Husqvarna Lawn Mower YTH2248 User Manual
01960_husqvarna  
02777  
YTH2248  
Owner's Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY RULES  
Safe Operation Practices for Ride-On Mowers  
•
•
•
•
•
Be sure the area is clear of other people before mowing.Stop  
7!2.).'ꢀ )N ORDER TO PREVENT ACCIꢁ  
DENTAL STARTING WHEN SETTING UPꢂ TRANSꢁ  
PORTINGꢂ ADJUSTING OR MAKING REPAIRSꢂ  
ALWAYS DISCONNECT SPARK PLUG WIRE  
AND PLACE WIRE WHERE IT CANNOT CONTACT  
SPARK PLUGꢃ  
machine if anyone enters the area.  
Never carry passengers or children even with the blades  
off.  
Do not mow in reverse unless absolutely necessary. Always  
look down and behind before and while backing.  
Nevercarrychildren.Theymayfalloffandbeseriouslyinjured  
or interfere with safe machine operation.  
Keep children out of the mowing area and under the watchful  
care of another responsible adult.  
7!2.).'ꢀ $O NOT COAST DOWN A HILL  
IN NEUTRALꢂ YOU MAY LOSE CONTROL OF THE  
TRACTORꢃ  
•
•
Be alert and turn machine off if children enter the area.  
Before and when backing, look behind and down for small  
children.  
7!2.).'ꢀ 4OW ONLY THE ATTACHMENTS  
THAT ARE RECOMMENDED BY AND COMPLY  
WITHSPECIlCATIONSOFTHEMANUFACTURER  
OF YOUR TRACTORꢃ 5SE COMMON SENSE  
WHEN TOWINGꢃ /PERATE ONLY AT THE LOWꢁ  
EST POSSIBLE SPEED WHEN ON A SLOPEꢃ  
4OO HEAVY OF A LOADꢂ WHILE ON A SLOPEꢂ  
IS DANGEROUSꢃ 4IRES CAN LOSE TRACTION  
WITH THE GROUND AND CAUSE YOU TO LOSE  
CONTROL OF YOUR TRACTORꢃ  
•
•
•
Mow up and down slopes (15° Max), not across.  
Remove obstacles such as rocks, tree limbs, etc.  
Watchforholes,ruts,orbumps.Uneventerraincouldoverturn  
the machine. Tall grass can hide obstacles.  
Use slow speed. Choose a low gear so that you will not have  
to stop or shift while on the slope.  
Avoid starting or stopping on a slope. If tires lose traction,  
disengage the blades and proceed slowly straight down the  
slope.  
If machine stops while going uphill, disengage blades, shift  
into reverse and back down slowly.  
Donotturnonslopesunlessnecessary, andthen, turnslowly  
and gradually downhill, if possible.  
•
•
•
•
7!2.).'  
%NGINE EXHAUSTꢂ SOME OF ITS CONSTITUENTSꢂ AND CERꢁ  
TAIN VEHICLE COMPONENTS CONTAIN OR EMIT CHEMICALS  
KNOWNTOTHE3TATEOF#ALIFORNIATOCAUSECANCERAND  
BIRTH DEFECTS OR OTHER REPRODUCTIVE HARMꢃ  
7!2.).'  
"ATTERY POSTSꢂ TERMINALS AND RELATED ACCESSORIES  
CONTAINLEADANDLEADCOMPOUNDSꢂCHEMICALSKNOWN  
TO THE 3TATE OF #ALIFORNIA TO CAUSE CANCER AND BIRTH  
DEFECTS OR OTHER REPRODUCTIVE HARMꢃ 7ASH HANDS  
AFTER HANDLINGꢃ  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
PRODUCT SPECIFICATIONS  
CUSTOMER RESPONSIBILITIES  
Gasoline Capacity  
and type:  
4 Gallons  
•
•
Read and observe the safety rules.  
Unleaded Regular  
Follow a regular schedule in maintaining, caring for  
and using your tractor.  
Oil Type (API-SF-SJ):  
SAE 10W30 (above 32°F)  
SAE 5W-30 (below 32°F)  
•
Follow the instructions under“Maintenance”and“Stor-  
age” sections of this owner’s manual.  
Oil Capacity:  
W/ Filter:  
W/O Filter:  
4.0 Pints  
3.5 Pints  
Spark Plug:  
(Gap: .030")  
Champion RC12YC  
WARNING: This tractor is equipped with an internal com-  
bustion engine and should not be used on or near any  
unimprovedforest-covered,brush-coveredorgrass-covered  
land unless the engine’s exhaust system is equipped with  
a spark arrester meeting applicable local or state laws (if  
any). If a spark arrester is used, it should be maintained  
in effective working order by the operator.  
Ground Speed (MPH):  
Forward:  
Reverse:  
0 – 5.5  
0 – 2.4  
Tire Pressure:  
Front:  
Rear:  
14 PSI  
10 PSI  
Charging System:  
Battery:  
15 AMPS @ 3600 RPM  
AMP/HR:  
MIN. CCA:  
Case Size:  
35  
280  
U1R  
In the state of California the above is required by law  
(Section 4442 of the California Public Resources Code).  
Other states may have similar laws. Federal laws apply on  
federal lands.  
Blade Bolt Torque:  
45-55FT. LBS.  
CONGRATULATIONS on your purchase of a new tractor.  
Ithasbeendesigned,engineeredandmanufacturedtogive  
you the best possible dependability and performance.  
A spark arrester for the muffler is available through your  
nearestauthorizedservicecenter/department (SeeREPAIR  
PARTS section of this manual).  
Shouldyouexperienceanyproblemyoucannoteasilyrem-  
edy, please contact your nearest authorized servicecenter/  
department We have competent, well-trained technicians  
and the proper tools to service or repair this tractor.  
Please read and retain this manual. The instructions will  
enable you to assemble and maintain your tractor properly.  
Always observe the “SAFETY RULES”.  
TABLE OF CONTENTS  
SAFETY RULES .........................................................2-3  
PRODUCT SPECIFICATIONS....................................... 4  
CUSTOMER RESPONSIBILITIES................................. 4  
ASSEMBLY.................................................................6-9  
OPERATION ...........................................................10-15  
MAINTENANCE SCHEDULE ...................................... 16  
MAINTENANCE .....................................................16-19  
SERVICE AND ADJUSTMENTS ............................20-26  
STORAGE.................................................................... 27  
TROUBLESHOOTING ............................................28-29  
REPAIR PARTS - TRACTOR ..................................32-45  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
UNASSEMBLED PARTS  
Steering Wheel  
Mower  
(2)Flanged  
Pins  
(1)Front Plate  
Assembly  
(2) Retainer Springs  
(single loop)  
(5) Retainer Springs  
(double loop)  
Steering  
Wheel  
Adapter  
Gauge Wheels  
(4) Adjusting Bars  
(4) Shoulder Bolts  
(4) Wheels  
Steering  
Wheel Insert  
(4) Locknuts 3/8-16  
(4) Retainer Springs  
(double loop)  
(4) Washers  
3/8 x 3/4 x 14 Ga.  
(4) Clevis Pins  
Seat  
Nose Roller  
Rod  
Nose Roller  
(2) Hex Bolts  
5/16 x 18 x 1  
(2) Locknuts  
5/16 x 18  
Nose  
Roller  
Brackets  
(1) Washer  
17/32 x 1-3/16 x 12 Gauge  
Retainer Spring  
Slope Sheet  
Keys  
(1) Knob  
(2) Keys  
(1) Oil Drain Tube  
For Future Use  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes.  
To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use  
the correct tools as necessary to insure proper tightness.  
TOOLS REQUIRED FOR ASSEMBLY  
STEERING  
WHEEL INSERT  
A socket wrench set will make assembly easier. Standard  
wrench sizes are listed.  
(1) Tire pressure gauge  
1/2 HEX NUT  
(2) 3/4" wrenches  
(2) 7/16" wrenches  
(1) Pliers  
(1) Utility knife  
(1) 3/4" socket w/drive ratchet  
LARGE FLAT  
WASHER  
Whenrightorlefthandismentionedinthismanual,itmeans  
when you are in the operating position (seated behind the  
steering wheel).  
STEERING  
WHEEL  
TO REMOVE TRACTOR FROM  
CARTON  
UNPACK CARTON  
ADAPTER  
•
Remove all accessible loose parts and parts cartons  
from carton.  
•
Cut along dotted lines on all four panels of carton.  
Remove end panels and lay side panels flat.  
Remove mower and packing materials.  
Check for any additional loose parts or cartons and  
remove.  
•
•
STEERING  
SHAFT  
BEFORE REMOVING TRACTOR FROM  
SKID  
71  
27  
ATTACH STEERING WHEEL (See Fig. 1)  
•
•
•
•
Remove locknut and large flat washer from steering  
shaft.  
Position front wheels of the tractor so they are pointing  
straight forward.  
Position steering wheel so cross bars are horizontal  
(left to right) and slide onto steering wheel adapter.  
Secure steering wheel to steering shaft with locknut  
and large flat washer previously removed. Tighten  
securely.  
Snap steering wheel insert into center of steering  
wheel.  
Remove protective materials from tractor hood and  
grill.  
FIG. 1  
HOW TO SET UPYOUR TRACTOR  
CHECK BATTERY (See Fig. 2)  
•
•
Lift hood to raised position.  
If this battery is put into service after month and year  
indicated on label (label located between terminals)  
charge battery for minimum of one hour at 6-10 amps.  
(See"BATTERY"inMaintenancesectionofthismanual  
for charging instructions).  
•
•
IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN  
SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO  
ROLL OFF SKID.  
LABEL  
FIG. 2  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
INSTALL SEAT (See Fig. 3)  
Adjust seat before tightening adjustment knob.  
TO DRIVE TRACTOR OFF SKID (See Op-  
eration section for location and function of  
controls)  
•
Remove adjustment knob and flat washer securing  
seat to cardboard packing and set aside for assembly  
of seat to tractor.  
WARNING:Beforestarting,read,understandandfollow  
all instructions in the Operation section of this manual. Be  
sure tractor is in a well-ventilated area. Be sure the area in  
front of tractor is clear of other people and objects.  
•
•
•
•
Pivotseatupwardandremovefromthecardboardpack-  
ing. Remove the cardboard packing and discard.  
Place seat on seat pan so head of shoulder bolt is  
positioned over large slotted hole in pan.  
Push down on seat to engage shoulder bolt in slot and  
pull seat towards rear of tractor.  
Pivot seat and pan forward and assemble adjustment  
knob and flat washer loosely. Do not tighten.  
•
Be sure all the above assembly steps have been com-  
pleted.  
•
•
Check engine oil level and fill fuel tank with gasoline.  
Place freewheel control in "transmission engaged"  
position (see "TO TRANSPORT" in Operation section  
of this manual).  
•
Sit on seat in operating position, depress clutch/brake  
pedal and set the parking brake.  
•
•
Lower seat into operating position and sit on seat.  
Slide seat until a comfortable position is reached  
which allows you to press clutch/brake pedal all the  
way down.  
•
•
Place motion control lever in neutral (N) position.  
Press lift lever plunger and raise attachment lift lever  
to its highest position.  
•
•
Get off seat without moving its adjusted position.  
Raise seat and tighten adjustment knob securely.  
•
Starttheengine.Afterenginehasstarted,movethrottle  
control to idle position.  
•
•
Release parking brake.  
Slowlymovethemotioncontrolleverforwardandslowly  
drive tractor off skid.  
SEAT  
SHOULDER  
BOLT  
•
•
Apply brake to stop tractor, setparkingbrakeandplace  
motion control lever in neutral position.  
Turn ignition key to "STOP" position.  
SEAT PAN  
Continue with the instructions that follow.  
TO ATTACH NOSE ROLLER (See Fig. 4)  
•
Assemble brackets "A" and "B" to the inside of mower  
mounting brackets as shown. Tighten securely.  
NOTE: Be sure bracket tabs are positioned in tab holes  
in mower brackets.  
•
Position nose roller between brackets and install rod  
and retainer spring.  
HEX  
ROD  
LOCK  
NUT  
BOLT  
FLAT WASHER  
"B"  
BRACKET  
02464  
ADJUSTMENT  
KNOB  
TAB  
HOLE  
FIG. 3  
NOSE  
ROLLER  
RETAINER  
SPRING  
NOTE: You may now roll or drive your tractor off the skid.  
Follow the appropriate instruction below to remove the  
tractor from the skid.  
"A" BRACKET  
FIG. 4  
TO ROLL TRACTOR OFF SKID (See Op-  
eration section for location and function of  
controls)  
ASSEMBLE GAUGE WHEELS TO MOWER  
DECK (See Fig. 5)  
The gauge wheels are designed to keep the mower deck  
in proper position when operating mower. Be sure they  
are properly adjusted to ensure optimum mower perfor-  
mance.  
•
•
•
Press lift lever plunger and raise attachment lift lever  
to its highest position.  
Release parking brake by depressing clutch/brake  
pedal.  
Place freewheel control in "transmission disengaged  
position" (See “TO TRANSPORT” in the Operation  
section of this manual).  
•
Slide gauge wheel bar down into bracket channel, Be  
sure that gauge wheel bar aligning holes are on top.  
Assemblegaugewheelsasshownusingshoulderbolts,  
3/8 washers and 3/8-16 center locknuts and tighten  
securely.  
•
Roll tractor forward off skid.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
•
•
For ease of mower to tractor assembly, raise gauge  
IMPORTANT: Check belt for proper routing in all mower  
wheels to highest position and retain with clevis pins  
and spring retainers.  
Adjust gauge wheels before operating mower.See“TO  
ADJUST GAUGE WHEELS” in the Operation section  
of this manual.  
pulley grooves.  
•
If equipped, turn height adjustment knob counter-  
clockwise until it stops.  
•
•
•
Lower mower linkage with attachment lift control.  
Install belt into electric clutch pulley groove.  
RETAINER SPRING  
Place the suspension arms on outward pointing deck  
pins. Retain with double loop retainer spring with loops  
up as shown.  
PIN  
•
•
Install front plate assembly to tractor suspension  
brackets and retain with single loop retainer springs  
as shown.  
Position front plate assembly between front mower  
brackets.Raise deck and plate assembly to align holes  
and insert flanged pins. Secure pins with double loop  
retainer springs between the plate and mower brack-  
ets.  
ADJUSTING  
BAR  
SHOULDER  
BOLT  
GAUGE  
WHEEL  
3/8-16 CENTER  
LOCKNUT  
3/8 WASHER  
NOTE: To assist in locating hole in flanged pin, the hole in  
pin is inline with notch on head of pin. If necessary, move  
mowerside-to-sidetogivespacebetweenplateandmower  
brackets.  
FIG. 5  
INSTALL MOWER  
(See Figs. 6 and 7)  
AND DRIVE BELT  
IMPORTANT: Check belt for proper routing in all mower  
pulley grooves.  
Be sure tractor is on level surface and mower suspension  
arms are raised with attachment lift control. Engage park-  
ing brake.  
•
•
Connect anti-sway bar to chassis bracket under left  
footrest and retain with double loop retainer spring.  
If equipped, turn height adjustment knob clockwise to  
remove slack from mower suspension.  
•
Cut and remove ties securing anti-sway bar and belts.  
Swing anti-sway bar to left side of mower deck.  
Slide mower under tractor with deflector shield to right  
side of tractor.  
•
•
Raise deck to highest position.  
Adjustgaugewheelsbeforeoperatingmowerasshown  
in the Operation section of this manual.  
•
FRONT SUSPENSION  
ELECTRIC  
BRACKETS  
CLUTCH PULLEY  
FRONT  
PLATE  
CHASSIS  
BRACKET  
FRONT  
MOWER  
BRACKET  
DOUBLE LOOP  
ASSEMBLY  
RETAINER  
SPRING  
GAUGE  
WHEEL  
SINGLE  
LOOP  
RETAINER  
SPRINGS  
FLANGED PIN  
DOUBLE LOOP  
RETAINER SPRING  
ANTI-SWAY  
BAR  
DEFLECTOR  
SHIELD  
USE PLIERS FOR  
RETAINER SPRINGS  
SUSPENSION  
ARMS  
DOUBLE LOOP RETAINER  
SPRING (OUTWARD POINTING  
DECK PINS)  
LOOP UP  
FIG. 6  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
✓CHECKLIST  
CHECK TIRE PRESSURE  
BEFOREYOUOPERATEANDENJOYYOURNEW TRAC-  
TOR, WE WISH TO ASSURE THAT YOU RECEIVE THE  
BESTPERFORMANCEANDSATISFACTIONFROMTHIS  
QUALITY PRODUCT.  
The tires on your tractor were overinflated at the factory  
for shipping purposes. Correct tire pressure is important  
for best cutting performance.  
•
Reduce tire pressure to PSI shown in “PRODUCT  
SPECIFICATIONS” section of this manual.  
PLEASE REVIEW THE FOLLOWING CHECKLIST:  
✓
✓
✓
All assembly instructions have been completed.  
No remaining loose parts in carton.  
Battery is properly prepared and charged. (Minimum  
1 hour at 6 amps).  
Seat is adjusted comfortably and tightened securely.  
All tires are properly inflated. (For shipping purposes,  
the tires were overinflated at the factory).  
Be sure mower deck is properly leveled side-to-side/  
front-to-rear for best cutting results. (Tires must be  
properly inflated for leveling).  
Check mower and drive belts. Be sure they are routed  
properly around pulleys and inside all belt keepers.  
Check wiring. See that all connections are still secure  
and wires are properly clamped.  
CHECK MOWER LEVELNESS  
For best cutting results, mower should be properly leveled.  
See “TO LEVEL MOWER HOUSING” in the Service and  
Adjustments section of this manual.  
✓
✓
CHECK FOR PROPER POSITION OF ALL  
BELTS  
✓
See the figures that are shown for replacing motion, mower  
drive, and mower blade drive belts in the Service and Ad-  
justments section of this manual. Verify that the belts are  
routed correctly.  
✓
✓
✓
CHECK BRAKE SYSTEM  
Afteryoulearnhowtooperateyourtractor,checktoseethat  
the brake is properly adjusted. See “TO ADJUST BRAKE”  
in the Service and Adjustments section of this manual.  
Before driving tractor, be sure freewheel control is in  
drive position.  
WHILE LEARNING HOW TO USEYOUR TRACTOR, PAY  
EXTRA ATTENTION TO THE FOLLOWING IMPORTANT  
ITEMS:  
✓
Engine oil is at proper level.  
✓
Fuel tank is filled with fresh, clean, regular unleaded  
gasoline.  
✓
Become familiar with all controls - their location and  
function. Operate them before you start the engine.  
✓
✓
Be sure brake system is in safe operating condition.  
It is important to purge the transmission before oper-  
ating your tractor for the first time. Follow proper start-  
ing and transmission purging instructions (See “TO  
START ENGINE” and “PURGE TRANSMISSION” in  
the Operation section of this manual).  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their mean-  
ing.  
IGNITION  
FAST  
SLOW  
REVERSE  
HIGH  
LOW  
NEUTRAL  
CHOKE  
P
LIGHTS ON  
ENGINE START  
ENGINE ON  
PARKING BRAKE  
PARKING BRAKE PARKING BRAKE  
ENGINE OFF  
LOCKED  
UNLOCKED  
OIL PRESSURE  
BATTERY  
REVERSE  
FUEL  
FORWARD  
OVER TEMP  
LIGHT  
MOWER HEIGHT  
MOWER LIFT  
15  
15  
ATTACHMENT  
CLUTCH ENGAGED  
ATTACHMENT  
CLUTCH DISENGAGED  
SLOPE HAZARDS  
KEEP AREA CLEAR  
(SEE SAFETY RULES SECTION)  
DANGER, KEEP HANDS  
AND FEET AWAY  
DANGER indicates a hazard which, if not avoided,  
will result in death or serious injury.  
WARNING indicates a hazard which, if not avoided,  
could result in death or serious injury.  
FREE WHEEL  
(Automatic Models only)  
CAUTION indicates a hazard which, if not avoided,  
might result in minor or moderate injury.  
CAUTION when used without the alert symbol,  
indicates a situation that could result in damage  
to the tractor and/or engine.  
Failure to follow instructions  
could result in serious injury or  
death. The safety alert symbol  
is used to identify safety inform-  
ation about hazards which can  
result in death, serious injury  
and/or property damage.  
HOT SURFACES indicates a hazard which,  
if not avoided, could result in death, serious injury  
and/or property damage.  
FIRE indicates a hazard which, if not avoided,  
could result in death, serious injury and/or  
property damage.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
KNOWYOUR TRACTOR  
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATINGYOUR TRACTOR  
Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments.  
Save this manual for future reference.  
LIGHT  
SWITCH  
POSITION  
HOURMETER  
ATTACHMENT  
CLUTCH SWITCH  
AMMETER  
LIFT LEVER  
PLUNGER  
THROTTLE  
CONTROL  
ELAPSED TIME  
60  
0
0
0
0
0
0
0
1/10  
AM
CHOKE  
CONTROL  
ATTACHMENT  
LIFT LEVER  
CLUTCH/BRAKE  
PEDAL  
IGNITION  
SWITCH  
HEIGHT  
ADJUSTMENT  
KNOB  
FREEWHEEL  
CONTROL  
PARKING BRAKE  
MOTION  
CONTROL  
LEVER  
02770  
FIG. 7  
Our tractors conform to the safety standards of the American National Standards Institute.  
ATTACHMENT CLUTCH SWITCH - Used to engage the  
AMMETER - Indicates charging (+) or discharging (-) of  
mower blades, or other attachments mounted to your  
tractor.  
battery.  
PARKING BRAKE - Locks clutch/brake pedal into the  
brake position.  
LIGHT SWITCH POSITION - Turns the headlights on.  
THROTTLE CONTROL - Used to control engine speed.  
CHOKE CONTROL - Used when starting a cold engine.  
MOTION CONTROL LEVER - Selects the speed and  
direction of tractor.  
ATTACHMENT LIFT LEVER - Used to raise and lower  
the mower deck or other attachments mounted to your  
tractor.  
FREE WHEEL CONTROL - Disengages transmission for  
pushing or slowly towing the tractor with the engine off.  
CLUTCH/BRAKE PEDAL - Used for declutching and  
braking the tractor and starting the engine.  
LIFT LEVER PLUNGER - Used to release attachment lift  
lever when changing its position.  
HEIGHTADJUSTMENTKNOB-Usedtoadjustthemower  
cutting height.  
IGNITION SWITCH - Used for starting and stopping the  
engine.  
HOURMETER - Indicates hours of operation.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
The operation of any tractor can result in foreign objects thrown into the eyes, which can result  
in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or  
performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles  
or standard safety glasses.  
NOTE: Under certain conditions when tractor is standing  
HOW TO USEYOUR TRACTOR  
idlewiththeenginerunning, hotengineexhaustgasesmay  
cause “browning” of grass. To eliminate this possibility, al-  
ways stop engine when stopping tractor on grass areas.  
TO SET PARKING BRAKE (See Fig. 8)  
Your tractor is equipped with an operator presence sens-  
ing switch. When engine is running, any attempt by the  
operator to leave the seat without first setting the parking  
brake will shut off the engine.  
CAUTION: Always stop tractor com-  
pletely,asdescribedabove,beforeleav-  
ing the operator's position; to empty  
grass catcher, etc.  
•
Depress clutch/brake pedal into full “BRAKE” position  
and hold.  
•
Place parking brake lever in“ENGAGED”position and  
releasepressurefromclutch/brakepedal. Pedalshould  
remain in “BRAKE” position. Make sure parking brake  
will hold tractor secure.  
TO USE THROTTLE CONTROL (See Fig. 8)  
Always operate engine at full throttle.  
•
•
Operating engine at less than full throttle reduces the  
battery charging rate.  
Full throttle offers the best bagging and mower perfor-  
mance.  
ATTACHMENT  
PUSH IN TO  
CLUTCH LEVER  
“DISENGAGE”  
PULL OUT TO  
“ENGAGE”  
THROTTLE  
CONTROL  
TO USE CHOKE CONTROL (See Fig. 8)  
Use choke control whenever you are starting a cold engine.  
Do not use to start a warm engine.  
CHOKE  
CONTROL  
PARKING  
BRAKE  
“ENGAGED”  
POSITION  
IGNITION KEY  
•
To engage choke control, pull knob out. Slowly push  
knob in to disengage.  
“BRAKE”  
POSITION  
TO MOVE FORWARD AND BACKWARD  
(See Fig. 8)  
The direction and speed of movement is controlled by the  
motion control lever.  
MOTION  
CONTROL  
LEVER  
“DISENGAGED”  
POSITION  
CLUTCH/BRAKE  
PEDAL “DRIVE”  
POSITION  
HEIGHT  
ADJUSTMENT  
KNOB  
•
Start tractor with motion control lever in neutral (N)  
position.  
FIG. 8  
•
•
Release parking brake.  
Slowly move motion control lever to desired position.  
STOPPING (See Fig. 8)  
MOWER BLADES -  
•
To stop mower blades,move attachment clutch switch  
to “DISENGAGED” position.  
TO ADJUST MOWER CUTTING HEIGHT  
(See Fig. 8)  
The cutting height is controlled by turning the height ad-  
justment knob in desired direction.  
GROUND DRIVE -  
•
To stop ground drive, depress clutch/brake pedal into  
full “BRAKE” position..  
Move motion control lever to neutral (N) position.  
•
•
Turn knob clockwise (  
Turn knob counterclockwise (  
height.  
) to raise cutting height.  
•
) to lower cutting  
IMPORTANT:  
THE MOTION CONTROL LEVER DOES NOT  
RETURN TO NEUTRAL (N) POSITION WHEN THE CLUTCH/  
BRAKE PEDAL IS DEPRESSED.  
The cutting height range is approximately 1-1/2" to 4". The  
heights are measured from the ground to the blade tip with  
theenginenotrunning. Theseheightsareapproximateand  
may vary depending upon soil conditions, height of grass  
and types of grass being mowed.  
ENGINE -  
•
Move throttle control between half and full speed (fast)  
position.  
NOTE: Failure to move throttle control between half and  
fullspeed(fast)position,beforestoppingmaycauseengine  
to “backfire”.  
•
The average lawn should be cut to approximately 2-1/2  
inches during the cool season and to over 3 inches  
during hot months. For healthier and better looking  
lawns, mow often and after moderate growth.  
•
Turn ignition key to “OFF” position and remove key.  
Always remove key when leaving tractor to prevent  
unauthorized use.  
•
For best cutting performance, grass over 6 inches  
in height should be mowed twice. Make the first cut  
relatively high; the second to desired height.  
•
Never use choke to stop engine.  
IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY  
POSITION OTHER THAN "OFF" WILL CAUSE THE BATTERY  
TO BE DISCHARGED, (DEAD).  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
TO ADJUST GAUGE WHEELS (See Fig. 9)  
ATTACHMENT CLUTCH  
SWITCH PULL OUT TO  
"ENGAGE"  
ATTACHMENT  
LIFT LEVER HIGH  
POSITION  
Gaugewheels areproperlyadjustedwhentheyareslightly  
off the ground when mower is at the desired cutting height  
in operating position. Gauge wheels then keep the deck  
in proper position to help prevent scalping in most terrain  
conditions.  
NOTE:Adjust gauge wheels with tractor on a flat level  
surface.  
LOW  
POSITION  
•
Adjust mower to desired cutting height (See “TO AD-  
JUST MOWER CUTTING HEIGHT” in the Operation  
section of this manual).  
•
•
Remove retainer spring and clevis pin which secure  
each gauge wheel bar.  
Lower gauge wheels to ground. Raise gauge wheels  
slightly to align holes in bracket and gauge wheel bar  
and insert clevis pin. Gauge wheels should be slightly  
off the ground.  
PUSH IN TO  
"DISENGAGE"  
DEFLECTOR  
SHIELD  
•
•
Replace retainer spring into clevis pin.  
Be sure all gauge wheels are in the same setting.  
FIG. 10  
IMPORTANT:BESURETOREADJUSTGAUGEWHEELSIFYOU  
CHANGE THE CUTTING HEIGHT OF THE MOWER DECK.  
TO OPERATE ON HILLS  
WARNING: Do not drive up or down  
hills with slopes greater than 15° and  
do not drive across any slope.  
RETAINER  
SPRING  
•
Choose the slowest speed before starting up or down  
hills.  
•
•
Avoid stopping or changing speed on hills.  
If slowing is necessary, move throttle control lever to  
slower position.  
•
If stopping is absolutely necessary, push clutch/brake  
pedal quickly to brake position and engage parking  
brake.  
•
Move motion control lever to neutral (N) position.  
CLEVIS  
PIN  
IMPORTANT:  
THE MOTIONCONTROLLEVERDOESNOT  
RETURN TO NEUTRAL (N) POSITION WHEN THE CLUTCH/  
BRAKE PEDAL IS DEPRESSED.  
•
Torestartmovement, slowlyreleaseparkingbrakeand  
clutch/brake pedal.  
FIG. 9  
•
•
Slowly move motion control lever to slowest setting.  
Make all turns slowly.  
TO OPERATE MOWER (See Fig. 10)  
Your tractor is equipped with an operator presence sens-  
ing switch. Any attempt by the operator to leave the seat  
with the engine running and the attachment clutch engaged  
will shut off the engine.You must remain fully and centrally  
positioned in the seat to prevent the engine from hesitat-  
ing or cutting off when operating your equipment on rough,  
rolling terrain or hills.  
TO TRANSPORT (See Figs. 7 and 11)  
When pushing or towing your tractor, be sure to disengage  
transmission by placing freewheel control in freewheeling  
position. Free wheel control is located at the rear drawbar  
of tractor.  
•
•
•
•
Raiseattachmentlifttohighestpositionwithattachment  
lift control.  
Pull freewheel control out and down into the slot and  
release so it is held in the disengaged position.  
Do not push or tow tractor at more than two (2)  
MPH.  
To reengage transmission, reverse above procedure.  
•
•
•
Select desired height of cut.  
Lower mower with attachment lift control.  
Start mower blades by engaging attachment clutch  
control.  
TO STOP MOWER BLADES - disengage attachment  
clutch control.  
•
CAUTION: Do not operate the mower  
without either the entire grass catcher,  
onmowerssoequipped,orthedeflector  
shield in place.  
NOTE: To protect hood from damage when transporting  
your tractor on a truck or a trailer, be sure hood is closed  
and secured to tractor. Use an appropriate means of tying  
hood to tractor (rope, cord, etc.).  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
CAUTION: Alcohol blended fuels (called  
gasohol or using ethanol or methanol) can at-  
tract moisture which leads to separation and  
formation of acids during storage. Acidic gas  
can damage the fuel system of an engine while  
in storage. To avoid engine problems, the fuel  
system should be emptied before storage of  
30 days or longer. Drain the gas tank, start  
the engine and let it run until the fuel lines  
and carburetor are empty. Use fresh fuel next  
season. SeeStorageInstructionsforadditional  
information. Never use engine or carburetor  
cleaner products in the fuel tank or permanent  
damage may occur.  
FIG. 11  
TOWING CARTS AND OTHER ATTACH-  
MENTS  
Tow only the attachments that are recommended by and  
comply with specifications of the manufacturer of your trac-  
tor. Use common sense when towing.Too heavy of a load,  
while on a slope, is dangerous.Tires can lose traction with  
the ground and cause you to lose control of your tractor.  
TO START ENGINE (See Fig. 8)  
When starting the engine for the first time or if the engine  
has run out of fuel, it will take extra cranking time to move  
fuel from the tank to the engine.  
•
Besurefreewheelcontrolisinthetransmissionengaged  
position.  
BEFORE STARTING THE ENGINE  
•
Sit on seat in operating position, depress clutch/brake  
pedal and set parking brake.  
Place motion control lever in neutral (N) position.  
Move attachment clutch to “DISENGAGED” position.  
Move throttle control to fast position  
Pull choke control out for a cold engine start attempt.  
For a warm engine start attempt the choke control may  
not be needed.  
CHECK ENGINE OIL LEVEL  
The engine in your tractor has been shipped, from the  
factory, already filled with summer weight oil.  
•
•
•
•
•
•
Check engine oil with tractor on level ground.  
Unthread and remove oil fill cap/dipstick; wipe oil off.  
Reinsert the dipstick into the tube and rest oil fill cap on  
the tube. Do not thread the cap onto the tube.Remove  
and read oil level. If necessary, add oil until “FULL”  
mark on dipstick is reached. Do not overfill.  
NOTE: Before starting, read the warm and cold starting  
procedures below.  
•
•
For cold weather operation you should change oil for  
easier starting (See “OIL VISCOSITY CHART” in the  
Maintenance section of this manual).  
To change engine oil, see the Maintenance section in  
this manual.  
•
Insert key into ignition and turn key clockwise to  
“START” position and release key as soon as engine  
starts. Do not run starter continuously for more than  
fifteen seconds per minute.If the engine does not start  
after several attempts, push choke control in, wait a  
few minutes and try again.If engine still does not start,  
pull the choke control out and retry.  
ADD GASOLINE  
•
Fill fuel tank to bottom of filler neck. Do not overfill.  
Use fresh, clean, regular unleaded gasoline with a  
minimum of 87 octane. (Use of leaded gasoline will  
increase carbon and lead oxide deposits and reduce  
valve life). Do not mix oil with gasoline. Purchase fuel  
in quantities that can be used within 30 days to assure  
fuel freshness.  
WARM WEATHER STARTING (50° F and above)  
•
When engine starts, slowly push choke control in until  
the engine begins to run smoothly. If the engine starts  
to run roughly, pull the choke control out slightly for a  
few seconds and then continue to push the control in  
slowly.  
•
The attachments and ground drive can now be used.If  
the engine does not accept the load, restart the engine  
and allow it to warm up for one minute using the choke  
as described above.  
CAUTION: Wipe off any spilled oil or  
fuel. Do not store, spill or use gasoline  
near an open flame.  
COLD WEATHER STARTING (50° F and below)  
IMPORTANT: WHEN OPERATING IN TEMPERATURES  
BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE  
GASOLINE TO HELP INSURE GOOD COLD WEATHER  
STARTING.  
•
When engine starts, slowly push choke control in until  
the engine begins to run smoothly. Continue to push  
the choke control in small steps allowing the engine to  
acceptsmallchangesinspeedandload,untilthechoke  
control is fully in.If the engine starts to run roughly, pull  
the choke control out slightly for a few seconds and  
then continue to push the control in slowly. This may  
requireanenginewarm-upperiodfromseveralseconds  
to several minutes, depending on the temperature.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
AUTOMATIC TRANSMISSION WARM UP  
•
Slowly move motion control lever forward, after the  
tractor moves approximately five (5) feet, slowly move  
motion control lever to reverse position. After the  
tractor moves approximately five (5) feet return the  
motion control lever to the neutral (N) position. Repeat  
this procedure with the motion control lever three (3)  
times.  
•
Beforedrivingtheunitincoldweather,thetransmission  
should be warmed up as follows:  
•
•
Be sure the tractor is on level ground.  
Place the motion control lever in neutral.  
Release the parking brake and let the clutch/  
brake slowly return to operating position.  
Allow one minute for transmission to warm up.This  
can be done during the engine warm up period.  
•
Your transmission is now purged and now ready for  
normal operation.  
•
•
The attachments can be used during the engine warm-  
up period after the transmission has been warmed  
up and may require the choke control be pulled out  
slightly.  
MOWING TIPS  
•
Mower should be properly leveled for best mowing per-  
formance. See“TO LEVEL MOWER HOUSING”in the  
Service and Adjustments section of this manual.  
The left hand side of mower should be used for trim-  
ming.  
Drive so that clippings are discharged onto the area  
that has been cut. Have the cut area to the right of the  
machine. This will result in a more even distribution of  
clippings and more uniform cutting.  
Whenmowinglargeareas,startbyturningtotherightso  
that clippings will discharge away from shrubs, fences,  
driveways, etc. After one or two rounds, mow in the  
opposite direction making left hand turns until finished  
(See Fig. 12).  
NOTE: If at a high altitude (above 3000 feet) or in cold  
temperatures (below 32 F) the carburetor fuel mixture may  
need to be adjusted for best engine performance. See “TO  
ADJUST CARBURETOR” in the Service and Adjustments  
section of this manual.  
•
•
PURGE TRANSMISSION  
•
CAUTION: Never engage or disengage  
freewheel lever while the engine is run-  
ning.  
To ensure proper operation and performance, it is recom-  
mended that the transmission be purged before operating  
tractor for the first time. This procedure will remove any  
trapped air inside the transmission which may have de-  
veloped during shipping of your tractor.  
IMPORTANT: SHOULDYOURTRANSMISSIONREQUIRE  
REMOVAL FOR SERVICE OR REPLACEMENT, IT  
SHOULD BE PURGED AFTER REINSTALLATION  
BEFORE OPERATING THE TRACTOR.  
•
Place tractor safely on level surface with engine off and  
parking brake set.  
00272  
•
Disengage transmission by placing freewheel control  
infreewheelingposition(See“TOTRANSPORT”inthis  
section of manual).  
FIG. 12  
•
•
Sitting in the tractor seat, start engine. After the en-  
gine is running, move throttle control to slow position.  
With motion control lever in neutral (N) position, slowly  
disengage clutch/brake pedal.  
Move motion control lever to full forward position and  
hold for five (5) seconds. Move lever to full reverse  
position and hold for five (5) seconds. Repeat this  
procedure three (3) times.  
•
If grass is extremely tall, it should be mowed twice to  
reduce load and possible fire hazard from dried clip-  
pings. Make first cut relatively high; the second to the  
desired height.  
Do not mow grass when it is wet. Wet grass will plug  
mower and leave undesirable clumps. Allow grass to  
dry before mowing.  
Always operate engine at full throttle when mow-  
ing to assure better mowing performance and proper  
discharge of material. Regulate ground speed by se-  
lecting a low enough gear to give the mower cutting  
performance as well as the quality of cut desired.  
When operating attachments, select a ground speed  
that will suit the terrain and give best performance of  
the attachment being used.  
•
•
NOTE: During this procedure there will be no movement  
of drive wheels. The air is being removed from hydraulic  
drive system.  
•
Move motion control lever to neutral (N) position. Shut-  
off engine and set parking brake.  
Engage transmission by placing freewheel control in  
driving position (See“TOTRANSPORT”in this section  
of manual).  
•
•
•
Sittinginthetractor seat, startengine. Aftertheengine  
is running, move throttle control to half (1/2) speed.  
With motion control lever in neutral (N) position, slowly  
disengage clutch/brake pedal.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
MAINTENANCE SCHEDULE  
USE  
HOURS  
HOURS  
FILL IN DATES  
HOURSHOURS  
50 100  
STORAGE  
EACH  
8
25  
SEASON  
AS YOU COMPLETE  
REGULAR SERVICE  
BEFORE SERVICE DATES  
EVERY EVERY EVERY EVERY EVERY  
BEFORE  
Check Brake Operation  
Check Tire Pressure  
Check Operator Presence and  
Interlock Systems  
T
Check for Loose Fasteners  
R
5
A
Sharpen/Replace Mower Blades  
3
C
Lubrication Chart  
T
Check Battery Level  
4
0
Clean Battery and Terminals  
R
Check Transaxle Cooling  
Check V-Belts  
Check Engine Oil Level  
Change Engine Oil (with oil filter)  
1,2  
Change Engine Oil (without oil filter)  
1,2  
E
Clean Air Filter  
N
2
2
G
Clean Air Screen  
I
Inspect Muffler/Spark Arrester  
N
Replace Oil Filter (If equipped)  
1,  
2
2
E
Clean Engine Cooling Fins  
Replace Spark Plug  
Replace Air Filter Paper Cartridge  
Replace Fuel Filter  
2
3 - Replace blades more often when mowing in sandy soil.  
4 - Not required if equipped with maintenance-free battery.  
5 - Tighten front axle pivot bolt to 35 ft.-lbs. maximum.  
Do not overtighten.  
1 - Change more often when operating under a heavy load or  
in high ambient temperatures.  
2 - Service more often when operating in dirty or dusty conditions.  
LUBRICATION CHART  
GENERAL RECOMMENDATIONS  
The warranty on this tractor does not cover items that have  
beensubjectedtooperatorabuseornegligence. Toreceive  
full value from the warranty, operator must maintain tractor  
as instructed in this manual.  
SPINDLE ZERK  
SPINDLE ZERK  
➀
➀
FRONT  
WHEEL  
BEARING  
ZERK  
➀
FRONT  
WHEEL  
BEARING  
ZERK  
➀
Some adjustments will need to be made periodically to  
properly maintain your tractor.  
At least once a season, check to see if you should make  
any of the adjustments described in the Service and  
Adjustments section of this manual.  
ENGINE  
➁
• At least once a year you should replace the spark plug,  
clean or replace air filter, and check blades and belts  
for wear. A new spark plug and clean air filter assure  
proper air-fuel mixture and help your engine run better  
and last longer.  
01964  
BEFORE EACH USE  
➀ General Purpose Grease  
➁ Refer to Maintenance “ENGINE” Section  
•
•
•
•
Check engine oil level.  
Check brake operation.  
Check tire pressure.  
Check operator presence and  
interlock systems for proper operation.  
Check for loose fasteners.  
IMPORTANT: DO NOT OIL OR GREASE THE PIVOT POINTS  
WHICH HAVE SPECIAL NYLON BEARINGS. VISCOUS  
LUBRICANTS WILL ATTRACT DUST AND DIRT THAT WILL  
SHORTENTHE LIFE OFTHE SELF-LUBRICATING BEARINGS.  
IFYOU FEELTHEY MUST BE LUBRICATED, USE ONLY A DRY,  
POWDERED GRAPHITE TYPE LUBRICANT SPARINGLY.  
•
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
TRACTOR  
Always observe safety rules when performing any main-  
tenance.  
BLADE  
MANDREL  
ASSEMBLY  
CENTER  
HOLE  
BRAKE OPERATION  
BLADE BOLT  
(SPECIAL)  
If tractor requires more than six (6) feet stopping distance  
at high speed in highest gear, then brake must be adjusted.  
(See“TOADJUSTBRAKE”intheServiceandAdjustments  
section of this manual).  
STAR  
FIG. 13  
TIRES  
•
•
•
Maintainproperairpressureinalltires(See“PRODUCT  
SPECIFICATIONS” section of this manual).  
TO SHARPEN BLADE (See Fig. 14)  
NOTE: We do not recommend sharpening blade - but if  
you do, be sure the blade is balanced.  
Keep tires free of gasoline, oil, or insect control chemi-  
cals which can harm rubber.  
Avoid stumps, stones, deep ruts, sharp objects and  
other hazards that may cause tire damage.  
Care should be taken to keep the blade balanced. An un-  
balancedbladewillcauseexcessivevibrationandeventual  
damage to mower and engine.  
NOTE: To seal tire punctures and prevent flat tires due to  
slow leaks, tire sealant may be purchased from your local  
parts dealer. Tire sealant also prevents tire dry rot and  
corrosion.  
•
The blade can be sharpened with a file or on a grind-  
ing wheel. Do not attempt to sharpen while on the  
mower.  
•
To check blade balance, you will need a 5/8" diameter  
steel bolt, pin, or a cone balancer. (When using a  
cone balancer, follow the instructions supplied with  
balancer.)  
OPERATOR PRESENCE SYSTEM  
Besureoperatorpresenceandinterlocksystemsarework-  
ing properly. If your tractor does not function as described,  
repair the problem immediately.  
NOTE: Do not use a nail for balancing blade. The lobes of  
the center hole may appear to be centered, but are not.  
•
•
•
•
•
The engine should not start unless the clutch/brake  
pedalisfullydepressedandattachementclutchcontrol  
is in the disengaged position.  
Whentheengineisrunning,anyattemptbytheoperator  
to leave the seat without first setting the parking brake  
should shut off the engine.  
When the engine is running and the attachment clutch  
is engaged, any attempt by the operator to leave the  
seat should shut off the engine.  
The attachment clutch should never operate unless  
the operator is in the seat.  
Slidebladeontoanunthreadedportionofthesteelbolt  
or pin and hold the bolt or pin parallel with the ground.  
If blade is balanced, it should remain in a horizontal  
position. If either end of the blade moves downward,  
sharpen the heavy end until the blade is balanced.  
CENTER  
HOLE  
BLADE  
5/8" BOLT OR PIN  
BLADE CARE  
Forbestresultsmowerbladesmustbekeptsharp. Replace  
bent or damaged blades.  
FIG. 14  
BLADE REMOVAL (See Fig. 13)  
BATTERY  
•
Raise mower to highest position to allow access to  
blades.  
Yourtractorhasabatterychargingsystemwhichissufficient  
for normal use. However, periodic charging of the battery  
with an automotive charger will extend its life.  
NOTE: Protect your hands with gloves and/or wrap blade  
with heavy cloth.  
•
•
•
•
Keep battery and terminals clean.  
Keep battery bolts tight.  
Keep small vent holes open.  
Recharge at 6-10 amperes for 1 hour.  
•
•
Remove blade bolt by turning counterclockwise.  
Install new or resharpened blade with stamped "THIS  
SIDE UP" facing deck and mandrel assembly.  
IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER  
HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL  
ASSEMBLY.  
NOTE: The original equipment battery on your tractor is  
maintenance free. Do not attempt to open or remove caps  
or covers. Adding or checking level of electrolyte is not  
necessary.  
•
Install and tighten blade bolt securely (45-55 Ft. Lbs.  
torque).  
TO CLEAN BATTERY AND TERMINALS  
IMPORTANT: SPECIAL BLADE BOLT HEAT TREATED.  
Corrosion and dirt on the battery and terminals can cause  
the battery to “leak” power.  
•
Remove terminal guard.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
•
•
Catch oil in a suitable container.  
Remove oil fill cap/dipstick. Be careful not to allow dirt  
to enter the engine when changing oil.  
Remove yellow cap from end of drain valve and install  
the drain tube onto the fitting.  
•
Disconnect BLACK battery cable first then RED bat-  
tery cable and remove battery from tractor.  
Rinse the battery with plain water and dry.  
Cleanterminalsandbatterycableendswithwirebrush  
until bright.  
•
•
•
•
•
Coat terminals with grease or petroleum jelly.  
OIL DRAIN VALVE  
Reinstall battery (See “REPLACING BATTERY" in  
the SERVICE AND ADJUSTMENTS section of this  
manual).  
V-BELTS  
CLOSED  
Check V-belts for deterioration and wear after 100 hours  
of operation and replace if necessary. The belts are not  
adjustable. Replace belts if they begin to slip from wear.  
AND  
LOCKED  
POSITION  
TRANSAXLE COOLING  
The transmission fan and cooling fins should be kept clean  
to assure proper cooling.  
YELLOW  
CAP  
DRAIN  
TUBE  
Do not attempt to clean fan or transmission while engine  
is running or while the transmission is hot.To prevent pos-  
sible damage to seals, do not use high pressure water or  
steam to clean transaxle.  
FIG. 16  
•
Inspect cooling fan to be sure fan blades are intact and  
clean.  
Inspect cooling fins for dirt, grass clippings and other  
materials. To prevent damage to seals, do not use  
compressed air or high pressure sprayer to clean cool-  
ing fins.  
•
Unlock drain valve by pushing inward and turning  
counterclockwise.  
To open, pull out on the drain valve.  
After oil has drained completely, close and lock the  
drain valve by pushing inward and turning clockwise  
until the pin is in the locked position as shown.  
•
•
•
•
•
Remove the drain tube and replace the cap onto to the  
bottom fitting of the drain valve.  
Refill engine with oil through oil fill dipstick tube. Pour  
slowly. Do not overfill. For approximate capacity see  
“PRODUCT SPECIFICATIONS” section of this man-  
ual.  
TRANSAXLE PUMP FLUID  
The transaxle was sealed at the factory and fluid mainte-  
nance is not required for the life of the transaxle. Should  
the transaxle ever leak or require servicing, contact your  
nearest authorized service center/department.  
•
Use gauge on oil fill cap/dipstick for checking level.  
Insert dipstick into the tube and rest the oil fill cap on  
the tube. Do not thread the cap onto the tube when  
taking reading. Keep oil at “FULL” line on dipstick.  
Tighten cap onto the tube securely when finished.  
ENGINE  
LUBRICATION  
Only use high quality detergent oil rated with API service  
classification SF-SJ. Select the oil’s SAE viscosity grade  
according to your expected operating temperature.  
CLEAN AIR SCREEN  
SAE VISCOSITY GRADES  
Air screen must be kept free of dirt and chaff to prevent  
engine damage from overheating. Clean with a wire brush  
or compressed air to remove dirt and stubborn dried gum  
fibers.  
10W30  
5W-30  
-20  
0
30  
32 40  
0
100  
60  
80  
F
C
-20  
10  
-30  
-10  
20  
30  
40  
CLEAN AIR INTAKE/COOLING AREAS  
TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE  
oil_visc_chart4_e  
To insure proper cooling, make sure the grass screen,  
cooling fins, and other external surfaces of the engine are  
kept clean at all times.  
FIG. 15  
Change the oil after every 50 hours of operation or at least  
once a year if the tractor is not used for 50 hours in one  
year.  
Every 100 hours of operation (more often under extremely  
dusty, dirty conditions), remove the blower housing and  
other cooling shrouds. Clean the cooling fins and external  
surfaces as necessary. Make sure the cooling shrouds are  
reinstalled.  
Check the crankcase oil level before starting the engine  
and after each eight (8) hours of operation.  
TO CHANGE ENGINE OIL (See Figs. 15 and 16)  
NOTE: Operating the engine with a blocked grass screen,  
dirtyorpluggedcoolingfins,and/orcoolingshroudsremoved  
will cause engine damage due to overheating.  
Determine temperature range expected before oil change.  
All oil must meet API service classification SF-SJ.  
•
•
Be sure tractor is on level surface.  
Oil will drain more freely when warm.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
AIR FILTER  
Your engine will not run properly using a dirty air filter.  
Service air cleaner more often under dusty conditions.  
See Engine Manual.  
IN-LINE FUEL FILTER (See Fig. 17)  
The fuel filter should be replaced once each season. If fuel  
filter becomes clogged, obstructing fuel flow to carburetor,  
replacement is required.  
•
•
•
•
With engine cool, remove filter and plug fuel line sec-  
tions.  
ENGINE OIL FILTER  
Replace the engine oil filter every season or every other  
oil change if the tractor is used more than 100 hours in  
one year.  
Place new fuel filter in position in fuel line with arrow  
pointing towards carburetor.  
Be sure there are no fuel line leaks and clamps are  
properly positioned.  
MUFFLER  
Immediately wipe up any spilled gasoline.  
Inspect and replace corroded muffler and spark arrester  
(if equipped) as it could create a fire hazard and/or dam-  
age.  
CLAMP  
CLAMP  
SPARK PLUGS  
FUEL  
FILTER  
Replace spark plugs at the beginning of each mowing  
season or after every 100 hours of operation, whichever  
occurs first. Spark plug type and gap setting are shown in  
“PRODUCT SPECIFICATIONS” section of this manual.  
00667  
FIG. 17  
CLEANING  
•
•
•
Clean engine, battery, seat, finish, etc. of all foreign  
matter.  
Keep finished surfaces and wheels free of all gasoline,  
oil, etc.  
Protect painted surfaces with automotive type wax.  
We do not recommend using a garden hose or pressure  
washer to clean your tractor unless the engine and trans-  
mission are covered to keep water out. Water in engine or  
transmission will shorten the useful life of your tractor. Use  
compressed air or a leaf blower to remove grass, leaves  
and trash from tractor and mower.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUST-  
MENTS:  
•
•
•
•
•
•
Depress clutch/brake pedal fully and set parking brake.  
Place motion control lever in neutral (N) position.  
Place attachment clutch in “DISENGAGED” position.  
Turn ignition key to “STOP” and remove key.  
Make sure the blades and all moving parts have completely stopped.  
Disconnect spark plug wire from spark plug and place wire where it cannot come in contact  
with plug.  
•
If equipped, turn height adjustment knob counter-  
clockwise until it stops.  
Lower mower linkage with attachment lift control.  
Install belt into electric clutch pulley groove.  
Place the suspension arms on outward pointing deck  
pins. Retain with double loop retainer spring with loops  
up as shown.  
Install front plate assembly to tractor suspension  
brackets and retain with single loop retainer springs  
as shown.  
Position front plate assembly between front mower  
brackets.Raise deck and plate assembly to align holes  
and insert flanged pins. Secure pins with double loop  
retainer springs between the plate and mower brack-  
ets.  
TRACTOR  
TO REMOVE MOWER (See Fig. 18)  
•
•
•
•
•
Place attachment clutch in “DISENGAGED” position.  
If equipped, turn height adjustment knob to lowest  
setting.  
•
•
Lower mower to its lowest position.  
Removeretainerspringholdinganti-swaybartochassis  
bracket and disengage anti-swaybar from bracket.  
•
•
•
•
Removefourretainerspringsfromfrontplateassembly  
and remove plate.  
Removeretainerspringsfromsuspensionarmsatdeck  
and disengage arms from deck.  
•
•
Raise attachment lift to its highest position.  
Slide mower forward and remove belt from electric  
clutch pulley.  
NOTE: To assist in locating hole in flanged pin, the hole in  
pin is inline with notch on head of pin. If necessary, move  
mowerside-to-sidetogivespacebetweenplateandmower  
brackets.  
IMPORTANT: CHECK BELT FOR PROPER ROUTING IN ALL  
MOWER PULLEY GROOVES.  
•
•
•
•
Slide mower out from under right side of tractor.  
TO INSTALL MOWER  
Be sure tractor is on level surface and mower suspension  
arms are raised with attachment lift control. Engage park-  
ing brake.  
Connect anti-sway bar to chassis bracket under left  
footrest and retain with double loop retainer spring.  
If equipped, turn height adjustment knob clockwise to  
remove slack from mower suspension.  
•
•
Swing anti-sway bar to left side of mower deck.  
Slide mower under tractor with deflector shield to right  
side of tractor.  
Raise deck to highest position.  
IMPORTANT: CHECK BELT FOR PROPER ROUTING IN ALL  
MOWER PULLEY GROOVES.  
ELECTRIC CLUTCH PULLEY  
FRONT MOWER  
BRACKET  
FRONT PLATE ASSEMBLY  
CHASSIS  
BRACKET  
SUSPENSION ARMS  
DOUBLE LOOP  
RETAINER SPRING  
SINGLE LOOP  
REATINER  
SPRING  
RETAINER  
SPRING  
FLANGED PINS  
USE PLIERS FOR  
RETAINER SPRINGS  
ANTI-SWAY  
BAR  
SUSPENSION ARMS  
DOUBLE LOOP  
RETAINER SPRINGS  
(Outward pointing  
deck pins)  
LOOP UP  
02566  
FIG. 18  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
NOTE: Each full turn of nut “C” will change distance. “B”  
by approximately 3/16".  
TO LEVEL MOWER HOUSING  
Adjust the mower while tractor is parked on level ground  
or driveway. Make sure tires are properly inflated (See  
“PRODUCT SPECIFICATIONS”section of this manual). If  
tires are over or underinflated, you will not properly adjust  
your mower.  
•
Whendistance“B”is1/8"to1/2"loweratfrontthanrear,  
tighten nut “D” against trunnion on both front links.  
To raise front of blade, loosen nut “D” from trunnion on  
both front links. Tighten nut “C” on both front links an  
equal number of turns.The two front links must remain  
equal in length.  
•
SIDE-TO-SIDE ADJUSTMENT (See Figs. 19 and 20)  
•
•
Whendistance“B”is1/8"to1/2"loweratfrontthanrear,  
•
•
Raise mower to its highest position.  
Measure height from bottom edge of mower to ground  
level at front corners of mower. Distance “A” on both  
sides of mower should be the same.  
If adjustment is necessary, make adjustment on one  
side of mower only.  
To raise one side of mower, tighten lift link adjustment  
nut on that side.  
To lower one side of mower, loosen lift link adjustment  
nut on that side.  
tighten nut “D” against trunnion on both front links.  
Recheck side-to-side adjustment.  
BLADE  
•
•
•
“B”  
“B”  
NOTE: Each full turn of adjustment nut will change mower  
height about 3/16".  
FIG. 21  
•
Recheck measurements after adjusting.  
BOTH FRONT PLATE LINKS MUST BE  
EQUAL IN LENGTH  
BOTTOM EDGE  
OF MOWER TO  
GROUND  
BOTTOM EDGE  
OF MOWER TO  
GROUND  
A
A
GROUND LINE  
FIG. 19  
SUSPENSION  
ARM  
NUT “C”  
NUT “D”  
TRUNNION  
FRONT PLATE  
ASSEMBLY  
LIFT LINK  
ADJUSTMENT NUT  
FIG. 20  
FIG. 22  
FRONT-TO-BACK ADJUSTMENT (See Figs. 21 and 22)  
IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE  
FOLLOWINGFRONT-TO-BACKADJUSTMENTISNECESSARY,  
BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO  
MOWER WILL STAY LEVEL SIDE-TO-SIDE.  
To obtain the best cutting results, the mower blades should  
be adjusted so the front tip is approximately 1/8" to 1/2"  
lower than the rear tip when the mower is in its highest  
position.  
CAUTION: Blades are sharp. Protect  
your hands with gloves and/or wrap  
blade with heavy cloth.  
Checkadjustmentonrightsideoftractor. Positionanyblade  
so the tip is pointing straight forward.Measure distance "B"  
at front and rear tip of the blade.  
•
•
•
Before making any necessary adjustments, check that  
both front plate links are equal in length.  
If links are not equal in length, adjust one link to same  
length as other link.  
To lower front of blade, loosen nut “C” on both front  
links an equal number of turns.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
TO REPLACE MOWER DRIVE BELT  
MOWER DRIVE BELT REMOVAL (See Fig. 23)  
TOREPLACEMOWERBLADE(SECONDARY)  
DRIVE BELT (See Fig. 24)  
•
•
Park tractor on a level surface. Engage parking  
Park the tractor on level surface. Engage parking brake.  
brake.  
•
•
Remove mower (See “TO REMOVE MOWER” in this  
Lower mower to its lowest position.  
section of manual).  
Remove screws from R.H. and L.H. mandrel covers  
and remove covers.  
Remove screws from R.H. mandrel cover and remove  
cover.  
•
•
Remove any dirt or grass clippings which may have  
accumulated around mandrels and entire upper deck  
surface.  
DisconnectR.H.suspensionarmfromreardeckbracket  
by removing retainer spring.  
Roll belt over the top of R.H. mandrel pulley carefully.  
Remove belt from electric clutch pulley.  
Remove belt from idler pulleys.  
Check primary idler arm and two idlers to see that they  
rotate freely.  
REMOVE MOWER DRIVE BELT  
(Refer to “TO REMOVE MOWER DRIVE BELT” illustration  
in this section of manual).  
•
•
•
Carefully roll belt over the top of R.H. mandrel pulley.  
Remove belt from idler pulleys.  
Check primary idler arm and two idlers to see that they  
rotate freely.  
•
•
•
•
•
Be sure spring is securely hooked to primary idler arm  
and spring arm.  
REMOVE MOWER BLADE (SECONDARY) DRIVE BELT  
•
•
Carefully roll belt off L.H. mandrel pulley.  
Remove belt from center mandrel pulley, idler pulley,  
and R.H. mandrel pulley.  
•
Be sure spring is securely hooked to primary idler arm  
and spring arm.  
MOWER DRIVE BELT INSTALLATION (See Fig. 23)  
•
•
•
Removeanydirtorgrasswhichmayhaveaccumulated  
around mandrels and entire upper deck surface.  
Check secondary idler arm and idler pulley to see that  
they rotate freely.  
Be sure spring is hooked in secondary idler arm and  
secondary spring arm.  
•
•
•
Install belt in both idlers.  
Install new belt onto electric clutch pulley.  
Roll belt into upper groove of R.H.mandrel pulley care-  
fully.  
Carefully check belt routing making sure belt is in the  
grooves correctly.  
Reconnect R.H. suspension arm to rear deck bracket  
with retainer spring.  
Reassemble R.H. mandrel cover.  
•
•
•
INSTALL NEW MOWER BLADE (SECONDARY) DRIVE  
BELT  
•
Install new belt in lower groove of R.H. mandrel pulley,  
idler pulley, and center mandrel pulley as shown.  
•
Carefully roll belt over L.H. mandrel pulley. Make sure  
belt is in all grooves properly.  
RH MANDREL COVER  
IDLER  
REINSTALL MOWER DRIVE BELT  
(Refer to “TO REMOVE MOWER DRIVE BELT” illustration  
in this section of manual).  
PULLEYS  
ELECTRIC  
CLUTCH  
PULLEY  
•
Install belt into upper groove of R.H. mandrel pulley  
and around both idlers. Pull belt to front of mower to  
remove slack.  
•
•
•
Reinstall mandrel covers and securely tighten all  
screws.  
Carefully check belt routing making sure belt is in all  
grooves correctly.  
Reinstallmowertotractor(See“TOINSTALLMOWER”  
in this section of manual).  
R.H.  
MANDREL  
SPRING  
ARM  
SECONDARY  
IDLER ARM  
L.H. MANDREL  
RH SUSPENSION  
ARM  
SPRING  
SECONDARY  
SPRING ARM  
PRIMARY IDLER ARM  
CENTER  
MANDREL  
FIG. 23  
IDLER  
PULLEY  
R.H. MANDREL  
FIG. 24  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
TO CHECK AND ADJUST BRAKE  
TO REPLACE MOTION DRIVE BELT  
(See Fig. 26)  
Park the tractor on level surface. Engage parking brake.  
For assistance, there is a belt installation guide decal on  
bottom side of left footrest.  
(See Fig. 25)  
Your tractor is equipped with an adjustable brake system  
which is mounted on the right side of the transaxle.  
If tractor requires more than five (5) feet to stop at highest  
speed in highest gear on a level, dry concrete or paved  
surface, then brake must be checked and adjusted.  
BELT REMOVAL -  
•
Remove mower (See “TO REMOVE MOWER” in this  
TO CHECK BRAKE  
section of manual).  
•
Park tractor on a level, dry concrete or paved surface,  
depress clutch/brake pedal all the way down and en-  
gage parking brake.  
NOTE: Observe entire motion drive belt and position of all  
belt guides and keepers.  
•
•
•
•
•
Disengage transmission by placing freewhel control  
in “transmission disengaged” position. Pull freewheel  
control out and into the slot and release so it is held in  
the disengaged position.  
Disconnect clutch wire harness.  
Remove clutch locator.  
Remove belt from stationary idler and clutching idler.  
Remove belt downward from engine pulley and around  
electric clutch.  
Pull belt slack toward rear of tractor. Carefully remove  
belt upwards from transmission input pulley and over  
cooling fan blades.  
Remove belt from center span keeper and pull belt  
away from tractor.  
Therearwheelsmustlockandskidwhenyoutrytomanually  
push the tractor forward.If the rear wheels rotate, the brake  
needs to be adjusted or the pads need to be replaced.  
•
•
TO ADJUST BRAKE  
•
•
•
Depress clutch/brake pedal all the way down and en-  
gage parking brake.  
Measure distance between brake operating arm and  
nut “A” on brake rod.  
If distance is other than 1-9/16", loosen jam nut and  
turn nut “A” until distance becomes 1-9/16". Retighten  
jam nut against nut “A”.  
BELT INSTALLATION -  
•
Carefully work new belt down around transmission  
cooling fan and onto the input pulley.  
Slide belt into the center span keeper.  
Pull belt toward front of tractor and roll belt around  
electric clutch and onto engine pulley.  
Install belt through stationary idler and clutching  
idler.  
Reinstall clutch locator and tighten nut securely.  
Reconnect clutch harness.  
Make sure belt is in all pulley grooves and inside all  
belt guides and keepers.  
Install mower (See “TO INSTALL MOWER” in this sec-  
tion of manual).  
•
•
•
Engage transmission by placing freewheel control in  
“transmission engaged” position.  
Roadtesttractorforproperstoppingdistanceasstated  
above. Readjust if necessary. If stopping distance is  
still greater than five (5) feet in highest gear, further  
maintenance is necessary. Replace brake pads or  
contact a qualified service center.  
•
•
•
•
WITH PARKING BRAKE “ENGAGED”  
1-9/16”  
•
ELECTRIC  
CLUTCH  
CLUTCH  
LOCATOR  
NUT “A”  
JAM NUT  
CLUTCHING  
IDLER  
OPERATING  
ARM  
STATIONARY  
IDLER  
01513  
DO NOT TOUCH THIS NUT. IF FURTHER BRAKE ADJUSTMENT  
IS NECESSARY CONTACTYOUR NEAREST AUTHORIZED SER-  
VICE CENTER/DEPARTMENT  
CENTER SPAN  
KEEPER  
FIG. 25  
TRANSMISSION  
INPUT PULLEY  
CLUTCH  
WIRE  
HARNESS  
FIG. 26  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
TRANSAXLE MOTION CONTROL LEVER  
TO REMOVE WHEEL FOR REPAIRS  
NEUTRAL ADJUSTMENT (See Fig. 27)  
(See Fig. 28)  
•
•
Block up axle securely.  
The motion control lever has been preset at the factory and  
adjustment should not be necessary.  
Removeaxlecover, retainingringandwasherstoallow  
wheel removal (rear wheel contains a square key - Do  
not lose).  
•
•
•
•
•
•
Loosen adjustment bolt in front of the right rear wheel,  
and lightly tighten.  
Start engine and move motion control lever until tractor  
does not move forward or backward.  
Holdmotioncontrolleverinthatpositionandturnengine  
off.  
While holding motion control lever in place, loosen the  
adjustment bolt.  
•
•
Repair tire and reassemble.  
On rear wheels only: align grooves in rear wheel hub  
and axle. Insert square key.  
•
•
Replace washers and snap retaining ring securely in  
axle groove.  
Replace axle cover.  
NOTE: To seal tire punctures and prevent flat tires due  
to slow leaks, tire sealant may be purchased from your  
local parts dealer. Tire sealant also prevents tire dry rot  
and corrosion.  
Move motion control lever to the neutral (N) (lock gate)  
position.  
Tighten adjustment bolt securely.  
NOTE: If additional clearance is needed to get to  
adjustment bolt, move mower deck height to the lowest  
osition.  
After above adjustment is made, if the tractor still creeps  
forward or backward while motion control lever is in  
neutral position, follow these steps:  
WASHERS  
RETAINING  
•
•
Loosen the adjustment bolt.  
RING  
AXLE  
COVER  
Move the motion control lever 1/4 to 1/2 inch in the  
direction it is trying to creep.  
•
•
•
Tighten adjustment bolt securely.  
Start engine and test.  
If tractor still creeps, repeat above steps until satis-  
fied.  
SQUARE KEY  
00663  
(REAR WHEEL ONLY)  
FIG. 28  
MOTION CONTROL  
NEUTRAL  
LEVER  
LOCK GATE  
TO START ENGINE WITH A WEAK  
BATTERY(See Fig. 29)  
WARNING: Lead-acid batteries gen-  
erate explosive gases. Keep sparks,  
flameandsmokingmaterialsawayfrom  
batteries. Always wear eye protection  
when around batteries.  
ADJUSTMENT  
BOLT  
02239  
FIG. 27  
If your battery is too weak to start the engine, it should be  
recharged. (See "BATTERY" in the MAINTENANCE sec-  
tion of this manual).  
TRANSMISSION REMOVAL/REPLACEMENT  
Should your transmission require removal for service or  
replacement, it should be purged after reinstallation and  
beforeoperatingthetractor. See“PURGETRANSMISSION”  
in the Operation section of this manual.  
If “jumper cables” are used for emergency starting, follow  
this procedure:  
IMPORTANT: YOURTRACTOR IS EQUIPPEDWITH A 12VOLT  
SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT  
SYSTEM. DO NOT USEYOUR TRACTOR BATTERY TO START  
OTHER VEHICLES.  
TO ADJUST STEERING WHEEL  
ALIGNMENT  
If steering wheel crossbars are not horizontal (left to right)  
whenwheelsarepositionedstraightforward,removesteer-  
ing wheel and reassemble per instructions in the Assembly  
section of this manual.  
TO ATTACH JUMPER CABLES -  
•
Connect one end of the RED cable to the POSITIVE  
(+) terminal of each battery(A-B), taking care not to  
short against tractor chassis.  
•
•
ConnectoneendoftheBLACKcabletotheNEGATIVE  
(-) terminal (C) of fully charged battery.  
Connect the other end of the BLACK cable (D) to good  
chassis ground, away from fuel tank and battery.  
FRONT WHEEL TOE-IN/CAMBER  
The front wheel toe-in and camber are not adjustable on  
your tractor. If damage has occurred to affect the front  
wheel toe-in or camber, contact your nearest authorized  
service center/department.  
TO REMOVE CABLES, REVERSE ORDER -  
•
BLACK cable first from chassis and then from the fully  
charged battery.  
•
RED cable last from both batteries.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
TO REPLACE HEADLIGHT BULB  
•
•
Raise hood.  
Pull bulb holder out of the hole in the backside of the  
grill.  
•
•
Replace bulb in holder and push bulb holder securely  
back into the hole in the backside of the grill.  
Close hood.  
INTERLOCKS AND RELAYS  
Loose or damaged wiring may cause your tractor to run  
poorly, stop running, or prevent it from starting.  
WEAK OR DEAD  
BATTERY  
FULLY CHARGED  
BATTERY  
•
Check wiring. See electrical wiring diagram in the  
Repair Parts section.  
FIG. 29  
TO REPLACE FUSE  
Replace with 20 amp automotive-type plug-in fuse. The  
fuse holder is located behind the dash.  
REPLACING BATTERY (See Fig. 30)  
WARNING: Do not short battery  
terminals by allowing a wrench or any  
other object to contact both terminals  
at the same time. Before connect-  
ing battery, remove metal bracelets,  
wristwatch bands, rings, etc.  
Positive terminal must be connected  
first to prevent sparking from acci-  
dental grounding.  
TO REMOVE HOOD AND GRILL ASSEMBLY  
(See Fig. 31)  
•
•
•
Raise hood.  
Unsnap headlight wire connector.  
Stand in front of tractor. Grasp hood at sides, tilt toward  
engine and lift off of tractor.  
•
To replace, reverse above procedures.  
•
•
•
Lift hood to raised position.  
Remove terminal guard.  
Disconnect BLACK battery cable then RED battery  
cable and carefully remove battery from tractor.  
HOOD  
•
Install new battery with terminals in same position as  
old battery.  
HEADLIGHT  
WIRE  
CONNECTOR  
•
•
Reinstall terminal guard.  
First connect RED battery cable to positive (+) battery  
terminal with hex bolt and keps nut as shown.Tighten  
securely.  
ConnectBLACKgroundingcabletonegative(-)battery  
terminal with remaining hex bolt and keps nut.Tighten  
securely  
02778  
•
•
•
Close terminal access doors.  
Close hood.  
FIG. 31  
KEPS NUT  
TERMINAL  
ACCESS  
DOOR  
HEX BOLT  
POSITIVE  
(RED)  
CABLE  
TERMINAL  
GUARD  
NEGATIVE  
(BLACK)  
CABLE  
FIG. 30  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
ENGINE  
TO ADJUST THROTTLE CONTROL CABLE  
The throttle control has been preset at the factory and  
adjustment should not be necessary. If adjustment is nec-  
essary, see engine manual.  
TO ADJUST CHOKE CONTROL  
The choke control has been preset at the factory and ad-  
justment should not be necessary. If adjustment is neces-  
sary, see engne manual.  
TO ADJUST CARBURETOR  
Your carburetor is not adjustable. If your engine does not  
operate properly due to suspected carburetor problems,  
take your tractor to an authorized service center for repair  
and/or adjustment.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STORAGE  
Immediately prepare your tractor for storage at the end  
of the season or if the tractor will not be used for 30 days  
or more.  
ENGINE  
FUEL SYSTEM  
IMPORTANT: ITISIMPORTANTTOPREVENTGUMDEPOSITS  
FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH  
AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK  
DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT  
ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING  
ETHANOLORMETHANOL)CANATTRACTMOISTUREWHICH  
LEADSTOSEPARATIONANDFORMATIONOFACIDSDURING  
STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM  
OF AN ENGINE WHILE IN STORAGE.  
WARNING: Never store the tractor with  
gasoline in the tank inside a building  
where fumes may reach an open flame  
orspark. Allowtheenginetocoolbefore  
storing in any enclosure.  
TRACTOR  
•
•
•
Empty the fuel tank by starting the engine and let it run  
until the fuel lines and carburetor are empty.  
Never use engine or carburetor cleaner products in the  
fuel tank or permanent damage may occur.  
Removemowerfromtractorforwinterstorage. Whenmower  
istobestoredforaperiodoftime,cleanitthoroughly,remove  
all dirt, grease, leaves, etc. Store in a clean, dry area.  
•
Clean entire tractor (See “CLEANING” in the Mainte-  
nance section of this manual).  
Use fresh fuel next season.  
NOTE: Fuel stabilizer is an acceptable alternative in mini-  
mizing the formation of fuel gum deposits during storage.  
Add stabilizer to gasoline in fuel tank or storage container.  
Always follow the mix ratio found on stabilizer container.  
Run engine at least 10 minutes after adding stabilizer to  
allow the stabilizer to reach the carburetor. Do not empty  
the gas tank and carburetor if using fuel stabilizer.  
•
Inspect and replace belts, if necessary (See belt re-  
placement instructions in the Service and Adjustments  
section of this manual).  
•
•
Lubricate as shown in the Maintenance section of this  
manual.  
Be sure that all nuts, bolts and screws are securely  
fastened. Inspect moving parts for damage, breakage  
and wear. Replace if necessary.  
ENGINE OIL  
•
Touch up all rusted or chipped paint surfaces; sand  
lightly before painting.  
Drain oil (with engine warm) and replace with clean en-  
gine oil. (See “ENGINE” in the Maintenance section of  
this manual).  
BATTERY  
CYLINDER(S)  
•
•
Fully charge the battery for storage.  
•
•
Remove spark plug(s).  
After a period of time in storage, battery may require  
recharging.  
Pour one ounce of oil through spark plug hole(s) into  
cylinder(s).  
•
To help prevent corrosion and power leakage during  
long periods of storage, battery cables should be dis-  
connected and battery cleaned thoroughly (see “TO  
CLEAN BATTERY AND TERMINALS” in the Mainte-  
nance section of this manual).  
•
•
Turn ignition key to “START”position for a few seconds  
to distribute oil.  
Replace with new spark plug(s).  
•
•
After cleaning, leave cables disconnected and place  
cables where they cannot come in contact with battery  
terminals.  
If battery is removed from tractor for storage, do not  
store battery directly on concrete or damp surfaces.  
OTHER  
•
•
Do not store gasoline from one season to another.  
Replace your gasoline can if your can starts to rust.  
Rust and/or dirt in your gasoline will cause problems.  
•
•
If possible, store your tractor indoors and cover it to  
give protection from dust and dirt.  
Cover your tractor with a suitable protective cover that  
does not retain moisture. Do not use plastic. Plastic  
cannot breathe which allows condensation to form and  
will cause your tractor to rust.  
IMPORTANT: NEVERCOVERTRACTORWHILEENGINE AND  
EXHAUST AREAS ARE STILL WARM.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING POINTS  
PROBLEM  
CAUSE  
CORRECTION  
Will not start  
1. Out of fuel.  
1. Fill fuel tank.  
2. Engine not “CHOKED” properly.  
3. Engine flooded.  
4. Bad spark plug.  
5. Dirty air filter.  
2. See “TO START ENGINE” in Operation section.  
3. Wait several minutes before attempting to start.  
4. Replace spark plug.  
5. Clean/replace air filter.  
6. Dirty fuel filter.  
6. Replace fuel filter.  
7. Water in fuel.  
7. Empty fuel tank and carburetor, refill tank with fresh  
gasoline and replace fuel filter.  
8. Loose or damaged wiring.  
8. Check all wiring.  
9. Carburetor out of adjustment.  
9. See “To Adjust Carburetor” in Service Adjustments  
section.  
10. Engine valves out of adjustment.  
10. Contact an authorized service center/department.  
Hard to start  
1. Dirty air filter.  
1. Clean/replace air filter.  
2. Bad spark plug.  
2. Replace spark plug.  
3. Weak or dead battery.  
4. Dirty fuel filter.  
3. Recharge or replace battery.  
4. Replace fuel filter.  
5. Stale or dirty fuel.  
6. Loose or damaged wiring.  
7. Carburetor out of adjustment.  
5. Empty fuel tank and refill tank with fresh, clean gasoline.  
6. Check all wiring.  
7. See “To Adjust Carburetor” in Service Adjustments  
section.  
8. Engine valves out of adjustment.  
8. Contact an authorized service center/department.  
Engine will not turn over  
1. Brake pedal not depressed.  
2. Attachment clutch is engaged.  
3. Weak or dead battery.  
1. Depress brake pedal.  
2. Disengage attachment clutch.  
3. Recharge or replace battery.  
4. Replace fuse.  
4. Blown fuse.  
5. Corroded battery terminals.  
6. Loose or damaged wiring.  
7. Faulty ignition switch.  
8. Faulty solenoid or starter.  
9. Faulty operator presence switch(es).  
5. Clean battery terminals.  
6. Check all wiring.  
7. Check/replace ignition switch.  
8. Check/replace solenoid or starter.  
9. Contact an authorized service center/department.  
Engine clicks but will not  
start  
1. Weak or dead battery.  
1. Recharge or replace battery.  
2. Clean battery terminals.  
3. Check all wiring.  
2. Corroded battery terminals.  
3. Loose or damaged wiring.  
4. Faulty solenoid or starter.  
4. Check/replace solenoid or starter.  
Loss of power  
1. Cutting too much grass/too fast.  
2. Throttle in “CHOKE” position.  
3. Build-up of grass, leaves and trash under mower.  
4. Dirty air filter.  
1. Raise cutting height/reduce speed.  
2. Adjust throttle control.  
3. Clean underside of mower housing.  
4. Clean/replace air filter.  
5. Low oil level/dirty oil.  
6. Faulty spark plug.  
7. Dirty fuel filter.  
5. Check oil level/change oil.  
6. Clean and regap or change spark plug.  
7. Replace fuel filter.  
8. Stale or dirty fuel.  
9. Water in fuel.  
8. Empty fuel tank and refill tank with fresh, clean gasoline.  
9. Empty fuel tank and carburetor, refill tank with fresh  
gasoline and replace fuel filter.  
10. Spark plug wire loose.  
11. Dirty engine air screen/fins.  
12. Dirty/clogged muffler.  
10. Connect and tighten spark plug wire.  
11. Clean engine air screen/fins.  
12. Clean/replace muffler.  
13. Loose or damaged wiring.  
14. Carburetor out of adjustment.  
13. Check all wiring.  
14. See “To Adjust Carburetor” in Service Adjustments  
section.  
15. Engine valves out of adjustment.  
15. Contact an authorized service center/department.  
Excessive vibration  
1. Worn, bent or loose blade.  
2. Bent blade mandrel.  
1. Replace blade. Tighten blade bolt.  
2. Replace blade mandrel.  
3. Loose/damaged part(s).  
3. Tighten loose part(s). Replace damaged parts.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING POINTS  
PROBLEM  
CAUSE  
CORRECTION  
Engine continues to run  
when operator leaves seat  
with attachment clutch  
engaged  
1. Faulty operator-safety presence control system.  
1. Check wiring, switches and connections. If not  
corrected, contact an authorized service center/  
department.  
Poor cut - uneven  
1. Worn, bent or loose blade.  
2. Mower deck not level.  
1. Replace blade. Tighten blade bolt.  
2. Level mower deck.  
3. Buildup of grass, leaves, and trash under mower.  
4. Bent blade mandrel.  
3. Clean underside of mower housing.  
4. Replace blade mandrel.  
5. Clogged mower deck vent holes from buildup of  
grass, leaves, and trash around mandrels.  
5. Clean around mandrels to open vent holes.  
Mower blades will not  
rotate  
1. Obstruction in clutch mechanism.  
2. Worn/damaged mower drive belt.  
3. Frozen idler pulley.  
1. Remove obstruction.  
2. Replace mower drive belt.  
3. Replace idler pulley.  
4. Frozen blade mandrel.  
4. Replace blade mandrel.  
Poor grass discharge  
1. Engine speed too slow.  
2. Travel speed too fast.  
1. Place throttle control in “FAST” position.  
2. Shift to slower speed.  
3. Wet grass.  
4. Mower deck not level.  
3. Allow grass to dry before mowing.  
4. Level mower deck.  
5. Low/uneven tire air pressure.  
6. Worn, bent or loose blade.  
7. Buildup of grass, leaves and trash under mower.  
8. Mower drive belt worn.  
5. Check tires for proper air pressure.  
6. Replace/sharpen blade. Tighten blade bolt.  
7. Clean underside of mower housing.  
8. Replace mower drive belt.  
9. Blades improperly installed.  
10. Improper blades used.  
11. Clogged mower deck vent holes from buildup of  
grass, leaves, and trash around mandrels.  
9. Reinstall blades sharp edge down.  
10. Replace with blades listed in this manual.  
11. Clean around mandrels to open vent holes.  
Headlight(s) not working  
(if so equipped)  
1. Switch is “OFF”.  
1. Turn switch “ON”.  
2. Bulb(s) or lamp(s) burned out.  
3. Faulty light switch.  
4. Loose or damaged wiring.  
5. Blown fuse.  
2. Replace bulb(s) or lamp(s).  
3. Check/replace light switch.  
4. Check wiring and connections.  
5. Replace fuse.  
Battery will not charge  
Loss of drive  
1. Bad battery cell(s).  
1. Replace battery.  
2. Poor cable connections.  
3. Faulty regulator (if so equipped).  
4. Faulty alternator.  
2. Check/clean all connections.  
3. Replace regulator.  
4. Replace alternator.  
1. Freewheel control in “disengaged” position.  
2. Motion drive belt worn, damaged, or broken.  
3. Air trapped in transmission during shipment  
or servicing.  
1. Place freewheel control in “engaged” position.  
2. Replace motion drive belt.  
3. Purge transmission.  
Engine “backfires” when  
turning engine “OFF”  
1. Engine throttle control not set between half and  
full speed (fast) position before stopping engine.  
1. Move throttle control between half and full speed  
(fast) position before stopping engine.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE NOTES  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO.YTH2248 (YTH2248A), PRODUCT NO. 954 57 19-77  
SCHEMATIC  
RED  
BLACK  
BATTERY  
FUSE  
SOLENOID  
RED  
RED  
RED  
M
A
STARTER  
BLACK  
AMMETER  
(OPTIONAL)  
WHITE  
WHITE  
BLACK  
WHITE  
RED  
C
G
H
S
ELECTRIC CLUTCH  
B
M
CLUTCH / BRAKE  
(PEDAL UP)  
RED  
G
A1  
F
L
A2  
B
A
RED  
IGNITION  
SWITCH  
BLACK  
E
85  
87  
86  
30  
BLACK  
SEAT SWITCH  
(NOT OCCUPIED)  
D
PTO (DISENGAGED)  
87A  
GREEN  
GREEN  
OPERATOR  
PRESENCE  
RELAY #1  
HOUR  
METER  
BLACK  
BLUE  
FUEL  
LINE  
(OPTIONAL)  
SPARK  
BLACK  
IGNITION  
UNIT  
PLUGS GAP  
(2 PLUGS ON  
BLUE  
TWIN CYL. ENGINES)  
FUEL SHUT-OFF SOLENOID  
CHARGING SYSTEM OUTPUT  
15 AMP DC @ 3600 RPM  
28 VOLTS AC @ 3600 RPM  
(REGULATOR DISCONNECTED)  
RED  
REGULATOR  
ALTERNATOR  
BROWN  
BLACK  
WIRING INSULATED CLIPS  
NOTE: IF WIRING INSULATED  
CLIPS WERE REMOVED FOR  
SERVICING OF UNIT, THEY  
SHOULD BE REPLACED TO  
PROPERLY SECURE YOUR WIRING.  
HEADLIGHTS  
G F C  
PTO SWITCH  
87  
IGNITION SWITCH  
E
H
B
POSITION  
CIRCUIT  
87A  
POSITION CIRCUIT “MAKE”  
86  
85  
OFF  
ON  
C + G, B + H  
C + F, B + E, A + D  
OFF  
RUN/LIGHT  
M+G+A1  
B+A1  
NONE  
A2+L  
30  
RELAY  
A
D
RUN  
B+A1  
NONE  
REMOVABLE  
CONNECTIONS  
START B + S + A1 NONE  
NON-REMOVABLE  
CONNECTIONS  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - MODEL NO.YTH2248 (YTH2248A), PRODUCT NO. 954 57 19-77  
ELECTRICAL  
22  
21  
42  
24  
40  
26  
16  
33  
30  
50  
D
.C  
.
A
M
P
E
R
E
S
89  
10  
27  
46  
29  
45  
11  
55  
28  
12  
2
1
8
12  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - MODEL NO.YTH2248 (YTH2248A), PRODUCT NO. 954 57 19-77  
ELECTRICAL  
KEY PART  
NO. NO.  
DESCRIPTION  
1
532 14 49-27 Battery 12 Volt 35 AMP  
874 76 04-12 Bolt Hex Hd 1/4-20 unc x 3/4  
532 12 48-86 Tray Battery  
2
8
10  
11  
12  
16  
21  
22  
24  
26  
27  
28  
29  
30  
33  
40  
42  
45  
46  
50  
55  
89  
532 14 52-11 Bolt Brt Frt 1/4-20 x 75 Ainc  
532 15 01-09 Holddown Battery Front Mount  
532 14 57-69 Nut Push Nylon 1/4" Battery Frt  
532 17 61-38 Switch Interlock  
532 18 37-59 Harness Asm Light W/4152j  
532 00 41-52 Bulb Light #1156  
532 17 89-09 Cable Battery  
532 17 51-58 Fuse  
873 51 04-00 Nut Keps Hex 1/4-20 unc  
532 14 54-91 Cable Ground 6 Ga 21" black  
532 12 13-05 Switch Plunger Nc Gray  
532 17 55-66 Switch Ign  
532 14 04-01 Key Ign Molded Generic  
532 18 80-27 Harness Ign.  
532 15 43-36 Cover Terminal Red  
532 12 28-22 Ammeter Rectangular 15 Amp  
532 16 96-35 Meter Hour  
532 17 46-51 Switch PTO  
817 49 05-08 Screw Thdrol 5/16-18 x 1-1/2 Tyt  
532 16 96-39 Bracket Snap-In Hourmeter  
NOTE: All component dimensions given in U.S. inches.  
1 inch = 25.4 mm.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - MODEL NO.YTH2248 (YTH2248A), PRODUCT NO. 954 57 19-77  
CHASSIS AND ENCLOSURES  
259  
212  
258  
28  
212  
17  
213  
10  
39  
217  
277  
276  
10  
278  
30  
214  
58  
90  
31  
209  
159  
219  
280  
20  
23  
11  
208  
9
280  
209  
53  
166  
158  
55  
209  
219  
166  
64  
209  
1
144  
209  
13  
26  
26  
60  
142  
143  
144  
60  
26  
26  
142  
145  
37  
37  
209  
2
14  
208  
74  
38  
209  
14  
38  
chassis_elite husqy_3  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - MODEL NO.YTH2248 (YTH2248A), PRODUCT NO. 954 57 19-77  
CHASSIS AND ENCLOSURES  
KEY PART  
NO. NO.  
DESCRIPTION  
1
532 17 46-19 Chassis Stamping  
532 17 65-54 Drawbar  
532 19 02-51 Dash  
2
9
10  
11  
13  
14  
17  
20  
23  
26  
28  
30  
31  
37  
38  
39  
53  
55  
58  
60  
64  
74  
90  
872 14 06-08 Bolt Rdhd Sqnk 3/8-16 unc x 1  
532 17 49-96 Panel Dash Lh  
532 17 21-06 Panel Dash Rh  
817 49 06-08 Screw Thdrol 3/8-16 x 1/2  
532 18 99-77 Hood  
532 18 06-79 Plate Mtg Battery/Fuel Tank  
532 12 40-28 Bushing  
873 80 06-00 Nut Lock w/Insert 3/8-16 unc  
532 18 82-69 Grille Lens Asm (Includes Key Nos. 212, 258 & 259)  
532 18 54-32 Fender  
532 13 99-76 Bracket  
817 49 05-08 Screw Thdrol 5/16-18 x 1/2  
532 17 57-10 Bracket Asm Pivot Mower Rear  
532 17 47-14 Bracket Pivot  
532 18 83-72 Bracket Dash RH  
532 18 83-73 Bracket Dash LH  
532 18 44-63 Duct Air  
872 14 06-06 Bolt RDHD SQNK 3/8-16 x 3/4  
532 17 49-97 Dash Lower  
873 68 06-00 Nut Crownlock 3/8-16  
532 12 43-46 Nut 1/4  
142 532 17 57-02 Plate Reinforcement  
143 532 18 66-89 Bracket Swaybar Chassis  
144 532 17 55-82 Bracket Ft Rest  
145 532 15 65-24 Rod Pivot Chassis Hood  
158 532 16 20-37 Bracket Parking Brake  
159 532 18 54-34 Cupholder  
166 532 17 18-75 Screw HwHd Hi-Lo #13-16 x 3/4  
208 817 67 06-08 Screw Thdrol 3/8-16 x 1/2 Ty-TT  
209 817 00 06-12 Screw 3/8-16 x 3/4  
212 532 18 82-67 Lens Insert Reflect  
213 532 18 99-79 Skirt Side LH  
214 532 18 99-78 Skirt Side RH  
217 532 18 54-36 Console Fuel Window  
219 817 00 05-12 Screw 5/16-18 x 3/4  
258 532 18 99-81 Lens RH  
259 532 18 99-82 Lens LH  
276 532 18 92-74 Bumper Hood RH  
277 532 18 92-75 Bumper Hood LH  
278 532 18 95-85 Screw Quadx WSHD #10-14 x 1  
280 817 06 06-16 Screw 3/8-16 x 1  
NOTE: All component dimensions given in U. S. inches.  
1 inch = 25.4 mm  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - MODEL NO.YTH2248 (YTH2248A), PRODUCT NO. 954 57 19-77  
DRIVE  
57  
120  
89  
63  
116  
23  
212  
66  
90  
59  
197  
159  
158  
162  
56  
61  
161  
9
169  
10  
202  
198  
65  
17  
50  
41  
38  
83  
150  
48  
14  
81  
20  
112  
168  
163  
21  
27  
49  
151  
51  
82  
166  
156  
165  
52  
35  
39  
8
47  
32  
30  
62  
120  
34  
36  
52  
37  
36  
35  
32  
16  
95  
53  
28  
30  
26  
84  
55  
16  
29  
22  
27  
16  
19  
199  
24  
77  
25  
26 26  
200  
263  
263  
71  
15  
77  
74  
73  
96  
16  
75  
78  
1
76  
drive-fender.stlt_58  
26  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - MODEL NO.YTH2248 (YTH2248A), PRODUCT NO. 954 57 19-77  
DRIVE  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
1
- - - - - - - -  
Transaxle, Hydro 314-0510  
(Order Parts From Transaxle Manu-  
facturer)  
63  
65  
66  
71  
73  
74  
75  
76  
77  
78  
81  
82  
83  
84  
89  
90  
95  
96  
532 17 46-07 Pulley, Engine  
810 04 07-00 Washer Lock Hvy HLCL Spr 7/16  
532 15 47-78 Keeper Belt Engine  
532 16 91-83 Strap Torque Lh Hydro  
532 16 91-82 Strap Torque Rh Hydro  
532 13 70-57 Spacer, Axle  
8
9
532 16 58-66 Rod Shift Fender Adjust STLT  
532 17 93-34 Clutch Elecric  
876 02 04-16 Pin Cotter 1/8 x 1 CAD  
810 04 04-00 Washer Lock Hvy Helical  
874 49 05-44 Bolt Hex 5/16-18 Unc Flghd  
873 80 05-00 Nut Lock Hex W/Ins. 5/16-18 unc P  
532 12 61-97 Washer  
873 80 06-00 Nut Lock Hex W/Ins 3/8-16 unc  
532 17 39-37 Bolt, Hex 7/16-20 x 4-1/4 Ga. 5  
532 14 08-45 Knob Deluxe 1/2-13 unc BLK/BLK  
532 16 94-98 Rod, Brake Hydro  
532 17 82-89 Bracket Asm Mtg CL  
873 35 06-00 Nut Hex Jam 3/8-16 unc  
532 10 68-88 Spring, Brake Rod  
819 13 13-16 Washer  
10  
14  
15  
16  
17  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
32  
34  
35  
36  
37  
38  
39  
41  
47  
48  
49  
50  
51  
52  
53  
55  
56  
57  
59  
61  
62  
532 12 17-49 Washer 25/32 x 1-1/4 x 16 Ga.  
812 00 00-01 E-Ring  
532 12 35-83 Key, Square  
532 12 17-48 Washer 25/32 x 1-5/8 x 16 Ga.  
532 16 55-96 Shaft Asm Cross Tapered  
532 16 57-11 Spring Torsion T/A  
819 17 12-16 Washer 17/32 x 3/4 x 16 Ga.  
532 16 95-94 Link Transaxle  
532 16 65-10 Console, Shift  
532 12 43-46 Nut Self Thd 1/4  
532 17 02-01 Control Asm. Bypass Hydro  
532 12 47-88 Retainer Spring 1" Zinc/Cad  
876 02 04-12 Pin Cotter 1/8 x 3/4 CAD.  
532 17 57-65 Rod, Parking Brake  
532 07 16-73 Cap,Parking Brake  
532 16 95-92 Bracket, Transaxle  
874 76 05-12 Bolt Hex Hd 5/16-18 unc x 3/4  
532 17 55-78 Shaft, Foot Pedal  
112 819 09 12-10 Washer 9/32 x 3/4 x 10 Ga.  
116 872 14 06-08 Bolt Rdhd Sqnk 3/8-16 unc x 1  
120 873 90 06-00 Nut Lock Flg 3/8-16  
150 532 17 54-56 Spacer Retainer  
151 819 13 32-10 Washer 13/32 x 2 x 10 Ga.  
156 532 16 60-02 Washer Srrted 5/16ID x 1.125  
158 532 16 55-89 Bracket Shift Mount  
532 12 01-83 Bearing, Nylon  
819 21 16-16 Washer  
159 532 18 39-00 Hub Shift  
532 12 49-63 Pin, Roll  
161 872 14 04-06 Bolt Rdhd Sqnk 1/4-20 x 3/4 Gr. 5  
162 873 68 04-00 Nut Crownlock 1/4-20 unc  
163 874 78 04-16 Bolt Hex Fin 1/4-20 unc x 1 Gr. 5  
165 532 16 56-23 Bracket Pivot Lever  
532 17 91-14 Pulley, Composite  
872 11 06-22 Bolt, RDHD 3/8-16 unc x 2-3/4 Gr. 5  
532 17 55-56 Keeper, Belt Idler  
532 12 77-83 Pulley, Idler, V-Groove Plastic  
532 15 44-07 Bellcrank Clutch Grnd Drv STL  
532 12 32-05 Retainer, Belt Style Spring  
872 11 06-12 Bolt 3/8-16 x 1-1/2 Gr. 5  
873 68 06-00 Nut  
873 68 05-00 Nut Crownlock 5/16-18  
532 10 57-10 Link, Clutch  
532 10 57-09 Spring, Return, Clutch  
817 06 06-20 Screw 3/8-16 x 1-1/4  
532 14 02-94 V-Belt, Ground Drive  
532 16 96-91 Keeper, Center Span  
817 12 06-14 Screw 3/8-16 x .875  
532 12 48-72 Cover, Pedal  
166 817 49 05-10 Screw 5/16-18 x 5/8  
168 532 16 54-92 Bolt Shoulder 5/16-18 x .561  
169 532 16 55-80 Plate Fastening STLT/CRD  
197 532 16 96-13 Nyliner Snap 5/8" ID  
198 532 16 95-93 Washer Nyl 7/8 ID x .105 Hyd  
199 532 16 96-12 Bolt Shoulder 5/16-18 unc  
200 872 14 05-08 Bolt Rdhd Sqnk 5/16-18 unc x 1  
202 872 11 06-14 Bolt 3/8-16 x 1-3/4 Gr. 5  
212 532 14 52-12 Nut Hex Flange Lock  
263 817 00 06-12 Screw 3/8-16 x 3/4  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - MODEL NO.YTH2248 (YTH2248A), PRODUCT NO. 954 57 19-77  
STEERING ASSEMBLY  
38  
12  
39  
1
41  
37  
37  
36  
88  
91  
43  
71  
67  
67  
68  
46  
8
29  
67  
13  
6
65  
17  
46  
2
8
6
87  
5
87  
3
32  
5
68  
11  
4
29  
43  
82  
40  
43  
95  
8
94  
15  
29  
15  
11  
40  
15  
10  
steering_pl.lt_54  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - MODEL NO.YTH2248 (YTH2248A), PRODUCT NO. 954 57 19-77  
STEERING ASSEMBLY  
KEY PART  
NO. NO.  
DESCRIPTION  
1
532 16 66-27 Wheel Steering  
2
532 18 47-06 Axle Asm  
3
532 16 98-40 Spindle Asm LH  
532 16 98-39 Spindle Asm RH  
532 12 49-31 Bearing Race Thrust Harden  
532 12 17-48 Washer 25/32 x 1-5/8 x 16 Ga.  
812 00 00-29 Ring Klip #t5304-75  
532 17 51-21 Link Drag  
4
5
6
8
10  
11  
12  
13  
15  
17  
29  
32  
36  
37  
38  
39  
40  
41  
43  
46  
65  
67  
68  
71  
82  
87  
88  
91  
94  
95  
810 04 06-00 Washer Lock Hvy Hlcl Spr 3/8  
873 94 08-00 Nut Hex Jam Toplock 1/2-20 unf  
532 13 65-18 Spacer Brg Axle Front  
532 14 52-12 Nut Hex Flange Lock  
532 17 78-83 Shaft Asm Strg  
817 00 06-12 Screw 3/8-16 x 3/4  
532 18 05-80 Rod Tie Ball J  
532 15 51-05 Bushing Strg  
532 15 29-27 Screw  
532 16 66-26 Insert Cap Strg Wh  
819 18 38-12 Washer 9/16 x 2-3/8  
873 54 06-00 Nut Crownlock 3/8-24  
532 15 99-45 Adaptor Wheel Strg  
532 12 17-49 Washer 25/32 x 1 1/4 x 16 Ga.  
532 12 12-32 Cap Spindle Fr Top Blk  
532 16 03-67 Spacer Brace Axle  
872 11 06-18 Bolt RDHD SQNK 3/8-16 x 2-1/4  
532 16 98-27 Axle, Brace  
532 17 51-46 Steering Asm  
532 16 98-35 Bracket Susp Chassis Front  
532 17 39-66 Washer Flat .781 x 1-1/2 x .14  
532 17 51-18 Bolt Shoulder 7/16-20  
532 17 55-53 Clip Steering  
819 12 14-14 Washer 3/8 x 7/8 x 14 Ga.  
532 18 89-67 Washer Hardened  
NOTE: All component dimensions given in U.S. inches.  
1 inch = 25.4 mm.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - MODEL NO.YTH2248 (YTH2248A), PRODUCT NO. 954 57 19-77  
SEAT ASSEMBLY  
1
8
9
8
9
14  
7
7
10  
5
6
22  
21  
2
24  
5
16  
25  
15  
11  
4
13  
17  
3
12  
seat_lt.knob_1  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
1
532 18 87-15 Seat  
13  
14  
15  
16  
17  
21  
22  
24  
25  
532 12 12-48 Bushing Snap Blk Nyl 50 Id  
872 05 04-12 Bolt Rdhd Sqnk 1/4-20 x 1-1/2  
532 12 12-49 Spacer Split 28 x .88 Zinc  
532 12 37-40 Spring Cprsn Plate  
532 12 39-76 Nut Lock 1/4 Lge Flg Gr. 5 Zinc  
532 17 18-52 Bolt Shoulder 5/16-18 unc  
873 80 05-00 Nut Hex Lock W/ins 5/16-18  
819 17 19-12 Washer 17/32 x 1-3/16 x 12 Ga.  
532 12 70-18 Bolt Shoulder 5/16-18 x .62  
2
532 14 05-51 Bracket Pivot Seat 8 720  
871 11 06-16 Bolt Fin Hex 3/8-16 x 1  
819 13 16-10 Washer Flat 13/32 x 1.0 x 10 Ga.  
532 14 50-06 Clip Push-In  
3
4
5
6
873 80 06-00 Nut Hex w/Ins. 3/8-16 unc  
532 12 41-81 Spring Seat Cprsn 2 250 Blk Zi  
817 00 06-16 Screw 3/8-16 x 1  
819 13 16-14 Washer 13/32 x 1.0 x 14 Ga.  
532 18 24-93 Pan Seat  
532 16 63-69 Knob Seat  
532 12 12-46 Bracket Mounting Switch  
7
8
9
10  
11  
12  
NOTE: All component dimensions given in U.S. inches.  
1 inch = 25.4 mm  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - MODEL NO.YTH2248 (YTH2248A), PRODUCT NO. 954 57 19-77  
DECALS  
7,13  
11  
4
11  
3
2
10  
5
1
8
20  
14  
17  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
13  
14  
17  
20  
- -  
- -  
- -  
- -  
- -  
532 18 09-41 Decal Cust. Responsibilities  
532 17 52-91 Decal V-Belt Schematic  
532 17 84-82 Decal, Mower  
532 14 50-05 Decal Bat Dan/Psn  
532 16 69-60 Decal By Pass  
532 18 82-52 Pad Footrest LH  
532 18 82-53 Pad Footrest RH  
532 13 83-11 Decal Handle Lft Height Adjust  
532 18 99-07 Manual Owner's (English)  
1
532 15 70-32 Decal Oper Inst Hyd E/F  
532 18 89-25 Decal Strg Wheel Logo  
532 18 89-18 Decal Hood RH  
532 18 89-19 Decal Hood LH  
2
3
4
5
532 18 92-43 Decal Dash  
7
532 18 96-72 Decal Repl. Parts  
532 17 05-63 Decal Warning  
532 15 71-40 Decal Fender Danger E/F  
532 18 94-49 Decal Hood Sides  
8
10  
11  
KEY PART  
NO. NO.  
WHEELS & TIRES  
DESCRIPTION  
1
532 05 91-92 Cap Valve Tire  
1
2
532 06 51-39 Stem Valve  
2
5,8  
3
532 10 62-22 Tire F Ts 15 x 6 0 - 6 Service  
532 05 99-04 Tube Front (Service Item Only)  
532 13 83-36 Rim Asm 6" front Silver Service  
532 12 49-57 Fitting Grease (Front Wheel Only)  
532 12 49-59 Bearing Flange (Front Wheel Only)  
532 13 83-37 Rim Asm 8" rear Silver Service  
532 12 20-82 Tire R Ts 20 x 10-8 C Service  
532 12 49-26 Tube Rear (Service Item Only)  
532 17 50-39 Cap Axle Blk 1 50 x 1 00  
532 14 43-34 Sealant, Tire ( 10 oz. Tube)  
4
4,10  
5
7
6
3,9  
7
8
6
11  
9
10  
11  
- -  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
wheel_1  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - MODEL NO.YTH2248 (YTH2248A), PRODUCT NO. 954 57 19-77  
ENGINE  
3
2
8
1
38  
10  
13  
17  
101  
25  
14  
6
17  
26  
5
116  
17  
32  
31  
33  
37  
41  
112  
33  
45  
29  
23  
OPTIONAL EQUIPMENT  
Spark Arrester  
4
engine-ko.twin_15  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
33  
37  
38  
41  
45  
532 12 34-87 Clamp Hose Blk  
532 14 21-58 Line Fuel  
1
2
3
532 19 02-59 Control Throttle  
817 72 04-08 Screw Hex Thd Cut 1/4-20 x 1/2  
Engine Kohler CV674 (Order Parts  
from Engine Manufacturer)  
532 14 97-23 Muffler Asm Twin Lo-Tone  
532 14 66-99 Exhaust Tube LH  
532 14 67-00 Exhaust Tube RH  
532 18 16-54 Plug Drain Oil  
- - - - - - - -  
532 13 92-77 Stem Tank Fuel  
817 00 06-12 Screw Hexwsh Thdr 3/8-16 x 3/4  
4
101 532 16 33-05 Nut Flange M8-1.25  
112 532 12 49-52 Bushing  
116 532 18 43-62 Nut Hex Flange Toplock M8-1.25  
5
6
8
532 17 18-77 Bolt 5/16-18 Unc x 3/4 W/Sems  
532 14 66-29 Shield Browning  
10  
13  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
For engine service and replacement parts, call the toll free  
number for your engine manufacturer listed below:  
Briggs & Stratton  
Kohler Co.  
Tecumseh Products  
Honda Engines  
Kawasaki  
- - - - - - - -  
Gasket Muffler  
(Order from Engine Manufacturer)  
14  
17  
23  
25  
26  
29  
31  
32  
532 14 84-56 Tube Drain Oil Easy  
817 06 06-24 Screw 3/8-16 x 1-1/2  
532 16 98-37 Shield Browning  
532 19 02-60 Choke Control  
1-800-233-3723  
1-800-544-2444  
1-800-558-5402  
1-800-426-7701  
1-800-460-5688  
873 92 06-00 Nut, Keps 3/8-24 unf  
532 13 71-80 Kit Spark Arrestor (Flat Scrn)  
532 17 90-22 Tank Fuel  
532 18 18-03 Cap Asm Fuel  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - MODEL NO.YTH2248 (YTH2248A), PRODUCT NO. 954 57 19-77  
MOWER LIFT  
29  
28  
27  
25  
24  
23  
7
8
41  
5
49  
37  
38  
30  
50  
40  
1
4
3
36  
13  
4
26  
13  
6
2
6
5
11  
12  
13  
51  
49  
52  
31  
13  
51  
32  
53  
49  
20  
32  
13  
18  
54  
17  
16  
15  
13  
lift-rh.1pc.stlt_2  
54  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
27  
28  
29  
30  
31  
32  
36  
37  
38  
40  
41  
49  
50  
51  
52  
53  
54  
532 12 69-71 Rod Adj Lift Zinc 7.49 Wrk Lg  
873 35 06-00 Nut Hex Jam 3/8-16 unc  
532 13 80-57 Knob Inf 3/8-16 Unc Blk W/sym  
532 15 02-33 Trunnion Infin Height  
532 17 62-05 Trunnion  
532 17 59-94 Nut Lift Link 7/16-20  
532 15 50-97 Indicator Height STLT  
532 12 39-35 Plug Hole Blk 1.485/1.515 Dia.  
817 06 05-16 Screw 5/16-18 x 1  
819 11 24-10 Washer 11/32 x 1-1/2 10 Ga.  
532 15 50-98 Scale Ind. Height Blk.  
532 14 52-12 Nut Hex Flange Lock  
532 11 04-52 Nut, Push Phos & Oil  
819 17 14-16 Washer 17/32 x 7/8 x 16 Ga.  
532 17 53-78 Arm Susp. Rear Lh  
532 17 58-02 Arm Susp. Rear Rh  
532 17 55-60 Pin Flange  
1
532 15 94-60 Wire Asm Inner/Spring W/Plunger LT  
532 15 94-71 Shaft Asm Lift RH w/Inf  
532 10 57-67 Pin Groove 1 500 Zinc  
812 00 00-02 E Ring #5133-62  
819 21 16-21 Washer 21/32 x 1 x 21 Ga  
532 12 01-83 Bearing Nylon Blk 629 Id  
532 12 56-31 Grip Handle Fluted Blk  
532 12 45-26 Button Plunger Black  
532 17 53-70 Link Lift LH  
2
3
4
5
6
7
8
11  
12  
13  
15  
16  
17  
18  
20  
23  
24  
25  
26  
532 17 53-71 Link Lift RH  
532 12 46-70 Retainer Spring  
532 17 55-62 Plate Asm Susp Front  
873 35 08-00 Nut Jam Hex 1/2-13 unc  
532 17 56-89 Trunnion  
873 80 08-00 Nut Lock w/Wsh 1/2-13 unc  
532 16 35-52 Retainer Spring  
532 11 08-07 Nut Special  
819 13 10-16 Washer 13/32 x 5/8 x 16 Ga.  
532 12 48-74 Spring 2-1/8"  
532 16 94-84 Retainer Clip  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - MODEL NO.YTH2248 (YTH2248A), PRODUCT NO. 954 57 19-77  
MOWER DECK  
46  
132  
95  
182  
45  
49  
94  
183  
46  
52  
49  
30  
91  
132  
37  
33  
45  
47  
130  
42  
32  
33  
43  
30  
31  
49  
121  
98  
42  
49  
39  
32  
126  
99  
50  
30  
50  
97  
97  
111  
31  
21  
131  
110  
5
21  
57  
56  
116  
117  
184  
113  
118  
119  
100  
55  
24  
25  
21  
16  
18  
92  
54  
72  
1
26  
92  
28  
3
29  
17  
6
27  
5
15  
19  
14  
20  
13  
18  
11  
48  
8
mower_deck.48_standard_1  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - MODEL NO.YTH2248 (YTH2248A), PRODUCT NO. 954 57 19-77  
MOWER DECK  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
1
532 18 03-58 Deck Weldment Mower 48  
532 13 80-17 Bracket Asm., Sway Bar  
532 12 46-70 Retainer Spring  
54  
55  
56  
57  
72  
91  
92  
94  
95  
97  
98  
99  
874 78 06-16 Bolt Fin Hex 3/8-16 x 1  
872 14 06-08 Bolt Rdhd Sqnk 3/8-16 x 1  
532 15 59-86 Bar Pnt Adjusting Wheel Gauge  
532 15 69-41 Pin Head Rivet  
819 13 13-12 Washer 13/32 x 13/16 x 12  
532 18 05-35 Bracket, Asm Noseroller, RH 48  
873 80 06-00 Nut Lock Hex w/Ins 3/8-16  
532 17 60-66 Roller, Nose 48"  
532 18 05-34 Bracket, Asm Noseroller LH 48  
532 17 85-15 Washer Hardened  
532 17 94-79 Spring Primary Drive  
532 18 40-58 Pulley Idler "V"  
3
5
6
532 17 80-24 Bar Sway Deck  
8
532 17 43-65 Bolt, 7/16 Asm. Blade  
532 18 00-54 Blade  
532 17 51-47 Shaft Asm. Mandrel Sealed  
532 17 43-58 Housing Mandrel 48"  
532 11 04-85 Bearing, Ball, Mandrel  
532 17 44-93 Stripper, Mower  
872 11 06-10 Bolt Rdhd Sq Neck 3/8-16 x 1.25  
872 14 05-05 Bolt, Carriage 5/16-18 x 5/8  
532 13 28-27 Bolt, Hex Head, Shoulder 5/16-18  
532 17 43-78 Baffle, Vortex Mower  
873 68 05-00 Nut, Crownlock 5/16-18 unc  
532 10 53-04 Cap, Sleeve  
11  
13  
14  
15  
16  
17  
18  
19  
20  
21  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
37  
39  
42  
43  
45  
46  
47  
48  
49  
50  
52  
100 872 11 06-16 Bolt RDHD Sqnk 3/8-16 unc x 2  
110 532 17 50-16 Arm Spring Secondary  
111 532 17 46-10 Arm Spring Fixed Tension  
113 872 11 05-06 Bolt RdhdSqnk 5/16-18 unc x 3/4  
116 532 18 42-19 Bolt, Shoulder  
532 17 81-02 Spring, Torsion  
532 11 04-52 Nut, Push  
117 532 13 39-57 Gauge Wheel  
532 18 17-07 Shield, Deflector Mower  
819 11 10-16 Washer 11/32 x 5/8 x 16 Ga.  
532 13 14-91 Rod, Hinge  
532 17 39-84 Screw, Thdroll, Washer Head  
532 18 76-90 Washer, Spacer Mower Vented  
532 17 78-65 Pulley, Mandrel  
532 17 83-42 Nut, Flg. Top Lock Cntr. 9/16  
532 17 79-68 Pulley, Idler, Flat  
532 17 43-75 Pulley, Idler, Driven  
532 12 20-52 Spacer, Retainer  
532 17 43-73 Arm, Idler Secondary  
532 18 08-06 Cover, Mandrel Deck  
532 13 77-29 Screw, Thdroll. 1/4-20 x 5/8  
532 18 08-08 V-Belt, Mower, Secondary  
532 17 43-68 V-Belt, Mower, Primary  
873 90 06-00 Nut, Lock Flg. 3/8-16 unc  
872 11 06-12 Bolt, Carriage 3/8-16 x 1-1/2 Gr. 5  
532 17 58-20 Pulley Idler Flat 46 Pri. Drive  
118 873 93 06-00 Nut, Centerlock 3/8-16 unc  
119 819 12 14-14 Washer 3/8 x 7/8 x 14 Ga.  
121 532 17 43-71 Spring Secondary Drive  
126 532 17 43-72 Arm, Idler, Primary Deck  
130 817 00 06-16 Screw 3/8-16 x 1.0  
131 819 13 16-06 Washer 13/32 x 1 x 6 Ga.  
132 817 00 06-12 Screw Hexwsh Thdr. 3/8-16 x 3/4  
182 532 17 91-27 Rod Roller Nose  
183 532 16 35-52 Retainer Spring  
184 532 17 39-79 Keeper Belt Idler  
- -  
- -  
532 17 43-57 Mandrel Assembly (Includes Hous-  
ing, Shaft and Shaft Hardware  
Only-Pulley Not Included)  
532 18 99-06 Replacement Mower, Complete  
(Std. Deck-Order separately nose  
roller components key nos. 91, 94,  
95, 132, 182, 183)  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION  
FOLD ALONG DOTTED LINE  
THIS IS A 15 DEGREE SLOPE  
ONLY RIDE UP AND DOWN HILL,  
NOT ACROSS HILL  
15 DEGREES MAX.  
WARNING: To avoid serious injury, operate your tractor up and  
down the face of slopes, never across the face. Do not mow  
slopes greater than 15 degrees. Make turns gradually to prevent  
tipping or loss of control. Exercise extreme caution when  
changing direction on slopes.  
1. Fold this page along dotted line indicated above.  
2. Hold page before you so that its left edge is vertically parallel to a tree  
trunk or other upright structure.  
3. Sight across the fold in the direction of hill slope you want to measure.  
4. Compare the angle of the fold with the slope of the hill.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARRANTY STATEMENT  
01960_husqvarna  
SECTION 1: LIMITED WARRANTY  
SECTION 4: EXCEPTIONS AND LIMITATIONS  
Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original purchaser  
to be free from defects in material and workmanship from the date of purchase for the “Warranty Period” of the  
product as set forth below:  
This warranty shall be inapplicable to defects resulting from the following:  
(1)Accident, abuse, misuse, negligence and neglect, including stale fuel, dirt, abrasives, moisture, rust,  
corrosion, or any adverse reaction due to incorrect storage or use habits;  
(2)Failure to operate or maintain the unit in accordance with the Owner’s/Operator’s manual or instruc-  
tion sheet furnished by Husqvarna;  
Lifetime Warranty: All tiller tines against breakage, trimmer shafts, ignition coils and modules on hand held  
product.  
(3)Alterations or modifications that change the intended use of the product or affects the product’s per-  
formance, operation, safety, or durability, or causes the product to fail to comply with any applicable  
laws; or:  
3 Year Warranty: Spindles (on Zero Turn Riders and Commercial Walk-Behinds)  
2Year COMMERCIAL-Warranty: Husqvarna Commercial Turf Equipment—zero turn riders, wide area walks,  
and ground engaging commercial equipment.  
(4)Additional damage to parts or components due to continued use occurring after any of the above.  
2Year NON-COMMERCIAL Warranty: Automatic Mower, Riding lawn mowers, yard and garden tractors, walk  
behind mowers, tillers, chain saws, trimmers, brushcutters, clearing saws, snow blowers, handheld blowers,  
backpack blowers, hedge trimmers, electrical products and power-assist collection systems for noncom-  
mercial, nonprofessional, noninstitutional or nonincome producing use, except as herein stated.  
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF  
THE PURCHASER. HUSQVARNA SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL  
DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THESE PRODUCTS EXCEPT  
TO THE EXTENT PROHIBITED BY APPLICABLE LAW. ANY IMPLIED WARRANTY OF MERCHANTABIL-  
ITY OR FITNESS FOR A PARTICULAR PURPOSE ON THESE PRODUCTS IS LIMITED IN DURATION TO  
THE WARRANTY PERIOD AS DEFINED IN THE LIMITED WARRANTY STATEMENT. HUSQVARNA RE-  
SERVES THE RIGHT TO CHANGE OR IMPROVE THE DESIGN OF THE PRODUCT WITHOUT NOTICE,  
Emission control system components necessary to comply with CARB-TIER-II and EPA regulations, except  
for those components which are part of engine systems manufactured by third party engine manufacturers for  
which the purchaser has received a separate warranty with product information supplied at time of purchase.  
AND DOES NOT ASSUME OBLIGATION TO UPDATE PREVIOUSLY  
UCTS.  
MANUFACTURED PROD-  
1 Year Warranty: Power cutters, stump grinder, pole pruners and pole saws for non-commercial, non-pro-  
fessional, non-institutional or non-income producing use. All trimmers, brushcutters, clearing saws, hovering  
trimmers, stick edgers, backpack blowers, hand held blowers, hedge trimmers, power-assist collection systems  
used for commercial, institutional, professional or income producing purposes or use.  
Some states do not allow the exclusion of incidental or consequential damages, or limitations on how long  
an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives  
you specific legal rights, and you may also have other rights which vary from state to state.  
Batteries have a one-year prorated limited warranty with 100% replacement during the first 6 months.  
90 Day Warranty: Automatic Mower, Chain saws, power cutters, stump grinders, pole saws, pole pruners,  
snow throwers, model series 580 & 600 walk-behind mowers and commercial turf equipment or any Husqvarna  
product used for commercial, institutional, professional, or income producing purposes or use except as oth-  
erwise provided herein.  
SECTION 5: CUSTOMER RESPONSIBILITIES  
The product must exhibit reasonable care, maintenance, operation, storage and general upkeep as written  
in the maintenance section of the Owner’s/Operator’s manual. Should an operational problem or failure occur,  
the product should not be used, but delivered as is to an authorized Husqvarna dealer for evaluation. Proof  
of purchase, as explained in section 6, rests solely with the customer.  
Husqvarna Safety Apparel carries a 90-day warranty from the date of the customer’s original purchase for  
defects in material and workmanship. Normal wear, tear or abuse is not covered under warranty. Product must  
be returned to Charlotte with a warranty claim form. All care and maintenance instructions must be followed  
as stated by the manufacturer on the care label. The fit of the protective apparel/boot is not covered under  
warranty.  
SECTION 6: PROCEDURE TO OBTAIN WARRANTY CONSIDERATION  
It is the Owner’s and Dealer’s responsibility to make certain that the Warranty Registration Card is properly  
filled out and mailed to Husqvarna Forest & Garden Company.This card should be mailed within ten (10) days  
from the date of purchase in order to confirm the warranty and to facilitate post-sale service.  
30 Day Warranty: Replacement parts, accessories including bars and chains, tools and display items.  
SECTION 2: HUSQVARNA’S OBLIGATIONS UNDER THE WARRANTY  
Proof of purchase must be presented to the authorized Husqvarna dealer in order to obtain warranty ser-  
vice.This proof must include date purchased, model number, serial number, and complete name and address  
of the selling dealer.  
Husqvarna will repair or replace defective components without charge for parts or labor if a component fails  
because of a defect in material or workmanship during the warranty period.  
SECTION 3: ITEMS NOT COVERED BY THIS WARRANTY  
To obtain the benefit of this warranty, the product believed to be defective must be delivered to an au-  
thorized Husqvarna dealer in a timely manner, no later than thirty (30) days from date of the operational  
problem or failure. The product must be delivered at the owner’s expense. Pick-up and delivery charges are  
not covered by this warranty. An authorized Husqvarna dealer can be normally located through the “Yellow  
Pages” of the local telephone directory or by calling 1-800-HUSKY62 for a dealer in your area.  
The following items are not covered by this warranty:  
(1)Normal customer maintenance items which become worn through normal regular use, including, but  
not limited to, belts, blades, blade adapters, bulbs, filters, guide bars, lubricants, rewind springs, saw  
chain, spark plugs, starter ropes and tines;  
(2)Natural discoloration of material due to ultraviolet light;  
(3)Engine and drive systems not manufactured by Husqvarna; these items are covered by the respective  
manufacturer’s warranty as provided in writing with the product information supplied at the time of pur-  
chase; all claims must be sent to the appropriate manufacturer;  
(4)Lawn and garden attachments are covered by a third party which gives a warranty, all claims for war-  
ranty should be sent to the manufacturer; and  
HUSQVARNA  
7349 Statesville Road  
Charlotte, NC 28269  
531 83 81-23 2002  
(5)Emission Control System components necessary to comply with CARB-TIER-II and EPA regulations  
which are manufactured by third party engine manufacturer.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
532 18 99-07 Rev. 1 6.8.04 RD/MH  
Printed in U.S.A.  
01960_husqvarna  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Graco Baby Furniture ISPP062AA User Manual
Great Dane Lawn Mower GDRZ25KAE User Manual
Grizzly Saw G0717 User Manual
Hamilton Beach Coffeemaker D45012W User Manual
Harbor Freight Tools Chainsaw 67255 User Manual
HP Hewlett Packard Life Jacket 656830 004 User Manual
Huffy Fitness Equipment 211972B User Manual
Husky Nail Gun HDN104 User Manual
IDEAL INDUSTRIES Cooktop IZGS 68 ICTX User Manual
Impex Home Gym WM 3481 User Manual