ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
MB517-01 • 03/10/15 • © Hunter Fan Company
Table of Contents
Congratulations on purchasing
What to Expect with
Your Installation
Tools Needed
Mounting Options
Ceiling Bracket
your new Hunter® ceiling fan! It will
provide comfort and performance
in your home or office for many
years. This installation and operation
manual contains complete
instructions for installing and
operating your fan.
2
3
7
4
5
We are proud of our work and
appreciate the opportunity to
supply you with the best ceiling fan
available anywhere in the world.
Preparation
Downrod
Wiring
Canopy
6
10
12
Operation, Maintenance
& Cleaning
Blades
Switch Housing
Light Kit
Troubleshooting
?
?
?
13
14
15
17
19
1
Download from Www.Somanuals.com. All Manuals Search And Download.
MB517-01 • 03/10/15 • © Hunter Fan Company
What to Expect with Your Installation
Read and Save These Instructions
This product conforms to UL Standard 507.
If you are unfamiliar
with wiring, use a
qualified electrician.
WARNINGS
w.1 - To reduce the risk of fire, electrical shock, or personal
injury, mount fan directly from building structure and/or
an outlet box marked acceptable for fan support of 70 lbs
(31.8 kg) and use the mounting screws provided with the
outlet box.
,8 Meters
(30 inches)
from blade tip
to nearest wall
or obstruction
2,1 Meters
(7 feet)
from bottom
edge of blade
to the floor
w.2 - To avoid possible electrical shock, before installing
or servicing your fan, disconnect the power by turning
off the circuit breakers to the outlet box and associated
wall switch location. If you cannot lock the circuit breakers
in the off position, securely fasten a prominent warning
device, such as a tag, to the service panel.
Must be able to
secure the fan to
building structure or
fan-rated outlet box
Know your wiring
Assess location
w.3 - To reduce the risk of fire, electrical shock, or motor
damage, use only Hunter Solid State Speed Controls.
w.4 - To reduce the risk of personal injury, do not bend the
blade brackets when installing the blade brackets, balancing
the blades, or cleaning the fan. Do not insert foreign objects in
between rotating fan blades.
You may need a
friend to help you.
Standard Downrod
1
2
for ceilings 2,4-3 m (8-10 feet) high
w.5 - This product is not intended to be used by people
(including children) whose physical, sensory, or mental
capacities are different or diminished, or lack of experience
or knowledge, unless such persons receive training or work
under supervision of a person responsible for their safety.
Ceiling angles greater
than 34° will require an
Angled Mounting Kit.
See page 4 for details.
Longer Downrod
for ceilings 3 m (10 feet) or higher
w.6 - Children should be supervised to ensure they do not use
the devices as a toy.
CAUTIONS
c.1 - All wiring must be in accordance with national and local
electrical codes ANSI/NFPA 70. If you are unfamiliar with
wiring, use a qualified electrician.
Check box to see
fan weight
Assess ceiling angle
Select a downrod length
c.2 - Use only Hunter replacement parts.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
MB517-01 • 03/10/15 • © Hunter Fan Company
Tools Needed
Pliers
Wire Strippers
Screwdrivers
Ladder
9/64” Drill Bit
(optional)
Power Drill
(optional)
If mounting to a support structure, you will also need these tools.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
MB517-01 • 03/10/15 • © Hunter Fan Company
O
34
CEILING
Mounting Options
If you have a flat ceiling:
Hang your fan by a standard downrod (included).
Standard
Mounting
Support
Structure
Support
Structure
If you have an angled ceiling:
Ceiling
Outlet Box
(required)
1. You will need a longer downrod (included).
Angled
Mounting
2. If your ceiling angle is greater than 34°, you will
also need an Angled Mounting Kit (sold separately).
Ceiling
Outlet Box
(required)
Standard
Mounting
Style
Angled
Mounting
Style
Use the three steps below to determine if your ceiling angle is greater than 34°
1
2
3
34°
PLACE
SLIDE
toward ceiling
FOLD
against wall
on dotted line
Guide Touches
BOTH Ceiling & Wall
Guide Touches
but NOT Ceiling
Wall
Use Standard Mounting to hang
Use Angled Mounting to
hang the fan from a vaulted or
angled ceiling.
the fan from a flat ceiling.
You need ONLY
a Longer
You need BOTH
a Longer
Downrod
Downrod &
an Angled
*most common
Mounting Kit
4
Download from Www.Somanuals.com. All Manuals Search And Download.
MB517-01 • 03/10/15 • © Hunter Fan Company
Ceiling Bracket
For angled ceilings, point
opening toward peak.
OFF
Use wood screws
(included) when securing
to support structure with
Use machine screws
(provided with outlet
box) when securing to
Make sure all four (4) bumpers
are still attached.
approved electrical outlet existing ceiling fan-rated
box. Drill 9/64” pilot holes
in support structure to aid
outlet box. Make sure
it is securely installed
in securing ceiling bracket and is acceptable for fan
with hardware found in support of 31.8 kg (70 lbs)
or less.
the hardware bag.
To avoid possible electrical shock, before
installing your fan, disconnect the power by
turning off the circuit breakers to the outlet
box associated with the wall switch location.
Refer to warning w.1 on pg. 2
5
Download from Www.Somanuals.com. All Manuals Search And Download.
MB517-01 • 03/10/15 • © Hunter Fan Company
Preparation
Ceiling Bracket (continued)
Remove the shipping blocks from the
motor. Discard the screws.
Note: Some fans will have a shipping
ring instead of shipping blocks. Please
remove the ring and discard the screws.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
MB517-01 • 03/10/15 • © Hunter Fan Company
Downrod
Standard Downrod
for ceilings 2,4-3 m
(8-10’) high
skip to next page
If you need a different downrod length follow these steps:
Steps 1-5 to remove standard downrod pipe
Longer Downrod
for angled
ceilings or
1
2
3
4
5
ceilings 3 m (10’)
or higher
10
9
8
7
6
Steps 6-10 to reassemble with new pipe
7
Download from Www.Somanuals.com. All Manuals Search And Download.
MB517-01 • 03/10/15 • © Hunter Fan Company
Downrod (continued)
1 cm
(3/8”)
20 cm
(8”)
Remove the pre-installed
setscrew so that the downrod
can be inserted.
Hand tighten the downrod (at
least 4-5 full turns) until it stops.
The wires can be cut, but
Tighten the setscrew
with pliers. DO NOT
HAND TIGHTEN.
leave at least 20 cm (8”)
extending from the top of
the downrod.
20 cm
(8”)
1 cm
(3/8”)
If the setscrew is not tightened
securely, the fan may fall.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
MB517-01 • 03/10/15 • © Hunter Fan Company
Downrod (continued)
Put the wires and downrod through the canopy.
Let the canopy sit loosely on top of the fan.
DO NOT PICK THE FAN UP BY THE CANOPY
OR WIRES. Place the downrod ball into the slot
in the ceiling bracket.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
MB517-01 • 03/10/15 • © Hunter Fan Company
Wiring
Note: To connect the wires, hold
the bare metal leads together and
place a wire connector over them,
then twist clockwise until tight.
C
Receiver
Using an orange wire connector
from the hardware bag:
Connect the 3 grounding wires
(green, green/yellow stripe, or bare
copper) coming from the ceiling,
downrod, and ceiling bracket.
green/yellow stripe
Place the receiver on top of the downrod
assembly as shown.
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
10
Download from Www.Somanuals.com. All Manuals Search And Download.
MB517-01 • 03/10/15 • © Hunter Fan Company
Wiring (continued)
C
Using the orange wire connectors from
the remote control hardware bag:
Using the orange wire connectors
from the hardware bag:
•
Connect the yellow wire from the
receiver to the black wire from the
fan.
•
Connect the black (ungrounded)
wire from the ceiling to the black
wire from the receiver.
white
•
Connect the blue wire from the
receiver to the blue wire (or
possibly black with white stripe
wire) from the fan.
•
Connect the white (grounded)
wire from the ceiling to both the
white wire from the receiver and
the white wire from the fan.
M
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
11
Download from Www.Somanuals.com. All Manuals Search And Download.
MB517-01 • 03/10/15 • © Hunter Fan Company
Canopy
Screw
holes
Position the canopy so that, when
lifted into place, the canopy fits into
Lift the canopy into place so that
the screw holes are aligned.
Insert the two canopy screws
found in the hardware bag.
the hanging bracket as shown.
Note: Fan style may vary.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
MB517-01 • 03/10/15 • © Hunter Fan Company
Blades
Put the blade washers, found in the
hardware bag, onto the blade screws, found
in the hardware bag. Then install the blade
screws to secure each blade to a blade iron.
Lightly attach the blade irons to the motor
with screws found in the hardware bag, then
securely tighten after both screws are attached.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
MB517-01 • 03/10/15 • © Hunter Fan Company
Switch Housing
Feed the wire plug through the center
hole of the upper switch housing, then
wrap keyhole slots around the screws and
twist counterclockwise.
Screw two housing assembly screws
Insert the third screw, found in the
hardware bag, into place and then
tighten all three screws.
from the hardware bag halfway into
the motor housing. It does not matter
which two screw holes you choose.
Make sure the upper switch housing is securely
attached to the mounting plate. Failure to properly
secure all 3 assembly screws could result in the switch
housing fixture falling.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
MB517-01 • 03/10/15 • © Hunter Fan Company
Light Kit
Switch
Housing
Screw
Align the keyhole slots in the light kit
housing with the housing assembly
screws. Make sure all the wires from the
fan and the light kit are snug inside the
center of the light kit, not pinched in
between the upper switch housing and
the light kit or hanging out of the sides.
Turn the light kit counterclockwise until
Partially install two of the switch housing
screws found in the bag. Connect
the plugs from the upper and lower
switch housings. Make sure to line up the
colored markings on the connectors.
the housing assembly screws are firmly
situated in the narrow end of the keyhole
slots. Install the remaining screw into the
housing. Tighten all three screws securely.
Make sure the lower switch housing is securely attached to
the upper switch housing. Failure to properly secure all three
assembly screws could result in the light fixture falling.
Note: Globe style and number of
lights may vary.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
MB517-01 • 03/10/15 • © Hunter Fan Company
Light Kit (continued)
Tab
Notch
Bulb
Install a bulb into each of the sockets.
When necessary, replace with bulbs of
the same type and wattage.
Lift the globe and align the notches in the
globe with the tabs in the light kit. Attach
the glass bowl to the light kit by twisting it
clockwise until it snaps into place.
See next page for fan
operation instructions.
Note: In compliance with US federal energy regulations, this ceiling fan
contains a device that restricts its light output. Exceeding the wattage
limit marked on the MAX wattage sticker affixed to the light socket(s)
may result in fire hazard or improper operation.
Note: Globe style and number of
lights may vary.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
MB517-01 • 03/10/15 • © Hunter Fan Company
Operation, Maintenance, & Cleaning
Medium
Speed
Fan
Off
High
Speed
Switch Cover
Plate
Battery
Door
Low
Speed
Light
Phillips
Head
Screw
Rocker- Style
Plate
Removed
Tabs
To access the battery compartment,
remove the small Phillips head screw
that secures the battery door to the
transmitter assembly. The battery
should be installed with the positive
(+) side up. Replace with a CR2032
battery when necessary.
The remote transmitter should already be
paired to the receiver and ready to use.
To turn on fan, press a fan speed
button. Speeds range from off (0)
to high (3). Quickly press the Light
button to turn the lights off and on.
Hold the Light button to raise and
dim the light level.
To install the transmitter cradle, remove
the two screws holding the switch
cover plate. Do not remove the cover
plate. Orient the cradle by lining up
the two mounting holes with those on
the cover plate. Insert and tighten the
screws. Do not over tighten.
Note: If your need to pair your remote,
turn fan power off and back on at the wall
switch. Within 3 minutes, press and hold
both the Fan Off button and the High
button for 4 seconds to pair the remote.
To prevent faulty operation, please
ensure all other ceiling fans within
range are turned off at the wall switch
while pairing.
Note: For rocker-style cover plates,
break off the tabs by pushing outward.
Turn Power
ON
17
Download from Www.Somanuals.com. All Manuals Search And Download.
MB517-01 • 03/10/15 • © Hunter Fan Company
Operation, Maintenance, & Cleaning (continued)
Safe-Exit
The Safe-Exit Program gives
you about thirty seconds of light
when you turn the lights off to
exit the room before the lights go
out.To use Safe-Exit:
• Press the Fan Off button for at
least three seconds to initiate the
Safe-Exit Mode.
Reverse
Switch
• The lights will flash for visual
confirmation.
• The lights will stay on 50%
brightness for 15 seconds and
then begin to dim. After a total
of 30 seconds, the lights will be
completely off.
To switch the direction of air flow, move
the reverse switch to the opposite
position. You will need to remove the
light kit glass to do so.
For cleaning the fan, use soft brushes or
cloths to prevent scratching. Cleaning
products may damage the finishes.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
MB517-01 • 03/10/15 • © Hunter Fan Company
Troubleshooting
Fan doesn’t work
Noisy Operation
Lights dim when turned on or
do not turn on at all.
Excessive wobbling
• Make sure power switch is on.
• Tighten the blade and blade
iron screws until they are snug.
• Tighten all of the blade and
blade iron screws until they
are snug.
• Make sure the wattage of the
light bulbs installed matches
the specifications on the light
sockets.
• Pull the pull chain to make sure
it is on.
• Check to see if any of the
blades are cracked. If so, replace
all of the blades.
• Turn the power off, support
the fan carefully, and check
that the hanger ball is
properly seated.
•
Push the motor reversing switch
firmly left or right to ensure that
it is engaged.
• Check the circuit breaker to
ensure the power is turned on.
• Use the provided balancing
kit and instructions to balance
the fan.
• Make sure the blades spin freely.
• Turn off power from the circuit
breaker, then loosen the canopy
and check all the connections
according to the wiring diagram
on pages 10-11.
If you have multiple remotes or
multiple remote-controlled fans
installed on the same circuit
breaker and you are experiencing
interference or faulty operation of
your remote controls, please go to
and click “How do I properly install
multiple remote-controlled fans?”
for information on how to correct
this issue.
Remote control of fan is erratic
• Make sure the battery is
installed correctly.
• Install a fresh battery.
• Check the plug connection in
the switch housing.
Transmitter only works when
held at close range
•
Install a fresh battery.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
MB517-01 • 03/10/15 • © Hunter Fan Company
|