Portable System
Owners Manual
Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
Adult Assembly Required.
This manual, accompanied by sales receipt, should be saved and kept on hand as a convenient reference, as it
contains important information about your model.
REQUIRED TOOLS AND MATERIALS:
WARNING!
• Garden Hose or Sand
• 2 Capable Adults
• (2 each) Wrenches
READ AND UNDERSTAND
OPERATOR'S MANUAL
BEFORE USING THIS UNIT.
• Tape Measure
1/2"
9/16"
AND/OR
(2) Socket Wrenches and Sockets
3/4"
FAILURE TO FOLLOW
OPERATING
INSTRUCTIONS COULD
RESULT IN INJURY OR
DAMAGE TO PROPERTY.
• Wood Board (scrap)
• Sawhorse or Support Table
• Hammer
Write Model Number
From Box Here:
1/2"
9/16"
3/4"
• Optional: Large & Small
Adjustable Wrenches
• Extension
• Step Ladder 8 ft. (2.4m)
• Safety Glasses
• Phillips-Head Screwdriver
Toll-Free Customer Service Number for U.S: 1-800-558-5234,
For Canada: 1-800-284-8339,
For Europe: 00 800 555 85234 (Sweden: 009 555 85234),
For Australia: 1-800-632 792
Internet Address: www.huffysports.com
© COPYRIGHT 2006 by SPALDING
1
12/06
ID# M6809011
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR
PROPERTY DAMAGE AND WILL VOID WARRANTY.
Owner must ensure that all players know and follow these rules for safe operation of the system.
To ensure safety, do not attempt to assemble this system without following the instructions carefully. Check
entire box and inside all packing material for parts and/or additional instruction material. Before beginning
assembly, read the instructions and identify parts using the hardware identifier and parts list in this document.
Proper and complete assembly, use, and supervision are essential for proper operation and to reduce the risk
of accident or injury. A high probability of serious injury exists if this system is not installed, maintained, and
operated properly.
• If using a ladder during assembly, use extreme caution.
• Check base regularly for leakage. Slow leaks could cause the system to tip
over unexpectedly
• Seat the pole sections properly (if applicable). Failure to do so could allow the
pole sections to separate during play and/or during transport of the system.
• Climate, corrosion or misuse could result in system failure.
• If technical assistance is required, contact Customer Service.
• Minimum operational height is 6'-6" (1.98m) to the bottom of backboard.
Most injuries are caused by misuse and/or not following instructions.
Use caution when using this unit.
PRODUCT REGISTRATION:
Please remember to complete your product registration form on-
line at:
IMPORTANT!
Remove all contents from boxes.
Be sure to check inside pole sections,
hardware and additional parts are packed inside.
WARNING!
IF YOUR SYSTEM IS EQUIPPED WITH AN ACRYLIC BACKBOARD, EXAMINE BACKBOARD FOR ANY DAMAGE
THAT MAY HAVE OCCURRED DURING SHIPMENT. CRACKS IN THE BACKBOARD COULD RESULT IN
SUDDEN BREAKAGE. IF BACKBOARD IS DAMAGED IN ANY WAY PRIOR TO OR AFTER ASSEMBLY, CALL
TOLL-FREE NUMBER:
3
12/06
ID# M6809011
Download from Www.Somanuals.com. All Manuals Search And Download.
Get to know the basic parts of your basketball system...
FRONT
BACK
BACKBOARD
RIM
ELEVATOR ASSEMBLY
TOP POLE
MIDDLE POLE
BASE
BOTTOM POLE
STRUTS
WHEEL CARRIAGE ASSEMBLY
4
ID# M6809011
12/06
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST - See Hardware Identifier
Item Qty. Part No. Description
Item Qty. Part No. Description
1
2
3
4
5
6
7
8
1
2
1
1
1
1
2
2
1
2
1
1
2
8
1
2
1
6
1
1
1
1
4
600053
906410
800344
Tank
28
29
30
31
32
33
1
3
8
7
2
1
908355
205678
201651
206340
908412
568090
Cover Plate, Rim
Strut, Pole to Base
Screw Jack Assembly
Bolt, Hex Head, 1/2-13 x 7 Long
Spacer, Plastic, .530 I.D. x .25 Long
Lock Nut, Hex 1/2-13
Elevator Tube, Lower - Long
Label, Height Adjustment and Moving
FR908402 Top Pole Section
FR908401 Middle Pole Section
FR908403 Bottom Pole Section
800332
600056
108306
203099
600062
202662
206938
203100
908415
204846
600058
203153
108181
201518
700009
202528
205679
Wheel Bracket
Wheel, 3.5”
Rod, Axle
Nut, Ny-lock, 5/16-18
Cap, Cover, Height Indicator
Bolt, Hex Head, 5/16-18 x 4-1/2 Long
Pushnut, 7/16 Shaft Diameter
Hex Flange Nut 5/16-18
Bracket, Pole Mount
Carriage Bolt, 5/16-18 x 4.5 Long
Cover, Upper Tube
Bolt, Hex Head, 5/16-18 x .75 Long
Plate, Pole Mounting
Bolt, Hex Head, 5/16-18 x 2.75 Long
Handle, Elevator Assembly
Pin, Actuator Assembly
Bolt, Hex Head, 1/2-13 x 2 Long
Washer, Flat, 5/16
Bolt, Hex Head, 3/8-16 x 2 Long
Bolt, Hex Head, 5/16-18 x 2 Long
Plate
FR568090 Label, French
Rim
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
1
2
2
1
1
2
2
1
1
1
1
1
1
1
1
2
9
908411
202587
203470
600052
204558
205528
600049
206989
Elevator Tube, Upper - Short
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Spacer, .530 I.D. x 1” Long
Washer, Flat, .625 I.D. x .1.5 O.D.
Cap, Pole Top
Screw, 1/4 x .375 Long
Bolt, Hex Flange, 5/16-18 x 1 Long
Cap, Base
Reinforcement Bracket
Net
Bracket, Slam Jam
Bolt, Tee, 3/8-16, 5” Long
Bracket, Reinforcement, Slam Jam
Spring, Rim
Nut, Special, 3/8-16
Washer, Flat, .344 I.D. x .1.5 O.D.
900033
203796
200318
203472
203795
205842
8* 203218
2
4
1
203679
203104
908416
* YOU MAY HAVE EXTRA PARTS WITH THIS MODEL.
NOTE
Hardware kit is designed for more than one
style of basketball system. Not all hardware
will be used.
5
12/06
ID# M6809011
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE IDENTIFIER (BOLTS & SCREWS)
#29 (3)
#12 (1)
#39 (2)
#20 (1)
#25 (2)
#26 (4)
#40 (2)
#23 (4)
#45 (1)
#16 (2)
#18 (6)
HARDWARE IDENTIFIER (NUTS & WASHERS)
#10 (2)
#14 (8)
#31 (7)
#48 (1)
#24 (8)*
#37 (1)
#49 (2)
* You may have extra parts with this model.
6
ID# M6809011
12/06
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE IDENTIFIER (PLASTIC SPACERS CAPS & CLIPS)
#36 (2)
#30 (8)
#13 (4)
HARDWARE IDENTIFIER (OTHER)
#47 (1)
#44 (1)
#46 (1)
7
12/06
ID# M6809011
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION A: ASSEMBLE THE BASE
TOOLS REQUIRED FOR THIS SECTION
This is what your system will look like when
you’ve finished this section.
(2) Wrenches
9/16”, 1/2”
AND/OR
Sawhorse or
support table
(2) Socket Wrenches and Sockets
Extension
1/2”
9/16”
Complete wheel assembly as shown in Figure A. Secure wheel bracket (7) and wheel assembly (Fig. A.)
to the tank (1) with a bolts (18) and washers (24). Repeat procedure for opposite wheel.
1.
NOTE:
TO INSTALL SECOND
PUSHNUT:
Fig. A.
1
• Assemble Pushnut,
Wheels, Axle, And
Wheel Bracket As
Shown.
• Support Pushnut/Axle
From The End With A
Block Of Wood To
Install The Second
Pushnut Onto The
Axle.
18
18
24
18
Wood Block
24
18
24
24
13
13
7
7
9
8
8
8
ID# M6809011
12/06
Download from Www.Somanuals.com. All Manuals Search And Download.
Correctly identify each pole section. Poles have an identification sticker that will be used as a
reference point in the next step.
2.
MIDDLE
5
IDENTIFICATION STICKER
IDENTIFICATION STICKER
6
4
BOTTOM
TOP
Bounce middle pole section (5) into top section (4) using a wood scrap as shown until the top pole no
longer moves toward the pole identification sticker on the middle pole.
3.
5
CAUTION!
IMPORTANT!
THE IDENTIFICATION STICKER IS
LOCATED 5" FROM THE END OF
THE POLE. WHEN PROPERLY
POUNDED TOGETHER, THE POLE
SECTIONS SHOULD HAVE A 4-1/2"
MINIMUM OVERLAP, LEAVING 1/2"
BETWEEN THE OVERLAPPING POLE
AND THE IDENTIFICATION STICKER.
NOTE ORIENTATION OF
POLES.
4
Wood Scrap (not supplied)
9
12/06
ID# M6809011
Download from Www.Somanuals.com. All Manuals Search And Download.
Attach pole assembly to tank (1) as shown.
Secure pole assembly to tank using
bolts (25) and pole mounting plate (19) as
shown.
Bounce top and middle pole assembly (4 and 5)
onto bottom pole section (6) using a wood scrap as
shown. Bounce until the top and middle pole
assembly no longer moves toward the pole
identification mark on the bottom pole.
4.
5.
WARNING!
TWO CAPABLE ADULTS
IMPORTANT!
REQUIRED FOR THIS
PROCEDURE. FAILURE TO
FOLLOW THIS WARNING COULD
RESULT IN SERIOUS INJURY
AND/OR PROPERTY DAMAGE.
NOTE ORIENTATION.
4
6
5
6
19
25
Wood Scrap
(not supplied)
10
ID# M6809011
12/06
Download from Www.Somanuals.com. All Manuals Search And Download.
Secure tank struts (2) to pole as shown.
6.
WARNING!
TWO CAPABLE ADULTS
REQUIRED FOR THIS
PROCEDURE. FAILURE TO
FOLLOW THIS WARNING COULD
RESULT IN SERIOUS INJURY
AND/OR PROPERTY DAMAGE.
IMPORTANT!
DO NOT TIGHTEN
COMPLETELY.
2
2
10
12
11
12/06
ID# M6809011
Download from Www.Somanuals.com. All Manuals Search And Download.
Rotate non-secured ends of tank struts (2) outward to
mounting holes in tank as shown. Secure non-secured ends
of tank struts (2) to tank as shown. Repeat for opposite
7.
WARNING!
TWO CAPABLE ADULTS
REQUIRED FOR THIS
side.
PROCEDURE. FAILURE TO
FOLLOW THIS WARNING COULD
RESULT IN SERIOUS INJURY
AND/OR PROPERTY DAMAGE.
2
2
2
40
24
40
24
2
49
14
49
14
IMPORTANT!
DO NOT TIGHTEN
COMPLETELY.
IMPORTANT!
Struts MUST be attached to
the base through the
LARGER holes.
Install pole mount bracket (15) and
reinforcement bracket (42) with carriage bolts
(16) as shown. Tighten flange nuts (14)
completely.
14
8.
6
IMPORTANT!
15
42
DO NOT OVER
TIGHTEN!
16
IMPORTANT!
TIGHTEN ALL HARDWARE
FROM STEPS 6-8 AFTER THIS
ASSEMBLY IS COMPLETED.
12
ID# M6809011
12/06
Download from Www.Somanuals.com. All Manuals Search And Download.
Securely rest the assembly on sawhorse. Identify elevator
tubes (32 and 35).
Toward Pole
9.
35
32
Lower Elevator tube
32
Upper Elevator tube
WARNING!
35
TWO CAPABLE ADULTS
REQUIRED FOR THIS
PROCEDURE. FAILURE TO
FOLLOW THIS WARNING COULD
RESULT IN SERIOUS INJURY
AND/OR PROPERTY DAMAGE.
Toward Board
While the system is securely resting on the sawhorse. Install elevator tubes (32 and 35) to top pole
section (4) as shown. Install pole cap (38) at this time.
10.
COMPLETED ASSEMBLY
29
29
38
35
30
30
4
30
WARNING!
30
32
31
35
31
TIGHTEN BOLT (29) IN
LOCK NUT (31) UNTIL
FLUSH (EVEN) WITH LOCK
NUT’S OUTER EDGE.
32
13
12/06
ID# M6809011
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION B: ATTACH THE BACKBOARD
TOOLS REQUIRED FOR THIS SECTION
This is what your system will look like when you’ve
finished this section.
(2) Wrenches
9/16”, 1/2”, 3/4”
AND/OR
(2) Socket Wrenches and Sockets
Extension
1/2” 9/16” 3/4”
Phillips Screwdriver
Sawhorse or support table
While still supported on sawhorse. Attach elevator tubes (32) to backboard using spacers (30), bolts
(23), and nuts (31) as shown.
1.
23
23
30
30
31
31
31
31
30
30
23
23
14
ID# M6809011
12/06
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT!
Carefully cut and
peel protective film
away from board
prior to attaching
rim.
Insert T-bolt (45) into Slam Jam bracket (44) then, attach that assembly to board using
bolts (26) and nuts (14).
2.
14
27
45
44
26
15
12/06
ID# M6809011
Download from Www.Somanuals.com. All Manuals Search And Download.
Install Slam Jam Rim to Backboard
3.
A. Fit rim (34) securely into bracket (44) as shown. Allow T-bolt (45) to slip through center
hole in rim (34).
B. Install reinforcement bracket (46) onto T-bolt (45) as shown.
C. Install spring (47) onto T-bolt (45) as shown.
D. Install special nut (48) and washer (37) onto T-bolt (45).
E. Tighten nut (48) until flush with end of T-bolt (45).
NOTE:
ORIENTATION
OF BRACKET
46
B
A
46
45
34
45
44
37
48
C
D
47
45
37
45
48
E
16
ID# M6809011
12/06
Download from Www.Somanuals.com. All Manuals Search And Download.
Place cover (17) onto screw-jack assembly (3). Install cap (11).
4.
A.
11
17
3
Install handle assembly (3, 17 and 11) to lower elevator tubes (32) using bolt (29), spacers (36),
and nut (31) as shown.
B.
29
36
36
32
3
4
31
32
IMPORTANT!
Note orientation of handle.
WARNING!
TIGHTEN BOLT (29) IN
LOCK NUT (31) UNTIL
FLUSH (EVEN) WITH LOCK
NUT’S OUTER EDGE.
17
12/06
ID# M6809011
Download from Www.Somanuals.com. All Manuals Search And Download.
5.
Secure the handle assembly (3, 17 and 11) to pole bracket (15) using bolt (20) and nut (10) as shown.
NOTE:
Before going on to next
step, set adjustable system
assembly to the 10’ (3.05 m)
setting.
3
21
20
22
10
15
WARNING!
TIGHTEN BOLT (20) IN
LOCK NUT (10) UNTIL
FLUSH (EVEN) WITH LOCK
NUT’S OUTER EDGE.
18
ID# M6809011
12/06
Download from Www.Somanuals.com. All Manuals Search And Download.
Roll completed assembly to desired position. Fill tank with water (approx. 40 gallons (128 Liters)) or
sand (approx. 475 lbs. (216 kg)) and rotate the cap (41) into base (1).
6.
WARNING!
TWO CAPABLE ADULTS
REQUIRED FOR THIS
PROCEDURE. FAILURE TO
FOLLOW THIS WARNING
COULD RESULT IN SERIOUS
INJURY AND/OR PROPERTY
DAMAGE.
DO NOT LEAVE ASSEMBLY
UNATTENDED WHEN EMPTY;
IT MAY TIP OVER.
41
CAUTION!
ADD TWO GALLONS (7.6
LITERS) OF NON-TOXIC
ANTIFREEZE IN SUB-
FREEZING CLIMATES.
1
IF USING SAND: 2 GALLONS
OF ANTI-FREEZE IS NOT
REQUIRED.
WARNING!
Cap (41) MUST be tightened COMPLETELY and
SECURELY to prevent leakage.
CHECK WATER LEVEL BEFORE EACH USE!
FAILURE TO FOLLOW THIS WARNING COULD
RESULT IN SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
19
12/06
ID# M6809011
Download from Www.Somanuals.com. All Manuals Search And Download.
7.
D.
B.
C.
A.
Install
net (43).
43
43
34
34
Apply Height Adjustment and Moving Label (33) to front of
pole, where it is clearly visible.
HEIGHT
ADJUSTMENT
handle to raise
and lower
backboard.
8.
Rotate crank
Do not over crank
handle beyond the
manufactured height
indicator range of
7-1/2 - 10 feet.
Damage may be
caused to the screw
jack’s internal
adjustment
mechanism if
adjusted over 10 or
under 7-1/2 feet.
A
CAUTION!
B
DO NOT OVER-CRANK HANDLE
BEYOND THE MANUFACTURED
HEIGHT-INDICATOR RANGE OF
MOVING SYSTEM
1. While holding pole, rotate basketball sytem
forward until wheels engage with ground.
7-1/2 - 10 FEET. DAMAGE MAY
BE CAUSED TO THE SCREW
2. Move basketball system to desired location.
3. Carefully rotate basketball system upright.
4. Check system for stability.
A
JACK’S INTERNAL
ADJUSTMENT MECHANISM IF
ADJUSTED OVER 10 OR UNDER
7-1/2 FEET.
33
B
1
2
3
568090
11/06
HEIGHT AND MOVING LABEL
MUST NOT OBSTRUCT
FACTORY ATTACHED WARNING
LABEL.
NOTE:
Handle (21) can
be removed and
stored by
22
removing pin
(22).
21
RIM COVER ATTACHMENT
9.
39
NOTE:
34
Cover plate (28) will fit
INSIDE back bracket.
39
28
20
ID# M6809011
12/06
Download from Www.Somanuals.com. All Manuals Search And Download.
|