Impex Home Gym CB 349 User Manual

NOTE:  
Please read all instructions  
carefully before using this  
product  
Table of Contents  
Safety Notice  
COMPETITOR  
CB-349 BENCH  
Hardware Identifier  
Assembly Instruction  
Exploded Diagram  
Parts List  
Warranty  
Ordering Parts  
Model  
CB-349  
Retain This  
Manual for  
Reference  
July 15, 2004  
IMPEX INC.  
14777 Don Julian Rd., City of Industry, CA 91746  
Tel: (800) 999-8899 Fax (626) 961-9966  
OWNER'S  
MANUAL  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT SAFETY NOTICE  
PRECAUTIONS  
This exercise machine is built for optimum safety. However, certain precautions apply  
whenever you operate a piece of exercise equipment. Be sure to read the entire manual  
before you assemble or operate your machine. In particular, note the following safety  
precautions:  
1. Keep children and pets away from the machine at all times. DO NOT  
leave children unattended in the same room with the machine.  
2. Only one person at a time should use the machine.  
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal  
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.  
4. Position the machine on a clear, leveled surface. DO NOT use the machine  
near water or outdoors.  
5. Keep hands away from all moving parts.  
6. Always wear appropriate workout clothing when exercising. DO NOT wear  
robes or other clothing that could become caught in the machine. Running  
or aerobic shoes are also required when using the machine.  
7. Use the machine only for its intended use as described in this manual. DO  
NOT use attachments not recommended by the manufacturer.  
8. Do not place any sharp object around the machine.  
9. Disabled person should not use the machine without a qualified person or  
physician in attendance.  
10. Before using the machine to exercise, always do stretching exercises to  
properly warm up.  
11. Never operate the machine if the machine is not functioning properly.  
12. A spotter is recommended during exercise.  
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR  
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF  
35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL  
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES  
NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED  
BY OR THROUGH THE USE OF THIS PRODUCT.  
SAVE THESE INSTRUCTIONS.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY INSTRUCTION  
Tools required assembling the machine: Two Adjustable Wrenches and Allen  
Wrenches  
STEP 1  
(SEE Diagram 1)  
A.) Connect the two Rear Upright Beams (#1) by a Cross Brace (#15) in the Mid-span.  
Secure them with two M10 x 2 3/8” Hex Bolts (#2), four ¾” Washers (#3), one Bracket  
(#7), and two M10 Aircraft Nuts (#4) on each end of the Cross Brace.  
B.) Insert the Backrest Adjustment Bar (#10) through a selected hole to obtain desired incline  
of Backrest.  
C.) Insert two Bar Catches (#13) & (#14) into the selected hole on the Rear Upright Beams  
(#1) to obtain the desired height to hold the weight bar.  
DIAGRAM 1  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 2  
(SEE DIAGRAM 2)  
A.) Connect the Front Stabilizer (#42) to the Main Seat Support (#52) and secure them with  
two M10 x ¾” Hex Bolts (#46), four ¾” Washers (#3), and two M10 Aircraft Nuts (#4).  
DO NOT tighten the nuts and bolts yet.  
B.) Connect the Main Seat Support (#52) to the open bracket on the Cross Brace (#15).  
Secure the rear hole on the bracket with one M10 x 2 3/8” Bolt (#2), two ¾” Washers  
(#3), and one M10 Aircraft Nut (#4). Secure the other hole with a 3” Lock Pin (#8). Note:  
DO NOT over tighten the nut and bolt. The Main Frame needs to pivot on this bolt in able  
to fold up the bench.  
C.) Connect one end of Diagonal Support (#43) to the Main Seat Support (#52). Secure it  
with one M8 x 2 1/8” Hex Bolt (#48), two 5/8” Washers (#21) and one M8 Aircraft Nut  
(#49). Connect the other end to the Front Stabilizer. Secure it with one M8 x 5/8” Hex Bolt  
(#20) and 5/8” Washer (#21).  
D.) Securely tighten all the nuts and bolts previously installed.  
E.) Insert 6 ½” Long Lock Pin (#53) into the hole on the Main Seat Support (52). NOTE: The  
Pin is not designed to sustain any heavy weight. Only use the pin when changing the  
backrest board to a vertical position while doing Walk-in-Squat from the rear.  
DIAGRAM 2  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 3  
(SEE DIAGRAM 3)  
A.Attach the Leg Developer (#38) onto the bracket on the Front Stabilizer (#42). Secure it  
with a Hex Socket Axle (#44) and Hex Socket Screw (#45).  
B.) Insert two Foam Roll Tubes (#39) halfway through the hole on the Leg Developer (#38).  
Push four Foam Rolls (#37) onto the tubes from both sides.  
C.Place a Spring Clip (#34) onto the post on the Leg Developer .  
DIAGRAM 3  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 4  
(SEE DIAGRAM 4)  
A.) Attach the hole-side of the Backrest Supports (#16) onto both ends of the Pivot on the  
Main Seat Support (#52) and place the other side rest against the Backrest Adjustment  
Bar (#10).  
B.) Place the Backrest Board (#18) onto the Backrest Supports (#16). Secure it with four M6  
x 1 3/8” Hex Bolts (#50) and ½” Washers (#51).  
C.) Place Seat (#19) onto the bracket on the Main Seat Support (#52). Align the holes and  
secure the Seat with four M6 x 1 3/8” Hex Bolts (#50) and ½” Washers (#51).  
D.) Insert the Arm Curl Stand (#22) into the opening on the top of the Front Stabilizer (#42).  
Secure it with a Knob Bolt (#47).  
E.) Attach the Arm Curl Pad (#23) to the Arm Curl Stand (#22). Secure it with two M8 x 5/8”  
Hex Bolts (#20) and 5/8” Washers (#21).  
DIAGRAM 4  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 5  
(SEE Diagram 5)  
A.) Attach the ball end of the Cable to the Pulley (#28). Place the Pulley in the open slot on  
the Lat Bar Frame (#31). Secure it with one M10 x 2 1/8” Hex Bolt (#32), two Bushings  
(#29), two ¾” Washers (#3), and one M10 Aircraft Nut (#4).  
B.) Slide the Weight Holder (#33) onto the Lat Bar Frame from the bottom. Connect the  
Cable to the Holder with a Hook (#26).  
C.) Connect the Lat Bar (#25) to the Cable with a Hook (#26). When using the Lat Pull down,  
remove the Arm Curl and place it on the storage post behind the Rear Upright Beam.  
Then insert the Lat Bar Frame into the opening on the Front Stabilizer.  
DIAGRAM 5  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 6  
(SEE Diagram 6)  
A.) To store the bench in a vertical position, remove the Arm Curl and the Lat Bar Frame from  
the bench and place them onto the storage posts on the Rear Upright Beams.  
B.) Pull out the 3” Lock Pin (#8) on the Main Seat Support to fold up the bench. Make sure to  
re-insert the Lock Pin on the bracket to secure the vertical position.  
DIAGRAM 6  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PARTS LIST  
KEY NO.  
DESCRIPTION  
Rear Upright Beam  
M10 x 2 3/8” Hex Bolt  
¾” Washer  
M10 Aircraft Nut  
1 5/8” x 3 1/8” Square End Cap  
1 ¼” Square End Cap  
Bracket  
3” Short Lock Pin  
1” Round End Cap  
Backrest Adjustment Bar  
Bar Catch Panel  
¾” Bar Catch End Cap  
Right Bar Catch  
Left Bar Catch  
QUANTITY  
1
2
3
4
5
6
7
8
2
5
16  
8
6
2
2
1
7
1
2
2
1
1
1
2
2
1
1
3
5
1
1
2
1
2
1
1
2
4
1
1
1
4
3
4
4
1
2
2
2
1
1
1
1
2
1
1
1
8
8
1
1
1
2
2
2
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
47  
48  
49  
50  
51  
52  
53  
54  
55  
56  
57  
Cross Brace  
Backrest Support  
1” Square End Cap  
Backrest Board  
Seat  
M8 x 5/8” Hex Bolt  
5/8” Washer  
Arm Curl Stand  
Arm Curl Pad  
Handle Grip  
Lat Bar  
Hook  
Cable  
Pulley  
Pulley Bushing  
1 ½” Square End Cap  
Lat Bar Frame  
M10 x 2 1/8” Hex Bolt  
Weight Holder  
Spring Clip  
Sleeve  
1” Foam Roll End Cap  
Foam Roll  
Leg Developer  
Foam Roll Tube  
Plastic Bushing  
1 ¾” Square End Cap  
Front Stabilizer  
Diagonal Support  
Hex Socket Axle  
Hex Socket Screw  
M10 x ¾” Hex Bolt  
Knob Bolt  
M8 x 2 1/8” Hex Bolt  
M8 Aircraft Nut  
M6 x 1 3/8” Hex Bolt  
½” Washer  
Main Seat Support  
6 ½” Long Lock Pin  
Weight Bar  
Weight Plate 25#  
Weight Plate 15#  
Weight Plate 10#  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPEX INC.  
LIMITED WARRANTY  
IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use  
and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only  
to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's  
option.  
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Customer Service  
Department at 1-800-999-8899. All freights on products returned to IMPEX must be prepaid by the customer. This  
warranty does not extend to any product or damage to a product caused by or attributable to freight damage, abuse,  
misuse, improper or abnormal usage or repairs not provided by a IMPEX authorized service center or for products  
used for commercial or rental purposes. No other warranty beyond that specifically set forth above is authorized by  
IMPEX.  
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the  
use or performance of the product or other damages with respect to any economic loss, loss of property, loss of  
revenues or profits, loss of enjoyments or use, costs of removal, installation or other consequential damages or  
whatsoever natures. Some states do not allow the exclusion or limitation of incidental or consequential damages.  
Accordingly, the above limitation may not apply to you.  
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of  
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein.  
Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation may not  
apply to you.  
This warranty gives you specific legal right. You may also have other rights which vary from state to state. Register  
IMPEX INC.  
14777 Don Julian  
City of Industry, CA 91746  
ORDERING REPLACEMENT PARTS  
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-999-8899 during our  
regular business hours: Monday through Friday, 9 am until 5 pm Pacific standard time.  
When ordering replacement parts, always give the following information.  
1.  
2.  
3.  
4.  
Model  
Description of Parts  
Part Number  
Date of Purchase  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Graco Baby Swing ISPS055AA User Manual
Graco Car Seat 8482 User Manual
Graco Log Splitter 3A2573D User Manual
Harbor Freight Tools Grinder 92007 User Manual
Hearth and Home Technologies Indoor Fireplace Cinch Pipe Termination Cap System User Manual
Heath Zenith Door 598 1215 01 User Manual
Hotpoint Washer AQ1138D 697 S User Manual
HP Hewlett Packard Calculator HP OmniBook User Manual
IBM Printer 1xR User Manual
iHome Clock Radio IP18 User Manual