Model iH24
The Portable System
For Your iPod®
THIS UNIT WILL NOT CONTROL OR CHARGE 3G iPod
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Quick Start.................................................................................................................................................................... 1
Controls and Indicators / iH24 Display .................................................................................................................... 2
Using the iH24........................................................................................................................................................... 3-4
Replacing iH24 Backup Batteries ............................................................................................................................. 5
Install/Replace Batteries for Portable Use .............................................................................................................. 5
Using The Remote Control Unit ............................................................................................................................... 6
A Consumer Guide to Product Safety.........................................................................................................................7
Troubleshooting ...................................................................................................................................................... 8-9
Warranty Information ................................................................................................................................................10
Maintenance
Maintenance
•
•
Place the unit on a level surface away from sources of direct sunlight or excessive heat.
Protect your furniture when placing your unit on a natural wood and lacquered finish. A cloth or other protective material should
be placed between it and the furniture.
• Clean your unit with a soft cloth moistened only with mild soap and water. Stronger cleaning agents, such as Benzine, thinner or
similar materials can damage the surface of the unit.
FCC Information
This device complies with Part 15 of the FCC Rules, operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
This equipment complies with the limits for a Class B digital device as specified in Part 15 of FCC Rules. These limits
provide reasonable protection against radio and TV interference in a residential area.
However, your equipment might cause TV or radio interference even when it is operating properly. To eliminate
interference you can try one or more of the following corrective measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the distance between the equipment and the radio or TV.
Use outlets on different electrical circuits for the equipment and the radio or TV.
Consult your dealer or an experienced radio/television technician if the problem still exists.
Modifying or tampering with your system’s internal components can cause a malfunction and might invalidate the
system’s warranty and void your FCC authorization to operate it.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Download from Www.Somanuals.com. All Manuals Search And Download.
iH24 Quick start
1: AC power
3: Stand Feet
2: batteries
RESET
R E S E T
step: 2
step: 1
Connect AC adaptor cable to
jack on back of the IH24 and
plug the other end into a wall
socket to play and charge iPod.
For portable operation, open
battery compartment on the
bottom of the unit. Insert 4
Fold out the support stand feet
located on the bottom of the unit
“AA” (LR) batteries as indicated.
thin iPod with video (30 GB)
Use this insert
Insert 9
iPod touch 2G
insert 16
iPod nano 4G
insert 17
thin (30 GB) iPod with video
thin (80GB) iPod classic
For this iPod
iPod Touch 2G
iPod nano 4G
NOTE: If you do not have an insert
for your iPod, please visit
iHome toll free at 800-288-2792
to purchase one.
4: inserts
5: iPod
Select the dock insert for your
iPod® model from the table
below and place insert in dock.
Never dock an iPod without
the proper insert in place.
Insert iPod® into dock (iPod must
not be in a “skin” or case). When
connected to AC power, iPod will
charge while docked. Press the
iPod/play Button on the IH24 to
play your iPod.
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Controls and Indicators
Sleep / Minute Set Button ꢆ
ꢇ iPod Dock
ꢃ Alarm Reset/Power Off Button
Time Set Button ¶
Hour Set Button ¿
ꢈ iPod Play/Pause
Power ON Button
Snooze/Dimmer Button ³
ꢅ Alarm On-Off /Set Button
ꢄ Volume Up Button
¸ Volume Down Button
Back of Unit
Bottom of Unit
ꢂ Aux in Jack
Battery compartment
DC Jack ƹ
ꢀ DST Switch
ꢁ EXB Button
Travel Lock ƺ
Remote Control Switch
Stand Feet
iH24 Display
PM Indicator
Time/Alarm Display
Sleep Display
iPod Indicator
DST Indicator
Main Battery Low Indicator
Travel Lock Indicator
Alarm Armed
Clock Backup Battery Low Indicator
EXB Indicator
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the iH24
Connect iH24 to Power Source
a) Plug the AC adaptor cable into the AC Adaptor Jack and the other end into a standard 120v wall socket. Adaptor must be plugged
in to charge iPod.
b) For portable operation, install 4 “AA” (LR) batteries in battery compartment on the bottom of of the unit. Make sure polarity
matches diagram in compartments. Note: Unit will not charge iPod while operating on batteries.
Setting the Clock
a) Depending on your location and the time of year, move the DST (Daylight Saving Time) switch on the back of the unit to +1 to
add one hour (a DST icon
will appear on the display) or to -1 to subtract 1 hour.
b) Press and hold the Time Set Button
until the display flashes. Press the Alarm Set Button to toggle between 24 hour (military)
and 12 hour (standard) time display modes.
c) Press the Hour Set Button to adjust the hour display (a PM indicator appears when time is set to PM; there is no AM indicator)
d) Press the Minute Set Button to adjust the minute display. Hold to advance rapidly. When the correct time is displayed, press the
Time Set button
again. Two beeps will indicate clock setting is complete.
Using the Alarm
Setting the Alarm
a) Press and hold the Alarm Set Button
until the alarm time flashes to wake to iPod (buzzer alarm sounds if no iPod is detected).
b) Press the Hour Set Button to set the desired alarm hour (a PM indicator appears when time is set to PM; there is no AM
indicator)
c) Press the Minute Set Button to set the alarm minute time. When the desired alarm time is displayed, press the Alarm Set Button
again. Two beeps will indicate alarm setting is complete. Alarm is now armed, indicated by the alarm clock icon.
Arming and Disarming Alarm (Turn Alarm Function ON and OFF)
a) Press the Alarm On/Off Button to arm or disarm alarm functions. When armed, the alarm icon appears in the display.
Resetting the Alarm to Come on the Next Day
a) When the alarm is sounding, press the Alarm Reset/Power Off Button to stop the alarm and reset it to come on the following day.
Snooze
a) Press the Snooze/Dimmer Button after the alarm sounds. The alarm will be silenced and come on again 9 minutes later. Snooze
can be pressed several times during the 1 hour alarm cycle.
Sure Alarm
The iH24 has a sure alarm feature so the buzzer alarm will still sound in the event of power failure, if backup battery is installed.
iPod
Playing and charging your iPod
a) After selecting and placing the proper insert for your iPod model, gently dock iPod in Dock. When docked, iPod will charge until
fully charged when the iH24 is connected to an outlet with AC adaptor. Unit will not overcharge iPod.
b) Press the iPod Play Button
c) Press Volume UP or DOWN
to play iPod, and again to pause.
buttons to adjust iH24 volume up or down.
e) Press Alarm Reset/Power Off Button to turn iH24 and iPod off.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the iH24
Using Sleep Mode
•
Press the Sleep Button while the iPod is playing to enter sleep mode, and continue to press to step through the available sleep
times: 90, 60, 30 or 15 minutes. The sleep mode icon will appear on the display. The iH24 will play for the number of
minutes set, growing gradually softer until shutting off both the unit and the iPod at the set time. Press the Volume Up or
controls to set your own sleep volume. Sleep volume setting is separate from your alarm or regular listening volume
Down
selection.
Using the Aux in Jack
•
through the iH24 Aux in Jack (one end in the device’s line out or headphones jack, the other in the iH24 Aux in jack). Make
sure there is no iPod docked in the iH24 when using the Aux in jack. Press the iPod Play Button.
Using Dimmer
•
Press the Snooze/Dimmer Button during normal operation to adjust the brightness of LCD display. While operating on AC
current, the switch will toggle between high, medium, low and off settings. In battery mode, the display is off by default. Press
once to activate the display for about 3 seconds.
Using the Travel Lock
•
You can disable the iH24 controls to avoid turning on the device or changing settings while in transit and to save battery life
during extended periods of non-use. To do so, move the Travel Lock Switch (located on the back of the unit) to the Locked
icon position. A Lock Icon will appear on the display indicating the unit is locked and controls are inactive. Move the switch
to the Remote positon to restore normal function with remote control capability, or to the Off position to restore function with the
remote disabled.
Using the EXB Button
•
Press the EXB Button
located on the back panel of the unit to enable the EXB sound enhancement circuitry. This
circuitry is designed to provide a broader audio image with enhanced low range and mid range sound reproduction to bring
added life to compressed MP3 files. The EXB icon
disable the EXB effect.
will appear in the display when EXB is active. Press button again to
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing iH24 Backup Battery
Install/Replace Backup Battery
Battery install for
Clock display back up
The iH24 uses a backup battery system to provide continuous alarm operation and
clock settings in the event of a power failure. If the Backup Battery Low Icon located
on the right of the display is flashing, it is time to replace the backup batteries. Please
make sure the AC adaptor is connected, otherwise all settings may be lost during
battery replacement.
Open the battery compartment cover located on the back of the unit.
Insert 1 “CR2032” battery with the + facing out. Replace battery compartment cover.
Install/Replace Batteries for Portable Use
The iH24 uses 4 “AA” batteries for portable playing. If sound becomes weak or
distorted while operating on batteries, it’s time to replace the batteries.The iH24 will
not charge iPod while operating on batteries.
•
•
Open the battery compartment cover located on the bottom of the unit.
Insert 4 AA (LR) batteries in the compartment as indicated, making sure the
polarity (+ and -) matches the diagram.
•
Replace battery compartment cover.
Batteries information:
•
Do not mix old and new batteries.
•
Do not mix alkaline, standard (carbon -zinc) or rechargeable (nickel-cadmium)
batteries.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Using The Optional Remote Control Unit
Install/Replace the Remote Control Battery (for models with remote control)
The remote control battery is already installed at the factory. When the remote control
stops operating or its range seems reduced, replace the battery with a new one.
1. The battery door is located on the back end of the unit.
2. Slide the battery door to release the battery door latch and remove the battery door.
3. Insert a “CR2032” 3-volt lithium battery. Make sure the polarity (the + and – side of
the battery) is correct.
4. Replace the battery compartment door back in the remote control.
NOTE: PLEASE DISCARD BATTERIES PROPERLY
Operating the remote control
®
®
The Remote Control controls basic functions on the iH24 and certain iPod functions when the iPod is docked in the iH24.
For best results, aim remote control towards the remote sensor by the lower right corner of the display.
Move the Travel Lock Switch
to Remote position to enable the remote control.
alm. reset
OFF
Turns iH24 OFF or resets alarm when alarm is sounding
Volume Buttons raise and lower volume on the unit.
Skip to previous or next track when iPod is playing, or
hold to scan current playing track.
Selects iPhone/iPod and plays track. In play mode,
press to pause
sleep
mute
Selects Sleep Time function
Turn EXB sound enhancement ON or OFF
Toggles sound ON or OFF
snooze
Snooze mode when alarm sounds, otherwise dims display
6
Download from Www.Somanuals.com. All Manuals Search And Download.
A Consumer Guide to Product Safety
When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety. However,
improper use can result in potential electrical shock or fire hazards. Please read all safety and operating instructions
carefully before installation and use, and keep these instructions handy for future reference. Take special note of all
warnings listed in these instructions and on the unit.
1. Water and Moisture – The unit should not be used near water. For example: near a bathtub, washbowl, kitchen sink,
laundry tub, swimming pool or in a wet basement.
2. Ventilation – The unit should be situated so that its location or position does not interfere with its proper ventilation.
For example, it should not be situated on a bed, sofa, rug or similar surface that may block ventilation openings. Also,
it should not be placed in a built-in installation, such as a bookcase or cabinet, which may impede the flow of air
through the ventilation openings.
3. Heat – The unit should be situated away from heat sources such as radiators, heat registers, stoves or other appliances
(including amplifiers) that produce heat.
4. Power Sources – The unit should be connected to a power supply only of the type described in the operating
instructions or as marked on the appliance.
5. Power-Cable Protection – Power supply cables should be routed so that they are not likely to be walked on or
pinched by items placed upon or against them. It is always best to have a clear area from where the cable exits the
unit to where it is plugged into an AC socket.
6. Cleaning – The unit should be cleaned only as recommended. See the Maintenance section of this manual for
cleaning instructions.
7. Objects and Liquid Entry – Care should be taken so that objects do not fall and liquids are not spilled into any
openings or vents located on the product.
8. Attachments – Do not use attachments not recommended by the product manufacturer.
9. Lightning and Power Surge Protection – Unplug the unit from the wall socket and disconnect the antenna or cable
system during a lightning storm or when it is left unattended and unused for long periods of time. This will prevent
damage to the product due to lightning and power-line surges.
10. Overloading – Do not overload wall sockets, extension cords, or integral convenience receptacles as this can result
in a risk of fire or electric shock.
11. Damage Requiring Service – The unit should be serviced by qualified service personnel when:
A.
B.
C.
D.
the power supply cable or plug has been damaged.
objects have fallen into or liquid has been spilled into the enclosure.
the unit has been exposed to rain.
the unit has been dropped or the enclosure damaged.
E.
the unit exhibits a marked change in performance or does not operate normally.
12. Periods of Nonuse – If the unit is to be left unused for an extended period of time, such as a month or longer, the
power cable should be unplugged and batteries removed from the unit to prevent damage or corrosion.
13. Servicing – The user should not attempt to service the unit beyond those methods described in the user’s operating
instructions. Service methods not covered in the operating instructions should be referred to qualified service
personnel.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Symptom
Possible Problem
Solution
Unit doesn’t respond
(no power)
AC adaptor isn’t plugged into a wall outlet
or the connector is not plugged into the
power supply jack on the back of the unit
Plug the AC adaptor into a wall outlet and plug the
connector into the supply jack on the unit
Wall outlet is not functioning or switched off Plug another device into the same outlet to confirm the outlet
is working. Make sure any associated power switch is ON.
Batteries are weak or dead
Replace with new batteries
iPod does not dock
properly
Using no or wrong iPod insert
iPod not installed properly
Make sure the dock insert is the proper fit for your iPod
Remove your iPod from the dock and check for
obstruction on the connectors in the dock and on your
iPod. Make sure there is no “skin” or case on the iPod.
Then reseat it in the dock.
Battery Low icon
always flashing
Batteries are weak
Replace with new batteries
Batteries were not installed properly
Check to make sure the polarity ( + and – ends) matches
the diagram in the battery compartment
Unit must be running on AC power to charge iPod. It will not
charge your iPod when operating on battery power.
iPod does not
charge
Operating on battery power
Remove your iPod from the dock and check for
obstruction on the connectors in the dock and on your
iPod. Then reseat it in the dock.
iPod is not installed properly
Your iPod software is too old
iPod does not
respond to the unit
Upgrade software on your iPod via iTunes
iPod is locked up
Please make sure your iPod is working properly before
docking into the unit. Please refer to your iPod manual for
details.
Using 1st or 2nd generation iPod, iPod
shuffle or other devices.
iH24 cannot control those iPods or other devices.
Buttons/Controls
don’t work
Move Travel Lock to Off or Remote position
Press the Menu button on your iPod
Travel Lock is in Lock position
If your iPod is not used for some time, it
may enter deep sleep mode
iPod does not come
on immediately
iPod battery is too run down/weak
Charge your iPod for about 5 minutes
NOTE: THIS UNIT DOES NOT CONTROL OR CHARGE 3G iPod
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Symptom
Possible Problem
Solution
Unit doesn’t respond
(no power)
AC adaptor isn’t plugged into a wall outlet
or the connector is not plugged into the
power supply jack on the back of the unit
Plug the AC adaptor into a wall outlet and plug the
connector into the supply jack on the unit
Wall outlet is not functioning or switched off Plug another device into the same outlet to confirm the outlet
is working. Make sure any associated power switch is ON.
Batteries are weak or dead
Replace with new batteries
iPod does not dock
properly
Using no or wrong iPod insert
iPod not installed properly
Make sure the dock insert is the proper fit for your iPod
Remove your iPod from the dock and check for
obstruction on the connectors in the dock and on your
iPod. Make sure there is no “skin” or case on the iPod.
Then reseat it in the dock.
Battery Low icon
always flashing
Batteries are weak
Replace with new batteries
Batteries were not installed properly
Check to make sure the polarity ( + and – ends) matches
the diagram in the battery compartment
Unit must be running on AC power to charge iPod. It will not
charge your iPod when operating on battery power.
iPod does not
charge
Operating on battery power
Remove your iPod from the dock and check for
obstruction on the connectors in the dock and on your
iPod. Then reseat it in the dock.
iPod is not installed properly
Your iPod software is too old
iPod does not
respond to the unit
Upgrade software on your iPod via iTunes
iPod is locked up
Please make sure your iPod is working properly before
docking into the unit. Please refer to your iPod manual for
details.
Using 1st or 2nd generation iPod, iPod
shuffle or other devices.
iH24 cannot control those iPods or other devices.
Buttons/Controls
don’t work
Move Travel Lock to Off or Remote position
Press the Menu button on your iPod
Travel Lock is in Lock position
If your iPod is not used for some time, it
may enter deep sleep mode
iPod does not come
on immediately
iPod battery is too run down/weak
Charge your iPod for about 5 minutes
NOTE: THIS UNIT DOES NOT CONTROL OR CHARGE 3G iPod
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Troubleshooting
Symptom
Possible Problem
Solution
iPod didn’t charge
Make sure the iH24 is plugged into a working AC outlet to
charge your iPod
Operating iH24 on batteries. The iH24 only
charges iPod while operating on AC power
Remove your iPod from the dock and check for
obstruction on the connectors in the dock and on your
iPod. Then replace it in the dock.
iPod is not installed properly
Please make sure your iPod is working properly before
docking into the unit. Please refer to your iPod manual for
details.
iPod is locked up/ frozen
iPod battery has problem
Volume level is set too high
Sound is distorted
Decrease the volume
If the iPod original sound source (MP3) is of poor quality,
distortion and noise are easily noticed with high-power
speakers. Try a different audio source such as a music CD.
Sound source is distorted
If you are using an external sound source like older
generation of iPod, try reducing the output volume on the
device itself.
Try turning bass boost OFF on your iPod/sound source.
Replace current batteries with new ones
Batteries are weak
Remote Control is not pointed toward
the iH24 remote sensor or sensor is
blocked
Remote Control
didn’t work
Point the Remote Control toward the iH24, move within 10
feet of the unit, make sure sensor is unobstructed
Battery weak
Replace current battery with new battery
Move Travel Lock switch to Remote position
Travel Lock is in Lock or Off position
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited 90-Day Warranty Information
Home Products, a division of SDI Technologies Inc. (hereafter referred to as SDI Technologies), warrants this product to be free
from defects in workmanship and materials, under normal use and conditions, for a period of 90 days from the date of original
purchase.
Should this product fail to function in a satisfactory manner, it is best to first return it to the store where it was originally
purchased. Should this fail to resolve the matter and service still be required by reason of any defect or malfunction during the
warranty period, SDI Technologies will repair or, at its discretion, replace this product without charge (except for a $10.00
charge for handling, packing, return UPS/postage, and insurance). This decision is subject to verification of the defect or
malfunction upon delivery of this product to the Factory Service Center listed below. The product must include proof of
purchase, including date of purchase. The fee for service without proof of purchase is $30.00.
Before returning this product for service, please first replace the batteries (if applicable) with fresh ones, as exhausted or defective
batteries are the most common cause of problems encountered.
If service is still required:
1. Remove the batteries (if applicable) and pack the unit in a well padded, heavy corrugated box.
2. Enclose a photocopy of your sales receipt, credit card statement, or other proof of the date of purchase, if within the warranty
period.
3. Enclose a check or money order payable to the order of SDI Technologies, for the sum of $10.00 ($30.00 without proof of
purchase).
4. Send the unit prepaid and insured, to the Factory Service Center listed below.
Consumer Repair Department
SDI Technologies Inc.
1330 Goodyear Drive
El Paso, TX 79936-6420
Disclaimer of Warranty
NOTE: This warranty is valid only if the product is used for the purpose for which it was designed. It does not cover (i) products
which have been damaged by negligence or willful actions, misuse or accident, or which have been modified or repaired by
unauthorized persons; (ii) cracked or broken cabinets, or units damaged by excessive heat; (iii) damage to digital media players,
CD’s or tape cassettes (if applicable); (iv) the cost of shipping this product to the Factory Service Center and its return to the
owner.
This warranty is valid only in the United States of America and does not extend to owners of the product other than to the original
purchaser. In no event will SDI Technologies or any of its affiliates, contractors, resellers, their officers, directors, shareholders,
members or agents be liable to you or any third party for any consequential or incidental damages, any lost profits, actual,
exemplary or punitive damages. (Some states do not allow limitations on implied warranties or exclusion of consequential
damages, so these restrictions may not apply to you.) This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.
Your acknowledgment and agreement to fully and completely abide by the above mentioned disclaimer of warranty is contractually
binding to you upon your transfer of currency (money order, cashier's check, or credit card) for purchase of your SDI Technologies
product.
© 2009 SDI Technologies, Inc. All rights reserved
For any other questions: 1-800-288-2792 Toll Free
iH24-030209-A
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|