Impex Home Gym CR 5 User Manual

NOTE:  
Please read all instructions  
carefully before using this  
product  
Table of Contents  
Safety Notice  
MARCY CORNER GYM  
CR 5  
Hardware Identifier  
Assembly Instruction  
Parts List  
Resistance Chart  
Warranty  
Ordering Parts  
Model  
MWB CR 5  
Retain This  
Manual for  
Reference  
9-20-02  
OWNER'S  
MANUAL  
IMPEX FITNESS PRODUCTS  
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746  
Tel: (800) 999-8899 Fax: (626) 961-9966  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT SAFETY NOTICE  
PRECAUTIONS  
This exercise machine is built for optimum safety. However, certain precautions apply whenever  
you operate a piece of exercise equipment. Be sure to read the entire manual before you  
assemble or operate your machine. In particular, note the following safety precautions:  
1. Keep children and pets away from the machine at all times. DO NOT  
leave children unattended in the same room with the machine.  
2. Only one person at a time should use the machine.  
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal  
symptoms, STOP the workout at once. CONSULT A PHYSICIAN  
IMMEDIATELY.  
4. Position the machine on a clear, leveled surface. DO NOT use the machine  
near water or outdoors.  
5. Keep hands away from all moving parts.  
6. Always wear appropriate workout clothing when exercising. DO NOT wear  
robes or other clothing that could become caught in the machine. Running  
or aerobic shoes are also required when using the machine.  
7. Use the machine only for its intended use as described in this manual. DO  
NOT use attachments not recommended by the manufacturer.  
8. Do not place any sharp object around the machine.  
9. Disabled person should not use the machine without a qualified person or  
physician in attendance.  
10. Before using the machine to exercise, always do stretching exercises to  
properly warm up.  
11. Never operate the machine if the machine is not functioning properly.  
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR PHYSICIAN.  
THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS  
WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING  
ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL  
INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS  
PRODUCT.  
SAVE THESE INSTRUCTIONS.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY INSTRUCTION  
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches  
NOTE: It is strongly recommended two or people assembling this machine to avoid  
possible injury.  
STEP 1 (See Diagram 1)  
A.) Place the Right Base Frame (#46) and Left Base Frame (#87) on the floor, at a right angle to  
each other. Attach the Rear Vertical Beam (#50) to the joint and align the holes. Secure the  
holes with two M10 x 3” Carriage Bolts (#64), 3/4” Washers (#6) and M10 Aircraft Nuts (#5).  
DO NOT tighten all the nuts and bolts yet.  
Diagram 1  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 2 (See Diagram 2)  
A.) Attach the Right Vertical Beam (#21) to the Right Base Frame (#46). Secure it with two M10 x  
2 ¾” Carriage Bolts (#17), ¾” Washers (#6), and M10 Aircraft Nuts (#5).  
B.) Attach the Right Seat Support (#49) to the Right Vertical Beam (#21). Secure it with one  
Bracket (#7), two M10 x 2 ¾” Carriage Bolts (#17), ¾” Washers (#6), and M10 Aircraft Nuts  
(#5).  
C.) Attach the other end of Right Seat Support (#49) to the Right Base Frame (#46). Secure it with  
one M10 x 2 ¾” Carriage Bolt (#17), ¾” Washer (#6), and M10 Aircraft Nut (#5).  
D.) Attach the Leg Developer (#40) to the front open bracket on the Right Seat Support. Secure it  
with a Leg Developer Axle (#41), two ¾” Washers (#6), and M10 x ¾” Allen Bolts (#37).  
DIAGRAM 2  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 3 (See Diagram 3)  
A.) Slide two 2 ½” Rubber Bumpers (#58) onto two Chromed Guide Rods (#58). Insert the two  
Guide Rods into the holes on the Right Base Frame (#46). Slide the Selector Stem (#67) onto  
the two Guide Rods (#22). Slide the Selector Stem over the Selector Rod (#69). Secure the  
Selector Rod to the Selector Stem with two M10 x 1” Allen Bolts (#56). DO NOT install the  
plates yet.  
B.) Repeat the Procedure A above to install another set of Guide Rods.  
C.) Place the Upper Frame (#8) over the two sets of Guide Rods then onto top of Right Vertical  
Beam (#21) and Rear Vertical Beam (#50).  
D.) Secure each set of Guide Rods (#22) to the Upper Frame with two M10 x 1” Allen Bolts (#56)  
and ¾” Washers (#6).  
E.) Secure the Right Vertical Beam (#21) to the Upper Frame with one Bracket (#7), two M10 x 2  
¾” Carriage Bolts (#17), ¾” Washers (#6), and M10 Aircraft Nuts (#5).  
F.) Attach top of Left Vertical Beam (#77) to the Upper Frame. Attach the bottom of Left Vertical  
Beam to the Left Base Frame (#87). Secure the bottom of Left Vertical Beam with two M10 x 2  
¾” Carriage Bolts (#17), ¾” Washers (#6), and M10 Aircraft Nuts (#5).  
G.)Secure the Left Vertical Beam (#77), Rear Vertical Beam (#50), and Upper Frame (#8) all  
together with two M10 x 3” Carriage Bolts (#64), ¾” Washers (#6), and M10 Aircraft Nuts  
(#5).  
H.) Attach the Left Seat Support (#92) to the Left Vertical Beam (#77). Secure it with one Bracket  
(#7), two M10 x 2 ¾” Carriage Bolts (#17), ¾” Washers (#6), and M10 Aircraft Nuts (#5).  
Attach the other end of Left Seat Support (#92) to the Left Base Frame (#87). Secure it with  
one M10 x 2 ¾” Carriage Bolt (#17), ¾” Washer (#6), and M10 Aircraft Nut (#5).  
I.) Securely tighten all nuts and bolts previously installed.  
J.) Carefully tilt the machine on its side. (Help of another person is a MUST.) Secure the four  
Guide Rods (#22) to the Right Base Frame (#46) with four M10 x 1” Allen Bolts (#56).  
K.) Attach the bottom of Leg Press Frame (#84) to the bracket on the Left Base Frame (#87).  
Secure it with a M12 x 3” Allen Bolt (#89), two 7/8” Washers (#71), and one M12 Aircraft Nut  
(#57).  
L.) Attach a Leg Press Diagonal Support (#90) to each side of the Leg Press Frame. Secure them  
together with two M10 x 2 ½” Carriage Bolts (#100), ¾” Washers (#6), and M10 Aircraft Nuts  
(#5).  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
DIAGRAM 3  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 4 (See Diagram 4)  
A.) Attach the Front Press Base (#97) to the Right Base Frame (#46). Secure it with a 9 ¼” Front  
Press Axle (#60), two ¾” Washers (#6), and two M10 Aircraft Nuts (#5).  
B.) Attach the Front Press Frames (#63) to the Front Press Base. Secure it with four M10 x 2 ¾”  
Carriage Bolts (#17), ¾” Washers (#6), and M10 Aircraft Nuts (#5).  
DIAGRAM 4  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 5 (See Diagram 5)  
A.) Attach the Butterfly Support Frame (#18) to the front of Right Vertical Beam (#21). Attach the  
Butter Pulley Support (#74) to the back of Right Vertical Beam. Align the holes. Secure them  
together with two M10 x 2 ¾” Carriage Bolts (#17), ¾” Washers (#6), and M10 Aircraft Nuts  
(#5).  
B.) Insert the Axle on the Left Butterfly (#20) into the hole on the Butterfly Support Frame from the  
bottom. Secure it with one 1 ½” Washer (#16), 1 3/8” Lock Ring (#13), M6 x 1 5/8” Hex  
Bolt (#12), and M6 Aircraft Nut (#14). Repeat the same procedure to install the other side.  
C.) Slide two Butterfly Foam Rolls (#27) onto the Butterfly Arms.  
D.) Attach a Swivel Pulley Bracket (#72) to the bottom of the Butterfly Pulley Support (#74).  
Secure it with a M12 x 4 ½” Allen Bolt (#70), two 7/8” Washers (#71), and one M12 Aircraft Nut  
(#57). Repeat for the other side.  
DIAGRAM 5  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 6 (See Diagram 6)  
A.) Attach the Vertical Press Frame (#78) to the Rear Vertical Beam (#50). Secure it with a M10 x  
4 7/8” Vertical Press Axle (#81), two ¾” Washers (#6), and two M10 x 1” Allen Bolts (#56).  
B.) Place the Vertical Press Frame rest onto the 1 ½” Rubber Bumper (#83).  
DIAGRAM 6  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CABLE LOOP DIAGRAM  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 7 (Upper Cable Loop & Diagram 7)  
A.) Attach the 108” Upper Cable (#93) to the front opening on the Upper Frame (#8). Attach a  
Pulley (#79) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#10), two Pulley  
Bushings (#11), and one M10 Aircraft Nut (#5). Draw the Cable towards the back of the  
machine. Note: Make sure the Ball Stopper is underneath the frame.  
B.) Attach a Pulley to the bracket on the Upper Frame. Secure it with one M10 x 2” Allen Bolt  
(#98), two ¾” Washers (#6), one L-shaped Pulley Bracket (#86), and one M10 Aircraft Nut  
(#5).  
C.) Pull the Cable downward. Install a Pulley with a Flat Double Floating Pulley Bracket (#59). Let  
the bracket hanging for now.  
D.) Draw the Cable around the Pulley then upward to the second open bracket on the Upper  
Frame. Install another Pulley with a U-shaped Pulley Bracket (#85).  
E.) Draw the Cable around the Pulley then downward to the Selector Rod (#69). Securely thread  
the end of the Cable into the Selector Rod (#69).  
UPPER CABLE LOOP DIAGRAM  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DIAGRAM 7  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 8 (See Butterfly Cable Loop & Diagram 8)  
A.) Attach the 83” Butterfly Cable (#95) to the slot on the back of Left Butterfly (#20). Draw the  
Cable through the slot then to the open left Swivel Pulley Bracket (#72).  
B.) Attach a Pulley (#79) to the bracket. Secure it with one M10 x 2” Allen Bolt (#98), two ¾”  
Washers (#6), and one M10 Aircraft Nut (#5).  
C.) Draw the Cable around the Pulley then downward. Install a Pulley to the Angled Double  
Floating Bracket (#51). Let the Bracket hanging for now.  
D.) Draw the Cable upward to the right Swivel Pulley Bracket. Install another Pulley..  
E.) Draw the Cable to the Right Butterfly (#26) and secure the cable end to the slot.  
BUTTERFLY CABLE LOOP DIAGRAM  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DIAGRAM 8  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 9 (See Front Press Cable Loop & Diagram 9)  
A.) Attach the 247” Front Press Cable (#94) to the lower opening on the Leg Developer (#40).  
B.) Attach a Pulley (#79) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#10), two  
Pulley Bushings (#11), and one M10 Aircraft Nut (#5).  
C.) Draw the Cable underneath the Pulley through the opening on the Right Seat Support (#49) to  
the open bracket on the Right Base Frame (#46).  
D.) Attach a Pulley to the bracket. Secure it with one M10 x 2” Allen Bolt (#98), two ¾” Washers  
(#6), and one M10 Aircraft Nut (#5).  
E.) Continue drawing the Cable along the Right Base Frame to another open bracket. Install a  
Pulley as described in Step D above with a L-shaped Pulley Bracket (#86). Draw the Cable  
around the Pulley then back to the opening between the Front Press Base (#97).  
F.) Attach a Pulley to the opening. Secure it with one M10 x 8 ¼” Allen Bolt (#62), two ¾”  
Washers (#6), and one M10 Aircraft Nut (#5).  
G.) Draw the Cable around the Pulley then back to the lower opening on the Right Vertical Beam  
(#21). Install another Pulley as described in Step D above. Draw the Cable back to the open  
bracket on the back of Front Press Base.  
H.) Install another Pulley as described in Step D above. Draw the Cable back through the lower  
opening on the Right Vertical Beam (#21) to the open bracket on the back of the Beam. Install  
another Pulley.  
I.) Draw the Cable upward to the hanging Angled Double Floating Bracket (#51) previously  
installed in STEP 8. Install another Pulley. Draw the Cable downward to the open bracket on  
the Right Base Frame (#46). Install another Pulley with a U-shaped Pulley Bracket (#85).  
J.) Draw the Cable upward to the hanging Flat Double Floating Pulley Bracket (#59) previously  
installed in STEP 7. Install another Pulley.  
K.) Draw the Cable around the Pulley then downward and connect to the Right Base Frame with a  
Chain (#3) and two C-clips (#4). Adjust the tension of the Cable by adjusting the length of the  
Chain.  
FRONT PRESS CABLE LOOP DIAGRAM  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DIAGRAM 9  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 10 (See Leg Press Cable Loop & Diagram 10)  
A.) Attach one end of the 82” Leg Press Cable (#96) to the open slot on the back of the Leg  
Press Frame (#84). Secure it with one M10 x 2 ½” Allen Bolt (#10), two ¾” Washers (#6),  
and one M10 Aircraft Nut (#5).  
B.) Draw the Cable to the front opening on the Left Seat Support (#92). Attach a Pulley to the  
opening. Secure it with one M10 x 2 ½” Allen Bolt (#10), two Pulley Bushings (#11), and one  
M10 Aircraft Nut (#6).  
C.) Draw the Cable around the Pulley then back to the lower opening on the Leg Press Frame.  
Install a Pulley as described in Step B above.  
D.) Draw the Cable around the Pulley then towards back of the machine through the hole on the  
bottom of the Left Vertical Beam (#77) to the open bracket on the Left Base Frame (#87).  
E.) Attach a Pulley to the bracket. Secure it with one M10 x 2” Allen Bolt (#98), two ¾”  
Washers (#6), one L-shaped Pulley Bracket (#86), and one M10 Aircraft Nut (#5).  
F.) Pull the Cable upward and connect to the 298” Vertical Press Cable (#102) with two C-clips  
(#4) and one Chain (#3). After completing the steps, adjust the length of this Chain to adjust  
the tightness of the Cables.  
G.) Draw the Vertical Press Cable to the opening between the Vertical Press Frame (#78). Attach  
a Pulley to the opening. Secure it with one M10 x 5 ¾” Allen Bolt (#82), two ¾” Washers  
(#6), and one M10 Aircraft Nut (#5).  
H.) Draw the Cable around the Pulley and downward to the middle open bracket on the Left Base  
Frame. Install a Pulley with a U-shaped Pulley Bracket (#85).  
I.) Pull the Cable upward back to the opening on the Vertical Press Frame. Install another Pulley  
as described in Step G above.  
J.) Draw the Cable downward to the last open bracket on the rear of the Left Base Frame. Install  
a Pulley with a U-shaped Pulley Bracket (#85).  
K.) Draw the Cable upward to the last open bracket on the Upper Frame (#8). Install another  
Pulley. Draw the Cable downward and securely threaded it into the Selector Rod.  
LEG PRESS CABLE LOOP DIAGRAM  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DIAGRAM 10  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 11 (See Diagram 11)  
A.) Place a Seat Pad (#29) onto the Left Seat Support (#92). Secure it with two M8 x 2 1/8” Allen  
Bolts (#25) and 5/8” Washers (#24).  
B.) Attach a Backrest Board (#28) to the Left Vertical Beam (#77). Secure it with two M8 x 2 1/8”  
Allen Bolts (#25) and 5/8” Washers (#24).  
C.) Attach the Leg Press Plate (#76) onto the Leg Press Frame (#84). Secure it with a L-shaped  
Pin (#75).  
DIAGRAM 11  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 12 (See Diagram 12)  
A.) Place a Seat Pad (#29) onto the Right Seat Support (#49). Secure it with two M8 x 2 1/8”  
Allen Bolts (#25) and 5/8” Washers (#24).  
B.) Attach a Backrest Board (#28) to the Right Vertical Beam (#21). Secure it with two M8 x 2 1/8”  
Allen Bolts (#25) and 5/8” Washers (#24).  
C.) Insert two Foam Roll Tubes (#36) halfway through the holes on the Right Seat Support (#49)  
and Leg Developer (#40). Push four Foam Rolls (#33) onto the Tubes from both sides. Plug  
four 1” Round End Caps (#32) into the ends.  
D.) Attach the Arm Curl Pad (#34) to the Arm Curl Stand (#35). Secure it with two M8 x 5/8” Allen  
Bolts (#31) and 5/8” Washers (#24). Insert the Arm Curl Stand into the opening in front of  
the seat. Use the Lock Knob (#47) on the Right Seat Support to obtain the desired position.  
E.) Connect the Lat Bar (#2) to the Upper Cable with a C-clip (#4) and a Chain (#3).  
F.) Connect the Arm Curl Handle (#44) to the Front Press Cable (#94) with a C-clip (#4) and a  
Chain (#3).  
DIAGRAM 12  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 13 (See Diagram 13)  
A.) Securely tighten all the nuts and bolts previously installed.  
B.) Before putting the Weight Plates on, now move the machine to the corner of the room or  
place where you will use the machine.  
C.) Lift up the Selector Rod and install one stack of 19 Weight Plates (#66). To install the plates,  
hold the plate at an angle and place between the two Guide Rods then drop it down. Make  
sure the grooves on the plastic covers all face up. All the Plates should interlock with each  
other. See diagram below. It is strongly recommended to spray some lubricant such as WD-  
40 on the two Guide Rods to minimize friction. Use the Selector Pin (#55) to select the desired  
weights. The Magnet on the Pin should face up. Repeat the same procedure to install  
another stack of Weight Plates.  
D.) Attach four Weight Stack Covers (#23) to the machine and secure each Weight Stack Cover  
with two M10 x 1” Allen Bolts (#56) and 3/4” Washers (#6).  
DIAGRAM 13  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PARTS LIST  
51  
52  
53  
54  
55  
56  
57  
58  
59  
60  
61  
62  
63  
64  
65  
66  
67  
68  
69  
70  
71  
72  
73  
74  
75  
76  
77  
78  
79  
80  
81  
82  
83  
84  
85  
86  
87  
88  
89  
90  
91  
92  
93  
94  
95  
96  
97  
98  
99  
Angled Double Floating Bracket  
M5 Screw  
Magnet Box  
Magnet  
Selector Pin  
1
2
2
2
2
22  
3
KEY NO. DESCRIPTION  
Q’ty  
2
1
4
6
52  
82  
3
1
17  
8
10  
2
2
2
2
2
16  
1
2
1
1
4
4
11  
8
1
2
2
2
1
2
4
4
1
1
2
2
1
Lat Bar Grip  
2
Lat Bar  
3
Chain  
4
C-clip  
M10 x 1” Allen Bolt  
M12 Aircraft Nut  
2 ½” Rubber Bumper  
5
M10 Aircraft Nut  
6
7
¾” Washer  
Bracket  
4
Flat Double Floating Pulley Bracket 1  
8
Upper Frame  
9 ¼” Front Press Axle  
7/8” Metal Bushing  
M10 x 8 ¼” Allen Bolt  
Front Press Frame  
M10 x 3” Carriage Bolt  
Weight Plate Cover  
Weight Plate  
Selector Stem  
Selector Stem Bushing  
Selector Rod  
M12 x 4 ½” Allen Bolt  
7/8” Washer  
Swivel Pulley Bracket  
1 ½” Square End Cap  
Butterfly Pulley Support  
L-shaped Pin  
1
14  
1
2
4
76  
38  
2
4
2
2
6
2
3
1
1
1
1
1
25  
2
1
2
1
1
7
2
9
1 ¾” Square End Cap  
M10 x 2 ½” Allen Bolt  
Pulley Bushing  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
47  
48  
49  
50  
M6 x 1 5/8” Hex Bolt  
1 3/8” Lock Ring  
M6 Aircraft Nut  
Butterfly Axle Sleeve  
1 ½” Washer  
M10 x 2 ¾” Carriage Bolt  
Butterfly Support Frame  
2” Square End Cap  
Left Butterfly  
Right Vertical Beam  
Guide Rod  
Weight Stack Cover  
5/8” Washer  
M8 x 2 1/8” Allen Bolt  
Right Butterfly  
Leg Press Plate  
Left Vertical Beam  
Vertical Press Frame  
Pulley  
Butterfly Foam Roll  
Backrest Board  
Seat Pad  
2” x 1” End Cap  
M10 x 4 7/8” Vertical Press Axle  
M10 x 5 ¾” Allen Bolt  
1 ½” Rubber Bumper  
Leg Press Frame  
U-shaped Pulley Bracket  
L-shaped Pulley Bracket  
Left Base Frame  
2” Sleeve  
M8 x 5/8” Allen Bolt  
1” Round End Cap  
Foam Roll  
Arm Curl Pad  
Arm Curl Stand  
Foam Roll Tube  
M10 x ¾” Allen Bolt  
1 5/8” Rubber Bumper  
M6 x 5/8” Philips Screw  
Leg Developer  
Leg Developer Axle  
Arm Curl Handle  
Arm Handle Sleeve  
Arm Curl Handle tube  
Handle Grip  
Right Base Frame  
Lock Knob  
1” Square End Cap  
Right Seat Support  
Rear Vertical Beam  
1
7/8” x 5/8” Leg Press Bushing 2  
M12 x 3” Allen Bolt  
Leg Press Diagonal Support  
Vertical Press Grip  
Left Seat Support  
1
2
2
1
1
1
1
1
1
17  
1
2
1
1
2
2
1
1
1
2
1
4
1
1
4
1
108” Upper Cable  
247” Front Press Cable  
83” Butterfly Cable  
82” Leg Press Cable  
Front Press Base  
M10 x 2” Allen Bolt  
M6 x 5/8” Philips Screw  
100 M10 x 2 ½” Carriage Bolt  
101 Ankle Strap  
102 298” Vertical Press Cable  
1
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WEIGHT RESISTANCE CHART  
WEIGHT PLATE  
Station  
1
2
3
4
5
6
7
8
9
Low Pulley  
Lat Pull  
40  
40  
50  
54  
55  
55  
68  
70  
60  
80  
80  
67  
93 105 116 127 138  
90 100 110 120 130  
Butterfly  
74  
80  
93 106 120  
Leg Press  
Front Press  
Vertical Press  
80 107 135 160 185 210 232 254 275  
54  
45  
80 107 116 125 135 162 189 215  
60  
76  
92 113 129 146 172 198  
WEIGHT PLATE  
Station  
10  
11 12 13 14 15 16 17 18 19  
Low Pulley  
Lat Pull  
150 162 174 186 198 210 222 234 246 258  
140 150 160 170 180 190 200 210 220 230  
133 146 159 172 185 198 211 224 237 250  
297 319 341 363 385 407 429 451 473 495  
241 267 293 319 345 371 397 423 449 475  
Butterfly  
Leg Press  
Front Press  
Vertical Press 218 238 258 278 298 318 338 358 378 398  
*Number s ar e appr oxi mat e. Act ual wei ght may var y.  
*Val ue f or but t er f l y i s f or each ar m.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPEX INC.  
LIMITED WARRANTY  
IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material,  
under normal use and service conditions, for a period of two years on the Frame from the date of  
purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this  
Warranty is limited to replacing or repairing, at IMPEX's option.  
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling  
IMPEX Customer Service Department at 1-800-999-8899. All freights on products returned to  
IMPEX must be prepaid by the customer. This warranty does not extend to any product or  
damage to a product caused by or attributable to freight damage, abuse, misuse, improper or  
abnormal usage or repairs not provided by an IMPEX authorized service center or for products  
used for commercial or rental purposes. No other warranty beyond that specifically set forth  
above is authorized by IMPEX.  
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or  
in connection with the use or performance of the product or other damages with respect to any  
economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, costs of  
removal, installation or other consequential damages or whatsoever natures. Some states do not  
allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above  
limitation may not apply to you.  
The warranty extended hereunder is in lieu of any and all other warranties and any implied  
warranties of merchantability or fitness for a particular purpose is limited in its scope and duration  
to the terms set forth herein. Some states do not allow limitations on how long an implied  
warranty lasts. Accordingly, the above limitation may not apply to you.  
This warranty gives you specific legal right. You may also have other rights which vary from state  
to state.  
IMPEX INC.  
14777 Don Julian  
City of Industry, CA 91746  
ORDERING REPLACEMENT PARTS  
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-  
999-8899 during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific  
standard time.  
When ordering replacement parts, always give the following information.  
1.  
2.  
3.  
4.  
Model  
Description of Parts  
Part Number  
Date of Purchase  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Graco Baby Swing PD173218A User Manual
Gravely Lawn Mower 990018 990020 User Manual
Havis Shields Automobile Accessories C 3190 User Manual
Healthrider Treadmill HRTL05910 User Manual
Honeywell Door RCWL2200A User Manual
Honeywell Marine Lighting SG 60 User Manual
Hotpoint Washer WMEF 742 User Manual
HP Hewlett Packard Calculator HP 6S User Manual
HP Hewlett Packard Network Card A4800A User Manual
HP Hewlett Packard Oven 45WDG PLUS User Manual