06/03
P/N 211972B
1
© COPYRIGHT 2002 by HUFFY SPORTS
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE IDENTIFIER
Item #4 (1)
Item #8 (4)
Item #5 (1)
Item #10 (1)
Item #11 (12)
Item #13 (1)
Item #14 (2)
Item #12 (1)
Item #15 (20)*
Item #16 (1)
Item #19 (1)
Item #21 (1)
Item #20 (5)*
Item #23 (1)
Item #26 (4)
HARDWARE IDENTIFIER (CONTINUED)
06/03
P/N 211972B
3
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE IDENTIFIER (continued)
Item #35 (2)
Item #36 (1)
Item #37 (3)
Item #31 (1)
Item #39 (1)
Item #42 (4)
Item #50 (1)
Item #43 (2)
Item #51 (2)
Item #46 (2)
Item #55 (12)*
Item #53 (2)
Item #58 (7)
Item #60 (4)
Item #59 (4)
Item #65 (1)
Item #67 (8)
*You may have extra parts with this model.
P/N 211972B
06/03
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU START!
To ensure optimal playability of backboard system, a close tolerance fit between the elevator components and
hardware is required. Test fit large bolts into large holes of elevator tubes, backboard brackets and triangle plates.
Carefully rock them in a circular motion to ream out any excess paint from holes if necessary.
INSTRUCTIONS
IMPORTANT! WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF THIS
OWNERS MANUAL
21. Install pole mount assembly and reinforcement bracket (47) with carriage
bolts (46) to pole as shown. Tighten flange nuts (15) completely.
22. Push back sliding pin (43) as shown in Figure A to fit adjustable system
assembly through pole mount assembly. Then attach spring covers (48 &
49) onto pole mount bracket (45) with bolt (50), and nut (15) as shown in
Figure B.
1. Mark pole sections with tape as shown.
2. IMPORTANT! Bounce pole top (1) and middle section (2) together as
shown until they no longer move toward taped reference mark.
Upright assembly. NOTE: Pole sections should have a 3-1/2" (9 cm)
minimum overlap.
23. Attach backboard support brackets (52) to the backboard frame using bolts
(53), spacers (51), and nuts (37) as shown.
24. Attach lower elevator tubes (56) and spring (68) to backboard support
brackets (52) using spacers (59), bolt (57), and nut (58) as shown. NOTE:
Rim mounting nuts and bolts (60) supplied with rim hardware.
25. Attach upper elevator tubes (63) to backboard support brackets (52) using
spacers (59), bolt (57), and nut (58) as shown.
3. IMPORTANT! Holes in top (1) and bottom pole (3) sections MUST
align to correctly position elevator system toward playing surface.
Add bottom pole section (3) to assembly as shown and bounce until
completely tight. NOTE: Pole sections should have a 3-1/2" (9 cm)
minimum overlap.
26. Support pole on sawhorse. Attach backboard assembly to top pole section
(1) as shown. Then install pole cap (64). NOTE: Two people are
recommended for this step. Use caution; elevator assembly is heavy.
27. Install upper elevator tubes (63) to triangle plates (66) as shown.
Install handle assembly to lower elevator tubes (56) using bolt (57),
spacers (67), and nut (58) as shown. NOTE: Tighten bolt (57) in lock nut
(58) until flush (even) with lock nut’s outer edge. NOTE: Before going on
to next step, set adjustable system assembly to the 10’ (3.05 m) setting.
4. Install wheels (17) onto axle (28) and wheel bracket (25) with push caps
(29) as shown.
5. Position base as shown. Secure wheel bracket assembly with bolt (16) and
nut (15) as shown.
6. Install rod (4) through holes in bottom pole section (3) and eyebolt (5).
Insert pole assembly into tank (6) and through center hole on wheel
assembly as shown. Secure pole assembly with strap (61), washer (11)
and lock nut (8).
28.
WARNING: USE EYE PROTECTION WHEN INSTALLING SPRINGS.
Insert bolt (57) through left side upper elevator tube (63), then stretch
springs (68) onto bolt (57). Insert bolt (57) through right side upper
elevator tube (63) and secure with nut (58).
7. Secure base struts (9) to pole using bolt (10) washers (11) and nut (12) as
shown. Rotate the non-secured ends of base struts (9) as shown.
8. Secure base struts (9) to base using bolt (14) washers (11) and nut (15).
9. Install upper pivot bracket (18) to front of base using bolt (19), washer (20)
and nut (8) as shown.
29. Attach front cover (54) to hinge tubes (24) using carriage bolt (42) and
flange
10. Insert bolt (21) through lower pivot bracket (22) as shown, bolt (21) will be
secured during step 12. Carefully place base assembly on its side. Install
lower pivot bracket (22) with bolt (23), washers (20) and lock nut (8) as
shown.
nuts (15) as shown.
30.
WARNING: DO NOT LEAVE ASSEMBLY UNATTENDED WHEN
EMPTY, MAY TIP OVER.
Apply height and moving label (76) to front of pole as shown.
11. Secure both hinge tubes (24) to second wheel bracket (25) with carriage
bolts (26) and flange nuts (15).
31. Roll completed assembly to desired playing area. Secure assembly to
ground using strap (61) and tie down stake (7). Fill tank with 34 gallons of
water. IMPORTANT! Add two gallons (7.6 Liters) of non-toxic
antifreeze in sub-freezing climates. Add two gallons (7.6 liters) to tank
to prevent freezing in sub-freezing climates. Snap cap (62) into place.
12. Install wheels (27) onto axle (28) and wheel bracket (25) with push caps
(29) as shown.
13. Position base as shown. Secure wheel bracket assembly with disc (30),
washer (20) and nut (8) as shown. NOTE: Two people recommended for
this step.
WARNING: DO NOT ALLOW CHILDREN TO ADJUST HEIGHT.
32. Grasp handle and depress lever.
33. Push toward pole while holding lever. Raise or lower lever to desired
height while pushing forward on handle.
14. Carefully reposition entire assembly as shown. IMPORTANT! Two people
recommended for this step.
15. Snap tinnerman nut (31) onto inner channel (32). Place inner channel into
outer channel (33) as shown.
34. Release handle making sure that horizontal pin (43) is locked into slot.
16. Slide handle (34) into position as shown and secure with bolts (35),
washers (11), and nuts (15). Tighten completely.
WARNING: USE OF THIS PRODUCT WITHOUT PROPER
INSTALLATION OF SMART CLIPS, OR WHEN ALL SMART CLIPS ARE
NOT PRESENT COULD RESULT IN BODILY HARM. BE SURE TO
FOLLOW DIRECTIONS CAREFULLY.
17. Install bolt (36), washers (11), and nut (37) as shown. Tighten until
washers (11) are no longer loose. NOTE: Do not over tighten. Assemble
trigger (38) to handle assembly (34, 32, 31) as shown and secure with bolt
(39) and washer (11). Tighten completely.
35. Install net clips as shown. (See illustration)
36. Install net as shown. (See illustration)
18.
WARNING: USE EYE PROTECTION WHEN INSTALLING SPRINGS.
Install trigger return spring (40) to handle assembly (32, 33) as shown.
19. Attach Accuheight label (41) to inner channel (32).
20. Attach spring (44) to pins (43) and install pins (43) onto pole mount bracket
(45). Attach other spring (44) to opposite side. NOTE: Gently enlarge
eyelets of spring with pliers if springs do not fit over pins.
WARNING: USE EYE PROTECTION WHEN INSTALLING SPRINGS.
06/03
P/N 211972B
5
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT! WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF THIS OWNERS MANUAL
2
1.
MIDDLE
5"
(13 cm)
3
1
TOP
BOTTOM
5"
(13 cm)
IMPORTANT!
(See Text Page)
IMPORTANT!
(See Text Page)
3.
2.
Note
(See Text Page)
Note
(See Text Page)
2
1
2
3
1
Wood Scrap
P/N 211972B
06/03
6
Download from Www.Somanuals.com. All Manuals Search And Download.
16
4.
5.
17
29
25
28
17
16
29
15
6.
4
4
6
5
1
2
3
5
Note
(See Text Page)
61
11
8
61
11
8
7.
3
9
9
12
11
11
10
13
9
06/03
P/N 211972B
7
Download from Www.Somanuals.com. All Manuals Search And Download.
14
9.
8.
9
8
11
20
18
11
19
15
11.
10.
26
24
21
8
18
20
25
20
22
23
15
27
13.
12.
25
29
Note
(See Text Page)
27
28
21
IMPORTANT!:
30
20
SIDE OF WHEEL
WITH LONGER
PLASTIC AXLE
NEEDS TO FACE THE
WHEEL BRACKET.
8
29
P/N 211972B
06/03
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ELEVATOR INSTALLATION (See steps 14-21)
14.
15.
32
IMPORTANT!
(See Text Page)
33
32
31
17.
16.
11
11
37
36
Note
(See Text Page)
34
38
32
34
35
35
31
34
11
39
11
39
11
15
11
15
18.
19.
41
40
WARNING
(See Text Page)
33
32
33
32
06/03
P/N 211972B
9
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
21.
20.
47
(See Text Page)
46
1
43
45
15
44
44
Note
(See Text Page)
FRONT
SIDE
45
43
15
22.
Fig. A
Fig. B
45
15
49
48
43
50
P/N 211972B
06/03
10
Download from Www.Somanuals.com. All Manuals Search And Download.
23.
52
37
51
52
52
51
53
53
24.
Note
(See Text Page)
58
15
68
52
56
68
59
59
57
69
Refer To
Instructions
56
Included With Rim
Hardware For Rim
Assembly.
60
06/03
P/N 211972B
11
Download from Www.Somanuals.com. All Manuals Search And Download.
25.
58
59
52
63
59
57
56
56
63
26.
58
56
67
66
1
Note
(See Text Page)
64
66
67
56
57
65
P/N 211972B
06/03
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
(See Text Page)
27.
58
63
58
67
56
67
67
66
67
57
56
57
63
28.
63
58
57
WARNING
(See Text Page)
63
68
06/03
P/N 211972B
13
Download from Www.Somanuals.com. All Manuals Search And Download.
29.
WARNING
(See Text Page)
15
24
54
42
ELEVATOR HEIGHT ADJUSTMENT
NOTE:
30.
Peel protective film from
surface of acrylic
33.
32.
34.
backboard prior to use.
10 feet
71
WARNING
(3.05m)
(See Text Page)
43
IMPORTANT!
(See Text Page)
31.
62
7
61
P/N 211972B
06/03
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Install net clips.
WARNING: Use of this product without proper installation of net
clips, or when all net clips are not present could result in bodily harm. Be sure
to follow directions carefully.
35.
CLIP “ARM”
CLIP “BODY”
69
Insert one “arm” of clip into ram as shown. Twist “body” of clip slightly so that
second “arm” slides over the top of the first “arm” as shown.
Push in direction indicated by arrows.
55
A
Push second “arm” back and into ram as shown.
B
Twist “body” of clip slightly again to spread “arms” of clip.
Clip “arms” must be flat and touching edge to edge as shown, not overlapping.
C
06/03
P/N 211972B
15
Download from Www.Somanuals.com. All Manuals Search And Download.
NET INSTALLATION
69
36.
SIDE VIEW
55
NETCLIP
70
NET
Insert net into bottom of clip as shown.
SIDE VIEW
Twist net until it snaps into position.
Net must be centered through clip.
NETCLIP
NET
P/N 211972B
06/03
16
Download from Www.Somanuals.com. All Manuals Search And Download.
|