
Engaging cutterbar drive: Use the right hand to hold the
blade stop lever against the handlebar (1) and use the left
1
4
hand to push the clutch lever (2) to the ‘engaged’ position
(3). Remove the left hand and the blade clutch lever should
3
return to position (4).
CS058
2
2
Disengage cutterbar drive: Release the blade stop lever to
disengage cutterbar drive. Check that the blade stop lever
automatically returns to position (2).
CS059
Emergency stop: If the cutterbar drive mechanism fails,
stop the engine.
WARNING - PREVENT ACCIDENTS: Do not operate the mower with a faulty
cutterbar drive mechanism.
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING THE MOWER
1.23
1.23
MOWING AND GRASS CARE TIPS
In dry weather conditions leave the grass long to help retain ground moisture.
Aerate the lawn to stimulate soil organisms and root growth. In spring and late summer
remove dead grass and aerate the lawn by raking or similar means.
Keep the cutterbar sharp. A blunt cutterbar will tear the grass and cause the tips to turn
brown.
Prevent scalping. Plan your direction of travel to mow across hollows and humps.
Prevent grass damage. Take care when turning the mower.
Prevent grass damage. DO NOT mow in wet conditions.
Brush the lawn surface to disperse worm casts before mowing.
Spike compacted lawn areas with a fork. Fill the holes with sand to improve aeration and
drainage.
Mow lawns in a different direction to the previous cut.
As a general rule the grass clippings should be removed each time you mow. If weather
conditions are dry and hot and the grass is weed free, leave the clippings on the lawn to help
maintain ground moisture.
Mow lawns twice a week when the grass is growing vigorously in the summer.
Mow lawns once a week in spring, autumn and during prolonged dry weather in the summer.
Prevent grass damage - DO NOT remove more than one third of the grass height in one
cut.
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING THE MOWER
1.24
1.24
MOWING AND GRASS CARE TIPS
Continued.
Recommended grass heights for lawns :
DANGER Coarse grasses dominate fine grasses.
38mm
32mm
25mm
19mm
12mm
6mm
General lawn in spring, autumn or prolonged dry period.
General lawn in summer.
Luxury lawn in spring, autumn or prolonged dry period.
Luxury lawn in summer.
DANGER Grass strength is reduced.
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
1.25
1.25
MAINTENANCE
WARNING - PREVENT ACCIDENTS: Stop the engine
and disconnect the spark plug lead before attempting to
carry out maintenance procedures on the mower.
ENGINE
Engine Cowl
Carburettor
Spark Plug / Lead
Muffler Guard
Muffler
Oil filler Cap/ Dipstick
Start Grip
Fuel Cap
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Finger Guard
Air Cleaner
THROTTLE CABLE ADJUSTMENT
Remove two screws securing the engine cowl and remove
the cowl to expose the throttle mechanism on the front of the
engine. Loosen the outer cable clamp screw (1) and move
the governor control lever (2) to the left as far as possible.
Insert a large, flat blade screw driver (3) into the slot in the
engine control bracket (4) at the angle shown. Push the gov-
ernor control lever to the right until it just touches the screw
driver blade. Move the throttle control lever to the ‘fast’
position (not the ‘choke’ position) and re-tighten the outer
cable clamp screw. Replace the engine cowl.
3
2
1
4
CS039
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
1.26
1.26
CARBURETTOR ADJUSTMENTS
Carburettor adjustments should only be made by an authorised Briggs & Stratton dealer.
Under no circumstances should the engine be adjusted to run at a speed in excess of
3,000 r.p.m.
OIL SERVICE
Refer to the Maintenance Schedule at the end of this section and ensure that the recommen-
dations are followed. More frequent service is required when operating in adverse conditions.
- Check the oil level every 5 hours or daily and ensure that the correct oil level is main
tained. Refer to-‘Before Starting the Engine Oil Recommendations’ for oil checking
procedure and filling instructions.
- Drain the engine oil after the first 5 hours of operation and thereafter at the end of
every grass cutting season.
- Change the oil while the engine is warm. Refill with fresh clean oil of the recom-
mended SAE viscosity grade. Refer to -‘Before Starting the Engine -
: Oil Recommendations’.
WARNING - PREVENT ACCIDENTS: Drain fuel by running the engine until the fuel
tank is empty and the engine stops before attempting to tip the mower for oil draining
purposes.
1
- Remove the spark plug lead and allow the engine to cool. Tip
the mower over on to its left hand side thus ensuring that the air
cleaner is kept uppermost to prevent engine damage. Remove
2
the oil filler dipstick and drain the oil into a suitable container.
STOP
3
CS034
1. Engine
2. Spark Plug Lead
3. Spark plug
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
1.27
1.27
DUAL ELEMENT AIR CLEANER SERVICE
Refer to the Maintenance Schedule at the end of this section
and ensure that the recommendations are followed. More
frequent service is required when operating in adverse con-
ditions.
- Gain access to the pre-cleaner (4) and cartridge (3)
by loosening screw (1) and tilting cover (2).
4
5
- To service the pre-cleaner, carefully remove and
wash in a solution of liquid detergent and water.
Allow to air dry thoroughly before replacing.
- Clean the cartridge by tapping gently on a flat sur-
face. If very dirty, replace or wash in a solution of
non-foaming detergent and warm water. Rinse thor-
oughly with running water from the mesh side until
the water is clear. Allow the cartridge to stand and air
dry thoroughly before replacing. Do not use petrole-
um solvents during cleaning as this will cause the car-
tridge to deteriorate. Do not use pressurised air as this
may damage the cartridge. Do not oil the cartridge.
1. Screw
2. Tilting Cover
3. Cartridge
4. Pre-cleaner
5. Base Cover
- After servicing, install the pre-cleaner and cartridge
in the cover. Insert the tabs on the bottom of the cover
into the slots in the bottom of the base (5). Tilt the
cover upwards and securely tighten the screw to the
base.
SPARK PLUG SERVICE
Use only Briggs & Stratton spark tester (1) to check for a
spark as shown in the diagram.
Replace the spark plug every 100 hours or every season,
which ever occurs first. A spark plug wrench is available
from any authorised Briggs & Stratton service dealer.
The spark plug gap (2) should be checked with a feeler
gauge and set at 0.76mm (0.030”).
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
1.28
1.28
KEEPING THE ENGINE CLEAN
WARNING - PREVENT ACCIDENTS : Accumulation
of debris around the muffler could cause a fire. Inspect
and clean the engine after every use.
Remove all grass and debris from the engine including the
muffler / muffler guard, the air ways in the top cowl and the
surrounding deck areas on a daily basis after use.
IMPORTANT - PREVENT ENGINE DAMAGE: Never
spray the engine with water during cleaning. Water can
contaminate the fuel. Always clean with a brush or com-
pressed air.
NOTE: Grass and debris may clog the engine’s air cooling
system especially after prolonged operation while cutting
tall, dry grass. The internal cooling fins and surfaces may
require cleaning to prevent overheating and engine damage.
This may be achieved by cleaning all areas shown within the
black boundary line. We would recommend that this service
be carried out by an authorised Briggs & Stratton dealer.
GRASSBAG
Remove grass debris from the grassbag immediately after
use and check its condition for signs of damage.
WARNING - PREVENT ACCIDENTS: Replace a dam-
aged grassbag immediately.
CS017
DECK HOUSING
Remove grass debris from the top and underside of the deck
housing immediately after use.
IMPORTANT - PREVENT DAMAGE: Fertilisers and
top dressings are particularly corrosive. Thoroughly
clean the mower deck immediately after use on treated
grass and store well away from corrosive materials.
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
1.29
1.29
SECURING NUTS AND BOLTS
Regularly check that all securing nuts and bolts are tight.
Replace missing or damaged items immediately.
CS015
LUBRICATION
Lubricate the wheels, pivot points and linkages with engine
oil every 25 operating hours.
Apply a good quality medium grease to the inner control
cables at the point of entry and exit from their outer casings.
CS022
CLUTCH CABLE ADJUSTMENT
Check the clutch cable operation every 25 operating hours
and adjust if necessary. The clutch cable is adjusted cor-
rectly when the belt drive just engages with the clutch lever
positioned 32-38mm (1.1/4” - 1.1/2”) from the handlebar.
32-38mm
1.1/4"-1.1/2"
1
Unscrew the lock nuts (1) and screw the adjuster (2) in or
out as necessary. Tighten the locknuts (1) when correctly
adjusted.
2
CS060
IMPORTANT - PREVENT DAMAGE: ALWAYS oper-
ate the mower with the clutch cable correctly adjusted.
ALWAYS replace damaged cables.
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
1.30
1.30
CUTTERBAR
WARNING - PREVENT ACCIDENTS: Never work on the cutterbar unless the spark
plug lead has been removed. The cutterbar has sharp edges. ALWAYS wear strong
gloves to protect your hands when working on the cutterbar. DO NOT rotate tools
towards the cutting edges to avoid the risk of injury should the tool slip. ALWAYS use
genuine Hayter replacement parts.
The condition of the cutterbar and its mounting arrangement should be checked regu-
larly for signs of wear or damage. Ensure that the cutterbar is not bent or cracked.
A damaged cutterbar that is out of balance will vibrate excessively and may break. DO
NOT use an unbalanced cutterbar.
Regularly check that the bolt securing the cutterbar is tightened to the specified torque
of 54Nm (40 lbs ft).
Replace the cutterbar every 2 years or sooner if excessively worn or damaged.
How to remove the cutterbar: Drain the fuel by running
the engine until the fuel tank is empty and the engine stops.
Remove the spark plug lead and allow the engine to cool.
Turn the mower on its left hand side and ensure that the air
cleaner side of the engine is uppermost.
CAUTION - PREVENT INJURY: It is wise to seek
assistance when turning the mower onto its side.
Firmly grip the end of the cutterbar with the gloved hand
and remove the 2 fixing screws (1) securing the cutterbar
(2).
How to assemble the cutterbar: Assemble the cutterbar (2)
with the turned up edges facing towards the engine. Secure
the cutterbar using two new fixing screws and tighten to
1
40Nm torque.
2
CS062
WARNING - PREVENT ACCIDENTS: Never reuse the
fixing screws. Always use new cutterbar fixing screws
when refitting or replacing the cutterbar.
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
1.31
1.31
CUTTERBAR
Continued.
How to sharpen and balance the cutterbar: A slightly
worn cutterbar may be re-sharpened. Both cutting edges
must be sharpened equally to ensure balance. Sharpen the
cutterbar every 25 mowing hours or more frequently if con-
ditions require. Remove the cutterbar from the mower and
clean using a brush and water. Inspect the cutterbar for
signs of damage.
30 -45
CS040
WARNING - PREVENT ACCIDENTS : DO NOT use a
damaged or excessively worn cutterbar.
Sharpen both cutting edges with a flat file to restore the
original cutting edge.
CS025
Ensure that the cutterbar is balanced. Use a screw driver
with a round shaft to support the cutterbar through its centre
hole. Hold the cutterbar horizontal and then release. A bal-
anced cutterbar will remain horizontal. If the cutterbar is
not balanced the heavy end will rotate downwards. Sharpen
the heavy end until the cutterbar is correctly balanced.
CS026
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
1.32
1.32
MAINTENANCE SCHEDULE
Follow the hourly or calendar intervals, whichever occurs first. More frequent service
will be required if working for prolonged periods under dusty, dry conditions, or when
airborne debris is present or after extensive operation cutting tall, dry grass.
AFTER FIRST 5 HOURS
Change engine oil
EVERY 5 HOURS OR DAILY
Check oil level
Remove grass debris from around engine, muffler/muffler guard and air ways in the top
cowl.
Remove grass debris from top and underside of deck housing.
Remove grass debris from the grassbag and check for signs of damage.
Check condition of guards and safety devices.
Check condition of cutterbar.
EVERY 25 HOURS OR EVERY SEASON
Change engine oil if continuously operating under heavy load or high ambient tempera-
ture.
Service the dual element air cleaner - pre cleaner.
Lubricate wheels, pivot points and linkages.
Grease inner control cables at point of entry and exit from their outer casings.
Check clutch cable adjustment.
Sharpen cutterbar.
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
1.33
1.33
MAINTENANCE SCHEDULE Continued.
EVERY 50 HOURS OR EVERY SEASON
Change engine oil.
EVERY 100 HOURS OR EVERY SEASON
Clean engine cooling system. Clean more often under dusty conditions or when airborne
debris is present or after prolonged operation whilst cutting tall, dry grass.
Service the dual element air cleaner cartridge.
Replace spark plug.
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARING THE MOWER FOR STORAGE
1.34
1.34
PREPARING THE MOWER FOR STORAGE
Handlebar storage: To lower the handlebar unscrew the 2
small securing knobs sufficiently to allow it to be pivoted for-
wards to rest against the mower. Take care to ensure that the
control cables do not become snagged at the pivot point and
depress the engine stop lever to prevent it being damaged
through contact with the engine spark plug.
CS035
Storage for periods in excess of 30 days: Engines stored in
excess of 30 days need to be protected with Briggs & Stratton
fuel additive or drained of fuel to prevent gum from forming in
the fuel system or on essential carburettor parts. To ensure your
mower is maintained in good working order it is important that
the following procedure is adopted. Refer to the Maintenance
section as necessary.
Drain fuel from the engine by operating the engine until it stops.
Disconnect the spark plug lead.
Change the engine oil.
Remove the engine spark plug and pour 15ml of engine oil into the engine cylinder and
replace the spark plug. Do not exceed the stated volume of oil as engine damage may occur
on re-starting. Do not replace the spark plug lead. Slowly pull the engine start - grip once
to crank the engine. This will distribute the oil and help prevent engine corrosion.
Clean grass and debris from the engine cylinder, cylinder head cooling fins, under top cowl,
and around and behind muffler/muffler guard.
Clean all other areas of the mower and ensure that the grassbag is clean.
Lubricate the mower.
Treat metal parts with a water repellent anti-corrosion product.
Lower the handlebar, if desired.
Rest the mower deck on wooden blocks to remove the mower from its wheels / roller.
Cover the mower with a protective sheet and store it in a dry, ventilated area.
IMPORTANT: Fertilisers and top dressing are particularly corrosive. Thoroughly
clean the mower immediately after use on treated grass and store well away from
corrosive materials.
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
FAULT FINDING
1.35
1.35
FAULT FINDING
PROBLEM
POSSIBLE FAULT
REMEDY
Engine will not turn over
Engine stop lever released
Incorrect oil level
Operate engine stop lever
Check oil level
Engine smokes
Excess oil level
Check oil level
Air cleaner cartridge oil
soaked or plugged
Service air cleaner
Engine runs then stops
Fuel starvation
Fill fuel tank
Fuel cap vent blocked
Clean fuel cap vent
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
FAULT FINDING
1.36
1.36
Continued.
FAULT FINDING
PROBLEM
POSSIBLE FAULT
REMEDY
Engine will not start
Engine under load
Fuel starvation
Raise height of cut
Fill fuel tank
Engine cold
Set throttle to ‘choke’ position
Incorrect/contaminated fuel
Drain fuel tank and fill with
correct fuel
Spark plug lead disconnected Connect spark plug lead
Throttle setting incorrect
Engine brake not released
Faulty spark plug
Set throttle to ‘fast’ position
Operate engine brake lever
Clean and adjust gap or replace
Engine runs rough
Spark plug lead becoming
disconnected in use
Connect spark plug lead
Faulty spark plug
Clean and adjust gap or replace
Service air cleaner
Air cleaner blocked
Incorrect/contaminated fuel
Drain fuel tank and fill with
correct fuel
Engine vibrates excessively
Mounting bolts loose
Cutterbar screws loose
Cutterbar out of balance
Bent crankshaft
Tighten bolts
Tighten screws
Balance cutterbar
Consult your dealer
Cutterbar drive will not
engage / disengage
Faulty blade brake clutch
Consult your dealer
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
FAULT FINDING
1.37
1.37
Continued.
POSSIBLE FAULT
Undulating ground conditions Change direction of travel
FAULT FINDING
PROBLEM
REMEDY
Uneven cut
Cutterbar worn
Sharpen the cutterbar
Balance the cutterbar
Inspect and replace as necessary
Mow dry grass
Cutterbar out of balance
Wheels / roller damaged
Grass is wet
Discharge chute blocks
Cut height too low
Grassbag full
Increase cut height
Empty grassbag
Slow engine speed
Increase engine speed
Clean the grassbag
Airflow through the
grassbag is restricted
Mower is hard to push
Cut height too low
Increase cut height
Wheels / roller damaged
Inspect and lubricate or replace
as necessary
Mower will not self propel
Poor grass collection
Clutch out of adjustment
Drive belt damaged
Adjust clutch cable
Replace drive belt
Clean the grassbag
Airflow through the
grassbag is restricted
Discharge chute blocked
Slow engine speed
Wet grass
Remove blockage
Increase engine speed
Mow dry grass
Grassbag full
Empty grassbag
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
485T PARTS LIST
2.1
2.1
PARTS LIST
ITEM NO. DESCRIPTION
PART NO.
QTY
1
2
3
4
5
6
7
8
Mainframe - Casting
Plate - Location RH
Clamp - Boss Inner
Clamp - Boss Outer
Handwheel - Assy
Spacer - BBC
Throttle Control & OPC Cable
Engine - B/S Diamond XTL50 APTO
Decal - Engine
Knob - Handlebar
Handlebar - Lower
Bolt - Handlebar
Nut - Nylon Insert
Washer - Plain
480010V
480083V
480084W
480085W
480054
485006
485026
485110
485111
480088
480089W
226024
09544
1
1
2
2
2
1
1
1
1
2
2
2
3
1
1
3
1
1
1
1
1
2
1
1
2
1
1
1
1
1
1
1
2
2
1
1
1
1
2
1
1
3
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
09472
Guide Rope
Bush Lever
Decal - Operation
Blade Stop Lever
Plastic Ferrule
305093
226034
343019
319006W
305115
485008W
219090
343025
480123
306108
09600
480094
480109
480058W
480140
03997
Handlebar
Lever - Clutch
Plastic Nut Cap M6
Cable Guide
Bracket - Cable Clutch
Screw - Deltite Posi Pan
Cable - Clutch
Grassbag Assy (includes items 28, 36,104 & 105)
Frame - Grassbag
Deflector - Rear
Pin - Roll
Spring - Deflector RH
Rod - Deflector
Screw - Hex. Hd. Taptite
Bolt - Coach
Knob - HOC
480131
480062
09758
09549
480134
480107
480130
480082V
480055
480014
480050
09575
Base/Fabric - Grassbag Assy
Spring - Deflector LH
Plate - Location LH
Plate - Handlebar Retainer
Cover - APTO
Bearing - APTO
Screw - Washer Hd Taptite
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
485T PARTS LIST
2.2
2.2
PARTS LIST
ITEM NO. DESCRIPTION
PART NO.
QTY
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
Bush
340154
09591
2
3
1
1
1
1
4
2
2
2
3
22
2
2
2
1
1
1
1
1
1
1
4
1
1
1
2
1
1
1
1
1
1
2
1
1
1
1
1
1
Screw - Taptite
Foam Strip
Lever HOC
HOC Moulding
Throwplate - Main Body
Screw - Taptite
Bearing - Roller Housing
Roller - Rear W/A
Spring Tension - Rear Axle
Washer
480119
480128
480126
480011
09545
219102
480151W
480133
09262
Screw - Taptite
09365
Bush - Oilite Roller
Roller Freewheel - Rocket Band
Spacer - Nylon
Shroud - Freewheel
Locknut
340129
340150
340149
340168
340163
480032
480039
480159W
5321
Shaft - Roller
Sprocket - 22 Teeth
Frame - Rear Roller W/A (inc. item 114)
Key - woodruff
Circlip
Washer
1428
480097
480043
480068
480045
219037
480017W
480095
480063
02575
Cover - Transmission
Chain
Rod - Connecting
Plate - Securing
Filler - Throwplate
Pulley - Sprocket Fixedspeed
Belt - V APTO
Washer
Circlip
Pulley - Jockey
Washer - Starlock
Bracket - Idler Assy
Belt Guide
Pulley - Drive APTO
Spring - Torsion Idler
Bush
03096
219156
0201086
480115
480116
480038
480066
4452
Washer - Plain
09280
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
485T PARTS LIST
2.3
2.3
PARTS LIST
ITEM NO. DESCRIPTION
PART NO.
QTY
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
Nut M4 - Nylon Insert
M10 x 25 Tuf-Lok Screw
09657
09747
1
2
1
1
1
1
3
2
2
2
1
2
1
1
2
1
2
6
1
1
2
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
Blade Brake Clutch
Cutterbar - BBC
Cover - Throwplate Drive
Support Plate Assy
Spacer
Cap - Hub
Nut - UNF Nyloc
Wheel
Axle - Front W/A
Moulding - Front axle Bearing
Fin - Front Insert
Decal - Hayter & Royal Warrant
Nut - M8 Shouldered
Guide - Rope
485007
485005
480012
319008W
321034
219143
4486
5218
219031
219036
480013
219186
480086
305127
300160
3966
99
Plug - Tube
Tie - Cable
Setscrew
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
09704
485028
09384
Control - BBC Assy
Screw Pan Hd.
Grassbag Filler
Grassbag Top
Nipple Split
Compensating Spring
Spring
Centre Bolt BBC
Screw Soc. Shld
Screws
Clip - Cable
Torsion Spring HOC
Bracket HOC
Rivets
Ratchet
480052
480107
510118
319018
343011
343029
ZIS8L030S
09634
287034
480132
480157W
-
480156
480018
09687
Cover Plate
Screw
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
485T PARTS DIAGRAM
2.4
2.4
20
21
17
19
7
18
103
16
13
15
13
102
101
22
25
14
13
24
9
100
10
100
8
98
7
99
12
26
83
99
12
100
11
11
105
100
10
100
23
29
30
104
32
34
31
33
100
6
35
5
45
4
47
97
37
3
2
39
42
40
116
1
41
28
38
27 -Grassbag Assy.
Includes Items
28,36,104,105
36
5
3
43
39
54
96
97
4
52
70
53
52
53
54
111
48
112
53
118
49
52
89
88
44
56
63
57
58
57
55
89
54
54
49
65
56
60
52
50
44
54
51
59
44
90
91
51
62
87
69
74
73
117
106
68
108
85
86
110
107
55
50
109
54
49
79
78
26
61
64
92
65
69
93
94
76
71
82
84
72
49
81
92
68
102
94
54
67
66
75
76
80
54
77
91
42
95
46
113
114
90
54
54
115
54
1D485S01D
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGINE ANCILLARY PARTS
2.5
2.5
These parts are available through an authorised Briggs & Stratton dealer.
FUEL ADDITIVE
AIR CLEANER CARTRIDGE
Pre-cleaner
493537
SPARK PLUG
SPARK PLUG WRENCH
SPARK PLUG TESTER
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGINE WARRANTY
2.6
2.6
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
2.7
2.7
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
CUSTOMER INFORMATION
2.8
2.8
Machine Serial No: .....................................................................................
Engine Serial No: ........................................................................................
485101MT210999A
Download from Www.Somanuals.com. All Manuals Search And Download.
|