I W I L L DJ800
M o t h e r b o a r d
U s e r ’ s M a n u a l
FB25634000
Download from Www.Somanuals.com. All Manuals Search And Download.
P r e f a c e
Disclaimer
The manufacturer makes no representations or warranties regarding the
contents of this manual and specifically disclaims any implied warranties
of merchantability or fitness for any particular purpose. Furthermore, the
manufacturer reserves the right to revise this publication or make changes
in the specifications of the product described within it at any time without
notice and without obligation to notify any person of such revision or
change.
Trademarks
Microsoft and Windows are registered trademarks of Microsoft Corp.
Intel and Xeon are registered trademarks of Intel Corporation. Texas In-
struments are registered trademarks of Texas Instruments Corporation.
Other product names used in this manual are the properties of their respec-
tive owners and are acknowledged.
Copyright
This publication, including all photographs, illustrations and software,
is protected under international copyright laws, with all rights reserved.
Neither this manual, nor any of the material contained here in, may be
reproduced without the express written consent of the manufacturer. IWILL
©Copyright 2004
Important
The information in this document is subject to change without notice.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
U s e r ’ s M a n u a l
D J 8 0 0 M o t h e r b o a r d
T
a b l e
o
f
C
o n t e n t s
1: Overview .............................................................................1-1
Packing list................................................................................. 1-1
Safety Notice.............................................................................. 1-2
DJ800 Specification .................................................................. 1-5
2: Components and Jumper Setting.........................2-1
Mainboard Map .......................................................................... 2-1
Components List........................................................................ 2-2
Jumper Setting ........................................................................... 2-3
Rear Panel I/O Ports .................................................................. 2-6
Additional I/O Connectors ........................................................ 2-8
EPS12V Power Connectors ..................................................... 2-14
Primary IDE Connectors ......................................................... 2-15
CPU/ System Fan Connectors ................................................. 2-16
3: Hardware Installation .................................................3-1
Motherboard Installation .......................................................... 3-1
Memory Installation Procedure ................................................. 3-6
Recommended Memory Configurations ................................... 3-7
Installing Expansion Cards ........................................................ 3-8
Powering on your System.......................................................... 3-9
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
P r e f a c e
4: BIOS Setup.........................................................................4-1
Starting the BIOS Setup ............................................................ 4-1
Using the BIOS Setup Utility .................................................... 4-3
Main Menu................................................................................. 4-5
Advanced Menu ......................................................................... 4-6
Boot Menu ................................................................................. 4-7
Boot Setting Configuration Submenu ....................................... 4-8
Exit Menu ................................................................................ 4-10
5: OS and Drivers Installation.......................................5-1
OS Installation ........................................................................... 5-1
Drivers Installation .................................................................... 5-2
5:
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Overview
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
1
Package
DJ800 Motherboard
Three jumper caps (Extra caps in case original caps get lost)
One Power Installation CD (contains drivers and utilities)
DJ800 User’s manual
Rear panel I/O shield
Two sets of SATA cables
One ATA-66/100 IDE cable
One floppy disk drive cable
Two Hat Springs for CPU cooler
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
O
v
e
r v i e w
D J 8 0 0 M o t h e r b o a r d
YOU MUST HAVE ENOUGH SYSTEM INTEGRATION KNOWLEDGE
BEFORE THE INSTALLATION
General Safety Precautions
Keep the area around the Server clean and free of clutter.
Servers weigh a lot. When lifting the system, two people should
lift slowly from opposite ends with their feet spread out to distrib-
ute the weight. Always keep your back straight and lift with your
legs.
¡
¡
Place the chassis top cover and any system components that have
been removed away from the system or on a table so that they won’t
accidentally be stepped on.
¡
¡
¡
While working on the system, do not wear loose items such as neck-
ties and unbuttoned shirtsleeves. They can come into contact with
electrical circuits or get pulled into a cooling fan.
Remove any jewelry or metal objects from your body, which are
excellent metal conductors and can create short circuits and harm
you if they come into contact with printed circuit boards or areas
where power is present.
ESD Precautions
Electrostatic discharge (ESD) is generated by two objects with dif-
ferent electrical charges coming into contact with each other. An elec-
trical discharge is created to neutralize this difference, which can dam-
age electronic components and printed circuit boards. The following
measures are generally sufficient to neutralize this difference before
contact is made to protect your equipment from ESD:
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
1
Use a grounded wrist strap designed to prevent static discharge.
¡
¡
Keep all components and printed circuit boards (PCBs) in their
antistatic bags until ready for use.
Touch a grounded metal object before removing the board from
the antistatic bag.
¡
¡
Do not let components or PCBs come into contact with your
clothing, which may retain a charge even if you are wearing a wrist
strap.
Handle a board by its edges only; do not touch its components,
peripheral chips, memory modules or contacts.
When handling chips or modules, avoid touching their pins.
Put the motherboard and peripherals back into their antistatic bags
when not in use.
¡
¡
¡
For grounding purposes, make sure your computer chassis provides
excellent conductivity between the power supply, the case, the
mounting fasteners and the motherboard.
¡
¡
After accessing the inside of the system, close the system back up
and secure it to the rack unit with the retention screws after ensur-
ing that all connections have been made.
Operating Precautions
¡
¡
Check package contents
Missing or damaging accessories
Please contact your vendor immediately
Motherboard damage
¡
¡
Please contact your vendor immediately
Prepare minimum system components
z
z
z
z
z
Intel Xeon @800MHz FSB Processor
At least one Registered DDR2 memory module
Graphic card with PCI-Express interface
At least one SATA or IDE HDD
EPS12V Power Supply with 460W or above
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
O
v
e
r v i e w
D J 8 0 0 M o t h e r b o a r d
Getting Help
If a problem arises with your system during Installation or Operation,
you should first ask your dealer for help as they have most likely config-
ured your system. They generally have the best grasp of your issues and
the fastest response for your symptoms. If your dealer is near your location,
it is recommended that you first bring your system to them to have it ser-
viced instead of attempting to solve the problem yourself.
If those options don’t work for you, IWILL also provides some helpful
resources to help you.
product’s page which contain links to product updates such as Jumper
settings or BIOS updates.
2. The FAQ (Frequently Asked Questions) sections in the IWILL
website are often helpful since other users often have the same
questions.
tions within 5 business days.
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
1
DJ800 Specifications
ꢀ Intel® Dual Xeon Socket 604 CPUs
Processor
Chipset
ꢀ Supports 800MHz FSB
ꢀ Intel E7525 Chipset MCH
ꢀ Intel ICH5R
ꢀ Intel PXH
ꢀ Winbond 83627 HF
ꢀ 8 DIMMs for 240-pin DDR2 400 DIMM sockets
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Uses Registered DDR2 with ECC or Non-ECC memory
Supports total system memory size of up to 16GB
Intel 82541PI Gigabit Ethernet Controller
One RJ-45 connectors for GbE
Memory
On-Board
LAN
Support PME
ꢀ Integrated Analog Device AD1980
ꢀ Professional 6-channel Audio with S/PDIF out
ꢀ Support MIC IN/LINE OUT for the front panel
ꢀ AC ’97 CODEC
Audio
ꢀ 4 x external USB 2.0 ports
USB
ꢀ 4 x internal USB 2.0 ports
ꢀ TI TSB43AB22
ꢀ One pin header for front panel IEEE-1394 port
ꢀ One external IEEE-1394 header
IEEE-1394
ꢀ 2 Serial ATA ports supported by ICH5R with RAID 0, 1
ꢀ 4 Serial ATA ports supported by Adaptec 8110
ꢀ Support Adaptec Host RAID
Serial ATA
ꢀ Support hot swap
ꢀ One PCI Express x16 slot for graphics
ꢀ One PCI Express x4 slot
Expansion
Slots
ꢀ One PCI-X 64-bit/133 MHz
ꢀ Two PCI-X 64-bit/100 MHz
ꢀ One PCI 32-bit / 33 MHz
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
O
v
e
r v i e w
D J 8 0 0 M o t h e r b o a r d
z 34-pin Floppy Connector
4-pin CD-In and Aux-In audio input connector
Internal I/O
connector
z
z 2x 40-pin IDE connectors, supports up to
four (4) Enhanced IDE devices
IDE Bus
z Dual Channel Master Mode
z Ultra DMA 100/66/33
z PS/2 mouse and keyboard connectors
z 1 x UART 16550 serial port (COM1)
z
1 x 25-pin parallel port with ECP/EPP support
Rear Panel I/O
z 4 x on board USB 2.0 ports
z 1 x IEEE-1394 port
z 1 x S/PDIF Out
z Rear Out and Center Out
z
Audio Phone Jacks - Line Out, Mic In, Line-In.
z AMI BIOS
Flash write protection by BIOS and one jumper
z
System BIOS
z ACPI 1.1
z APM 1.2
z Support ACPI S1, S3
z Support ASF 2.0
z Hardware Monitor control by Winbond
W83627 HF
System Management
Form Factor
z Support AC power failure
z EATX form factor
z 12’’x13’’
z EEB 3.5
z EPS 12V power connectors (24 pin + 8 pin)
1-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
Components and Jumper Setting
Download from Www.Somanuals.com. All Manuals Search And Download.
ComponentsandJumper Setting
D J 8 0 0 M o t h e r b o a r d
MAINBOARD MAP
J57
J63
JP18
JP19
JP10
J46
J48
JP10A
J66
J67
J68
J69
J34
J34A
CPU2
CPU1
JP1
J43
Floppy
Primary
Secondary
JP16
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
2
Components List
CPU1; CPU2
Intel Xeon Socket604 Processor
Primary; Secondary IDE Driver Connectors
Floppy
Floppy Disk Driver Connector
PCI Slots
PCI-Express x16, x4 Slots; PCI-X 100,133; PCI
Memory Socket for DDR2 Memory
Clear CMOS Header
DIMM B4~A1
JP1
JP10 and JP10A
Memory Voltage Select Jumper
BIOS Flash Protect Jumper
USB Power Select Jumper
LAN Power Select Jumper
USB 2.0 Ports and Header
Front Panel Switch Header
WOL Connector
JP16
JP18
JP19
J34 &J34A
J43
J46
J48
SMBus Connector
J57
Front Audio Jumper
J63
IEEE 1394 (FireWire) Header
Serial ATA Connector
J66, J67, J68, J69
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
ComponentsandJumper Setting
D J 8 0 0 M o t h e r b o a r d
Jumper Setting
JP1: Clear CMOS Header
The onboard button cell battery powers the CMOS RAM. It con-
tains all the BIOS setup information. Keep the jumper connected to
pins 1-2 (Default) to retain the RTC data as shown below.
1-2
2-3
1
2
3
Normal (Default)
Clear CMOS
Under certain circumstances, you will need to reset system settings.
Follow these instructions to clear the CMOS RTC data:
1. Turn off the computer.
2. Short pins 2 and 3 with a jumper for a few seconds.
3. Replace the jumper to pins 1 and 2.
4. Turn on your computer by pressing the power-on button.
5. Hold down <F2> during boot and select either <Load Optimal
Defaults> or <Load Failsafe Defaults> in the “Exit” section. Then
go through the BIOS setup to re-enter user preferences.
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
2
JP10 and JP10A: Memory Voltage Select Jumper
This header lets you adjust the memory voltage.
JP10A JP10
VDDR
1.8V
JP10
1-2
JP10A
1-2
1.85V
1-2
2-3
1.9V
2-3
2-3
1-2
2-3
1.95V
JP16: BIOS Flash Protect Jumper
This jumper protects the system from unnecessary updating or flashing
of the BIOS. It secures the BIOS therefore prevents accidental overwriting
of the data stored in flash memory.
JP16
1-2
By Soft
Lock
1
2
3
2-3
Open
Unlock
JP18: USB Power Select Jumper
This header lets you set your USB headers power status. You can
choose power standby or not.
1-2
2-3
1
2
3
VCC5 Stand By
VCC5
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
ComponentsandJumper Setting
D J 8 0 0 M o t h e r b o a r d
JP19: LAN Power Select Jumper
This header lets you set your LAN connectors power status. You can
choose power standby or not.
1-2
2-3
1
2
3
VCC33 Stand By
VCC33
J57: Front Audio Jumper
This header lets you enable or disable the function of the front audio
connector.
9
1
W/O FRONT WITH FRONT
AUDIO AUDIO
CONNECTOR CONNECTOR
J57
5-6
SHORT
SHORT
OPEN
OPEN
10
9-10
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
2
Rear Panel I/O Ports
This is an illustration of the Mainboard rear I/O port array
Mouse
Parallel
LAN
IEEE1394
Line In
Line Out
Mic In
Keyboard
Rear Out Center Out S/PDIF
USB2.0
COM1
PS/2 Mouse Connector (6-pin Female)
The system will direct IRQ12 to the PS/2 mouse if one is detected.
If no mouse is detected, IRQ12 will be free for expansion cards to use.
PS/2 Keyboard Connector (6-pin Female)
This connection is for standard keyboards using a PS/2 (mini DIN)
plug. This connector will not accept standard AT size (large DIN) key-
board plugs. You may need a DIN to mini DIN adapter for standard AT
keyboards.
Universal Serial Bus Ports (4-pin Female)
Four onboard external USB 2.0 ports are available for connecting
USB devices. Refer to USB 2.0 Ports & Header for more information.
2-6
Download from Www.Somanuals.com. All Manuals Search And Download.
ComponentsandJumper Setting
D J 8 0 0 M o t h e r b o a r d
IEEE 1394/ FireWire Connector (6-pin Male)
You have one (1) onboard IEEE 1394 connector port for connecting
FireWire devices. Refer to IEEE 1394 Ports & Header for more
information.
Serial Port (COM1) Connector (9-pin Male)
The COM1 serial port can be used for pointing devices or other se-
rial devices. See BIOS for more on serial port setup.
Parallel Printer Connector (25-pin Female)
You can enable the parallel port and choose an IRQ through the BIOS.
You can choose between ECP and EPP support through the BIOS setup.
Onboard LAN Port (RJ-45)
This Mainboard uses Intel 82541PI Gigabit Ethernet Controller. Refer
to the Onboard LAN User Guide for further information.
Audio Jacks (Phone Jacks)
The interface is supported by the onboard Analog Device AD1980.
It has 3 phone jacks for Line-Out, Microphone In, and Line-In.
S/PDIF Port
DJ800 also provides the S/PDIF out, Rear Out, and Center Out
function.
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
2
Additional I/O Connectors
The Mainboard also contains connectors for adding additional ports
and devices to the Mainboard.
J43: Front Panel Switch Header
Reset Button
- HDD +
- ACPI +
-
SPEAKER
+
- Power LED +
Reset Button (2-pin RST)
This 2-pin connector connects to the chassis-mounted reset switch
for rebooting your computer without turning your power switch off and
on. This is a preferred method of rebooting your system to prolong the
life of your system’s power supply.
Hard Disk Activity LED (2-pin HDD_LED)
This connector supplies power to the chassis’s HDD/IDE activity
LED. Read and Write activity by devices connected to the Primary or
Secondary IDE connectors will cause the front panel LED to light up.
2-8
Download from Www.Somanuals.com. All Manuals Search And Download.
ComponentsandJumper Setting
D J 8 0 0 M o t h e r b o a r d
ACPI LED
ACPI function allows the system to enter or resume from the Sus-
pend mode. If your system chassis does not have this button, the same
function may be performed from your OS; if it is supported.
Power On Switch
This switch connects to the system’s Power button allowing you to
power on and off the system. You can configure the system to use the
keyboard or mouse to power-on the system. You can also configure the
system to respond to power restoration after a power outage occurs.
These functions can be configured by making appropriate settings in
the Integrated Peripherals submenu (“Super IO Device” field) of the
BIOS.
Speaker Connector
This connects to the PC speaker installed in the system chassis.
Power LED Connector
This connector connects to the system’s Power LED. When the
system’s power is on, this LED will light.
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
2
J46: WOL Connector
Function
This connector lets you attach a managed network adapter to the
motherboard via a Wake-on-LAN cable. When the system is off, the
managed network adapter uses an alternate power source to monitor
the network. If it receives a wake-up packet from the server the
system is remotely and automatically powered up.
J48: SMBus Connector
Function
The SMBus (System Management Bus) connector is used to con-
nect SMBus devices. It is a multiple device bus that allows multiple
chips to connect to the same bus and enable each one to act as a
master by initiating data transfer.
2-10
Download from Www.Somanuals.com. All Manuals Search And Download.
ComponentsandJumper Setting
D J 8 0 0 M o t h e r b o a r d
J63: IEEE 1394 (FireWire) Header
This Mainboard features an integrated Texas Instrument TSB43AB22
chip which supports two (2) IEEE 1394 (Firewire) ports. IEEE 1394
(FireWire) supports transfer rates of up to 400MB/s. One port is in-
stalled on the on-board I/O array, and a header is for external installation.
Pin Assignment
2
Pin 1 TPB0 Pin 2 TPB0-
Pin 3 GND Pin 5 GND
Pin 5 TPA0 Pin 6 TPA0-
1
10
Pin 7 PWR Pin 8 PWR
Pin 9 NC Pin 10 NC
2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
2
J66, J67, J68, J69 Serial ATA Connector
DJ800 supports up to 6 SATA devices each with data at transfer rates of
150MB/s. Two Serial ATA ports supported by ICH5R, and four Serial ATA
ports supported by Adaptec 8110. Adaptec 8110 also supports RAID
configurations. RAID stands for “Redundant Array of Independent De-
vices” and provides different levels of safety, redundancy and performance.
This chipset supports RAID 0, 1, and 10, which are defined as follows:
RAID Type
Description
RAID 0
Striping: high performance, designed to connect mul
tiple drives to act as one
RAID 1
Mirroring: writes data to two drives at once in case one
drive fails, the other one will be a complete replica and
can continue on. Full fail-over
RAID 10
Combination of RAID 0 and 1: over 4 drives, The drives
are split in half and striped together, and the 2 new st-
riped drives are then mirrored.
This Mainboard features six Serial ATA ports for six Serial ATA devices.
Serial ATA PIN Assignments
Pin
1
2
Description
GND
TXP
TXN
GND
RXN
RXP
3
4
5
6
7
Serial ATA Drive Conncetors
GND
2-12
Download from Www.Somanuals.com. All Manuals Search And Download.
ComponentsandJumper Setting
D J 8 0 0 M o t h e r b o a r d
J34 &J34A: USB 2.0 Ports and Header
DJ800 supports eight USB 2.0 ports. USB 2.0 supports transfer rates of
up to 480MB/s. Four ports show up on the on-board I/O array, and four
ports are internal.
Pin Assignment
Pin 1 VCC 5V
Pin 3 Data-
Pin 5 Data+
Pin 7 GND
Pin 9 NC
Pin 2 VCC 5V
Pin 5 Data-
Pin 6 Data+
Pin 8 GND
Pin 10 GND
1
2
10
CD In and AUX In Audio Inputs (4-pin)
There are both CD In and AUX In 4-pin connector to connect your
internal sound devices to the Sound Card.
4-pin Onboard Audio Header
Audio Pin Assignments
Description
Audio-L
Ground
Pin
1
1
2
Ground
3
Audio-R
4
2-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
2
EPS12V Power Connectors
There are two power connectors on the motherboard of the required
EPS 12V power supply. These are not standard ATX connectors. DJ800
needs a minimum 460-watt EPS 12V power supply that complies with
the Intel Xeon processor power supply design guidelines. Find the proper
orientation of the connectors and push down firmly to make sure that
the pins are aligned (the connector will only insert properly when prop-
erly aligned). The 8-pin connector is a dedicated power connector to
supply power for the CPUs.
8-pin PowerSupply
Connector(+12V)
24-pin PowerSupply
Connector
COM
+3.3V
+12V
+12V
5VSB
PWR_OK
COM
+5V
GND
GND
GND
GND
+12V
+12V
+12V
+12V
+5V
+5V
+5V
RESERVED
COM
COM
Power Connectors:
This are for the required
EPS 12V power supply
2X12 24-pin Connector
COM
COM
+5V
PS_ON
COM
COM
+3.3V
+3.3V
-12V
+3.3V
2X4 8-pin Connector
EPS 12V PSU Only
2-14
Download from Www.Somanuals.com. All Manuals Search And Download.
ComponentsandJumper Setting
D J 8 0 0 M o t h e r b o a r d
Primary IDE connectors
The two 40-pin IDE connectors (primary and secondary channels)
support 80-conductor IDE ribbon cables. Connect the single connector
end to the Mainboard. Then, connect the two connectors at the other
end to your IDE device(s). If you connect two hard disks to the same
cable, you must set the second drive as a Slave through its jumper
settings. Refer to the IDE device’s documentation for the specific jumper
settings. (Pin 20 is removed to prevent the connector from being in-
serted in the wrong orientation when using ribbon cables with pin 20
plugged in). The BIOS supports Ultra DMA 33/66/100.
IMPORTANT
Ribbon cables should always be connected with the red stripe on the
Pin 1 side of the connector. IDE ribbon cables must be less than 46 cm
(18 inches) long, with the second drive connector no more than 15 cm
(6 inches) away from the first connector.
Floppy Disk Drive Connector
This 34-pin connector supports the standard floppy disk drive rib-
bon cable. Connect the single connector end to the Mainboard. Then,
plug the other end of the ribbon into the floppy drive. Make sure you
align the Pin 1 on the connector with the Pin 1 alignments on the
Mainboard and the floppy drive.
2-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
2
CPU/ System Fan Connectors
There are five 3-pin fan connectors in the Mainboard. Two fans are
used for CPU1 and CPU2; three fans are for system and front. These
connectors support cooling fans of 500mA (6W) or less. Depending on
the fan manufacturer, the wiring and plug may be different. Connect the
fan’s plug to the Mainboard with respect to the polarity of the fan
connector.
3-pin Fan Connector
Sensor +12V
GND
WARNING
The CPU and/or motherboard will overheat if there is not enough
airflow across the CPU and onboard heatsink. Damage may occur to the
motherboard and/or the CPU fan if these pins are incorrectly used. These
are NOT jumpers; DO NOT place jumper caps over these pins.
2-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Hardware Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
3
Motherboard Installation
This section explains the basic requirements for installing the
motherboard in a system housing or “chassis”. Since housing designs vary
widely, you will need to consult the housing documentation for specific
information.
To install the motherboard in a system housing, you will need to do the
following:
Install a rear panel I/O shield
¡
¡
¡
¡
Attach the board to the housing
Connect leads from the housing’s front panel
Connect other internal system components.
Motherboard Installation Procedure
The motherboard requires installing the supplied CPU Backplates to
mount the heat sink retention mechanisms. Refer to the CPU Installation
section in this chapter for details.
If the housing you are using normally stands vertically, place the open
housing on its side before you start.
To install the motherboard, please follow the steps below.
1. Review any instructions that came with the system housing and pre-
pare the necessary mounting hardware that came with it.
2. Identify the mounting holes on the motherboard and confirm that the
housing has standoffs that match them.
3. Install the rear panel I/O shield in the housing’s I/O panel opening.
4. Place the motherboard in the housing and align the mounting holes
to the standoffs of the housing’s motherboard mounting plate. Make
sure all of the rear I/O ports are properly aligned with the openings
of the I/O panel.
5. Secure the motherboard to the housing by inserting mounting screws
in all the holes.
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
D J 8 0 0 M o t h e r b o a r d
IWILL DJ800 support Intel Xeon @FSB800 MHz processor. We only
recommend using the Intel Original heatsink kit. CEK (Common Enabling
Kit) is specially designed for the Intel latest Xeon. For installing CEK,
please follow direction as below.
Installing the CPU and Heatsink Procedures
Step 1— Before you install the heatsink, please check whether the attached
Hat Springs fasten well to the back of this motherboard or not.
Step 2— Raise the retaining lever of the processor locking mechanism to a
perpendicular position.
Raise the socket
lever to the vert-
Raise the retaining
lever
ical position
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
3
Step 3— Align the processor to the socket by matching the Pin 1 corner of the
socket (marked with a triangle) to the Pin 1 corner on the Socket 604
(marked by a triangular hole in the Pin 1 corner).
Align the Pin 1 corners
Step 4— Carefully insert the Xeon processor in the socket receptacles, taking
care not to bend any pins.
Insert the processor
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
D J 8 0 0 M o t h e r b o a r d
Step 5— Lower the locking mechanism’s retaining lever and secure it in place
to secure the processor in the socket. Grasp the processor by the
edges and gently pull upwards to insure it is properly inserted. The
processor shouldn’t move.
Secure the CPU re-
taining lever
Step 6—Apply all of the TIM in the applicator to the center of the square heat
spreader plate in the middle of the CPU. Do not spread the TIM around.
When you place the heatsink on top of the CPU the material will
disperse evenly.
Apply all of the ther-
mal interface mate-
rial to the center of
the processor heater
spreader plate
Important
When you only place ONE Intel Xeon processor, please put on the
position of CPU1.
3-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
3
Step 7— Fasten the motherboard on the chassis first. Then, place the CPU
HeatSink on the top, and match the heatsink, spring and motherboard
holes. Finally, please gently drive in these screws in order to fasten the
heatsink.
Notice: If you use the third party heaksink, it would possibly not fit
our Spring installation method. Please contact with your vendor for the
further information, and also check on IWILL website.
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
D J 8 0 0 M o t h e r b o a r d
Memory Installation Procedure
Installing Memory
This Mainboard uses Registered DDR2 Memory with ECC or Non-
ECC only. Please be aware of the difference between DDR and DDR2.
DDR modules will NOT compatible with DDR2 slots. Don’t plug DDR
modules into DJ800 memory slots.
IMPORTANT
* Before buying DDR2 (Double Data Rate 2) DIMMs for use with the
Mainboard, it is recommended that you consult your local reseller
for the best and most compatible memory to use.
* This Mainboard only supports Registered DDR2 compliant modules.
* To ensure compatibility, only use DIMM pairs of the same exact
type and size and made by the same company.
One DDR2 Module
Two DDR2 Modules
Four DDR2 Modules
Six DDR2 Modules
Eight DDR2 Modules
DIMM B4 (1)
DIMM B4, A4
DIMM B4, A4; B3, A3
B4, A4; B3, A3; B2, A2
B4, A4; B3, A3; B2, A2;
B1, A1
(1) We strongly recommend that you always install a
pair of DDR2 memory in order to take the full advan-
tage of dual channel.
3-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
3
Recommended Memory Configurations
The following steps are our recommended DIMM installation path
based on the number of DIMMS being installed (Remember to check
that the DIMMS are 1.8V Registered ECC or Non-ECC DDR2 DIMMs)
Memory Installation Procedures
1. Locate the Memory Bank on the Mainboard, where you will be in-
stalling the DIMMs.
2. Make sure the DIMM’s pins are facing down, and check that the pin
arrangement on the memory module resembles the one pictured
below.
3. Insert the module into the DIMM socket and press down evenly on
both ends firmly until the DIMM module is securely in place. (The
tabs of the DIMM socket will close-up to hold the DIMM in place
when the DIMM is properly installed on the socket’s bottom.)
Module retaining notches
Socket retaining notches
4. Repeat step 1 to step 3 for all additional DIMM modules.
P.S If you only install one DIMM, please install on DIMMB4.
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
D J 8 0 0 M o t h e r b o a r d
Installing Expansion Cards
1. Remove the bracket plate on the slot you intend to use. Keep the
bracket for possible future use.
2. Insert the PCI card into the correct slot on the Mainboard, pushing
down with your thumbs evenly on both sides of the card.
3. Secure the card on the slot with the screw you removed above.
4. Assign IRQs for PCI expansion card: An IRQ number is automati-
cally assigned to PCI expansion card. In the PCI bus design, the BIOS
automatically assigns an IRQ to a PCI slot that contains a card re-
quiring an IRQ.
WARNING
Please completely power OFF your power supply when adding or
removing any expansion cards or other system components. Failure to
do so may cause severe damage to both your Mainboard and expansion
cards.
IMPORTANT
DJ800 provides a PCI-Express x16 slot for graphic use. It provides
the higher performance and greater bandwidth. DJ800 does not support
AGP slot, so please choose the graphic card with PCI-Express interface.
3-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
3
Powering on your System
Follow these instructions to power on the computer after you have
installed the Mainboard and all system devices.
1. Be sure that all switches are off (in some systems, Off is marked by
“O”).
2. After double-checking all jumper settings and connections, close the
system chassis cover.
3. Connect the power cord to the power cord connector located on the
power supply at the back of your system chassis and plug the power
cord into a power outlet that is equipped with a surge protector.
4. Turn on your devices in the following order:
Monitor
¡
¡
System power
For power supplies, you need to switch On the power supply, then
press the:
1. Power switch on the front of the chassis the first time you start up
the system.
2. The power LED on the front panel of the system case will light up.
For power supplies, the system LED will light up when the power
switch is pressed. The monitor LED may light up after the system’s
LED if it complies with “Green” standards or if it has a power standby
feature. The system will first run its “power-on” tests. While the
tests are running, additional messages will appear on the screen. If
you do not see anything on the screen within 30 seconds from the
time you turn on the power, the system may have failed a power-on
test. Re-check your jumper settings and connections. Contact your
retailer/dealer for assistance if everything else fails.
3. During power-on, hold down <F2> to enter BIOS setup. Follow the
instructions in BIOS for further setup information.
3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
BIOS Setup
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
4
BIOS Setup
This chapter discusses the AMIBIOS Setup program built into the ROM
BIOS. The Setup program allows users to modify the basic system
configuration.
The BIOS is the Basic Input / Output System used in all IBM PC, XT,
AT, and PS/2 compatible computers. The AMIBIOS flash chip stores the
system parameters, such as type of disk drives, video displays, etc. in the
CMOS. When the computer is turned off, a back-up battery provides power
to the BIOS flash chip, enabling it to retain system parameters. Each time
the computer is powered-on the computer is configured with the values
stored in the BIOS ROM by the system BIOS, which gains control at boot-
up.
The AMIBIOS installed in your computer system’s ROM (Read Only
Memory) is a custom version of an industry standard BIOS. The BIOS
provides critical low-level support for standard devices such as disk drives
and serial and parallel ports.
Starting the BIOS Setup
The AMIBIOS is immediately activated every time you power on
the system. The BIOS reads the system information contained in the
CMOS and begins the process of checking the system and configuring
it. After configuring the system, the BIOS will follow the Boot Order to
seek out an operating system. The BIOS then turns control of the sys-
tem over to the operating system.
The CMOS information that determines the system parameters may
be changed by entering the BIOS Setup utility.
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
B I O S S e t u p
D J800 M o t h e r b o a r d
1. Power on the System.
Note: Normally, the only visible POST (Power On Self Test) routine
is the memory test.
2. As the memory is being tested, you can access the BIOS Setup Util-
ity by pressing the <F2> key when “Press < F2> to enter SETUP”
appears briefly at the bottom of the screen.
From the main menu of the BIOS Setup Utility, you can access the
other setup screens, such as the Security and Power menus.
4-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
4
Using the BIOS Setup Utility
Navigating through the BIOS Setup Utility is straightforward. Use
the arrow keys to highlight items, press <Enter> to select items in menus,
and press <Esc> to quit. The following table provides more details about
how to navigate in the Setup program using the keyboard.
Up Arrow Key
Down Arrow Key Move to the next item
Left Arrow Key Move to the previous menu
Right Arrow Key Move to the next menu
Move to the previous item
<Esc> key
In the Submenu: Exit the submenu.
In the BIOS main menu: Jump to the Exit Menu
Select the highlighted item. When available, a
pop-up list will display for you to select the item
value or select a submenu
<Enter> Key
<PgUp> Key
<PgDn> Key
Previous page on Scrollable menus or Jump to
the first interactive item listed
Next page on Scrollable menus or Jump to the
last interactive item listed
<F1> Key
<F2>/<F3> Key
<F7> Key
<F8> Key
<F9> Key
<F10> Key
Home
General Help on Setup navigation keys.
Change Colors
Discard Changes
Load Failsafe Defaults
Load Optimal Defaults
Save and Exit
Go to Top of Screen
END
Go to Bottom of Screen
ESC
Exit
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
B I O S S e t u p
D J800 M o t h e r b o a r d
IMPORTANT
The BIOS does NOT automatically save values that you have
modified. If you do not save your values before you exit the BIOS Setup
Utility, all your changes will be lost.
If after making and saving system changes with the BIOS Setup
Utility, you discover that your computer is no longer able to boot, the
AMIBIOS supports an override, which will reset your system to the
Failsafe defaults. If that fails, it is possible to manually clear the present
CMOS information through the “Clear CMOS Header” on the
motherboard (Refer to Jumper Settings for more information).
The best advice is to ONLY alter settings that you thoroughly
understand. The default settings have been carefully chosen by
AMIBIOS to provide the maximum system performance and reliability.
Even a slight change to the chipset setup may cause potential and un-
predictable failure to the system.
4-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
4
Main Menu
This is the first screen that is displayed when you enter the BIOS
Setup Utility. Each tab lined on the top of the screen represents each
different menu. The following picture shows the main menu. Main menu
shows the information of BIOS version, date and ID, processor type,
speed and count, and system size. In addition, system time and date is
adjustable using + / - key or number keys.
IMPORTANT
Due to the different BIOS versions, this BIOS screen will possibly
be not exactly the same with what you see while you are setting up
DJ800 BIOS. Please read the right description column carefully on your
BIOS screen. For any further setup questions, please contact with our
Technology Support staff.
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
B I O S S e t u p
D J800 M o t h e r b o a r d
Advanced Menu
You can make these modifications on the Advanced Menu. Select
the Submenus to modify those settings.
CPU Configuration
¡
¡
¡
¡
¡
¡
¡
¡
¡
¡
¡
¡
IDE Configuration
Floppy Configuration
SuperIO Configuration
Hardware Health Configuration
ACPI Configuration
Event Log Configuration
MPS Configuration
PCI-Express Configuration
Remote Access Configuration
USB Configuration
Onboard Device Configuration
4-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
4
Boot Menu
Feature
Description
Boot Device Priority
Hard Disk Drives
Specify the boot device priority sequence
Specify the boot device priority sequence
from available hard drives
Removable Drives
CD/DVDDrives
Specify the boot device priority sequence
from available removable drives
Specify the boot device priority sequence
from available CD/DVD drives
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
B I O S S e t u p
D J800 M o t h e r b o a r d
Boot Setting Configuration Submenu
Feature
Option
Description
Quick Boot
Disabled
Enabled
Allows BIOS to skip
tests while booting
Quiet Boot
Disabled: display normal
POST messages Enabled:
display OEM logo
Disabled
Enabled
Set display mode for
option ROM
AddOn ROM
Display Mode
Force BIOS
Keep Current
Select power on state
for NumLock
Bootup Num-Lock
PS/2 Mouse Support
Typematic Rate
Off
On
Disabled
Enabled
Select support for PS/
2 mouse
Slow
Fast
S e l e c t k e y b o a r d
typematic rate
4-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
4
Wait for “F1” if error
Disabled
Enabled
Wait for F1 key to be
pressed if error occurs
Hit ‘DEL’ Message
Display
Display “PressDEL to run
Setup” in POST
Disabled
Enabled
Disabled
Enabled
Enabled: allows option
ROMs to trap interrupt 19
Interrupt 19 Capture
4-9
Download from Www.Somanuals.com. All Manuals Search And Download.
B I O S S e t u p
D J800 M o t h e r b o a r d
Exit Menu
Feature
Description
Exit system setup after saving the
changes.
Save Changes and Exit
F10 key can be used for this operation
Exit system setup without saving the
changes. ESC key can be used for this
operation
Discard Changes and Exit
Discard Changes
Discard changes done so far to any of
the setup questions. F7 key can be used
for this operation
Load optimal default values for all the
setup questions. F9 key can be used for
this operation
Load Optimal Defaults
Load Failsafe Defaults
Load Failsafe default values for all the
setup questions. F8 key can be used
for this operation
4-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5
OS and Drivers Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
OS and Drivers Installation
D J800 M o t h e r b o a r d
OS Installation
DJ800 can be run on Windows 2000, XP, and Linux (SuSe64, RedHat)
system.
DJ800 supports the Intel Extended Memory 64 bit Technology. It can
take the full advantage of 64 bit architecture. In order to run full advantage
of 64 bit, you should install OS with 64 bit architecture.
For the 64 bit OS information, you can go to the below website to find
out more information.
Contact Microsoft for additional details.
¡
¡
¡
Contact Red Hat for additional details.
Contact SuSE for additional details.
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
5
Drivers Installation
On the motherboard package, you could find a Power installation CD.
It contains the required drivers.
1. Audio Driver
The audio driver for on board AD1980 chipset
2. Adaptec 8110 driver for the serial-ATA devices
3. Intel GbE LAN Driver
4. INF Driver
5. USB 2.0 Driver (for Windows 2000)
Inside the CD, you can also find the free software “Acrobat Reader” to
help you read our pdf.file. Besides, this user’s manual will also be placed
inside this the CD-ROM.
If you have any question about how to install operation system, please
Supporters. We also suggest you visit our website for downloading the
latest BIOS and drivers regularly.
5-2
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
Download from Www.Somanuals.com. All Manuals Search And Download.
|