Havis Shields Slide Out Trunk Tray 2006 2008 Chevrolet Impala C 3311 2 User Manual

INSTALL INSTRUCTIONS C-3311-2 & C-3311-18-2  
SLIDE-OUT TRUNK TRAY  
2006-2008 CHEVROLET IMPALA  
TOOLS REQUIRED:  
7/16” wrench  
Powered drill w/ 3/16” drill bit  
Ratcheting wrench  
Standard socket set  
Screwdriver set  
HARDWARE:  
QTY DESCRIPTION  
PART #  
12  
16  
12  
4
4
4
2
1
1
4
¼-20 x ¾” Hex head bolts  
¼” Flat washers  
¼-20 Serrated nuts  
8-32 x 3/8” Machine Screws  
8-32 Keps Nuts  
¼” x ¾” Hex head lag bolts (only on C-3311-18-2)  
Front Mounting Leg  
Rear Driver-side bracket  
Rear Passenger-side bracket  
Mounting plate w/ pem ¼” pem studs (Use 2 on C-3311-18-2)  
P.S. Front Mounting Bracket (only on C-3311-18-2)  
P.S. Rear Mounting Adapter Bracket (only on C-3311-18-2)  
GSM33001  
GSM31005  
GSM30023  
GSM33540  
GSM30027  
GSM33060-1  
CM001390  
CM001391  
CM001392  
CM001393  
CM001394  
CM93712  
1
1
Always!  
Read all instructions before installing any Havis-Shields Equipment Corp products.  
Check for obstructions (Wire, brake lines, fuel tank, etc.) before drilling any holes!  
Use hardware provided with install kit  
For product support, visit the Install Instructions Section of our website at  
SUB ASSEMBLY: (Use Iso views on page #1 & 2 for sub assemblies)  
- 1 -  
1. Attach forward mounting legs to the slide out tray.  
Attach forward mounting legs with provided 8-32 screws and hex nuts to slide track.  
The front legs will be square to the slide tray.  
On the front passenger side of the half tray, passenger side front mounting brackets  
(CM001394) will attach to the front mounting legs.  
2. Attach rear-mounting brackets to the slide out tray.  
Loosely attached the rear mounting brackets to the “Cradle Bracket” using ¼” x ¾”  
hex head bolts, washers and serrated nuts.  
On the rear passenger side of the half tray, passenger side rear mounting adapter  
bracket (CM93712) will attach to the rear mounting brackets.  
INSTALLATION:  
1. Mount slide tray in vehicle trunk.  
Slide trunk tray into vehicle with the tall front mounting legs in first. Prop up tray in  
position using block of wood.  
Once you have the tray square, and pushed to the forward most position in trunk,  
attach mounting brackets to vehicle using the supplied mounting plates.  
On the half tray, passenger side, you will bolt the passenger side front mounting  
brackets (CM001394) to the vehicle using ¼” x ¾” Hex head lag bolts. (Pre-drill w/  
3/16” drill bit)  
Position mounting plates into locations shown in photos #1 and 2.  
Loosely attach front and rear mounting brackets to mounting plates using ¼” serrated  
nuts.  
On the passenger side, attach passenger side rear mounting adapter brackets  
(CM93712) to vehicle using ¼” x ¾” hex head lag bolts. (Pre-drill w/ 3/16” drill bit)  
Forward Mounting Brackets  
Rear mounting brackets  
Mounting  
Plate  
Mounting  
Plate  
Photo #2  
Photo #1  
- 3 -  
C-3311-2^3311-18-2_INST_9-07  
Tighten all loose hardware.  
Be sure tray slides smoothly and locks in the closed position. If the tray does not slide  
smooth then most likely the tray is not square or level.  
#8 screws &  
hex nuts  
¼” bolts, washers,  
& nuts  
Photo #3  
- 4 -  
C-3311-2^3311-18-2_INST_9-07  

Brother intelli FAX 1270 User Manual
Brother Printer MFC J6710DW User Manual
Carrier 62DB User Manual
Clarion Automobile Accessories PN 2083D User Manual
Cornelius S1630 User Manual
Danby DAC12344DE User Manual
GE General Electric Air Conditioner AVE22 User Manual
Honeywell V5863A User Manual
HP Hewlett Packard DESKJET 1120C User Manual
Human Touch Automobile Accessories HT 270 User Manual