SEBU7858-03
July 2009
Operation and
Maintenance
Manual
627G Wheel Tractor-Scraper
DBD1-Up (Machine)
DBZ1-Up (Scraper)
SAFETY.CAT.COM
Download from Www.Somanuals.com. All Manuals Search And Download.
6
SEBU7858-03
Safety Section
Safety Messages
Safety Section
i03640971
Safety Messages
SMCS Code: 7000; 7405
There are several specific safety messages on this
machine. The exact location of the safety messages
and the description of the safety messages are
reviewed in this section. Please become familiarized
with all safety messages.
Make sure that all of the safety messages are legible.
Clean the safety messages or replace the safety
messages if you cannot read the words. Replace the
safety messages if the illustrations are not legible.
When you clean the safety messages, use a cloth,
water and soap. Do not use solvent, gasoline, or
other harsh chemicals to clean the safety messages.
Solvents, gasoline, or harsh chemicals could loosen
the adhesive that secures the safety message. Loose
adhesive will allow the safety message to fall.
Replace any safety message that is damaged, or
missing. If a safety message is attached to a part
that is replaced, install a safety message on the
replacement part. Any Caterpillar dealer can provide
new safety messages.
Download from Www.Somanuals.com. All Manuals Search And Download.
SEBU7858-03
7
Safety Section
Safety Messages
g01953867
Illustration 2
Download from Www.Somanuals.com. All Manuals Search And Download.
8
SEBU7858-03
Safety Section
Safety Messages
g01954945
Illustration 3
Download from Www.Somanuals.com. All Manuals Search And Download.
SEBU7858-03
9
Safety Section
Safety Messages
Do Not Operate (1)
Crushing Hazard (2)
This safety message is positioned on the right side of
the ROPS. This safety message is also positioned in
the engine compartment of the machine. This safety
message is also positioned on the scraper engine
on the left side.
This safety message is positioned on each side of
the hitch link.
g01379133
g01370904
Hitch and steering movement can reduce clear-
ances suddenly and cause personal injury...
Do not operate or work on this machine unless
you have read and understand the instructions
and warnings in the Operation and Maintenance
Manuals. Failure to follow the instructions or heed
the warnings could result in injury or death. Con-
tact your Caterpillar dealer for replacement manu-
als. Proper care is your responsibility.
Stop engine before servicing.
No Clearance (3)
This safety message is positioned on each side of
the steering link.
g01371644
Stay back a safe distance. No clearance for a per-
son in this area when the machine turns. Severe
injury or death from crushing could occur.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
SEBU7858-03
Safety Section
Safety Messages
Do Not Weld On The ROPS/FOPS
Structure (4)
Do Not Weld On The ROPS/FOPS
Structure (5)
This safety message is positioned outside of the cab
to the left of the rear window.
This safety message is positioned on the right side of
the ROPS.
g01118646
g01132602
Structural damage, an overturn, modification, al-
teration, or improper repair can impair this struc-
ture's protection capability thereby voiding this
certification. Do not weld on or drill holes in the
structure. Consult a Caterpillar dealer to deter-
mine this structure's limitations without voiding
its certification.
Structural damage, an overturn, modification, al-
teration, or improper repair can impair this struc-
ture's protection capability thereby voiding this
certification. Do not weld on or drill holes in the
structure. Consult a Caterpillar dealer to deter-
mine this structure's limitations without voiding
its certification.
This machine has been certified to the standards
that are listed on the certification film. The maximum
mass of the machine, which includes the operator
and the attachments without a payload, should not
exceed the mass on the certification film.
Refer to Operation and Maintenance Manual,
“Guards (Operator Protection)” for more information.
Refer to Operation and Maintenance Manual,
“Guards (Operator Protection)” for more information.
Download from Www.Somanuals.com. All Manuals Search And Download.
SEBU7858-03
11
Safety Section
Safety Messages
Seat Belt (6)
Improper Connections For Jump
Start Cables (8)
This safety message is positioned on the right side of
the ROPS.
This safety message is positioned inside the battery
compartment of the tractor.
g01370908
g01370909
A seat belt should be worn at all times during ma-
chine operation to prevent serious injury or death
in the event of an accident or machine overturn.
Failure to wear a seat belt during machine opera-
tion may result in serious injury or death.
Explosion Hazard! Improper jumper cable connec-
tions can cause an explosion resulting in serious
injury or death. Batteries may be located in sep-
arate compartments. Refer to the Operation and
Maintenance Manual for the correct jump starting
procedure.
High Compressed Spring (7)
This safety message is positioned on each brake
actuator.
Refer to Operation and Maintenance Manual, “Engine
Starting with Jump Start Cables” for more information.
g01379131
Highly compressed spring inside this housing can
cause serious physical injury or death.
Do not service until you read and understand the
information in the service manual when servicing
the parking/secondary brake actuator.
Download from Www.Somanuals.com. All Manuals Search And Download.
12
SEBU7858-03
Safety Section
Safety Messages
Engine Coolant (9)
Engage The Apron Locking Pin (10)
This safety message is positioned on the top of the
radiator tank.
This safety message is positioned on the right side
of the bowl.
g01371640
g01132609
The coolant is hot and the coolant is under pres-
sure. Do not touch the hot surfaces. Refer to the
Operation and Maintenance Manual for the proce-
dure to follow when you check the radiator.
Apron movement could cause serious injury or
death. Read the Operation and Maintenance Man-
ual for the proper procedure to engage the apron
pin.
Refer to Operation and Maintenance Manual,
“Cooling System Coolant Level - Check” for more
information.
Refer to Operation and Maintenance Manual,
“Blocking the Bowl and Apron” for more information.
Download from Www.Somanuals.com. All Manuals Search And Download.
SEBU7858-03
13
Safety Section
Safety Messages
Engine Coolant (11)
Engage The Apron Locking Pin (12)
This message is located to the right hand side of
the access door that is on the top of the rear engine
hood for the scraper.
This safety message is positioned on the left side
of the bowl.
g01633733
g01371640
Apron movement could cause serious injury or
death. Read the Operation and Maintenance Man-
ual for the proper procedure to engage the apron
pin.
The coolant is hot and the coolant is under pres-
sure. Do not touch the hot surfaces. Refer to the
Operation and Maintenance Manual for the proce-
dure to follow when you check the radiator.
Refer to Operation and Maintenance Manual,
“Blocking the Bowl and Apron” for more information.
Refer to Operation and Maintenance Manual,
“Cooling System Coolant Level - Check” for more
information.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
SEBU7858-03
Safety Section
Safety Messages
Product Link (13) (If Equipped)
Crushing Hazard (14)
This safety message is positioned in the cab.
This safety message is located on the right rear
ROPS post.
g01953898
There is restricted visibility to the area directly be-
hind the machine. Failure to make sure the area is
clear could result in injury or death. Use a second
person on the ground to make sure that the area
is clear before you operate the machine in the RE-
VERSE position. Refer to the Operation and Main-
tenance Manual, “Operation Information” for more
information.
g01381177
This machine is equipped with a Caterpillar
Product Link communication device. When elec-
tric/electronic detonators are used, this com-
munication device should be deactivated within
12 m (40 ft) of a blast site, or within the distance
mandated under applicable legal requirements.
Failure to do so could cause interference with
blasting operations and result in serious injury or
death.
Refer to Operation and Maintenance Manual,
“Restricted Visibility” for more information.
Refer to Operation and Maintenance Manual,
“Product Link” for more information.
Download from Www.Somanuals.com. All Manuals Search And Download.
SEBU7858-03
15
Safety Section
Additional Messages
i03200484
Additional Messages
SMCS Code: 7000; 7405
g01633794
Illustration 4
Download from Www.Somanuals.com. All Manuals Search And Download.
16
SEBU7858-03
Safety Section
Additional Messages
g01633796
g01633797
g01633799
g01633801
Illustration 5
Illustration 6
Illustration 7
Illustration 8
g01633802
Illustration 9
Alternate Exit (1)
This message is located on the ROPS support
assembly behind the operator and to the right of the
operator.
g00907967
Illustration 10
If the primary exit is blocked, use the hammer to
break the window. Exit the machine through the
window.
Air Conditioner (2)
Download from Www.Somanuals.com. All Manuals Search And Download.
SEBU7858-03
17
Safety Section
Additional Messages
This message is located on the discharge line of the
air conditioner compressor.
g00924082
Illustration 11
Air Tank (3)
g01132926
This message is located at the bottom of the left side
access door on the tractor. This message is also
located at the right rear of the scraper.
Illustration 14
Release the hood brace before attempting to lower
the engine hood.
Auger Bearing (6)
This message is located on the lower bearing of the
auger behind the access door for the auger bearing.
g01119007
Illustration 12
Data Privacy (4)
This message is located in the cab.
g00941222
Illustration 15
Some oil may be lost during shipment. Fill to the top
with 90 wt. E.P. gear oil.
Cat ELC (Extended Life Coolant) (7)
This message is located inside the engine
compartment on top of the coolant tank for the tractor.
This message is also located under the access cover
for the coolant tank of the scraper.
g01418953
Illustration 13
Hood Brace (5)
This message is located on the right side of the
engine hood.
Download from Www.Somanuals.com. All Manuals Search And Download.
18
SEBU7858-03
Safety Section
General Hazard Information
Attach a “Do Not Operate” warning tag or a similar
warning tag to the start switch or to the controls
before you service the equipment or before you
repair the equipment. These warning tags (Special
Instruction, SEHS7332) are available from your
Caterpillar dealer.
Know the width of your equipment in order to maintain
proper clearance when you operate the equipment
near fences or near boundary obstacles.
Be aware of high voltage power lines and power
cables that are buried. If the machine comes in
contact with these hazards, serious injury or death
may occur from electrocution.
g01132922
Illustration 16
Engine Coolant (8)
This message is located inside the engine
compartment on the top of the coolant tank for the
tractor. This message is also located above the sight
glass for the cooling system on the right side of the
scraper.
g00702020
Illustration 19
Wear a hard hat, protective glasses, and other
protective equipment, as required.
Do not wear loose clothing or jewelry that can snag
on controls or on other parts of the equipment.
Make sure that all protective guards and all covers
are secured in place on the equipment.
g01132923
Illustration 17
Keep the equipment free from foreign material.
Remove debris, oil, tools, and other items from the
deck, from walkways, and from steps.
i03559343
General Hazard Information
Secure all loose items such as lunch boxes, tools,
and other items that are not a part of the equipment.
SMCS Code: 7000
Know the appropriate work site hand signals and
the personnel that are authorized to give the hand
signals. Accept hand signals from one person only.
Do not smoke when you service an air conditioner.
Also, do not smoke if refrigerant gas may be present.
Inhaling the fumes that are released from a flame that
contacts air conditioner refrigerant can cause bodily
harm or death. Inhaling gas from air conditioner
refrigerant through a lighted cigarette can cause
bodily harm or death.
Never put maintenance fluids into glass containers.
Drain all liquids into a suitable container.
g00104545
Illustration 18
Download from Www.Somanuals.com. All Manuals Search And Download.
SEBU7858-03
19
Safety Section
General Hazard Information
Obey all local regulations for the disposal of liquids.
Do not remove any hydraulic components or parts
until pressure has been relieved or personal injury
may occur. Do not disassemble any hydraulic
components or parts until pressure has been relieved
or personal injury may occur. Refer to the Service
Manual for any procedures that are required to
relieve the hydraulic pressure.
Use all cleaning solutions with care. Report all
necessary repairs.
Do not allow unauthorized personnel on the
equipment.
Unless you are instructed otherwise, perform
maintenance with the equipment in the servicing
position. Refer to Operation and Maintenance Manual
for the procedure for placing the equipment in the
servicing position.
When you perform maintenance above ground level
use appropriate devices such as ladders or man lift
machines. If equipped, use the machine anchorage
points and use approved fall arrest harnesses and
lanyards.
Pressurized Air and Water
g00687600
Illustration 20
Pressurized air and/or water can cause debris
and/or hot water to be blown out. This could result in
personal injury.
Always use a board or cardboard when you check
for a leak. Leaking fluid that is under pressure can
penetrate body tissue. Fluid penetration can cause
serious injury and possible death. A pin hole leak can
cause severe injury. If fluid is injected into your skin,
you must get treatment immediately. Seek treatment
from a doctor that is familiar with this type of injury.
When pressurized air and/or pressurized water is
used for cleaning, wear protective clothing, protective
shoes, and eye protection. Eye protection includes
goggles or a protective face shield.
The maximum air pressure for cleaning purposes
must be reduced to 205 kPa (30 psi) when the
nozzle is deadheaded and the nozzle is used with
an effective chip deflector and personal protective
equipment. The maximum water pressure for
cleaning purposes must be below 275 kPa (40 psi).
Containing Fluid Spillage
Care must be taken in order to ensure that fluids
are contained during performance of inspection,
maintenance, testing, adjusting and repair of the
equipment. Prepare to collect the fluid with suitable
containers before opening any compartment or
disassembling any component that contains fluids.
Trapped Pressure
Pressure can be trapped in a hydraulic system.
Releasing trapped pressure can cause sudden
machine movement or attachment movement. Use
caution if you disconnect hydraulic lines or fittings.
High pressure oil that is released can cause a hose to
whip. High pressure oil that is released can cause oil
to spray. Fluid penetration can cause serious injury
and possible death.
Refer to Special Publication, NENG2500, “Caterpillar
Dealer Service Tool Catalog” for the following items:
Tools that are suitable for collecting fluids and
equipment that is suitable for collecting fluids
•
Tools that are suitable for containing fluids and
equipment that is suitable for containing fluids
•
Fluid Penetration
Obey all local regulations for the disposal of liquids.
Pressure can be trapped in the hydraulic circuit long
after the engine has been stopped. The pressure can
cause hydraulic fluid or items such as pipe plugs to
escape rapidly if the pressure is not relieved correctly.
Download from Www.Somanuals.com. All Manuals Search And Download.
20
SEBU7858-03
Safety Section
Crushing Prevention and Cutting Prevention
Asbestos Information
Comply with app
licable rules and regulations
•
for the work place. In the United States, use
Occupational Safety and Health Administration
(OSHA) requirements. These OSHA requirements
can be found in “29 CFR 1910.1001”.
Obey environmental regulations for the disposal
of asbestos.
•
•
Stay away from areas that might have asbestos
particles in the air.
Dispose of Waste Properly
g00702022
Illustration 21
Caterpillar equipment and replacement parts that are
shipped from Caterpillar are asbestos free. Caterpillar
recommends the use of only genuine Caterpillar
replacement parts. Use the following guidelines
when you handle any replacement parts that contain
asbestos or when you handle asbestos debris.
Use caution. Avoid inhaling dust that might be
generated when you handle components that contain
asbestos fibers. Inhaling this dust can be hazardous
to your health. The components that may contain
asbestos fibers are brake pads, brake bands, lining
material, clutch plates, and some gaskets. The
asbestos that is used in these components is usually
bound in a resin or sealed in some way. Normal
handling is not hazardous unless airborne dust that
contains asbestos is generated.
g00706404
Illustration 22
Improperly disposing of waste can threaten the
environment. Potentially harmful fluids should be
disposed of according to local regulations.
Always use leakproof containers when you drain
fluids. Do not pour waste onto the ground, down a
drain, or into any source of water.
If dust that may contain asbestos is present, there
are several guidelines that should be followed:
Never use compressed air for cleaning.
•
i01359664
Avoid brushing materials that contain asbestos.
Crushing Prevention and
Cutting Prevention
•
Avoid grinding materials that contain asbestos.
•
•
SMCS Code: 7000
Use a wet method in order to clean up asbestos
materials.
Support the equipment properly before you perform
any work or maintenance beneath that equipment.
Do not depend on the hydraulic cylinders to hold
up the equipment. Equipment can fall if a control is
moved, or if a hydraulic line breaks.
A vacuum cleaner that is equipped with a high
efficiency particulate air filter (HEPA) can also be
used.
•
Use exhaust ventilation on permanent machining
jobs.
•
•
Do not work beneath the cab of the machine unless
the cab is properly supported.
Wear an approved respirator if there is no other
way to control the dust.
Unless you are instructed otherwise, never attempt
adjustments while the machine is moving or while
the engine is running.
Download from Www.Somanuals.com. All Manuals Search And Download.
SEBU7858-03
21
Safety Section
Burn Prevention
Never jump across the starter solenoid terminals
in order to start the engine. Unexpected machine
movement could result.
Ensure that the filler cap is cool before removing the
filler cap. The filler cap must be cool enough to touch
with a bare hand. Remove the filler cap slowly in
order to relieve pressure.
Whenever there are equipment control linkages the
clearance in the linkage area will change with the
movement of the equipment or the machine. Stay
clear of areas that may have a sudden change in
clearance with machine movement or equipment
movement.
Cooling system conditioner contains alkali. Alkali can
cause personal injury. Do not allow alkali to contact
the skin, the eyes, or the mouth.
Oils
Stay clear of all rotating and moving parts.
Hot oil and hot components can cause personal
injury. Do not allow hot oil to contact the skin. Also,
do not allow hot components to contact the skin.
If it is necessary to remove guards in order to perform
maintenance, always install the guards after the
maintenance is performed.
Remove the hydraulic tank filler cap only after the
engine has been stopped. The filler cap must be
cool enough to touch with a bare hand. Follow the
standard procedure in this manual in order to remove
the hydraulic tank filler cap.
Keep objects away from moving fan blades. The fan
blade will throw objects or cut objects.
Do not use a kinked wire cable or a frayed wire cable.
Wear gloves when you handle wire cable.
Batteries
When you strike a retainer pin with force, the retainer
pin can fly out. The loose retainer pin can injure
personnel. Make sure that the area is clear of people
when you strike a retainer pin. To avoid injury to
your eyes, wear protective glasses when you strike
a retainer pin.
Electrolyte is an acid. Electrolyte can cause personal
injury. Do not allow electrolyte to contact the skin or
the eyes. Always wear protective glasses for servicing
batteries. Wash hands after touching the batteries
and connectors. Use of gloves is recommended.
Chips or other debris can fly off an object when you
strike the object. Make sure that no one can be
injured by flying debris before striking any object.
i03605020
Fire Prevention and Explosion
Prevention
i01329099
SMCS Code: 7000
Burn Prevention
SMCS Code: 7000
Do not touch any part of an operating engine.
Allow the engine to cool before any maintenance is
performed on the engine. Relieve all pressure in the
air system, in the oil system, in the lubrication system,
in the fuel system, or in the cooling system before
any lines, fittings or related items are disconnected.
Coolant
When the engine is at operating temperature, the
engine coolant is hot. The coolant is also under
pressure. The radiator and all lines to the heaters or
to the engine contain hot coolant.
g00704000
Illustration 23
General
Any contact with hot coolant or with steam can cause
severe burns. Allow cooling system components to
cool before the cooling system is drained.
All fuels, most lubricants, and some coolant mixtures
are flammable.
Check the coolant level only after the engine has
been stopped.
To minimize the risk of fire or explosion, Caterpillar
recommends the following actions.
Download from Www.Somanuals.com. All Manuals Search And Download.
22
SEBU7858-03
Safety Section
Fire Prevention and Explosion Prevention
Always perform a Walk-Around Inspection, which
may help you identify a fire hazard. Do not operate
a machine when a fire hazard exists. Contact your
Caterpillar dealer for service.
Understand the use of the primary exit and alternative
exit on the machine. Refer to Operation and
Maintenance Manual, “Alternative Exit”.
Do not operate a machine with a fluid leak. Repair
leaks and clean up fluids before resuming machine
operation. Fluids that are leaking or spilled onto hot
surfaces or onto electrical components can cause a
fire. A fire may cause personal injury or death.
Remove flammable material such as leaves, twigs,
papers, trash, etc. These items may accumulate in
the engine compartment or around other hot areas
and hot parts on the machine.
Keep the access doors to major machine
compartments closed and access doors in working
condition in order to permit the use of fire suppression
equipment, in case a fire should occur.
g00704059
Illustration 24
Use caution when you are fueling a machine. Do not
smoke while you are fueling a machine. Do not fuel
a machine near open flames or sparks. Always stop
the engine before fueling. Fill the fuel tank outdoors.
Properly clean areas of spillage.
Clean all accumulations of flammable materials such
as fuel, oil and debris from the machine.
Do not operate the machine near any flame.
Follow practices for safe fueling that are described
in the “Operation” section of the Operation and
Maintenance Manual section and follow local
regulations. Never store flammable fluids in the
operator compartment of the machine.
Keep shields in place. Exhaust shields (if equipped)
protect hot exhaust components from oil spray or fuel
spray in case of a break in a line, in a hose, or in a
seal. Exhaust shields must be installed correctly.
Do not weld or flame cut on tanks or lines that contain
flammable fluids or flammable material. Empty and
purge the lines and tanks. Then clean the lines and
tanks with a nonflammable solvent prior to welding
or flame cutting. Ensure that the components are
properly grounded in order to avoid unwanted arcs.
Battery and Battery Cables
Dust that is generated from repairing nonmetallic
hoods or fenders may be flammable and/or explosive.
Repair such components in a well ventilated area
away from open flames or sparks. Use suitable
Personal Protection Equipment (PPE).
Inspect all lines and hoses for wear or deterioration.
Replace damaged lines and hoses. The lines and
the hoses should have adequate support and secure
clamps. Tighten all connections to the recommended
torque. Damage to the protective cover or insulation
may provide fuel for fires.
Store fuels and lubricants in properly marked
containers away from unauthorized personnel. Store
oily rags and flammable materials in protective
containers. Do not smoke in areas that are used for
storing flammable materials.
g00704135
Illustration 25
Download from Www.Somanuals.com. All Manuals Search And Download.
SEBU7858-03
23
Safety Section
Fire Prevention and Explosion Prevention
Caterpillar recommends the following in order to
minimize the risk of fire or an explosion related to
the battery.
An exposed wire on the ground cable between the
battery and the disconnect switch may cause the
disconnect switch to be bypassed if the exposed area
comes into contact with a grounded surface. This
may result in an unsafe condition for servicing the
machine. Repair components or replace components
before servicing the machine.
Do not operate a machine if battery cables or related
parts show signs of wear or damage. Contact your
Caterpillar dealer for service.
Follow safe procedures for engine starting with jump
start cables. Improper jumper cable connections can
cause an explosion that may result in injury. Refer to
Operation and Maintenance Manual, “Engine Starting
with Jump Start Cables” for specific instructions.
Fire on a machine can result in personal injury
or death. Exposed battery cables that come into
contact with a grounded connection can result in
fires. Replace cables and related parts that show
signs of wear or damage. Contact your Caterpillar
dealer.
Do not charge a frozen battery. This may cause an
explosion.
Gases from a battery can explode. Keep any open
flames or sparks away from the top of a battery. Do
not smoke in battery charging areas.
Wiring
Check electrical wires daily. If any of the following
conditions exist, replace parts before you operate
the machine.
Never check the battery charge by placing a metal
object across the terminal posts. Use a voltmeter or
a hydrometer.
Fraying
•
•
•
•
•
•
Daily inspect battery cables that are in visible areas.
Identify cables, clips, straps, and other restraints for
damage. Replace these items if necessary. Look for
signs of the following, which can occur over time due
to use and environmental factors:
Signs of abrasion or wear
Cracking
Discoloration
Fraying
•
Cuts on insulation
Other damage
Abrasion
•
•
•
•
•
•
Cracking
Make sure that all clamps, guards, clips, and straps
are reinstalled correctly. This will help to prevent
vibration, rubbing against other parts, and excessive
heat during machine operation.
Discoloration
Cuts on the insulation of the cable
Fouling
Attaching electrical wiring to hoses and tubes that
contain flammable fluids or combustible fluids should
be avoided.
Corroded terminals, damaged terminals, and loose
terminals
Consult your Caterpillar dealer for repair or for
replacement parts.
Replace damaged battery cable(s) and replace
any related parts. Eliminate any fouling, which may
have caused insulation failure or related component
damage or wear. Ensure that all components are
reinstalled correctly.
Keep wiring and electrical connections free of debris.
Lines, Tubes and Hoses
An exposed wire on the battery cable may cause
a short to ground if the exposed area comes into
contact with a grounded surface. A battery cable
short produces heat from the battery current, which
may be a fire hazard.
Do not bend high pressure lines. Do not strike high
pressure lines. Do not install any lines that are bent or
damaged. Use the appropriate backup wrenches in
order to tighten all connections to the recommended
torque.
Download from Www.Somanuals.com. All Manuals Search And Download.
24
SEBU7858-03
Safety Section
Fire Extinguisher Location
Ether
Ether (if equipped) is commonly used in cold weather
applications. Ether is flammable and poisonous.
Follow the correct cold engine starting procedures.
Refer to the section in the Operation and Maintenance
Manual with the label “Engine Starting”.
Do not spray ether into an engine if the machine is
equipped with a thermal starting aid for cold weather
starting.
Use ether in well ventilated areas. Do not smoke
while you are replacing an ether cylinder or while you
are using an ether spray.
g00687600
Illustration 26
Check lines, tubes and hoses carefully. Wear
Personal Protection Equipment (PPE) in order to
check for leaks. Always use a board or cardboard
when you check for a leak. Leaking fluid that is under
pressure can penetrate body tissue. Fluid penetration
can cause serious injury and possible death. A pin
hole leak can cause severe injury. If fluid is injected
into your skin, you must get treatment immediately.
Seek treatment from a doctor that is familiar with this
type of injury.
Do not store ether cylinders in living areas or in the
operator compartment of a machine. Do not store
ether cylinders in direct sunlight or in temperatures
above 49° C (120.2° F). Keep ether cylinders away
from open flames or sparks.
Dispose of used ether cylinders properly. Do not
puncture an ether cylinder. Keep ether cylinders
away from unauthorized personnel.
Fire Extinguisher
Replace the affected parts if any of the following
conditions are present:
As an additional safety measure, keep a fire
extinguisher on the machine.
End fittings are damaged or leaking.
•
Be familiar with the operation of the fire extinguisher.
Inspect the fire extinguisher and service the fire
extinguisher regularly. Follow the recommendations
on the instruction plate.
Outer coverings are chafed or cut.
•
Wires are exposed.
•
Outer coverings are swelling or ballooning.
•
Consider installation of an aftermarket Fire
Suppression System, if the application and working
conditions warrant the installation.
Flexible parts of the hoses are kinked.
•
Outer covers have exposed embedded armoring.
•
i02370502
End fittings are displaced.
•
Fire Extinguisher Location
Make sure that all clamps, guards, and heat shields
are installed correctly. During machine operation, this
will help to prevent vibration, rubbing against other
parts, excessive heat, and failure of lines, tubes and
hoses.
SMCS Code: 7000
Make sure that a fire extinguisher is available. Be
familiar with the operation of the fire extinguisher.
Inspect the fire extinguisher and service the fire
extinguisher regularly. Obey the recommendations
on the instruction plate.
Do not operate a machine when a fire hazard
exists. Repair any lines that are corroded, loose
or damaged. Leaks may provide fuel for fires.
Consult your Caterpillar dealer for repair or for
replacement parts. Use genuine Caterpillar parts or
the equivalent, for capabilities of both the pressure
limit and temperature limit.
The fire extinguisher may be mounted to the grab
handle that is located on the right platform near the
front of the engine hood. Do not block access to the
following items:
handrails
•
ladders
•
Download from Www.Somanuals.com. All Manuals Search And Download.
SEBU7858-03
25
Safety Section
Tire Information
walkways
To avoid overinflation, proper nitrogen inflation
•
•
equipment and training in the usage of the equipment
are necessary. A tire blowout or a rim failure can
result from improper equipment or from misused
equipment.
front side door of engine hood
Do not weld a bracket on the Rollover Protective
Structure (ROPS) in order to install the fire
extinguisher. Also, do not drill holes in the ROPS in
order to mount the fire extinguisher on the ROPS.
When you inflate a tire, stand behind the tread and
use a self-attaching chuck.
Servicing tires and rims can be dangerous. Only
trained personnel that use proper tools and proper
procedures should perform this maintenance. If
correct procedures are not used for servicing tires
and rims, the assemblies could burst with explosive
force. This explosive force can cause serious
personal injury or death. Carefully obey the specific
instructions from your tire dealer.
i01557411
Tire Information
SMCS Code: 7000
Explosions of air inflated tires have resulted from
heat-induced gas combustion inside the tires.
Explosions can be caused by heat that is generated
by welding, by heating rim components, by external
fire, or by excessive use of brakes.
i01122596
Electrical Storm Injury
Prevention
A tire explosion is much more violent than a
blowout. The explosion can propel the tire, the rim
components, and the axle components as far as
500 m (1500 ft) or more from the machine. Both the
force of the explosion and the flying debris can cause
property damage, personal injury, or death.
SMCS Code: 7000
When lightning is striking in the vicinity of the
machine, the operator should never attempt the
following procedures:
Mount the machine.
•
Dismount the machine.
•
If you are in the operator's station during an electrical
storm, stay in the operator's station. If you are on the
ground during an electrical storm, stay away from
the vicinity of the machine.
i03140043
Before Starting Engine
g00337832
Illustration 27
SMCS Code: 1000; 7000
(A) At least 15 m (50 ft)
(B) At least 500 m (1500 ft)
Start the engine only from the operator's
compartment. Never short across the starter
terminals or across the batteries. Shorting could
bypass the engine neutral start system. Shorting
could also damage the electrical system.
Do not approach a warm tire. Maintain a minimum
distance, as shown. Stay outside the shaded area in
Illustration 27.
Do not use water or calcium as a ballast for the tires.
Dry nitrogen gas is recommended for inflation of tires.
If the tires were originally inflated with air, nitrogen
is still preferred for adjusting the pressure. Nitrogen
mixes properly with air.
Nitrogen inflated tires reduce the potential of
a tire explosion because nitrogen does not aid
combustion. Nitrogen helps to prevent oxidation of
the rubber, deterioration of rubber, and corrosion of
rim components.
Download from Www.Somanuals.com. All Manuals Search And Download.
26
SEBU7858-03
Safety Section
Engine Starting
i03565626
Engine Starting
SMCS Code: 1000; 7000
If a warning tag is attached to the engine start switch
or to the machine controls, do not start the engine.
Also, do not move any machine controls.
Move all hydraulic controls to the HOLD position or to
the OFF position before you start the engine.
Move the transmission control (lever) to the
NEUTRAL position.
g00927804
Illustration 28
Engage the parking brake control.
Depress the machine horn (1) in order to make sure
that the machine horn works properly.
Diesel engine exhaust contains products of
combustion which can be harmful to your health.
Always start the engine in a well ventilated area.
Always operate the engine in a well ventilated area.
If you are in an enclosed area, vent the exhaust to
the outside.
Briefly sound the horn before you start the engine.
i01349075
Before Operation
SMCS Code: 7000
Clear all personnel from the machine and from the
area.
g01120628
Illustration 29
Typical example
Clear all obstacles from the path of the machine.
Beware of hazards such as wires, ditches, etc.
Adjust the mirrors (2) on your machine for the best
operator vision. Adjust both the inside mirror and the
outside mirror before you operate the machine.
Make sure that all windows are clean. Secure the
doors in the open position or in the shut position.
Secure the windows in the open position or in the
shut position.
Inspect the condition of the seat belt and the condition
of mounting hardware. Replace any damaged parts
and any worn parts. Regardless of appearance,
replace the seat belt after three years of use. Do not
use a seat belt extension on a retractable seat belt.
For the best vision of the area that is close to the
machine, adjust the rear view mirrors (if equipped).
Adjust the seat in order to achieve full pedal travel
when the operator's back is against the back of the
seat.
Make sure that the machine horn, the backup alarm
(if equipped) and all other warning devices are
working properly.
Make sure that the machine is equipped with a
lighting system that is adequate for the job conditions.
Make sure that all lights are working properly.
Fasten the seat belt securely.
Before you start the engine or before you move the
machine, make sure that no one is on the machine,
underneath the machine, or around the machine.
Make sure that there are no personnel in the area.
Download from Www.Somanuals.com. All Manuals Search And Download.
SEBU7858-03
27
Safety Section
Visibility Information
i03162317
i03641204
Visibility Information
Restricted Visibility
SMCS Code: 7000
SMCS Code: 7000
Before you start the machine, perform a walk-around
inspection in order to ensure that there are no
hazards around the machine.
The size and the configuration of this machine may
result in areas that can not be seen when the operator
is seated. Illustration 30 provides an approximate
visual indication of areas of significant restricted
visibility. Illustration 30 indicates restricted visibility
areas at ground level inside a radius of 12.00 m
(40 ft) from the operator on a machine without the
use of optional visual aids. This illustration does not
provide areas of restricted visibility for distances
outside a radius of 12.00 m (40 ft).
While the machine is in operation, constantly survey
the area around the machine in order to identify
potential hazards as hazards become visible around
the machine.
Your machine may be equipped with visual aids.
Some examples of visual aids are Closed Circuit
Television (CCTV) and mirrors. Before operating the
machine, ensure that the visual aids are in proper
working condition and that the visual aids are clean.
Adjust the visual aids using the procedures that are
located in this Operation and Maintenance Manual.
If equipped, the Work Area Vision System shall be
adjusted according to Operation and Maintenance
Manual, SEBU8157, “Work Area Vision System”.
This machine may be equipped with optional visual
aids that may provide visibility to some of the
restricted visibility areas. Refer to this Operation and
Maintenance Manual, “Mirror” for more information on
additional visibility. If your machine is equipped with
cameras, refer to this Operation and Maintenance
Manual, “Camera” for more information on additional
visibility. For areas that are not covered by the
optional visual aids, the job site organization must
be utilized to minimize hazards of this restricted
visibility. For more information regarding job site
organization refer to Operation and Maintenance
Manual, “Visibility Information”.
It may not be possible to provide direct visibility on
large machines to all areas around the machine.
Appropriate job site organization is required in order
to minimize hazards that are caused by restricted
visibility. Job site organization is a collection of rules
and procedures that coordinates machines and
people that work together in the same area. Examples
of job site organization include the following:
Safety instructions
•
Controlled patterns of machine movement and
vehicle movement
•
Workers that direct traffic to move when it is safe
•
Restricted areas
Operator training
•
•
•
Warning symbols or warning signs on machines
or on vehicles
A system of communication
•
•
Communication between workers and operators
prior to approaching the machine
Modifications of the machine configuration by the
user that result in a restriction of visibility shall be
evaluated.
g01635673
Illustration 30
Top view of the machine
Download from Www.Somanuals.com. All Manuals Search And Download.
28
SEBU7858-03
Safety Section
Operation
Note: The shaded areas indicate the approximate
location of areas with significant restricted visibility.
Do not operate the machine on ground conditions
that could result in the seat suspension travel stops
being contacted and do not operate the machine at
travel speeds that could result in the seat suspension
travel stops being contacted. Operating this machine
in very rough ground conditions or at travels speeds
not suitable for the ground conditions may result
in excessive seat vertical travel with impact of the
suspension against the travel stops, which may
cause injury. In order to minimize impact loading on
the operator, properly adjust the seat controls for the
operator weight and height. Refer to Operation and
Maintenance Manual, “Seat” for more information.
There is restricted visibility to the area directly be-
hind the machine. Failure to make sure the area is
clear could result in injury or death. Use a second
person on the ground to make sure that the area
is clear before you operate the machine in the RE-
VERSE position. Refer to the Operation and Main-
tenance Manual, “Operation Information” for more
information.
Carry attachments approximately 40 cm (15 inches)
above ground level. Do not go close to the edge of a
cliff, an excavation, or an overhang.
i03565616
Operation
If the machine begins to sideslip downward on a
grade, immediately remove the load and turn the
machine downhill.
SMCS Code: 7000
Machine Operating Temperature
Range
Avoid any conditions that can lead to tipping the
machine. The machine can tip when you work on
hills, on banks and on slopes. Also, the machine
can tip when you cross ditches, ridges or other
unexpected obstructions.
The standard machine configuration is intended
for use within an ambient temperature range
of −40 °C (−40 °F) to 50 °C (122 °F). Special
configurations for different ambient temperatures
may be available. Consult your Caterpillar dealer for
additional information on special configurations of
your machine.
Avoid operating the machine across the slope. When
possible, operate the machine up the slopes and
down the slopes.
Maintain control of the machine. Do not overload the
machine beyond the machine capacity.
Machine Operation
Never straddle a wire cable. Never allow other
personnel to straddle a wire cable.
Only operate the machine while you are in a seat.
The seat belt must be fastened while you operate the
machine. Only operate the controls while the engine
is running.
Before you maneuver the machine, make sure
that no personnel are between the machine and
attachments.
While you operate the machine slowly in an open
area, check for proper operation of all controls and all
protective devices.
Know the maximum dimensions of your machine.
Always keep the Rollover Protective Structure
(ROPS) installed during machine operation.
Before you move the machine, you must make sure
that no one will be endangered.
i02624835
Do not allow riders on the machine unless the
machine has the following equipment:
Engine Stopping
additional seat
•
SMCS Code: 1000; 7000
additional seat belt
•
Do not stop the engine immediately after the
machine has been operated under load. This can
cause overheating and accelerated wear of engine
components.
Rollover Protective Structure (ROPS)
•
Never use the work tool for a work platform.
Note any needed repairs during machine operation.
Report any needed repairs.
Download from Www.Somanuals.com. All Manuals Search And Download.
SEBU7858-03
29
Safety Section
Parking
After the machine is parked and the parking brake
is engaged, allow the engine to run for two minutes
before shutdown. This allows hot areas of the engine
to cool gradually.
A well trained operator that follows the instructions
in the Operation and Maintenance Manual has
the greatest impact on stability. Operator training
provides a person with the following abilities:
observation of working and environmental conditions,
feel for the machine, identification of potential
hazards, and operating the machine safely by making
appropriate decisions.
i03370980
Parking
When you work on side hills and when you work on
slopes, consider the following important points:
SMCS Code: 7000
Park the machine on a level surface. If you must park
on a grade, chock the machine's wheels with suitable
chocks. Take into account the following:
Speed of travel – At higher speeds, forces of inertia
tend to make the machine less stable.
Roughness of terrain or surface – The machine
may be less stable with uneven terrain.
tire size
•
machine weight
•
Direction of travel – Avoid operating the machine
across the slope. When possible, operate the
machine up the slopes and operate the machine
down the slopes. Place the heaviest end of the
machine uphill when you are working on an incline.
ground conditions
•
Apply the service brake in order to stop the
machine. Move the transmission control (lever) to
the NEUTRAL position. Move the throttle control to
the LOW IDLE position.
Mounted equipment – Balance of the machine
may be impeded by the following components:
equipment that is mounted on the machine, machine
configuration, weights, and counterweights.
Engage the parking brake.
Lower all equipment to the ground. Activate any
control locks.
Nature of surface – Ground that has been newly
filled with earth may collapse from the weight of the
machine.
Stop the engine.
Surface material – Rocks and moisture of the
surface material may drastically affect the machine's
traction and machine's stability. Rocky surfaces may
promote side slipping of the machine.
Turn the engine start switch to the OFF position and
remove the engine start switch key.
Turn the battery disconnect switch to the OFF
position. Remove the disconnect switch key if you
do not operate the machine for an extended period
of time. This will prevent drainage of the battery. A
battery short circuit, any current draw from certain
components, and vandalism can cause drainage of
the battery.
Slippage due to excessive loads – This may cause
downhill tracks or downhill tires to dig into the ground,
which will increase the angle of the machine.
Width of tracks or tires – Narrower tracks or
narrower tires further increase the digging into the
ground which causes the machine to be less stable.
i02780235
Implements attached to the drawbar – This may
decrease the weight on the uphill tracks. This may
also decrease the weight on the uphill tires. The
decreased weight will cause the machine to be less
stable.
Slope Operation
SMCS Code: 7000
Machines that are operating safely in various
applications depend on these criteria: the machine
model, configuration, machine maintenance,
operating speed of the machine, conditions of the
terrain, fluid levels, and tire inflation pressures. The
most important criteria are the skill and judgment of
the operator.
Height of the working load of the machine –
When the working loads are in higher positions, the
stability of the machine is reduced.
Operated equipment – Be aware of performance
features of the equipment in operation and the effects
on machine stability.
Download from Www.Somanuals.com. All Manuals Search And Download.
30
SEBU7858-03
Safety Section
Equipment Lowering with Engine Stopped
Operating techniques – Keep all attachments or
pulled loads low to the ground for optimum stability.
Hearing protection may be needed when the
machine is operated with an open operator station for
extended periods or in a noisy environment. Hearing
protection may be needed when the machine is
operated with a cab that is not properly maintained or
when the doors and windows are open for extended
periods or in a noisy environment.
Machine systems have limitations on slopes –
Slopes can affect the proper function and operation
of the various machine systems. These machine
systems are needed for machine control on slopes.
Note: Safe operation on steep slopes may require
special machine maintenance. Excellent skill of
the operator and proper equipment for specific
applications are also required. Consult the Operation
and Maintenance Manual sections for the proper fluid
level requirements and intended machine use.
The average exterior sound pressure level is 86
dB(A) when the “SAE J88Feb06 - Constant Speed
Moving Test” procedure is used to measure the value
for the standard machine. The measurement was
conducted under the following conditions: distance of
15 m (49.2 ft) and “the machine moving forward in an
intermediate gear ratio”.
i01329161
Equipment Lowering with
Engine Stopped
The exterior sound power level is 115 dB(A) when the
value is measured according to the static pressure
test procedures and the conditions that are specified
in “ISO 6393:2008”.
SMCS Code: 7000
Sound Level Information for
Machines in European Union
Countries and in Countries that
Adopt the “European Union
Directives”
Before lowering any equipment with the engine
stopped, clear the area around the equipment of
all personnel. The procedure to use will vary with
the type of equipment to be lowered. Keep in mind
most systems use a high pressure fluid or air to
raise or lower equipment. The procedure will cause
high pressure air, hydraulic, or some other media
to be released in order to lower the equipment.
Wear appropriate personal protective equipment and
follow the established procedure in the Operation
and Maintenance Manual, “Equipment Lowering with
Engine Stopped” in the Operation Section of the
manual.
The static operator sound pressure level is 79 dB(A)
when “ISO 6394:2008” is used to measure the value
for an enclosed cab. The test was conducted with the
cab doors and the cab windows closed. The cab was
properly installed and maintained.
“The European Union Physical
Agents (Vibration) Directive
2002/44/EC”
i03596373
Sound Information and
Vibration Information
Vibration Data for Wheel Scrapers
SMCS Code: 7000
Information Concerning Hand/Arm Vibration
Level
S/N: DBD1-Up
When the machine is operated according to the
intended use, the hand/arm vibration of this machine
is below 2.5 meter per second squared.
Sound Level Information
The operator Equivalent Sound Pressure Level
(Leq) is 81 dB(A) when “ANSI/SAE J1166 OCT 98”
is used to measure the value for an enclosed cab.
This is a work cycle sound exposure level. The cab
was properly installed and maintained. The test was
conducted with the cab doors and the cab windows
closed.
Information Concerning Whole Body Vibration
Level
This section provides vibration data and a method for
estimating the vibration level for wheel scrapers.
Note: Vibration levels are influenced by many
different parameters. Many items are listed below.
Operator training, behavior, mode, and stress
•
Download from Www.Somanuals.com. All Manuals Search And Download.
SEBU7858-03
31
Safety Section
Sound Information and Vibration Information
Job site organization, preparation, environment,
weather, and material
•
•
Machine type, quality of the seat, quality of the
suspension system, attachments, and condition of
the equipment
It is not possible to get precise vibration levels for
this machine. The expected vibration levels can be
estimated with the information in Table 1 in order
to calculate the daily vibration exposure. A simple
evaluation of the machine application can be used.
Estimate the vibration levels for the three vibration
directions. For typical operating conditions, use the
average vibration levels as the estimated level. With
an experienced operator and smooth terrain, subtract
the Scenario Factors from the average vibration level
in order to obtain the estimated vibration level. For
aggressive operations and severe terrain, add the
Scenario Factors to the average vibration level in
order to obtain the estimated vibration level.
Note: All vibration levels are in meter per second
squared.
Table 1
“ISO Reference Table A - Equivalent vibration levels of whole body vibration emission for earthmoving equipment.”
Vibration Levels
Scenario Factors
Typical Operating
Activity
Machine Family
Machine Type
X
Y
Z
X
Y
Z
axis
axis
axis
axis
axis
axis
Scraper
Wheel Scraper
work cycle
1,05
1,18
1,12
0,34
0,40
0,42
Note: Refer to “ISO/TR 25398 Mechanical Vibration -
Guideline for the assessment of exposure to whole
body vibration of ride on operated earthmoving
machines” for more information about vibration.
This publication uses data that is measured
by international institutes, organizations and
manufacturers. This document provides information
about the whole body exposure of operators of
earthmoving equipment. Refer to Operation and
Maintenance Manual, SEBU8257, “The European
Union Physical Agents (Vibration) Directive
2002/44/EC” for more information about machine
vibration levels.
Guidelines for Reducing Vibration Levels on
Earthmoving Equipment
Properly adjust machines. Properly maintain
machines. Operate machines smoothly. Maintain the
conditions of the terrain. The following guidelines can
help reduce the whole body vibration level:
1. Use the right type and size of machine, equipment,
and attachments.
2. Maintain machines according to the manufacturer's
recommendations.
The Caterpillar suspension seat meets the criteria of
“ISO 7096”. This represents vertical vibration level
under severe operating conditions. This seat is tested
with the input “spectral class EM2”. The seat has a
transmissibility factor of “SEAT<1.0”.
a. Tire pressures
b. Brake and steering systems
c. Controls, hydraulic system and linkages
3. Keep the terrain in good condition.
a. Remove any large rocks or obstacles.
b. Fill any ditches and holes.
The whole body vibration level of the machine varies.
There is a range of values. The low value is 0.5
meter per second squared. The machine meets the
short term level for the design of the seat in “ISO
7096”. The value is 1.34 meter per second squared
for this machine.
Download from Www.Somanuals.com. All Manuals Search And Download.
32
SEBU7858-03
Safety Section
Sound Information and Vibration Information
c. Provide machines and schedule time in order
e. Minimize repeated handling of loads and lifting
to maintain the conditions of the terrain.
of loads.
4. Use a seat that meets “ISO 7096”. Keep the seat
f. Minimize any shocks and impacts during sports
maintained and adjusted.
and leisure activities.
a. Adjust the seat and suspension for the weight
Sources
and the size of the operator.
The vibration information and the calculation
procedure is based on “ISO/TR 25398 Mechanical
Vibration - Guideline for the assessment of exposure
to whole body vibration of ride on operated
earthmoving machines”. Harmonized data is
measured by international institutes, organizations
and manufacturers.
b. Inspect and maintain the seat suspension and
adjustment mechanisms.
5. Perform the following operations smoothly.
a. Steer
b. Brake
This literature provides information about assessing
the whole body vibration exposure of operators of
earthmoving equipment. The method is based on
measured vibration emission under real working
conditions for all machines.
c. Accelerate.
d. Shift the gears.
6. Move the attachments smoothly.
You should check the original directive. This
document summarizes part of the content of the
applicable law. This document is not meant to
substitute the original sources. Other parts of these
documents are based on information from the United
Kingdom Health and Safety Executive.
7. Adjust the machine speed and the route in order
to minimize the vibration level.
a. Drive around obstacles and rough terrain.
b. Slow down when it is necessary to go over
Refer to Operation and Maintenance Manual,
SEBU8257, “The European Union Physical
Agents (Vibration) Directive 2002/44/EC” for more
information about vibration.
rough terrain.
8. Minimize vibrations for a long work cycle or a long
travel distance.
Consult your local Caterpillar dealer for more
information about machine features that minimize
vibration levels. Consult your local Caterpillar dealer
about safe machine operation.
a. Use machines that are equipped with
suspension systems.
b. Use the ride control system on wheel scrapers.
Use the following web site in order to find your local
dealer:
c. If no ride control system is available, reduce
speed in order to prevent bounce.
Caterpillar, Inc.
d. Haul the machines between workplaces.
9. Less operator comfort may be caused by other risk
factors. The following guidelines can be effective
in order to provide better operator comfort:
a. Adjust the seat and adjust the controls in order
to achieve good posture.
b. Adjust the mirrors in order to minimize twisted
posture.
c. Provide breaks in order to reduce long periods
of sitting.
d. Avoid jumping from the cab.
Download from Www.Somanuals.com. All Manuals Search And Download.
SEBU7858-03
33
Safety Section
Operator Station
i03634321
Rollover Protective Structure
(ROPS), Falling Object Protective
Structure (FOPS) or Tip Over
Protection Structure (TOPS)
Operator Station
SMCS Code: 7000
S/N: DBD1-Up
The ROPS/FOPS Structure (if equipped) on your
machine is specifically designed, tested and certified
for that machine. Excavators are not equipped
with ROPS structures. Any alteration or any
modification to the ROPS/FOPS Structure could
weaken the structure. This places the operator
into an unprotected environment. Modifications or
attachments that cause the machine to exceed the
weight that is stamped on the certification plate also
place the operator into an unprotected environment.
Excessive weight may inhibit the brake performance,
the steering performance and the ROPS. The
protection that is offered by the ROPS/FOPS
Structure will be impaired if the ROPS/FOPS
Structure has structural damage. Damage to the
structure can be caused by an overturn, a falling
object, a collision, etc.
Any modifications to the inside of the operator station
should not project into the operator space or into
the space for the companion seat (if equipped).
The addition of a radio, fire extinguisher, and other
equipment must be installed so that the defined
operator space and the space for the companion seat
(if equipped) is maintained. Any item that is brought
into the cab should not project into the defined
operator space or the space for the companion seat
(if equipped). A lunch box or other loose items must
be secured. Objects must not pose an impact hazard
in rough terrain or in the event of a rollover.
i01992325
Guards
(Operator Protection)
Do not mount items (fire extinguishers, first aid
kits, work lights, etc) by welding brackets to the
ROPS/FOPS Structure or by drilling holes in the
ROPS/FOPS Structure. Welding brackets or drilling
holes in the ROPS/FOPS Structures can weaken
the structures. Consult your Caterpillar dealer for
mounting guidelines.
SMCS Code: 7000
There are different types of guards that are used to
protect the operator. The machine and the machine
application determines the type of guard that should
be used.
The Tip Over Protection Structure (TOPS) is
another type of guard that is used on mini hydraulic
excavators. This structure protects the operator in
the event of a tipover. The same guidelines for the
inspection, the maintenance and the modification of
the ROPS/FOPS Structure are required for the Tip
Over Protection Structure.
A daily inspection of the guards is required in order to
check for structures that are bent, cracked or loose.
Never operate a machine with a damaged structure.
The operator becomes exposed to a hazardous
situation if the machine is used improperly or if poor
operating techniques are used. This situation can
occur even though a machine is equipped with an
appropriate protective guard. Follow the established
operating procedures that are recommended for your
machine.
Other Guards (If Equipped)
Protection from flying objects and/or falling objects is
required for special applications. Logging applications
and demolition applications are two examples that
require special protection.
A front guard needs to be installed when a work
tool that creates flying objects is used. Mesh
front guards that are approved by Caterpillar or
polycarbonate front guards that are approved by
Caterpillar are available for machines with a cab or
an open canopy. On machines that are equipped with
cabs, the windshield should also be closed. Safety
glasses are recommended when flying hazards exist
for machines with cabs and machines with open
canopies.
If the work material extends above the cab, top
guards and front guards should be used. Typical
examples of this type of application are listed below:
Download from Www.Somanuals.com. All Manuals Search And Download.
34
SEBU7858-03
Safety Section
Guards
Demolition applications
Rock quarries
•
•
•
Forestry products
Additional guards may be required for specific
applications or work tools. The Operation and
Maintenance Manual for your machine or your
work tool will provide specific requirements for the
guards. Consult your Caterpillar dealer for additional
information.
Download from Www.Somanuals.com. All Manuals Search And Download.
|