ICE 35, ICE 45, ICE 55
Installation and Operations Manual
531611-1_C
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
How Sonar Works
1
4
5
6
How Ice Flashers Work
Installation Overview
ICE Flasher Series™ Base Assembly
1. Assembling the Transducer Storage Posts .............................................................. 6
2. Assembling the Base and Handle............................................................................ 7
3. Assembling the Control Head to the Base and Handle.......................................... 8
ICE Flasher Series™ Assembly
9
1. Connecting the Power Cable.................................................................................... 9
2. Charging and Installing the Battery ........................................................................ 9
3. Assembling the Portable Bag (ICE 45/55 Only)......................................................11
Transducer Installation
12
1. Testing the Transducer Prior to Installation............................................................12
2. Assembling the Transducer and Float ....................................................................12
3. Connecting the Transducer Cable ..........................................................................14
4. Storing the Transducer ............................................................................................15
Test and Finish the Installation
16
17
Getting Started - Using Your ICE Flasher Series™ Fishfinder
Powering Up the Control Head....................................................................................18
Simulator........................................................................................................................18
What’s on the Flasher Dial ..........................................................................................18
What’s on the Display ................................................................................................ 20
Key Functions
20
Power/Range Dial........................................................................................................ 21
Selection Dial .............................................................................................................. 22
Zoom ............................................................................................................................ 23
Download from Www.Somanuals.com. All Manuals Search And Download.
iii
Gain .............................................................................................................................. 24
Noise Rejection............................................................................................................ 25
Beam ............................................................................................................................ 26
Color (ICE 55 Only) ...................................................................................................... 27
Palette 1 (ICE 35/45/55).......................................................................................... 27
Palette 2 (ICE 55 Only) ............................................................................................ 28
Palette 3 (ICE 55 Only) ............................................................................................ 29
Target (ICE 55 Only) .................................................................................................... 30
Dual Mode Key Functions .......................................................................................... 31
Maintenance
32
ICE Flasher Series™ Maintenance ............................................................................ 32
Transducer Maintenance ............................................................................................ 32
Troubleshooting
33
ICE Flasher Series™ Fishfinder Doesn't Power Up.................................................... 33
No Bottom Reading on the Display............................................................................ 33
No Continuous Depth Display in Very Shallow Water.............................................. 33
Screen Fades, Images are Not Sharp ........................................................................ 33
2-Year Limited Warranty
34
35
Humminbird® Service Policy
Returning Your Unit for Service.................................................................................. 36
Specifications
37
40
Contact Humminbird®
NOTE: Some features discussed in this manual require a separate purchase, and some
features are only available on certain models. Please read the manual carefully in order to
understand the full capabilities of your model. You can visit our website at
www.humminbird.com to order accessories online or contact our Customer Resource
Center at 1-800-633-1468.
Download from Www.Somanuals.com. All Manuals Search And Download.
iv
HOW SONAR WORKS
Sonar technology is based on sound waves. The ICE Flasher Series™ Fishfinder uses
sonar to locate structure, bottom composition, as well as depth directly below the
transducer. Your ICE Flasher Series™ Fishfinder consists of two components: the control
head and the transducer. The control head contains the transmitter and receiver, as well
as the user controls and display. The transducer is suspended beneath the water,
underneath the ice, and converts electrical energy from the transmitter into mechanical
pulses or sound waves. The transducer also receives the reflected sound waves and
converts them back into electrical signals for display on the Flasher Dial.
NOTE: The transducer must be submerged in water for reliable transducer detection. The
bottom of the transducer should be even with the bottom of the ice or hang slightly below
the bottom of the ice.
Your ICE Flasher Series™ Fishfinder sends a sound wave signal and determines distance
by measuring the time between the transmission of the sound wave and when the
sound wave is reflected off of an object; it then uses the reflected signal to interpret
depth, size, and composition of an object.
Sonar is very fast. A sound wave can travel from the surface to a depth of 240 ft (70 m)
and back again in less than 1/4 of a second.
SONAR is an acronym for SOund and
NAvigation Ranging. Sonar utilizes precision
sound pulses or “pings” which are emitted
Real Time Sonar
into the water in a teardrop-shaped beam.
Instant Display
The sound pulses “echo” back from objects
in the water such as the bottom, fish and
other submerged objects. The returned
echoes, or signals, are displayed as colored
lines on the Flasher Dial.
Download from Www.Somanuals.com. All Manuals Search And Download.
1
When all the echoes are viewed within
the beam, an easy to interpret multicolor
palette of sonar return signals appears
on the Flasher Dial. The ICE Flasher
Series™ Fishfinder plots the depth and
intensity of sonar returns from the
bottom, fish and structure.
The sound pulses are transmitted at
various frequencies depending on the
application. Your ICE Flasher Series™
Fishfinder gives you the power to choose
the frequency and coverage of your
sonar. 455 kHz provides narrow coverage
with the greatest definition. 240 kHz
provides wider coverage and a good
balance between depth performance
and resolution.
The power output is the amount of energy
generated by the sonar transmitter. It is
commonly measured using two methods:
• Root Mean Square (RMS) measures
power output over the entire transmit
cycle.
• Peak to Peak measures power output
at the highest points. The benefits of
increased power output are the ability
to detect smaller targets at greater
distances, ability to overcome noise,
and enhanced depth capability.
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Your ICE Flasher Series™ Fishfinder uses
selectable dual-frequency sonar with a wide
area of coverage. Selectable dual-frequency
gives you the option of two beams, and both
beams will cover the bottom and provide high
definition. The 9 degree center beam provides
the highest definition, while the 19 degree beam
provides wider coverage. Depth capability is
affected by such factors as bottom hardness,
water conditions, and transducer installation.
Whether fishing in shallow to very deep water,
in both fresh and salt water, selectable
dual-frequency is ideal for a variety of conditions.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
HOW ICE FLASHERS WORK
Although the sonar part of an ICE Flasher Series™ Fishfinder works in the same way as
any other Humminbird® control head, the return signal is displayed differently. The ICE
Flasher Series™ LCD is modeled on the original analog displays and represents what is
happening below the transducer the moment it happens. The Flasher Dial displays a
multicolor palette indicating low to high sonar intensity returns, where red indicates high
intensity and green indicates low intensity. See Color Palettes for more information.
Read the Flasher Dial
in a Clockwise Direction
Algae and Other
Surface Vegetation
Close to
Surface of
the Water
Strong Sonar Return
Signal (bottom)
Medium Sonar
Return Signal
(fish)
Depth Reading
Weak Sonar Return
Signal (jig)
When fish swim into the area below the transducer, the new sonar return signal is
immediately displayed on the Flasher Dial. Depending on the size of the fish and its
closeness to the transducer, the sonar return will be displayed as a weak, medium, or
strong sonar signal.
In the above example, the sonar return signal from the jig is displayed as a weak signal
(green), the fish is displayed as a medium signal (yellow), and the bottom composition
is displayed as a strong signal (red). When the fish swims towards your jig, you can see
the activity instantly on your Flasher Dial. Also, the Active Display shows that the ICE
45/55 Flasher is reading the depth of 18.3 feet to the bottom.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
INSTALLATION OVERVIEW
Before you start installation, we encourage you to read these instructions carefully
in order to get the full benefit from your ICE Flasher Series™ Fishfinder. You will
assemble your control head first, then assemble and install your transducer. When
you are done with both of these installation tasks, you should perform a final
installation test before operating your ICE Flasher Series™ Fishfinder.
Please make sure that the following parts are included for your ICE Flasher Series™
control head:
• ICE Flasher Series™ control head
• Portable base and handle
• Power cable, battery, battery charger, and connecting hardware
• Flasher Bag (ICE 55 only)
Also, please make sure the following parts are included for your transducer:
• Ice Fishing transducer with 8' of signal cable
• Float, 40" of support cable, and support clip
• Cable clamps.
In addition to the hardware supplied, you will need a Phillips-head and a flat-head
screwdriver for installation and operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
ICE FLASHER SERIES™ BASE ASSEMBLY
Perform the following high-level steps by following the instructions in each numbered
section to assemble the ICE Flasher Series™ base assembly:
1. Assembling the transducer storage posts
2. Assembling the base and handle
3. Assembling the control head to the base and handle
1.Assembling the Transducer Storage Posts
In this procedure you will install the posts to hold the transducer cable.
Nut
Keyed Space of
Cable Retention Arm
Storage Post
Cable Retention
Arm, facing out
Spring
Flat Head Screw
1. Slide one spring over each flat-head screw and set aside.
2. Insert a nut into the keyed space of each cable retention arm. Push down on the
nut until it is flush with the surface of the cable retention arm.
3. Slide one cable retention arm over one storage post so that the arm faces out.
4. Hold the cable retention arm in place, and turn the base upside down.
5. Drop the assembled screw and spring straight into the back of the storage post.
Using a flat-head screwdriver, push down on the screw, and tighten.
6. Repeat steps 2-5 for the second cable retention arm.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
2.Assembling the Base and Handle
In this procedure, you will install the handle onto the base, and attach the tie-down
straps that will be used to secure the battery to the base in a later procedure.
1. Install the handle onto the base, so that the curved part of the handle faces
towards the back of the base, towards the battery well. Use the four included
#8-32 x 7/16" screws, two on each side, to attach the handle to the base (see the
illustrations Installing the Handle Onto the Base and Sliding in the Handle).
Hand tighten only!
Installing the Handle Onto the Base
Sliding in the Handle
NOTE: The handle is keyed so that it only fits onto the base in one direction.
2. Turn the base upside down, then thread the two included battery tie-down straps
from the bottom of the base up through each side of the battery well, using the
strap holes (see the illustration Attaching the Battery Tie-Down Straps).
Attaching the Battery Tie-Down Straps
Battery
Tie-down Straps
Download from Www.Somanuals.com. All Manuals Search And Download.
7
3.Assembling the Control Head to the Base and Handle
In this procedure you will install the ICE Flasher Series™ control head to the
base/handle assembly.
1. Place the control head into the gimbal bracket located on the base.
2. Place the 1" diameter black washers as shown in the figure; then, thread the
gimbal knob through the bracket and washers, into the housing. Tighten the
gimbal knob to secure the ICE Flasher Series™ control head to the mount.
3. Repeat step 2 for the other side.
Washer
Knob
Washer
Base Arm
Download from Www.Somanuals.com. All Manuals Search And Download.
8
ICE FLASHER SERIES™ ASSEMBLY
In this procedure you will connect the power cable to the control head and install the
base/handle assembly into the portable bag.
1.Connecting the Power Cable
1. Insert the power cable into the back of the control head. The slots for the plugs
are keyed to prevent reverse installation.
2.Charging and Installing the Battery
1. Charge the battery, using the included battery charger, until it is fully charged.
Charging usually requires 8 continuous hours but may vary depending on your
configuration. The LED on the charger will turn green when the battery is
fully charged.
NOTE: Some international models may not include a battery or battery charger.
NOTE: The battery charger uses a yellow LED to indicate it is charging. On some models,
this light might appear closer to orange than yellow. When this happens, the battery is still
charging properly and should be left to charge until the LED becomes green.
CAUTION: Do not pull on the battery or charger cables when you are trying to connect
them to or disconnect them from the battery terminals. Push or pull gently on the spade
terminals instead. If the connector feels tight, use a slight wiggling motion to slide the
spade connector into place on the terminal.
2. Center the battery on top of the foam pad.
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Spade
Terminals
Battery
Foam Pad
NOTE: Do NOT connect the power cable to the battery at this time. You should
wait until just before fishing to connect the power cable to the battery.
3. Move the tie-down straps out of the way so that the battery well is fully accessible.
4. Hold the foam pad and the battery together, and slide them into the battery well.
Make sure that the spade terminals are on the left side of the battery well and
the foam pad fits evenly around the battery well edges.
Installing the Battery
Tying Down the Battery
5. Pull the two battery tie-down straps over the top
of the battery and connect both ends of each
strap over the top. Make sure that the straps
are pulled tight around the battery and that the
battery is seated securely in the battery well.
6. Slide the Battery Terminal Adapter over each
spade terminal.
NOTE: The Battery Terminal Adapter allows you to power
your control head and charge it at the same time.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
3.Assembling the Portable Bag (ICE 55 Only)
In this procedure, you will install the ICE 55 Flasher into the portable bag. The portable
bag is not included with ICE 35/45 Flashers.
1. Unzip the largest opening on the front of the portable bag.
2. Insert the base/handle assembly into the portable bag, so that the Flasher Dial is
facing out of the bag. For best results, pull the bag over one shoulder of the
handle at a time.
3. Adjust the bag so that you can easily grab the handle, through the fabric
handhold inset, from the outside top of the portable bag.
Installing the Base
into the Bag
Pulling the Bag
over the Handle
Holding the
Portable Bag
Download from Www.Somanuals.com. All Manuals Search And Download.
11
TRANSDUCER INSTALLATION
Perform the following high-level steps by following the instructions in each numbered
section to install the transducer.
1. Testing the transducer
2. Assembling the transducer and float
3. Connecting the cable
1.Testing the Transducer Prior to Installation
Prior to installation, test the transducer to make sure that no damage occurred during
shipping.
1. Connect the transducer to the control head. The slots are keyed to prevent reverse
installation, so be careful not to force the connector into the holder.
2. Drop the transducer into the ice hole. If the transducer is working properly, you
will see the bottom displayed on the Flasher Dial as a red line.
WARNING: Before walking onto the ice, make sure that conditions are safe.
2.Assembling the Transducer and Float
In this procedure you will assemble the transducer and float.
Attaching the Float to
the Support Cable
Threading Support
Cable through
Support Clip
1. Thread the support cable through
the support clip and then clip onto
the transducer.
2. Attach your transducer float to the
support cable by sliding the support
cable through the slit in the float.
Float
Signal
Cable
NOTE: Attaching the float is optional. You
can also use the storage posts to hold the
support cable in position.
Support
Cable
Support
Cable
Cable
Support
Clip
Transducer
Download from Www.Somanuals.com. All Manuals Search And Download.
12
3. Position the float so that the transducer will be submerged in the water, just
below the ice.
Ice Layer
Float
Transducer
NOTE: The transducer must be submerged in water for reliable transducer detection. The
bottom of the transducer should be even with the bottom of the ice or hang slightly below the
bottom of the ice.
Attaching the Cable Clamps
4. Once you know where you want to
position your float, place one of the cable
clamps onto the support cable, above the
float. Use the inside, smaller cable hole
for the support cable so that the float will
not move, and so that the transducer will
maintain its position under the ice. Make
sure that the support cable is taut, so that
the transducer hangs straight down (see
illustration).
Cable Clamp
(acts as a stop for the
support cable, sets depth
of transducer in ice hole -
see Procedure 2, step 4)
Signal
Cable
Support
Cable
Cable Clamp
Cable Clamp
(provides cable
management for
signal cable - see
Procedure 2, step 5)
Support Cable Hole
Signal Cable Hole
5. If you would like to keep the support and
signal cables together above the float
stop, attach a cable management clamp
(included) to the support cable (using
the inner, smaller hole) and the signal
cable (using the outer, larger hole).
Make sure that the signal cable has
some slack so that it is not bearing the
weight of the transducer.
Signal
Cable
Support
Cable
Download from Www.Somanuals.com. All Manuals Search And Download.
13
3.Connecting the Transducer Cable
This section covers how to connect your transducer cable to your control head.
NOTE: If you have an ICE 55 Flasher, remove the control head and base from the portable
bag first.
1. Insert the transducer cable into the appropriate terminal slot on the rear of the
control head.
NOTE: The slots are keyed to prevent reversed installation, so be careful not to force the
connector onto the holder.
2. Route the transducer signal cable beneath the control head and secure to cable
clips on the base.
Connecting to the ICE Flasher Series™ Fishfinder
Transducer
Signal Cable
Cable
Clips
3. Reinstall assembled control head, base, and transducer into portable bag
(ICE 55 only).
Download from Www.Somanuals.com. All Manuals Search And Download.
14
4.Storing the Transducer
When you are done fishing, store the transducer using the following guidelines:
1. Wipe the cable dry.
2. Tuck the float under the control head, and wrap the cable around the storage
posts. Store the transducer in the transducer well.
NOTE: You do not have to detach the transducer cable from the control head to store
the transducer.
CAUTION: Although the transducer signal cable is designed to be flexible in cold
temperatures, you must store your cable correctly to avoid stressing it. Make sure it is
coiled smoothly, with no kinks, and that it is clear of the zippers on the portable bag.
Storing the Transducer
Cable Wrapped
Around Storage
Posts
Float Tucked
Under Control
Head
Transducer Well
Download from Www.Somanuals.com. All Manuals Search And Download.
15
TEST AND FINISH THE INSTALLATION
Once you have assembled both the ICE Flasher Series™ control head and the Ice Fishing
transducer, and have routed all the cables, you should perform a final test. Testing
should be performed with the transducer in the water.
1. After connecting the transducer to the control head, and confirming that the
power cable is connected to the battery, drop the transducer into the ice hole to
confirm proper operation.
WARNING: Before walking onto the ice, make sure that conditions are safe.
2. Turn the Power/Range dial to A (Auto) or x1 to power-on the control head.
NOTE: If the unit does not power up, make sure that the connector is fully seated in the
back of the control head, the power cable is connected to the battery, and the battery is
charged.
3. If all connections are correct and power is available, the Humminbird® control
head will enter Normal operation, and you should see the bottom on the control
head display.
4. If the bottom is visible on-screen with a digital depth readout, the unit is working
properly (ICE 35 will only display the bottom on the Flasher Dial).
NOTE: The transducer must be submerged in water for reliable transducer detection. The
bottom of the transducer should be even with the bottom of the ice or hang slightly below
the bottom of the ice.
Download from Www.Somanuals.com. All Manuals Search And Download.
16
GETTING STARTED -
USING YOUR ICE FLASHER SERIES™ FISHFINDER
Your ICE Flasher Series™ interface is easy to use. A combination of keys and special
features allows you to control what you see on the Flasher Dial and Active Display. Refer
to the following illustration, and see Key Functions for more information.
4
3
1
5
6
7
8
9
2
10
Flasher Dial
Zoom Key
Gain/Backlight Key (ICE 45/55)
Noise/Units Key (ICE 45/55)
Beam/Battery Key
1
2
6
7
Range Scale (ICE 35)
Active Display (ICE 45/55)
8
Selection Dial
3
4
5
9
Color Key (ICE 55)
Target Key (ICE 55)
Power/Range Dial
10
Download from Www.Somanuals.com. All Manuals Search And Download.
17
POWERING UP THE CONTROL HEAD
Power-on your ICE 35/45/55 Flasher by turning the Range/Off dial to any range
setting. The ICE Flasher Series™ Fishfinder will immediately enter Normal operation,
and the sonar return signals from the bottom will be displayed on the Flasher Dial.
SIMULATOR
Use the Simulator to learn how to use your ICE Flasher Series™ Fishfinder before
taking it out on the ice. The Simulator is a very powerful tool that simulates
on-the-water operation, providing a randomly-updated display. We recommend
going through this manual while using the Simulator, since all of the menus function
the way they actually do when in Normal operation.
To begin Simulator mode, hold down the Selection dial while powering on the
control head.
Exit the Simulator by powering your ICE 35/45/55 off.
WHAT’S ON THE FLASHER DIAL
The ICE Flasher Series™ Fishfinder uses a backlit circular display, together with a
multi-button keypad, to control all user functions. In addition, multiple color palettes
are available, depending on your model.
Sonar return signals are displayed as colored lines on the Flasher Dial. The color and
thickness of the lines reflect the strength of the sonar return or the size and density
of the object. In addition, multiple color palettes are available, depending on your
model. All Humminbird® ICE Flasher Series™ Fishfinders provide a multicolor palette,
where red = strong, yellow = medium, and green = weak sonar return signals. If you
have a high-end ICE 55 Flasher, you will also have the choice of 2 additional color
palettes. The color palette you have selected will determine the appearance and
significance of the individual color lines that appear on the Flasher Dial.
NOTE: The location of an object in relation to the transducer can influence how it appears
on the Flasher Dial. For example, a large object might display as a weak sonar return signal
if it is located on the outer edges of the transducer beam, where as a small object located
at the top of the transducer beam might display as a strong sonar return signal.
Download from Www.Somanuals.com. All Manuals Search And Download.
18
1
3
2
7
6
5
4
1
2
Zero: Indicates the start of the dial and represents the surface of the water, or the top of the water column.
Reading Direction: Read the dial in a clockwise direction. The top of the Flasher Dial represents the top of
the water column, and as you read further around the dial, you are reading deeper into the water column.
3
4
Sonar Return Signals Close to Zero: These lines indicate minor activity close to the surface of the water
such as air bubbles, algae, seaweed, or turbulence.
Sonar Return Signals Displayed between Zero and Bottom: These sonar return signals can indicate your
jig, bait fish, and other fish swimming into the water column. The color of the lines, indicating the strength of
the sonar return signal, will vary depending on the size and density of the objects.
5
6
7
Sonar Return Signals Close to Bottom: The sonar return signal lines that are displayed near the bottom
can indicate softer return signals such as from vegetation, mud, or sand at the bottom of the water column.
BottomLine:Bottomisusuallyindicatedbyathickredline.Becausethebottomisoftenadense,hardobject,
it will create a strong sonar return signal.
Depth: Shown in this example as 17 feet, the depth is continuously updated and can be read from the first
line of the bottom sonar return signal.
Download from Www.Somanuals.com. All Manuals Search And Download.
19
WHAT’S ON THE ACTIVE DISPLAY (ICE 45/55 ONLY)
Your ICE Flasher Series™ control head sends a sound wave signal and determines
distance by measuring the time between the transmission of the sound wave and when
the sound wave is reflected off of an object.
As your Ice Fishing transducer receives sonar signals, it converts them to a digital depth
that is shown on the ICE Flasher Series™ Active Display. The depth reading is
continuously updated. At initial power-up, the unit will begin normal operation and
display the digital depth and the units of measure. The liquid crystal display (LCD), or
Active Display, offers sharp viewing, even in bright, direct sunlight, and is continuously
lit for nighttime operation. The figure below shows the many features that are available
on the Active Display and where each feature will be displayed when you activate it.
NOTE: Actual depth capability depends on such factors as bottom hardness, water conditions, and
transducer installation. Units will typically read to deeper depths in fresh water than in salt water.
Voltage
Target
Backlight
Depth
Feet/Meter
2 Beams
Gain
Zoom
Noise Reject
Color
NOTE: The Active Display is available on ICE 45/55 Flashers only, and certain features are only
availableontheICE55. Readthismanualcompletelytounderstandthefullcapabilitiesofyourmodel.
KEY FUNCTIONS
Your ICE Flasher Series™ Fishfinder uses a number of keys to control the Range, Zoom,
Gain, Noise, Beam, and Color Palette functions. While in normal operating mode, press
a function key, such as Gain, turn the Selection dial to choose a setting for that function,
then press the Selection Dial to complete your selection.
Download from Www.Somanuals.com. All Manuals Search And Download.
20
POWER/RANGE DIAL
Use the Power/Range dial to power-on the ICE Flasher Series™
control head and to also set the depth range.
1. To Power-On the Control Head: Turn the Power/Range dial
from Off to any of the Depth Range settings.
2. To Set the Depth Range: Turn the Power/Range dial to A,
x1, x2, x4, or x10. (A, x1, x2, x4, x10)
Auto Range: Selecting A (Auto) will tell the unit to automatically choose the best range
based on the actual depth of the bottom. A (Auto) setting is not available on the ICE 35.
Auto Ranges available (ICE 45 and 55 only)
0 - 20 ft
0 - 40 ft
0 - 60 ft
0 - 80 ft
0 - 100 ft
0 - 120 ft
0 - 200 ft
10m
20m
30m
40m
60m
80m
100m
Manual Ranges: Selecting a manual range allows you to choose a specific range. For
example, if you only want to read sonar returns up to 80 feet or 40 meters in depth, set
the manual range to x4.
Manual Ranges
x1
x2
0 - 20 ft
0 - 40 ft
0 - 80 ft
0 - 200 ft
10m
20m
x4
40m
x10
100m
NOTE: The maximum range setting should not exceed the actual depth to the bottom.
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Range scales for the ICE 35 are shown below:
Outer Ring: x1 and x10.
When set to x10, add 0
behind numbers shown
on ring
Middle ring: x2 Scale
Inner ring: x4 Ring
SELECTION DIAL
The Selection dial allows you to set levels for the many functions on
your ICE Flasher Series™ control head. To use the Selection dial:
Press a function key, such as Gain. Then, turn the Selection dial to
choose a setting for that function. Press the Selection dial to
complete your selection.
NOTE: If you turn the Selection dial without pressing a function key
first, it will default to the Gain function.
Download from Www.Somanuals.com. All Manuals Search And Download.
22
ZOOM
When you use the zoom feature, your ICE Flasher Series™ Fishfinder will
display a 2x magnified view of the area you choose. The zoomed view will
display on the right side of the Flasher Dial between two blue lines. The normal view
will display on the left side of the Flasher Dial. (2x, Default = Off)
1. Press the Zoom key. Two blue zoom lines will display on the Flasher Dial, which
indicate that your Flasher Dial is in zoom mode.
2. Turn the Selection dial to move the zoom lines to the area you want to magnify.
The zoomed view will be shown on the right side of the Flasher Dial between the
two blue zoom lines. On the ICE 45/55 Flasher, the tick marks shown on the Active
Display show the zoom area.
• Exit zoom by pressing the Zoom key.
• Zoom can be dynamically updated after making your initial selection by turning
the Selection dial to a new location.
• When you are in zoom mode, in a 10m scale, 1/2 meters are represented by a
dash (for example: 2— = 2 1/2)
NOTE: If you do not press the Selection dial within 5 seconds of pressing the Zoom key or
turning the Selection dial, the zoom select function will time out.
Flasher Dial in Zoom Mode
Normal View
Zoom Line
(upper range)
(reading the full
depth of the
water column)
Zoom Line
(lower range)
Zoom View
Displays 2x
Magnification
of Zoom Field
Tick Marks Display
Zoom Area
(ICE 45/55)
Download from Www.Somanuals.com. All Manuals Search And Download.
23
GAIN
Gain controls how much the return sonar signal is amplified; the
preferred setting depends on the conditions in the water under your
transducer. Increase the gain to see more of what is below the transducer, and
decrease the gain to reduce clutter on the screen. High gain levels should only be
necessary in deeper water or to see smaller objects.
1. Press the Gain key.
2. Turn the Selection dial to choose a particular gain setting, then press the
Selection dial to complete your selection.
NOTE: If you do not press the Selection dial within 5 seconds of pressing the Gain key or
turning the Selection dial, the gain select function will time out.
NOTE: If your control head beeps repeatedly as you turn the Selection dial, you have
reached the lowest or highest level possible for the Gain.
Gain Setting
Gain Setting
ICE 35
ICE 45/55
The Gain setting is displayed as
a narrow or wide blue line at the
top of the Flasher Dial. (1 - 25,
where Narrow = 1, and Wide = 25;
Default = 16)
The Gain setting is shown on the
Active Display. (1 - 25, Default = 16)
NOTE: If you turn the Selection dial without pressing a function key first, it will default to
the Gain function.
Download from Www.Somanuals.com. All Manuals Search And Download.
24
NOISE REJECTION
Noise Rejection allows you to reduce cross-talk interference from
neighboring fishfinders that are operating on the same frequency as your
ICE Flasher Series™ Fishfinder.
If two nearby units are operating on the same frequency, your ICE Flasher Series™
Fishfinder display might show results from the neighboring fishfinder.
NOTE: Your other option is to use the Beam key to switch to a different operating
frequency (see Beam for more information).
1. Press the Noise key.
2. Turn the Selection dial to choose a particular noise rejection setting, then press
the Selection dial to complete your selection.
NOTE: If you do not press the Selection dial within 5 seconds of pressing the Noise key or
turning the Selection dial, the noise select function will time out.
NOTE: If your control head beeps repeatedly as you turn the Selection dial, you have
reached the lowest or highest level possible for the Noise Rejection.
Noise Rejection Setting
Noise Rejection Setting
ICE 35
ICE 45/55
The Noise Rejection setting is
displayed as a narrow or wide blue
line at the top of the Flasher Dial.
(1 - 10, where Narrow = 1, and
Wide = 10; Default = 6)
The Noise Rejection setting is
shown on the Active Display. (1 - 10,
Default = 6)
Download from Www.Somanuals.com. All Manuals Search And Download.
25
BEAM
Beam allows you to switch the frequency of your sonar beam. The Beam
function allows you to eliminate cross-talk interference from neighboring
fishfinders or to simply choose the type of beam that suits your fishing needs.
Selecting 240 kHz will provide a wider beam with more coverage but less detail, while
selecting 455 kHz will provide a narrower beam with more resolution.
NOTE: Your other option is to use the Noise key to reduce cross-talk interference (see
Noise Rejection for more information).
1. Press the Beam key to toggle between 240 kHz and 455 kHz.
Wide Beam (240 kHz)
Wide Beam (240 kHz)
ICE 35
ICE 45/55
The active frequency is displayed
as a narrow or wide blue line
at the top of the Flasher Dial.
(455 kHz or 240 kHz, where Narrow
= 455 kHz, and Wide = 240 kHz;
Default = Wide)
The active frequency is shown as
a narrow or wide beam on the Active
Display. (455 kHz or 240 kHz, where
Narrow beam = 455 kHz, and Wide
beam = 240 kHz; Default = Wide)
Download from Www.Somanuals.com. All Manuals Search And Download.
26
COLOR (ICE 55 Only)
ICE 35 Flasher and ICE 45 Flasher use Color Palette 1 to display sonar
returns on the Flasher Dial. The Color Key, available in the ICE 55 Flasher
only, allows you to choose between three color palettes so that you can view sonar
return signals in higher detail. (Color Palette 1, 2, or 3; Default = Palette 1)
1. Press the Color key to choose Color Palette 1, 2, or 3.
2. ICE 55 will save the setting and display the palette immediately. Also, the palette
number will be shown on the Active Display.
See Palette 1, Palette 2, or Palette 3 for more information.
Palette 1 (ICE 35/45/55)
Red
Strong Signal
Dense, large objects such as fish, thick
vegetation, or hard bottom, are usually displayed
as thick or thin red lines on the Flasher Dial. In
Palette 1, Red indicates a strong sonar return
signal.
Yellow
Medium Signal
Small objects such as fish, sparse vegetation, or
soft bottom (sand or mud) are usually displayed
as yellow lines on the Flasher Dial. In Palette 1,
Yellow indicates a medium sonar return signal.
Palette Number
NOTE: The location of an object in
relation to the transducer can
influence how it appears on the
Flasher Dial. For example, a large
object might display as a weak
sonar return signal if it is located
on the outer edges of the
transducer beam, where as a
small object located at the top of
the transducer beam might display
as a strong sonar return signal.
Green
Weak Signal
Light objects such as your jig, bait fish, sparse
vegetation, and sometimes microscopic activity
or turbulence are displayed as green lines on the
Flasher Dial. In Palette 1, Green indicates a weak
sonar return signal.
Download from Www.Somanuals.com. All Manuals Search And Download.
27
Palette 2 (ICE 55 Only)
If you have a high-end ICE 55 Flasher, you will
also have the choice of Palette 2 to display your
sonar data.
Red
Strong Signal
Dense, large objects such as fish, thick
vegetation, or hard bottom, are usually displayed
as thick or thin red lines on the Flasher Dial. In
Palette 2, Red indicates a strong sonar return
signal.
Palette Number
Green
Medium Signal
Small objects such as fish, sparse vegetation, or
soft bottom (sand or mud) are usually displayed
as green lines on the Flasher Dial. In Palette 2,
Green indicates a medium sonar return signal.
NOTE: The location of an object in
relation to the transducer can
influence how it appears on the
Flasher Dial. For example, a large
object might display as a weak
sonar return signal if it is located
on the outer edges of the
transducer beam, where as a
small object located at the top of
the transducer beam might display
as a strong sonar return signal.
Yellow
Weak Signal
Light objects such as your jig, bait fish, sparse
vegetation, and sometimes microscopic activity
or turbulence are displayed as yellow lines on the
Flasher Dial. In Palette 2, Yellow indicates a weak
sonar return signal.
Download from Www.Somanuals.com. All Manuals Search And Download.
28
Palette 3 (ICE 55 Only)
If you have a high-end ICE 55 Flasher, you will
also have the choice of Color Palette 3, which is
a 6-color palette.
Red
Strong Signal
Dense, large objects such as fish, thick
vegetation, or hard bottom, are usually displayed
as thick or thin red lines on the Flasher Dial. In
Palette 3, Red indicates a strong sonar return
signal.
Palette Number
Orange
Fairly Strong Signal
Indicates a sonar return signal with an intensity
in between Red and Yellow.
NOTE: The location of an object in
relation to the transducer can
influence how it appears on the
Flasher Dial. For example, a large
object might display as a weak
sonar return signal if it is located
on the outer edges of the
transducer beam, where as a
small object located at the top of
the transducer beam might display
as a strong sonar return signal.
Yellow
Medium Signal
Small objects such as fish, sparse vegetation, or
soft bottom (sand or mud) are usually displayed
as yellow lines on the Flasher Dial. In Palette 3,
Yellow indicates a medium sonar return signal.
Light Green
Fairly Weak Signal
Indicates a sonar return signal with an intensity
in between Yellow and Green.
Green
Weak Signal
Light objects and softer bottoms such as your jig,
bait fish, sparse vegetation, are displayed as
green lines on the Flasher Dial. In Palette 3, Green
indicates a weak sonar return signal.
Blue
Very Weak Signal
Indicates a sonar return signal with an intensity
less than Green.
Download from Www.Somanuals.com. All Manuals Search And Download.
29
TARGET (ICE 55 Only)
When you activate the Target key, the ICE 55 Flasher displays the
depth reading of a particular point of the Flasher Dial that you choose.
(Default = Off)
1. Press the Target key. A purple line will display in the Flasher Dial.
Target Symbol on the Active
Display Showing Active
Target Mode
Target Line
(Purple)
Depth Reading of
Target Line on the Dial
2. Turn the Selection dial and position the purple Target line to the depth you
want to read. The depth reading of the target line location will be shown on
the Active Display.
NOTE: When the Target function is active, it replaces the bottom depth reading on the
Active Display. To exit the Target depth reading, press the Target key.
Download from Www.Somanuals.com. All Manuals Search And Download.
30
DUAL MODE KEY FUNCTIONS
There are several additional functions that you may use by holding and pressing certain
keys. Additional features include:
Backlight: Press and hold the Gain key to turn on and off the backlight for night fishing
and to save battery power - ICE 45 and 55 only. (On, Off; Default = Off)
Units: Press and hold the Noise key in order to change the units of measure from feet
to meters or back again - ICE 45 and 55 only. (feet, meters; Default = feet)
Battery: Press and hold the Beam key in order to see the percentage of power left on
the battery.
The battery status will display on the Flasher Dial for approximately 5 seconds, and then
the Flasher Dial will resume Normal operation.
Voltage Will Flash When
the Battery is Empty
%
Battery Gauge
Percentage of
Battery Power
Empty
Green Line Indicating
Percentage of Battery Power
ICE 35
ICE 45/55
The percentage of battery power is
indicated on the battery gauge,
which is located on the bottom of
the Range Scale. A green line will
be displayed between E and F to
indicate the percentage on the
battery gauge. When the battery is
empty, the line will turn red. (On,
Off, Default = Off)
The percentage of battery power is
shown on the Active Display. When
the battery is empty, the Voltage icon
will flash. (On, Off, Default = Off)
Download from Www.Somanuals.com. All Manuals Search And Download.
31
MAINTENANCE
To keep both your ICE Flasher Series™ control head and your transducer working
properly, perform the following maintenance tasks as needed.
ICE FLASHER SERIES™ MAINTENANCE
If your ICE Flasher Series™ unit comes into contact with salt spray, simply wipe the
affected surfaces with a cloth dampened in fresh water. Do not use a chemical glass
cleaner on the lens, as chemicals in the solution may cause cracking in the lens. When
cleaning the LCD protective lens, use a chamois and non-abrasive, mild cleaner. Do not
wipe while dirt or grease is on the lens. Be careful to avoid scratching the lens.
WARNING: Never leave your ICE Flasher Series™ Fishfinder in a closed car or trunk; the
extremely high temperatures generated in hot weather can damage the electronics.
TRANSDUCER MAINTENANCE
If your transducer remains out of the water for a long period of time, it may take some
time to wet the transducer after it is returned to the water. Small air bubbles can cling
to the surface of the transducer and interfere with proper operation. These bubbles will
dissipate with time, or you may wipe the face of the transducer with your fingers after
the transducer is in the water.
Download from Www.Somanuals.com. All Manuals Search And Download.
32
TROUBLESHOOTING
Before contacting the Humminbird® Customer Resource Center, please read the
following section. Taking the time to review these troubleshooting guidelines may allow
you to solve a performance problem yourself, and therefore avoid sending your unit back
for repair.
NOTE: Do not attempt to repair the unit yourself, as there are no user serviceable parts
inside, and special tools and techniques are required for reassembly in order to maintain
the waterproof integrity of the housing. Repairs should be performed only by authorized
Humminbird® technicians.
ICE Flasher Series™ Fishfinder Doesn’t Power Up
If your ICE Flasher Series™ control head doesn’t power up, refer to the Installation
section, and make sure that:
• the power cable is properly connected to the ICE Flasher Series™ Fishfinder;
• the power cable is wired correctly, with red to positive battery terminal and black
to negative terminal or ground;
• the battery voltage of the power connector is between 10.5 and 20 VDC.
Correct any known problems, including removing corrosion from the battery terminals
or wiring, or actually replacing the battery if necessary.
No Bottom Reading on the Display
If there is no bottom reading visible on the display, there are a number of possible
causes for this condition, including:
• check the transducer cable connection on the back of the ICE Flasher Series™
control head and make sure that the cable to the transducer has not been cut or
pinched, as even a small abrasion in the cable can affect performance significantly.
No Continuous Depth Display in Very Shallow Water
Losing continuous depth when the transducer is in very shallow water is normal,
because the automatic range control cannot lock onto the bottom in depths of one foot
or less.
Screen Fades, Images Are Not Sharp
If the screen begins to fade, and images are not as sharp as normal, check the input
voltage. The ICE Flasher Series™ will not operate on input voltages below 10.5 VDC.
Download from Www.Somanuals.com. All Manuals Search And Download.
33
2-YEAR LIMITED WARRANTY
We warrant the original retail purchaser that products made by Humminbird® have been
manufactured free from defects in materials and workmanship. This warranty is
effective for two years from the date of original retail purchase. Humminbird® products
found to be defective and covered by this warranty will be replaced or repaired free of
charge at Humminbird’s option and returned to the customer freight prepaid.
Humminbird’s sole responsibility under this warranty is limited to the repair or
replacement of a product that has been deemed defective by Humminbird®.
Humminbird® is not responsible for charges connected with the removal of such product
or reinstallation of replaced or repaired parts.
This warranty does not apply to a product that has been:
• Improperly installed;
• Used in an installation other than that recommended in the product installation
and operation instructions;
• Damaged or has failed because of an accident or abnormal operation;
• Repaired or modified by entities other than Humminbird®.
Please retain your original receipt as a proof of the purchase date. This will be required
for in-warranty service.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER WARRANTIES, OBLIGATIONS
OR LIABILITIES ON THE PART OF HUMMINBIRD® AND WILL BE THE CUSTOMER'S
EXCLUSIVE REMEDY, EXCEPT FOR ANY APPLICABLE IMPLIED WARRANTIES UNDER
STATE LAW WHICH ARE HEREBY LIMITED IN DURATION TO TWO YEARS FROM THE
DATE OF ORIGINAL PURCHASE. IN NO EVENT WILL HUMMINBIRD® BE LIABLE FOR
ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR
IMPLIED WARRANTY RELATING TO THE PRODUCTS.
Some states do not allow limitations on an implied warranty, or the exclusion of
incidental or consequential damages, so the above exclusions may not apply to you. You
may also have other rights, which vary from state to state.
Download from Www.Somanuals.com. All Manuals Search And Download.
34
HUMMINBIRD® SERVICE POLICY
Even though you’ll probably never need to take advantage of our incredible service
policy, it’s good to know that we back our products this confidently. We do it because
you deserve the best. We will make every effort to repair your unit within three business
days from the receipt of your unit at our factory. This does not include shipping time to
and from our factory. Units received on Friday are typically shipped by the following
Wednesday, units received Monday are typically shipped by Thursday, etc.
All repair work is performed by factory-trained technicians to meet exacting factory
specifications. Factory-serviced units go through the same rigorous testing and quality
control inspections as new production units.
After the original warranty period, a standard flat rate service charge will be assessed
for each repair (physical damage and missing parts are not included). Any repairs made
after the original warranty will be warranted for an additional 90 days after service has
been performed by our factory technicians. You can contact our Customer Resource
Center or visit our website to verify the flat rate repair fee for your product (visit the
Product Support section):
We reserve the right to deem any product unserviceable when replacement parts are
no longer available or impossible to obtain. This Service Policy is valid in the United
States only. This applies only to Humminbird® products returned to our factory in
Eufaula, Alabama. This Service Policy is subject to change without notice.
DOMESTIC (USA) CUSTOMERS:
PLEASE DO NOT RETURN THIS PRODUCT TO STORE FOR SERVICE
For all technical issues please call 1-800-633-1468
Please reference product serial number and
model number when contacting Humminbird®.
Download from Www.Somanuals.com. All Manuals Search And Download.
35
Returning Your Unit for Service
Before sending your unit in for repair, please contact the factory, either by phone or by
email, to obtain a Repair Authorization Number for your unit.
NOTE: Please do not return your Humminbird® product to the store for service.
Please have your product model name and serial number available before calling the
factory. If you contact the factory by e-mail, please include your product model name
and serial number in the e-mail, and use Request for Repair Authorization Number for
your e-mail subject header. You should include your Repair Authorization Number in all
subsequent communications about your unit.
For IN-WARRANTY service, complete the following steps:
• Obtain a Repair Authorization Number from the Humminbird® Customer Resource
Center.
• Tag product with your name, street address, phone number and your assigned
Repair Authorization Number.
• Include a brief written description of the problem.
• Include a copy of your receipt (to show proof and date of purchase).
• Return product freight prepaid to Humminbird®, using an insured carrier with
delivery confirmation.
For OUT-OF-WARRANTY service, complete the following steps:
• Obtain a Repair Authorization Number from the Humminbird® Customer Resource
Center.
• Include payment in the form of credit card number and expiration date, money
order or personal check. Please do not send cash.
• Tag product with your name, street address, phone number and your assigned
Repair Authorization Number.
• Include a brief written description of the problem.
• Return product freight prepaid to Humminbird®, using an insured carrier with
delivery confirmation.
Download from Www.Somanuals.com. All Manuals Search And Download.
36
SPECIFICATIONS
Depth Capability ................................................................................................ 200 ft (60 m)
Power Cable Length .............................................................................................. 11", 28cm
Operating Frequency ................................................................................ 240 kHz / 455 kHz
Flasher Dial Resolution ....................................................................................................526
Number of Colors................................................................................................ICE 35/45: 3
ICE 55: 6
Area of Coverage .............................................................................. 240 kHz: 19° @ -3 dB
455 kHz: 9° @ -3 dB
Power Requirement............................................................................................10.5-20 VDC
Power Output (RMS)...................................................................................... ICE 35: 100 W
ICE 45: 225 W
ICE 55: 300 W
Power Output (Peak to Peak) ........................................................................ ICE 35: 800 W
ICE 45: 1800 W
ICE 55: 2400 W
Display ...................................................................... ICE 45/55: Liquid Crystal Diode (LCD)
Unit Housing .......................................................................................... High-Impact Plastic
Transducer .................................................................................................................. XI 9 19
Transducer Cable Length...................................................................................... 8 ft (2.4m)
NOTE: Humminbird® verifies maximum stated depth in saltwater conditions, but actual
depth performance may vary due to transducer installation, water type, thermal layers,
bottom composition and slope.
NOTE: Product specifications and features are subject to change without notice.
ENVIRONMENTAL COMPLIANCE STATEMENT: It is the intention of Humminbird® to be a
responsible corporate citizen, operating in compliance with known and applicable
environmental regulations, and a good neighbor in the communities where we make or sell
our products.
Download from Www.Somanuals.com. All Manuals Search And Download.
37
WEEE DIRECTIVE: EU Directive 2002/96/EC “Waste of Electrical and Electronic Equipment
Directive (WEEE)” impacts most distributors, sellers, and manufacturers of consumer
electronics in the European Union. The WEEE Directive requires the producer of consumer
electronics to take responsibility for the management of waste from their products to achieve
environmentally responsible disposal during the product life cycle.
WEEE compliance may not be required in your location for electrical & electronic equipment
(EEE), nor may it be required for EEE designed and intended as fixed or temporary installation
in transportation vehicles such as automobiles, aircraft, and boats. In some European Union
member states, these vehicles are considered outside of the scope of the Directive, and EEE
for those applications can be considered excluded from the WEEE Directive requirement.
This symbol (WEEE wheelie bin) on product indicates the product must not be
disposed of with other household refuse. It must be disposed of and collected for
recycling and recovery of waste EEE. Humminbird® will mark all EEE products in
accordance with the WEEE Directive. It is our goal to comply in the collection,
treatment, recovery, and environmentally sound disposal of those products; however, these
requirement do vary within European Union member states. For more information about
where you should dispose of your waste equipment for recycling and recovery and/or your
European Union member state requirements, please contact your dealer or distributor from
which your product was purchased.
ROHS STATEMENT: Product designed and intended as a fixed installation or part of a
system in a vessel may be considered beyond the scope of Directive 2002/95/EC of the
European Parliament and of the Council of 27 January 2003 on the restriction of the use of
certain hazardous substances in electrical and electronic equipment.
Download from Www.Somanuals.com. All Manuals Search And Download.
38
NOTES
Download from Www.Somanuals.com. All Manuals Search And Download.
39
Contact Humminbird®
Contact the Humminbird® Customer Resource Center
in any of the following ways:
By Telephone
(Monday - Friday 8:00 a.m. to 4:30 p.m. Central Standard Time):
1-800-633-1468
By e-mail
(typically we respond to your e-mail within three business days):
For direct shipping, our address is:
Humminbird
Service Department
678 Humminbird Lane
Eufaula, AL 36027 USA
Download from Www.Somanuals.com. All Manuals Search And Download.
40
|