NOTE:
Please read all
instructions carefully
before using this product
Table of Content
Safety Notice
Hardware Pack
Assembly Instruction
Exploded Diagram
Parts List
MARCY
MWB-345 BENCH
Warranty
Ordering Parts
Model
MWB-345
Retain This
Manual for
Reference
02-25-05
OWNER'S
MANUAL
IMPEX INC.
14777 Don Julian Rd., City of Industry, CA 91746
Tel: (800) 999-8899 Fax (626) 961-9966
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE
OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES
NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED
BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
HARDWARE PACK
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTION
Tools required assembling the machine: Two Adjustable Wrenches and Allen
Wrenches. NOTE: It is strongly recommended two or more people assembling this
machine to avoid possible injury.
STEP 1
(SEE Diagram 1)
A.) Connect the two Rear Upright Beams (#1) by a Cross Brace (#15) in the Mid-span.
Secure them with two M10 x 2 3/8” Hex Bolts (#2), four ∅ ¾” Washers (#3), one
Bracket (#7), and two M10 Aircraft Nuts (#4) on each end of the Cross Brace.
B.) Insert the Backrest Adjustment Bar (#10) through a selected hole to obtain desired
incline of Backrest.
C.) Insert the two Bar Catches (#13) & (#14) into the selected hole on the Rear Upright
Beams (#1) to obtain the desired height to hold the weight bar.
DIAGRAM 1
4
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2
(SEE DIAGRAM 2)
A.) Connect the Front Stabilizer (#42) to the Main Seat Support (#52). Secure them with
two M10 x ¾” Hex Bolts (#46), four ∅ ¾” Washers (#3), and two M10 Aircraft Nuts (#4).
DO NOT tighten the nuts and bolts yet.
B.) Connect the Main Seat Support (#52) to the open bracket on the Cross Brace (#15).
Secure them with two M10 x 2 3/8” Bolts (#2), four ∅ ¾” Washers (#3), and two M10
Aircraft Nuts (#4).
C.) Connect one end of Diagonal Support (#43) to the Main Seat Support (#52). Secure it
with one M8 x 2 1/8” Hex Bolt (#48), two ∅ 5/8” Washers (#21) and one M8 Aircraft Nut
(#49). Connect the other end to the Front Stabilizer (#42). Secure it with one M8 x ¾”
Hex Bolt (#20) and ∅ 5/8” Washer (#21).
D.) Securely tighten all the nuts and bolts previously installed.
E.) Insert a Long Lock Pin (#53) into the hole on the Main Seat Support (52). NOTE: The
Pin is not designed to sustain any heavy weight. Only use the pin when changing the
backrest board to a vertical position when doing Walk-in-Squat from the rear.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3
(SEE DIAGRAM 3)
A.) Attach the Leg Developer (#38) onto the bracket on the Front Stabilizer (#42). Secure it
with an Allen Socket Axle (#44) and Allen Socket Screw (#45).
B.) Insert two Foam Roll Tubes (#39) halfway through the hole on the Leg Developer. Push
four Foam Rolls (#37) onto the Tube from both ends. Plug four Ø 1” Foam Roll End
Caps (#36) onto each end of the Tubes.
C.) Clip a Spring Clip (#34) onto the post on the Leg Developer.
D.) Attach the Arm Curl Handle Support (#54) to the Leg Developer. Secure it with a Short
Lock Pin (#8). Remove Pin when using the Leg Developer.
DIAGRAM 3
6
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4
(SEE DIAGRAM 4)
A.) Attach the hole-side of the Backrest Supports (#16) onto both ends of the Pivot on the
Main Seat Support (#52). The other side rest against the Backrest Adjustment Bar
(#10).
B.) Place the Backrest Board (#18) onto the Backrest Supports (#16). Secure it with four
M6 x 1 3/8” Hex Bolts (#50) and ∅ ½” Washers (#51).
C.) Place the Seat (#19) onto the bracket on the Main Seat Support (#52). Align the holes
and secure it with four M6 x 1 3/8” Hex Bolts (#50) and ∅ ½” Washers (#51).
D.) Attach the Arm Curl Pad (#23) to the Arm Curl Stand (#22). Secure it with two M8 x 5/8”
Hex Bolts (#20) and ∅ 5/8” Washers (#21).
E.) Insert the Arm Curl Stand (#22) into the opening on the top of the Front Stabilizer (#42).
Secure it with a Knob Bolt (#47).
DIAGRAM 4
7
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5
(SEE Diagram 5)
A.) Attach the ball end of the Cable (#27) to the Pulley (#28). Place the Pulley in the open
slot on the Lat Bar Frame (#31). Secure it with one M10 x 2 1/8” Hex Bolt (#32), two
Pulley Bushings (#29), two ∅ ¾” Washers (#3), and one M10 Aircraft Nut (#4).
B.) Slide the Weight Holder (#33) onto the Lat Bar Frame from the bottom. Connect the
Cable to the Holder with a Hook (#26).
C.) Connect the Lat Bar (#25) to the Cable with a Hook (#26). When using the Lat Pull
Down, remove the Arm Curl and place it one the storage post behind the Rear Upright
Beam. Then insert the Lat bar Frame into the opening on the Front Stabilizer.
DIAGRAM 5
8
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY NO.
DESCRIPTION
Rear Upright Beam
M10 x 2 3/8” Hex Bolt
∅ ¾” Washer
M10 Aircraft Nut
1 5/8” x 3 1/8” Square End Cap
1 ¼” Square End Cap
Bracket
QUANTITY
1
2
3
4
5
6
7
8
2
6
18
9
6
2
2
1
5
1
2
2
1
1
1
2
2
1
1
3
5
1
1
2
1
2
1
1
2
4
1
1
1
2
3
4
4
1
2
2
2
1
1
1
1
2
1
1
1
8
8
1
1
1
1
2
2
Short Lock Pin
9
∅ 1” Round End Cap
Backrest Adjustment Bar
Bar Catch Panel
∅ ¾” Bar Catch End Cap
Right Bar Catch
Left Bar Catch
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
Cross Brace
Backrest Support
1” Square End Cap
Backrest Board
Seat
M8 x ¾” Hex Bolt
∅ 5/8” Washer
Arm Curl Stand
Arm Curl Pad
Lat Bar Handle Grip
Lat Bar
Hook
Cable
Pulley
Pulley Bushing
1 ½” Square End Cap
Lat Bar Frame
M10 x 2 1/8” Hex Bolt
Weight Holder
Spring Clip
Sleeve
∅ 1” Foam Roll End Cap
Foam Roll
Leg Developer
Foam Roll Tube
Plastic Bushing
1 ¾” Square End Cap
Front Stabilizer
Diagonal Support
Allen Socket Axle
Allen Socket Screw
M10 x ¾” Hex Bolt
Knob Bolt
M8 x 2 1/8” Hex Bolt
M8 Aircraft Nut
M6 x 1 ½” Hex Bolt
∅ ½” Washer
Main Seat Support
Long Lock Pin
Arm Curl Handle Support
Arm Curl Handle
Arm Curl Handle Grip
Ø 1 ½” Spacer
10
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPEX INC.
LIMITED WARRANTY
IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal
use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty
extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or
repairing, at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Customer
Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be prepaid by the
customer. This warranty does not extend to any product or damage to a product caused by or attributable to
freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by a IMPEX authorized
service center or for products used for commercial or rental purposes. No other warranty beyond that
specifically set forth above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in connection
with the use or performance of the product or other damages with respect to any economic loss, loss of
property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other
consequential damages or whatsoever natures.
Some states do not allow the exclusion or limitation of
incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state to state.
IMPEX INC.
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-999-8899
during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific standard time.
When ordering replacement parts, always give the following information.
1.
2.
3.
4.
Model
Description of Parts
Part Number
Date of Purchase
11
Download from Www.Somanuals.com. All Manuals Search And Download.
|