NOTE:
Please read all
instructions carefully
before using this product
WEIGHT BENCH
Table of Contents
Safety Notice
MSS-7500
Hardware Pack
Assembly Instruction
Exploded Diagram
Parts List
Warranty
Ordering Parts
Model
MSS-7500
Retain This
Manual for
Reference
06/11/09
IMPEX® INC.
14777 Don Julian Rd., City of Industry, CA 91746
Tel: (800) 999-8899 Fax (626) 961-9966
OWNER'S
MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT leave children
unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms,
STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine near water or
outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear robes or other
clothing that could become caught in the machine. Running or aerobic shoes are also
required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO NOT use
attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or physician in
attendance.
10. Before using the machine to exercise, always do stretching exercises to properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
13. This machine is designed and intended for home and consumer use only, not for
commercial use.
14. Maximum user’s weight: 300 lbs.
15. Maximum weight on uprights: 600 lbs.
16. Maximum weight on leg developer: 100 lbs.
CARE AND MAINTENANCE
1. Inspect and tighten all parts before using the machine.
2. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT
YOUR PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS
OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH
PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS
EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL
INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE
OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING LABEL PLACEMENT
The Warning Labels shown here have been placed on the Cross Brace. If the label is
missing or illegible, please call customer service at 1-800-999-8899 for replacement.
Apply the label in location shown
3
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
4
HARDWARE PACK
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTION
Tools Required For Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches. NOTE: It is strongly recommended for two or more people to assemble this
machine to avoid possible injury.
STEP 1
(See Diagram 1)
A.) Do not tighten the Nuts and Bolts until instructed to do so.
B.) Connect the two Upright Beams (#1) by a Cross Brace (#2) in the mid-span. Secure
each end of the Cross Brace to Upright Beam with two M10 x 3 ¾” Carriage Bolts (#30),
one 5 ½” Curved Bracket (#13), two Ø ¾” Washers (#36), and two M10 Aircraft Nuts
(#38).
C.) Insert two Crutches (#7) into the openings on the two Upright Beams. Thread a M18
Lock Knob (#16) into the Upright Beam to lock each Crutch at desired height.
D.) Place the Backrest Adjustment Bar (#8) onto the selected peg to obtain the backrest
incline.
DIAGRAM 1
6
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Attach the Main Seat Support (#3) to the Front Post (#4). Secure it with two M10 x 2 3/8”
Carriage Bolts (#32), one 6 ¼” x 3 ¼” Bracket (#14), two Ø ¾” Washers (#36), and two
M10 Aircraft Nuts (#38).
B.) Attach the Main Seat Support to the Cross Brace (#2). Secure it with two M10 x 2 ½”
Carriage Bolts (#31), one 5 ½” x 3” Curved Bracket (#15), two Ø ¾” Washer (#36), and
two M10 Aircraft Nut (#38).
C.) Securely tighten all Nuts and Bolts in Step-1 and Step-2.
DIAGRAM 2
7
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3
(See Diagram 3)
A.) Attach the Seat Bracket (#5) to the pivot on the Main Seat Support (#3). Attach the holes
on the end of the two Backrest Supports (#6) to the Seat Bracket. Align the holes. Secure
the two Backrest Supports, Seat Bracket together to the pivot with one M12 x 7” Hex Bolt
(#26), two Ø 1” Washers (#37), and one M12 Aircraft Nut (#39). Do not over tighten the
Nuts and Bolts. Make sure the Backrest Supports are able to swivel.
B.) Attach the Backrest Board (#11) to the Backrest Supports. Secure it with four M8 x 1 5/8”
Allen Bolts (#34) and four Ø 5/8” Washers (#35).
C.) Place the Seat Pad onto the Seat Bracket. Secure it with four M8 x 1 5/8” Allen Bolts (#34)
and four Ø 5/8” Washers (#35).
DIAGRAM 3
8
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4
(See Diagram 4)
A.) Attach the Leg Developer (#9) to the open bracket on Main Seat Support (#3). Secure it
with one Leg Developer Axle (#21), two M10 x ¾” Allen Bolt (#33), and two Ø ¾” Washers
(#36). Do not over tighten the Bolts. Make sure the Leg Developer is able to swivel.
B.) Insert two Foam Tubes (#10) halfway through the holes on the Leg Developer. Push four
Foam Rolls (#19) onto the Tubes from both ends. Plug four Foam Roll End Caps (#26)
into the ends.
C.) Slide an Olympic Sleeve (#24) onto the weight post on Leg Developer. Attach a Spring
Clip (#20) onto the Sleeve.
DIAGRAM 4
9
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY NO.
DESCRIPTION
QUANTITY
1
2
3
4
5
6
7
8
Upright Beam
Cross Brace
Main Seat Support
Front Post
Seat Bracket
Backrest Support
Crutch
Backrest Adjustment Bar
Leg Developer
Foam Tube
Backrest Board
Seat Pad
5 ½” Curved Bracket
6 ¼” x 3 ¼” Bracket
5 ½” x 3” Curved Bracket
M18 Lock Knob
Sleeve
Rubber Cover
Foam Roll
Spring Clip
Leg Developer Axle
Plastic Bushing
Rubber Bumper
Olympic Sleeve
Ø 2” End Cap
Foam Roll End Cap
1” Square End Cap
Ø 1” End Cap
M12 x 7” Hex Bolt
M10 x 3 ¾” Carriage Bolt
M10 x 2 ½” Carriage Bolt
M10 x 2 3/8” Carriage Bolt
M10 x ¾” Allen Bolt
M8 x 1 5/8” Allen Bolt
Ø 5/8” Washer
2
1
1
1
1
2
2
1
1
2
1
1
2
1
1
2
2
6
4
1
1
2
1
1
2
4
2
2
1
4
4
2
2
8
8
12
2
10
1
1
1
2
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
Ø ¾” Washer
Ø 1” Washer
M10 Aircraft Nut
M12 Aircraft Nut
#4 Allen Wrench (Tool)
#5 Allen Wrench (Tool)
#6 Allen Wrench (Tool)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPEX INC.
LIMITED WARRANTY
®
IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal
use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty
extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing,
at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Customer
Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be prepaid by the
customer. This warranty does not extend to any product or damage to a product caused by or attributable to
freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an IMPEX authorized
service center or for products used for commercial or rental purposes. No other warranty beyond that specifically
set forth above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in connection
with the use or performance of the product or other damages with respect to any economic loss, loss of property,
loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other consequential
damages or whatsoever natures.
Some states do not allow the exclusion or limitation of incidental or
consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein.
Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation may
not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state to state.
®
IMPEX INC.
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-999-8899 during
our regular business hours: Monday through Friday, 9 am until 5 pm Pacific standard time.
When ordering replacement parts, always give the following information.
1.
2.
3.
4.
Model
Description of Parts
Part Number
Date of Purchase
12
Download from Www.Somanuals.com. All Manuals Search And Download.
|