Briggs Stratton Lawn Mower 1695195 User Manual

Sub-Frame Hitch  
Installation  
Mfg. No. 1695195  
For Prestige / 1800 / 2800, Conquest / 1700 / 2700, &  
Broadmoor / 1600 / 2600 Series Tractors  
Instructions  
This kit is required when installing front mounted  
snowthrowers.  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
Sub-Frame Hitch  
Installation Instructions  
Ref Part No. Qty. Description  
1
2
3
4
5
6
7
8
9
1723292A  
1653768A  
1931335  
1919381  
1917356  
1917372  
105249  
1
1
4
4
3
4
1
1
4
1
2
1
2
1
2
1
1
1
1
1
1
2
1
1
8
1
7
6
1
1
1
2
4
1
1
1
1
1
1
1
1
1
1
2
1
1
2
4
4
1
1
SHAFT & HOOK ASSY  
CLAMP, Support  
CARRIAGE BOLT, 5/16-18 x 1  
WASHER, 11/32  
LOCKWASHER, 5/16  
NUT, 5/16-18  
PIN, Round Head, 3/8 x 2-3/8  
LIFT LEVER ASSY.  
SAFETY CLIP  
LIFT ROD  
SET COLLAR  
SPRING, Compression  
SET SCREW, 5/16-18 x 1/2  
ROD GUIDE  
ROD, Latch  
ROD, Hitch  
HITCH ASSY.  
PIN, Headless, 1/2 x 2  
BAR, Lift Link  
HAIR PIN CLIP  
PLATE, Lock, Hydraulic Lift  
SPACER  
SCREW, Whiz, 3/8-16 x 2-3/4  
CAPSCREW, 3/8-16 x 3/4  
WASHER PLAIN, 3/8  
BELT GUIDE  
LOCKWASHER, 3/8  
NUT HEX FULL, 3/8-16  
PULLEY-FLAT  
1724025  
2176012  
10 1722946  
11 8031007  
12 171011  
13 1928721  
14 1723115  
15 1733812  
16 1733309  
17 1733779A  
18 1722819  
19 1723795  
20 1960033  
21 1722469  
22 1667812  
23 1960244  
24 1921971  
25 1924940  
26 162115  
27 1916965  
28 1916950  
29 171247  
30 1666287  
31 1666294  
32 1923701  
33 158227  
34 1920415  
35 1722963  
36 1930651  
37 1704743  
38 1668282  
39 1722972  
40 1960268  
41 1704741  
42 1703371  
42 1703372  
43 1701600  
44 1922130  
45 1733814A  
46 1960074  
47 1921210  
48 1928352  
49 1724387  
50 1677135A  
PULLEY ASS'Y  
SPACER-BRG  
CAPSCREW, 3/8-16 x 2  
SPACER  
CAPSCREW, 3/8-16 x 1-1/4  
PIVOT BRACKET  
NUT LOCK, 3/8-16  
TRUNNION  
SPRING  
GUIDE ASS'Y -SPRING  
CARRIAGE BOLT, 3/8-16 x 1-1/4  
ROD ASS'Y  
V-BELT, Single-Stage Blower  
V-BELT, Two-Stage Blower  
REFLECTOR  
CAPSCREW, 3/8-16 x 2-1/4  
PUSH BAR LATCH  
CLIP  
BOLT, .38-16 x 1  
NUT- FLG, .38-16  
PULLY-FLAT  
BELT GUIDE  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Instructions  
Sub-Frame Hitch  
NOTE: Please read through these instructions and the  
instructions of any other attachments before beginning  
installation.  
Change Pulley & Belt - Two-Stage Blower  
Only  
1. If using this hitch with a two-stage snowthrower, the  
front idler pulley must be switched from the right hand  
side of the hitch bracket, to the left, and an additional  
3/8 x 1 x 1/2 spacer (B, Figure 3) and 3/8-16 x 2-1/4  
capscrew (A) is required. Also install the 1703372  
drive belt.  
WARNING  
Before beginning any service work turn off the  
PTO, set the parking brake, turn off the ignition,  
and disconnect the spark plug wire(s).  
A
INITIAL ASSEMBLY  
Assemble Hitch  
1. Attach the support clamp (C, Figure 2) and hook  
assembly (B) to the hitch. Secure with four 5/16-18 x  
1 carriage bolts (A), washers (D), lockwashers (E),  
and nuts (F). Do not tighten the hardware at this  
time.  
B
F
E
F
B
C
D
Broadmoor /  
C
E
1600 / 2600  
Series  
Figure 3. Front Pulley - Two-Stage Applications  
D
A. Capscrew, 3/8-16 x 2-1/4  
B. Spacer, 3/8 x 1 x 1/2  
C. Belt Guide  
D. Washers, 3/8  
E. Lockwasher & Nut  
F. Pulley  
Assemble Push Bar Latch  
1. Attach Push Bar Latch (B, Figure 4), to hitch. Secure  
with four .31-16 x 1 bolts (A), and four .38-16 flange  
nuts (C).  
A
B
B
Conquest / 1700 /  
2700 &  
C
A
Prestige / 1800 /  
2800 Series  
C
A
Two Wheel  
D
Four Wheel  
Drive Models  
Drive Models  
E
Figure 4. Assemble Push Bar Latch  
F
A. Bolt, .38-16 x 1  
B. Push Bar Latch  
C. Flange Nut, .38-16  
Figure 2. Install Support Clamp  
A. 5/16-18 x 1 Carriage Bolt  
B. Hook Assembly  
D. 11/32 Washer  
E. 5/16 Lockwasher  
F. 5/16-18 Nut  
C. Support Clamp  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Sub-Frame Hitch  
Installation Instructions  
Snowthrower  
& Dozer  
Applications  
A
B
C
E
D
A
B
Figure 5. Assemble Lift Rod  
A. Lift Rod  
D
C
C. Spring  
B
B. Set Collar  
D. Rod Guide  
Mower  
Applications  
A
B
G
Figure 6. Early/Later Lift Links  
A. Early Model Lift Link  
B. Later Model Lift Link  
A
Assemble Lift Rod  
1. Install the set collars (B, Figure 4), spring (C), and  
rod guide (D) on the lift rod (A) as shown. Final  
adjustment of the set collars will be made after the  
hitch and attachment are installed.  
D
C
F
Figure 7. Connect Lift Link  
A. Pin  
B. Rear Hole of Lift Bar (Snowthrower Applications)  
C. Spacer  
INITIAL INSTALLATION  
Manual Lift Models  
D. Hair Pin Clip  
LIFT LINK - EARLY VS. LATER  
E. Upper Hole (Snowthrower Applications)  
F. Slot of Lift Link (Mower Applications)  
G. Lower Hole (Mower Applications)  
The early model lift link (A, Figure 6) was used on early  
production Conquest/1700/2700 Series tractors. It must  
be replaced with the later model lift link (B) included with  
this attachment. The later model link works in all appli-  
cations. Discard the early model link (A).  
LIFT LINK POSITION  
The lift link is installed differently depending on what  
attachment is being used. Refer to Figure 7 for link  
installation information.  
Hydraulic Lift Models  
1. Fully lower the hydraulic lift. The lift assembly is  
spring loaded so it will need to be held in the down  
position to perform of the following procedures.  
A
B
F
C
2. Remove and retain the flat head pin (B, Figure 8) and  
hair pin clip (E) securing the lift cylinder (A) to the lift  
shaft assembly (F). Remove and retain the flat wash-  
ers.  
D
E
Figure 8. Install Lock Plate - Hydraulic Lift Models  
A. Lift Cylinder  
D. Lock Plate  
B. Flat Head Pin (Original)  
C. Flat Head Pin (New)  
E. Hair Pin Clips  
F. Lift Shaft Assy.  
3. Mount the lock plate (D) next to the cams on the lift  
shaft assembly (F) as shown.  
5
4. Install the original flat head pin (B) and new flat head  
pin (C) and secure with hair pin clips.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Instructions  
Sub-Frame Hitch  
A
B
C
D
E
Figure 9. Install Hitch  
A. J-Hooks  
B. Hitch Rod  
C. Hitch Rod  
D. Hook  
E. Clamp Plate  
5. Push the clamp plate (D) backwards until it is snug  
against the lift shaft. Tighten the clamp plate hard-  
ware (E).  
Install Hitch  
1. Slide the hitch under the tractor.  
2. Raise the rear of the hitch and place the hook (C)  
over the lift shaft.  
3. Connect the front of the hitch to the tractor J-hooks  
(A, Figure 9) using the hitch rod (B) and a safety clip  
in the top holes of the push bar latch.  
4. Secure the front of the hitch to the tractor by attach-  
ing the hitch rod (C) and a safety clip in the bottom  
holes of the push bar latch.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Sub-Frame Hitch  
Installation Instructions  
D
A
B
C
A
B
C
Figure 11. Install Lift Rod - All Models  
A. Lift Lever  
B. Lift Rod  
C. Clip  
Figure 10. Install Lift Lever  
A. Lift Lever  
B. Lift Shaft  
C. Safety Clip  
D. Clevis Pin  
Install Lift Rod  
1. Slide the lift lever (A, Figure 10) onto the end of the  
tractor lift shaft (B) under the right side footrest.  
2. Use the tabs on the lift lever (A) to capture the tractor  
lift arm. Secure in place with a clevis pin (D) and  
safety clip (C).  
3. Insert the rear of the lift rod (B, Figure 11) into the  
bottom of the lift lever (A). Secure with a clip (C).  
Install Reflectors  
1. Install the two reflectors on the rear of the tractor seat  
deck.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Instructions  
Sub-Frame Hitch  
Snowthrower  
Position  
C
D
A
B
E
F
A. Hitch Rod  
B. Hitch Rod  
C. Lift Lever Extension  
D. Lift Link (Manual)  
E. Pressure Lock Plate  
(Hydraulic)  
F. Hook  
Figure 12. Normal Installation & Removal  
REMOVAL  
NORMAL INSTALLATION  
NOTE: After removing components, reinstall the clevis  
pins and clips to prevent loss.  
1. Insert the hook (F, Figure 12) into the back of the  
hitch. Mount the rear of the hitch on the lift cross-  
shaft.  
1. Disconnect the lift rod from the attachment and lift  
lever extension (C, Figure 12).  
2. Secure the front of the hitch to the J-hooks using the  
hitch rod (A) and (B) (Figure 9).  
2. Remove the clevis pin and clip from the lift lever (C)  
and remove the lift lever.  
3. Install the downward pressure lock plate (E) OR  
place the lift link (D) in snowthrower position.  
3. Remove the front hitch rod (A) and (B). Remove the  
hitch and hook (F).  
4. Install the lift lever extension (C).  
4. Remove the lock plate (E) OR reposition the lift link  
(D) in mowing position.  
5. Install the lift rod and attachment (Figure 11).  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Sub-Frame Hitch  
Installation Instructions  
Snowthrower  
& Dozer  
Applications  
Snowthrower  
& Dozer  
Applications  
E
A
A
B
C
D
F
E
D
C
B
Mower  
Applications  
Mower  
Applications  
G
A
A
B
F
E
D
C
F
G
Figure 13. Lift Lock Plate - Hydraulic Lift Models  
A. Lift Cylinder  
B. Flat Head Pin (Original)  
C. Flat Head Pin (New)  
D. Lock Plate  
Figure 14. Lift Link - Manual Lift Models  
A. Pin  
B. Rear Hole of Lift Bar (Snowthrower Applications)  
C. Spacer  
D. Hair Pin Clip  
E. Hair Pin Clips  
F. Lift Shaft Assy.  
G. Washers  
E. Upper Hole (Snowthrower Applications)  
F. Slot of Lift Link (Mower Applications)  
G. Lower Hole (Mower Applications)  
LIFT VARIATIONS WHEN USING  
ATTACHMENTS  
When a front-mounted attachment such as a snowthrow-  
er or dozer blade is used with the tractor, the lift mecha-  
nism must be locked to provide downward force. When  
the mower is reinstalled the downward pressure lock  
must be released so that the mower can float.  
Manual Lift Models  
Hydraulic Lift Models  
NOTE: These instructions apply to Conquest / 1700 /  
2700 Series tractors or Broadmoor / 1600 / 2600 Series  
tractors equipped with a lift lever kit.  
When using a snowthrower or dozer, the downward  
pressure lock plate (D, Figure 13) and an additional pin  
(C) is installed. These parts are included with the attach-  
ment. Note that the washers (G) are not used with the  
lock plate.  
The lift link is installed differently depending on what  
attachment is being used. Refer to Figure 14 for link  
installation information.  
When mowing, the downward pressure lock plate (D) is  
removed and replaced with two washers (G). The addi-  
tional pin (C) is also removed.  
Fully lower the hydraulic lift. The lift assembly is spring  
loaded so it will need to be held in the down position to  
perform of the following procedures.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Instructions  
Sub-Frame Hitch  
NOTES  
MANUFACTURING, INC.  
Form No. 1734116  
Rev. 10/2006  
500 N Spring Street / PO Box 997  
Port Washington, WI 53074-0997 USA  
© 2006 Briggs & Stratton, Inc. All Rights Reserved  
TP 200-4417-00-AT-SMAN  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Black Decker Lawn Sweeper NSW18 User Manual
Bolens Lawn Mower 111 162A User Manual
Bush Hog Lawn Mower TD 1100 User Manual
Dixon Lawn Mower 435068 User Guide
Land Pride Lawn Mower AFM4522 User Guide
McCulloch Lawn Mower P1292RB User Manual
Poulan Lawn Mower 184617 User Guide
Snapper Lawn Mower PN 7600028 User Manual
Snapper Lawn Mower V 21P User Manual
Woods Equipment Lawn Mower MX54T User Guide