USER MANUAL
ENGLISH
ENGLISH
DEUTSCH
FRANCAIS
NEDERLANDS
Thank you very much for choosing the iiyama
LCD monitor.
We recommend that you take a few minutes to
read carefully through this brief but
comprehensive manual before installing and
switching on the monitor. Please keep this
manual in a safe place for your future
reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC DECLARATION OF CONFORMITY
Model Number:
Trade Name:
PL2201W / PL2202W
iiyama
Responsible party:
Address:
Ampronix Inc.
8697 Research Dr. Irvine, CA.92618 U.S.A.
949-788-9930
Telephone number:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This device has been tested and found to comply with the limits for Class B Personal Computers and
peripherals, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the device is operated in a residential environment. This device generates,
uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If you determine the device does cause harmful interference to radio
or television reception (this may be determined by monitoring the interference while turning the device off and
on), you are encouraged to try to correct the interference by one of the following measures:
„ Reorient or relocate the receiving antenna.
„ Increase the separation between the device and receiver.
„ Connect the device into an outlet on a circuit different from that to which the receiver
is connected.
„ Consult the dealer or an experienced radio or TV technician for help.
To meet the FCC requirements, you should use a signal cable with ferrite core at both ends.
CAUTION
Changes or modifications not expressly approved by iiyama could void the users authority
to operate the device under FCC compliance regulations.
CANADIAN DEPARTMENT OF COMMUNICATIONS COMPLIANCE
STATEMENT
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as
set out in the radio interference regulation of the Canadian department of communications.
CE MARKING DECLARATION OF CONFORMITY
This LCD monitor complies with the requirements of the EC Directive 89/336/EEC “EMC Directive” and 73/23/
EEC “Low Voltage Directive” as amended by Directive 93/68/EEC.
The electro-magnetic susceptibility has been chosen at a level that gives correct operation in residential areas,
business and light industrial premises and small-scale enterprises, inside as well as outside of the buildings.
All places of operation are characterised by their connection to the public low voltage power supply system.
„ We reserve the right to change specifications without notice.
„ All trademarks used in this user manual are the property of their respective owners.
„ As an ENERGY STAR® Partner, iiyama has determined that this product meets the ENERGY STAR® guidelines for
energy efficiency.
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
FOR YOUR SAFETY ..................................................................................... 1
SAFETY PRECAUTIONS ........................................................................ 1
SPECIAL NOTES ON LCD MONITORS .................................................... 3
CUSTOMERSERVICE ............................................................................. 3
CLEANING .............................................................................................. 3
BEFOREYOU OPERATETHE MONITOR ....................................................... 4
FEATURES .............................................................................................. 4
CHECKING THE CONTENTS OFTHE PACKAGE .................................... 5
FITTINGAND REMOVALOF BASE : ProLite E2201W ........................... 6
FITTINGAND REMOVALOF BASE : ProLite E2202WS / E2202WSV ... 6
CONTROLSAND CONNECTORS : ProLite E2201W .............................. 7
CONTROLSAND CONNECTORS : ProLite E2202WS / E2202WSV ...... 8
CONNECTING YOUR MONITOR : ProLite E2201W................................. 9
CONNECTING YOUR MONITOR : ProLite E2202WS / E2202WSV ........ 10
COMPUTERSETTING .............................................................................. 11
ADJUSTINGTHE VIEWINGANGLE ........................................................ 11
OPERATINGTHEMONITOR .......................................................................... 12
ADJUSTMENTMENUCONTENTS ........................................................... 13
SCREENADJUSTMENTS ........................................................................ 21
POWER MANAGEMENTFEATURE ......................................................... 24
TROUBLE SHOOTING ................................................................................... 25
APPENDIX ..................................................................................................... 27
SPECIFICATIONS : ProLite E2201W ....................................................... 27
SPECIFICATIONS : ProLite E2202WS ..................................................... 28
SPECIFICATIONS : ProLite E2202WSV .................................................. 29
DIMENSIONS : ProLite E2201W .............................................................. 30
DIMENSIONS : ProLite E2202WS / E2202WSV ....................................... 30
COMPLIANTTIMING ................................................................................ 31
CONNECTORPINASSIGNMENT ............................................................. 32
LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE
RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR
FEDERAL LAWS.
Hg
For disposal or recycling information, please contact your local authorities or the
Electronic Industries Alliance (www.eiae.org).
This information is only for U.S.A..
We recommend recycling of used product. Please contact your dealer or
iiyama service center. Recycle information is obtained via the Internet, using
You can access the Web page of different countries from there.
Download from Www.Somanuals.com. All Manuals Search And Download.
FOR YOUR SAFETY
SAFETY PRECAUTIONS
WARNING
STOP OPERATING THE MONITOR WHEN YOU SENSE TROUBLE
If you notice any abnormal phenomena such as smoke, strange sounds or fumes, unplug the monitor
and contact your dealer or iiyama service center immediately. Further use may be dangerous and
can cause fire or electric shock.
NEVER REMOVE THE CABINET
High voltage circuits are inside the monitor. Removing the cabinet may expose you to the danger of
fire or electric shock.
DO NOT PUT ANY OBJECT INTO THE MONITOR
Do not put any solid objects or liquids such as water into the monitor. In case of an accident, unplug
your monitor immediately and contact your dealer or iiyama service center. Using the monitor with
any object inside may cause fire, electric shock or damage.
INSTALL THE MONITOR ON A FLAT, STABLE SURFACE
The monitor may cause an injury if it falls or is dropped.
DO NOT USE THE MONITOR NEAR WATER
Do not use where water may be splashed or spilt onto the monitor as it may cause fire or electric
shock.
OPERATE UNDER THE SPECIFIED POWER SUPPLY
Be sure to operate the monitor only with the specified power supply. Use of an incorrect voltage will
cause malfunction and may cause fire or electric shock.
PROTECT THE CABLES
Do not pull or bend the power cable and signal cable. Do not place the monitor or any other heavy
objects on the cables. If damaged, the cables may cause fire or electric shock.
ADVERSE WEATHER CONDITIONS
It is advisable not to operate the monitor during a heavy thunder storm as the continual breaks in
power may cause malfunction. It is also advised not to touch the plug in these circumstances as it
may cause electric shock.
FOR YOUR SAFETY
1
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION
INSTALLATION LOCATION
Do not install the monitor where sudden temperature changes may occur, or in humid, dusty or smoky
areas as it may cause fire, electric shock or damage. You should also avoid areas where the sun
shines directly on the monitor.
DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION
The monitor may topple and cause injury if not suitably located. Please also ensure that you do not
place any heavy objects on the monitor, and that all cables are routed such that children may not pull
the cables and possibly cause injury.
MAINTAIN GOOD VENTILATION
Ventilation slots are provided to keep the monitor from overheating. Covering the slots may cause
fire. To allow adequate air circulation, place the monitor at least 10 cm (or 4 inches) from any walls.
Do not remove the tilt stand when operating the monitor. Ventilation slots on the back of the cabinet
will be blocked and the monitor may overheat if the stand is removed. This may cause fire or damage.
Operating the monitor on its back, side, upside down or on a carpet or any other soft material may
also cause damage.
DISCONNECT THE CABLES WHEN YOU MOVE THE MONITOR
When you move the monitor, turn off the power switch, unplug the monitor and be sure the signal
cable is disconnected. If you do not disconnect them, it may cause fire or electric shock.
UNPLUG THE MONITOR
If the monitor is not in use for a long period of time it is recommended that it is left unplugged to avoid
accidents.
HOLD THE PLUG WHEN DISCONNECTING
To disconnect the power cable or signal cable, always pull it by the plug. Never pull on the cable itself
as this may cause fire or electric shock.
DO NOT TOUCH THE PLUG WITH WET HANDS
Pulling or inserting the plug with wet hands may cause electric shock.
WHEN YOU INSTALL THE MONITOR ON YOUR COMPUTER
Be sure the computer is strong enough to hold the weight of the monitor, otherwise, you may damage
your computer.
DO NOT PUT FLOPPY DISKS NEAR THE SPEAKERS
(For ProLite E2202WS / E2202WSV)
Magnetically recorded data, such as on a floppy disk, may become corrupted by the magnetic field
produced by the speakers if the disks are placed on or near the speakers.
OTHERS
ERGONOMIC RECOMMENDATIONS
To eliminate eye fatigue, do not operate the monitor against a bright background or in a dark room. For
optimal viewing comfort, the monitor should be just below eye level and 40-60 cm (16-24 inches)
away from your eyes. When using the monitor over a prolonged time, a ten minute break every hour
is recommended as looking at the screen continuously can cause eye strain.
2
FOR YOUR SAFETY
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL NOTES ON LCD MONITORS
The following symptoms are normal with LCD monitors and do not indicate a problem.
When you first turn on the LCD monitor, the picture may not fit in the display area
because of the type of computer that is used. In this case, adjust the picture
position to the correct position.
NOTE
„
Due to the nature of the backlight, the screen may flicker during initial use. Turn off
the Power Switch and then turn it on again to make sure the flicker disappears.
You may find slightly uneven brightness on the screen depending on the desktop
pattern you use.
„
„
„
Due to the nature of the LCD screen, an afterimage of the previous screen may
remain after switching the image, when the same image is displayed for hours. In
this case, the screen is recovered slowly by changing the image or turning off the
Power Switch for hours.
„
Contact your dealer or iiyama service center for the backlight replacement when the
screen is dark, flickering or not lighting up. Never attempt to replace it by yourself.
CUSTOMER SERVICE
„
The fluorescent light used in the LCD monitor may have to be periodically replaced.
For the warranty coverage on this component, please check with local iiyama
service center.
NOTE
If you have to return your unit for service and the original packaging has been
discarded, please contact your dealer or iiyama service center for advice or
replacement packaging.
„
CLEANING
WARNING
CAUTION
NOTE
If you drop any materials or liquids such as water into the monitor when cleaning,
unplug the power cable immediately and contact your dealer or iiyama service center.
„
„ For safety reasons, turn off the power switch and unplug the monitor before you
clean it.
To protect the LCD panel, do not scratch or rub the screen with a hard object.
„
„
Never use any of the following strong solvents. These will damage the cabinet and
the LCD screen.
Spray-type cleaner
Wax
Thinner
Benzine
Acid or Alkaline solvent
Abrasive cleaner
Touching the cabinet with any product made from rubber or plastic for a long time
may cause degeneration or loss of paint on the cabinet.
„
Stains can be removed with a cloth lightly moistened with a mild detergent solvent. Then
wipe the cabinet with a soft dry cloth.
CABINET
LCD
Periodic cleaning with a soft dry cloth is recommended.
SCREEN
Don't use tissue paper etc. because these will damage the LCD screen.
FOR YOUR SAFETY
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU OPERATE THE MONITOR
FEATURES
‹ ProLite E2201W : 56cm (22") TFT Color LCD Monitor
‹ ProLite E2202WS / E2202WSV : 55cm (22") TFT Color LCD Monitor
‹ Supports Resolutions up to 1680 × 1050
‹ High Contrast 2000:1(DCR) / High Brightness 300cd/m2 / Quick Response Time
2ms (Gray to Gray): ProLite E2201W
‹ High Contrast 2000:1(DCR) / High Brightness 300cd/m2 : ProLite E2202WS /
E2202WSV
‹ Multi-Color Control
Supports sRGB International Standard
‹ Gamma Control
Clear Display for Moving Pictures & Photographs
‹ Digital Character Smoothing
‹ Automatic Set-up
‹ Stereo Speakers: ProLite E2202WS / E2202WSV
2 × 2W Stereo Speakers
‹ Economy Mode
Reduced Power Consumption
‹ Plug & Play VESA DDC2B Compliant
Windows® 95/98/2000/Me/XP/Vista Compliant
‹ DDC/CI Compliant
Screen adjustments can be made from your computer by using the compliant
software (softOSM).
‹ Power Management (ENERGY STAR® and VESA DPMS Compliant)
‹ Ergonomic Design
TCO ’03 and TÜV-ErgonomicsApproved
‹ Digital Input (DVI-D, HDCP Compliant) for Clear Display : ProLite E2201W / E2202WS
‹ VESA Mounting Standard (100mm×100mm) Compliant
4
BEFORE YOU OPERATE THE MONITOR
Download from Www.Somanuals.com. All Manuals Search And Download.
CHECKING THE CONTENTS OF THE PACKAGE
The following accessories are included in your package. Check to see if they are enclosed with the
monitor. If anything is missing or damaged, please contact your local iiyama dealer or regional iiyama
office.
„ Power Cable*1
„ DVI-D Signal Cable*2
„ Stand
„ D-Sub Signal Cable
„ Audio Cable*3
„ Cable Holder
„ User Manual
1
CAUTION
The rating of the Power Cable enclosed in 120V area is 10A/125V. If you are using
a power supply higher than this rating, then a power cable with a rating of 10A/
250V must be used.
*
However, all guarantees and warranties are void for any problems or damage
caused by a power cable not supplied by iiyama.
2
Accessory for ProLite E2201W / ProLite E2202WS
*
3
Accessory for ProLite E2202WS / ProLite E2202WSV
*
<softOSM>
The Desktop softOSM software complies with the DDC/CI standard and can be downloaded from the
iiyama website.
softOSM Software Functions
„ Easy access to the range of user adjustments can be via the softOSM Software rather than the
buttons located on the display itself.
„ The communication between software and display occurs through the Display Cable provided;
hence no special cabling is required.
Compatible with Windows 98, 2000, XP and Vista.
BEFORE YOU OPERATE THE MONITOR
Download from Www.Somanuals.com. All Manuals Search And Download.
5
FITTING AND REMOVAL OF BASE : ProLite E2201W
„ Install the stand on a stable surface. The monitor may cause injury or damage if it
falls or is dropped.
CAUTION
„ Do not give a strong impact to the monitor. It may cause damage.
Unplug the monitor before installation to avoid electric shock or damage.
„
<Install>
<Remove>
Press the stopper at the back of the stand
and remove the stand from the post.
Hold the monitor and push the post down
into the stand.
Press the stopper
Stand
FITTING AND REMOVAL OF BASE : ProLite E2202WS / E2202WSV
Install the stand on a stable surface. The monitor may cause injury or damage if it
falls or is dropped.
„
CAUTION
„ Do not give a strong impact to the monitor. It may cause damage.
„ Unplug the monitor before installation to avoid electric shock or damage.
<Remove>
<Install>
Press the stopper at the back of the stand
and remove the stand from the post.
Hold the monitor and push the post down
into the stand.
Press the stopper
Stand
6
BEFORE YOU OPERATE THE MONITOR
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS AND CONNECTORS : ProLite E2201W
<Front>
)
<Back>
Power Switch (
A
B
C
D
E
F
Menu Button (MENU)
+ Button ( + )
– Button ( – )
Auto Button (AUTO)
Input Button (SOURCE)
Power Indicator
G
NOTE Blue:
Normal operation
Orange: Power Management
„ Auto (Signal Select)
When no signal is received from the system, the display enters into its
Power Management Mode reducing power consumption to < than 2W.
„ Analog / Digital (Signal Select)
The monitor enters into power management mode which reduces the power
consumption to less than 2W when receiving no horizontal and/or vertical
sync signal.
D-sub mini 15pin Connector (D-SUB)
H
I
DVI-D 24pin Connector (DVI-D)
Keyhole for Security Lock
J
You can fasten a security lock and cable to prevent the monitor from being removed
without your permission.
K AC Connector (AC IN)
NOTE
BEFORE YOU OPERATE THE MONITOR
Download from Www.Somanuals.com. All Manuals Search And Download.
7
CONTROLS AND CONNECTORS : ProLite E2202WS / E2202WSV
<Front>
)
<Back>
Power Switch (
A
B
C
D
E
F
Menu Button (MENU)
+ Button (
– Button (
)
)
Auto Button (AUTO)
Input Button (SOURCE)*
Power Indicator
G
NOTE Blue:
Orange: Power Management
„ Auto (Signal Select)
Normal operation
When no signal is received from the system, the display enters into its
Power Management Mode reducing power consumption to < than 2W.
„ Analog / Digital (Signal Select)
The monitor enters into power management mode which reduces the power
consumption to less than 2W when receiving no horizontal and/or vertical
sync signal.
Speakers
H
I
AC Connector (AC IN)
Audio Connector (
)
J
K DVI-D 24pin Connector (DVI-D)*
D-sub mini 15pin Connector (D-SUB)
M Keyhole for Security Lock
You can fasten a security lock and cable to prevent the monitor from being removed
without your permission.
L
NOTE
Available for ProLite E2202WS only.
*
8
BEFORE YOU OPERATE THE MONITOR
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING YOUR MONITOR : ProLite E2201W
Ensure that both the computer and the monitor are switched off.
A
B
Connect the computer to the monitor with the signal cable. (See page 32 for CONNECTOR PIN
ASSIGNMENT.)
Connect the Power Cable to the monitor first and then to the power supply.
C
NOTE „ The signal cables used for connecting the computer and monitor may vary with the type of
computer used. An incorrect connection may cause serious damage to both the monitor and
the computer. The cable supplied with the monitor is for a standard 15 pin D-Sub connector.
If a special cable is required please contact your local iiyama dealer or regional iiyama office.
„ For connection to Macintosh computers, contact your local iiyama dealer or regional
iiyama office for a suitable adaptor.
„ Make sure you tighten the finger screws at each end of the signal cable.
[Example of Connection]
<Back>
D-Sub Signal Cable
Power Cable
(Accessory)
(Accessory)
DVI-D Signal Cable
(Accessory)
Computer
[ Fitting of Cable Holder ]
Collect cables at the back of the stand.
A
B
Position the Cable Holder at the base of the
stand column by inserting the ‘tabs’ into the
guide holes. Apply gentle pressure downwards
to secure.
Ãáâìå Èïìäåò
Stand
[ Removal of Cable Holder ]
Remove Cable Holder by sliding up the base
column.
A
BEFORE YOU OPERATE THE MONITOR
Download from Www.Somanuals.com. All Manuals Search And Download.
9
CONNECTING YOUR MONITOR : ProLite E2202WS / E2202WSV
Ensure that both the computer and the monitor are switched off.
A
B
Connect the computer to the monitor with the signal cable. (See page 32 for CONNECTOR PIN
ASSIGNMENT.)
Connect the monitor to the audio equipment with the Audio Cable when using the audio features.
C
D Connect the Power Cable to the monitor first and then to the power supply.
NOTE „ The signal cables used for connecting the computer and monitor may vary with the type of
computer used. An incorrect connection may cause serious damage to both the monitor and
the computer. The cable supplied with the monitor is for a standard 15 pin D-Sub connector.
If a special cable is required please contact your local iiyama dealer or regional iiyama office.
„ For connection to Macintosh computers, contact your local iiyama dealer or regional
iiyama office for a suitable adaptor.
„ Make sure you tighten the finger screws at each end of the signal cable.
[Example of Connection]
<Back>
Power Cable
(Accessory)
D-Sub Signal Cable
(Accessory)
DVI-D Signal Cable*
Audio Cable (Accessory)
Computer
Available for ProLite E2202WS only.
*
[ Fitting of Cable Holder ]
Collect cables at the back of the stand.
A
B
Position the Cable Holder at the base of the
stand column by inserting the ‘tabs’ into the
guide holes. Apply gentle pressure downwards
to secure.
Ãáâìå Èïìäåò
Stand
[ Removal of Cable Holder ]
Remove Cable Holder by sliding up the base
column.
A
10 BEFORE YOU OPERATE THE MONITOR
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER SETTING
„ Signal Timing
Change to the desired signal timing listed on page 31: COMPLIANT TIMING.
„ Windows 95/98/2000/Me/XP/Vista Plug & Play
The iiyama LCD monitor complies with DDC2B of VESA standard. The Plug & Play function runs on
Windows 95/98/2000/Me/XP/Vista by connecting the monitor to DDC2B compliant computer with
the Signal Cable supplied. Windows 95/98/2000/Me/XP/Vista Monitor Information File for iiyama
monitors may be necessary for your computer and obtained via the Internet, using the address:
„ For additional information on how to download the driver for your monitor, please
NOTE
access one of the internet sites noted above.
„ Monitor Drivers are not required in most cases for Macintosh or Unix operating systems.
For further information, please contact your computer dealer first for advice.
ADJUSTING THE VIEWING ANGLE
„ For optimal viewing it is recommended to look at the full face
of the monitor.
„ Hold the stand so that the monitor does not topple when you
change the monitor’s angle.
„ You are able to adjust the monitor’s angle up to 20 degrees
upward, 5 degrees downward.
„ In order to ensure a healthy and relaxed body position when
20
using the monitor at visual display workstations, it is
recommended that the adjusted tilt angle should not exceed
5
10 degrees. Adjust the monitor’s angle to your own preference.
NOTE „ Do not touch the LCD screen when you change the
angle. It may cause damage or break the LCD screen.
„ Careful attention is required not to catch your fingers
or hands when you change the angle.
BEFORE YOU OPERATE THE MONITOR 11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING THE MONITOR
To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT
TIMING shown on page 31. You are also able to adjust the picture by following the button operation
shown below. For more detailed adjustments, see page 21 for SCREEN ADJUSTMENTS.
Press the Menu Button to start the On Screen Display feature. There are
additional Menu pages which can be switched by using the +/– Buttons.
Displayed while Lock Out is active.
(
Displayed while Mute is active.
DCR setting is displayed.
Displayed while sRGB is active.
Displayed while Economy Mode is active.
Page no.
DCR
OFF
Menu:1
1
sRGB
LOCK
Adjustment icon
Current horizontal frequency,
vertical refresh rate
and resolution
1680 × 1050
H : 6 5 . 4 K H z V : 6 0 . 1 H z
Select the Menu page which contains the adjustment icon relating to the
adjustment you want to make. Press the Menu Button again. Then, use the
+/– Buttons to highlight the desired adjustment icon. Press the Menu Button
again.
B
C
Use the +/– Buttons to make the appropriate adjustment or setting.
For example, to correct for vertical position, select Menu page number 1 and then press the Menu
Button. Then, select
(V-Position) by using the +/– Buttons.
DCR
OFF
Menu:1
1680 × 1050
H : 6 5 . 4 K H z V : 6 0 . 1 H z
An adjustment scale appears after you press the Menu Button. Use the +/– Buttons to change the
vertical position settings. The vertical position of the overall display should be changing accordingly
while you are doing this.
V-Position
The bar shows
the progress of the
+
–
50
adjustment being made.
NOTE
„ When button operations are aborted during adjustment, On-Screen Display disappears when the
time set for the OSD Off Timer has passed. The Auto Button can be used to exit OSD window
immediately.
Any changes are automatically saved in the memory when the On Screen Display disappears.
Turning off the power should be avoided while using the Menu.
„
„
Adjustments for Clock, Phase and Position are saved for each signal timing. Except for these
adjustments, all other adjustments have only one setting which applies to all signal timings.
12 OPERATING THE MONITOR
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENT MENU CONTENTS
Direct
You can skip the Menu pages and display an adjustment scale directly by using the
following button operations.
z Brightness / Contrast / Volume*1 / DCR: To display direct menu press either of the +/- Buttons.
Continue to use the +/- Buttons to select the adjustments
required.
DCR
z DCR:
Select on the Direct Menu.
Off: Typical Contrast Ratio
On: Increased Contrast Ratio
DCR adjusts brightness according to the image, and improve the contrast ratio
up to 2000:1 during move playing.
NOTE
Brightness, sRGB and Economy Mode cannot be adjusted and selected while
DCR is active.
z Auto Set-up:
Press the Auto Button when the Menu is not displayed.
z Volume (Mute)*1: With the OSD menu off, the pressing and holding of the Menu Button for 1-2
seconds will enable/disable the Audio Mute facility.
z Signal Select*2: With the OSD menu off, pressing the Input Button will switch the input signal
from Analogue to Digital.
z Lock Out:
With the OSD menu off, pressing and holding the Menu and ‘-‘ Buttons
simultaneously for a period of at least 7 seconds will enable and disable the OSD
Lock Out mode.
is displayed while Lock Out is active.
1
Available for ProLite E2202WS / E2202WSV only.
Available for ProLite E2201W / E2202WS only.
*
2
*
OPERATING THE MONITOR 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Analog Input
Menu : 1
(Analog)
DCR
OFF
Menu:1
1680 × 1050
H : 6 5 . 4 K H z V : 6 0 . 1 H z
Adjustment Item
Brightness *1
Problem / Option
Button to Press
Too dark
Direct
Too bright
Too dull
Direct
Contrast
Too intense
Clock *2
To correct flickering text or lines
Phase *2
To correct flickering text or lines
Too low
Too high
V-Position
H-Position
Return to Menu
Too far to the left
Too far to the right
Highlight “Menu : 1” again.
*1 Adjust the Brightness when you are using the monitor in a dark room and feel the screen is too
bright.
*2 See page 21 for SCREENADJUSTMENTS.
See page 13 for Direct adjustment.
Direct
14 OPERATING THE MONITOR
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu : 2
(Analog)
DCR
OFF
Menu:2
1680 × 1050
H : 6 5 . 4 K H z V : 6 0 . 1 H z
Adjustment Item
Problem / Option
Button to Press
NO
Return to Menu.
Auto Set-up *3
Adjust Clock, Phase, V-Position and H-Position
automatically.
YES
Direct
Setting
Off The Auto Set-up is not performed when the
signal input is changed.
Adjust Clock, Phase, V-Position and H-Position
automatically when the signal input is changed.
On
NOTE „ The brightness of screen varies for several seconds during the adjustment.
„ This function is not performed automatically when changing the signal input because
the factory-preset of “Setting” in Auto Set-up is set to Off.
1
2
Color 1: 9300K
Color 2: 7500K
Color 3: 6500K
sRGB
Color Temp.
3
s
R
G
B
Too weak
Too strong
(User)
NOTE „ sRGB is an international standard which defines and unifies the difference of color
appearance between equipment.
„ You can not adjust the Brightness, Contrast, Gamma and Economy Mode during sRGB
mode because those settings are locked.
„
is displayed while sRGB is active.
Sharpness
1 2 3 4 5
Adjust the picture quality at resolutions of less than 1680 ×
1050.
You can change the picture quality from 1 to 5 (sharp to soft).
Press the + Button to change the picture quality in numerical
order. Press the – Button to change the picture quality in reverse
numerical order.
*3 For best results, use the Auto Set-up in conjunction with the adjustment pattern. See page 21 for
SCREENADJUSTMENTS.
See page 13 for Direct adjustment.
Direct
OPERATING THE MONITOR 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu : 2
(Analog)
Adjustment Item
Problem / Option
Off
Normal
Gamma
Mode1
Mode2
Off
High contrast
Dark
Normal
Economy Mode
Mode1
Brightness of back-light is reduced.
Brightness of back-light is reduced more than Mode1.
Mode2
NOTE
„
is displayed while Economy Mode is active.
Return to Menu
Highlight “Menu : 2” again.
16 OPERATING THE MONITOR
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu : 3
(Analog)
DCR
OFF
Menu:3
1680 × 1050
H : 6 5 . 4 K H z V : 6 0 . 1 H z
Problem / Option
Too soft
Button to Press
Adjustment Item
Volume *1
Direct
Too loud
NOTE
„
is displayed while Mute is active.
1 2 3 4 5
OSD Position
You can move the OSD display area
to any one of the following 5 positions
within the overall display:
Press the + Button to move the OSD in numerical order. Press
the – Button to move the OSD in reverse numerical order.
Set the OSD Off Timer for 3-60 seconds.
OSD Off Timer
Language
English
Deutsch
Français
Auto
English
German
French
Español
Italiano
Spanish
Italian
Japanese
Select the signal input automatically.
Select the Analog input (D-SUB).
Select the Digital input (DVI-D).
Signal Select *2 Direct
Analog
Digital
When both Analogue and Digital cables are connected, you can switch between them
using the direct access facility described earlier. If only one input is present, this will
automatically be selected. In Power Management Mode input switching is disabled.
NOTE
NO
Return to Menu.
Reset
YES
Factory-preset data is restored.
Return to Menu
Highlight “Menu : 3” again.
1
Available for ProLite E2202WS / E2202WSV only.
Available for ProLite E2201W / E2202WS only.
*
2
*
See page 13 for Direct adjustment.
Direct
OPERATING THE MONITOR 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital Input : Available for ProLite E2201W / ProLite E2202WS only.
DCR
OFF
Menu:1
1680 × 1050
H : 6 5 . 4 K H z V : 6 0 . 1 H z
Adjustment Item
Problem / Option
Button to Press
Too dark
Brightness *1
Direct
Direct
Too bright
Too dull
Contrast
Too intense
1
2
3
s
Color 1: 9300K
Color Temp.
Color 2: 7500K
Color 3: 6500K
sRGB
R
G
B
Too weak
Too strong
User
„ sRGB is an international standard which defines and unifies the difference of color
appearance between equipment.
NOTE
„ You can not adjust the Brightness, Contrast, Gamma and Economy Mode during sRGB
mode because those settings are locked.
„
is displayed while sRGB is active.
Sharpness
1 2 3 4 5
Adjust the picture quality at resolutions of less than 1680
× 1050.
You can change the picture quality from 1 to 5 (sharp to soft).
Press the + Button to change the picture quality in
numerical order. Press the – Button to change the picture
quality in reverse numerical order.
Off
Normal
Gamma
High contrast
Dark
Mode1
Mode2
*1 Adjust the Brightness when you are using the monitor in a dark room and feel the screen is too
bright.
See page 13 for Direct adjustment.
Direct
18 OPERATING THE MONITOR
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu : 1
(Digital)
Adjustment Item
Problem / Option
Normal
Off
Economy Mode
Mode1
Mode2
Brightness of back-light is reduced.
Brightness of back-light is reduced more than Mode1.
NOTE
„
is displayed while Economy Mode is active.
Return to Menu
Highlight “Menu : 1” again.
OPERATING THE MONITOR 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu : 2
(Digital)
DCR
OFF
Menu:2
1680 × 1050
H : 6 5 . 4 K H z V : 6 0 . 1 H z
Problem / Option
Too soft
Button to Press
Adjustment Item
Volume *1
Direct
Too loud
NOTE
„
is displayed while Mute is active.
1 2 3 4 5
OSD Position
You can move the OSD display area
to any one of the following 5 positions
within the overall display:
Press the + Button to move the OSD in numerical order. Press
the – Button to move the OSD in reverse numerical order.
Set the OSD Off Timer for 3-60 seconds.
OSD Off Timer
Language
English
English
Español
Italiano
Italian
Deutsch
German
Français
Auto
French
Japanese
Select the signal input automatically.
Select the Analog input (D-SUB).
Select the Digital input (DVI-D).
Signal Select
Direct
Analog
Digital
When both Analogue and Digital cables are connected, you can switch between them
using the direct access facility described earlier. If only one input is present, this will
automatically be selected. In Power Management Mode input switching is disabled.
NOTE
NO
Return to Menu.
Reset
YES
Factory-preset data is restored.
Return to Menu
Highlight “Menu : 2” again.
*1 Available for ProLite E2202WS only.
See page 13 for Direct adjustment.
Direct
20 OPERATING THE MONITOR
Download from Www.Somanuals.com. All Manuals Search And Download.
SCREEN ADJUSTMENTS
Adjust the image by following the procedure below to get the desired picture when selecting Analog input.
„ The screen adjustments described in this manual are designed to set image position and minimize
flicker or blur for the particular computer in use.
„ The monitor is designed to provide the best performance at resolution of 1680 × 1050, but can not
provide the best at resolutions of less than 1680 × 1050 because the picture is automatically stretched
to fit the full screen. It is recommended to operate at resolution of 1680 × 1050 in normal use.
„ Displayed text or lines will be blurred or irregular in thickness when the picture is stretched due to
the screen enlargement process.
„ It is preferable to adjust the image position and frequency with the monitor controls, rather than the
computer software or utilities.
„ Perform adjustments after a warm-up period of at least thirty minutes.
„ Additional adjustments may be required after the Auto Set-up depending on the resolution or signal
timing.
„ The Auto Set-up may not work correctly when displaying the picture other than the screen
adjustment pattern. In this case, manual adjustments are required.
There are two ways to adjust the screen. One way is automatic adjustment for Clock, Phase and
Position. The other way is performing each adjustment manually.
Perform the Auto Set-up first when the monitor is connected to a new computer, or resolution is
changed. If the screen has a flicker or blur, or the picture does not fit in the display area after
performing the Auto Set-up, manual adjustments are required. Both adjustments should be made by
using the screen adjustment pattern (Test.bmp) obtained via the IIYAMA web site (http://
www.iiyama.com).
Adjust the image by following the procedure below to get the desired picture.
This manual explains adjustment under Windows 95/98/2000/Me/XP/Vista.
Display the picture at the optimum resolution.
A
B
Enter the Test.bmp (screen adjustment pattern) to wallpaper.
NOTE
„ Consult the appropriate documentation for doing this.
„ Test.bmp is made at resolution of 1280 × 1024. Set the display position to center in the
wallpaper setting dialogue box. If you use Microsoft® PLUS! 95/98 cancel the setting
of “Stretch desktop wallpaper to fit the screen”.
[Adjustment pattern]
Color bar
Zebra pattern
Picture frame
This is the image
displayed at 1280 × 1024.
OPERATING THE MONITOR 21
Download from Www.Somanuals.com. All Manuals Search And Download.
Press the Auto Button. (Auto Set-up)
C
D
Adjust the image manually by following procedure below when the screen has a
flicker or blur, or the picture does not fit in the display area after performing the Auto
Set-up.
Adjust the V-Position so that the top and bottom of the picture frame will fit to the
display area.
E
+
–
1) Adjust the H-Position so that the left side of the picture frame will move to the left
edge of the display area.
F
+
–
2) Stretch the right side of the picture frame to the right edge of the display area by
adjusting the Clock.
+
–
„ When the left side of the picture frame moves apart from the left edge of the display
NOTE
area during the Clock adjustment, adjust steps 1) and 2).
„ Another way to make the Clock adjustment is to correct the vertical wavy lines in the
zebra pattern.
„ The picture may flicker during the Clock, H-Position and V-Position adjustment.
„ In case the picture frame is bigger or smaller than the data display area after the Clock
adjustment, repeat steps from
.
C
22 OPERATING THE MONITOR
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjust the Phase to correct horizontal wavy noise, flicker or blur in the zebra pattern.
G
+
–
„ In case the strong flicker or blurs remain on a part of the screen, repeat steps
NOTE
and
F
because the Clock may not be adjusted correctly. If the flicker or blurs still remain,
G
set the refresh rate of computer to low (60Hz) and repeat steps from
again.
C
„ Adjust the H-Position after the Phase adjustment if the horizontal position moves
during the adjustment.
Adjust the Brightness and Color Temp. to get the desired picture after you complete
the Clock and Phase adjustments.
H
Put back your favorite wallpaper.
OPERATING THE MONITOR 23
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER MANAGEMENT FEATURE
The power management feature of this product complies with power saving requirement of ENERGY
STAR® and VESA DPMS. When activated, it automatically reduces unnecessary power consumption
of the monitor when your computer is not in use.
To use the feature, the monitor needs to be connected to a VESA DPMS compliant computer. There
is a power management step the monitor takes as described below. The power management function,
including any timer settings is configured by the operating system. Check your operating system
manual for information on how this can be configured.
Power Management Mode
„
When the H-sync signal / V-sync signal / H and V sync signals from the computer are off, the
monitor enters into Power Management Mode which reduces the power consumption to less than
2W. The screen becomes dark, and the power indicator turns to orange. From Power Management
Mode, the image reappears in several seconds when either the keyboard or the mouse are
touched again.
Power Indicator
NORMAL MODE
Blue
POWER MANAGEMENT MODE
Orange
POWER
0
2W
100%
CONSUMPTION
Even when using the power management mode, the monitor consumes electricity. Turn
off the Power Switch whenever the monitor is not in use, during the night and weekends,
to avoid unnecessary power consumption.
NOTE
„
„
It is possible that the video signal from the computer may be on while the H or V sync
signal is missing. In this instance, the POWER MANAGEMENT feature may not work
properly.
24 OPERATING THE MONITOR
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE SHOOTING
If the monitor fails to operate correctly, please follow the steps below for a possible solution.
1. Perform the adjustments described in OPERATING THE MONITOR, depending on the problem you
have. If the monitor does not get a picture, skip to 2.
2. Consult the following items if you cannot find an appropriate adjustment item in OPERATING THE
MONITOR or if the problem persists.
3.
If you are experiencing a problem which is not described below or you cannot correct the
problem, discontinue using the monitor and contact your dealer or iiyama service center for
further assistance.
Problem
Check
The picture does
not appear.
A
(Power indicator
does not light up.)
† The Power Cable is firmly seated in the socket.
† The Power Switch is turned ON.
† The AC socket is live. Please check with another piece of equipment.
(Power indicator
is blue.)
† If the blank screen saver is in active mode, touch the keyboard or the
mouse.
†
†
Increase the Contrast and/or Brightness.
The computer is ON.
† The Signal Cable is properly connected.
† The signal timing of the computer is within the specification of the monitor.
(Power indicator † If the monitor is in power management mode, touch the keyboard or the
is orange.)
mouse.
The computer is ON.
†
† The Signal Cable is properly connected.
†
The signal timing of the computer is within the specification of the monitor.
The screen is not † The Signal Cable is properly connected.
B
synchronized.
† The signal timing of the computer is within the specification of the monitor.
† The video output level of the computer is within the specification of the
monitor.
The screen
position is not in
the center.
† The signal timing of the computer is within the specification of the monitor.
C
D
E
The screen is
too bright or too
dark.
† The video output level of the computer is within the specification of the
monitor.
† The power voltage is within the specification of the monitor.
The screen is
shaking.
†
The signal timing of the computer is within the specification of the monitor.
TROUBLE SHOOTING 25
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
No sound.*
Check
† The audio equipment (computer etc.) is ON.
† The Audio Cable is properly connected.
† The Volume is turned up.
F
† The Mute is OFF.
† The audio output level of the audio equipment is within the specification of
the monitor.
The sound is too* † The audio output level of the audio equipment is within the specification of
G
H
the monitor.
loud or too quiet.
† The Audio Cable is properly connected.
A strange noise is*
heard.
* Available for ProLite E2202WS / E2202WSV only.
26 TROUBLE SHOOTING
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
SPECIFICATIONS: ProLite E2201W
LCD Panel
a-Si TFT Active Matrix
Diagonal: 56cm / 22"
Driving system
Size
Pixel pitch
Brightness
Contrast ratio
0.282mm H × 0.282mm V
300cd/m2 (Typical)
1000 : 1 (Typical), 2000:1 (DCR)
Viewable angle Right / Left: 85 degrees each, Up / Down: 80 degrees each
Response time
5ms (Black, white, black), 2ms (Gray to Gray)
Approx. 16.7 million maximum
Display Colors
Sync Frequency
Analog: Horizontal 24.0-80.0kHz, Vertical 55-75Hz
Digital: Horizontal 31.0-80.0kHz, Vertical 55-75Hz
Dot Clock
162MHz maximum
Maximum Resolution
Input Connector
Plug & Play
1680 × 1050, 1.8 MegaPixels
D-Sub mini 15pin, DVI-D 24pin
VESA DDC2BTM
Separate sync: TTL, Positive or Negative
Input Sync Signal
Input Video Signal
Analog: 0.7Vp-p (Standard), 75Ω, Positive
Digital: DVI (Digital Visual Interface Standard Rev.1.0) compliance
Maximum Screen Size
Power Source
473.8mm W × 296.1mm H / 18.7" W × 11.7" H
100-240VAC, 50/60Hz, 1.5A
Power Consumption
Dimensions / Net Weight
Tilt Angle
49W maximum, Power management mode: 2W maximum*
507.0 × 410.5 × 209.5mm / 20.0 × 16.2 × 8.3" (W×H×D), 5.8kg / 12.8lbs
Up: 20 degrees, Down: 5 degrees
Operating: Temperature 5 to 35°C / 41 to 95°F
Environmental
Humidity
Storage: Temperature -20 to 60°C / -4 to 140°F
Humidity 5 to 85% (No condensation)
10 to 80% (No condensation)
Considerations
Approvals
TCO ’03, CE, TÜV-GS, TÜV-Ergonomics, FCC-B, UL/ C-UL, VCCI-B,
GOST-R, CCC
NOTE
* Condition: Audio equipment is not connected.
APPENDIX 27
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS: ProLite E2202WS
LCD Panel Driving system
Size
a-Si TFT Active Matrix
Diagonal: 55cm / 22"
Pixel pitch
0.277mm H × 0.277mm V
300cd/m2 (Typical)
Brightness
Contrast ratio
1000 : 1 (Typical), 2000:1 (DCR)
Viewable angle Right / Left / Up / Down: 80 degrees each
Response time
Display Colors
5ms (Black, white, black)
Approx. 16.7 million maximum
Sync Frequency
Analog: Horizontal 24.0-80.0kHz, Vertical 55-75Hz
Digital: Horizontal 31.0-80.0kHz, Vertical 55-75Hz
Dot Clock
162MHz maximum
Maximum Resolution
Input Connector
Plug & Play
1680 × 1050, 1.8 MegaPixels
D-Sub mini 15pin, DVI-D 24pin
VESA DDC2BTM
Separate sync: TTL, Positive or Negative
Input Sync Signal
Input Video Signal
Analog: 0.7Vp-p (Standard), 75Ω, Positive
Digtal: DVI (Digital Visual Interface Standard Rev.1.0) compliance
Input Audio Connector
Input Audio Signal
Speakers
ø 3.5mm mini jack (Stereo)
0.7Vrms maximum
2.0W × 2 (Stereo speakers)
Maximum Screen Size
Power Source
464.9mm W × 290.6mm H / 18.3" W × 11.4" H
100-240VAC, 50/60Hz, 1.5A
Power Consumption
Dimensions / Net Weight
Tilt Angle
56W maximum, Power management mode: 2W maximum*
506.0 × 404.0 × 210.0mm / 19.9 × 15.9 × 8.3" (W×H×D), 5.0kg / 11.0lbs
Up: 20 degrees, Down: 5 degrees
Operating: Temperature 5 to 35°C / 41 to 95°F
Environmental
Humidity
Storage: Temperature -20 to 60°C / -4 to 140°F
Humidity 5 to 85% (No condensation)
10 to 80% (No condensation)
Considerations
Approvals
TCO ’03, CE, TÜV-GS, TÜV-Ergonomics, FCC-B, UL/ C-UL, VCCI-B,
GOST-R, CCC
NOTE
* Condition: Audio equipment is not connected.
28 APPENDIX
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS: ProLite E2202WSV
LCD Panel Driving system
Size
a-Si TFT Active Matrix
Diagonal: 55cm / 22"
Pixel pitch
0.277mm H × 0.277mm V
300cd/m2 (Typical)
Brightness
Contrast ratio
1000 : 1 (Typical), 2000:1 (DCR)
Viewable angle Right / Left / Up / Down: 80 degrees each
Response time
Display Colors
5ms (Black, white, black)
Approx. 16.7 million maximum
Analog: Horizontal 24.0-80.0kHz, Vertical 55-75Hz
162MHz maximum
Sync Frequency
Dot Clock
Maximum Resolution
Input Connector
Plug & Play
1680 × 1050, 1.8 MegaPixels
D-Sub mini 15pin
VESA DDC2BTM
Separate sync: TTL, Positive or Negative
Input Sync Signal
Input Video Signal
Input Audio Connector
Input Audio Signal
Speakers
Analog: 0.7Vp-p (Standard), 75Ω, Positive
ø 3.5mm mini jack (Stereo)
0.7Vrms maximum
2.0W × 2 (Stereo speakers)
Maximum Screen Size
Power Source
464.9mm W × 290.6mm H / 18.3" W × 11.4" H
100-240VAC, 50/60Hz, 1.5A
Power Consumption
Dimensions / Net Weight
Tilt Angle
56W maximum, Power management mode: 2W maximum*
506.0 × 404.0 × 210.0mm / 19.9 × 15.9 × 8.3" (W×H×D), 5.0kg / 11.0lbs
Up: 20 degrees, Down: 5 degrees
Operating: Temperature 5 to 35°C / 41 to 95°F
Environmental
Humidity
Storage: Temperature -20 to 60°C / -4 to 140°F
Humidity 5 to 85% (No condensation)
10 to 80% (No condensation)
Considerations
Approvals
TCO ’03, CE, TÜV-GS, TÜV-Ergonomics, FCC-B, UL/ C-UL, VCCI-B,
GOST-R, CCC
NOTE
* Condition: Audio equipment is not connected.
APPENDIX 29
Download from Www.Somanuals.com. All Manuals Search And Download.
DIMENSIONS : ProLite E2201W
507.0mm/20.0"
475.5mm/18.7"
74.0mm/2.9"
260.0mm/10.2"
DIMENSIONS : ProLite E2202WS / E2202WSV
506.0mm/19.9"
467.0mm/18.4"
61.0mm/2.4"
204.0mm/8.0"
30 APPENDIX
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPLIANT TIMING
Horizontal
Frequency
31.469kHz
37.500kHz
37.861kHz
35.156kHz
37.879kHz
46.875kHz
48.077kHz
48.363kHz
56.476kHz
60.023kHz
47.776kHz
60.289kHz
67.500kHz
63.981kHz
79.976kHz
55.935kHz
70.635kHz
65.290kHz
31.469kHz
35.000kHz
49.725kHz
60.150kHz
24.827kHz
Vertical
Frequency
59.940Hz
75.000Hz
72.809Hz
56.250Hz
60.317Hz
75.000Hz
72.188Hz
60.004Hz
70.069Hz
75.029Hz
59.870Hz
74.893Hz
75.000Hz
60.020Hz
75.025Hz
59.887Hz
74.984Hz
60.000Hz
70.087Hz
66.667Hz
74.500Hz
74.720Hz
56.424Hz
Dot Clock
Video Mode
25.175MHz
31.500MHz
31.500MHz
36.000MHz
40.000MHz
49.500MHz
50.000MHz
65.000MHz
75.000MHz
78.750MHz
79.500MHz
102.250MHz
108.000MHz
108.000MHz
135.000MHz
106.500MHz
136.750MHz
146.250MHz
28.322MHz
30.240MHz
57.283MHz
80.000MHz
21.053MHz
VGA
SVGA
XGA
640 × 480
800 × 600
1024 × 768
VESA
WXGA 1280 × 768
1152 × 864
SXGA
1280 × 1024
WXGA+ 1440 × 900
WSXGA+ 1680 × 1050
720 × 400
*
*
*
*
*
VGA TEXT
Macintosh
PC9801
640 × 480
832 × 624
1024 × 768
640 × 400
NOTE
* DVI input is not compliant.
APPENDIX 31
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTOR PIN ASSIGNMENT
„ D-Sub mini 15pin
Pin
1
Input Signal
Red video
Pin
Input Signal
Connector
9
2
10 Ground
11
Green video
3
Blue video
Reserved port
Data line (SDA)*
13 H-Sync
12
4
Reserved port
Ground
5
6
Red video ground
Green video ground
Blue video ground
V-Sync
14
15
7
Clock line (SCL)*
* Compliant to VESA DDC.
8
„ DVI-D 24pin
Input Signal
Pin
1
Input Signal
T.M.D.S Data 2–
Pin
13
14
15
16
17
18
19
20
21
22
23
24
Connector
2
T.M.D.S Data 2+
1
9
8
16
24
3
T.M.D.S Data 2 Ground
Ground
17
4
Hot Plug Detect
T.M.D.S Data 0–
T.M.D.S Data 0+
T.M.D.S Data 0 Ground
DVI-D
5
6
Clock line (SCL) *
Data line (SDA) *
7
8
T.M.D.S Data 1–
9
10 T.M.D.S Data 1+
T.M.D.S Clock Ground
T.M.D.S Clock +
T.M.D.S Data 1 Ground
11
12
T.M.D.S Clock –
* Compliant to VESA DDC.
32 APPENDIX
M029A02
Download from Www.Somanuals.com. All Manuals Search And Download.
|