Operator’s manual
Please read the operator’s manual carefully and make sure you
understand the instructions before using the machine.
GB
Husqvarna
PG680
Manual de
ES instrucciones
Lea detenidamente el manual de instrucciones y asegúrese de
entender su contenido antes de utilizar la máquina.
Bedienungsanweisung
DE
PG820
Lesen Sie die Bedienungsanweisung sorgfältig durch und machen
Sie sich mit dem Inhalt vertraut, bevor Sie das Gerät benutzen.
GB ES DE FR
Manuel d’utilisation
FR
Lire attentivement et bien assimiler le manuel d’utilisation avant
d’utiliser la machine.
HUSQVARNA CONSTRUCTION PRODUCTS
Download from Www.Somanuals.com. All Manuals Search And Download.
Key to symbols
Key to symbols
The symbols below are used on the machine and in
this Operator’s Manual. It is important that the user
understands the significance of these in order to work
with the machine safely.
Please read the operator’s manual
carefully and make sure you under-
stand the instructions before using the
machine.
Inspection and/or maintenance should
be carried out with the motor switched
off and the plug disconnected.
Visual check.
WARNING! Dust forms when grinding
which can cause injuries if inhaled. Use
an approved breathing mask. Always
provide for good ventilation.
Regular cleaning is required.
Always wear:
•
•
•
•
Approved protective helmet
Approved hearing protection
Protective goggles or a visor.
This product is in accordance with ap-
plicable EC directives.
Dust forms when grinding, which can
cause injuries if inhaled. Use dust
mask.
Always wear sturdy non-slip boots with
steel toe-caps.
Always wear approved protective
gloves.
English - 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
•
Never use the machine if you are tired, if you have
Safety Instructions
drunk alcohol, or if you are taking medication that
could affect your vision, your judgement or your co-
ordination.
WARNING
Under no circumstances may the machine be
•
•
Never use a machine that has been modified in any
way from its original specification.
started without observing the safety instruc-
tions. Should the user fail to comply with
these, Husqvarna Construction Products
Sweden AB or its representatives are free
from all liability both directly and indirectly.
Read through these operating instructions
and make sure that you understand the
contents before starting to use the machine.
Should you, after reading these safety in-
structions, still feel uncertain about the safety
risks involved you must not use the machine,
please contact your dealer for more informa-
tion.
Be on your guard for electrical shocks. Avoid having
body contact with lightning-conductors/metal in the
ground.
•
Never drag the machine by means of the cord and
never pull out the plug by pulling the cord. Keep all
cords and extension cords away from water, oil and
sharp edges.
•
•
Make sure the cord is not pinched in doors, fences
or the like.
Check that the cord and extension cord are intact
and in good condition. Never use the machine if the
cord is damaged, hand it in to an authorized service
workshop for repair.
•
•
Please read the operator’s manual carefully.
Only qualified staff should be allowed to operate
machinery.
•
•
Do not use a rolled up extension cord
•
Never use a machine that is faulty. Carry out the
checks, maintenance and service instructions de-
scribed in this manual. All repairs not covered in this
manual must be performed by a repairer nominated
by either the manufacturer or distributor.
The machine should be connected to an earthed
outlet socket.
•
•
Check that the mains voltage corresponds with that
stated on the rating plate on the machine.
•
Always wear personal safety equipment such as
sturdy non-slip boots, ear protection, dust mask and
approved eye protection.
Ensure the cord is behind you when you start to use
the machine so that the cord will not be damaged.
At no time should lifting of machinery be attempted
without mechanical means such as a hoist or fork
lift.
•
•
The machine should not be used in areas where
potential for fire or explosions exist.
Machinery should only be started when grinding
heads are resting on the ground unless carrying out
a testing procedure as outlined in this manual.
WARNING!
Overexposure to vibration can lead to circula-
tory damage or nerve damage in people
who have impaired circulation. Contact your
doctor if you experience symptoms of overex-
posure to vibration. These symptoms include
numbness, loss of feeling, tingling, pricking,
pain, loss of strength, changes in skin colour
or condition. These symptoms normally ap-
pear in the fingers, hands or wrists.
•
The machine should not be started without the
rubber dust skirt attached. It is essential a good
seal between machine and floor be established for
safety, especially when operating in dry grinding
applications.
•
•
When changing the grinding discs ensure power
supply to the unit is OFF by engaging the Emergen-
cy Stop button and the power-plug disconnected.
The machine should not be lifted by handles, mo-
tor, chassis or other parts. Transportation of the
machine is best done on a pallet / skid to which the
machine must be firmly secured.
•
Extreme caution must be used when moving
machinery by hand on an inclined plane. Even the
slightest slope can cause forces/momentum making
the machinery impossible to brake manually.
6 - English
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Introduction
IMPORTANT!
The Husqvarna PG 680/820 floor surfacing machines
are designed for wet or dry grinding of marble, terraz-
zo, granite and concrete. Their applications range from
rough grinding through to a polished finish.
The machine should not be lifted by handle,
motor, chassis or other parts. Transportation
of the machine is best done on a pallet/skid
to which the machine must be firmly secured.
Do not attempt to slide the tines/forks from
a fork lift under grinding heads unless on a
pallet/skid. Failure to do so can cause irrepa-
rable damage to grinding heads of machine
and internal parts.
This manual covers the Husqvarna PG 680/820 series
of floor grinders equipped with twin motor drive here
after referred to as Dual Drive Technology™.
It is extremely important all users be familiar with the
contents of this manual before
It is recommended that machinery be transported with
a set of diamonds attached at all times to ensure pro-
tection of locking mechanism for diamond plates.
commencing operation of either machine. Failure to
do so may result in damage to machinery or expose
operator to unnecessary dangers.
IMPORTANT!
Storage
Only staff that have received the necessary
education, both practically and theoretically
concerning their usage should operate the
machinery.
The machine should always be stored in a dry place
when not in use.
Transportation
The machine comes equipped with inbuilt advanced
electronic systems called variable speed drives or
frequency converters. These drives enable the variable
speed and direction component of each of the motors.
The drives are located in the steel cabinet mounted on
the machine chassis.
As with all electronic equipment, the drives are sensi-
tive to excessive vibration, rough treatment and high
levels of dust. Much care and attention has been given
by the manufacturer to ensure maximal protection is
given to the drives. Note the shock absorbing mount-
ing system used to mount the steel cabinet on the
machine chassis/frame.
When transporting, it is important to ensure the ma-
chinery is properly secured at all times to eliminate
“bouncing” of the variable speed drives. Ensure the
chassis or frame section of the machine is secured
down at all times when in transit.
The machine should always be transported under
cover limiting the exposed to natural elements – in
particular rain and snow.
English - 7
Download from Www.Somanuals.com. All Manuals Search And Download.
What is what
1.
11.
2.
3.
4.
5.
10.
9.
6.
7.
8.
What is what
1. Hour counter
8. Chassis/Frame
2. Electrical cabinet
9. Handle bars
3. Planetary head motor 1.5kW/1Hp
4. Grinding/Satellite heads motor 11kW/15Hp
5. Lifting lugs
10. Control Panel
11. Handle bar adjuster
6. Cover/Shroud
7. Skirt
8 - English
Download from Www.Somanuals.com. All Manuals Search And Download.
What is what
The machine can be divided into two main parts. These
can be identified as follows:
IMPORTANT!
Planetary head and grinding heads are set
to both turn in the same direction (i.e. both in
clockwise rotation or both in counter-clock-
wise rotation).
1. Chassis/Frame section – comprising handle bars,
electrical cabinet, steel frame and wheels.
Clockwise rotation of speed control will in-
crease speed of planetary head and grinding
heads.
2. Head – comprising of motors, cover, grinding/satel-
lite/
planetary heads and internal components.
The machine has been manufactured to allow move-
ment between the chassis and head via the connection
point at the lifting lugs and chassis pins. This move-
ment is important during the grinding process as it
creates a “floating” effect for the head.
Grinding satellite/ heads
Planetary head
The floating gives the head a self-leveling effect, negat-
ing the need to adjust the height of the head as the
machine passes over floor areas with different slopes
or undulations.
Control panel
The control panel consists of a number of switches and
dials giving 8 separate controls (see picture).
Power - This button, when depressed, will turn on
power supply to the unit when the EMERGENCY
STOP button has been released.
Dust extraction port
Emergency Stop - When pushed will immediately
shut down machine by totally stopping power supply to
drives/ frequency converters in electrical cabinet.
Head Speed - Direction control for planetary head rota-
tion.
Fwd/Rev (Yellow) - Direction control for planetary head
rotation.
Disc Speed - Speed control for grinding heads.
Fwd/Rev (Red) - Direction control for grinding heads.
Reset - Will clear fault function/error message on
drive/frequency converter (located in electrical cabinet)
in case of fault occurring.
Stop/Run - To start or stop machine during normal
operation.
IMPORTANT!
It is important to use the STOP/RUN switch
to control the running of the machine, not
the EMERGENCY STOP button. Each time
the EMERGENCY STOP button is pressed
it shuts down the drive/frequency converter.
Frequently powering up and down of the
drive/frequency converter will reduce the life
span of the drive/ frequency converter.
Control panel
English - 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up/Operation
Setting up/Operation
Position grinder on the working area. Make sure there
are diamonds underneath machine and that the head
locks/shear pins are tight.
IMPORTANT!
When using the machine, each grinding head
must always have the same diamond type
and number of diamonds as the other grind-
ing heads. Each grinding head must have
diamonds the same height as the other grind-
ing heads.
Powering up machine
Adjust rubber skirt so that a good seal is established
between the floor and head of machine (see picture
below). Ensure join in skirt is at the front of the ma-
chine. Setting of the skirt is essential to obtain good
dust extraction and eliminate the possibility of airborne
dust when dry grinding.
i. Ensure the STOP/RUN switch is set on Stop
(rotate counter clockwise).
ii. Plug power supply to machine. Only turn power on
at
switch once fully connected.
iii. Disengage Emergency Stop button (twist clock-
wise).
iv. Depress Power button. On doing so, a soft “clunk”
should be heard to come from within the electrical cab-
inet. This indicates the line contactors have engaged,
supplying power to the drives/frequency converters.
Setting Speed and direction
On the control panel there is a FORWARD/REVERSE
and Speed dial knob. Generally, when starting the
machine for the first time on any given application, it is
advised the speed setting should not exceed 7, initially.
Set handle to most comfortable working height using
adjustment lever.
IMPORTANT!
When the operator is comfortable with the application,
speed may be increased.
It is recommended that this height be set as
close as possible to the height of the opera-
tor’s hip bone. When the machine is running,
there will be a grinding force/pull to one side
that can be felt through the handlebars. Use
the hip to resist this force instead of trying to
control this through the arms (such position-
ing will be much easier for the operator using
the machine over prolonged periods of tim.
10 - English
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up/Operation
Speed and direction setting is often a matter of per-
sonal choice. Operators are encouraged to experiment
to find which settings best suit the given applications.
The following table lists some suggested set-ups for
different applications.
Application
Planetary
head
Planetary
head
Grinding disc Grinding disc
direction
speed
direction
speed
Ceramic tile adhesive removal
Carpet glue removal
FWD
FWD
FWD
FWD
FWD
FWD
FWD
REV
FWD
FWD
FWD
6-7
5-7
5-10
7-10
7-8
5-7
10
FWD
FWD
FWD
FWD
FWD
FWD
FWD
REV
FWD
FWD
FWD
8-10
8-10
8-10
8-10
8-10
8-10
8-10
3-5
Epoxy paint removal
Rain damaged concrete
Smoothen exposed aggregate
Lippage removal in terrazzo/stone tiles
Concrete polishing with resin bond pads
PIRANHA™ scraper tool
3-5
5-7
5
FLEXOR™ flexible heads
Bushhammer/Scarrifier tools
5-7
5-7
Re-grouting procedure during HiPERFLOOR™
process
8-10
3-5
IMPORTANT!
Direction is also a matter of personal preference. It
should be noted, however, that when both grinding
discs and planetary heads are running in the same
direction, a more powerful grinding force is created be-
tween the diamond abrasives and floor being ground.
The end result is higher productivity than when the
discs are set to run in opposite directions. It is here
that you will also experience the beneift of Dual Drive
Technology™.
In the above table, FWD & FWD are listed
together to indicate direction settings in the
same direction (i.e. It can also be REV/REV).
The only application where direction set-
tings must be in the same directions and also
direction specific is when using the PIRA-
NHA™ scraper tools. In this particular ap-
plication the setting must be in the REV/REV
direction.
Production tip - To improve the cutting efficiency of
diamonds, change directions on a regular basis. This
will work both sides of the diamond crystals, keeping
the abrasives as sharp as possible by creating maxi-
mal exposure of the diamond crystal.
Direction of rotation
The correlation between FWD/REV & Clockwise/Coun-
ter clockwise rotation can be said as follows if looking
at the grinding discs from underneath the machine:
Once both a speed and direction have been
nominated, switch on dust extraction or vacuum de-
vice.
1. REV—Clockwise.
2. FWD—Reverse.
IMPORTANT!
As mentioned, when the machine is in operation it will
“pull” to one side. The direction of pull is determined by
the planetary head direction of rotation. The head of
the machine will pull to the right (and therefore, will be
felt on the right hip of the operator) when the planetary
head is set in the REVERSE direction.
It is highly recommended to use the Husq-
varna
DC 5500 dust extraction system
for complete dust control.
Standing behind machine with handlebars set as
described earlier, apply a small amount of downward
pressure on the handle. Switch the machine to run
mode using the STOP/RUN switch on the control
panel. The machine should start smoothly and acceler-
ate to the selected speed over a period of 5 seconds
This sideways pull can be very useful when grinding,
particularly along a wall. Set the machine so that it
pulls towards the wall, and then control the machine so
it can just touch the wall. This will ensure a grind close
to the wall or object.
English - 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the diamonds
Changing the diamonds
As different applications require different selections of
diamond tools, there will be many occasions when the
grinding discs need to be changed.
Following is a guide for this procedure.
Preparation
1. Ensure STOP/RUN switch is in STOP position as
unintentional starting of machine while changing
discs
can result in serious injury.
2. Have a set of gloves ready, as diamonds can get
very
hot during dry grinding applications.
Changing
1. Set handle in upright position (illustrated right).
2. Pull back on handle to lift grinding head off the
ground.
4. Lay machine back on the ground.
5. Put on gloves.
6. Remove grinding disc by slightly rotating disc and
then
pull off (direction that the discs will need to be ro-
tated
will depend on the direction the machine was last
running).
7. Check to ensure all head locks/shear pins are tight.
8. Once new diamonds have been attached, reverse
procedure to lower machine to ground.
9. As new diamonds may be a different height to set
being previously used, re-adjust skirt to ensure
good seal is established with the floor.
12 - English
Download from Www.Somanuals.com. All Manuals Search And Download.
Variable speed drives/frequency converters
Variable speed drives/
frequency converters
Each Husqvarna PG 680 & 820 is equipped with 2
variable speed drive or frequency converter. This
unit is incorporated into the machine for the following
reasons:
1. Functional
•
Manipulate incoming power to enable increase/
decrease in speed & direction change.
•
Regulate current and voltage supply to the motors
to ensure motors run at optimum levels (e.g.
torque boost).
1.
8.
2. Protection/Diagnostic
Protection
•
Monitors incoming power to ensure suitability for
machine and application being performed.
2.
•
Controls current being drawn by motors to ensure
motors are running within safe operational limits (to
prevent damage to motor).
7.
•
•
Monitors load on machine to ensure the grinder is
not being overloaded thus offering protection for
belt, bearings and other internal components.
Protects motors from faulty power supply (e.g. run-
ning on 2 phases).
Diagnostic
•
•
•
Identifies electrical faults with the machine and
registers fault code.
4.
3.
5.
6.
Keypad display
Has monitoring menus that help isolate cause of
potential electrical faults.
Monitoring menus also enable operator to gauge
how hard machine is working. Whilst it is not essen-
tial for an operator to intimately know every feature
of the variable speed drives or frequency convert-
ers, it is useful to be familiar with both the fault
codes as well as some of the monitoring menus.
1. Run direction (fwd or rev)
2. Indicates if unit is either stopped or running
3. Up key
4. Left key
5. Down key
6. Reset button
Keypad/Display
7. Output mode (Hertz in this example)
8. Output value
Each variable speed drive or frequency converter has
a keypad which will appear as illustrated on the right
when the machine has power connected to it.
English - 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Variable speed drives/frequency converters
Monitor screen
Information provided
OUTPUT FREQUENCY
REF. FREQUENCY
MOTOR SPEED
Frequency motor is running at when machine is running.
Frequency speed control dial is set to.
Speed of motor when machine is running.
Current draw of motor when machine is running.
Percentage of motor torque when machine is running.
Percentage of motor power when machine is running.
Percentage of motor voltage when machine is running.
Indicates quality of power supply.
MOTOR CURRENT
MOTOR TORQUE
MOTOR POWER
MOTOR VOLTAGE
DC LINK VOLTAGE
The menu tree illustrated on this page outlines the
important menu options that provide useful information
for monitoring and diagnostic purposes when using the
machine.
Parameter Menu
DC Link Voltage
Keypad
Control Menu
As can be seen on the menu tree to the right, when
the machine is turned on, the variable speed drives or
frequency converters are set to display the Output Fre-
quency to the motor (a zero value will register when the
machine is in stand-by mode).
Motor Voltage
Motor Power
Active Faults Menu
Faults History Menu
System Menu
The Output Frequency page also falls under the Monitor
Menu.
It can be seen from the left hand column, the two primary
menus important to the operator are the Monitor Menu
and Fault History menu.
Motor Torque
Motor Current
Motor Speed
Navigation through the menu tree is achieved by us-
ing the up, down, left and right keys on the keypad (see
previous page).
Expanded Boards
Menu
Monitor Menu
Output Frequency
14 - English
Download from Www.Somanuals.com. All Manuals Search And Download.
Variable speed drives/frequency converters
Menus and information they provide
FAULT HISTORY
The following menu items/screens on the variable
speed drive/frequency converters provide the following
useful information to the operator.
The fault history menu stores the last series of faults
experienced by the variable speed drive/frequency
converter. If there is a recurring fault pattern experi-
enced by the machine, the information can be obtained
from the fault history menu. For more on faults, see
trouble shooting faults
OUTPUT FREQUENCY (Monitor Menu)
This screen tells the operator the frequency the motor
is running at when the machine is in operation. The
value for output frequency should be constant when
the machine is running. If there is a fluctuation in
output frequency when the machine is running, gener-
ally this indicates the motor is running at or near the
limit of its programmed current limit. The current limits
(predetermined and set by Husqvarna Constructions
Products) are as follows:
1. Large motor (which information is found on the large
variable speed drive/frequency converter) - 25
amps.
2. Small motor (which information is found on the small
variable speed drive/frequency converter) - 5 amps.
If there is a fluctuation in output frequency when the
machine is in operation, it is advisable to check the
motor current as well. This can be found by pressing
the UP arrow on the keypad 3 times. For trouble free
operation concerning current issues, it is best to keep
output current at or around 21 amps (for the large mo-
tor). The current draw of the motor can be reduced by
reducing the speed of the motor using the speed dial
on the control panel near the handle bars.
Generally speaking, most over-current problems will
be associated with the large motor (and therefore,
monitored on the large variable speed drive/frequency
converter). Keep the current draw on the small motor
under 3.5amps for consistent operation.
MOTOR CURRENT (Monitor Menu)
This screen displays the current draw of the corre-
sponding motor (i.e. large variable speed drive/fre-
quency converter monitors function of large motor,
small variable speed drive/frequency converter moni-
tors function of small motor) when the motor is running.
See comments already covered under OUTPUT FRE-
QUENCY relating to motor current.
DC LINK VOLTAGE (Monitor Menu)
This screen displays the quality of the power supply to
the machine. It will read higher values when the ma-
chine in standby and lower values when the machine
is in operation.
English - 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Faults and trouble shooting
Faults and trouble shooting
When either one of the variable speed drives or frequen-
cy converters in the machine experience a fault and “trip”
out, they will cease to run and an error message will ap-
pear flashing on the keypad display (see picture below).
The following list are the most commonly experienced
faults and possible action steps.
Fault code
Fault Code
Possible Cause
Action
1—OVERCURRENT
Motor being worked too hard and
drawing extra current.
Check current being drawn when machine is
running. Reduce speed setting and current draw
back into acceptable limits as described on
previous page.
Short circuit on output side of vari-
able speed drives or frequency con-
verters.
Check wiring in plugs connected to motor cables
or inside connection boxes on motors.
Motor failure (very rare)
Have motor tested and replace if required.
3—EARTH FAULT
Short circuit on output side of vari-
able speed drives or frequency con-
verters.
Check wiring in plugs connected to motor cables
or inside connection boxes on motors.
Motor failure (very rare)
Have motor tested and replace if required.
9—UNDERVOLTAGE
Insufficient voltage supply to ma-
Check power supply and ensure correct voltage.
chine.
Power supply to variable speed
drives or frequency converters has
been turned off.
Re-connect power to grinder.
11—OUTPUT PHASE
SUPERVISION
Short circuit on output side of vari-
able speed drives or frequency con-
verters.
Check wiring in plugs connected to motor cables
or inside connection boxes on motors.
Motor failure (very rare)
Have motor tested and replace if required.
14—UNIT OVER TEM-
PERATURE
Variable speed drives or frequency
converter over temperature due to
high temperature working environ-
ment or faulty temperature sensor.
Open door on electrical cabinet to increase ven-
tilation.Have variable speed drives or frequency
converter tested by service agent.
15—MOTOR STALLED
Motor being worked too hard and
drawing extra current.
Check current being drawn when machine is
running. Reduce speed setting and current draw
back into acceptable limits as described on
previous page.
Mechanical jam preventing motor
from turning.
Try rotating grinding discs and planetary head by
hand to see if jam exists
16 - MOTOR OVERTEM- Motor being worked too hard and
PERATURE drawing extra current.
Check current being drawn when machine is
running. Reduce speed setting and current draw
back into acceptable limits as described on
previous page.
16 - English
Download from Www.Somanuals.com. All Manuals Search And Download.
Faults and trouble shooting
Further problems that may be experienced when using the grinder and potential solutions are as follows:
Problem
Possible Cause
Potential Solution
GRINDER IS HARD TO HOLD
ONTO
Not enough diamonds under the
machine (if grinding thick glue or
soft floors, too few diamonds under
the machine will greatly increase
the load on grinder and operator).
Usually also accompanied by high
current draw by large motor.
Increase number of diamonds under machine to
reduce load on grinder and operator.
Large motor not working (this can
be caused by fault with motor, fault
with wiring to motor, or fault with
large variable speed drive or fre-
quency converter).
Check large motor is plugged in. Check there
are no faults on larger variable speed drive or
frequency converter. Check that large variable
speed drive or frequency converter is on. Check
that large variable speed drive or frequency
converter is func tioning properly (unplug both mo-
tors, set display on keypad to Output Frequency,
switch machine to RUN, see if numbers on screen
change from zero and begin counting up. If num-
bers stay on zero, large variable speed drive or
frequency converter is not receiving run command
from switch on control panel. Machine needs to
be checked by an electrician or by Husqvarna
Construction Products
Drive belt is slipping.
Remove belt tensioner cover plate on bottom of
machine and check there is no water or dust on
the inside of the machine that may be causing the
belt to slip on the drive pulleys.
Drive belt is broken (this can be
confirmed by turning one of the
grinding heads by hand. If all grind-
ing heads rotate together, belt is not
broken. If only one grinding head
turns, belt is broken).
Replace internal drive belt.
GRINDER SOUNDS LIKE IT IS
OVERREVVING
Small planetary drive motor not
plugged in.
Check small planetary drive motor is plugged in.
Small motor not working (this can
be caused by fault with motor, fault
with wiring to the motor, or fault
with large variable speed drive or
frequency converter).
Check small motor is plugged in. Check there are
no faults on small variable speed drive or fre-
quency converter. Check that small variable speed
drive and frequency converter is on. Check that
small variable speed drive or frequency converter
is functioning properly (unplug both motors, set
display on keypad to Output Frequency, switch
machine to RUN, see if numbers on screen
change from zero and begin counting up. If num-
bers stay on zero, small variable speed drive or
frequency converter is not receiving run command
from witch on control panel. Machine needs to be
checked by an electrician or Husqvarna Construc-
tion Products.
GRINDER IS JUMPING AROUND
Grinding heads may be worn-out or Check grinding heads for broken parts or excess
damaged.
movement.
Diamonds may not be fitted cor-
rectly or different height diamonds
may be on the grinding heads.
Check to ensure all diamonds are fitted correctly
and are the same height.
Head locks may be loose or miss-
ing.
Check to ensure all head locks are present and
tight.
English - 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Diamonds
Diamonds
NUMBER OF DIAMOND SEGMENTS/PADS UNDER
THE MACHINE
Increasing the number of segments under the machine
will:
Background
Diamond abrasives usually consist of 2 components:
•
•
•
Reduce pressure on each individual diamond seg-
ment.- Reduce wear rate on diamond segments.
1. Diamond powder (also known as diamond crystals
or grit). By changing the size of the diamond powder
or grit, we can change how coarse or fine the
scratches will be that are left behind from the
grinding process.
Reduce load on the machine and cause the grinder
to draw less current.
Create a smoother scratch pattern (particularly on
soft floors).
2. A binding agent (metal or resin). Diamond powder
is mixed and suspended in either a metal or resin
binding agent. When suspended in a metal binding
agent, the finished product is referred to as a Metal
Bond or Sintered diamond segment. When suspend-
ed
in a resin binding agent, the finished product is
referred to as a Resin Bond diamond segment or
pad. By changing the hardness of the binding agent,
we can change how fast or slow the diamond abra-
sive
The opposite will occur when decreasing the number
of segments under the machine.
WET AND DRY GRINDING
When using diamond segments wet, the following
principles apply:
•
•
Production rates will be higher than dry grinding.
will wear.
Diamond segments will wear faster (due to pres-
ence of slurry) and therefore, harder bonds can be
used (when comparing with dry grinding).
General Principles
The following are general rules regarding diamond seg-
ments in grinding applications. As with all general rules
there are exceptions or cases when it is not the case.
•
Scratches from diamond grit will be deeper.
When using diamond segments dry, the following prin-
ciples apply:
DIAMOND GRIT SIZE
Changing the size of the diamond grit to a smaller par-
ticle/grit size will effect the performance of the diamond
tool in the following ways:
•
Production rates will be slower on harder materials
than if wet grinding.
•
Softer bond segments will be required in order to
encourage segment wear (as there will be not slurry
to help diamond segments to wear).
•
•
Create a finer scratch pattern.
Increase the life of the diamond tool.
•
•
Scratches from diamond grit will not be as deep
compared to if it were also used for wet grinding.
The opposite will occur when changing to a larger
particle/grit size.
There will be more heat generated by the diamond
segment.
BINDING AGENT—METAL BOND OR RESIN BOND
Increasing hardness of bond will:
Summary of diamond principles
•
•
•
Increase life of diamond tool.
Decrease production rate.
Diamond segments need to wear in order to achieve
productivity. Diamond segment wear can be influenced
by the following factors:
Cause diamond tool to leave finer scratches in dry
- grinding applications (when compared to a softer
bond diamond tool with the same diamond grit size).
•
•
•
•
•
•
Pressure.
Hardness of bond.
The opposite will occur when making the metal or resin
bond softer.
Diamond grit size.
Presence of water.
Number of segments under the machine.
Adding an additional abrasive (e.g. sand, silicone
carbide) on the floor will increase wear.
18 - English
Download from Www.Somanuals.com. All Manuals Search And Download.
Diamond selection
Diamond Holder Disc
Full set of single segments
Half set of single segments
Position for Diamond segment
Full set of twin segments
Half set of twin segments
Diamond selection
The following section covers important factors to
consider when selecting the diamond segment you are
going to use for a given application.
Generally speaking, the faster a diamond segment
wears, the faster the productivity will be. By varying the
above factors, changes can also be made to effect the
following:
Grinding disc set-up
•
•
•
•
Scratch pattern.
The way diamond segments are set-up on the grinding
heads of the machine will also greatly influence the
performance of the machine, the productivity levels
and also the finished floor quality.
Current draw of machine.
Flatness of floor (see next section).
Ease of operation.
There are basically two types of diamond configura-
tions that can be used when using the grinder:
1. Full set of diamonds – when there are diamonds
placed
at each of the six positions on the diamond holder
discs
(see pictures above).
2. Half set of diamonds – when there are diamonds
placed
at three alternating positions on the diamond holder
discs (see pictures above).
English - 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Diamond selection
Full and half sets of diamonds
By changing the way the diamonds are set-up on the
diamond holder discs, an operator can significantly ef-
fect the performance of the machine and therefore, the
finished product.
HALF-SET OF DIAMONDS
When the diamonds are set-up as a half-set, they tend
to follow the surface of the floor. Similar to a tripod for a
camera, which can be placed on an uneven surface and
yet still find a stable footing.
The half-set diamond configuration should only be used
when a flat floor finish is not required.
FULL-SET OF DIAMONDS
When the diamonds are set-up as a full-set, they tend
not to follow the surface of the floor. If the floor has undu-
lations, the machine will grind the high areas yet miss
the low spots (unless the high areas are ground down
first).
The full-set diamond configuration should be used when
a flat floor finish is desired.
The below table gives some examples of possible ap-
plications for the two arrangements:
Application
Full set is best Half set is best
Ceramic tile adhesive removal
Carpet glue removal
X
X
X
X
X
X
X
X
X
X
X
X
Epoxy paint removal
Vinyl adhesive removal
Rain damaged concrete
Smoothen exposed aggregate
Lippage removal in terrazzo/stone tiles
Surface polishing of concrete floors
Grinding to expose aggregate in concrete polishing application
Remove lippage from terrazzo/natural stone tiles
Flatten undulations in concrete floors
Re-polish floors that have been ground before
20 - English
Download from Www.Somanuals.com. All Manuals Search And Download.
Diamond selection
Selecting the correct diamonds for your application
The following suggestions cover the basic principles for
diamond selection for different applications.
Application
Metal
bond
Grit size
Full-
set
Half
set
Singles /
Twins
Flatten floor - Hard concrete
SOFT
16 or 30
X
S
Flatten floor - Medium concrete
MEDIUM 16 or 30
X
X
X
S
Flatten floor - Soft concrete
HARD
HARD
SOFT
16 or 30
T
Ceramic tile adhesive removal
6, 16 or 30
16 or 30
S/T
S/T
T
Vinyl or Carpet glue removal - Hard concrete
Vinyl or Carpet glue removal - Medium concrete
Vinyl or Carpet glue removal - Soft concrete
Epoxy paint removal - Hard concrete
Epoxy paint removal - Medium concrete
Epoxy paint removal - Soft concrete
Rain damaged concrete
X
X
X
X
MEDIUM 6 or 16
HARD
SOFT
6 or 16
T
6, 16 or 30
X
X
X
X
X
X
S
MEDIUM 6, 16 or 30
S
HARD
HARD
HARD
SOFT
SOFT
6, 16 or 30
16 or 30
16 or 30
30 or 60
60
S/T
S/T
S/T
S
Smoothen exposed aggregate
Lippage removal in terrazzo - stone tiles
Surface polishing of concrete floors - Hard concrete
Surface polishing of concrete floors - Medium concrete
Surface polishing of concrete floors - Soft concrete
X
X
X
S/T
S/T
T
MEDIUM 60
HARD
60
Grinding to exposed aggregate in concrete - Hard concrete SOFT
16 or 30
X
X
S
Grinding to exposed aggregate in concrete - Medium con-
crete
MEDIUM 16 or 30
S
Grinding to exposed aggregate in concrete - Soft concrete
Flatten undulation in concrete floors - Hard concrete
Flatten undulation in concrete floors - Medium concrete
Flatten undulation in concrete floors - Soft concrete
HARD
SOFT
16 or 30
16 or 30
X
X
X
X
T
S
S
T
MEDIUM 16 or 30
HARD 16 or 30
English - 21
Download from Www.Somanuals.com. All Manuals Search And Download.
Diamond selection
Determining the hardness of concrete
All concrete may feel hard (particularly if you fall over
on it), so what do we mean when we talk about hard,
medium and soft concrete?
All concretes are measured by their compressive
strength and depending on which part of the world you
are from, different compressive strength indices (e.g.
PSi & MPa). Generally speaking, the higher the com-
pressive strength rating, the harder the concrete and
therefore, the harder it will be to grind.
However, other factors beside compressive strength
ratings determine how hard the floor will be, and
therefore, the correct diamond selection. Since grind-
ing normally only deals with the surface of the concrete
(top 5mm or 1/4 inch), often the way the concrete floor
has been finished or the condition of the surface will
have a greater bearing on what type of diamond to
select, rather than the compressive strength rating of
the concrete.
SURFACE FACTORS TO CONSIDER WHEN MAK-
ING A DIAMOND SELECTION
Generally speaking, if a concrete surface is very
smooth (i.e. Most likely it has been heavily trowelled/
helicoptered), the concrete will behave as if it has a
high compressive strength and therefore, require a soft
bond segment.
Accordingly, if a concrete surface is coarse/aggressive
(e.g. rain-damaged, shot blasted, scarified, exposed
aggregate e.t.c.), the concrete will behave as if it has a
low compressive strength and therefore, require a hard
bond segment.
Surface coatings/contaminants (e.g. Epoxy coatings,
ceramic tile adhesives, levelling compounds/screeds)
will often have a larger bearing on what diamond to se-
lect, than will the compressive strength of the concrete.
As a general rule, when grinding a concrete slab for
the first time and you are unsure about its hardness,
always begin with harder bond diamonds under the
machine. This will ensure the least amount of wear on
the diamond segments. If a hard diamond segment
is not suited to the application, all it has cost is a little
amount of time without wearing out the diamonds.
If performed the other way around (i.e. a soft segment
is used to begin with) and the concrete is soft or pos-
sesses an abrasive surface or surface contaminant, it
is quite possible to wear-out a considerable amount of
diamond in very short period of time.
22 - English
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
The head pins are fixed to the head plate giving rigid-
Maintenance
Used correctly, the machine is an extremely low-main-
tenance and reliable.
ity and stability. The head mate is situated above the
head plate and is held in place by a series of holes
– head pin holes.
1.
1.
This section covers the general maintenance items
that need attention on a periodic basis.
There are three main mechanical items to check:
1. Grinding Heads.
2.
2.
2. Planetary drive system.
3. Planetary seal.
1. Head mate
2. Head pin hole
1. Head plate
2. Head pins
Grinding heads
There are 2 different grinding head options:
Between the head plate and head mate are 3 white
silicone springs which give shock absorption and flex-
ibility in the system.
11. Conventional / Demolition heads—designed for
heavy duty preparation grinding where an extremely
robust system is required.
The head pins are able to move within the head pin
holes, creating a shock absorber type system similar to
that in most motor vehicles.
2. Spring steel head system—designed more for finish-
ing or lighter grinding applications.
Over an extended period of time, the head pin holes
wear open. Along with this, the head pins wear and
reduce in diameter. This combined wearing of the two
creates excessive movement or “slop” within the grind-
ing heads. This “slop” will eventually cause vibration
whilst the machine is operating.
CONVENTIONAL/DEMOLITION HEADS
The below diagram illustrates the main parts compris-
ing this type of grinding head.
Routine checks for slop in the grinding heads are
recommended. Life expectancy for grinding heads can
vary between 6 and 12 months depending on amount
of usage.
Replacement heads are available and simply bolt into
place when the old ones are removed
1.
2.
4.
3.
1. Head mate
2. Head plate
3. Head lock
4. Head spring
The interrelation between the above four components
enables a dynamic system which is both robust and
flexible.
English - 23
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Spring Steel Heads
Between the head plate and head mate are a series of
white silicone springs, spacers and the spring steel spring
which give shock absorption and flexibility in the system.
The below diagrams illustrate the main parts comprising
this type of grinding head.
Unlike with the conventional/demolition heads, the spring
steel heads are able to move in a flexible manner without
any moving parts due to the presence of the spring steel
spring.
Diagram 1
1. Spring steel spring
2. Head plate
Over an extended period of time the spring steel spring
fatigues and the spring steel “fingers” begin to break
off. This creates irregular movement within the grinding
heads and will cause vibration when the machine is in
operation.
3. Cushion ring
4. Head mate
Routine checks for broken “fingers” in the spring steel
grinding heads are recommended. Life expectancy
for grinding heads can vary between 6 and 12 months
depending on the amount of usage.
Diagram 1. Spring Steel Head
4.
Replacement spring steel springs are available and can
be replaced without throwing the grinding head away.
1.
The spring steel heads can also be made less flexible
by the addition of a second spring steel spring.
3.
2.
Diagram 2
Diagram 2
1. Spring steel springs
2. Bolts
1.
7.
8.
3. Silicone spring
4. Head mate
5. Cushion ring
6. Head buddy
7. Spacers
8. Head plate
3.
2.
4.
6.
5.
24 - English
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Grinding Heads Drive System
IMOPRTANT!
The grinder comes equipped with Dual Drive Technolo-
gy™. As the grinding discs are driven by the large mo-
tor via an internal belt, and because the belt is sealed
inside the machine, there is no maintenance regarding
this drive system until a major service (belt and bearing
replacement) is due. This is typically following 12-36
months of operation.
Lubrication of this system will cause dust to
build up in chain ring and drastically shorten
the life of both the chain ring and planetary
drive sprocket.
Diagram 2
Diagram 3
Planetary Drive System
The second component to the Dual Drive Technol-
ogy™ system is the planetary head drive system which
is powered by the secondary or small motor and
gearbox arrangement. This system is on the outside
of the machine and will require routine maintenance.
The planetary drive system can be seen as illustrated
diagram 1.
Diagram 1
1. Grinding heads motor
2. Motor terminal box
3. Machine cover
1.
2.
1.
2.
1. Planetary drive sprocket
4. Gearbox mounting bracket
5. Gearbox flange bracket
6. Gearbox
2. Gearbox flange bracket
Diagram 3
1. Machine cover
2. Chain ring
7. Motor terminal box
8. Planetary drive motor
Diagram 4
1.
1. Planetary seal
As the chain ring and planetary drive sprocket are
located beneath the cover of the machine, yet on the
outside of the machine, there lies the potential that
they can be exposed to dust and other debris created
during the grinding process.
8.
7.
To prevent this as much as possible, a planetary seal
has been installed to stop dust and other particles from
coming into contact with the planetary drive mecha-
nism.
6.
3.
Diagram 4
2.
4.
5.
1.
Diagram 1. Planetary Drive System
Planetary seal - closeup
Beneath the gearbox and concealed by the mounting
brackets and machine cover, there is a planetary drive
sprocket situated on the output shaft of the gearbox.
This planetary sprocket engages with the chain ring
(also
located beneath the machine cover) and
together form the main drive mechanism for the plan-
etary drive system. This system is a dry system (i.e. it
is not required for there to be lubrication between the
planetary drive sprocket and chain ring), to allow any
dust that may come into contact with the chain ring to
fall back out again.
English - 25
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
The effectiveness of the planetary seal can be moni-
tored by the simple removal of the planetary motor
/ gearbox system by removing the four bolts shown
below.
Remove 2 bolts either
side.
Remove this bolt.
Remove 2 bolts either
side.
Remove cover off motor
terminal box.
Inspect for dust build
up here
Remove these bolts.
If the planetary seal is working effectively, there should
be a very minimal amount of dust observed under
the cover of the machine. If there is a build-up of 5-
6mm (1/4 inch), then it is more than likely it is time to
remove the machine cover and check the condition of
the planetary seal.
Remove this bolt.
Lift off machine cover to reveal chain ring and planetary
seal.
If planetary seal is worn or needs replacement, contact
your Husqvarna Construction Products distributor for a
new planetary seal replacement kit.
26 - English
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance schedule
Maintenance schedule
Item
Action
Frequency
Check that head locks
are tight.
Tighten head locks and re-set in thread-locking com-
pound if required (Suggested thread-locking compound
Loctite 680)
Daily
Inspect heads for slop/ Examine machine heads while machine tipped back.
Daily
broken “fingers” if using Disconnect Planetary Drive motor (small motor) and run
spring steel heads.
discs at lowest speed. Check to see how concentric/true
grinding heads are running.
Check effectiveness of Remove planetary head motor/gearbox system and
Weekly
planetary seal.
check for presence of dust under machine cover .
Check condition of
chain ring.
Remove planetary head motor/gearbox system and in-
spect chain links in chain ring. Ensure links are clean and
free from build-up.
Weekly with Planetary Seal
Check condition of
Drive Sprocket.
Remove planetary head motor/gearbox system and
inspect condition of planetary drive sprocket.
Weekly with Planetary Seal
6 monthly
Inspect internal compo- Remove belt tensioner cover plate and check inside
nents of machine.
machine for dust, moisture or belt fragments. Ensure to
re-seal cover plate with silicone sealant.
Clean contents of elec- Blow out inside of electrical cabinet and variable speed
trical cabinet. drives or frequency converters with DRY compressed air.
Every 2 months
IMOPRTANT!
Prior to removing belt tensioner cover plate,
ensure cover plate and area surrounding cover
plate are totally clean. Avoid debris from enter-
ing into inside of machine.
English - 27
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
Technical Data
Grinding width
PG 820
820mm (32")
PG 680
680mm (27")
Grinding disc
3x270mm (10.5")
440kg (970lbs)
335kg (737lbs)
112kg (246lbs)
3x240mm (9.5")
385kg (850lbs)
300kg (660lbs)
100kg (220lbs)
Weight
Grinding pressure total
Grinding pressure per disc
Motor Power
3-Phase 380-480V
12.5kW(17.0hp)
3-Phase 380-480V
12.5kW(17.0hp)
Power per grinding disc
Grinding disc speed
Planetary head speed
Direction of rotation
4.15kW (5.7hp)
250 - 1100rpm
5 - 65rpm
4.15kW(5.7hp)
600 - 1200rpm
5 - 70rpm
Independent FWD/REV direction control
on both grinding discs and planetary head.
Power supply
3 phase
3 phase
28 - English
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
EC-declaration of conformity
(Applies to Europe only)
Husqvarna Construction Products, SE-433 81 Göteborg, Sweden, tel: +46-31-949000, declares under sole responsibil-
ity that the Husqvarna PG680/PG820 dating from 2007 serial numbers and onwards (the year is clearly stated on the
rating plate, followed by the serial number), complies with the requirements of the COUNCILíS DIRECTIVE:
- of June 22, 1998 ”relating to machinery” 98/37/EC, annex IIA.
- of May 3, 1989 ”relating to electromagnetic compatibility” 89/336/EEC, and applicable supplements.
- of December 12, 2006 ”relating to electrical equipment” 2006/95/EC.
The following standards have been applied: EN 55014-1, EN55014-2, EN61000-3-2, EN61000-3-3.
The supplied machine conforms to the example that underwent EC type examination.
Göteborg 16 July 2007
Tim Van Der Veen, Development Manager
English - 29
Download from Www.Somanuals.com. All Manuals Search And Download.
www.husqvarnacp.com
1150943-20
´®z+R~@¶0R¨
´®z+R~@¶0R¨
2007-08-23
Download from Www.Somanuals.com. All Manuals Search And Download.
|