Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
900 Series™ Introduction
1
GPS Receiver Installation
25
Stem Mounting with an Existing 1" - 14 Thread Stem .............................................. 26
Access Under Mounting Location................................................................................ 27
No Access Under Mounting Location.......................................................................... 27
Finish Routing the Cable and Check GPS Receiver Operation .................................. 28
How Sonar Works .......................................................................................................... 1
DualBeam PLUS™ Sonar .............................................................................................. 2
QuadraBeam PLUS™ Sonar
(Standard with 957c Combo models, optional-purchase for 917c Combo models only) ........
3
Universal Sonar 2 ............................................................................................................ 3
How GPS and Cartography Work .................................................................................. 3
Multi-Media Card (MMC)/SD Slot.................................................................................. 5
Software Updates............................................................................................................ 5
Accessory Bus .................................................................................................................. 5
Testing the System Installation
29
Getting Started - Using Your 900 Series™
30
Powering Up the Control Head .................................................................................... 30
What’s on the Sonar Display ...................................................................................... 31
Understanding Sonar History ...................................................................................... 32
Real Time Sonar (RTS®) Window.................................................................................. 32
Bottom Presentation...................................................................................................... 32
Installation Overview
5
6
Control Head Installation
Key Functions
33
Gimbal Mounting the Control Head .............................................................................. 7
Connecting the Control Head Power Cable to the Boat ............................................ 11
POWER/LIGHT Key ........................................................................................................ 33
VIEW Key........................................................................................................................ 34
MENU Key ...................................................................................................................... 34
4-WAY Cursor Control Key ............................................................................................ 35
View Preset Keys............................................................................................................ 35
EXIT Key.......................................................................................................................... 35
INFO Key ........................................................................................................................ 36
MARK Key ...................................................................................................................... 36
GOTO Key........................................................................................................................ 36
ZOOM (+/-) Keys............................................................................................................ 37
Transducer Installation
12
Transom Transducer Installation .................................................................................. 13
Inside the Hull Transducer Installation ...................................................................... 21
Trolling Motor Transducer Installation ........................................................................ 24
Trolling Motor Transducer Options .............................................................................. 25
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
531553-1_B
Table of Contents
Views
37
The Menu System
60
61
Views and Readouts...................................................................................................... 37
Sonar View .................................................................................................................... 38
Sonar Zoom View .......................................................................................................... 39
Split Sonar View ............................................................................................................ 40
Snapshot and Recording View...................................................................................... 41
Side Beam View (with QuadraBeam PLUS™ only) .......................................................... 45
Bird’s Eye View .............................................................................................................. 47
Chart/Bird’s Eye Combo View ...................................................................................... 48
Chart/Chart Combo View .............................................................................................. 49
Chart View...................................................................................................................... 50
Chart/Sonar Combo View.............................................................................................. 51
Chart Orientation .......................................................................................................... 52
Start-Up Options Menu
Normal Operation .......................................................................................................... 62
Simulator ...................................................................................................................... 62
System Status .............................................................................................................. 62
Self Test .......................................................................................................................... 63
Accessory Test................................................................................................................ 63
GPS Diagnostic View .................................................................................................... 64
Sonar X-Press™ Menu
65
Active Side...................................................................................................................... 65
Split Position .................................................................................................................. 66
Sensitivity ...................................................................................................................... 66
Upper Range
(Advanced: Sonar, Split Sonar and Active Sonar Side Views only) .................................... 67
Lower Range ................................................................................................................ 67
Chart Speed .................................................................................................................. 68
Viewing Cartography
Navigation
52
53
Quad Layout
Waypoints, Routes and Tracks...................................................................................... 54
Save, Edit, or Delete a Waypoint.................................................................................. 55
Navigate to a Waypoint or Position.............................................................................. 56
Add a Waypoint Target or Trolling Grid........................................................................ 56
Save, Edit or Delete a Route ........................................................................................ 57
Save or Clear a Current Track ...................................................................................... 58
Edit, Delete or Hide Saved Tracks ................................................................................ 58
Man Overboard (MOB) Navigation .............................................................................. 59
(with QuadraBeam PLUS™ Transducer, Side Beam View only)...................................... 68
Bottom Lock (Sonar Zoom View only) ............................................................................ 69
Bottom Range (Sonar Zoom View only, when Bottom Lock is on).................................... 69
Sonar Colors .................................................................................................................. 69
Cancel Navigation (only when navigating)...................................................................... 69
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Delete All Recordings
Navigation X-Press™ Menu
70
(optional-purchase MMC/SD Card, Snapshot and Recording View only).......................... 77
Active Side...................................................................................................................... 70
Split Position .................................................................................................................. 70
Waypoint [Name] (Only with an active cursor on a waypoint) ............................................ 71
Cursor to Waypoint (Chart or Combo view only) .................................................................. 71
Save Current Track ........................................................................................................ 72
Clear Current Track ........................................................................................................ 72
Save Current Route (Only when navigating) .................................................................. 72
Skip Next Waypoint (Only when navigating) .................................................................. 72
Cancel Navigation (Only when navigating) .................................................................... 73
Cancel MOB Navigation (only when MOB Navigation is activated) ................................ 73
Remove Target (Only if a Target is active) ........................................................................ 73
Remove Grid (Only if a Grid is active) .............................................................................. 73
Waypoint Name (Most recently-created waypoint).......................................................... 74
Pings Per Second
(optional-purchase MMC/SD Card, Snapshot and Recording View only).......................... 78
Playback Speed
(optional-purchase MMC/SD Card, Snapshot and Recording View only).......................... 78
Stop Playback (optional-purchase MMC/SD Card only) ........................................................ 79
Sonar Menu Tab
79
Beam Select .................................................................................................................. 80
Fish ID+™ ...................................................................................................................... 80
Fish ID Sensitivity .......................................................................................................... 81
Real Time Sonar (RTS®) Window.................................................................................. 82
Bottom View .................................................................................................................. 82
Zoom Width (Sonar Zoom View only) .............................................................................. 82
83 kHz Sensitivity .......................................................................................................... 83
455 kHz Sensitivity
Snapshot and Recording X-Press™ Menu (Snapshot and Recording View only) 75
Start Recording
(Advanced, with QuadraBeam PLUS™ transducer, optional-purchase for the 917) ........ 83
Depth Lines (Advanced) .................................................................................................. 84
Surface Clutter (Advanced) ............................................................................................ 84
Noise Filter (Advanced).................................................................................................... 85
Max Depth (Advanced).................................................................................................... 85
Water Type (Advanced) .................................................................................................. 86
Transducer Select .......................................................................................................... 86
Color Bar ........................................................................................................................ 86
Temperature (Sonar View only, with Temperature input) ................................................ 87
(optional-purchase MMC/SD Card, Snapshot and Recording View only).......................... 75
Stop Recording (optional-purchase MMC/SD Card only) ...................................................... 75
Delete Image
(optional-purchase MMC/SD Card, Snapshot and Recording View only).......................... 76
Delete All Images
(optional-purchase MMC/SD Card, Snapshot and Recording View only).......................... 76
Delete Recording
(optional-purchase MMC/SD Card, Snapshot and Recording View only).......................... 77
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Set Simulation Position (Advanced) .............................................................................. 96
Set Map Offset (Advanced) ............................................................................................ 96
Clear Map Offset (Advanced).......................................................................................... 97
Navigation Menu Tab
87
Current Track .................................................................................................................. 88
Saved Tracks .................................................................................................................. 88
Waypoints ...................................................................................................................... 89
Routes ............................................................................................................................ 89
Chart Orientation .......................................................................................................... 90
North Reference ............................................................................................................ 90
Trolling Grid Rotation .................................................................................................... 91
Trackpoint Interval.......................................................................................................... 91
Track Min Distance (Advanced) ...................................................................................... 91
Track Color Range.......................................................................................................... 92
Map Datum (Advanced) .................................................................................................. 92
Course Projection Line .................................................................................................. 92
Export All Nav Data (Advanced) .................................................................................... 92
Delete All Nav Data (Advanced) .................................................................................... 93
Continuous Navigation Mode ...................................................................................... 93
Alarms Menu Tab
97
Depth Alarm .................................................................................................................. 98
Fish ID Alarm.................................................................................................................. 98
Low Battery Alarm ........................................................................................................ 98
Aux Temp Alarm (with optional-purchase temp. probe or Temp/Speed only)...................... 99
Temp Alarm .................................................................................................................... 99
Off Course Alarm ........................................................................................................ 100
Arrival Alarm ................................................................................................................ 100
Drift Alarm.................................................................................................................... 101
Alarm Tone .................................................................................................................. 101
Setup Menu Tab
102
Units - Depth................................................................................................................ 102
Units - Temp (International only).................................................................................... 102
Units - Distance (with Speed input only) ...................................................................... 103
Units - Speed (with Speed input only) .......................................................................... 103
User Mode.................................................................................................................... 103
Language (International only) ........................................................................................ 103
Triplog Reset (with Speed input only) ............................................................................ 104
Restore Defaults .......................................................................................................... 104
Select Readouts (Advanced) ........................................................................................ 104
Chart Menu Tab
93
Chart Detail Level .......................................................................................................... 94
Map Borders .................................................................................................................. 94
Lat/Lon Grid.................................................................................................................... 95
Spot Soundings.............................................................................................................. 95
Navaids on Bird's Eye View .......................................................................................... 95
Shaded Depth ................................................................................................................ 95
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Depth Offset (Advanced) .............................................................................................. 106
Aux. Temp. Offset (Advanced) ...................................................................................... 106
Temp Offset (Advanced) ................................................................................................ 106
Speed Calibration (Advanced, with Speed paddlewheel only) ...................................... 107
Local Time Zone (Advanced) ........................................................................................ 107
Daylight Saving Time (Advanced) ................................................................................ 107
Position Format (Advanced) .......................................................................................... 107
Time Format (Advanced, International only) .................................................................. 108
Date Format (Advanced, International only) .................................................................. 108
Digits Format (Advanced) ...................................................................................................... 109
NMEA Output (Advanced) ............................................................................................ 109
Sonar ............................................................................................................................ 110
1-Year Limited Warranty
Humminbird® Service Policy
900 Series™ Accessories
Specifications
117
117
119
121
122
133
Glossary
Contact Humminbird®
Views Menu Tab
110
112
NOTE: Entries in this Table of Contents which list (International only) are only
available on products sold outside of the US and Canada by our authorized
International Distributors. To obtain a list of authorized International Distributors,
please visit our website at www.humminbird.com or contact our Customer
Resource Center at 1-800-633-1468 to locate the distributor nearest you.
Accessories Menu Tab
Using Screen Snapshot .............................................................................................. 112
Troubleshooting 114
900 Series™ Doesn’t Power Up.................................................................................. 114
900 Series™ Defaults to Simulator with a Transducer Attached ............................ 114
NOTE: Entries in this Table of Contents which list (with Speed Input) or (with
Temperature Input) may require the purchase of separate accessories. You can
visit our website at www.humminbird.com to order these accessories online or
contact our Customer Resource Center at 1-800-633-1468.
Display Problems
115
116
Finding the Cause of Noise
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
SONAR is an acronym for SOund and
NAvigation Ranging. Sonar utilizes precision
sound pulses or "pings" which are emitted into
the water in a teardrop-shaped beam.
900 Series™ Introduction
Your 900 Series™ Ultra Wide Screen Fishing System comes in several
different configurations. See the following list of products, all of which are
covered by this manual, to find your 900 Series™ configuration:
The sound pulses "echo" back from objects in
the water such as the bottom, fish and other
submerged objects. The returned echoes are
displayed on the LCD screen. Each time a new
echo is received, the old echoes are moved
across the LCD, creating a scrolling effect.
• Humminbird® 917c Combo: Ultra Wide Screen Fishing System with
Chartplotter (Maps) and DualBeam PLUS™ 200/83 kHz Transducer,
GPS Receiver included
• Humminbird® 957c Combo: Ultra Wide Screen Fishing System with
Chartplotter (Maps) and QuadraBeam PLUS™ 200/83/455 kHz
Transducer, GPS Receiver included.
How Sonar Works
When all the echoes are viewed side by side,
an easy to interpret "graph" of the bottom, fish
and structure appears.
Sonar technology is based on sound waves. The 900 Series™ Fishing System
uses sonar to locate and define structure, bottom contour and composition,
as well as depth directly below the transducer.
Your 900 Series™ Fishing System sends a sound wave signal and determines
distance by measuring the time between the transmission of the sound
wave and when the sound wave is reflected off of an object; it then uses the
reflected signal to interpret location, size, and composition of an object.
Sonar is very fast. A sound wave can travel from the surface to a depth of
240 ft (70 m) and back again in less than 1/4 of a second. It is unlikely that
your boat can "outrun" this sonar signal.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
The sound pulses are transmitted at various
frequencies depending on the application.
Very high frequencies (455 kHz) are used for
greatest definition but the operating depth is
limited. High frequencies (200 kHz) are
commonly used on consumer sonar and
provide a good balance between depth
performance and resolution. Low frequencies
(83 kHz) are typically used to achieve greater
depth capability.
DualBeam PLUS™ Sonar
Your 900 Series™ Fishing System uses a
200/83 kHz DualBeam PLUS™ sonar system
with a wide (60°) area of coverage.
DualBeam PLUS™ sonar has a narrowly
focused 20° center beam, surrounded by a
second beam of 60°, expanding your
coverage to an area equal to your depth.
In 20 feet of water, the wider beam covers
an area 20 feet wide. The 20° center beam is
focused on the bottom, to show you
structure, weeds and cover. The 60° wide
beam is hunting for fish in the wide
coverage area. DualBeam PLUS™ sonar
returns can be blended together, viewed
separately or compared side-by-side.
DualBeam PLUS™ is ideal for a wide range
of conditions - from shallow to very deep
water in both fresh and salt water. Depth
capability is affected by such factors as boat
speed, wave action, bottom hardness, water
conditions and transducer installation.
The power output is the amount of energy
generated by the sonar transmitter. It is
commonly measured using two methods:
• Root Mean Square (RMS) measures power
output over the entire transmit cycle.
• Peak to Peak measures power output at the
highest points.
The benefits of increased power output are
the ability to detect smaller targets at greater
distances, ability to overcome noise, better
high speed performance and enhanced depth
capability.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
QuadraBeam PLUS™ Sonar
(Standard with 957c Combo models, optional-
purchase for 917c Combo models only)
Universal Sonar 2
Your 900 Series™ Fishing System supports Universal Sonar 2, a state-of-the-
art, integrated and protected transducer that is built into the lower unit of
Minnkota trolling motors. With Universal Sonar 2, all wiring is concealed
inside the indestructible composite shaft—out of sight and out of harm’s
way, with no clamps, ties, or exposed wires. Universal Sonar 2 features new
temperature sensing and the performance of DualBeam PLUS™ technology.
An expanded view and greater bottom detail gives you a totally new
perspective of the water below, along with optimal sonar performance to
help you find fish.
Your 900 Series™ 957c Combo is
shipped with a QuadraBeam PLUS™
transducer. QuadraBeam PLUS™ sonar
provides an extremely wide (90°) area
of coverage. QuadraBeam PLUS™
starts with two fan-shaped 35° 455 kHz
Side Structure locating sonar beams to
spot fish, bait and structure to the left
and right of the boat over an area of the
bottom that’s always equal to twice
your depth.
How GPS and Cartography Work
Your 900 Series™ Fishing System also supports GPS and chartplotting, and
uses GPS and sonar to determine your position, display it on a grid, and
provide detailed underwater information. The Global Positioning System
(GPS) is a satellite navigation system designed and maintained by the U.S.
Department of Defense. GPS was originally intended for military use;
however, civilians may also take advantage of its highly accurate position
capabilities, typically within +/- 10 meters, depending on conditions. This
means that 95% of the time, the GPS receiver will read a location within 10
meters of your actual position. Your GPS Receiver also uses information from
WAAS (the Wide Area Augmentation System), EGNOS (the European
Geostationary Navigation Overlay Service), and MSAS (the MTSAT Satellite
Augmentation System) satellites if they are available in your area.
For a detailed view below the boat, QuadraBeam PLUS™ uses DualBeam
PLUS™ technology, with precision 20° and wide 60° beams. QuadraBeam
PLUS™ finds more fish faster, and can even tell you where to put your bait
by showing if fish are to the left, right or directly beneath your boat.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
GPS uses a constellation of 24 satellites that
continually send radio signals to the earth.
Your present position is determined by
receiving signals from up to 16 satellites and
measuring the distance from the satellites.
The following GPS functionality is currently supported by the 900 Series™
Fishing System when it is connected to the included GPS receiver:
• View current position
• View current track (breadcrumb trail)
• View precision speed and heading from your GPS receiver
• Save tracks, waypoints and routes
• Travel a route and navigate from one waypoint to the next.
All satellites broadcast a uniquely coded signal once per second at exactly the
same time. The GPS receiver on your boat receives signals from satellites that
are visible to it. Based on time differences between each received signal, the
GPS receiver determines its distance to each satellite. With distances known,
the GPS receiver mathematically triangulates its own position. With once per
second updates, the GPS receiver then calculates its velocity and bearing.
Your 900 Series™ supports Navionics® Gold, HotMaps™ and HotMaps™
Premium on MMC or SD card media.
NOTE: Your 900 Series™ does not support Navionics® Classic Charts, only
Navionics® Gold, HotMaps™, and HotMaps™ Premium.
Your unit also comes with a built-in UniMap™ with a more detailed map of
North America (Domestic models) or a more detailed map of Europe and
Southeast Asia, including Australia and New Zealand (International models).
The GPS Receiver included with your 900 Series™ Fishing System allows you
to combine easy-to-use FishingGPS® chartplotter and navigation capabilities
with advanced fishfinding.
Your 900 Series™ uses the GPS Receiver to determine the position of the
boat automatically, and uses the zoom level settings on a particular view to
select the best chart to display. See Viewing Cartography for more
information.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Multi-Media Card
(MMC)/SD Slot
Accessory Bus
Use the Accessory Bus to expand the
functionality of your 900 Series™. Accessories
plug directly into the 900 Series™, enabling
Advanced features such as WeatherSense®
and the SmartCast® Wireless Sonar Link.
Additional tabs and menu choices will be
added to the menu system automatically when
an accessory is plugged into the unit. In
addition, multiple accessories can be attached
simultaneously. See Accessories Menu Tab
and 900 Series™ Accessories in this manual,
as well as your accessory Operations Manual
for additional details.
Your 900 Series™ Fishing System also has a
multi-media card (MMC)/SD slot that is used
to insert optional-purchase cards containing
additional detailed maps. If you insert an
MMC/SD that contains a more detailed
chart for a particular location, your 900
Series™ Fishing System will retrieve that
chart and display it automatically. Use the
Inserting an MMC/SD
into the Card Slot
Accessory Bus
illustration to locate the position of the MMC/SD slot cover, remove the
MMC/SD slot cover, then insert the MMC/SD into the slot. The label on the
MMC/SD should face toward the left side of the unit. Press down on the
card until it clicks into place and replace the slot cover. Then, replace and
tighten snugly - do NOT overtighten, as this will not improve water
resistance, and may damage the cover.
NOTE: Accessories to enable WeatherSense® and the SmartCast® Wireless
Sonar Link require separate purchases. You can visit our website at
www.humminbird.com or contact our Customer Resource Center at
1-800-633-1468 for additional details.
Software Updates
Use the MMC/SD slot to update the software version of your control head.
To update the software in your control head, plug in the appropriate
MMC/SD card that contains a software update file; the unit will recognize it,
will tell you what software version your control head is currently running,
and will ask you if you want to update the software in the unit to match that
on the MMC/SD card. You can obtain software updates from the
www.humminbird.com website.
Installation Overview
Please read all instructions that are relevant for your configuration before
beginning the installation process.
NOTE: Installation procedures will depend on product configuration.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Inside the boat there is often a channel or conduit used for other wiring, this
can be used to route cables. Be sure to route the cable as far as practical
from the antenna cable of VHF radios or tachometer cables to reduce the
possibility of interference. The transducer and GPS receiver cables should
not be cut, and care should be used not to damage the cable insulation.
The 900 Series™ has a wide variety of configurations.
Basic installation tasks that you must perform include:
• Installing the control head (choosing either gimbal or in-dash
mounting, where in-dash mounting requires a separate purchase)
• Installing the transducer (choosing either the transom mount,
inside the hull mount, or trolling motor mounting method)
2
• Installing the GPS Receiver (if included)
1
• Testing the complete installation and locking the transducer position.
NOTE: Accessories may require a separate purchase. You can visit our website at
www.humminbird.com to order these accessories online or contact our
Customer Resource Center at 1-800-633-1468.
3
8
4
6
Control Head Installation
7
5
You have two choices for mounting your 900 Series™ control head, Gimbal
mounting, where you use a surface on the boat, such as the dash, to mount
the control head so that it can be tilted up or down, or In-dash mounting,
which requires a separate purchase.
Accessory Bus
Sonar Transducer w/Temperature
Optional “Y” Cable
Power
Speed through water
GPS Receiver
1
2
3
4
5
6
7
8
WeatherSense®
Temperature/Speed
SmartCast® Wireless Sonar Link
6
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Place the control head into the gimbal bracket. Make sure that the
straight side of the gimbal arm is against the back side of the control
head.
Gimbal Mounting the Control Head
If you are gimbal mounting the Humminbird® 900 Series™, you can pre-
assemble the unit in order to plan the best mounting location.
2. Place a 1" (25 mm) diameter black washer on the gimbal knob and
then thread the knob and washer into the housing. Tighten the
gimbal knob to secure the 900 Series™ control head to the mount.
Repeat step 2 for the other side.
1
You can now place the control head in various locations to decide which is
best for mounting. Rotating the mounting bracket to the top of the control
head will allow for overhead mounting. The chosen mounting area should
allow for sufficient room so the control head can pivot through the full tilt
range and allow for easy removal and installation.
2
3
NOTE: You can drill the cable pass hole underneath the gimbal bracket, allowing
you to thread the cables through the knock-out holes in the mount; however, if
you cannot drill the hole directly under the mounting bracket, then you will need
to drill the cable pass hole behind the bracket, and will need to mount the hole
cover there instead.
Washer
1
2
3
Gimbal Knob
Gimbal Bracket
NOTE: When drilling holes in fiberglass hulls, it is best to start with a smaller bit
and use progressively larger drill bits to reduce the chance of chipping or flaking
the outer coating. Fill all holes with marine grade silicone sealant.
In addition to the hardware supplied with your control head, you will need a
powered hand drill and various drill bits, various hand tools, including a Phillips
head screwdriver, a socket wrench and a flat head screwdriver, a marker or
pencil, safety glasses and dust mask, and marine-grade silicone sealant.
NOTE: You must have underside access to the mounting location to pass the
cables through to the surface. Also, make sure that the mounting surface is
adequately supported to protect the control head from excessive wave shock and
vibration and provide visibility while in operation.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
8.5"
5"
3. After the mounting location has been determined, loosen the gimbal
knobs and remove the control head from the gimbal bracket.
3.6"
NOTE: Alternate hole patterns are available on the gimbal mounting bracket, and
may match existing holes on the boat. You may choose to use one of these
alternate hole patterns.
1.25"
4. Place the gimbal bracket in the chosen position on the mounting
surface and mark the four mounting screw locations using a pencil
or center punch.
1
NOTE: Go to the installation instructions applicable to your transducer, GPS
Receiver and accessories. Make the required installations and then run the
cables to your control head mounting location. Do not cut any cabling (except the
power cable). If your cables are too short, extensions are available from your local
dealer or online from www.humminbird.com.
3
2
Mounting Screws
Washer
Gimbal Mounting Bracket
1
2
3
5. Set the gimbal bracket aside and drill the four mounting screw holes
using a 5/32" (4.0 mm) drill bit.
6a. If the cables must pass through a hole directly beneath the
mounting bracket, mark and drill an additional 1" (25 mm) hole
centered between the four mounting holes. Route the cables
through the 1" hole. Place the hole cover over the mounting surface
8
Download from Www.Somanuals.com. All Manuals Search And Download.
hole, then use it to mark the position of the two mounting screws.
Remove the hole cover, drill the two mounting holes using a 9/64"
bit. Do not install the hole cover at this time.
Cables Routed Directly Beneath Mounting Bracket
1
6b. If the cables cannot be routed directly beneath the mounting
bracket, mark and drill a 1" (25 mm) hole that will allow you to run
the cables close to the bracket. Pass the cables through the 1" (25
mm) hole, routing the cables through the grommet and pressing the
grommet into place. Place the hole cover over the mounting surface
hole, then use it to mark the position of the two mounting screws.
Remove the hole cover, drill the two mounting holes using a 9/64"
(3.5 mm) bit, fill them with marine-grade silicone, then replace the
hole cover and insert the #8 Phillips countersink wood screws.
Hand-tighten only.
2
7. Place the mounting bracket on the mounting surface aligned with
the drilled holes and fill the mounting holes with marine grade
silicone. Insert the four #10 Slotted-Hex wood screws into the
mounting holes. Hand-tighten only.
Gimbal Bracket
Hole Cover
1
2
8. If the cable pass through hole is beneath the mounting bracket, you
will need to install the hole cover. Place the hole cover over the
mounting bracket cable pass thru hole and align with holes drilled
in step 6a. Insert the #8 Phillips countersink wood screws. Hand
tighten only.
NOTE: Be sure that the cables pass through the slots on the hole cover and there is
enough cable slack to allow for the control head to pivot through its full tilt range.
Extra cable slack will also help when connecting/disconnecting the cables.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Cables Routed Behind Mounting Bracket
1
2
3
4
1
Power
1
2
3
4
5
Temp/Speed
Communications
Transducer
5
3
Cable Collector Insert
2
1
2
Gimbal Bracket
Grommet
1
4
2
3
Hole Cover
5
9. Insert cable connectors into the proper recesses on the cable
collector insert. The cable connectors are keyed to prevent reverse
installation, so be careful not to force the connectors into the wrong
slots. If you don’t have a cable for every hole in the insert, install the
blank plugs to protect the control head from the weather.
Cable Collector Insert
Screws
1
2
3
4
5
Cable Collector Cover
Tab on Insert
3
Slot on Cover
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Plug Cable Connector Assembly to
Back of Control Head
10. While holding cables in place in
the cable collector insert, thread the
cables through the slot in the bottom
of the cable collector cover, line up
the cable collector insert and cover,
then slide the cover into place on the
insert.
Connecting the Control Head Power Cable to the Boat
A 6' (2 m) long power cable is included to supply power to the control head.
You may shorten or lengthen the cable using 18 gauge multi-stranded
copper wire.
CAUTION: Some boats have 24 or 36 Volt electric systems, but the control head
MUST be connected to a 12 VDC power supply.
NOTE: The tab on the Cable Collector
insert goes into the slot on the cover.
The control head power cable can be connected to the electrical system of
the boat at one of two places: a fuse panel usually located near the console,
or directly to the battery.
11. Attach the cable collector insert to the cable collector cover using
the 2 Phillips screws provided.
12. Place the control head back onto the mounting bracket. Plug in the
cable collector assembly to the back of the control head. Cable
connectors and cable sockets are keyed to prevent reverse
installation, so be careful not to force the connectors into the wrong
sockets. Once the cable collector and all cables are plugged into the
back of the control head, lock the assembly into place by threading
the knurled screw into the threaded insert on the back of the
housing. Adjust the control head to the desired viewing angle and
secure by tightening the gimbal knobs.
GROUND
NOTE: Make sure that the power cable is disconnected from the control head at
the beginning of this procedure.
NOTE: Humminbird® is not responsible for over-voltage or over-current failures.
The control head must have adequate protection through the proper selection
and installation of a 3 amp fuse.
NOTE: You may wish to dress the cabling with nylon wire ties in order to hold the
cables together and create a cleaner assembly.
The Humminbird® 900 Series™ control head is now ready for operation.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Transducer Installation
1a. If a fuse terminal is available, use crimp-on type electrical
connectors (not included) that match the terminal on the fuse
panel. Attach the black wire to ground (-), and the red wire to
positive (+) 12 VDC power. Install a 3 amp fuse (not included) for
protection of the unit. Humminbird® is not responsible for over-
voltage of over-current failures.
There are three different installation methods for your transducer:
• Transom Transducer
• Inside the Hull Transducer
• Trolling Motor Transducer.
Your 900 Series™ uses a Two Piece Kick-up transducer mounting bracket.
Find the section that describes the method of installation you will be using.
or...
1b. If you need to wire the control head directly to a battery, obtain
and install an inline fuse holder and a 3 amp fuse (not included)
for the protection of the unit. Humminbird® is not responsible for
overvoltage or over-current failures.
NOTE: If the included transducer will not work for your application, you may
exchange it, NEW and UNASSEMBLED, with mounting hardware included, for a
transducer appropriate for your application - often at very little or no charge
depending on the transducer. Call the Humminbird® Customer Resource Center
at 1-800-633-1468 for details and pricing, or visit www.humminbird.com.
NOTE: In order to minimize the potential for interference with other marine
electronics, a separate power source (such as a second battery) may be
necessary.
NOTE: Due to the wide variety of hulls, only general instructions are presented
in this installation guide. Each boat hull represents a unique set of requirements
that should be evaluated prior to installation. In addition to the hardware
supplied with your transducer, you will need a powered hand drill and various
drill bits, various hand tools, including a ruler or straightedge, a level, a 12" plumb
line (weighted string or monofilament line), marker or pencil, safety glasses and
dust mask, and marine-grade silicone sealant.
You are now ready to install the transducer. Find the section that refers to
your specific transducer installation method.
NOTE: Please read all instructions carefully and completely before beginning the
installation process.
NOTE: When drilling holes in fiberglass hulls, it is best to start with a smaller bit
and use progressively larger drill bits to reduce the chance of chipping or flaking
the outer coating.
NOTE: Your transducer may not look exactly like the transducer shown in the
illustrations, but it will mount in exactly the same way.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
On outboard or inboard/outboard boats, it is best to locate the
transducer at least 15" to the side of the propeller(s).
Transom Transducer Installation
If you will be installing a transom mounted transducer, use the procedures
in this section. There are several procedures you will have to perform in order
to install a transom-mounted transducer. They are:
Stepped Hull
Areas of Possible Turbulence
• Locate transducer mounting location
• Prepare the mounting location
• Assemble the transducer and perform initial mounting
• Route the transducer cable
• Connect the transducer cable
• Perform a final test of the transom transducer installation.
Rivets
Strakes
Step
Rib
Transom
Hull
1. Locating the transducer mounting location
NOTE: If transom mounting is not possible because of a stepped hull or
cavitation noise, and you have a single layer fiberglass hull, In-hull installation is
an option. See Inside the Hull Transducer Installation for more information.
• The best way to locate turbulence-free water is to view the transom
while the boat is moving. This method is recommended if maximum
high-speed operation is a high priority. If this is not possible, select a
location on the transom where the hull forward of this location is
smooth, flat and free of protrusions or ribs.
Turbulence: You must first determine the best location on the transom to
install the transducer. It is very important to locate the transducer in an area
that is relatively free of turbulent water. Consider the following to find the
best location with the least amount of turbulence:
Level
• As the boat moves through the water, turbulence is generated by the
weight of the boat and the thrust of the propeller(s) - either
clockwise or counter-clockwise. This turbulent water is normally
confined to areas immediately aft of ribs, strakes or rows of rivets on
the bottom of the boat, and in the immediate area of the propeller(s).
Clockwise propellers create more turbulence on the port side.
15”
Find a turbulence-free location at least 15" from the propeller(s)
and not in line with trailer bunks or rollers.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
• On boats with stepped hulls, it may be
possible to mount the transducer on the
step. Do not mount the transducer on
the transom behind a step to avoid
popping the transducer out of the water
at higher speeds; the transducer must
remain in the water for the control head
to maintain the sonar signal.
2. Preparing the Mounting Location
In this procedure, you will determine the mounting location and drill two
mounting holes, using the transducer mounting bracket as a guide.
1. Make sure that the boat is level on the trailer, both from port to
starboard and from bow to stern, by placing your level on the deck
of the boat, first in one direction, then in the other.
Deadrise Angle
2. Hold the mounting bracket against the transom of the boat in the
location you have selected (Figure 18). Align the bracket horizontally,
using the level; make sure that the lower corner of the bracket does
not protrude past the bottom of the hull, and there is at least 1/4"
clearance between the bottom of the bracket and the bottom of the
transom for fiberglass boats, and 1/8" clearance for aluminum boats.
• If the transom is behind the propeller(s), it may be impossible to find
an area clear from turbulence, and a different mounting technique or
transducer type should be considered, such as an Inside the Hull
Transducer (see Inside the Hull Transducer Installation).
• If you plan to trailer your boat, do not mount the transducer too close
to trailer bunks or rollers to avoid moving or damaging the transducer
during loading and unloading of the boat.
Positioning the
Boat Hull Types Require
Mounting Bracket
Different Mounting Positions
• If high speed operation is critical, you may want to consider using an
In-Hull transducer instead of this Transom Mount transducer.
Level
NOTE: The hydrodynamic shape of your transducer allows it to point straight
down without deadrise adjustment.
NOTE: If you cannot find a transom mount location that will work for your high-
speed application, find an In-Hull Transducer by contacting our Customer
Resource Center at either 1-800-633-1468 or by visiting our website at
www.humminbird.com.
1/4” for fiberglass
1/8” for aluminum
14
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: If you have a flat-bottomed aluminum boat, some additional adjustment
may be needed to accommodate the rivets on the bottom of the boat (i.e. the gap
may need to be a little smaller than 1/8"). This will help you to avoid excessive
turbulence at high speeds.
3. Assembling the Transducer and Initial Mounting
In this procedure, you will assemble the transducer using the hardware
provided, then mount it and make adjustments to its position without locking
it in place.
NOTE: If your propeller moves clockwise (in forward, as you're facing the stern of
the boat from behind), mount the transducer on the starboard side, and align the
bottom right corner of the mounting bracket with the bottom of the boat. If your
propeller moves counter-clockwise (in forward, as you're facing the stern of the
boat from behind), mount the transducer on the port side, and align the bottom
left corner of the mounting bracket with the bottom of the boat.
NOTE: You will initially assemble the transducer and the pivot arm by matching
the two ratchets to a numbered position on the transducer knuckle. Further
adjustments may be necessary.
1a. If you already know your transom angle, refer to the chart below for
the initial position to use to set the ratchets. If your transom is
angled at 14 degrees (a common transom angle for many boats) use
position 1 for the ratchets. In either case, go to step 2.
Using the Mounting Bracket
to Mark the Initial Drill Holes
3. Continue to hold the bracket on the transom
of the boat, and use a pencil or marker to
mark where to drill the two mounting holes.
Mark the drill holes near the top of each
slot, making sure that your mark is centered
in the slot.
Third Hole
or...
Bead Alignment
Number
1
4
2
5
3
1
4
2
5
3
1
Transom Angle (°)
-2 -1
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
0.0 cm
0“
1.1cm
1/2“
2.5 cm
1“
4.3 cm
1 5/8“
5.9 cm
2 3/8“
7.6 cm
3“
9.3cm
3 5/8“
11.1cm
4 3/8“
12.9cm
5“
14.9cm
5 7/8“
16.9cm
6 5/8“
NOTE: The third hole should not be drilled until the
angle and height of the transducer is finalized, which
you will not do until a later procedure.
Measured Distance (x)
Fourth Hole
Mark Initial
Drill Holes
1b. If you do not know your transom angle, measure it using a plumb line
(weighted nylon string or monofilament line) exactly 12 inches long.
Hold the top of the plumb line against the top of the transom with your
finger, and wait until the line hangs straight down. Using a ruler,
measure the distance from the bottom of the plumb line to the back of
the transom, then use the chart.
4. Make sure that the drill bit is perpendicular
to the actual surface of the transom, NOT
parallel to the ground, before you drill.
Using a 5/32” bit, drill the two holes only to
a depth of approximately 1”.
NOTE: On fiberglass hulls, it is best to use progressively larger drill bits to reduce
the chance of chipping or flaking the outer coating.
NOTE: It is important to take your measurement in the figure showing Measuring
the Transom Angle, from exactly 12 inches down from the top of the transom.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Place the two ratchets, one on either side of the transducer knuckle,
so that the beads on each ratchet line up with the desired position
number on the knuckle. If you are setting the ratchets at position 1,
the beads on each ratchet will line up with the rib on the transducer
knuckle to form one continuous line on the assembly.
Transducer Knuckle Positions
Knuckle
Ratchets Placed in Position 1
Beads
Ratchet
NOTE: The ratchets are keyed; make sure that the square teeth on each ratchet face
the square teeth on the transducer knuckle, and the triangular teeth face outward.
Rib at
position 1
Hold the ratchets on the transducer knuckle with one hand and fit
the pivot arm over them until it snaps into place with the other
hand. Refer to the illustration.
Ratchets Placed in Position 2
Fitting the Pivot Arm Over the Ratchet
Measuring the Transom Angle
Bead
Plumb
line
Ratchet
Rib
12”
Transom
Angle in
degrees
(°)
Measured
Weight
Distance (X)
16
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Align the mounting bracket transducer assembly with the drilled
holes in the transom. With a 5/16" socket driver, mount the
assembly to the transom using the two #10 - 1" long screws
provided.
Inserting the Pivot Arm Assembly
Into the Mounting Bracket
Inserting the Pivot Bolt
Mounting the Assembly to the Transom
3. Put the pivot bolt through the assembly to hold it in position and
loosely install the nut, but do NOT tighten the nut at this time. Insert
the pivot arm assembly into the mounting bracket. Do NOT snap the
assembly closed, as you will need to access the mounting bracket in
the next step.
NOTE: Make sure that the mounting screws are snug, but do not fully tighten the
mounting screws at this time to allow the transducer assembly to slide for
adjustment purposes.
NOTE: If the pivot assembly is snapped closed over the mounting bracket, use a
flat head screwdriver or similar tool to gently pry the assembly away from the
mounting bracket).
5. Snap the pivot arm down into place.
6. Adjust the initial angle of the transducer from back to front by
rotating the transducer until the side seam on the transducer is
almost parallel with the bottom of the boat, one click at a time in
either direction.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Continue to adjust until the bracket is also level from port to
starboard (horizontally level as you look at the transducer from
behind the boat.
Adjusting the Initial Transducer Angle
One click too high
Correctly aligned
(transducer side seam
aligned with boat bottom)
9. Mark the correct position on the transom by tracing the silhouette
of the transducer mounting bracket with a pencil or marker.
Trailing edge
10. Tighten the pivot bolt, using the pivot screw and nut to lock the
Leading edge
One click too low
assembly. Hand tighten only!
11. Snap open the assembly and hand-tighten the two mounting
screws, then snap the assembly closed.
7. Adjust the transducer assembly vertically, until the seam on the
leading edge of the transducer (the edge closest to the transom of
the boat) is level and just slightly below the hull.
NOTE: You will drill the third mounting hole and finalize the installation after you
route the cable and test and finish the installation in the following procedures.
Adjusting the Transducer
Mounting Position
Leveling the Mounting
Assembly Horizontally
4. Routing the Cable
Level
The transducer cable has a low profile connector, which must be routed to
the point where the control head is mounted. There are several ways to route
the transducer cable to the area where the control head is installed. The
most common procedure routes the cable through the transom into the boat.
NOTE: Your boat may have a pre-existing wiring channel or conduit that you can
use for the transducer cable.
Seam aligned with boat hull
1. Unplug the other end of the transducer cable from the control head.
Make sure that the cable is long enough to accommodate the
planned route by running the cable over the transom.
NOTE: The transducer has a natural downward slant of 4-5 degrees from leading
edge (closest to the boat transom) to trailing edge (farthest away from the boat).
Looking at the back of the transducer, the seam should be slightly below the
bottom of the hull.
CAUTION! Do not cut or shorten the transducer cable, and try not to damage the
cable insulation. Route the cable as far as possible from any VHF radio antenna
cables or tachometer cables to reduce the possibility of interference. If the cable
18
Download from Www.Somanuals.com. All Manuals Search And Download.
is too short, extension cables are available to extend the transducer cable up
to a total of 50'. For assistance, contact the Customer Resource Center at
www.humminbird.com or call 1-800-633-1468 for more information.
4. Route and secure the cable by attaching
the cable clamp to the transom; drill one
9/64" diameter x 5/8" deep hole, then fill
hole with marine-grade silicone sealant,
then attach the cable clamp using a #8 x
5/8" screw.
Storing Excess Cable
NOTE: The transducer can pivot up to 90 degrees in the bracket. Allow enough
slack in the cable for this movement. It is best to route the cable to the side of
the transducer so the transducer will not damage the cable during movement.
2a. If you are routing the cable over the transom of the boat, secure the
cable by attaching the cable clamp to the transom, drilling 9/64"
diameter holes for #8 x 5/8" wood screws, then skip directly to
procedure 5, Connecting the Cable.
NOTE: If there is excess cable that needs to be gathered at one location (as
shown in the illustration), dress the cable routed from both directions so that a
single loop is left extending from the storage location. Doubling the cable up from
this point, form the cable into a coil. Storing excess cable using this method can
reduce electronic interference.
or...
Routing the Cable
2b. If you will be routing the cable through a
hole in the transom, drill a 5/8"
diameter hole above the waterline.
Route the cable through this hole, then
fill the hole with marine-grade silicone
sealant and proceed to the next step
immediately.
5. Connecting the Cable
Insert the transducer cable into the appropriate terminal slot. The cable
connectors are labeled, and there are corresponding labels on the cable
holder on the rear of the control head. The slots are keyed to prevent
reversed installation, so be careful not to force the connector into the holder.
Refer to your manual and/or control head installation guide for the correct
procedure for installing the cable connectors to the control head.
3. Place the escutcheon plate over the
cable hole and use it as a guide to mark
the two escutcheon plate mounting
holes. Remove the plate, drill two 9/64"
diameter x 5/8" deep holes, and then fill
both holes with marine-grade silicone
sealant. Place the escutcheon plate over
the cable hole and attach with two
#8 x 5/8" wood screws.
1. Plug the other end of the transducer cable back into the control
head connection holder.
Your control head is now ready for operation.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: The deeper the transducer is in the water, the more likely that a rooster
tail of spray will be generated at high speeds, so make sure that the transducer
is as high as it can be and still be submerged in the water.
6. Test and Finish the Installation
Once you have installed both the control head and the transom transducer, and
have routed all the cables, you must perform a final test before locking the
transducer in place. Testing should be performed with the boat in the water,
although you can initially confirm basic operation with the boat out of the water.
If you are still not getting good high speed readings, you may need
to disassemble the transducer mounting assembly and re-position
the ratchets.
1. Press POWER once to turn the control head on. If the unit does not
power up, make sure that the connector holder is fully seated in the
receptacle and that power is available.
If you do change the transducer position, re-trace the position of the
mounting bracket before proceeding.
2. If all connections are correct and power is available, the
Humminbird® control head will enter Normal operation.
NOTE: It is often necessary to make several incremental transducer adjustments
before optimum high speed performance is achieved. Due to the wide variety of boat
hulls, however, it is not always possible to obtain high speed depth readings.
3. If the bottom is visible on-screen with a digital depth readout, the unit
is working properly. Make sure that the boat is in water greater than 2'
but less than the depth capability of the unit, and that the transducer
is fully submerged, since the sonar signal cannot pass through air.
6. Once you have reached a consistently good sonar signal at the
desired speeds, you are ready to lock down the transducer settings.
Force the pivot to the Up position to gain access to the mounting
screws, then re-align the mounting bracket against the transom of
the boat to match the traced silhouette. Check the bracket position
with the level again to make sure it is still level, then mark the third
mounting hole using a pencil or marker. Unscrew and remove the
mounting screws and the transducer assembly and set aside.
NOTE: The transducer must be submerged in water for reliable transducer
detection.
4. If the unit is working properly, gradually increase the boat speed to
test high-speed performance. If the unit functions well at low
speeds, but begins to skip or miss the bottom at higher speeds, the
transducer requires adjustment.
7. Drill the third mounting hole, using a 5/32” drill bit. Use a marine-
grade silicone sealant to fill all three drilled mounting holes,
especially if the holes penetrated the transom wall.
5. If you have the correct angle set on the transducer, yet lose a bottom
reading at high speed, adjust the height and the running angle in
small increments to give you the ideal transducer position for your
boat. First, adjust the height in small increment.
NOTE: On fiberglass hulls, it is best to use progressively larger drill bits to reduce
the chance of chipping or flaking the outer coating.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Fully Tighten All Three
Mounting Screws
8. Re-position the transducer assembly against
the transom of the boat, then hand-install
all three screws. Make sure that the
transducer location and the pivot angle
have not changed, then fully tighten all
three mounting screws. Snap the pivot
back down. If you have performed the
preceding procedures correctly, the
transducer should be level and at the
right height for optimal operation.
Inside the Hull Transducer Installation
If you choose to mount your transducer inside the hull of your boat, perform the
procedures in this section. In-hull mounting generally produces good results in
single thickness fiberglass-hulled boats. Humminbird® cannot guarantee depth
performance when transmitting and receiving through the hull of the boat,
since some signal loss occurs. The amount of loss depends on hull construction
and thickness, as well as the installation position and process.
This installation requires slow-cure two-part epoxy. Do not use silicone or
any other soft adhesive to install the transducer, as this material reduces the
sensitivity of the unit. Do not use five-minute epoxy, as it has a tendency to
cure before all the air bubbles can be purged, thus reducing signal strength.
NOTE: In-hull mounting requires an installed and operational control head.
NOTE: The integral temperature probe will not work with in-hull mounting, so you
may either want to consider purchasing a Temperature/Speed accessory, a Temp
Sensor, or obtaining a different transducer. Humminbird® offers a transducer
exchange program to swap the NEW and UNASSEMBLED transducer, accompanied
by mounting hardware, for one without an integral temperature probe. Call the
Humminbird® Customer Resource Center at 1-800-633-1468 for details, or visit
www.humminbird.com for more information.
NOTE: Your transducer may not look exactly like the transducer shown in the
illustrations, but it will mount in exactly the same way.
• Locate transducer mounting location
• Perform a trial installation
• Route the transducer cable
• Permanently mount the transducer.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Determine the transducer mounting location
2. Trial installation
Decide where to install the transducer on the inside of the hull. Consider the
following to find the best location:
You will not be able to adjust the mounting after an inside the hull
transducer is installed. It is best, therefore, to perform a trial installation first
that includes running the boat at various speeds, in order to determine the
best mounting area before permanently mounting the transducer.
• Observe the outside of the boat hull to find the areas that are mostly
free from turbulent water. Avoid ribs, strakes and other protrusions,
as these create turbulence.
1. Plug the transducer into the control head, then power up the control
head. When the control head detects a functioning transducer, it
will automatically enter Normal operating mode.
Stepped Hull
Areas of Possible Turbulence
2. View the sonar signal at its best by holding the transducer over the
side, immersed in the water, so that it is pointing straight down over a
known flat bottom. Use the display to benchmark against the sonar
signal that will be detected once the transducer is placed in the hull.
3. Place the transducer body face down at the identified mounting
location inside the hull, with the end that has the mounting ears
pointed towards the bow of the boat.
Rivets
Strakes
Step
Rib
Preferred Mounting Area
Transom
Hull
• As a general rule, the faster the boat can travel, the further aft and
closer to the centerline of the hull the transducer has to be located
in order to remain in contact with the water at high speeds.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Fill the hull with enough water to submerge the transducer body.
Use a sand-filled bag or other heavy object to hold the transducer in
position. The transducer cannot transmit through air, and the water
purges any air from between the transducer and the hull, and fills
any voids in the coarse fiberglass surface.
4. Permanently mount the transducer
1. Make sure the position of the transducer is marked.
2. You may have to disconnect the cable to the control head and
reconnect it at the end of this procedure.
3. Remove the water from inside the hull and thoroughly dry the
mounting surface. If the surface is excessively rough, it may be
necessary to sand the area to create a smooth mounting surface.
5. View the sonar signal on the display and compare against what you
observed in Step 2, making sure that the boat is in the same location
as it was during your observations in Step 2. If the results are
comparable, move on to Step 6. Otherwise, locate a new position in
the hull and repeat Steps 3 through 5.
4. Slowly and thoroughly mix an ample quantity of two-part slow cure
epoxy. Avoid trapping air bubbles.
6. Run the boat at various speeds and water depths while observing
the screen on the control head. If depth performance is required,
test the transducer in water at the desired depth. If the performance
is acceptable, move on to Step 7. If the performance is not
acceptable, repeat Steps 3 through 6.
7. Once you have determined the best mounting location using the
above steps, mark the position of the transducer.
3. Route the cable
1. Once the mounting location is determined and you have marked the
position of the transducer, route the cable from the transducer to
the control head.
5. Coat the face of the transducer and the inside of the hull with epoxy.
6. Press the transducer into place with a slight twisting motion to
purge any trapped air from underneath, keeping the end of the
transducer that has the mounting ears pointed forward, towards the
bow of the boat.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: Proper operation requires the end of the transducer that has the mounting
ears to face towards the bow of the boat.
Trolling Motor Transducer Installation
If you want to install the transducer on a trolling
motor, use this procedure. Several styles of the
transducer are compatible with trolling motor
mounting. If you have a trolling motor bracket,
refer to the separate installation instructions that
are included with the bracket.
7. Weight the transducer so that it will not move while the epoxy is
curing.
NOTE: When the epoxy cures, no water is necessary inside the hull.
8. If you unplugged the transducer cable at the beginning of this
procedure, plug it back into the control head.
NOTE: After trolling motor transducer installation, please perform the final
testing and then finalize the installation (see Test and Finish the Transducer
Installation).
NOTE: Neither water, spilled gasoline, nor oil will affect the performance of the
transducer.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Trolling Motor Transducer Options
GPS Receiver Installation
If you don’t have a trolling motor transducer, there are several options:
To optimize performance of the GPS receiver, mount it in an area that has full
exposure to the sky. The effective area of reception is 10° above the horizon.
Different circumstances determine the mounting method appropriate for
your GPS receiver.
• You may purchase a Trolling Motor Adapter kit that will allow you to
mount the transducer on the trolling motor.
• You may also exchange your NEW and UNASSEMBLED transducer
(with mounting hardware included) for a trolling motor transducer.
If you have…
Then use:
There are also several transducer switches available that support the
following configurations:
An existing antenna stem with
standard 1" – 14 thread stem
Stem Mount with Existing
1” - 14 Thread Stem
• Two control heads with one transducer
• Two transducers with one control head.
Access for cable routing under
the mounting location
Access Under Mounting
Location
NOTE: Call the Humminbird® Customer Resource Center at 1-800-633-1468 for
details and pricing, or visit www.humminbird.com for more information.
No access under the mounting
location
No Access Under Mounting
Location
The pinouts of the pigtail cable are as follows:
• Red Wire, +12V (output voltage only)
• Black Wire, Ground
• White Wire, NMEA Out.
CAUTION! Please use caution before connecting the red +12V wire to any other
NMEA device. This is an output voltage provided by the Fishfinder unit and
GPS receiver and should only be connected to those NMEA devices that need a
12 volt input.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Use electrical tape to secure the NMEA pigtail to the cable as
shown.
Stem Mounting with an Existing 1" - 14 Thread Stem
Follow these steps to stem mount the GPS receiver:
NOTE: Leave the NMEA pigtail secured to the cable unless needed. This will
make removing the receiver easier.
NOTE: If you have an existing stem for mounting the GPS receiver, proceed
directly to step 2 of the following procedure.
4. Route the GPS receiver cable through the stem and continue with
the planned route you chose in step 1.
1. Determine the best location to mount your GPS receiver. Preplan
and test the cable routing to your control head before any drilling or
cutting of your boat surfaces. If you have purchased hardware to
stem mount your GPS receiver, follow the instructions included with
that hardware to mount the stem (antenna pole).
5. Attach the GPS receiver to its base using the included #6 - 7/8"
screws.
NOTE: AS-EC10 10' extension cables are available from Humminbird® if your
planned routing exceeds 20', (6 m). Maximum cable length, including extensions,
should not exceed 50' (16 m).
3
NOTE: Remember to caulk or seal screw holes and drilled holes as needed to
protect your boat from water damage.
2. Screw on the receiver base to the stem
first, making sure that the stem pipe does
1
1
2
not protrude from the receiver base. This
adds protection to the cable when pulling it
through the pipe stem. In addition to this,
de-burr the pipe edges to reduce cable
abrasion.
2
4
3
Receiver
1
2
3
Receiver Base
Stem Pipe
Mounting Screws
Cable Route
3
4
NMEA Pigtail Taped
1
2
NMEA Pigtail Cable Out
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Access Under Mounting Location
No Access Under Mounting Location
Access Under Mounting Location
Follow these steps to deck mount the GPS receiver when routing the cable
down through the mounting location:
1. Determine the best location, then test route the 20' (6 m) cable from
the mounting location to the control head.
NOTE: Installation details may vary with unit configuration.
2. Mark the mounting location and drill a 3/4" (19 mm) hole for the
cable and cable plug. Route the cable.
No Access Under Mounting Location
3. Cover the cable hole with the receiver. Make sure the receiver is
flush on the surface and mark the two mounting holes with a pencil
or punch.
Follow these steps to deck mount the GPS receiver in a situation where you
must route the cable to the side because there is no space for a cable
underneath the mounting location.
4. Move the receiver to the side and drill two pilot holes using a 9/64"
(3.5 mm) bit.
1. Determine the best location, then test route the cable from the
mounting location to the control head.
NOTE: Remember to caulk or seal screw holes and drilled holes as needed to
NOTE: AS-EC10 10' extension cables are available from Humminbird® if your
planned routing exceeds 20', (6 m). Maximum cable length, including extensions,
should not exceed 50' (16 m).
protect your boat from water damage.
5. Align the GPS receiver screw holes over the pilot screw holes and
attach with the #8 - 1 1/4" Phillips head screws. Hand tighten only!
2. Confirm the cable length is good and route the cable from the
receiver to the control head. If holes are required to route the cable,
they must be 3/4" (19 mm) to allow for the cable connector. Secure
the NMEA pigtail with electrical tape.
NOTE: If the mounting surface is thin and made of a lighter material, a backing
material may be needed below the mounting surface.
NOTE: Remember to caulk or seal screw holes and drilled holes as needed to
protect your boat from water damage.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
3. The GPS receiver has two wire routing notches. Use the cable notch
closest to the intended cable route.
Finish Routing the Cable and
Check GPS Receiver Operation
After installing a GPS receiver, you should perform the following procedure
to finish routing the GPS cable to the control head and to check to make sure
that the control head is working correctly.
4. With the cable routed, position the GPS receiver in the planned
mounting location and mark the mounting holes with a pencil or
punch.
1. Secure the cable along its path to the control head as needed with
cable ties.
5. Move the GPS receiver to the side and drill the two 9/64" (3.5 mm)
pilot holes.
2. Plug the GPS receiver cable into the Communications port on the
control head. See Testing the System Installation to use the
System Status start-up option and/or the GPS Diagnostic View to
confirm a good installation.
6. Align the GPS receiver's screw holes over the pilot screw holes and
attach with the #8 - 1 1/4" Phillips head screws. Hand tighten only!
1
2
3
4
Power
1
2
3
4
5
Temp/Speed
Communications
Transducer
5
Cable Collector Insert
28
Download from Www.Somanuals.com. All Manuals Search And Download.
3. From the System Status screen, view accessory connections by
pressing the VIEW key. See System Status for more information
about the Accessory Test.
Testing the System Installation
After you have completed the installation of the control head, transducer,
and any other accessories such as the GPS receiver, and have made all the
cabling connections required, you must test the installation before using the
system. Thorough testing should be performed with the boat in the water;
however, you can confirm basic operation initially with the boat out of the
water as well.
NOTE: The speed will be detected only if the paddlewheel has moved since the
900 Series™ has been powered up.
4. From the System Status screen, see a GPS Diagnostic View by
pressing the View key. GPS Diagnostic View shows a sky chart and
numerical data from the GPS receiver. The sky chart shows the
location of each visible GPS satellite with its satellite number and a
signal strength bar. A dark grey bar indicates that the satellite is
being used to determine your current position. A light gray bar
indicates that the satellite is being monitored, but is not yet being
used. See System Status for more information about the GPS
Diagnostic View.
To test the installation:
1. Press the POWER/LIGHT key on the control head once to turn on the
control head. (There will be an audible chirp to let you know that you
pressed the key, and the initial Title screen will appear.) If the unit
does not power up, make sure that power is available. While the
Title screen is shown on the display, press the MENU key to display
the Start-Up Options menu. Use the UP or DOWN 4-WAY Cursor
keys to position the cursor, then the RIGHT Cursor key to select
System Status from the Start-Up Options menu (see the Start-Up
Options Menu section for more information about these menu
choices). The System Status Self Test screen will appear.
NOTE: If you wait too long, the system will default to whichever menu mode
happens to be highlighted, and you will have to start again.
2. Self Test displays results from the internal diagnostic self test,
including unit serial number, Printed Circuit Board (PCB) serial
number, software revision, total hours of operation and the input
voltage. See System Status for more information about the Self Test.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started - Using Your 900 Series™
Powering Up the Control Head
Your 900 Series™ Fishing System user interface is easy to use. A
combination of keys, different views, and situation-specific, customizable
menus allows you to control what you see on the color display. Refer to the
following illustration, and see Key Functions, Views, and The Menu
System) for more information.
Turn on your 900 Series™ control head by pressing the POWER key. The Title
screen is displayed until the 900 Series™ begins operation. Your 900 Series™
will begin Normal or Simulator operation, depending on the presence or
absence of a transducer.
3
9
7
5
8
6
1
10
12
11
4
2
900 Series™ 957c Combo Title Screen
Screen
4-WAY Cursor Control Key
MENU Key
1
2
3
4
5
6
7
8
MMC/SD Card Slot
ZOOM (+/-) Keys
POWER/LIGHT Key
INFO Key
VIEW Key
9
EXIT Key
10
11
12
View Preset Keys
GOTO Key
MARK Key
30
Download from Www.Somanuals.com. All Manuals Search And Download.
What’s On the Sonar Display
The 900 Series™ can display a variety of useful information about the area under and adjacent to your boat, including the following items:
Speed - if a Speed accessory or GPS Receiver
7
1
is attached, the 900 Series™ can display the
speed of the boat, and can keep a triplog of
nautical or statute miles traveled.
10
Thermoclines - layers of water with different
temperatures that appear at different depths
and different times of the year. A thermocline
typically appears as a continuous band of
many colors moving across the display at the
same depth.
8
2
3
4
8
9
Sonar Color Bar - color spectrum indicating
low to high sonar intensity returns, where
red indicates high intensity and white
indicates low intensity.
9
5
6
7
Bait Ball
10
11
12
11
RTS® (Real Time Sonar) Window
Second Sonar Return - when the sonar
signal bounces between the bottom and the
surface of the water and back again. Use
the appearance of the second return to
determine bottom hardness. Hard bottoms
will show a strong second return, while soft
bottoms will show a very weak one or none
at all.
12
Depth - water depth; can be set to alarm when the water becomes too shallow.
Timer - Elapsed time with Speed accessory or GPS Receiver.
1
2
3
4
Barometric Pressure - Requires optional-purchase WeatherSense®
Temperature - water surface temperature
5
6
Distance - Distance traveled with Speed accessory or GPS Receiver.
Average Speed - Average speed reading with Speed accessory or GPS Receiver.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Understanding Sonar History
Bottom Presentation
It is important to understand the significance of the 900 Series™ display. The
display does NOT show a literal 3-dimensional representation of what is
under the water. Each vertical band of data received by the control head and
plotted on the display represents something that was detected by a sonar
return at a particular time. As both the boat and the targets (fish) may be
moving, the returns are only showing a particular segment of time when
objects were detected, not exactly where those objects are in relation to
other objects shown on the display.
As the boat moves, the unit charts the changes in depth on the display to
create a profile of the Bottom Contour. The type of bottom can be
determined from the return charted on the display. A Hard Bottom such as
compacted sediment or flat rock appears as a thinner line across the display.
A Soft Bottom such as mud or sand appears as a thicker line across the
display. Rocky Bottoms have a broken, random appearance.
NOTE: A sloping bottom will be represented as a thicker line across the display.
Harder bottoms typically will be displayed with red and softer bottoms typically
will be displayed with blue.
Real Time Sonar (RTS®) Window
The sonar returns from the bottom, structure and fish can be represented as
either Structure ID® or WhiteLine®. See Sonar Menu: Bottom View for
details on how to set the bottom view.
A Real Time Sonar (RTS®) Window appears on the right side of the display in
the Sonar View only. The RTS® Window always updates at the fastest rate
possible for depth conditions and shows only the returns from the bottom,
structure and fish that are within the transducer beam. The RTS® Window plots
the depth and intensity of a sonar return. (See Sonar Menu: RTS® Window).
Structure ID® represents weak returns in blue and strong returns in red.
The Narrow RTS® Window
indicates the sonar intensity
through the use of colors.
Red indicates a strong return
and blue indicates a weak
return. The depth of the
sonar return is indicated by
the vertical placement of the
return on the display depth
scale.
The Wide RTS® Window
indicates the sonar intensity
through the use of a bar
graph. The length of the
plotted return provides an
indication of whether the
return is weak or strong. The
depth of the sonar return is
indicated by the vertical
placement of the return on
the display depth scale.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
WhiteLine® highlights the strongest sonar returns in white, resulting in a
distinctive outline. This has the benefit of clearly defining the bottom on
the display.
Key Functions
Your 900 Series™ user interface consists of a set of easy-to-use keys that
work with various on-screen views and menus to give you flexibility and
control over your fishing experience. Your control head has the following
keys:
• POWER/LIGHT key
• EXIT key
• VIEW key
• 4-WAY Cursor Control key
• MENU key
• VIEW PRESET keys.
• MARK key
• GOTO key
• INFO key
• ZOOM (+/-) keys.
POWER/LIGHT Key
The POWER/LIGHT key is used to turn the 900 Series™ on and
off, and also to adjust the backlight and background color of
the display. Press the POWER/LIGHT key to turn the unit on.
The Title screen is then displayed until the 900 Series™ begins
sonar operation.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
To adjust the backlight or to adjust the
display background color, press the
POWER/LIGHT key to access the Light and
Background menu. Use the 4-WAY Cursor
key to select Light or Background and then
use the LEFT or RIGHT Cursor key to change
the settings. Press EXIT to exit the Light and
Background menu.
MENU Key
The MENU key is used to access the menu system.
Start-Up Options Menu - Press the MENU key during the power up
sequence to view the Start-Up Options menu.
X-Press™ Menu - Press the MENU key once for the X-Press™ Menu. The X-
Press™ Menu allows you to access frequently-used settings without having
to navigate through the whole menu system. When the X-Press™ Menu is
displayed, you can use the UP or DOWN Cursor keys to move to a particular
menu choice. As soon as you alter a parameter (using the RIGHT or LEFT
Cursor keys) the X-Press™ Menu will collapse temporarily, and the screen
will update if it is affected by your menu setting change, allowing you to see
the effects of your action immediately. Reactivate the X-Press™ Menu by
using the UP or DOWN Cursor keys.
Press and hold the POWER/LIGHT key for 3 seconds to turn the unit off. A
message will appear telling you how many seconds there are until shutdown
occurs. Your 900 Series™ should always be turned off using the
POWER/LIGHT key. This will ensure that shutdown occurs properly and any
menu settings will be saved.
VIEW Key
The VIEW key is used to cycle through all available views.
Press the VIEW key to advance to the next view. Repeatedly
pressing VIEW cycles through all views available. Views can be hidden to
optimize the system to your fishing requirements (see View Menu Tab).
Main Menu - Press the MENU key twice for the tabbed Main Menu System.
The Main Menu System is organized under tabbed headings to help you find
a specific menu item quickly: Alarms, Sonar, Navigation, Chart, Setup,
Views, and Accessories tabs are part of your tabbed Main Menu System.
Use the LEFT or RIGHT 4-WAY Cursor Control key to select a tab; then use
the DOWN or UP key to select the menu item, and the LEFT or RIGHT key to
alter a menu setting.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
4-WAY Cursor Control Key
VIEW PRESET keys
The 4-WAY Cursor Control Key has multiple functions,
depending on the situation:
The VIEW PRESET keys are used to program your three favorite
views for quick retrieval. Instead of using the VIEW key to
cycle through every view to find the one you want, you can program the
VIEW PRESET keys to display a specific view immediately. To program each
VIEW PRESET key, use the VIEW key to cycle to the view you want to store.
Press and hold one of the VIEW PRESET keys for several seconds. A series of
audible chirps will be heard indicating that the view has been programmed
to the key. You can store up to three views, one on each key.
Freeze Frame - Pressing any arrow on the 4-WAY Cursor Control key will
freeze the display in the Sonar View and a cursor and cursor dialog box will
be displayed. The cursor can be positioned on the Sonar View using the 4-
WAY Cursor Control key.
Active Cursor - In any Bird's Eye View, the 4-WAY Cursor Control key controls the
motion of the eyepoint. In any Chart View, the 4-WAY Cursor Control key pans the
charts.
EXIT Key
The EXIT key has multiple functions, depending on the
situation:
NOTE: In either Freeze Frame or Active Cursor mode, you can also make the
cursor move diagonally by pressing in between two of the arrows on the 4-WAY
Cursor Control key..
• If an alarm is sounding, pressing EXIT will cancel the alarm.
Menu Selection - Use the DOWN or UP arrow keys to select a menu choice
from the menu list, then use the LEFT or RIGHT arrow keys to change a menu
setting.
• If a menu tab is selected, pressing EXIT will exit the menu mode and
return to the view.
• If a menu is active, pressing EXIT will return to the previous level in
the menu system.
Snapshot and Recording View - In the Snapshot and Recording View,
highlighting a recording icon and pressing the Right 4-WAY Cursor Control
key starts recording playback, and the Right and Left keys are used to control
the speed of playback.
• Pressing EXIT will cycle through the available views in reverse order.
• If Freeze Frame is active, pressing EXIT will return to a scrolling
display.
NOTE: Menu choices are implemented and saved immediately - no further action
is required.
• If the Cursor is active, pressing EXIT will remove the cursor from the
display.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Navigation is not affected by the Screen Snapshot feature. Also, if Screen
Snapshot is enabled but there is no GPS receiver connected, pressing the
MARK key will capture the screen image and display an error saying that a
GPS position fix is required to create a waypoint.
INFO Key
Press the INFO key while in any navigation view to display
information about objects that are nearest to an active cursor.
If the cursor is not active, the following menu will
be displayed. Use the 4-WAY Cursor Control key to
select Nearest Port, Nearest Tide Station or Nearest
Current Station, then use the RIGHT Cursor key to
display the requested information.
GOTO Key
The GOTO Key has multiple functions, depending on the
situation:
• If the Cursor is active, pressing the GOTO key while in any view
creates a waypoint and starts navigation towards that waypoint. If
the Cursor is not active, pressing the GOTO key displays the list of
waypoints, so that you can select the waypoint towards which you
want to navigate.
NOTE: The built-in UniMap™ does not contain Port, Tide or Current information.
This information is only available from optional purchase MMC/SD cards.
MARK Key
Press the MARK key while in any view to mark the position
of a waypoint, either at the current boat location, or, if the
Cursor is active, at the current Cursor location.
• If the GOTO key is pressed and held for more than 1.5 seconds, the
Man Overboard (MOB) function is activated. When MOB is activated,
an MOB waypoint, which is a permanent, sharable waypoint with a
large, distinctive icon, is created at the boat's current position
(regardless of whether the chart cursor is active or not). Any current
navigation will be cancelled and the current route discarded without
user notification, and MOB navigation begins immediately. The view
is switched to the Chart View automatically when MOB is activated,
and it is not possible to activate MOB or modify the current route
without first canceling MOB navigation. Any press of the GOTO key,
or selection of a GOTO menu item, will cause an error beep and a
short message will be displayed to the user that will disappear after
2 seconds.
The MARK key only functions if you have the GPS receiver connected, or if
you have enabled Screen Snapshot from the Accessories menu tab. If you
have enabled the Screen Snapshot feature, pressing the MARK key still
creates a waypoint, but it also captures the screen image to the optional-
purchase MMC/SD card.
NOTE: You must have an optional-purchase MMC/SD card installed for the
screen snapshot feature to work.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
• Sonar View
• Bird’s Eye View
ZOOM (+/-) Keys
Press the - or + ZOOM keys while in any of the Navigation
Views or the Sonar Zoom View to change the scale of the view
to appear closer or farther away.
• Sonar Zoom View
• Split Sonar View
• Chart/Bird’s Eye Combo View
• Chart/Chart Combo View
• Snapshot and Recording View • Chart View
• Self Test View
• Chart/Sonar Combo View
• Side Beam View.
• Accessory Test View
• GPS Diagnostic View
Views
Sonar View is the default view. When the VIEW key is pressed, the display
cycles through the available views. When the EXIT key is pressed, the display
cycles through the available views in reverse order. Any view can be hidden
or displayed as part of the view rotation using the Views Menu tab.
The views available on your 900 Series™ are:
Sonar
View
Side Beam
Sonar Zoom
View
View
NOTE: When you change any menu settings that affect the sonar, the view will update
immediately (i.e. you don’t have to exit the menu to apply the change to the screen).
Chart//Sonar
Combo View
Split Sonar
View
Chart View
Views and Readouts
Snapshhot and
Recording View
Chart//Chart
Combo View
All views have an Information Bar on the left side of the screen, consisting
of readouts that are stacked vertically, and that change from view to view.
You can customize the information displayed in individual readouts on many
views, including suppressing a particular readout so that nothing is
displayed; the ability to customize readouts depends on the view and
whether you are navigating (see Setup Menu Tab, Select Readouts for
more information).
Self Tesst View
Chart/Biird’s Eye
Combo View
Accessory
Test View
GPS Diagnnostic
View
Bird’s Eye
View
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Sonar View
Sonar View
6
8
9
7
Sonar View presents a historical log of sonar returns. The most recent sonar
returns are charted on the right side of the window; as new information is
received, the older information is moved across the display to the left. A
scale with Upper and Lower Depth Range readouts appears along the right
edge of the Sonar View. The scale indicates the distance from the surface of
the water to a depth range sufficient to show the bottom. Depth Range is
automatically selected to keep the bottom visible on the display, although
you can adjust it manually as well (see Sonar X-Press™ Menu).
1
2
10
5
11
3
4
Freeze Frame - Pressing any arrow on the 4-WAY Cursor Control key will
freeze the screen in the Sonar View and a cursor and cursor dialog box will
be displayed on the screen. The cursor can be positioned on the display
using the 4-WAY Cursor Control key to determine the depth of any sonar
return. The RTS® Window continues to update in Freeze Frame. In addition,
see the effects of menu setting changes with Instant Image Update.
12
Depth
Depth below Cursor
Distance to Cursor
Bearing to Cursor
RTS® Window
1
7
8
Triplog
2
3
4
5
6
Temperature
Speed
9
10
11
12
Pressing EXIT will exit Freeze Frame and the display will start to scroll.
Cursor
Sonar Color Bar
Depth of Cursor
Lower Depth Range
NOTE: If the Depth number is flashing, it means that the unit is having trouble
locating the bottom. This usually happens if the water is too deep, the transducer
is out of the water, the boat is moving too fast, or for any other reason that the
unit can’t accurately receive continuous data.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Sonar Zoom View
Sonar Zoom View
8
6
7
Sonar Zoom View increases the displayed resolution to separate sonar
returns that are very close together, such as those caused by fish suspended
close to the bottom or within structure. In Zoom View, the display is split to
show a narrow slice of the full range view on the right and the zoomed view
on the left. The full range view on the right also contains the Zoom Preview
Box that shows what part of the full range view is shown in zoom view on
the left; the Zoom Preview Box tracks the bottom in the full range view.
1
2
5
9
3
4
As the depth changes, the zoomed view updates automatically to display a
magnified image of the bottom. The Zoom Preview Box shows where the
zoomed view is in relation to the full range view. The Zoom Level, or
magnification, is displayed in the upper left corner and can be changed to
suit conditions. Upper and Lower Zoom Depth Range numbers indicate the
depth of the water which is being viewed.
10
12
11
Depth
Upper Depth Range, Full Range View
Upper Depth Range, Zoom View
Zoom Preview Box
1
7
8
Triplog
2
3
4
5
6
Temperature
Speed
9
Freeze Frame - Pressing any arrow on the 4-WAY Cursor Control key will
freeze the screen in the Sonar Zoom View and a cursor and cursor dialog box
will be displayed on the screen. The cursor can be positioned on the display
using the 4-WAY Cursor Control key to determine the depth of any sonar
return. In addition, see the effects of menu setting changes with Instant
Image Update.
Full Range View
10
11
12
Zoomed View
Zoom Level
Lower Depth Range, Full Range View
Lower Depth Range, Zoom View
Pressing EXIT will exit Freeze Frame and the display will start to scroll.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Split Sonar View
Split Sonar View
3
Split Sonar View displays sonar returns from the 83 kHz wide beam on the
left side of the screen and displays sonar returns from the 200 kHz narrow
beam on the right side of the screen. You can use the Split Sonar View to
make side by side comparisons between the sonar returns from the 83 kHz
wide beam and the 200 kHz narrow beam.
1
2
Freeze Frame - Pressing any arrow on the 4-WAY Cursor Control key will freeze
the screen in this view and a cursor and cursor dialog box will be displayed on
the screen. The cursor can be positioned on the display using the 4-WAY Cursor
Control key to determine the depth of any sonar return. In addition, see the
effects of menu setting changes with Instant Image Update.
7
8
6
5
4
Pressing EXIT will exit Freeze Frame and the display will start to scroll.
Depth
200 kHz Sonar History Window
83 kHz Sonar History Window
Temperature
1
5
6
7
8
Triplog
2
3
4
Upper Depth Range
Lower Depth Range
Speed
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Snapshot and Recording View
Snapshot and Recording View
1
3
Snapshot and Recording View displays and allows you to view both screen
snapshot thumbnails and recording icons captured to an optional-purchase
MMC/SD card installed in your unit. In addition, when you are in the Snapshot
and Recording View, Start Recording, Stop Recording, Delete Image, Delete All
Images, Delete Recording, Delete All Recordings, Pings Per Second, Playback
Speed and Stop Playback are added to the X-Press™ menu.
4
7
6
The Snapshot and Recording View displays up to three screen snapshot
thumbnails or recording icons on the screen at a time; you may have to scroll
using the 4-WAY Cursor keys to see the whole list of thumbnails and/or icons
in this view. The selected thumbnail or icon will be highlighted with arrows.
7
5
2
8
NOTE: The speed of the screen capture or of the recording depends on the type of
card you use; in general, SD cards capture the screen faster than MMC cards do.
Recording icon
Amount of recording left to play
Recording mode icons
1
2
3
4
5
Snapshot thumbnail
Unavailable icon
Information box
6
7
8
Amount of recording that has been played
Amount of space used for this recording
NOTE: For snapshots and recordings, the indicator bar has several states: during
recording, the amount of space remaining on the MMC/SD card is indicated on
the status bar. During playback, the amount of time/memory remaining to play is
indicated on the status bar. When a snapshot thumbnail is highlighted, the
amount of room remaining on the MMC/SD card is indicated.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Screen Snapshot: When Screen Snapshot is enabled (from the Accessories
menu tab), pressing the MARK key creates a saved screen capture (when
you have an optional-purchase MMC/SD card installed). Once you have
created a screen capture, a screen capture thumbnail is added to the
Snapshot and Recording View, and is available to view at a later date. See
the full-sized image by highlighting a thumbnail (using the Up or Down 4-
Way Cursor keys), then using the Right 4-Way Cursor key to view the full
image. A border around the full-size screen snapshot indicates that it is just
a screen snapshot, not a “live” view. You can delete the selected image, or
all images, by selecting a thumbnail and using Delete Image, or using Delete
All Images from the Snapshot and Recording X-Press™ menu.
When you start a screen snapshot, you will see a message that a waypoint
has been created at the point where your cursor is on the screen, and the
screen will freeze while the snapshot is being saved to the MMC/SD card. A
status dialog box will appear that shows the progress of the save as a
percentage, and that displays the numbered file name assigned to the .BMP
file that is being created. Snapshot filenames begin with the letter "S". For
more information, see Accessories Menu Tab: Using Screen Snapshot
procedure and Snapshot and Recording X-Press™ Menu.
Recording and Playback: From the Snapshot and Recording View, you can
use the X-Press™ menu to start and stop recording, and to change the pings
per second (which alters the detail level of the recording). Once you are
recording already, playing back a recording and screen snapshot viewing are
not allowed, and the only Sonar Recording menu choices available in the
X-Press™ menu are Stop Recording and Pings Per Second. Use the 4-WAY
Cursor keys from the Snapshot and Recording View to start playback of a
specific recording icon. You can then cycle through all the views using the
VIEW key to see what those views looked like during the recorded time
period. You can also use the X-Press™ menu to change playback speed, stop
playback, and delete recording icons.
Working with screen snapshots is a four-step process:
1. Enabling Screen Snapshot from the Accessories Menu.
2. Making a Screen Snapshot using the MARK key.
3. Viewing a Screen Snapshot using the Snapshot and Recording View.
4. Deleting a Screen Snapshot using the Snapshot and Recording
X-Press™ menu.
For more information, see Accessories Menu Tab: Using Screen Snapshot
and Snapshot and Recording X-Press™ Menu.
Working with sonar recordings is a six-step process:
1. Displaying the Snapshot and Recording View.
2. Starting a sonar recording using the Snapshot and Recording
X-Press™ menu.
3. Changing the maximum ping rate for the recording using the
Snapshot and Recording X-Press™ menu (optional).
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording Slider Bar
4. Stopping a recording using the Snapshot and Recording X-Press™
menu.
1
5
5. Playing back a recording, using the Snapshot and Recording View
and the 4-Way Cursor keys, and changing the playback speed using
the Snapshot and Recording X-Press™ menu.
4
7
3
6
8
6. Deleting a recording using the Snapshot and Recording X-Press™
menu.
For more information, see Snapshot and Recording X-Press™ Menu.
2
8
When you start a sonar recording, you will see a message that a waypoint
has been created at your current location. During recording, playing back a
recording and screen snapshot viewing are not allowed. An information box
displays a variety of information including the numbered file name assigned
to the .SON file that is being created. The slider bar at the bottom of the
screen shows the progress of the recording as well as how much space is
remaining on the MMC/SD card.
9
Recording Indicator
Current Ping Rate
Average Ping Rate
1
2
3
4
5
6
7
8
9
Amount of space and time used by this recording
Name of recording
Amount of space remaining on card
Total amount of space on card
Time and Date recording was started
Position where recording was started
10
NOTE: The waypoints that are created by a recording have the same name as the
file and use a custom waypoint icon. Recording filenames begin with the letter "R".
Highlighting a recording: You can scroll through the whole list of recording
icons available in the Snapshot and Recording View using the 4-WAY Cursor
keys. The highlighted icon will be surrounded by arrows, and a green play
triangle will appear to its right.
For more information, see Snapshot and Recording X-Press™ Menu.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording Playback
Playing back a recording: Highlight a recording icon (using the Up or Down
4-Way Cursor keys), then use the Right 4-Way Cursor key to start playback.
During playback, all active navigation is cancelled, all other thumbnails and
icons will disappear, and a "Playback" message box similar to the Simulation
message will be displayed periodically. When playback begins, the view is
automatically switched to the primary Sonar View for your model, and no live
sonar data will be displayed; only recorded sonar and GPS data will be
shown, and the Snapshot and Recording View will display the playback
status. You can change the speed, skip to the beginning or end of playback,
and even reverse playback, using the Playback Speed X-Press™ menu item,
and stop the playback using the Stop Playback X-Press™ menu item; these
items are added to the X-Press™ menus in all views during playback. In the
Snapshot and Recording View only, playback speed can also be changed
using the Left and Right 4-Way Cursor keys. Playback is paused when the
sonar cursor is active and resumes playing when the cursor is removed.
Playback is automatically paused when the end of the recording is reached.
4
2
3
5
6
7
8
1
9
10
Average ping rate
Amount of time already played
Name of recording
1
2
3
4
5
6
7
Amount of time remaining to play
Playback speed icons
Time and Date recording started
Position when recording started
Current playback ping rate
8
NOTE: Sonar chart speed is increased during Fast Forward and reversed during
Rewind. This may reduce the quality of the sonar image, since at higher speeds,
not every sonar return can be processed and displayed.
Amount of time remaining to play
Overall length of recording
9
10
You can delete the highlighted recording, or all recordings, using Delete
Recording or Delete All Recordings from the Snapshot and Recording
X-Press™ menu.
NOTE: Navigation is not affected by the Sonar Recording feature, but any active
navigation is cancelled when playback begins or ends.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Default layout: The top portion of the display presents a historical log of
sonar returns from the 200 kHz down-looking sonar beam. New information
in the down beam panel scrolls from right to left. The bottom portion of the
display presents a historical log of sonar returns from the 455 kHz right- and
left-looking sonar beams. New information in the side beam panels scrolls
from the center out.
Side Beam View
(only with QuadraBeam PLUS™ transducer)
Side Beam View is only available if you have connected a QuadraBeam™
transducer accessory (included with the 957 and optional-purchase on the
917) and when Transducer Select is set to QuadraBeam (see Sonar Menu
Tab: Transducer Select). On the 917, the QuadraBeam PLUS™ transducer
requires a separate purchase. This view shows sonar information from both
the left and right 455 kHz beams and the 200 kHz down-looking beam in one
view. You can customize the way the sonar data is displayed in the Side
Beam View to suit your personal preferences. Depending on the layout
selected from the Quad Layout Sonar X-Press™ menu (only available on the
Sonar X-Press™ menu when in Side Beam View), the display will represent
the same sonar data in one of the following three layouts: Default, Classic,
and Slanted.
Side Beam View, Default Layout
1
4
5
6
3
2
Depth
200 kHz Sonar History Window
Water Surface Line for 455 kHz Sonar History Windows
Right Side 455 kHz Sonar History Window
1
4
Temperature
2
3
5
6
Left Side 455 kHz Sonar History Window
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Classic layout: The top portion of the display presents a historical log of
sonar returns from the 200 kHz down-looking sonar beam. New information
in the down beam panel scrolls from right to left. The bottom portion of the
display presents a historical log of sonar returns from the 455 kHz right- and
left-looking sonar beams. New information appears at the top, and scrolls
down the display.
Slanted layout: This layout presents the two 455 kHz side sonar beams and
the 200 kHz down-looking sonar beam as three panels of historical data. This
layout is presented as three slanted panels. New information appears on the
right, and scrolls to the left.
Side Beam View, Slanted Layout
1
Side Beam View, Classic Layout
1
5
5
5
4
2
2
6
3
4
6
3
5
Depth
200 kHz Sonar History Window
1
4
5
Water Surface Line for 455 kHz
Sonar History Windows
Temperature
2
3
Left Side 455 kHz Sonar History Window
Depth
200 kHz Sonar History Window
1
4
5
Right Side 455 kHz Sonar History Window
6
Water Surface Line for 455 kHz
Sonar History Windows
Temperature
2
3
In all of these layouts, the sonar information from the side-looking beams
reveals bottom contour, structure and fish similar to the down-looking beam,
but the area covered is to the left and right of the area shown in the down-
looking portion, so you actually see more of the bottom. The distance
covered by the right and left beams is based on the depth setting for the
down-looking beam, up to a maximum of 160 feet.
Left Side 455 kHz Sonar History Window
Right Side 455 kHz Sonar History Window
6
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Bird’s Eye View
Bird’s Eye View
Bird's Eye View shows a 3D perspective view of the track and the chart land
contour from a point above and behind the boat (the eye point). As the boat
turns, the eye point moves to follow the boat. Big Digits on this view provide
digital data in a large, easy-to-see format.
1
2
3
5
When you press the 4-WAY Cursor key in the Bird’s Eye View, the position of
the eye point will shift. This allows you to move and turn the eye point so
that you can look off to the sides, or even behind the boat. Pressing the
RIGHT or LEFT arrow keys on the 4-WAY Cursor key turns the eye point right
or left, while pressing the UP arrow key moves the eye point forward, and
pressing the DOWN arrow key moves the eye point backward.
6
4
Pressing the EXIT key moves the eye point back to its original position behind
and above the boat.
Depth
Speed of Boat
Land Contours
Boat Icon
1
4
5
6
Course: Direction that boat is travelling
relative to North Reference
Latitude and Longitude Position of Boat
2
3
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Chart/Bird’s Eye Combo View
Chart/Bird’s Eye Combo View
6
8
7
Chart/Bird’s Eye Combo View shows both the Chart and Bird’s Eye views in a
combination split screen. You can perform any of the functions for either of
these views, but only when the view you want to control is selected as the
active side (see Sonar X-Press™ Menu: Active Side or Navigation X-Press™
Menu: Active Side for more information). A green arrow points to the side that
is active. You can also adjust the size of the left side of a split screen (see Sonar
X-Press™ Menu: Split Position or Navigation X-Press™ Menu: Split
Position for more information).
1
2
9
9
10
4
3
5
NOTE: See Bird’s Eye View and Chart View for more information about each
4
side of this view.
11
5
Depth
Latitude and Longitude Position of Cursor
Distance to the Cursor
Bearing to the Cursor
Cartography
1
6
7
Course: Direction that boat is travelling
relative to North Reference
2
8
Bird’s Eye Window
Boat Icon
3
4
5
9
Active Cursor
10
11
Track (Breadcrumb Trail)
Chart Window
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Chart/Chart Combo View
Chart/Chart Combo View
6
8
7
Chart/Chart Combo View shows two versions of the Chart view in a
combination split screen, so that you can see the position of the boat on one
side while you zoom in or perform other functions on the other. You can
perform any of the functions for the Chart view, but only on the side of the
view you have selected as the active side (see Sonar X-Press™ Menu: Active
Side or Navigation X-Press™ Menu: Active Side for more information). A
green arrow points to the side that is active. You can also adjust the size of the
left side of a split screen (see Sonar X-Press™ Menu: Split Position or
Navigation X-Press™ Menu: Split Position for more information).
1
2
9
9
10
4
4
5
5
NOTE: See Chart View for more information about each side of this view.
3
11
Depth
Latitude and Longitude Position of Cursor
Distance to the Cursor
Bearing to the Cursor
Cartography
1
6
7
Course: Direction that boat is travelling
relative to North Reference
2
8
Chart Window 1
Boat Icon
3
4
5
9
Active Cursor
10
11
Track (Breadcrumb Trail)
Chart Window 2
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Chart View with Active Cursor
Chart View
7
5
6
Chart View shows cartography from the built-in UniMap™ or an optional
MMC/SD map for the area surrounding your current position. The current
track (also known as the position history or breadcrumb trail) showing where
the boat has been, along with saved tracks, waypoints, and the current route
(when navigating), are overlaid on the chart. You can use the 4-WAY Cursor
Control key to shift/pan the chart to another area. You can use the ZOOM
(+/-) keys to zoom in and out. You can use the INFO key to get information
on the chart objects near the cursor.
1
2
10
4
9
3
8
Depth
Distance to the Cursor
Bearing to Cursor
Cartography
1
6
7
Course: Direction that boat is travelling
relative to North Reference.
2
8
Track (Breadcrumb Trail)
3
4
5
Active Cursor
9
Map Scale
Boat Icon
10
Latitude and Longitude Position of Cursor
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Chart/Sonar Combo View
Chart/Sonar Combo View
Chart/Sonar Combo View shows both the Chart and Sonar views in a
combination split screen. You can perform any of the functions for either of
these views, but only when the view you want to control is selected as the
active side (see Sonar X-Press™ Menu: Active Side or Navigation X-Press™
Menu: Active Side for more information). A green arrow points to the side that
is active. You can also adjust the size of the left side of a split screen (see Sonar
X-Press™ Menu: Split Position or Navigation X-Press™ Menu: Split
Position for more information).
1
2
6
5
4
3
NOTE: See Sonar View and Chart View for more information about each side of
this view.
8
7
Depth
Boat Icon
Carotgraphy
1
5
6
7
8
Course: Direction that boat is travelling
relative to North Reference
Track (Breadcrumb Trail)
2
Sonar Window
Chart Window
3
4
Map Scale
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Chart View with Cursor Present
Chart Orientation
All the chart views allow you to choose the orientation of the chart. When
North-Up orientation is selected, True North is shown at the top of the
display. In other words, objects located to the north of the boat are drawn
above the boat. When Course-Up orientation is selected, the direction of
motion of the boat is shown at the top of the display. In other words, objects
ahead of the boat are drawn above the boat. In both orientations, the view
pans automatically, so that the boat is always centered on the display. When
the boat is stationary, it is drawn as a circle. When the boat is in motion, it
takes on a boat shape, pointed in the direction of motion (always Up in the
Course-Up orientation). See Navigation Menu Tab: Chart Orientation for
more information.
Viewing Cartography
Zooming: Use the Plus (+) key to Zoom In and the Minus (-) key to Zoom Out
showing the cartography at different scales. The scale is indicated on the left
side of the display. If you zoom in beyond the available chart data, the
display will go into Overzoom mode whereby the last available chart data is
amplified to reflect the scale selected. If you zoom in so far that no
cartography is available, a lat/lon grid will be drawn instead.
In the Chart or Combo Views, there are several cartography-related
functions that you can access using various keys.
Panning: Use the 4-WAY Cursor keys to move the chart around on the
display in the direction of the key being pressed. When you do this, a
Bullseye Cursor is drawn at the top of the screen and is linked to the boat by
a yellow line, even if the boat is off the screen. At the same time, a cursor
dialog box is displayed at the top of the screen with the distance and bearing
from the boat to the cursor position and the latitude/longitude coordinates
of the cursor. When the cursor is active on the display, you can also use the
4-WAY Cursor Control key to move the cursor diagonally.
Chart Info: Use the INFO key to get detailed information about the chart. If
the cursor is active, you will see information about the chart objects located
near the cursor. If the cursor is not active, the Chart Info menu will appear.
You can select the nearest port, the nearest tide station, or the nearest
current station to see information about any of these objects.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: The built-in UniMap™ does not contain any Port, Tide or Current information.
This information is only available from optional-purchase MMC/SD cards.
Navigation
Use the 900 Series™ to establish waypoints at areas of interest and to
navigate to those waypoints via a saveable route (representing the shortest
intended distance between waypoints). You can also view and save tracks,
which represent the actual path of the boat.
Nearest Port: The position and services information for the nearest port to
your present position will be displayed. Press the EXIT key to remove the
information box and the Bullseye Cursor will be centered over the port
position. The Cursor Information Boxes will indicate the distance and bearing
to the port from your present position.
Nearest Tide Station: Tide information for the nearest tide station to your
present position will be displayed. This includes the position of the station
and the times of the high and low tides for today’s date. A tide graph is also
displayed showing the rise and fall of the tides for the 24 hour time period
encompassing the date. You can change the date to look at tide information
before or after the date displayed by pressing the LEFT or RIGHT Cursor key
respectively. Press the EXIT key to remove the information box and the
Bullseye Cursor will be centered over the tide station position. The cursor
information boxes will indicate the distance and bearing to the tide station
from your present position.
Nearest Current Station: Current information for the nearest current station to
your present position will be displayed. This includes the position of the station and
the current changes for today. Two graphs are also presented that show the time,
direction and flow speed of the current changes for the 24 hour time period of
today’s date. You can change the date to look at current information before or after
the date displayed by pressing the LEFT or RIGHT Cursor key respectively. Press the
EXIT key to remove the information box and the Bullseye Cursor will be centered
over the current station position. The Cursor Information Boxes will indicate the
distance and bearing to the current station from your present position.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Routes link two or more waypoints together to create a path for navigation,
and are used in trip planning. You can link individual waypoints together by
using the GOTO key. A route represents your intended navigation and shows
the shortest path from each waypoint to the next. As you travel a route,
staying on the route line is the most efficient way to get to your destination,
although you should always look out for obstacles not shown on the chart.
Your 900 Series™ can store up to 50 routes that can each contain up to 50
waypoints.
Waypoints, Routes and Tracks
Waypoints are stored positions that allow you to mark areas of interest or
navigation points. Your 900 Series™ can store up to 3000 waypoints.
Waypoints, Routes and Tracks
1
2
Tracks consist of detailed position history, and are displayed as a
breadcrumb trail of trackpoints. The Current Track shows the position history
since the unit was powered up (maximum of 20,000 trackpoints displayed).
You can clear the Current Track or save it at any time. Your 900 Series™ can
store up to 50 saved tracks, each containing 20,000 trackpoints. The current
track represents your actual path so far.
8
9
11
3
10
4
5
6
7
Depth
TTG: Estimate of Trip Time to Destination Waypoint
1
6
7
Course: Direction that boat is traveling
relative to North Reference
Bearing: Direction to Destination Waypoint
Relative to North Reference
XTE: Cross Track Error. Distance of Boat
from Route
DTG: Distance to Go to Waypoint
Speed Over Ground: Speed of Boat
Waypoint
2
3
4
5
8
Route
9
Off-Course Alarm Limits
Map Scale
10
11
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Edit a waypoint: From the Waypoints submenu, select Edit and press the
RIGHT Cursor key to display a list of saved waypoints. Select the waypoint
you want to edit and press the RIGHT Cursor key. Use the 4-WAY Cursor
Control key to move from field to field, and the UP and DOWN Cursor keys
to changes values once you are in a field. In the Waypoint Name, Latitude
and Longitude fields, use the UP and DOWN Cursor keys to change the letter
or number. All upper and lower case letters are available, as well as digits 0-
9 and some punctuation characters. In the Waypoint Icon field, use the UP
and DOWN Cursor keys to change the icon used to represent the waypoint
on the Combo and Chart Views. You can exit these fields with the LEFT and
RIGHT Cursor keys or by pressing the EXIT key. Select Save and press the
RIGHT Cursor key to save your changes.
Save, Edit, or Delete a Waypoint
Save your current position as a waypoint: On any view, press the MARK
key to save the current position of the boat as a waypoint.
Save the cursor position as a waypoint: On the Chart or Combo view, use the
Cursor key to designate the position you want to save as a waypoint. Then press
the MARK key to save the marked position as a waypoint.
Save a position from the sonar history: Use the Cursor key to point to a
feature in the sonar history (also called the Sonar Saver feature). Press the
MARK key to create a waypoint at the location where that sonar reading was
taken. The new waypoint will also record the depth at that location.
To make it easier to select a waypoint, select Sort By and press the RIGHT or
LEFT Cursor keys to select a sort order:
NOTE: When you save a waypoint by any of these methods, a numerical
waypoint name is automatically assigned. You can edit the waypoint information
later to give it a different name and select an icon to represent it (see Waypoint
submenu on the Navigation Main Menu Tab).
• Name shows the waypoints alphabetically
• Time shows the most recently-created waypoint first
• Distance shows the closest waypoint first.
Display the Waypoints Submenu: From any view, press the MENU key
twice to display the Main Menu System, then use the RIGHT Cursor key to
select the Navigation tab. Select Waypoints and press the RIGHT Cursor key
to display the Waypoints submenu.
Delete a waypoint: From the Waypoints submenu, select Delete and press
the RIGHT Cursor key to display a list of waypoints. Select the waypoint you
want to delete, then press the RIGHT Cursor key. You will be asked to confirm
deletion before the waypoint is actually deleted.
Program a specific position as a waypoint: To create a waypoint that is
NOT your current position, from the Waypoints submenu, select the Create
option and press the RIGHT Cursor key. Use the Cursor keys to program a
waypoint name, latitude, longitude, and icon before selecting Save.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Navigate to a Waypoint or Position
Add a Waypoint Target or Trolling Grid
Navigate to the cursor position: From any Chart or Combo view, use the
Cursor key to select a position or waypoint to which you want to navigate.
Press the GOTO key. Navigation will begin immediately.
Add or Remove a Waypoint Target: From the Waypoints submenu
(accessed from the Navigation main menu), select Target and press the
RIGHT Cursor key to display a list of waypoints. Select the waypoint you
want to target. A target consisting of concentric circles centered on the
selected waypoint will appear on all of the navigation views; the target
shows various distance ranges from the targeted waypoint. To remove the
target, choose Remove Target from the Navigation X-Press™ Menu.
Navigate to a specified waypoint: Press the GOTO key, then choose the
waypoint to which you would like to navigate from the waypoint list and
press the RIGHT Cursor key to select it.
NOTE: By repeating the previous instructions, you can add more waypoints to
create a longer multi-segment route.
NOTE: Only one waypoint can have either a target or a grid at one time. If you
apply a target or a grid to a new waypoint, the original waypoint will lose its
target or grid.
Skipping a waypoint: From the Navigation X-Press™ Menu, select Skip Next
Waypoint and press the RIGHT Cursor key. If there is not another waypoint
to skip to, navigation will be cancelled.
Chart View with Target
Cancel navigation: From the Navigation X-Press™ Menu, select Cancel
Navigation and press the RIGHT Cursor key. Canceling navigation removes
the route and any waypoints created using the GOTO key, but does not
remove any saved routes from memory. You will be prompted to save the
current route when you cancel navigation.
2
1
Map Scale
Waypoint Target
1
2
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Add or Remove a Trolling Grid: From the Waypoints submenu (accessed from
the Navigation main menu), select Grid and press the RIGHT Cursor key to display
a list of waypoints. Select the waypoint to which you want to add the grid. The
trolling grid will appear on all of the navigation views, and can be used as a guide
when trolling around a waypoint. The grid can be rotated to any desired heading
using Grid Rotation from the Navigation Main menu. To remove the trolling grid,
choose Remove Grid from the Navigation X-Press™ Menu.
Save, Edit or Delete a Route
Save the current route: While you are navigating, the current route can be
saved. From the Navigation X-Press™ Menu, select Save Current Route and
press the RIGHT Cursor key. Navigation will continue.
Display the Routes submenu: From any view, press the MENU key twice to
display the Main Menu System, then use the RIGHT Cursor key to select the
Navigation tab. Select Routes and press the RIGHT Cursor key to display the
Routes submenu.
Chart View with Grid
Create a route: From the Routes submenu, select Create and press the
RIGHT Cursor key. A Route Edit screen will be displayed with an empty route.
You can name the route, add waypoints to the route from the list of all
waypoints, and order the waypoints in the route using the Cursor keys.
2
1
Edit a saved route: From the Routes submenu, select Edit and press the
RIGHT Cursor key. A Route Edit screen will be displayed. Select the route you
wish to edit and press the RIGHT Cursor key. Re-name the route or change,
delete or re-order the waypoints used in the route.
Delete a saved route: From the Routes submenu, select Delete and press
the RIGHT Cursor key. Select the route you wish to delete and press the
RIGHT Cursor key. You will be asked to confirm your choice by pressing the
RIGHT Cursor key again before the route is deleted.
Map Scale
Waypoint Trolling Grid
1
2
NOTE: Only one waypoint can have either a target or a grid at one time. If you
apply a target or a grid to a new waypoint, the original waypoint will lose its
target or grid.
Travel a saved route: From the Routes submenu, select Travel and press the
RIGHT Cursor key. A list of saved routes will appear. Select the route you
wish to travel and press the RIGHT Cursor key to make this route the current
route and begin navigation. You may also travel the route in either forward
or reverse order.
NOTE: The spacing of the rings on the waypoint target and the spacing of the grid
lines on the trolling grid is the same as the length of the scale bar on the left edge
of the display. Zooming in or out will decrease or increase the spacing, respectively.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Route Info: From the Routes submenu, select Info and press the RIGHT
Cursor key. A list of saved routes will appear. Select the route for which you
want information, and press the RIGHT Cursor key. The list of waypoints in
the route will be shown, with the distance and bearing from each waypoint
to the next, as well as the distance and bearing from the current position to
the first waypoint in the route.
Edit, Delete or Hide Saved Tracks
Display the Tracks Submenu: From any view, press the MENU key twice to
display the Main Menu System, then use the RIGHT Cursor key to select the
Navigation tab. Select Tracks and press the RIGHT Cursor key to display the
Tracks submenu.
Edit a saved track: From the Tracks submenu, select Edit and press the
RIGHT Cursor key to display the list of saved tracks. Select the track you want
to edit and press the RIGHT Cursor key. When the Edit Track dialog box
appears, use the Cursor keys to move between fields. In the Track Name
field, the UP and DOWN Cursor keys change the letter or number. All upper
and lower case letters are available, as well as digits 0-9 and some
punctuation characters. You can exit the Track Name field with the LEFT and
RIGHT Cursor keys or by pressing the EXIT key. Select Save and press the
RIGHT Cursor key to save your changes.
Save or Clear a Current Track
Save the current track: From the Navigation X-Press™ Menu, select Save
Current Track and press the RIGHT Cursor key. The track will remain on the
display, but will change from black to gray. To remove the track completely
from the display, see Edit, Delete or Hide Saved Tracks.
NOTE: When you save a track, a name is automatically assigned. The track name
consists of a date/time stamp, but can be re-named later (see Edit, Delete, or
Hide Saved Tracks).
Delete a saved track: From the Tracks submenu, select Delete and press the
RIGHT Cursor key to display the list of saved tracks. Select the track you want
to delete and press the RIGHT Cursor key. You will be asked to confirm
deletion before the track is actually deleted.
Clear the current track: From the Navigation X-Press™ Menu, select Clear
Current Track and press the RIGHT Cursor key. The track will be removed
from the display and discarded.
Hide or display a saved track: From the Tracks submenu, select Visibility
and press the RIGHT Cursor key to display the list of saved tracks. Select the
track you want to hide or display and use the Cursor keys to select Hidden
or Visible. Press the EXIT key to return to the Tracks submenu.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Cancel MOB navigation: From the Navigation X-Press™ menu, select
Cancel MOB and press the RIGHT Cursor key. Canceling MOB navigation
removes the route and any waypoints created using the GOTO key, but does
not remove any saved routes from memory.
Man Overboard (MOB) Navigation
As soon as you know that you have a man overboard, you should activate
MOB navigation to maximize chances for a successful rescue. MOB
navigation allows you create an MOB waypoint to locate the point at which
your man went overboard, and the relation of the boat to that point. When
MOB is activated, an MOB waypoint, which is a permanent, sharable
waypoint with a large, distinctive icon, is created at the boat's current
position (regardless of whether the chart cursor is active or not). Any current
navigation will be cancelled and the current route discarded without user
notification, and MOB navigation will begin immediately. A line will be
drawn from the boat's current position to the MOB waypoint, and the MOB
waypoint will be targeted. The view is switched to the Chart View
automatically when MOB is activated, and an additional info box that shows
the lat/lon position of the MOB waypoint and the elapsed time since MOB
was activated is added to the Chart View.
MOB Navigation
4
3
5
2
1
It is not possible to re-activate MOB or modify the current route without first
canceling MOB navigation. The Off Course trigger is also disabled and the
Off Course Alarm circle is not drawn. Any press of the GOTO key, or selection
of a GOTO menu item, will cause an error beep and a short message will be
displayed to the user that will disappear after 2 seconds.
Position where man fell overboard
Elapsed time since MOB was activated
Boat icon
Target surrounding MOB waypoint
MOB waypoint
1
2
3
4
5
6
Activate MOB navigation: Press and hold the GOTO key for more than 1.5
seconds to activate the Man Overboard (MOB) function.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Press the MENU key twice for the Main
Menu, then use the 4-WAY Cursor LEFT or
RIGHT key to select a tab, and use the
DOWN or UP key to select a specific menu
item under that tab, then use the LEFT or
RIGHT keys again to change a menu setting.
Press the EXIT key to move quickly to the top
of the tab. A down arrow at the bottom of a
menu means that you can scroll to additional
menu choices using the DOWN Cursor key. A
right or left arrow on a menu choice means
that you can use the RIGHT or LEFT Cursor
keys to make changes or to see more
information.
The Menu System
The menu system is divided into easy-to-use menu modules. The main
components of the menu system are:
Start-Up Options Menu: Press the MENU key during the power up
sequence to view the Start-Up Options menu. See Start-Up Options Menu.
X-Press™ Menu: The X-Press™ Menu
allows you to access the settings that are
changed frequently without having to
navigate through the whole menu system.
Press the MENU key once to display the
X-Press™ Menu. When you select a menu
item from the X-Press™ Menu, the menu will
collapse, leaving only the menu choice on
the screen. Use the UP or DOWN Cursor keys
Main Menu System
Normal User Mode
NOTE: The Main Menu choices will vary depending on whether you are in
Normal or Advanced User Mode, and what model you own.
to reactivate the X-Press™ Menu.
X-Press™ Menu
User Mode (Normal or Advanced): An Advanced Mode is provided for
users who desire the highest level of control over the 900 Series™ and
Normal Mode for users who desire greater simplicity and fewer menu
choices. Additional Advanced menu choices will be displayed throughout
the menu system when you navigate to specific menus while in Advanced
Mode. Any changes made while in Advanced Mode will remain in effect
after you switch back to Normal Mode. See Setup Menu Tab: User Mode
for specific instructions on changing to the User Mode.
NOTE: The X-Press™ Menu choices will vary depending on which view is active when
you press the MENU key, as well as whether you are in Normal or Advanced User
Mode. Either the Sonar or Navigation X-Press™ Menu will appear, depending on the
view you are in.
Main Menu Tabs: Less frequently-adjusted menus are grouped into the
Main Menu System. The Main Menu system is organized under main tab
menu headings to help you find a specific menu item quickly. Main tab
headings are: Alarms, Sonar, Navigation, Chart, Setup, Views, and
Accessories.
NOTE: The 900 Series™ defaults to Advanced User Mode on start-up.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Start-Up Options Menu
Press the MENU key when the Title screen is displayed to access the Start-
Up Options menu.
Start-Up Options Menu
Sonar Tab, Normal Mode
Use the UP or DOWN 4-WAY Cursor keys to position the cursor, then the
RIGHT Cursor key to select one of the following choices. If you wait too long,
the system will default to whichever menu mode happens to be highlighted:
• Normal
• Simulator
• System Status.
Sonar Tab, Advanced Mode
Total Screen Update: when you change any menu settings that affect the
Sonar View, the view will update immediately (i.e. you don’t have to exit the
menu to apply the change to the screen).
See the following paragraphs for more information about each of these choices.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: To get the full benefit of the Simulator, it is important to select Simulator
manually from the Start-Up Options menu as opposed to letting the 900 Series™
enter Simulator automatically (as it will if a transducer is not connected and you
do nothing during power up). Manually selecting Simulator from the Start-Up
Options menu allows you to pre-configure your 900 Series™ for on-the-water
operation. Any menu changes you make will be saved for later use.
Normal Operation
Use Normal operation for on-the-water operation with a transducer
connected. In addition, your 900 Series™ uses advanced transducer
detection methods to determine if a transducer is connected. If a functioning
transducer is connected, Normal operation will be selected automatically at
power up and your 900 Series™ can be used on the water.
A Simulation message will appear on the display periodically to remind you
that you are using the Simulator.
Exit Normal operation by powering your 900 Series™ off.
Exit the Simulator by powering your 900 Series™ off.
Simulator
Use the Simulator to learn how to use your 900 Series™ before taking your
boat on the water. The Simulator is a very powerful tool that simulates on-the-
water operation, providing a randomly-updated display. We recommend going
through this manual while using the Simulator, since all of the menus function
and affect the display the way they actually do when in Normal operation.
System Status
Use System Status to view system connections and to conduct a unit self-
test. Exit System Status by powering your 900 Series™ off.
The following screens are displayed in turn when you press the VIEW button
when using System Status:
Simulator
• Self Test
• Accessory Test
• GPS Diagnostic View
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Self Test
Accessory Test
Self Test displays results from the internal diagnostic self test, including unit
serial number, Printed Circuit Board (PCB) serial number, software revision,
total hours of operation and the input voltage.
Accessory Test lists the accessories connected to the system.
Accessory Test Screen
Self Test Screen
NOTE: The speed accessory will be detected only if the paddlewheel has moved
since your 900 Series™ was powered up.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
This view also reports the current position, local time and date, and other
numeric information. The current GPS Fix Type is reported as No Fix, 2D Fix,
3D Fix, or Enhanced. An Enhanced fix has been augmented using
information from WAAS, EGNOS, or MSAS. A 3D or Enhanced Fix is required
for navigation. HDOP (the Horizontal Dilution of Precision) is a GPS system
parameter which depends on the current satellite configuration. HDOP is
used to calculate the Estimated Position Error.
GPS Diagnostic View
GPS Diagnostic View, which is only available when a GPS Receiver is
attached to you 900 Series, shows a sky chart and numerical data from the
GPS receiver. The sky chart shows the location of each visible GPS satellite
with its satellite number and a signal strength bar. A dark grey bar indicates
that the satellite is being used to determine your current position. A light gray
bar indicates that the satellite is being monitored, but is not yet being used.
GPS Diagnostic View
1
4
2
3
Sky Chart
Current Latitude and Longitude
Satellite Being Monitored
1
2
3
4
Satellite Being Used
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Sonar X-Press™ Menu
Active Side
The Sonar X-Press™ Menu provides access
to the settings most frequently used. Press
the MENU key once while in any of the
Sonar Views to access the Sonar X-Press™
Menu.
Active Side allows you to select which side
of a Combo View will be active; key presses will only affect the active side of
the screen. When a menu is displayed, the non-active side of the screen will
be grayed out; at any other time, a green arrow will point to the active side.
Combo Views usually display sonar on the left, with charts or Bird’s Eye
usually on the right. The Active Side menu choice is only available when a
Combo View is active.
NOTE: Menu choices will vary depending on
system settings such as whether the unit is set
for Advanced User mode.
To select the Active Side:
1. Highlight Active Side on the Sonar X-Press™ Menu.
NOTE: Quad Layout only appears in Side Beam
View with the QuadraBeam PLUS™ transducer
(standard in the 957c Combo model, optional-
purchase in the 917c Combo model).
2. Use the RIGHT 4-WAY Cursor Control key to change which side is
active. (Left, Right, Default = Left, or Sonar).
Sonar X-Press™ Menu
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Split Position
To adjust the Sensitivity:
Split Position allows you to adjust what
percentage of the screen is taken up by the left side of any Combo View;
each view may be adjusted independently; you must be in a specific view to
adjust the screen size for that view. The number setting indicates the
percentage taken up by the left side of the Combo View; selecting Left sets
the left side of the screen to its smallest setting. The Split Position menu
choice is only available when a Combo View is active.
1. Highlight Sensitivity on the Sonar
X-Press™ menu.
2. Use the LEFT or RIGHT 4-WAY
Cursor Control keys to increase or
decrease the Sensitivity setting.
(Low = 1, High = 20, Default = 10)
Sensitivity at Low
Sensitivity at Medium
Sensitivity at High
To Adjust Split Screen Position
1. Highlight Split Position on the Sonar X-Press™ Menu.
2. Use the RIGHT 4-WAY Cursor Control key to change the size of the left
side of a Combo View. (Left,30, 40, 50, 60, 70, Right, Default varies)
Sensitivity
Sensitivity controls how much detail is shown
on the display. Increasing the sensitivity shows more sonar returns from small
baitfish and suspended debris in the water; however, the display may become
too cluttered. When operating in very clear water or greater depths, increased
sensitivity shows weaker returns that may be of interest. Decreasing the
sensitivity eliminates the clutter from the display that is sometimes present in
murky or muddy water. If Sensitivity is adjusted too low, the display may not
show many sonar returns that could be fish.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Upper Range
Lower Range
(Advanced: Sonar, Split Sonar and
Active Sonar Side Views only)
Lower Range sets the deepest depth range
that will be displayed. Automatic is the default setting. When in automatic
mode, the lower range will be adjusted by the unit to follow the bottom.
Selecting a specific setting locks the depth range into Manual mode. Use
both Upper and Lower Range together to view a specific depth range
manually when looking for fish or bottom structure. M will be displayed in
the lower right corner of the screen when you start manually adjusting the
Lower Range to indicate that you are in Manual mode.
Upper Range sets the shallowest depth range that will be displayed on the
Sonar, Split Sonar and Active Sonar Side Views. The Upper Range menu
choice is available when User Mode is set to Advanced (see Setup Menu
Tab: User Mode) and can only be accessed from the Sonar, Split Sonar and
Active Sonar Side Views. Upper Range is often used with Lower Range.
For example, if you are only interested in the area between 20 and 50
feet deep, you should set the Upper Depth Range to 20 and the Lower
Depth Range to 50. The Sonar View will then show the 30 foot area
between 20 and 50, and will not show the surface or the bottom
(assuming the bottom is deeper than 50 feet), and will show greater
detail for that area between 20 and 50 feet.
For example, if you are fishing in 60 feet of water but are only
interested in the first 30 feet (surface to a depth of 30 feet) you
should set the Lower Depth Range limit to 30. The display will show
the 0 to 30 foot range, allowing you to see a more detailed view than
you would see if the display went all the way to the bottom.
NOTE: A minimum distance of 10 feet will be maintained between the Upper and
Lower Range regardless of the manual settings entered.
NOTE: A minimum distance of 10 feet will be maintained between the Upper and
Lower Range regardless of the settings entered manually.
To adjust the Upper Range:
To adjust the Lower Range:
1. Make sure you are in Advanced Mode, then highlight Upper Range
on the Sonar X-Press™ Menu.
1. Highlight Lower Range on the Sonar X-Press™ Menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to increase or
decrease the Lower Range setting. (AUTO, 10 to 1500 feet; 3 to 500
meters [International models only], Default = AUTO)
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to increase or
decrease the Upper Range setting. (0 to 1490 or 0 to 497 meters
[International models only], Default = 0)
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Chart Speed
Quad Layout
(with QuadraBeam PLUS™ Transducer,
Side Beam View only)
Chart Speed determines the speed at which
the sonar information moves across the display, and consequently the
amount of detail shown. A faster speed shows more information in the Sonar
Views and is preferred by most anglers; however, the sonar information
moves across the display quickly. A slower speed keeps the information on
the display longer, but the bottom and fish details become compressed and
may be difficult to interpret. Regardless of the Chart Speed setting, the RTS®
Window will update at the maximum rate possible for the depth conditions.
Adjust Chart Speed to your personal preference.
Quad Layout selects the method used to represent the sonar information
from the two side-looking beams plus the down-looking beam to be
presented on the Side Beam View, and is only available when a QuadraBeam
PLUS™ transducer (optional-purchase for the 917c Combo model, and
standard for the 957c Combo model) is attached and the Side Beam View is
active. Use Quad Layout to change the way the Side Beam View is displayed.
See Side Beam View for more information.
To adjust the Quad Layout:
To adjust the Chart Speed:
1. Highlight Quad Layout on the Sonar X-Press™ menu.
1. Highlight Chart Speed on the Sonar X-Press™ Menu.
2. Use the LEFT or RIGHT 4-Way Cursor Control keys to change the Quad
Layout setting for the Side Beam View. (Default, Classic, Slanted,
Default = Default)
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to increase or
decrease the Chart Speed setting. (1-10, where 1 = Slowest,
10 = Fastest, Default = 5)
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Bottom Lock
(Sonar Zoom View only)
Sonar Colors
Sonar Colors allows you to select which
color palette you would like to use for the display.
Bottom Lock changes the mode of the Zoomed view in the Sonar Zoom View.
To change the Sonar Colors:
To turn on Bottom Lock:
1. Highlight Sonar Colors on the Sonar X-Press™ menu.
1. In the Sonar Zoom View, highlight Bottom Lock on the Sonar
X-Press™ Menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
color palette. (Standard, Gray, Inverse, Green, Default = Standard)
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
Bottom Lock setting to on. (Off, On, Default = Off).
Cancel Navigation
(only when Navigating)
Bottom Range
(Sonar Zoom View only, when Bottom Lock is On)
Cancel Navigation discards the current route and exits Navigation Mode.
This menu choice will only appear when you are currently navigating a route.
This will not delete a previously-saved route.
Bottom Range allows you to control how much of the water column,
measured up from the bottom, is shown in the Sonar Zoom View. Choose a
small value to see low-lying bottom structure or details of the bottom return.
Choose a larger value to see large structure in deeper water. It is possible
to set the Bottom Range to be greater than the depth. In this case, you may
see surface clutter in a wavy band that mirrors changes in the depth.
To Cancel Navigation:
1. Highlight Cancel Navigation on the Sonar X-Press™ menu.
2. Use the RIGHT 4-WAY Cursor Control key to initiate canceling
navigation.
To adjust the Bottom Range:
1. In the Sonar Zoom View, highlight Bottom Lock on the Sonar X-Press™
Menu.
3. The Confirm dialog box will appear. To cancel navigation, press the
RIGHT Cursor key once more. To avoid canceling navigation, press
the LEFT Cursor key.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
Bottom Lock setting to on. (Off, On, Default = Off).
3. Once you turn on Bottom Lock, the Bottom Range X-Press™ menu
choice will be displayed. (10 - 60 feet or 3-20 meters [International
Models only], Default = 15 feet)
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Navigation X-Press™ Menu
Active Side
The Navigation X-Press™ Menu provides
access to the settings most frequently used.
Press the MENU key once while in the Bird's
Eye View, the Chart or the Chart/Sonar
Combo, Chart/Chart Combo View, or
Chart/Bird’s Eye Combo View to access the
Navigation X-Press™ Menu.
Active Side allows you to select which side
of a Combo View will be active; key presses will only affect the active side of
the screen. When a menu is displayed, the non-active side of the screen will
be grayed out; at any other time, a green arrow will point to the active side.
Combo Views usually display sonar on the left, with charts or Bird’s Eye
usually on the right. The Active Side menu choice is only available when a
Combo View is active.
To select the Active Side:
NOTE: Menu choices will vary depending on
system settings, such as whether you are
currently navigating.
1. Highlight Active Side on the Navigation X-Press™ Menu.
2. Use the RIGHT 4-WAY Cursor Control key to change which side is
active. (Left, Right, Default = Left).
NOTE: You will have to change Active Side
setting to Right to see the Navigation X-Press™
Menu from a Combo View with a sonar side.
Split Position
Split Position allows you to adjust what
percentage of the screen is taken up by the left side of any Combo View;
each view may be adjusted independently; you must be in a specific view to
adjust the screen size for that view. The number setting indicates the
percentage taken up by the left side of the Combo View; selecting Left sets
the left side of the screen to its smallest setting. The Split Position menu
choice is only available when a Combo View is active.
Navigation X-Press™ Menu
To Adjust Split Screen Position
1. Highlight Split Position on the Navigation X-Press™ Menu.
2. Use the RIGHT 4-WAY Cursor Control key to change the size of the left
side of a split screen. (Left,30, 40, 50, 60, 70, Right, Default varies)
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Target allows you to apply a target to a waypoint selected from the list of
waypoints.
Waypoint [Name]
(Only with an active cursor on a waypoint)
Waypoint [Name] allows you to view the Waypoints submenu for the
Grid allows you to apply a trolling grid to a waypoint selected from the list
waypoint under your cursor.
of waypoints.
To view the Waypoint [Name] Submenu:
Cursor to Waypoint
1. Move the cursor onto an existing waypoint and press the MENU key
once, or use Cursor to Waypoint to select a waypoint from a list of
saved waypoints.
(Chart or Combo view only)
Cursor to Waypoint allows you to quickly move the cursor to any saved
waypoint, so that you can locate it or edit it.
2. Highlight Waypoint [Name] on the Navigation X-Press™ menu.
NOTE: This X-Press™ menu item appears only if you have saved waypoints.
3. Use the RIGHT 4-Way Cursor Control key to view the Waypoints
submenu, which contains the following menu choices:
To move cursor to a saved waypoint:
1. Highlight Cursor to Waypoint on the Navigation X-Press™ menu.
2. Use the RIGHT 4-WAY Cursor Control key to initiate Cursor to
Waypoint.
3. Use the UP or DOWN 4-WAY Cursor Control key to highlight the
waypoint you wish to move the cursor to, then use the RIGHT 4-WAY
Cursor Control key to select the destination waypoint.
Waypoint Submenu
The Waypoint Submenu contains the following menu choices:
Edit allows you to edit the Name, Position (Latitude and Longitude) and
select the Icon that will be used to represent the waypoint in the Chart and
Combo Views.
Delete allows you to delete a waypoint from the list of saved waypoints.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Save Current Track
Save Current Route
(Only when navigating)
Save Current Track allows you to save the
current track being displayed. After the current track is saved, a new current
track is started.
Save Current Route allows you to save the current route being displayed.
This menu choice will only appear when you are currently navigating a route.
To Save Current Route:
To Save Current Track:
1. Highlight Save Current Route on the Navigation X-Press™ Menu.
1. Highlight Save Current Track on the Navigation X-Press™ Menu.
2. Use the RIGHT 4-WAY Cursor Control key to initiate saving the
current route.
2. Use the RIGHT 4-WAY Cursor Control key to initiate saving the
current track.
3. The Confirm dialog box will appear. To save the current route, press
the RIGHT Cursor key once more. To cancel saving the current route,
press the LEFT Cursor key.
3. The Confirm dialog box will appear. To save the current track, press
the RIGHT Cursor key once more. To cancel saving the current track,
press the LEFT Cursor key.
Skip Next Waypoint
(Only when navigating)
Clear Current Track
Clear Current Track allows you to clear the
current track being displayed and start a new track at the present position.
Skip Next Waypoint removes the next waypoint from the current route. This
menu choice will only appear when you are currently navigating a route.
To Skip Next Waypoint:
To Clear Current Track:
1. Highlight Skip Next Waypoint on the Navigation X-Press™ Menu.
1. Highlight Clear Current Track on the Navigation X-Press™ Menu.
2. Use the RIGHT 4-WAY Cursor Control key to initiate skipping the
next waypoint.
2. Use the RIGHT 4-WAY Cursor Control key to initiate clearing the
current track.
3. The Confirm dialog box will appear. To skip the next waypoint, press
the RIGHT Cursor key once more. To cancel skipping the next
waypoint, press the LEFT Cursor key.
3. The Confirm dialog box will appear. To clear the current track, press
the RIGHT Cursor key once more. To cancel clearing the current
track, press the LEFT Cursor key.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Cancel Navigation
(Only when navigating)
Remove Target
(Only if a Target is active)
Cancel Navigation discards the current route and exits Navigation Mode.
This menu choice will only appear when you are currently navigating a route.
This will not delete a previously-saved route.
Remove Target removes the waypoint target from the display. This menu
choice will only appear when a target has already been applied to a
waypoint.
To Cancel Navigation:
To Remove a Target:
1. Highlight Cancel Navigation on the Navigation X-Press™ Menu.
1. Highlight Remove Target on the Navigation X-Press™ Menu.
2. Use the RIGHT 4-WAY Cursor Control key to initiate canceling navigation.
2. Use the RIGHT 4-WAY Cursor Control key to remove the target.
3. The Confirm dialog box will appear. To cancel navigation, press the
RIGHT Cursor key once more. To avoid canceling navigation, press
the LEFT Cursor key.
Remove Grid
(Only if a Grid is active)
Cancel MOB Navigation
(only when MOB Navigation is activated)
Remove Grid removes the waypoint grid from the display. This menu choice
will only appear when a grid has already been applied to a waypoint.
Cancel MOB Navigation removes the Man Overboard (MOB) waypoint and
exits Man Overboard mode. This menu choice will only appear when you are
currently navigating in Man Overboard mode.
To Remove a Grid:
1. Highlight Remove Grid on the Navigation X-Press™ Menu.
2. Use the RIGHT 4-WAY Cursor Control key to remove the grid.
To Cancel MOB Navigation:
1. Highlight Cancel MOB Navigation on the Navigation X-Press™ menu.
2. Use the RIGHT 4-WAY Cursor Control key to initiate canceling MOB
navigation.
3. The Confirm dialog box will appear. To cancel MOB navigation, press
the RIGHT Cursor key once more. To avoid canceling MOB
navigation, press the LEFT Cursor key.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
The Waypoint Submenu contains the following menu choices:
Waypoint [Name]
(Most recently-created waypoint)
Edit allows you to edit the Name, Position (Latitude and Longitude) and
select the Icon that will be used to represent the waypoint in the Chart and
Combo Views.
Waypoint [Name] allows you to view the waypoints submenu for the most
recently created waypoint.
Delete allows you to delete a waypoint from the list of saved waypoints.
NOTE: You must have pressed the MARK key at least once since you last
powered up the Fishing System for this menu choice to appear.
Go To allows you to select a waypoint and start navigation toward that
waypoint, or add that waypoint to the end of the current route.
To view the Waypoint [Name] Submenu:
1. Move the cursor to the desired position and press the MARK key
once to save a waypoint.
Target allows you to apply a target to a waypoint selected from the list of
waypoints.
2. Highlight Waypoint[Name] on the Navigation X-Press™ menu.
Grid allows you to apply a trolling grid to a waypoint selected from the list
of waypoints.
3. Use the RIGHT 4-Way Cursor Control key to view the Waypoints
submenu.
Waypoint [Name] Submenu
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Snapshot and Recording
X-Press™ Menu
Start Recording
(optional-purchase MMC/SD Card, Snapshot and
Recording View only)
(Snapshot and Recording View only)
The Snapshot and Recording X-Press™
menu provides access to the image
management and sonar recording functions.
Press the MENU key once while in the
Snapshot and Recording View to access the
Snapshot and Recording X-Press™ menu.
Start Recording allows you to start sonar recording from the Snapshot and
Recording View. This menu option is only available when you have an
optional-purchase MMC/SD card installed and you are in Snapshot and
Recording View.
To start sonar recording:
1. Highlight Start Recording on the Snapshot and Recording X-Press™
menu, and press the RIGHT 4-Way Cursor key to start recording.
NOTE: For more information, see Snapshot and
Recording View.
Stop Recording
(optional-purchase MMC/SD Card only)
Snapshot and Recording
X-Press™ Menu
Stop Recording allows you to stop sonar recording. This menu option is only
available when you have an optional-purchase MMC/SD card installed.
To stop sonar recording:
1. To stop recording, highlight Stop Recording from any X-Press™
menu.
2. Press the RIGHT 4-Way Cursor key.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Delete Image
(optional-purchase MMC/SD Card, Snapshot and
Recording View only)
Delete All Images
(optional-purchase MMC/SD Card,
Snapshot and Recording View only)
Delete Image allows you to delete a single screen capture image from the
Snapshot and Recording View. This menu option is only available when you
have an optional-purchase MMC/SD card installed and you are in Snapshot
and Recording View and you have selected an image thumbnail.
Delete All Images allows you to delete all the images at once from the
Snapshot and Recording View. This menu option is only available when you
have an optional-purchase MMC/SD card installed and you are in Snapshot
and Recording View.
To delete an image:
To delete all images:
1. On the Screen Snapshot View, use the UP and DOWN 4-Way Cursor
keys to select the image you want to delete.
1. From the Snapshot and Recording View, highlight Delete All Images
on the Snapshot and Recording X-Press™ Menu.
2. Highlight Delete Image on the Snapshot and Recording X-Press™
menu.
2. A confirmation dialog box will ask if you want to delete all images.
Select Yes to delete, or No to change your mind.
3. Press the RIGHT 4-Way Cursor key to initiate this procedure.
4. A Confirm Dialog box will appear. Select Yes to delete the image or
No to cancel the operation.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Delete Recording
(optional-purchase MMC/SD Card,
Snapshot and Recording View only)
Delete All Recordings
(optional-purchase MMC/SD Card,
Snapshot and Recording View only)
Delete Recording allows you to delete a single sonar recording from the
Snapshot and Recording View. This menu option is only available when you
have an optional-purchase MMC/SD card installed, you are in Snapshot and
Recording View.
Delete All Recordings allows you to delete all the recordings at once from
the Snapshot and Recording View. This menu option is only available when
you have an optional-purchase MMC/SD card installed and you are in
Snapshot and Recording view.
To delete a recording:
To delete all recordings:
1. On the Snapshot and Recording View, use the UP and DOWN 4-Way
Cursor keys to highlight the recording you want to delete.
1. From the Snapshot and Recording View, highlight Delete All
Recordings on the Snapshot and Recording X-Press™ Menu.
2. A confirmation dialog box will ask if you want to delete all
recordings. Select Yes to delete, or No to change your mind.
2. Highlight Delete Recording on the Snapshot and Recording X-Press™
menu.
3. Press the RIGHT 4-Way Cursor key to initiate this procedure.
4. A Confirm Dialog box will appear. Select Yes to delete the recording
or No to cancel the operation.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Pings Per Second
(optional-purchase MMC/SD Card,
Snapshot and Recording View only)
Playback Speed
(optional-purchase MMC/SD Card,
Snapshot and Recording View only)
Pings Per Second allows you to specify the maximum ping rate for the sonar
recording currently in progress from the Snapshot and Recording View. This
menu option is only available when you have an optional-purchase MMC/SD
card installed and you are in Snapshot and Recording View and are actively
recording (not playing back).
Playback Speed allows you to specify the playback speed for a sonar
recording from the Snapshot and Recording View. This menu option is only
available when you have an optional-purchase MMC/SD card installed and
you are playing back a recording.
To specify playback speed:
To specify the pings per second:
1. Highlight Playback Speed on the Snapshot and Recording X-Press™
menu, and press the LEFT or RIGHT 4-Way Cursor key to display the
following Playback Speed submenu choices (which are represented
by icons): Beginning, Rewind2, Rewind, Reverse Normal, Reverse
Slow, Pause, Slow Play, Normal Play, FF, FF2, End.
1. Highlight Pings Per Second on the Snapshot and Recording X-
Press™ menu, and press the RIGHT 4-Way Cursor key to increase
and decrease the number in the menu bar. (1-AUTO, Default =
AUTO)
NOTE: You can also change playback speed in the Snapshot and Recording View
using the Left and Right 4-Way Cursor keys, although you cannot skip to the
beginning or end of a recording using these keys.
NOTE: Sonar chart speed is increased during Fast Forward and reversed during
Rewind. This may result in a reduced quality sonar image, since at higher speeds,
not every sonar return can be processed.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Stop Playback
Sonar Menu Tab
(optional-purchase MMC/SD Card only)
Press the MENU key twice to access the
Main Menu System and then press the
RIGHT Cursor key to select the Sonar tab.
Stop Playback allows you to stop playback of a sonar recording from any
view. This menu option is only available when you have an optional-
purchase MMC/SD card installed and you are playing back a recording.
NOTE: Menu choices will vary depending on
system settings such as whether the unit is set
for Advanced User mode or what transducer is
currently selected.
To stop playback of a recording:
1. Highlight Stop Playback on any X-Press™ menu.
2. Press the RIGHT 4-Way Cursor key to initiate this procedure.
To start playback, use the 4-Way Cursor keys to highlight a recording
icon, then press the RIGHT 4-Way Cursor key to start playback
(represented by a green "play" triangle which appears to the right of
the recording icon).
NOTE: During playback, the amount of time/memory left to play is indicated by
the status bar. For more information, see Snapshot and Recording View.
Sonar Menu
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Beam Select
Fish ID+™
Beam Select sets which sonar returns from
the transducer will be displayed on the screen.
Fish ID+™ uses advanced signal processing
to interpret sonar returns, and will display a Fish Symbol when very selective
requirements are met. When a fish is detected, a fish icon and its depth are
displayed above the return that has been classified as being a fish. Three
different fish size icons represent the intensity of the sonar return, and
provide an indicator of relative fish size.
When set to 200/83 kHz, the returns from both beams are blended. The Split
Sonar View continues to display the sonar returns from each beam in their
respective windows. The blended information is shown in the Sonar View.
The RTS® Window in the Sonar View will only show the returns from the
200 kHz narrow beam.
DualBeam PLUS™ sonar models represent targets detected in the 200 kHz
narrow beam as orange fish symbols, and represent targets detected in the
83 kHz wide beam as blue fish symbols.
When set to 200 kHz, only the returns from the 200 kHz narrow beam will
be displayed in the Sonar View. The Split Sonar View will continue to display
returns from both beams in their respective windows. The RTS® Window in
the Sonar View will display the returns from the 200 kHz narrow beam.
83 kHz, wide beam blue fish symbols
200 kHz, narrow beam
orange fish symbols
When set to 83 kHz, the returns from the 83 kHz wide beam will be
displayed in the Sonar View. The Split Sonar View will continue to display
returns from both beams in their respective windows. The RTS® Window will
display the returns from the 83 kHz wide beam.
When Fish ID+™ is turned off, the 900 Series™ shows only the raw sonar
returns on the display. These returns will often result in "arches" forming on
the display, indicating potential targets. Due to the transducer beam angle,
the distance to a fish decreases as the fish moves into the beam, and then
increases as it moves out again, creating a Fish Arch when this distance
change is shown on the display. Boat speed, chart speed, and the position
of the fish within the sonar beam greatly affect the shape of the arch.
To use Beam Select:
1. Highlight Beam Select on the Sonar main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to select either
the 200 kHz beam, the 83 kHz beam or the 200/83 kHz beam.
(200/83 kHz, 200 kHz, 83 kHz, Default = 200 kHz)
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Fish ID Sensitivity
Fish ID Sensitivity adjusts the threshold of
the Fish ID+™ detection algorithms. Selecting a higher setting allows
weaker returns to be displayed as fish. This is useful for identifying smaller
fish species or baitfish. Selecting a lower setting displays fewer fish from
weak sonar returns. This is helpful when seeking larger species of fish. Fish
Sensitivity is used in conjunction with Fish ID+™. Fish ID+™ must be On for
Fish Sensitivity to affect the ability of the 900 Series™ to identify sonar
returns as fish.
Transducer Cone and Fish Arches
To change the Fish ID Sensitivity setting:
1. Highlight Fish ID Sensitivity on the Sonar main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Fish
Sensitivity setting. (Low = 1, High = 10, Default = 5)
To turn Fish ID+™ on or off:
1. Highlight Fish ID+ on the Sonar main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to turn the Fish
ID+™ setting On or Off. (Off, On, Default = Off)
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Real Time Sonar (RTS®) Window
Bottom View
RTS® Window sets the RTS® Window to
either Wide or Narrow, or turns it off in the Sonar View. The RTS® Window
always updates at the fastest rate possible and only displays returns that are
within the transducer beam. (See Getting Started - Using Your 900
Series™: Real Time Sonar [RTS®] Window for more information.)
Bottom View selects the method used to
represent bottom and structure on the display. Structure ID® represents
weak returns in blue and strong returns in red. WhiteLine® highlights the
strongest sonar returns in white resulting in a distinctive outline. This has
the benefit of clearly defining the bottom on the display. See Bottom
Presentation for more information.
To change the RTS® Window setting:
To adjust the Bottom View:
1. Highlight RTS® Window on the Sonar
main menu.
1. Highlight Bottom View on the Sonar Main Menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
Bottom View setting. (Structure ID, WhiteLine, Default = Structure ID)
2. Use the LEFT or RIGHT 4-WAY Cursor
Control keys to change the RTS® Window
setting. (Wide, Narrow, Off, Default =
Narrow)
RTS® Window (Wide)
RTS® Window (Narrow)
RTS® Window (Off)
Zoom Width
(Sonar Zoom View only)
Zoom Width allows you to control the width of the Zoomed Sonar (the left-
hand side of the screen).
To change the Zoom Width:
1. Highlight Zoom Width on the Sonar Main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
width of the Zoomed Sonar. (Narrow, Medium, Wide, Default =
Narrow)
82
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: The 455 kHz Sensitivity requires the purchase of the QuadraBeam PLUS™
transducer.
83 kHz Sensitivity
(Advanced)
83 kHz Sensitivity changes the sensitivity of the 83 kHz beam. Increasing the
83 kHz Sensitivity will display additional weak returns and decreasing the 83
kHz Sensitivity will display fewer weak returns. The 83 kHz Sensitivity menu
choice is only available when User Mode is set to Advanced (see Setup
Menu Tab: User Mode).
You can visit our website at www.humminbird.com to order this accessory
online or contact our Customer Resource Center at 1-800-633-1468.
NOTE: 455 kHz Sensitivity is particularly useful for adjusting the sensitivity of the
455 kHz sonar returns in the Side Beam View. The 455 kHz sensitivity can be
adjusted without affecting the sensitivity of the 200 kHz returns shown in the
200 kHz sonar window.
To set the 83 kHz Sensitivity:
1. Make sure you are in Advanced User Mode, then highlight 83 kHz
Sensitivity on the Sonar main menu.
To change the 455 kHz Sensitivity setting:
1. Make sure you have selected QuadraBeam Transducer and Advanced
Mode and that the QuadraBeam PLUS™ transducer is connected, then
highlight 455 kHz Sensitivity on the Sonar Main Menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to set the 83 kHz
Sensitivity. (-10 to +10, Default = 0)
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
455 kHz Sensitivity. (-10 to +10, Default = 0)
455 kHz Sensitivity
(Advanced, with QuadraBeam PLUS™ transducer,
optional-purchase for the 917)
455 kHz Sensitivity adjusts the sensitivity of the 455 kHz beam. Increasing
the sensitivity will display additional weak returns and decreasing the
sensitivity will display fewer weak returns. A QuadraBeam PLUS™
transducer must be attached to the Fishing System (included on the 957 and
optional-purchase on the 917). The 455 kHz Sensitivity menu choice is
available when Transducer Select is set to QuadraBeam (see Sonar Menu
Tab: Transducer Select) and User Mode is set to Advanced (see Setup
Menu Tab: User Mode).
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Depth Lines
(Advanced)
Surface Clutter
(Advanced)
Depth Lines divide the display into four equal sections that are separated by
three horizontal depth lines. The depth of each line is displayed along the
depth scale. You can either turn Depth Lines On or Off. The Depth Lines
menu choice is available when User Mode is set to Advanced (see Setup
Menu Tab: User Mode).
Surface Clutter adjusts the filter that removes surface clutter noise caused
by algae and aeration. The lower the setting, the less surface clutter will be
displayed. The Surface Clutter menu choice is available when User Mode is
set to Advanced (see Setup Menu Tab: User Mode).
Surface Clutter
Depth Lines
To change the Surface Clutter setting:
To change the Depth Lines setting:
1. Make sure you are in Advanced User Mode, then highlight Surface
Clutter on the Sonar main menu.
1. Make sure you are in Advanced User Mode, then highlight Depth Lines
on the Sonar main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
Surface Clutter setting. (Low = 1 to High = 10, Default = 5)
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to turn the Depth
Lines setting On or Off. (Off, On, Default = On)
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Noise Filter
(Advanced)
Max Depth
(Advanced)
Noise Filter adjusts the sonar Noise Filter to limit interference on the display
from sources such as your boat engine, turbulence, or other sonar devices.
The Noise Filter menu choice is available when User Mode is set to
Advanced (see Setup Menu Tab: User Mode).
Max Depth adjusts the maximum depth of operation. The performance of
your 900 Series™ can be tuned to the maximum depth you will be fishing in
by setting the Max Depth. When a maximum depth is set, your 900 Series™
will not attempt to acquire sonar data below that depth, thus increasing
overall performance. When Max Depth is set to Auto, the 900 Series™ will
acquire bottom readings as needed (within the capacity of the unit).
If the bottom is deeper than the Max Depth setting, the digital depth readout
will flash, indicating that the 900 Series™ cannot locate the bottom. The
Max Depth menu choice is available when User Mode is set to Advanced
(see Setup Menu Tab: User Mode).
NOTE: The Off setting removes all filtering; Low, Medium and High settings add
progressive filtering of the sonar returns. In some deep water situations, the High
setting may actually make it harder for the control head to find the bottom.
To change the Noise Filter setting:
1. Make sure you are in Advanced User Mode, then highlight Noise
Filter on the Sonar main menu.
To change the Max Depth setting:
1. Make sure you are in Advanced User Mode, then highlight Max
Depth on the Sonar main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change
the Noise Filter setting. (Off, Low, Medium, High 1, High 2, High 3,
Default = Low)
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
Max Depth setting. (AUTO, 10 to 1500 feet; 3 to 500 meters
[International models only], Default = AUTO)
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Water Type
(Advanced)
Transducer Select
Transducer Select allows you to select
which transducer you want to use.
Water Type configures your unit for operation in fresh or salt water. The
Water Type menu choice is available when User Mode is set to Advanced
(see Setup Menu Tab: User Mode).
NOTE: The transducer setting must correspond to the transducer type connected
to your system.
NOTE: In salt water, what would be considered a large fish might be 2 to 10
times bigger than a large fish in fresh water (depending on the type of fish you
are seeking). The salt water setting allows for a greater range in fish size
adjustment to account for this. Also, make sure that the Water Type is set
accurately, especially in salt water, as this affects the accuracy of deep water
depth readings.
NOTE: The QuadraBeam PLUS™ transducer is standard on the 957c Combo, but
is optional-purchase only for the 917c Combo.
To change the selected Transducer:
1. Highlight Transducer Select on the Sonar Main menu.
To change the Water Type setting:
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
transducer selected. (917c Combo: Quad Beam, Dual Beam, Universal
Sonar 2, Default = Dual Beam; 957c Combo: Quad Beam, Dual Beam,
Dual 50/200, Universal Sonar 2, Default = Quad Beam)
1. Make sure you are in Advanced User Mode, then highlight Water
Type on the Sonar main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
Water Type setting. (Fresh, Salt, Default = Fresh)
Color Bar
Color Bar allows you to display or suppress
the display of the color bar shown in the full screen Sonar View.
To change the display of the Color Bar:
1. Highlight Color Bar on the Sonar Main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
display of the color bar. (Off, On, Default = On)
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Temperature Graph
Navigation Menu Tab
(Sonar View only, with Temperature input)
Press the MENU key twice to access the
Main Menu System, then press the RIGHT
cursor key to select the Navigation tab.
Temperature Graph allows you to display or suppress a water temperature
graph over the main Sonar View to show temperature changes correlated to
recent sonar history.
NOTE: Menu choices will vary depending on
system settings.
To change the display of the Temperature Graph:
1. In the Sonar View, highlight Temperature Graph on the Sonar main
menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
display of water temperature. (Off, On, Default = On)
Navigation Menu
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Current Track
Saved Tracks
Current Track allows you to view the Current
Saved Tracks allows you to view the Saved
Track submenu.
Tracks submenu.
To view the Current Track Submenu:
To view the Saved Tracks Submenu:
1. Highlight Current Track on the Navigation main menu.
1. Highlight Saved Tracks on the Navigation main menu.
2. Use the RIGHT 4-WAY Cursor Control keys to view the Current Track
submenu.
2. Use the RIGHT 4-WAY Cursor Control keys to view the Saved Tracks
submenu.
Current Track Submenu
Saved Tracks Submenu
The Current Track Submenu contains the following menu choices:
Save Current Track allows you to save the current track.
Clear Current Track allows you to clear the current track.
The Saved Tracks Submenu contains the following menu choices:
Edit allows you to select a previously-saved track and edit its name, whether
it is visible or not, and its appearance.
Delete allows you to delete a track from a list of previously-saved tracks.
Appearance allows you to change the style and color of the current track.
(Breadcrumb Trail, Dashed Line, Solid Line or Wide Line, and if a line, the color
of the line, or Color By Depth. If you choose Color By Depth, you cannot choose
one color to represent the track; a color range will represent the different
depths on the track instead, from light green (shallowest) to black (deepest).
You can change the depth range associated with black by using Track Color
Range menu setting (see Navigation Main Menu: Track Color Range).
Default sets the appearance of the track created by selecting Save Current
Track.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
Delete allows you to delete a waypoint from the list of saved waypoints.
Waypoints
Cursor To allows you to move the cursor quickly to a waypoint selected from
the list of saved waypoints.
Waypoints allows you to view the Waypoints
submenu.
Go To allows you to select a waypoint and start navigation toward that
waypoint, or add that waypoint to the end of the current route.
To view the Waypoints Submenu:
1. Highlight Waypoints on the Navigation main menu.
Target allows you to apply a target to a waypoint selected from the list of
waypoints.
2. Use the RIGHT 4-WAY Cursor Control keys to view the Waypoints
submenu.
Grid allows you to apply a trolling grid to a waypoint selected from the list
of waypoints.
Routes
Routes allows you to view the Routes submenu.
To view the Routes Submenu:
1. Highlight Routes on the Navigation main menu.
Waypoints Submenu
2. Use the RIGHT 4-WAY Cursor Control keys to view the Routes
submenu.
The Waypoints Submenu contains the following menu choices:
Create allows you to create a new waypoint and edit it immediately. The
current boat position will be used as the default, but you can set the
coordinates to any valid position. The Icon used to represent the waypoint in
the Chart and Combo Views can also be changed.
Edit allows you to choose from a list of previously-saved waypoints, then edit
the Name, Position (Latitude and Longitude) and select the Icon that will be
used to represent the waypoint in the Chart and Combo Views.
Routes Submenu
89
Download from Www.Somanuals.com. All Manuals Search And Download.
The Routes Submenu contains the following menu choices:
Chart Orientation
Create allows you to create a new, empty route and add waypoints to it
immediately.
Chart Orientation allows you to select
whether the views containing charts should be drawn North-Up or Course-Up.
Edit allows you to select a previously-saved route and edit its name and the
waypoints on it.
To change the Chart Orientation setting:
1. Highlight Chart Orientation on the Navigation main menu.
Delete allows you to delete a route from a list of previously-saved routes.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Chart
Orientation setting. (North-Up, Course-Up, Default = North-Up)
Travel allows you to select a previously-saved route to use as the current
route; this menu setting also begins navigation on this route. Routes can be
traveled in either the forward or reverse direction.
NOTE: The Chart Orientation setting does not apply to the Bird's Eye View.
Info displays information about the route, including the distance and
bearing from each waypoint to the next.
North Reference
North Reference allows you to have bearings
displayed with one of two orientations: True North or Magnetic North.
To change the North Reference setting:
1. Highlight North Reference on the Navigation main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
North Reference setting. (True, Magnetic, Default = True)
90
Download from Www.Somanuals.com. All Manuals Search And Download.
Trolling Grid Rotation
Track Min Distance
(Advanced)
Trolling Grid Rotation allows you to set the
orientation of the trolling grid in degrees, where a setting of 0° displays a
standard North, South, East, West alignment. See Waypoints for information
on how to set a Grid.
Track Min Distance allows you to set a minimum distance of travel before a
trackpoint is added to the track.
NOTE: Track Min Distance works in conjunction with Trackpoint Interval. Both
conditions must be met before a trackpoint is added to the current track.
To change the Trolling Grid Rotation setting:
1. Highlight Trolling Grid Rotation on the Navigation main menu.
To change the Track Minimum Distance setting:
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
Trolling Grid Rotation setting. (0° to 89°, Default = 0°)
1. Make sure you are in Advanced User Mode, then highlight Track
Min Distance on the Navigation main menu.
Trackpoint Interval
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
Track Min Distance setting. (1 to 300 feet or 1 to 100 meters
[International Units only], Default = 16 ft, 5 m)
Trackpoint Interval allows you to select the
time period between trackpoints. The current track can only contain up to
20,000 trackpoints, so longer time periods cause the track to extend back
further in time, but will be less detailed.
NOTE: During slow travel or drift, setting both Trackpoint Interval and Track Min
Distance to small values will allow you to increase the track resolution.
NOTE: Trackpoint Interval works in conjunction with Track Min Distance. Both
conditions must be met before a trackpoint is added to the current track.
To change the Trackpoint Interval setting:
1. Highlight Trackpoint Interval on the Navigation main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
Trackpoint Interval setting. (1 second, 5 seconds, 10 seconds, 15
seconds, 30 seconds or 60 seconds, Default = 1 second)
NOTE: During slow travel or drift, setting both Trackpoint Interval and Track Min
Distance to small values will allow you to increase the track resolution.
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Track Color Range
Course Projection Line
Track Color Range allows you to set the depth
range that will be displayed as black, the deepest depth, when Color By
Depth is selected as the style for the current track (see Navigation Menu
Tab: Current Track).
Course Projection Line allows you to display
or hide an arrow extending from the bow of the boat that projects your
current course, and shows where the boat will go if you continue on your
present course.
NOTE: Only an optional-purchase transducer with a 50 kHz frequency will allow
you to track to 3,000 feet.
To change the Course Project Line setting:
1. Highlight Course Projection Line on the Navigation main menu.
To change the Track Color Range:
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
Course Projection Line setting (Hidden, Visible, Default = Visible)
1. Highlight Track Color Range on the Navigation main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
Track Color Range setting. (50 to 3000 feet or 20 to 1000 meters
[International Units only], Default = 50 ft, 20 m)
Export All Nav Data
(Advanced)
Export All Nav Data allows you to export all saved Tracks, Waypoints and
Routes to an MMC/SD card.
Map Datum
(Advanced)
To Export All Navigation Data:
Map Datum allows you to change the map coordinate system used by the
900 Series™ to match those of a paper map.
1. Make sure you are in Advanced User Mode, and that an optional-
purchase MMC/SD card is installed in the slot, then highlight Export
All Nav Data on the Navigation main menu.
To change the Map Datum setting:
1. Make sure you are in Advanced User Mode, then highlight Map
Datum on the Navigation main menu.
2. Use the RIGHT 4-WAY Cursor Control key to export all navigation
data.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
Map Datum setting. (Default = WGS 84)
92
Download from Www.Somanuals.com. All Manuals Search And Download.
Delete All Nav Data
Chart Menu Tab
(Advanced)
Press the MENU key twice to access the
Main Menu System and then press the
RIGHT Cursor key to select the Chart tab.
Delete All Nav Data allows you to delete all saved Tracks, Waypoints and
Routes. This menu choice should be used with caution.
NOTE: Menu choices will vary depending on
system settings such as whether the unit is set
for Advanced User mode.
To Delete All Navigation Data:
1. Make sure you are in Advanced User Mode, then highlight Delete
All Nav Data on the Navigation main menu.
2. Use the RIGHT 4-WAY Cursor Control key to delete all navigation
data.
Continuous Navigation Mode
Chart Menu
Continuous Navigation Mode allows you to
continue to navigate and fish around a particular waypoint, even if you pass
over it multiple times.
To activate or de-activate Continuous Navigation:
1. Highlight Continuous Navigation Mode on the Navigation main
menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to turn
Continuous Navigation Mode On or Off (Off, On, Default = Off)
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Chart Detail Level
Map Borders
Chart Detail Level allows you to select how
much chart detail you want displayed on the Navigation Views. Basic shows
land areas, ports, obstructions and restricted areas. Navigation shows
navaids, landmarks, ferryways and navigation routes in addition to the Basic
information. Underwater shows depth contours, fishing areas, underwater
wrecks, tides and currents in addition to the Basic and Navigation
information. All shows roads, buildings, railways, and other notations in
addition to the Basic, Navigation and Underwater information.
Map Borders allows you to display or hide
map borders. A Map Border indicates an area which contains a different map.
Map Borders, shown with
Optional-Purchase Navionics® Cartography
To change the Chart Detail Level setting:
1. Highlight Chart Detail Level on the Navigation main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
Chart Detail Level setting. (Basic, Navigation, Underwater, All,
Default = All)
NOTE: Some chart details are only available with optional-purchase MMC/SD
cards.
Map Borders
To change the Map Borders setting:
1. Highlight Map Borders on the Navigation main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change
the Map Borders setting. (Hidden, MMC/SD Only, All Visible,
Default = MMC/SD Only)
94
Download from Www.Somanuals.com. All Manuals Search And Download.
Lat/Lon Grid
Navaids on Bird's Eye View
Lat/Lon Grid allows you to display or hide a
grid showing latitude and longitude lines.
Navaids on Bird's Eye View allows you to
display or hide additional navigational aids, such as lights and buoys, in
Bird's Eye View.
To change the Lat/Lon Grid setting:
NOTE: You will see more navigational aids with and optional-purchase
MMC/SD card.
1. Highlight Lat/Lon Grid on the Navigation main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
Lat/Lon Grid setting. (Hidden, Visible, Default = Hidden)
To change the Navaids on Bird's Eye View setting:
1. Highlight Navaids on Bird's Eye View on the Chart main menu.
Spot Soundings
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
Navaids on Bird's Eye View setting. (Hidden, Visible, Default =
Visible)
Spot Soundings allows you to display or
hide spot soundings, which are depth measurements shown on the chart.
NOTE: Spot Soundings are only available with optional-purchase MMC/SD cards.
Shaded Depth
To change the Spot Soundings setting:
Shaded Depth allows you to change the
depth used for shading on the chart views.
1. Highlight Spot Soundings on the Navigation main menu.
To change the Shaded Depth setting:
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
Spot Soundings setting. (Hidden, Visible, Default = Hidden)
1. Highlight Shaded Depth on the Navigation main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
Shaded Depth setting. (Off, 1 to 60 Feet or 1 to 20 Meters
[International Units only], Default = 15 ft, 5 m)
95
Download from Www.Somanuals.com. All Manuals Search And Download.
z
Set Simulation Position
(Advanced)
Set Map Offset
(Advanced)
Set Simulation Position allows you to set the position of the boat used in
Set Map Offset allows you to change the map offset used by the 900 Series™.
the Simulator.
NOTE: The Map Offset will be applied to all maps and not just the map that
requires the correction. The Map Offset should be cleared if a different map is to
be used.
To set the Simulation Position:
1. Activate the cursor and move it to the coordinates from where you
want simulation to start.
To change the Map Offset setting:
1. Activate the cursor and move it location where the Map Offset will
be applied.
NOTE: The cursor must be active in order for this procedure to work.
2. Make sure you are in Advanced User Mode, then highlight Set
Simulation Position on the Navigation main menu.
NOTE: The cursor must be active in order for this procedure to work.
2. Make sure you are in Advanced User Mode, then highlight Set Map
Offset on the Navigation main menu.
3. Use the RIGHT 4-WAY Cursor Control key to change the Simulation
Position setting. A confirmation dialog box will appear to allow you
to change your mind, or to confirm your choice. If the cursor was not
active before you began this procedure, you will see an error
message. Exit the menu, set the cursor, then try again.
3. Use the RIGHT 4-WAY Cursor Control key to set the Map Offset. A
confirmation dialog box will appear to allow you to change your
mind, or to confirm your choice. If the cursor was not active before
you began this procedure, you will see an error message. Exit the
menu, set the cursor, then try again.
96
Download from Www.Somanuals.com. All Manuals Search And Download.
Clear Map Offset
Alarms Menu Tab
(Advanced)
From any view, press the MENU key twice to
access the Main Menu System. The Alarms
tab will be the default selection.
Clear Map Offset allows you to clear the Map Offset. Clear Map Offset is
only accessible if a Map Offset is currently active.
NOTE: When an alarm is triggered, you can
silence it by pressing any key. The alarm will be
silenced, and will not be triggered again until a
new instance of the alarm condition is detected.
To Clear Map Offset:
1. Make sure you are in Advanced User Mode, then highlight Clear
Map Offset on the Navigation main menu.
2. Use the RIGHT 4-WAY Cursor Control key to clear the Map Offset.
Alarms Menu
97
Download from Www.Somanuals.com. All Manuals Search And Download.
To change the Fish ID Alarm setting:
Depth Alarm
1. Highlight Fish ID Alarm on the Alarms main menu.
Depth Alarm sounds when the depth
becomes equal to or less than the menu setting.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Fish
ID Alarm setting. (Off, All, Large/Medium, Large, Default = Off)
To change the Depth Alarm setting:
1. Highlight Depth Alarm on the Alarms main menu.
Low Battery Alarm
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
Depth Alarm setting. (OFF, 1 to 100 feet, or 0.5 to 30 meters
[International models only], Default = OFF)
Low Battery Alarm sounds when the input
battery voltage is equal to or less than the menu setting. The battery alarm
will only sound for the battery that is connected to the 900 Series™. The Low
Battery Alarm should be set to warn you when the battery voltage drops
below the safety margin that you have determined. For instance, if you are
running a trolling motor (battery operated), you would want to set the Low
Battery Alarm to sound before the battery voltage drops too low for it to be
used to start your main, gasoline-powered engine.
Fish ID Alarm
Fish ID Alarm sounds when the
900 Series™ detects fish that correspond to the alarm setting. Fish ID Alarm
will only sound if Fish ID+™ is on.
To change the Low Battery Alarm setting:
1. Highlight Low Battery Alarm on the Alarms main menu.
For example, if you've set the Fish ID Alarm to sound for Large fish
only, the Fish ID alarm will sound when a large-sized fish is detected.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
Low Battery Alarm setting. (Off, 8.5V - 13.5V, Default = Off)
Off
All
Large/Medium
Large
98
Download from Www.Somanuals.com. All Manuals Search And Download.
Aux Temp Alarm
(with optional-purchase temp. probe or Temp/Speed only)
Temp Alarm
Temp Alarm sounds when the water
temperature detected by the 900 Series™ reaches the Temp Alarm setting,
which is either set in degrees Fahrenheit or Celsius [International models
only]. For example, if the Temp Alarm is set to 58° Fahrenheit, and the water
temperature falls from 60° to 58°, the Temp Alarm will sound. Similarly, if the
water temperature rises from 56° to 58°, the Temp Alarm will also sound.
Aux Temp Alarm sounds when the water temperature from the
Paddlewheel/Temperature Probe detected by the Fishing System reaches the
Aux Temp Alarm setting, which is either set in degrees Fahrenheit or Celsius
[International Models only]. For example, if the Aux Temp Alarm is set to 58
degrees Fahrenheit, and the water temperature falls from 60 degrees to 58
degrees, the Aux Temp Alarm will sound. Similarly, if the water temperature
rises from 56 degrees to 58 degrees, the Temp Alarm will also sound.
To change the Temp Alarm setting:
1. Highlight Temp Alarm on the Alarms main menu.
To change the Aux Temp Alarm setting:
2. Use the LEFT or RIGHT 4-Way Cursor Control keys to change the
Temp Alarm setting. (Off, 32-120 [Fahrenheit], 0-50 [Celsius
(International models only)], Default = Off)
1. Highlight Aux Temp Alarm on the Alarms main menu.
2. Use the LEFT or RIGHT 4-Way Cursor Control keys to change the
Aux Temp Alarm setting. (Off, 33-120 [Fahrenheit], 0-50 [Celsius],
Default = Off)
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Off Course Alarm
Arrival Alarm
Off Course Alarm sounds when the boat
has moved too far off course based on the menu setting when navigating.
Off Course Alarm allows you to set how far the boat is allowed to move off
course before the Off Course Alarm will sound.
Arrival Alarm sounds when the boat has
either exceeded the distance to the destination waypoint, or has entered the
Arrival Alarm Circle, based on the menu setting when navigating. Arrival
Alarm allows you to set how close the boat must be to the destination
waypoint before the Arrival Alarm will sound.
Off Course Alarm
To change the Arrival Alarm setting:
1. Highlight Arrival Alarm on the Alarms main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
Arrival Alarm setting. (Off, 25 to 3000 feet, 10 to 1000 meters
[International models only], Default = 150 ft, 50 m)
1
11
2
Arrival Alarm Circle
Off Course Limits
1
2
To change the Off Course Alarm setting:
1. Highlight Off Course Alarm on the Alarms main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Off
Course Alarm setting. (Off, 25 to 3000 feet, 10 to 1000 meters
[International models only], Default = 300 ft, 100 m)
100
Download from Www.Somanuals.com. All Manuals Search And Download.
Drift Alarm
Alarm Tone
Drift Alarm sounds when the boat has
exceeded the distance from the boat’s anchored position, based on the
menu setting. Drift Alarm allows you to set the size of a perimeter around the
boat’s anchored position; if the anchored boat drifts outside of that
perimeter, the Drift Alarm will sound.
Alarm Tone selects the pitch of the alarm
sound. A brief tone will be produced as you adjust the Alarm Tone so that
you can select the tone that you can hear best.
To change the Alarm Tone setting:
1. Highlight Alarm Tone on the Alarms main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
Alarm Tone setting. (High, Medium, Low, Default = Medium)
Drift Alarm Circle
To change the Drift Alarm setting:
1. Highlight Drift Alarm on the Alarms main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
Drift Alarm setting. (Off, 25 to 3000 feet, 10 to 1000 meters
[International models only], Default = Off)
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menu Tab
Units - Depth
From any view, press the MENU key twice to
access the tabbed Main Menu System, then
press the RIGHT cursor key until the Setup
tab is selected.
Units - Depth selects the units of measure
for all depth-related readouts.
To change the Units - Depth setting:
1. Highlight Units - Depth on the Setup menu.
NOTE: Menu choices will vary depending on
system settings such as whether the unit is set
for Advanced User mode and what accessories
are attached to the control head.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
Units - Depth setting. (Meters [International models only], Feet,
Fathoms; Default is Meters for International models, and Feet for
Domestic models)
Units - Temp
(International only)
Units - Temp selects the units of measure for all temperature-related
readouts. International models only.
To change the Units - Temp setting:
1. Highlight Units - Temp on the Setup menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
Units - Temp setting. (Celsius, Fahrenheit; Default = Celsius)
Setup Menu
102
Download from Www.Somanuals.com. All Manuals Search And Download.
Units - Distance
(with Speed input only)
User Mode
User Mode sets the menu system to either
Normal or Advanced. When set to Normal, only the basic menu options are
shown. When set to Advanced (default setting), additional menu choices
are available.
Units - Distance selects the units of measure for all distance-related
readouts.
To change the Units - Distance setting:
To change the User Mode setting:
1. Highlight Units - Distance on the Setup menu.
1. Highlight User Mode on the Setup menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
Units - Distance setting. (Domestic Models: Statute Miles, Nautical
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
User Mode setting. (Normal, Advanced, Default = Advanced)
Miles; Default
=
Statute Miles; International Models:
Meters/Kilometers, Meters/Nautical Miles, Feet/Statute Miles,
Feet/Nautical Miles; Default = Meters/Kilometers)
Language
(International only)
Units - Speed
(with Speed input only)
Language selects the display language for menus. International models only.
To change the Language setting:
Units - Speed selects the units of measure for speed-related readouts.
1. Highlight Language on the Setup menu.
To change the Units - Speed setting:
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
Language setting. (Default = English)
1. Highlight Units - Speed on the Setup menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Units -
Speed setting. (kph [International models only], mph, kts, Default =
kph for International models and mph for Domestic models)
103
Download from Www.Somanuals.com. All Manuals Search And Download.
Triplog Reset
Select
(with Speed input only)
Readouts
(Advanced)
Triplog Reset resets the Triplog to zero. The Triplog provides the following
information: timer for elapsed time, distance traveled since last reset, and
average speed.
Select Readouts allows you to customize the
information displayed in individual digital readouts on
the left side of many views, including suppressing a
particular readout so that nothing is displayed; the
ability to customize readouts depends on the view
and whether you are navigating. This Advanced
feature allows you to select what data will be
displayed in each of 5 fixed-position data windows
arranged at the left edge of the Sonar View screen, or
whether a particular data window will be turned off,
displaying nothing in that area; you can access this
menu choice only when in Advanced User Mode (see
Setup Menu Tab: User Mode.)
To Reset Triplog:
1. Highlight Reset Triplog on the Setup menu.
2. Use the RIGHT 4-WAY Cursor Control key to initiate Triplog Reset.
3. The Confirm dialog box will appear. To reset the Triplog, press the
RIGHT Cursor key once more. To cancel Reset Triplog, press the LEFT
Cursor key.
Select Readouts
Restore Defaults
Restore Defaults resets ALL menu settings
to their factory defaults. Use this menu choice with caution!
Data windows can display readouts from supported accessories such as a
Speed accessory. Each data window can either be empty (Off) or contain one
of the following:
To Restore Defaults:
• Course
• Depth
• Time
1. Highlight Restore Defaults on the Setup menu.
• Time + Date
• Triplog
2. Use the RIGHT 4-WAY Cursor Control key to initiate restoring
defaults.
• Off
• Position
• Aux. Temperature
• Speed
• Voltage
3. The Confirm dialog box will appear. To reset the defaults, press the
RIGHT Cursor key once more. To cancel Restore Defaults, press the
LEFT Cursor key.
• Temperature
• Water Speed
104
Download from Www.Somanuals.com. All Manuals Search And Download.
Sonar-only Views, Not Navigating: On Sonar-only views, as long as you are
not navigating, all 5 readouts are customizable.
Other Views, Not Navigating: On any view with a chart, as long as you are
not navigating, two of the readouts are not customizable: the 2nd box
always displays Heading, while the 5th box always displays Speed. On the
Bird’s Eye View, when you are not navigating, there are four fixed info boxes
that show Depth, Heading, Position (Lat/Lon) and Speed. When you are
navigating in the Bird's Eye View, there are two columns of four boxes. The
first column shows Depth, Time To Go (TTG), Position (Lat/Lon), and Speed.
The second column shows Cross Track Error (XTE), Heading, Bearing, and
Distance To Go (DTG).
Default Sonar View
All Views, Navigating: When you are navigating, all readouts in all views
(even split screen views with a Sonar display) cannot be customized, with
the exception of the top readout info box, which is still customizable. In any
view, while you are navigating, the second readout box shows Heading, the
third box shows Bearing, the fourth box is divided to show Cross Track Error
(XTE) and Distance To Go (DTG), and the fifth box is divided to show Time To
Go (TTG) and Speed.
Customized Sonar View
105
Download from Www.Somanuals.com. All Manuals Search And Download.
To Select Readouts:
Aux Temp Offset
(Advanced)
1. Make sure you are in Advanced User Mode, then highlight Select
Readouts on the Setup main menu.
Aux Temp Offset will adjust the aux temperature readout (the temperature
on the optional-purchase temperature probe or Temp/Speed accessory) by
the amount entered. This menu choice is available only when in Advanced
User Mode (see Setup Menu Tab: User Mode.)
2. Use the RIGHT 4-WAY Cursor Control key to initiate this procedure.
3. The Select Readouts submenu will appear, showing a list of all
Readouts. Use the UP or DOWN Cursor keys to select a particular
Readout position, then use the RIGHT or LEFT Cursor keys to change
what will be displayed at that position. (Aux. Temperature, Course,
Depth, Off, Position, Speed, Temperature, Time, Time+Date, Triplog,
Voltage, Water Speed)
To change the Aux Temp Offset setting:
1. Make sure you are in Advanced User Mode, then highlight Aux
Temp Offset on the Setup menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Aux
Temp Offset setting. (-10.0 to +10.0 degrees, Default = 0)
Depth Offset
(Advanced)
Temp Offset
Depth Offset will adjust the digital depth readout to indicate depth from the
waterline or boats keel. Enter a positive vertical measurement from the
transducer to the waterline to read the depth from the waterline. Enter a
negative vertical measurement from the transducer to keel to read the depth
from the keel. This menu choice is available only when in Advanced User
Mode (see Setup Menu Tab: User Mode.)
(Advanced)
Temp Offset will adjust the temperature readout by the amount entered.
This menu choice is available only when in Advanced User Mode (see Setup
Menu Tab: User Mode.)
To change the Temp Offset setting:
To change the Depth Offset setting:
1. Make sure you are in Advanced User Mode, then highlight Temp
Offset on the Setup menu.
1. Make sure you are in Advanced User Mode, then highlight Depth
Offset on the Setup menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
Temp Offset setting. (-10.0 to +10.0 degrees, Default = 0.0, or Off)
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change
the Depth Offset setting. (-10.0 to +10.0 feet or -3 to 3 meters
[International models only], Default = 0.0, or Off)
106
Download from Www.Somanuals.com. All Manuals Search And Download.
Speed Calibration
(Advanced, with Speed paddlewheel only)
Daylight Saving Time
(Advanced)
Speed Calibration will adjust the speed readout by the percentage entered,
and will appear in the menu if a Speed accessory is connected and the
paddlewheel has moved at least once, when the unit is in Advanced User
Mode (see Setup Menu Tab: User Mode.)
Daylight Saving Time adjusts the time display to account for local Daylight
Saving Time. Selecting On adds one hour to the time display adjusted for
your local time zone. Selecting Off leaves the time display as adjusted for
your local time zone. This menu choice is available only when in Advanced
User Mode (see Setup Menu Tab: User Mode.)
To change the Speed Calibration setting:
To change the Daylight Saving Time setting:
1. Make sure you are in Advanced User Mode, then highlight Speed
Calibration on the Setup menu.
1. Make sure you are in Advanced User Mode, then highlight Daylight
Saving Time on the Setup menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
Speed Calibration setting. (-20% to +20%, Default = 0%)
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to turn Daylight
Saving Time On or Off. (Off, On, Default = Off)
Local Time Zone
(Advanced)
Position Format
(Advanced)
Local Time Zone selects your time zone in reference to the time reported by
the GPS receiver when Time+Date is selected as a Digital Readout on the
Sonar View (see Select Readouts). This menu choice is available only when
in Advanced User Mode (see Setup Menu Tab: User Mode.)
Position Format selects the format of the latitude and longitude position
display. This menu choice is available only when in Advanced User Mode
(see Setup Menu Tab: User Mode.)
To change the Local Time Zone:
To change the Position Format setting:
1. Make sure you are in Advanced User Mode, then highlight Position
Format on the Setup menu.
1. Make sure you are in Advanced User Mode, then highlight Local
Time Zone on the Setup menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Position
Format. (dd.ddddd°, dd°mm.mmm', or dd°mm'ss", Default = dd°mm.mmm')
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
Local Time Zone (Default = EST [UTC-5] - Eastern Standard Time).
107
Download from Www.Somanuals.com. All Manuals Search And Download.
Time Format
(Advanced, International only)
Date Format
(Advanced, International only)
Time Format changes the time format used by the unit This menu choice is
available only when in Advanced User Mode (see Setup Menu Tab: User
Mode.) International models only. Time Format selects a 12 hour or 24 hour
format for the time of day displayed when Time + Date is selected as a
Digital Readout on the Sonar View (see Select Readouts).
Date Format changes the date format used by the unit This menu choice is
available only when in Advanced User Mode (see Setup Menu Tab: User
Mode.) International models only. Date Format selects the format for the date
display when Time + Date is selected as a Digital Readout on the Sonar View.
(see Select Readouts).
To change the Time Format:
To change the Date Format:
1. Make sure you are in Advanced User Mode, then highlight Time
Format on the Setup menu.
1. Make sure you are in Advanced User Mode, then highlight Date
Format on the Setup menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
Time Format. (12 hour, 24 hour, Default = 12 hour)
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
Date Format. (mm/dd/yy, dd.mm.yy or yy.mm.dd, Default =
mm/dd/yy)
108
Download from Www.Somanuals.com. All Manuals Search And Download.
Digits Format
(Advanced)
NMEA Output
(Advanced)
Digits Format allows you to add a tenth decimal place to readouts such as
Temperature and Depth. The format can be changed to small format, large
format or no format. This menu choice is available only when in Advanced
User Mode (see Setup Menu Tab: User Mode.)
NMEA Output turns the NMEA output on or off. This menu choice is available
only when in Advanced User Mode (see Setup Menu Tab: User Mode.)
The following NMEA sentences are output:
DPT - Depth
To change the Digits Format setting:
MTW - Water Temperature
GLL - Lat/Lon Position
1. Make sure you are in Advanced User Mode, then highlight Digits
Format on the Setup menu.
GGA - GPS Fix Data
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
Digits Format setting. (Small tenths, Large tenths, No tenths,
Default = Small tenths)
RMC - Recommended Minimum Specific GNSS Data
VTG - Course Over Ground and Ground Speed
ZDA - Time and Date
When navigating, the following NMEA sentences are also output:
APB - Autopilot Sentence B
BWR - Bearing and Distance to Waypoint
RMB - Recommended Minimum Navigation Info
To turn NMEA Output on or off:
1. Make sure you are in Advanced User Mode, then highlight NMEA
Output on the Setup menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
NMEA Output to On or Off (Off, On, Default = Off).
109
Download from Www.Somanuals.com. All Manuals Search And Download.
Sonar
Views Menu Tab
Sonar deactivates Sonar and removes the
Sonar Views from the view rotation.
From any view, press the MENU key twice to
access the tabbed Main Menu System, then
press the RIGHT 4-WAY Cursor Control key until
the Views tab is selected. This menu tab allows
you to set the available views to either hidden
or visible in the view rotation. The view will be
removed from the view rotation if it is set to
Hidden and will be displayed in the view
rotation if it is set to Visible.
To turn Sonar on or off:
1. Highlight Sonar on the Setup menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
Sonar to On or Off (Off, On, Default = On).
Views Menu
110
Download from Www.Somanuals.com. All Manuals Search And Download.
The following views are available:
To Change the View Status of Any View:
1. Highlight the View main menu tab.
• Bird’s Eye View
2. Use the UP or DOWN 4-WAY Cursor Control keys to select a View.
• Chart/Bird’s Eye Combo View
• Chart/Chart Combo View
• Chart View
3. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the
status of the view from Hidden to Visible or vice versa.
• Chart/Sonar Combo View
• Side Beam View
(only with QuadraBeam PLUS™ transducer,
optional-purchase on the 917c Combo and included
with the 957c Combo)
• Sonar View
• Sonar Zoom View
• Split Sonar View
• Snapshot and Recording View
• Self Test
• Accessory Test
• GPS Diagnostic View.
111
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories Menu Tab
Using Screen Snapshot
From any view, press the MENU key twice to access the tabbed Main Menu
System, then press the RIGHT cursor key until the Accessories tab is selected.
Screen Snapshot activates the screen
snapshot function. When Screen Snapshot is enabled, pressing the MARK
key creates a saved screen capture on the optional-purchase MMC/SD card
installed in your unit’s card slot. All menus, dialog boxes, warnings and
messages are captured and saved automatically.
If no accessories are attached to the Accessory Bus, no accessory menu
choices will appear under the Accessories tab, only the Screen Snapshot
menu choice. If an accessory is attached, however, additional menu choices
that support the accessory will be added automatically. See the Operations
Manual that comes with your accessory for detailed information.
Once you have created a screen capture, a screen capture thumbnail is
added to the Snapshot and Recording View, and is available to view at a
later date. See the full-sized image by highlighting a thumbnail (using the Up
or Down 4-Way Cursor keys), then using the Right 4-Way Cursor key to view
the full image. A border around the full-size screen snapshot indicates that
it is just a screen snapshot, not a “live” view. You can delete the highlighted
image, or all images, by selecting a thumbnail and using Delete Image, or
using Delete All Images from the Snapshot and Recording X-Press™ menu.
You can view these captures on the Snapshot and Recording View, which
shows any existing thumbnails of the screen captures, along with any icons
representing sonar recordings.
Accessories Menu
(no accessories attached)
Accessories Menu
(with accessories attached)
NOTE: Accessories to enable WeatherSense® and the SmartCast® Wireless Sonar Link
(WSL) require separate purchases. You can visit our website at www.humminbird.com
or contact our Customer Resource Center at 1-800-633-1468 for additional details.
NOTE: You must have an optional-purchase MMC/SD card installed for the
Screen Snapshot feature to work.
NOTE: If you use your MMC/SD card in two different Fishfinder units that have
different screen sizes, the recordings made on one unit will still be present on the
card, but will be represented by the Unavailable icon (circle with a slanted line
through it) on the Snapshot and Recording View on the other unit.
112
Download from Www.Somanuals.com. All Manuals Search And Download.
To turn Screen Snapshot on or off:
To view screen snapshots:
1. Highlight Screen Snapshot on the Accessories main menu.
1. Make sure that the optional-purchase MMC/SD card used to
capture the screen is installed in your card slot.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to turn Screen
Snapshot On or Off (Off, On, Default = Off).
2. Press the VIEW key until you see the Snapshot and Recording View.
To make a screen snapshot (Screen Snapshot must be enabled):
3. You can scroll through the whole list of captures in this view using
the 4-WAY Cursor keys. Highlight a thumbnail (using the Up or
Down 4-Way Cursor keys), then use the Right 4-Way Cursor key to
view the full image. A border around the full-size screen capture
indicates that it is just a screen capture, not a “live” view. You can
delete the highlighted image, or all captured images, using the
Snapshot and Recording X-Press™ menu. (See Snapshot and
Recording X-Press™ menu: Delete Image and Delete All Images
for more information).
1. Make sure you have installed an optional-purchase MMC/SD card
into your card slot.
2. From any view you want to capture, press the MARK key. When you
start a screen capture, you will see a message that a waypoint has
been created at the point where your cursor is on the screen, and
the screen will freeze while the snapshot is being saved to the
MMC/SD card. A status dialog box will appear that shows the
progress of the save as a percentage, and that displays the
numbered file name assigned to the .BMP file that is being created.
NOTE: When you highlight a snapshot thumbnail, the amount of room remaining
on the SD card will be displayed.
NOTE: For more information, see Snapshot and Recording View and Snapshot
and Recording X-Press™ Menu.
NOTE: The waypoints that are created by a snapshot have the same name as the
file and use a custom waypoint icon. Snapshot filenames begin with the letter "S".
NOTE: Navigation is not affected by the Screen Snapshot feature. Also, if Screen
Snapshot is enabled but there is no GPS receiver connected, pressing the MARK
key will capture the screen image and display an error saying that a GPS position
fix is required to create a waypoint.
NOTE: You may view data files associated with each screen snapshot by
removing the MMC/SD card from your unit and installing it in your optional-
purchase MMC/SD card reader connected to a PC. Use Windows Explorer to see
the contents of your MMC/SD card; you will notice that a .DAT (may show up as
.TXT) file is created for every .BMP screen capture; this data file includes the
thumbnail view, and is required in order to be able to view the screen snapshot
from your unit, so don’t delete these files.
NOTE: The speed of the capture depends on the type of card you use; in general,
SD cards capture the screen faster than MMC cards do.
113
Download from Www.Somanuals.com. All Manuals Search And Download.
900 Series™ Defaults to Simulator
with a Transducer Attached
Troubleshooting
Before contacting the Humminbird® Customer Resource Center, please read
the following section. Taking the time to review these troubleshooting
guidelines may allow you to solve a performance problem yourself, and
therefore avoid sending your unit back for repair.
A connected and functioning transducer will cause the newly-started 900
Series™ to go into Normal operating mode automatically. If, when you
power up the 900 Series™, it goes into Simulator mode automatically, even
though a transducer is already connected, this means that the control head
is not detecting the transducer. Perform the following troubleshooting tasks:
900 Series™ Doesn’t Power Up
• Using the Installation Guide that also comes with your 900 Series™,
check to make sure that the transducer cable is securely connected
to the 900 Series. Reconnect if necessary, and power up the 900
Series™ again to see if this fixes the problem.
If your 900 Series™ doesn’t power up, use the Installation Guide that also
comes with it for specific confirmation details, making sure that:
• the power cable is properly connected to the 900 Series™ control
head,
• Replace the non-functioning transducer with a known good
transducer if available and power up the control head again.
• the power cable is wired correctly, with red to positive battery
terminal and black to negative terminal or ground
• Check the transducer cable. Replace the transducer if the cable is
damaged or corroded.
• the fuse is operational
• the battery voltage of the power connector is at least 10 Volts.
Correct any known problems, including removing corrosion from the battery
terminals or wiring, or actually replacing the battery if necessary.
114
Download from Www.Somanuals.com. All Manuals Search And Download.
Display Problems
There are several main conditions or sources of possible interference that may cause problems with the quality of the information displayed on the control head.
Look in the following table for some symptoms of display problems and possible solutions:
Problem
Possible Cause
The control head loses power at high
speeds.
If the power output of your boat’s engine is unregulated, the control head may be protecting itself using
its over-voltage protection feature. Make sure the input voltage does not exceed 20 Volts.
When the boat moves at higher speeds,
the bottom disappears or suddenly
weakens, or the display contains gaps.
The transducer position may need to be adjusted. A mix of air and water flowing around the transducer
(cavitation) may be interfering with the interpretation of sonar data. See your Installation Guide for
suggestions on adjusting the transducer position.
Electrical noise from the boat’s engine may be interfering with sonar reception. See Finding the Cause
of Noise for more information.
There are no fish detected, even when you Sonar readings may be affected if the transducer is not positioned correctly (i.e. mounted at an angle,
know they are in the water under the
boat, or sonar readings seem weak or
faulty.
not straight down), or there is some kind of mechanical interference, either because it is mounted inside
a hull that is too thick for proper sonar transmission, the bond between the transducer and the hull is
not airtight, or because the transducer is dirty. Check with your Installation Guide for guidance on re-
positioning the transducer, and make sure the transducer is clean.
Low battery voltage may be affecting the power of signal transmission.
Electrical noise from the boats engine may be interfering with sonar reception. See Finding the Cause
of Noise for more information.
115
Download from Www.Somanuals.com. All Manuals Search And Download.
Finding the Cause of Noise
Electrical noise usually affects the display with many black dots at high speeds, and high sensitivity readings. One or more of the following sources can cause
noise or interference:
Possible Source of Noise
Other electronic devices
Isolation
Turn off any nearby electronic devices to see if the problem goes away, then turn them on one at a time
to see if the noise re-appears.
The boat’s engine
To determine whether the boat’s engine is the source of the noise, increase the RPMs while the boat
is in neutral and stationary to see if the noise increases proportionately; if noise appears when you rev
the engine, the problem could be the spark plugs, alternator, or tachometer wiring. Replace the spark
plugs with resistor plugs, install an alternator filter, or route the control head power and transducer
cables away from the engine wiring.
Cavitation from the boat’s propeller
Turbulence created by the propeller can cause noise; make sure the transducer is mounted at least 15”
(38 cm) from the propeller, and that the water flows smoothly over the face of the transducer at all times.
116
Download from Www.Somanuals.com. All Manuals Search And Download.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER WARRANTIES,
OBLIGATIONS OR LIABILITIES ON THE PART OF HUMMINBIRD® AND WILL
BE THE CUSTOMER'S EXCLUSIVE REMEDY, EXCEPT FOR ANY APPLICABLE
IMPLIED WARRANTIES UNDER STATE LAW WHICH ARE HEREBY LIMITED
IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE. IN
NO EVENT WILL HUMMINBIRD® BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED
WARRANTY RELATING TO THE PRODUCTS.
1-Year Limited Warranty
We warrant the original retail purchaser that products made by
Humminbird® have been manufactured free from defects in materials and
workmanship. This warranty is effective for one year from the date of original
retail purchase. Humminbird® products found to be defective and covered by
this warranty will be replaced or repaired free of charge at Humminbird’s
option and returned to the customer freight prepaid. Humminbird’s sole
responsibility under this warranty is limited to the repair or replacement of a
product that has been deemed defective by Humminbird®. Humminbird® is
not responsible for charges connected with the removal of such product or
reinstallation of replaced or repaired parts.
Some states do not allow limitations on an implied warranty, or the exclusion
of incidental or consequential damages, so the above exclusions may not
apply to you. You may also have other rights, which vary from state to state.
This warranty does not apply to a product that has been:
• Improperly installed;
Humminbird® Service Policy
Even though you'll probably never need to take advantage of our incredible
service policy, it's good to know that we back our products this confidently.
We do it because you deserve the best. We will make every effort to repair
your unit within three business days from the receipt of your unit at our
factory. This does not include shipping time to and from our factory. Units
received on Friday are typically shipped by the following Wednesday, units
received Monday are typically shipped by Thursday, etc.
• Used in an installation other than that recommended in the product
installation and operation instructions;
• Damaged or has failed because of an accident or abnormal
operation;
• Repaired or modified by entities other than Humminbird®.
Please retain your original receipt as a proof of the purchase date. This will
be required for in-warranty service.
All repair work is performed by factory-trained technicians to meet exacting
factory specifications. Factory-serviced units go through the same rigorous
testing and quality control inspections as new production units.
After the original warranty period, a standard flat rate service charge will be
assessed for each repair (physical damage and missing parts are not included).
Any repairs made after the original warranty will be warranted for an additional
117
Download from Www.Somanuals.com. All Manuals Search And Download.
90 days after service has been performed by our factory technicians. You can
contact our Customer Resource Center or visit our website to verify the flat rate
repair fee for your product (visit the Product Support section):
For IN-WARRANTY service, complete the following steps:
•
Obtain a Repair Authorization Number from the Humminbird®
Customer Resource Center.
http://www.humminbird.com
•
Tag product with your name, street address, phone number and your
assigned Repair Authorization Number.
We reserve the right to deem any product unserviceable when replacement
parts are no longer available or impossible to obtain. This Service Policy is
valid in the United States only. This applies only to Humminbird® products
returned to our factory in Eufaula, Alabama. This Service Policy is subject to
change without notice.
•
•
•
Include a brief written description of the problem.
Include a copy of your receipt (to show proof and date of purchase).
Return product freight prepaid to Humminbird®, using an insured
carrier with delivery confirmation.
Returning Your Unit for Service
For OUT-OF-WARRANTY service, complete the following steps:
Before sending your unit in for repair, please contact the factory, either by
phone or by email, to obtain a Repair Authorization Number for your unit.
Please have your product model name and serial number available before
calling the factory. If you contact the factory by e-mail, please include your
product model name and serial number in the e-mail, and use Request for
Repair Authorization Number for your e-mail subject header. You should
include your Repair Authorization Number in all subsequent
communications about your unit.
•
•
•
Obtain a Repair Authorization Number from the Humminbird®
Customer Resource Center.
Include payment in the form of credit card number and expiration
date, money order or personal check. Please do not send cash.
Tag product with your name, street address, phone number and your
assigned Repair Authorization Number.
•
•
Include a brief written description of the problem.
Return product freight prepaid to Humminbird®, using an insured
carrier with delivery confirmation.
118
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Sonar Link (WSL): purchase the Wireless Sonar Link (WSL)
accessory to receive remote sonar signals from a SmartCast® Remote Sonar
Sensor (RSS). Radio signals from the RSS are received by the WSL and are
transmitted over the Accessory Bus to the 900 Series™.
900 Series™ Accessories
Accessories customize the 900 Series™ to your needs and enable you to stay
on the edge of new technology. When an accessory is connected to the 900
Series™, additional menus and readouts are added automatically to the
Main Menu System. Accessories available today that are supported by your
900 Series™ include:
PC Connect Cable: Purchase the PC Connect Cable to connect the 900
Series™ Fishing System to a PC in order to upload product software updates
and new features obtained from www.humminbird.com. This accessory
requires the MSWindows-compatible HumminbirdPC™ software
downloaded from our website to your PC in order to communicate with the
900 Series™ Fishing System.
QuadraBeam PLUS™ transducer: purchase and connect the QuadraBeam
PLUS™ transducer to your 900 Series™ Fishing System to access specialized
QuadraBeam PLUS™ functions such as two 45° fan-shaped 35° 455 kHz
Side Structure locating sonar beams to spot fish, bait and structure to the
left and right of the boat over an area of the bottom that’s always equal to
twice your depth, for a continuous 90° of uninterrupted side to side
coverage to 160 feet.
Universal Sonar 2: Your 900 Series™ Fishing System supports Universal
Sonar 2, a state-of-the-art, integrated and protected transducer that is built
into the lower unit of Minnkota trolling motors. With Universal Sonar 2, all
wiring is concealed inside the indestructible composite shaft—out of sight
and out of harm’s way, with no clamps, ties, or exposed wires. Universal
Sonar 2 features new temperature sensing and the performance of
DualBeam PLUS™ technology (available with all Humminbird® DualBeam
PLUS™ models). An expanded view and greater bottom detail gives you a
totally new perspective of the water below, along with optimal sonar
performance to help you find fish.
WeatherSense® Fishing Condition Monitor: purchase and plug in the
WeatherSense® accessory to your 900 Series™ to obtain barometric
pressure readouts and trend data in real time.
GPS Connection Cable: purchase the GPS Connection Cable in order to
connect a handheld or other NMEA* GPS-compatible device that you may
already own to your 900 Series™.
*NMEA 0183 is a National Marine Electronics Association standard for data
communication.
119
Download from Www.Somanuals.com. All Manuals Search And Download.
Downriggers are the key to catching fish you otherwise couldn’t even touch.
And now Humminbird’s CannonLink™ Downrigger Controller makes
operation of up to six Cannon™ Mag 20 DT or Mag 20 DT/HS downriggers
incredibly easy. Using the controls on your Fishing System, deploy or retrieve
downriggers, hold a specific distance off the bottom, cycle downriggers
between two depths, and adjust the Positive Ion Control. Even see
temperature and water clarity at depth and speed at the ball right on-screen
when using the Cannon™ Speed-n-Temp. You’ll never be shorthanded again,
just make adjustments from the helm, while your mate rigs the lines and
brings in the fish!
Be sure to check out our website www.humminbird.com for additional new
and exciting accessories to grow your 900 Series™.
NOTE: Each accessory requires a separate purchase. You can visit our
website at www.humminbird.com or contact our Customer Resource Center at
1-800-633-1468 for additional details.
With the new InterLink™ Network Connection, you can now share GPS
position, waypoints, routes and your current track between two
Humminbird® Fishing Systems in real time. Mark a waypoint at the console,
and it’s instantly available on the second unit. No matter where you’re at on
the boat, you’ll have access to your critical fishing and navigation
information. Plus, daisy chain InterLink™ with other System Modules and
you’ll have a network that lets you share digital data around the boat. It’s a
simply, clearly, better networking solution!
120
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
NOTE: Product specifications and features are subject to change without notice.
Depth Capability
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1500 ft (500 m)
NOTE: Humminbird® verifies maximum stated depth in saltwater conditions,
however actual depth performance may vary due to transducer installation,
water type, thermal layers, bottom composition and slope.
Power Output
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500 Watts (RMS); 4000 Watts (Peak-To-Peak)
Operating Frequency
POLICY ON ENVIRONMENTAL COMPLIANCE: It is the intention of
Humminbird® to be a good corporate citizen and comply and meet all known and
applicable environmental regulations in the areas and countries where our
products are sold. We will promote and implement environmentally sound
processes in support of national and international regulations.
917c Combo: . . . . . . . . . . . . . . . . 200 kHz and 83 kHz DualBeam PLUS™
957c Combo: . . . . . . 200 kHz, 83 kHz and 455 kHz QuadraBeam PLUS™
Area of Coverage
917c Combo: . . . . 60° @ -10 dB in 83 kHz and 20° @ -10 dB in 200 kHz
957c Combo: . . . . . . . 60° @ -10 dB in 83 kHz; 20° @ -10 dB in 200 kHz
and 35° (2) @ -10 dB in 455 kHz (90° Total Coverage)
ROHS STATEMENT: Product designed and intended as a fixed installation or
part of a system in a vessel may be considered beyond the scope of Directive
2002/95/EC of the European Parliament and of the Council of 27 January 2003
on the restriction of the use of certain hazardous substances in electrical and
electronic equipment.
Target Separation . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1/2 Inches (63.5 mm)
Power Requirement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-20 VDC
LCD
917c Combo: . . . . . . . . . . . . . . . . . 480 V x 800 H; 7" Diagonal Color TFT
957c Combo: . . . . . . . . . . . . . . . . . 480 V x 800 H; 8" Diagonal Color TFT
WEEE STATEMENT: Product designed and intended as a fixed installation or
part of a system in a vessel may be considered beyond the scope of Directive
2002/96/EC of the European Parliament and of the Council of 27 January 2003
on waste electrical and electronic equipment (WEEE).
Transducer
917c Combo: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . XNT 9 20 T
957c Combo: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . XNT 9 QB 90 T
CALIFORNIA PROPOSITION 65 STATEMENT: Lead in cable jackets and boots
is restricted to 300 parts per million or less as determined by ICP-AES test
methods.
Transducer Cable Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 ft (6 m)
121
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
Sonar Terms
Alarm, Depth: Depth Alarm is a user-controllable, audible alert that sounds
Cavitation: Cavitation is the effect of air bubbles created as the propeller rotates
when depth is less than or equal to the setting.
and the boat moves through the water.
Alarm, Temperature: Temperature Alarm is a user-controllable, audible alert that
sounds when the water surface temperature equals the setting.
Chart Speed: Chart Speed is a user-controllable feature that sets the speed at
which sonar information moves across the display. A faster setting displays
sonar information from more pings and shows more detail, but the information
moves quickly across the display: a slower setting permits viewing of more sonar
history, but does not display as much detail. The best setting is often the user's
personal choice.
Backlight: Backlight is a user-controllable illumination for the LCD for night and
low light use.
Beam (Sonar Beam): A sonar beam is the wide, cone-shaped projection of
sound waves formed as sound travels underwater. See Cone Angle.
Cone Angle: The cone angle is the angular measurement of the sonar beam at
a specific dB down point (i.e. -10 dB). See dB Down Point.
Big Digits View: Big Digits View is a Humminbird® feature that displays the sonar
graph and enlarged digital readouts for easy reading from a distance. This is a great
tool when monitoring the digital depth is important - such as with higher boat
speeds, or when viewing the unit from a distance. When speed input is available,
the Big Digits View also shows the TripLog. See TripLog.
Customizable Digital Readouts: Customizable Digital Readouts is a
Humminbird® feature that permits the user to select the specific digital
information that appears in the main Sonar view (i.e. Speed, Temperature,
Barometric Pressure, TripLog, etc.)
Bottom Black: Bottom Black is a Humminbird® feature that "fills in" the area of
the display below the bottom contour. Bottom Black is preferred by some anglers
because of its high contrast and easy readability, even though it can obscure
bottom hardness information.
Dead Zone: The dead zone is the area of the sonar beam that receives the sonar
signal after the main bottom return. Fish and other objects close to the bottom
that fall within the dead zone will probably not be visible in the sonar beam.
Precision sonar beams, such as the Humminbird® 20° beam, have a smaller dead
zone than wider sonar beams.
Bottom Contour: Bottom Contour is the profile of the bottom graphed to the
display as the depth changes.
Decibel: A Decibel is the measurement for sound pressure level, or "intensity" of the
sonar return. See dB Down Point.
Bottom Hardness: Bottom Hardness is the density (or composition) of the
bottom, which can often be determined by interpreting the main sonar return.
Varying levels of hardness can be determined by interpreting the "thickness" of
the sonar return. Hard returns appear thin and black, softer returns appear
thicker and less black. It is important to note that a sonar return from a sloping
bottom can have the appearance of a softer bottom.
dB Down Point: The dB Down Point is the standard decibel level at which the sonar
cone angle is measured, and is written as "@ -10 dB" or "@ -3 dB". Measurements
at smaller down points (bigger negative numbers) indicate that the less intensive
sonar signals are being used for the measurement.
122
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
Sonar Terms
Display, FSTN: FSTN is an acronym for Film Super-Twist Nematic. FSTN is a
monochrome display technology characterized by black, high-contrast pixels. All
monochrome fixed mount Humminbird® products use FSTN technology.
Freeze Frame: Freeze Frame is a Humminbird® feature that pauses the sonar
scrolling so that the image on screen can be studied with greater detail. See
Instant Image Update.
Frequency: Frequency is a measure of the number of sound wave cycles per second
of a sound impulse transmitted underwater. A typical frequency for fishfinders is
200 kHz, which offers a good balance of performance under many conditions.
Lower frequencies, such as 50 kHz, are capable of penetrating to greater depths,
but with less resolution. Higher frequencies, such as 455 kHz, offer greater
resolution, but are limited in depth performance. Humminbird® uses a variety of
frequencies that are optimized for specific applications.
DualBeam PLUS™: DualBeam PLUS™ is a Humminbird® sonar configuration that
uses two sonar beams simultaneously, and combines the information from both
beams into one view by overlapping the data on-screen, or shows each beam
individually side by side, or permits each beam to be viewed individually full screen.
Feature Memory: Feature Memory is a Humminbird® feature that retains the user's
menu settings in permanent memory. Settings are retained even when the unit is
powered off indefinitely.
Grayscale: Grayscale is the use of varying shades of gray to represent the strength
of the sonar signal on the display , and is a very intuitive method of presenting
information. Traditionally, the strongest sonar signals are represented in black, and
progressively weaker signals are represented in progressively lighter shades of gray.
Fish Arch: A Fish Arch is the apparent "arch" that appears on the display when any
object moves through the sonar cone. The arch results from a gradual decrease in
distance to an object as it moves into the sonar cone. The distance to an object
changes due to the conical shape of the sonar beam, which causes the distance to
be greater at the edges of the beam than at the center of the beam. When this
distance change is graphed on the display, an arch appears.
Grayscale, Inverse: Inverse Grayscale is a Humminbird® feature that reverses the
correlation of sonar signal strength and the shade of gray typically used to
represent it. The strongest sonar signals are represented by "white", and
progressively weaker signals are represented in progressively darker shades of gray.
While somewhat counter-intuitive, this method makes the sonar images crisper,
and has the benefit of enhancing the apparent sensitivity because the weaker
signals appear bolder. Inverse grayscale works well in very clear water. Debris-laden
water often appears as a lot of clutter on the screen.
Fish ID+™: Fish ID+™ is a Humminbird® feature that uses advanced sonar
processing algorithms to determine if a detected object is likely to be a fish. When
the sonar signal from an object meets strict parameters, the unit draws a Fish
Symbol (or icon) and the digital depth of the target. On DualBeam and DualBeam
PLUS™ units, fish detected in the narrow center beam are shown as shaded
symbols, and fish detected in the wider beam are shown as hollow symbols.
Instant Image Update: Instant Image Update is a Humminbird® feature that
updates all the sonar information on the display when Sensitivity and a variety of
sonar settings (Bottom View, Range, etc.) are modified. This differs from the
traditional functionality that only updates the new sonar information collected after
the setting change. Instant Image Update permits more accurate fine-tuning of the
Fish Symbol: A Fish Symbol is the graphic that is displayed on the screen when Fish
ID+™ determines that a sonar return is likely to be a fish. See Fish ID+™.
123
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
Sonar Terms
display because the user can see the results on the complete sonar graph. When
combined with the Freeze Frame feature, the user can adjust and understand the
effects of many different sonar settings quickly and easily.
In fishfinders, the total resolution (vertical multiplied by horizontal) is often less
important than the "Vertical Pixel" resolution. See Pixels, Vertical.
Pixels, Vertical: Vertical Pixels are a number of vertical picture elements in a single
column on an LCD display. A greater number of vertical pixels provide finer
resolution of targets detected by sonar. Essentially, a vertical distance (the depth),
when divided by a larger number, breaks that distance into smaller samples, each
representing a smaller area and thus providing more detail. In fishfinders, vertical
pixels are more critical than horizontal pixels because the horizontal axis of the
display represents time, or history. Sonar information on the horizontal axis can vary
greatly, depending on boat speed and the Chart Speed setting. A greater number
of horizontal pixels show more sonar history that the boat has passed through. On
many models, Humminbird® provides the most vertical pixels to provide a better
display resolution. See Chart Speed and Pixels.
Maximum Depth Menu: The Maximum Depth Menu is a Humminbird® feature that
optimizes performance based on the maximum operational depth set by the user.
Many Humminbird® units can operate across a very broad depth range (up to 2500
feet) which causes the unit to "look" up to that full depth under some
circumstances. Due to the speed of sound in water, this can result in less
responsiveness because the unit has to wait for a longer period of time to receive
the sonar signal. When the Maximum Depth menu is set to a lower value, the unit
only looks up to the setting, which increases the responsiveness of the unit. This is
an important feature for anyone operating in shallower depths!
Noise: Noise is unintentional, external sound waves that interfere with the optimal
operation of sonar. Noise appears as random "dots" on the display, and is caused
by a variety of sources. Electrical noise (from trolling motors, bilge pumps, VHF
radios) typically manifests as a consistent dot pattern. Electrical noise can be
isolated by selectively turning on and off other electrical devices to determine the
source. Often re-routing the power cable, or connecting to an alternative power
supply (second battery) can help overcome electrical noise. Hydrodynamic noise
(from propeller and/or hull cavitation) has a more random appearance and is
generally related to boat speed, so that faster operation results in more noise.
Hydrodynamic noise can be overcome by proper transducer installation. Many
Humminbird® products have a Noise Filter menu setting that allows the user to
clear the screen of noise that is difficult to eliminate.
Power Output: Power output is the amount of sound energy emitted into the water
by the sonar transmitter. Power output is measured using either RMS (Root Mean
Square) or P-T-P (Peak-to-Peak) measurement systems. Either method is acceptable,
but it is important, when comparing power outputs, to make sure that the same
measurement system is being used for both outputs, because P-T-P numbers are 8
times higher than RMS numbers. Greater power output allows the sonar signal to
penetrate through weeds and thermoclines, reach deeper depths and operate more
effectively in noisy environments, such as when the boat is running at high speed.
Pulse Width (Pulse Length): Pulse Width is the length of time that a sonar sound
burst is transmitted into the water. Shorter pulse widths provide better target
separation, but cannot travel to great depths. Longer pulse widths provide better
depth penetration, but result in poorer target separation. Humminbird® varies pulse
width based on depth to optimize both target separation and depth performance.
See Target Separation.
Pixels: Pixels are the "picture elements", or small square blocks, that make
up the image on the LCD. Measured as a vertical by horizontal number
(i.e. 640 V x 320 H), this key specification typically indicates the quality of resolution.
124
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
Sonar Terms
QuadraBeam PLUS™: QuadraBeam PLUS™ is a Humminbird® sonar configuration
that uses four sonar beams for a more detailed bottom image. QuadraBeam PLUS™
uses the DualBeam PLUS™ configuration for downlooking, and also adds two
additional beams to look to the left and right. The sonar beams pointing to the left
and right provide the ability to spot fish and structure over a wide 90° area, and to
identify on which side of the boat they are located. See DualBeam PLUS™.
in shallow water and over hard bottoms; it is actually possible to see a third sonar
return under some circumstances. The second return provides useful information to
help determine bottom hardness, as areas with harder bottoms will generally create
a second return. The second return can be used as a guide to set Sensitivity when
in shallower water.
Sensitivity: Sensitivity is a user feature that adjusts the sensitivity of the sonar
system to show more or less detail in the water. Higher sensitivities are often
preferred, however, when the water contains debris (silt, storm debris, etc.) and it
can be difficult to pick out targets. Conversely, if sensitivity is set too low, relevant
targets may be missed.
Quick Disconnect Mount: The Quick Disconnect Mounting system is an exclusive
Humminbird® feature that permits the unit to be easily removed from the mounting
base by pressing a release button, and re-installed by simply snapping it back into
place. All cable connections are made when installing, so that no separate wiring
connections are required. Additionally, the mount offers 90° tilt and 360° swivel
capability to adjust the viewing angle of the unit as you move about the boat.
SONAR: SONAR is the acronym for SOund and NAvigation Ranging. Sonar
technology uses precision sound bursts transmitted underwater to determine the
distance and other attributes of objects in the water. Distance can be determined
because the speed of sound in water is constant, and the time for the signal to
return is measured. Sound also travels very quickly underwater, making sonar a
responsive, cost-effective tool. Sonar is the basic technology behind all recreational
and commercial fishfinding and depthfinding devices.
Real Time Sonar: Real Time Sonar is a Humminbird® technology that delivers ultra-
fast sonar transmitter/receiver operation and results in a more detailed
instantaneous view of what is under the boat. The Real Time Sonar window is a
vertical band at the right side of the display that shows the instantaneous sonar
return from the transducer at a particular instant. The RTS® Window menu option
permits the user to adjust the window to show the full sonar signal return, or just
a narrower band that indicates intensity using grayscale. Real Time Sonar relies on
very fast Sonar Update Rate (Ping Speed). See Sonar Update Rate.
Sonar Echo Enhancement: Sonar Echo Enhancement is a Humminbird® feature
that describes the high degree of sonar sensitivity achieved through a combination
of transmitter/receiver and software algorithms. The result of Sonar Echo
Enhancement is to display virtually everything in the water that is of interest to the
angler, including bait fish, game fish, thermoclines, weed beds, subtle structure,
and more.
Receiver: See Transmitter.
Second Return: The Second Return is a term that describes the appearance of a
second sonar return below the primary sonar return (bottom contour) at exactly
twice the true depth. The second return is caused by the same sonar energy
bouncing off the bottom once, rebounding to the water surface and then traveling
back down to the bottom to be reflected again. Second returns are more common
Sonar Update Rate: Sonar Update Rate is the number of times per second that the
transmitter/receiver sends and receives sonar signals. A very fast sonar update rate
collects more information and provides a more detailed image of the bottom, fish
125
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
Sonar Terms
and structure. Many Humminbird® units operate at up to 40 times per second when
in single frequency operation. Due to the limitation of the speed of sound in water,
the update rate begins to slow as depth increases to deeper than 50 feet. In very
shallow water (less than 10 feet), however, update rates as much as 60 times per
second can be achieved.
air bubbles. Typically, saltwater environments have significantly greater surface
clutter than freshwater due to continuous wind and wave action that causes
aeration at the surface. The Surface Clutter menu provides manual control to bias
the default settings under extreme conditions.
Target Separation: Target Separation is the measurement of minimum distance
that a fishfinder needs to be able to recognize two very close objects as two distinct
targets (i.e. two fish hanging very close, or a fish hanging very close to structure).
Humminbird® fishfinders provide a very good 2 1/2 inches of target separation in
shallower than 100 feet of depth. Target separation decreases as depth increases
due to the need for longer Pulse Width to achieve greater depth. See Pulse Width.
Speed: Speed is the rate at which the boat moves through the water. Boat speed
can be measured as Speed Over Ground or Speed Through Water. Speed Over
Ground is provided by GPS, and is the measurement of the boats progress across
a given distance. Speed Through Water is provided by a speed paddlewheel, and
is the measurement of the flow past the boat, which may vary depending on
current speed and direction. Speed Through Water is most critical for anglers
using downriggers, as it impacts the running depth of the down riggers. Speed
Over Ground is optimal for navigation, as accurate destination times can be
derived from this measurement. Humminbird® products allow for input and
display of both sources.
Thermoclines: Thermoclines are water layer(s) of distinctly different temperatures
that create a sonar reflection due to the density of the differing water temperatures.
Typically a thermocline will appear as a continuous band across the display at some
distance above the bottom contour. Thermoclines are of interest to anglers because
fish will suspend above or below the thermocline as they seek the optimum
temperature and oxygen levels.
Structure: Structure is a general term for objects on the bottom that present a
discontinuity and are a likely attractor for fish. This includes bottom contour features
(drop-offs, humps, and holes), standing structure (stumps, timbers, brush piles) and
a wide range of other potential objects (sunken boats, reefs). Humminbird® units
excel at showing structure with great detail over a wider area due to unique sonar
configurations developed for the angler.
Time Variable Gain: Time Variable Gain is a processing step applied to the sonar
return to "normalize" the data so that objects of equal size (i.e. fish) appear to be
the same size, even if they are separated by a good distance. Time Variable Gain is
a fundamental attribute of good sonar, but is often promoted as a feature.
Total Screen Update®: A Humminbird® feature that refreshes and updates all
the sonar information on the display when a range change occurs. Without Total
Screen Update®, only the most recent sonar information would be drawn to the
new range, and the old sonar information would continue to scroll off the screen
at the old range.
Structure ID®: Structure ID® is a Humminbird® feature that describes the traditional
grayscale method of presenting sonar information. See Grayscale.
Surface Clutter: Surface Clutter is a phenomenon where sonar returns are
reflected off of tiny objects near the surface of the water, including algae and even
126
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
Sonar Terms
GPS & Navigation Terms
Transducer: The transducer is part of the sonar system, which mounts on the boat
and is in contact with the water, that converts the electrical energy from the
transmitter into sound energy, and that forms the sonar beam in turn. Internally,
the transducer consists of one or more piezo electric disks that expand by very
minute amounts to create the sound wave. This element also works in reverse,
converting the returned sound energy back into an electrical signal that the receiver
interprets. Transducers are available for many specific mounting applications for the
boat, such as a transom mount, trolling motor mount, etc. Humminbird® offers
many sophisticated transducers, often with multiple piezo electric elements
designed to form specifically-shaped sonar beams, providing the angler with
superior tools for finding and catching fish. See Transmitter and SONAR.
TrueArch®: TrueArch® is a Humminbird® feature that provides true fish arches, not
artificial arches or symbols. Humminbird® units are capable of producing fish arches
due to the wide 60° sonar beam of DualBeam PLUS™, an extremely sensitive sonar
receiver. See Fish Arch.
Viewing Angle: Viewing Angle is an attribute of an LCD that characterizes visibility
of the display when viewing from off the central access, such as when standing to
the side of the fishfinder. Wider viewing angles are better because the information
remains visible even when viewing from the side.
WhiteLine®: WhiteLine® is a Humminbird® feature that highlights the strongest
sonar return on the display using a very light gray band. This is preferred by some
anglers who have grown accustomed to the feature on paper graph chart recorders.
Transmitter: The transmitter and receiver are matched parts of the sonar system
that send (transmit) and listen to (receive) the sonar signals, and work in
conjunction with the transducer. Humminbird® transmitters have an extremely
fast cycling design that can send signals up to 60 times per second, as well as
produce the varying levels of power output needed for different depths and
conditions. Additionally, the transmitter has the capability to create very precise
sonar pulses needed for a high degree of target separation. Humminbird®
receivers are extremely sensitive, but within a narrow "bandwidth" to
discriminate against noise from external sources. Additionally, the receiver offers
a wide "dynamic range" which provides the ability to receive very strong signals
alternating with very weak signals, without the strong signal overwhelming the
weak signal. See Transducer and Noise.
WideSide®: WideSide® is a Humminbird® sonar configuration used in an optional
transducer. WideSide® uses three sonar beams pointing to the left, right and down.
Beams pointing to the left and right are effective for spotting fish and structure near
the surface or on the bank. The downlooking beam provides depth information
directly below the boat.
X-Press™ Menu: X-Press™ Menus are a Humminbird® feature that make the most
commonly-used menu selections available with one press of the MENU key. Items
that appear on the X-Press™ Menu are related to the current view, and present the
most logical choices for that view. Sonar View X-Press™ menus will differ from
Chart View X-Press™ menus, etc. X-Press™ menus are one of the principal reasons
that Humminbird® products are easier to use.
TripLog: TripLog is a Humminbird® feature that provides an on-screen counter for
Elapsed Time, Average Speed and Total Distance traveled, and requires a speed
input to activate the feature. TripLog appears on the Big Digits View, and can be
reset to zero through the TripLog menu.
127
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
GPS & Navigation Terms
Zoom: Zoom is a feature that focuses in on a smaller area of the bottom to provide
enhanced resolution. With enhanced resolution, the angler can more easily see fish
hanging in structure or multiple fish hanging close together. Split screen zoom
divides the display into the full range view on the right, and the zoomed view on the
left. Humminbird® offers One-Touch® Zoom which allows the zoom feature to be
easily accessed from the regular sonar view with just one key press, eliminating the
need to use menus to access the feature.
Acquisition Time: The length of time that a GPS receiver typically takes to
determine a position from at least three satellites. Humminbird® GPS receivers
provide very fast acquisition times (under one minute), permitting users to get
out on the water faster.
Alarm, Arrival: The audible alert that sounds when the boat is equal to or less
than the alarm setting (25 feet – 3000 feet) from the location of the destination
waypoint.
Zoom, Bottom Lock: Bottom Lock Zoom is a feature that focuses on a smaller area
just above the bottom to provide enhanced resolution. Unlike regular zoom, it
continuously graphs the bottom at a constant point on the display regardless of
changes in depth. This "flattens" out the bottom contour, but is effective at showing
fish on or near the bottom, and is preferred by many saltwater anglers.
Alarm, Drift: Drift Alarm is an audible alert that sounds when the boat is equal
to or over the alarm setting (25 feet – 3000 feet) from the location where the
alarm was turned on.
Alarm, Off-Course: Off-Course Alarm is an audible alert that sounds when the
boat’s distance from the intended Track, (Cross Track Error), is equal to or over
the alarm setting (25 feet – 3000 feet). See Track and Cross Track Error.
Altitude: Altitude measures height above sea level. Altitude is a measurement
that can be provided by GPS.
Bearing (BRG): Bearing is the direction to a destination waypoint measured in
degrees from North (i.e. 321°, where 000° is North, 090° East, 180° is South,
270° is West).
Chartplotter: Chartplotter describes a navigation device that shows Present
Position on a Map, along with Tracks, Waypoints, and Routes. All Chartplotters
are also considered Trackplotters. All Humminbird® GPS Combo units are
Chartplotters. See Trackplotter.
128
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
GPS & Navigation Terms
Cold Start: Cold Start refers to the procedure that a GPS receiver must perform
when it does not have historical information regarding its current location. This
procedure typically lasts for several minutes, and may be experienced upon first
power up of the receiver, or if the receiver has been moved a great distance.
Estimated Position Error (EPE): Estimated Position Error is a calculation that
indicates the potential position inaccuracy the user may experience due to a
variety of GPS factors which include satellite position in the sky, signal strength
and others factors.
Course Over Ground (COG): Course Over Ground is the current direction the
boat is traveling measured in degrees from North (i.e. 321°, where 000° is North,
090° East, 180° is South, 270° is West). When the Course Over Ground is equal
to Bearing, the boat is said to be “On Course” and will arrive at the destination
in the most efficient manner. COG is often confused with Heading. See Heading.
Fix Type: Fix Type indicates whether the GPS receiver is providing 2D fix or 3D
fix. A 2D fix requires only three satellites and provides only latitude and
longitude. A 3D fix requires four or more satellites, and provides latitude,
longitude and altitude.
GPS: GPS is an acronym for Global Positioning System. GPS provides accurate
position (latitude, longitude, altitude) information virtually anywhere on the
earth through satellite technology and personal receivers on the ground. A series
of geosynchronous satellites broadcast a unique signal toward the earth once
per second. A GPS receiver, such as that included with many Humminbird®
products, receives the signals from these satellites and is able to determine
position based on very slight differences in the time each signal is received and
the receiver’s knowledge of the location of each of the satellites.
Cross Track Error (XTE): Cross Track Error is the straight-line distance of the boat
from the intended Track. XTE measures how far the boat is off course, and also
triggers the Off Course Alarm. See Track.
Differential GPS (DGPS): Differential GPS is a system to improve the position
accuracy of the Department of Defense GPS through the use of secondary
“correction signals” broadcast from ground stations around the coastal United
States and on some inland waterways. These correction signals are provided by
the USCG and received by an auxiliary Differential Beacon Receiver (DBR) that
connects to the GPS receiver. The advent of WAAS has largely negated the need
for the added expense of a DBR in the United States.
Heading: Heading describes the direction the boat is pointing and is measured
in degrees (i.e. 321°, where 000° is North, 090° East, 180° is South, 270° is
West). Due to wind and waves, the boat is often traveling in a slightly different
direction than it is heading, and therefore Heading is often confused with Course
Over Ground. See Course Over Ground.
Distance To Go: Distance To Go is the straight-line distance between Present
Position and the Destination Waypoint. DTG and SOG (Speed Over Ground) are
used to calculate Time To Go. See Time to Go and Speed Over Ground.
Map Datum: A Map Datum refers to a particular survey of the earth’s surface
that was referenced when creating a chart (i.e. WGS84). Since the earth is not
flat, and not even consistently round, a mathematical model must be used to
translate coordinates from the sphere of the earth to the flat surface of a chart.
129
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
GPS & Navigation Terms
This mathematical model is the Map Datum. Historically, many different Map
Datums have been used around the world to create maps; often a reference to
the Map Datum can be found in the legend of a paper map. It is important to
select the correct Map Datum setting in your fishfinder when comparing GPS
position to a paper chart to avoid slight position inaccuracies. Almost all
electronic charts use the WGS84 Map Datum and therefore, they do not require
setting changes.
Present Position: Present Position is the current location (latitude, longitude)
determined by GPS. The Present Position is indicated on-screen by a directional
boat icon if the boat is moving, or a round symbol if the boat is stationary.
Route: A Route is series of waypoints linked together in a specific sequence to
define a navigation path between two points, and saved in the fishfinder’s
memory. Routes are often used when frequently traveling between two or more
locations because it is a faster and more accurate method than repeatedly
selecting individual waypoints each time one travels through the same area.
Routes consist of a Start Waypoint, an End Waypoint, and a series of waypoints
in between. Users can begin navigation at the beginning, the end (to run the
route in reverse) or at any waypoint in between. See Waypoint.
MMC: MMC is an acronym for Multi Media Card. An MMC is a postage stamp-
sized memory device used to store electronic data such a maps, waypoints,
routes and other information. MMC is a very rugged format suitable for the
marine environment, but it is not waterproof. The MMC is removable from
Humminbird® products, and can be used in a PC that is equipped with an
appropriate card reader. MMC is the same format that many digital cameras use.
See SD.
SD: SD is an acronym for Secure Digital. An SD card is virtually identical in
function to an MMC; however, the speed at which information can be accessed
is generally faster, the storage capacity is generally larger, and the card has
security features which can be used to prevent extracting the data from the card.
SD is the same format that many digital cameras use. See MMC.
North, Magnetic: North is the principle reference point of the compass (i.e.
North is 000°). Magnetic North relies on the earth’s magnetic field to align a
metal pointer generally towards True North. However, due to local variations in
the earth’s magnetic field around the globe, the difference between True North
and Magnetic North can be greater than 10°. See True North.
Selective Availability: Selective Availability (SA) is a GPS system “feature” that
can be implemented by the U.S. Department of Defense (DoD) to degrade the
accuracy of GPS positioning information. With SA active, the GPS is accurate to
within 100 meters 95% of the time. With SA inactive, the GPS is accurate to
within 45 meters 95% of the time. Currently, SA is inactive and the consumer can
enjoy the greater precision GPS provides; however, the DoD reserves the right to
activate SA at any time.
North, True: North is the principle reference point of the compass (i.e. North is
000°). True North uses the axis of the rotation of the earth as the reference for
North and is constant for all points on the earth. Most GPS units default to True
North as the setting. The GPS heading may vary from the boat compass heading
because the compass uses Magnetic North. Humminbird® GPS units provide the
option of selecting True or Magnetic readouts by using the North Reference
menu. See Magnetic North.
130
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
GPS & Navigation Terms
Speed Over Ground (SOG): Speed Over Ground is the measurement of the
boat’s progress across a given distance, and is the speed measurement provided
by GPS. An alternate, Speed Through Water, is provided by a speed
paddlewheel, and is the measurement of the flow past the boat, which may vary
depending on current speed and direction. Speed Over Ground is optimal for
navigation because accurate destination times can be derived from this
measurement. Humminbird® products allow for input and display of both speed
measurements.
Trackplotter: Trackplotter describes a navigation device that shows Present
Position, along with Track, Waypoint, and Routes, but NO MAP in the
background. See Chartplotter.
Trolling Grid: Trolling Grid is a Humminbird® feature that displays a precise
reference grid around a waypoint. This grid is used as a guide pattern for trolling
around a specific area to assure a more efficient and complete coverage of that
area. Trolling Grid resolution be changed by zooming in or out on the chart. The
Trolling Grid can also be rotated on the display to orient it for optimal boat course
for wave and wind conditions.
Time To Go (TTG): Time To Go is the estimated time required to reach the
destination waypoint. TTG is calculated using the SOG and DTG. See SOG and DTG.
UTC: UTC is an acronym for Universal Time Constant. UTC is the “standard time”
used in navigation, and is the local time in Greenwich England. (UTC is
equivalent to Greenwich Mean Time (GMT)). To display the correct Local Time in
a Humminbird® GPS unit, the user must use the Local Time Zone menu and
select the time zone (i.e. EST, CST).
Track: A Track is a series of saved points that define the past path of the boat.
These Track Points are saved at regular time intervals. Tracks are a useful and
quick method to see where you’ve been, and an easy guide to follow to get you
back to the starting point. Generally, all GPS units have a limited number of Track
Points that can be saved before the unit runs out of memory and begins erasing
the first track points saved. Because of this, the user can adjust the Track Point
Interval menu to increase the amount of time between when points are saved,
and thus extend the distance covered by a track. Tracks can also be permanently
saved to memory, and re-displayed at the user’s option.
WAAS: WAAS is an acronym for Wide Area Augmentation System. WAAS is
complementary technology to GPS that provides enhanced accuracy through
correction signals broadcast from Federal Aviation Administration WAAS
satellites stationed over the USA. These secondary signals are automatically
received by the standard Humminbird® GPS Receiver. With WAAS signal, GPS
accuracy is improved to within 3 meters 95% of the time. Outside the United
States, regional governmental coalitions have created similar systems such as
EGNOS (Europe) and MSAS (Japan).
Track Line (TRK): The Track Line is the desired line of travel between two
waypoints, and represents the most efficient path between the two points
because it is a straight line. The TRK is measured in degrees (i.e. 321°, where
000° is North, 090° East, 180° is South, 270° is West). See Cross Track Error
and Course Over Ground.
131
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
GPS & Navigation Terms
Waypoint: A Waypoint is the saved location (latitude, longitude) of a point of
interest that is stored in a GPS receiver’s memory. This can include a marker
buoy, dock, fishing hole or anywhere else the user may want to return to.
Humminbird® products offer the ability to name and assign a symbol to the
saved location. Depth, Date and Time of Day when the waypoint was created is
also saved.
Waypoint Target: Waypoint Target is a Humminbird® feature that displays a
precise “bull’s eye” around a selected waypoint. This bull’s eye is used to easily
monitor boat position relative to a waypoint, and is useful for fishing over
submerged structure. With Waypoint Targets, a quick look at the screen lets you
know how far off the waypoint the boat has drifted.
132
Download from Www.Somanuals.com. All Manuals Search And Download.
Contact Humminbird®
Contact the Humminbird® Customer Resource Center
in any of the following ways:
By Telephone
(Monday - Friday 8:00 a.m. to 4:30 p.m. Central Standard Time):
1-800-633-1468
By e-mail
(typically we respond to your e-mail within three business days):
custserv@johnsonoutdoors.com
For direct shipping, our address is:
Humminbird®
Service Department
678 Humminbird Lane
Eufaula, AL 36027 USA
133
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Grundig CRT Television 19 VLC 2000 T User Manual
Harbor Freight Tools Outboard Motor 41108 User Manual
Healthrider Treadmill HRT99020 User Manual
Honeywell Security Camera HD73 User Manual
HP Hewlett Packard DVD Recorder 447328 B21 User Manual
Hunter Fan Fan 20510 User Manual
Hunter Fan Outdoor Ceiling Fan 42444 01 User Manual
IBM Computer Drive 7214 User Manual
IBM Personal Computer 6584 User Manual
IBM Printer 1NA User Manual