Contents
WASHING MACHINE
Description, 3
Installation, 4-7
Unpacking and levelling
Remove the transit fixings
Location
Levelling
Water connection
Drainage connection
Electrical connection
Before you start using your machine
Control Panel Features, 8
Programmes and Option Modifiers, 9-13
Starting a programme
ProgrammeTable
Option modifiers
Special features
Automatic features
Detergents, 14
Detergent dispenser
Washcare tips
Care and Maintenance, 15
Cleaning your machine
Fuses
Changing the plug
Cleaning the pump
Precautions and Advice, 16-17
General safety
Saving energy and respecting the environment
Disposal
Safety advice
Technical details chart
Something wrong? - Troubleshooting, 18-19
Service, 20
Before calling for Assistance
Spare parts
Key Contacts
! Keep this instruction book on hand in order to refer to it when necessary. Take it with you when you move,
and should you sell this appliance or pass it on to another party, make sure that this booklet is supplied
along with the appliance so that the new owner may be informed about warnings and suggestions on how
the machine works.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Description
GB
Control panel
(
•
Varies by Model)
Dispenser drawer
• Please record the Model number
and Serial number of your machine
on the back cover of this book for
future reference.
• The Serial number can be found
on the inside door trim.
Interlocking door
and release lever
Drainage hose
Cold water inlet points
Mains cable
Hooked end support
Plumbing indicator line
Plastic cover
Two transit fixings.
(see arrows)
Comprising of: two bolts, two
washers, two rubber grommets
and two spacers.
! BOTH transit fixings must be
removed BEFORE you use your
machine (see page 5)
Rating plate
Back feet
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
4. Remove the
polystyrene base.
GB
! Read these instructions carefully: the following
pages contain important information on installation
and suggestions on how the appliance works
Unpacking
1. Using scissors, cut
carefully along one corner
post to remove the film.
! This is the part of the
polystyrene base and
should have stayed intact
when you removed the
base.
! If it has broken off and
is still in the machineꢀ
remove itꢀ while the
machine is still laying on
its side on the top cap.
! IMPORTANT check
when unpacking your
machine:
2. Lift off the polystyrene
top cap and remove the
corner posts.
5. Stand the machine
upright.
! We recommend that a
second person helps to
raise and lower the
machine.
3. Carefully lay the left
side of the machine
down onto the top cap.
! Continue to read the rest
of these instructions
! We recommend that a
second person helps to raise
and lower the machine.
carefully; the following
pages contain important
information on installation
and troubleshooting.
! Protect the environment - please dispose of the
packaging material carefully and considerately.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
3. Hold, slide sideways and pull to
remove.
Remove the transit fixings
GB
IMPORTANT: Follow these instructions to remove the
TWO transit fixings (see Description for location).
! Situated on either
side of the rear
panel,
BOTH transit bolts
MUST be removed
before use.
4. For safety, insert both
yellow plastic covers
(supplied with your machine)
over the holes.
Location of transit bolts
(see arrows)
! Repeat steps 1 to 4 to remove the second transit bolt.
! Packaging materials are not children’s toys.
! Failure to do so may cause damage to your machine.
! It is important the transit fixings and spacers come out intact.
! Be sure to remove: TWO bolts,
TWO washers, TWO rubber
grommets and TWO nylon
spacers (see pic.)
Location
Where you install your machine will affect its
performance:
! For your safety and to comply with electrical
regulations, seek professional advice if you want to
install your machine in a bath or shower room.
1. Unscrew the bolt using a
13mm spanner
• Make sure that the electrical socket and water
taps are easily accessible. You should switch off
the machine's electrical and water supplies
when you are not using it for extended periods.
• Make sure that you allow enough space for the
machine. Select a space at least 60 cm wide,
60 cm deep and 85 cm high. Also leave enough
space to open the door fully, so that you can load
and unload it easily.
3. STOP when 3 threads can be
seen.
• Where possible, the machine should be positioned
on a solid floor to minimise vibration.
! Take care when you move the machine not to rip any
floor coverings. The weight of the machine may cause
indentations in some floor coverings.
Did you know?
•
ꢀthe transit fixings are fitted to ensure that your machine is undamaged during delivery.
•
ꢀboth of the transit fixings MUST BE removed before using the machine, be sure to remove TWO
bolts, TWO washers, TWO rubber grommets and TWO nylon spacers, not doing so will lead to
excessive vibration, movement of the machine and could eventually lead to internal damage.
ꢀthe majority of problems with noisy machines are due to the transit fixings not being removed,
closely followed by the feet not being adjusted correctly to level the machine.
ꢀyou will be charged for a service engineers visit if a problem with your machine is caused by
incorrect installation or misuse.
•
•
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Levelling
GB
Your machine will be noisy if the two front feet are not
adjusted so that the machine stands firm and level.
We recofitting a 3/4”sealing cap to
the hot water supply tap (if present),
to ensure there are no leaks. Sealing
caps can be purchased from
! The machine should be levelled from side to side
and from front to back.
Hotpoint Service on 08709 077 077
or all good DIY and Plumbing outlets.
1. Move your machine into its final location, talking
care not to trap or kink the hoses.
2.Turn one or both front feet
counter-clockwise by hand until
the feet cannot be turned any more.
When adjusting the feet, use a
spirit level to check the
Benefits of cold fill
• Modern detergents are designed to give the best
cleaning results at low temperatures. Biological
detergents contain enzymes which are active between
30 °C and 53 °C, giving greater results at lower
temperatures.
• Cold water relaxes fabrics, whilst hot water can
seal in stains.
• Improved stain removal with cold water.
• The most commonly used programme at present is
40 °C, which will take on cold water even if hot and
cold were available.
machine stands level, from side to
side and from front to back.
The spring on each foot will stop
them coming loose.
! If it is placed on a fitted or loose carpet, adjust the feet
in such a way as to allow enough room for ventilation
beneath the machine.
Water Connection
Connecting the water inlet hose supplied.
• You can heat the water required to finish the wash
cycle, which makes it more economical than taking
water heated in a tank by an immersion heater or
gas boiler.
Remember that this is a cold-fill machine and the
water inlet hose MUST be fitted to the rear of the
machine and the cold water supply. Please use the new
hose supplied (located inside the drum). Old hoses
may cause leasks due to worn out washers or may
split due to water pressure .
Hints and tips
! Make sure there are no kinks or bends in the hose.
! The water pressure at the supply tap must be within
the values indicated in the Technical Details table
(see page 17 ).
- Before making the connections to the cold water
supply, allow the water to run freely from the cold
water supply tap until it is completely clear.
- Connect the straight end to the hose connector to
the cold water supply tap
! If the water inlet hose is not long enough, you can
purchase an extended hose from Hotpoint Service on
08709 077 077.
! Always use a new inlet hose.
until tight.
! Check the water inlet hose at least once a year,
replace if cracked as worn hoses could split under
water pressure.
- Coonnect the angled end
of the hose to the
washing machine’s cold
water inlet point, situated
at the top right hand side
on the rear of the
!
Turn on the water supply and check that the
connections do not leak. If there is a leak, turn
off the water supply, disconnect the hoses and
check that the sealing washers are in place.
Refit the hoses and turn on the water supply.
appliance (see figure).
Turn the cold water supply tap on and check for leaks,
tighten if necessary.
Did you know?...
•
•
•
...the most common cause of problems with water connection is that the customer has not turned the
supply tap on.
...it is very important to ensure that your hoses or cables are not kinked or squashed when the machine is
pushed back into its location, as this can lead to your machine failing to fill or empty the water.
...the majority of problems with noisy machines are due to the feet not being adjusted correctly to
level the machine.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Drainage Connection
Electrical connections
GB
• Before plugging the appliance into the mains socket,
make sure that:
• the socket is earthed and in compliance with the
applicable law.
• the socket is able to sustain the appliances
maximum power load indicated in the Technical
Details table (see page 17 ).
• the supply voltage is included within the values
indicated in the Technical Details table ( see page 17 ).
• the socket is compatible with the machines plug.
If this is not the case,replace the socket or the
plug,ensuring a 13A fuse is fitted.
!Although you may need to move the hooked end
support along the grey drainage hose, DO NOT
remove it.
! Whichever drainage method you use,make sure
that the hooked end support is fixed level to, or
above the ‘Plumbing Indicator Line ’(see Description
page 3).
We recommend one of the following:
Standpipe method:
1. Make sure the standpipe
height is a minimum 500 mm
!The machine should not be installed in an outdoor
environment, not even when the area is sheltered,
because it may be very dangerous to leave it exposed
to rain and thunderstorms.
Hooked
end
support
up to a maximum 1200mm
from the floor.
50 cm min-
120 cm max
2. Insert the drainage hose
approximately 100mm into
the standpipe.
! When the machine is installed, the mains socket
must be within easy reach and should be connected
to a suitable electrical supply.
! Do not use extensions or multiple sockets.
!The power supply cable must never be bent or
dangerously compressed.
Under sink method:
! The power supply cable must only be replaced by an
authorised serviceman.
1. Cut off the blocked end
of the under sink
drainage unit,or remove
the blanking plug if
fitted.
!The company denies all liability if and when these
standards are not respected.
Before you start using your machine
The first wash cycle
Once the appliance has been installed and before you
use it for the first time, run a wash cycle without
detergent and no laundry. This will check your
installation,connections and drainage and will
thoroughly clean the interior before you carry out an
actual wash programme on your laundry.
2. Fix the hooked end
support a minimum of
800mm from the floor.
This will take approximately 2 1 /2 hours to complete.
3. Use a hose clip (e.g. a
jubilee clip) to securely
attach the grey drainage
hose end to the under
sink drainage unit.
Hose
clamp
!Run the 95 °White Cotton programme ‘2’, without
laundry and without detergent.
800 mm
! During this cycle check for any leaks from under the
machine. If present ensure all hoses are securely
tightened.
Installation
Did you know?...
• ...it is very important to ensure that your hoses or cables are not kinked or squashed as this can lead
to your machine failing to fill or empty the water.
• ...it is very important to respect the dimensions given within the drainage connection methods (see above).
• ...if using the undersink drainage method remember to cut off the blocked end, or remove the blanking plug.
• ...you will be charged for a service engineers visit if a problem with your machine is caused by
incorrect installation or misuse.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Control panel features
Ultima
GB
Programme listing
Option buttons
and lights
On/Off
button
Indicator
lights
Start/cancel
button
Digital
display
Detergent dispenser
drawer
Variable
Spin
Programme Selector
dial
Variable
Temperature
Ultima control panel features
• Programme listing: To consult a straight forward chart of the different programmes available.
• Option buttons: To select the options available ( see Programme Table and Option Modifiers ).
• Variable Temperature button: To reduce the selected programmes wash temperature .
• Variable Spin Speed button: To reduce the selected programmes spin speed .
• Digital display: Shows time remaining, wash temperature and spin speed for the selected programme.
• On/Off button: To turn the washing machine on and off.
• Start/Cancel button: To start. the programme or to cancel it, if incorrect settings were selected.
• Programme selector dial: To select the programme you require. The knob stays still during the cycle.
• Status indicator lights: Shows if the door is locked (when lit, the door cannot be opened) and the stage of
the programme that the machine has reached (wash, rinse or spin).
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Starting a Programme
8. In addition to showing you
Starting a typical wash programme
GB
the wash temperature and
spin speed for your selected
programme, the digital
display will show you the
time remaining until the end
of the programme.
1. Switch the machine on by
pressing the On/Off button.
- If ‘Time Delay’ option was selected the display will
show the remaining until the start of the wash
programme.
2. Sort your laundry into
groups by washcare labels.
Load the machine.
Close the machine door by
pushing it until it clicks.
9. StartIthe programme by pressing
the Start/Cancel button for
at least 3 seconds.
The ‘Door Locked‘ indicator will light up.
3. Add detergent and
fabric conditioner
to the dispenser drawer.
• To stop/change a programme once the machine
has started:
- Press the Start/Cancel button for 3 seconds.
- Select ‘Pump Out ’
dial.
on the Programme selector
! Refer to detergent
manufacturer’ s dosage
instructions.
• When the machine has finished emptying:
- Turn the Programme selector dial to the new
programme required (you may need to add
detergent).
- Press the Start/Cancel button to start the new
programme.
4. Turn the programme
selector dial to the
required programme.
10. During the programme,
the status indicator lights
will show you what stage
in the programme
5.Select any optional
wash feature(s)
the machine has reached
(wash, rinse, spin).
(see Option Modifiers ) you
require by pressing the
appropriate button(s).
-Indicator lights will show
what you have chosen.
11. A short time after the
programme has finished the
‘Door Locked‘ indicator will
go out and you can open the
machine door.
12. Switch the machine off by pressing the On/Off
button.
6. Reduce the programmes wash temperature:
- Press the Variable Temperature button, each press will
reduce the wash temperature by 5°C.
! Do not allow children to play with the machine or
tamper with the controls.
! Do not overload the machine. This may damage the
The new temperature will be shown in the display.
7. Reduce the programmes spin speed:
- Press the Variable Spin Speed button, each press will
reduce the spin spin speed.
laundry and reduce the quality of the wash.
ogrammesand OptionModifiers
The maximum load is 7 kg (Cotton).
Panel
! Do not try to open the dispenser drawer during
anyprogramme.
! Do not try to open the machine door when the ‘Door
Locked ’indicator is lit.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme table
Programmes Table * Programme setting fot test in accordance with IEC 60456 and EN 60456
GB
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Option Modifiers and
Special Features
Option modifiers
GB
! Not all options can be used on all programmes - (see Programme Table for option availability ).
• Wash Enhance:
Use this option to select a more intensive wash programme for the cotton 60 °C and cotton 40 °C for more
heavily soiled items. Additionally, use this option on the machine wash wool programme to select the special
Handwash wool programme for wool items that are not marked as machine washable. This cycle has been
approved by Woolmark for the Gold Care award.
• Reduced Creases:
Selecting this option will run the wash programme with a more gentle action and lower spin speed, in addition
to carrying out an additional rinse to ensure your laundry has fewer creases and will require less ironing.
• Rinse Hold:
Selecting this option will pause the cycle in the final rinse with the fabric conditioner keeping the laundry
fresh until you are ready to complete the programme. The Rinse Hold light will flash to indicate the cycle is
paused. The machine will stay in this state, tumbling the load occasionally until either the Start/Cancel button
is pressed or the Rinse Hold button is pressed again to continue the cycle.
• Mini Load:
Use this option for smaller loads less than the capacity listed for the material and programme type (see
Programmes Table ). This option reduces water consumption and washing time,saving energy when washing
smaller loads.
• Time Delay:
Use this option to delay the programme start by up to 24 hours. The display will show the delay chosen. Each press of
the button increases the Time Delay in increments of 1 hour. If you press the button again after 24 shows in the
display the machine will reset the Time Delay and show ‘OFF’ in the display, pressing the button after this will start
the Time Delay selection fron 1 hour. Once the countdown reaches zero the programme will start.
• Variable Temperature:
Use this option to reduce the wash temperature below the maximum for the programme you have chosen.
- each press of the button will reduce the wash temperature by 5°C. The new wash temperature will be shown in
the display. If you press again after ‘OFF’ has been displayed, the machine will revert to the original higher
temperature.
• Variable Spin Speed:
Use this option to reduce the spin speed below the maximum for the programme you have chosen.
- each press of the button will reduce the spin speed. The new spin speed will be shown in the display.
If you press again after ‘OFF’ has been displayed, the machine will revert to the original higher spin speed.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Option Modifiers and
Special Features
GB
Special features
GB
! Not all special features can be used on all programmes - (see Programme Table for option availability).
•
Fast Wash:
The Fast Wash programmes are designed for lightly soiled loads delivering quick results for smaller loads, using
less energy. For loads with stains or increased soil levels which require deeper cleaning, use the standard or
intensive wash cycles.
• Cool Wash: 30 °C
A low temperature wash which delivers cleaning results comparable to the intensive 40 °C cotton programme but
at a lower temperature for more colour sensitive garments and using less energy.
• Handwash:
A gentle action programme for delicate items and items labelled as hand wash only.
Not for Wool or Silk garments (use the special programmes for those materials).
• Handwash Wool Approved: (M0507)
The wool wash cycle on Hotpoint machines has been tested and approved by the Woolmark Company for washing
garments labelled as ‘hand wash ’, provided that the ‘garments ’are washed in accordance to the instructions
issued by the manufacturer of this machine.
This cycle is selected by turning the Programme Selector dial to the wool programme and selecting the ‘Wash
Enhance ’option modifier (see Programme Table and Option Modifiers ).
!
We recommend using a wool wash liquid when using Wool programmes.
• Digital Display
If time delay is selected this shows the time remaining until the start of the wash programme in hours - counting
down each hour.
It also displays time to end of the wash programme in hours and minutes counting down each minute.
! Please note time can go up as well as down depending on load absorbency, load size and water temperature.
Note: We recommend that if you use colour catcher sheets in your appliance that these only be used
inside a wash bag, as otherwise they can affect the performance of your machine.
Did you know?ꢀ
• ꢀwhen an option button is selected the corresponding light is illuminated.
ꢀif the option selected is incompatible with the programme selected, the button will flash and the
option will not be enabled.
• ꢀif you set an option that is incompatible with an option selected previously, only the last option
selected will be enabled.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Option Modifiers and
Special Features
Automatic features
GB
Unbalanced load detection
The machine has an inbuilt feature to prevent it from spinning too fast with an unbalanced load.
When an unbalanced load is detected, the machine will attempt to redistribute the load in order to
balance it evenly to achieve full spin speed.
If this is not possible and an unbalanced load remains the spin speed will be reduced, depending on the amount
of unbalance detected.This is to prevent the machine from damaging itself or its surroundings and to prevent
excessive noise from the machine.
! If the spin result is unsatisfactory following a reduced spin speed attempt to rectify the unbalanced load, then
on completion of the programme the load can be redistributed evenly in the drum by hand.Select a spin cycle.
Note: Do not attempt to spin heavy or absorbent single items as the machine cannot distribute these evenly.
If you need to wash a single item you will need to add some other items as ballast to allow the machine to distribute
the load evenly throughout the drum.
No water detection
The machine will automatically detect if it cannot take in water and will notify you by...
- flashing ‘H20‘ on the display.
If this occurs please check the appliance is plumbed in correctly (see Installation ‘Water connection ’).
Energy saving and water levels
Modern machines are designed to be as environmentally friendly as possible.
To achieve this water levels are kept to a minimum to ensure they are economic and use the lowest energy
possible. Unlike older appliances you will not see high water levels in the drum during washing.
! We recommend always washing as close to a full load as possible (see Programmes Table for the maximum
load size of your selected programme).
GB
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Detergents and Laundry
GB
Detergent dispenser
Washcare Tips
! Do not put any items into the drawer, other than
detergents designed to be released from the drawer, as they
may cause damage or blockage.
• DO NOT overload or underload the machine
(see the Programme Table for maximum load), in
addition to reducing the quality of the wash this may
also damage your laundry and the machine, whilst
causing the machine to become unstable and noisy.
Grate
• We strongly recommend that you DO NOT
wash underwired bras in this machine.
Should the wires become detached it could cause
damage to your laundry and the machine. If the
washcare label states that the bra is machine
washable, then we advise placing it in a sealed pillow
case or a similar washbag.
Drawer release
catch
Pre-wash
detergent
compartment.
Main wash detergent
Maximum:
compartment.
200 ml powder or
Maximum:
100 ml liquid
400 ml powder or
200 ml liquid
! Remember you will be charged for a service
engineers visit resulting from a detached bra
wire.
Fabric conditioner compartment
Maximum 120 ml
• Do not use the machine if the item to be washed
does not have a wash label.
Dispensing powder detergent
Before washing laundry we recommend you:
Toachievethebestwashresultsthemanufacturer's
recommended amount of detergent should be measured and
added to the main detergent compartment.
• Pre-treat awkward stains with washable
treatments.
Do not wash any items that have previously been
treated with solvents.
Dispensing tablets
Tablets can be dispensed via the machine drum or via the
dispenser drawer.
• Close zips, fasten belts, tie strings and close
press studs to prevent tangling.
! Please CHECK the detergent pack for dispensing
instructions.
! Incorrect use can damage your laundry.
• Empty all objects from pockets as they may
damage the laundry and the machine.
! Remember you will be charged for a service
engineers visit to rectify malfunction resulting
from objects such as coins, pens, hair grips
etc. falling from pockets.
Dispensing liquid detergent
We recommend the use of a detergent dosing ball, as
provided by your detergent manufacturer.
• Limit the size of absorbent loads ie.towels,to half
loads to give good washing and rinsing results.
Adding fabric conditioner
Pour the recommended amount of fabric conditioner into
the compartment. Do not exceed the maximum fill line.
• Place small items in a wash bag.
• Always follow the care label on items when
choosing the wash programme.
• Wash non-colourfast items or really dirty items
separately as they may affect other laundry.
Pre-wash
When selecting prewash, add detergent to both the pre-
wash and the main wash compartments.
Did you know that with Hotpoint and Ariel you ’ll get the best washing results?
Certain laundry products work better in some machines than others. At Hotpoint we know this is true because
we ’ve done the research to prove it. We used real everyday clothes and ran tests to find out which washing powder
works best with Hotpoint. The results proved that Hotpoint and Ariel produces the best washing results on all
your clothes.
Ariel can meet all your laundry needs.It is available as a biological powder for everyday wash loads. Colour powder
to keep your clothes staying brighter for longer and a Non-Bio powder for when you need brilliant cleaning but
are concerned about sensitive skin.
Did you know?...
• ... undisolved detergent left in the drawer or on clothes can be due to incorrect dosing or using the incorrect
dispensing method - CHECK the detergent manufacturers instructions on the pack for dispensing and dosage
advice.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Maintenance
Changing the plug
The wires in the power cord are coloured in accordance
with the following:
Cleaning
! Unplug your machine when cleaning it and before all
maintenance operations.
GB
! Do not clean any part of the machine with abrasive
cleaners, scouring agents, acids,any bleach or metal
polish as they may cause damage.
• Use a damp cloth or silicon polish to clean the
exterior surfaces of the appliance.
• Clean the internal surface of the door bowl regularly
with a soft cloth.A build up of soap powder and
water hardness residue may result in water leaking
from the door.
Green and Yellow
(Earth)wire to terminal
marked ‘E’, symbol
or coloured green
and yellow
13A ASTA
approved
fuse to BS1362.
Brown (Live) wire
to terminal
marked ‘L’
or coloured red.
Blue (Neutral) wire to
terminal marked ‘N’ or
coloured black.
• Always leave the appliance door ajar to prevent
unpleasant odours from forming.
Cross-bar
Cord clamp
Cleaning the dispenser drawer and compartments
It is advisable to clean the dispenser drawer regularly.
! If the plug being replaced is a non-rewirable type,
then the cut-off plug must be disposed of safely.
! Do not try to clean any part of the dispenser drawer
while the machine is running.
DO NOT leave it where it can be inserted into a
socket and create a shock hazard.
1. Pull out the drawer until
it reaches its stop.
! The power supply cord should be checked periodically
and replaced by a cord specially prepared for this
machine and fitted only by authorised technicians (see
Service ). Replacement power cords can be purchased,
at an extra cost from our Genuine Parts and
Accessories department or authorised dealers.
! The manufacturer denies any responsibility should any
of these rules not be followed.
2. Press the drawer release
buttontoremovethedispen-
ser drawer (see pic).
3. Clean and dry the
dispenser drawer, syphons,
grate and fabric conditioner
exit channel (A), ensuring any
build up ofdetergent and
fabric conditioner is fully
removed.
! Failure to do so may
lead to the machine
leaking from the
! If in doubt about any of the above consult a
qualified electrician.
Cleaning the pump
This appliance is fitted with a self-cleaning pump that
does not require any maintenance.
Sometimes, small items (such as coins or buttons)may
fall into the pre-chamber that protects the pump.
dispenser drawer.
Also regularly clean the
outlet pipe area (B)
! Make sure the wash cycle has ended and unplug
the appliance.
4. Relocate the dispenser
drawer and push it firmly
back into place.
To access the chamber:
A
1. Remove the kickstrip, on
the lower front of the
appliance, by holding at each
end and pulling towards you
(see figure ).
! We recommend a
maintenance wash 2 or 3
times a year, to avoid a
2. Unscrew the pump filter
by rotating it antclockwise,
until it can be removed (see
figure ). A little water may
leak from the pump: this is
perfectly normal.
build up of greasy deposits
and water hardness residue.
Run the 95 °White Cotton
programme, with the normal
3. Clean the interior
thoroughly, removing any
visible debris.
amount of detergent but no
laundry.
B
Moulded plug ! The plug must
not be used without the fuse cover in place.
4. Refit by screwing the
filter into place until it
reaches its ‘stop’ position.
If a replacement fuse holder/cover is
required, it must be of the same colour
coding or wording as shown on the base
of the plug. Replacements are available
from authorised dealers.
5. Refit the kickstrip, making
sure that the hooks are
securely in place before you
push in onto the appliance.
GB
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions and advice
General safety
• Unplug your appliance when cleaning it and during
all maintenance operations.
• This machine should only be used by adults and in
accordance with the instructions.
GB
• The pre-wash cycle is only necessary on extremely
soiled garments. Avoiding it will save on detergent,
time, water and between 5 and 15% energy.
• Treating stains with a stain remover or leaving
them to soak before washing will cut down the
need to wash them at high temperatures.
A pro gramme at 60 °C instead of 90 °C or one at
40 °C instead of 60 °C will save up to 50% on energy.
• Do not overload or underload the machine.In
addition to reducing the quality of the wash,
this may also damage your laundry and the machine.
• Do not pull on the power supply cable to unplug
the appliance from the electricity socket. Pull the
plug out.
• Use the correct quantity of detergent, depending
on the water hardness, how soiled the garments
are and the amount of laundry you have, to avoid
wastage and to protect the environment: despite
being biodegradable, detergents do contain
ingredients that alter the natural balance of the
environment. In addition, avoid using fabric
softener as much as possible.
• Do not open the machine door while the
appliance is in operation.
• Do not open the detergent dispenser while the
appliance is in operation.
• Never force the machine door:this could damage
the safety lock mechanism designed to prevent
any accidental opening.
• Turn off the water tap after every wash. This will
limit the wear of your appliances water system
and also prevent leaks.
• If you use your machine between late in the
afternoon and the early hours of the morning,you
will help reduce the electricity board ’s peak load.
• In the event of a malfunction, do not under any
circumstances touch internal parts in order to
attempt repairs.
• Always keep children well away from the appliance
while in operation. Do not let children play with the
machine or tamper with the controls.
• The appliance door tends to get quite hot during
the cycle.
• Should it have to be moved,proceed with the
help of two or three people and handle it with the
utmost care.Never try to do this alone, because
the appliance is very heavy.
• Before loading your laundry into the machine,
make sure the drum is empty.
• Check the water fill hose at least once a year.If
you see any cracks,replace it immediately:
during the wash cycles, high water pressure could
cause a cracked hose to split open.
Recycling and Disposal information
As part of Hotpoint ’s continued commitment to
helping the environment, Hotpoint reserve the right
to use quality recycled components to keep down
customer costs and minimise material wastage.
• Please dispose of packaging and old appliances
carefully.
• To minimise risk of injury to children, remove the
door and plug - then cut off mains cable, flush with
the appliance. Dispose of these parts separately
to ensure that the appliance can no longer be
plugged into a mains socket, and the door cannot
be locked shut.
! Never use hoses that have already been used.
• In the unlikely event of something not working -
see the Troubleshooting section.
Disposal of old electrical appliances
The European Directive 2002/96/EC on Waste Electrical
and Electronic Equipment (WEEE), requires that old
household electrical appliances must not be disposed
of in the normal unsorted municipal waste stream. Old
appliances must be collected separately in order to
optimise the recovery and recycling of the materials
they contain and reduce the impact on human health
and the environment.
Saving energy and respecting the
environment
Environmentally-friendly technology
If you only see a little water through your appliance
door, this is because thanks to the latest Hotpoint
technology, your machine only needs less than half the
amount of water to get the best results:
The crossed out “wheeled bin ”symbol on the
product reminds you of your obligation, that
when you dispose of the appliance it must
be separately collected.
an objective reached to respect the environment.
Saving on detergent,water,energy and time
Consumers should contact their local
authority or retailer for information concerning the
correct disposal of their old appliance.
• To avoid wasting resources,the machine should
be used with a full load. A full load instead of two
half loads allows you to save up to 50% on energy.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions and advice
recautionsand
Safety advice
Technical Details Chart
GB
! This machine was designed and built in compliance
with the applicable international safety regulations.
The following information is provided for your safety
and should be read carefully.
WT761, WT746, WT741, WT721
and WT 640
Models
59.5 cm wide
85 cm high
60 cm deep
Dimensions
Capacity
• This machine is designed for domestic use only.
from 1 to 7 kg
• Before using your machine make sure that the TWO
transit bolts,TWO rubber grommets and TWO
spacers have been removed (see page 5 ).
Electric
Voltage 220/240 50Hz
connections
Max absorbed power 1700W-2100W
• Any electrical work necessary to install this
machine should be carried out by a qualified
electrician.
Maximum pressure 1 MPa (10 bar)
Minimum pressure 0.05 MPa (0.5 bar)
drum capacity 54 or 58 litres
Water
connections
• Do not plug your machine into a socket when your
hands are wet.
up to 1600 rpm - WT761
up to 1400 rpm - WT746, WT741,
- WT640
• Do not try to modify this machine in any way.
• Do not let children play with the machine or with its
controls.
Spin speed
up to 1200 rpm - WT721
Control
• Do not lean on the door or use the door to lift or
move the machine.
60°C cotton (programme 4)
with Water Enhance
programme
according to
IEC 60456
• Do not wash garments that have previously been
treated with solvents.
- run with a load of 7 kg.
This appliance is compliant with
the following European
• Do not connect the machine to a single outlet
instantaneous water heater.
Community Directives:
• Do not connect the machine directly to a water-
softening unit; use the recommended amount of
detergent for the water hardness in your area.
- 73/23/EEC and 93/68/EEC (Low
Voltage) and subsequent
amendments - 89/336/EEC,
92/31/EEC and 93/68/EEC
(Electromagnetic Compatibility)
and subsequent amendments
• Do not overload or underload the machine.In
addition to reducing the quality of the wash,this
may also damage your laundry and the machine.
• Do not pull on the power supply cable to unplug
the appliance from the electricity socket. Pull the
plug out.
• Do not touch the drain water as it could reach very
high temperatures (over sink drainage).
• Never force the machine door; this could damage
the safety lock mechanism design to prevent any
accidental opening.
• In the event of a malfunction,do not under any
circumstances touch internal parts in order to
attempt repairs.
• Should it have to be moved,proceed with the help
of two or three people and handle it with the
utmost care. Never try to do this alone,because
the appliance is very heavy.
• Before loading your laundry into the machine,make
sure the drum is empty.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Something Wrong? Troubleshooting
If your machine seems not to be working GO through the following troubleshooting suggestion BEFORE you call your Service Centre
(see Service)
GB
Section 1: All Ultima Models - General Troubleshooting
Problem:
Possible causes / Solution
The machine won’t start:
(Nothing lights up on the
control panel).
• Check the appliance is fully plugged into the socket and switched on.
• Is the socket ok? Try another appliance in the socket to check.
• Is the fuse in the plug ok? If not, replace it, fuse must be 13 Amps (see Care and Maintenance ).
• There has been a power failure -Check another electrical device in your home to see if this is
the case.
• The ON/OFF button has not been pressed.
• The Start/Cancel button has not been pressed, for at least 3 seconds - Press and hold the
Start/Cancel button until the machine starts to operate.
• The appliance door is not shut properly -Close the door firmly and try the machine again.
• The Start/Cancel button has not been pressed, for at least 3 seconds -Press and hold the
Start/Cancel button until the machine starts to operate.
Lights/Display illuminate on
the control panel but the
washcycle will not start.
• The cold water supply tap is not turned on - (H2O is diplayed).
• Have you selected Time Delay (see Programmes and Option Modifiers)
• The Start/Cancel button has not been pressed,for at least 3 seconds - Press and hold the
Start/Cancel button until the machine starts to operate.
The machine fails to fill with
water.
• Is the ‘Prewash ’indicator light flashing? This indicates the machine has failed to take in
water (see Installation ) - Check that:
-The cold water inlet hose is connected to the tap.
-The hose is not kinked.
-The cold water supply tap is turned on...Ensure it is turned fully on.
-The water pressure is insufficient (see Technical Details Chart ).
-The inlet filter is not blocked...Turn off the water, unscrew the fill hose at the back of
the appliance then remove and clean the filter.
Note: Modern machines use less water and the water taken into the machine is
automatically adjusted depending on the load in the drum. For this reason, you may
not always be able to see water in the drum: But if the load is ‘wet ’and the machine
completes the wash cycle then the amount of water into the machine is sufficient.
• Has the drain hose been installed correctly (see Installation ).
• Are the drain hose,standpipe or undersink connections blocked?
The machine does not drain
or spin (during the first wash
cycle,after installation).
Note: If the drain hose is connected to an undersink ‘U ’trap - Check that the sink
trap blanking plug was removed before the drain hose was connected. This is the most
common installation fault.
• Is the drain hose kinked or squashed -Check the hose at the back of the machine.
• Carry out the additional checks listed below...
• There has been an unbalanced load in the drum and the machine could not spin - Try the
machine again with a different wash oad (see ‘Automatic Features ’,Programmes and Option
modifiers ).
• Has the ‘Rinse Hold ’option been selected?‘ Rinse Hold ’indicator ight will flash.
-To complete the paused programme press either the Start/Cancel button or the
Rinse Hold button (see Programmes and Option modifiers ).
The machine does not drain
or spin (although it has
drained/spun during
previous wash cycles).
The programme takes a long
time.
• If the machine completes the wash cycle, it is unlikely there is a problem.
• Check the programme table to be sure the programme you have selected is that most suited
for your needs -The table also gives an indication of approximate programme times you can
expect.
Note: The programme times listed in the Programme Table are approximate.
Options selected can affect the programme times (see Programmes and Option modifiers ).
The wash load, temperature and pressure of the incoming water supply can cause
some variation in the programme times.
There is too much foam in the
drum during the wash cycle.
• Check that the detergent you have used is suitable for ‘Automatic ’machines.
• Refer to the detergent manufacturers recommendations to ensure that you have not used
too much detergent.
• If you have used the wrong type of detergent (or too much), select a Rinse programme to
flush out your machine.
Steam is coming from the
dispenser drawer.
• This is not a fault,we have designed the machine to release steam from the drawers during
hot washes.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Something Wrong?
Troubleshooting
• The transit fixings were not removed correctly (see Installation ‘Remove the transit fixings ’)
- Failure to remove all the parts of the transit fixings will cause the machine to vibrate
excessively during spin.
Note: There are TWO transit fixings that need to be removed - two bolts, two washers,
two rubber grommets and two nylon spacers.
The machine makes a
noise or vibrates too
much during the spin
cycle.
GB
• The machine is not level (see Installation )-Adjust the feet so that the machine stands firm on the
floor (ie,it does not rock) and ensure the machine is level from front to back and from side to side.
• The machine is closed in, between furniture cabinets and the wall (see Installation ).
• Perhaps the machine was attempting to spin an unbalanced load -Try the machine again
with a different wash load.
• When you sort your laundry into wash groups, check all loose items, such as coins are
removed from the laundry. Check the drum at the end of each cycle and remove any loose
items (coins etc).
Note: ‘Super Silent ’refers to wash sound level only -there will always be some motor
and drum noise during spin.
...from behind or underneath:
• Check each end of the cold water inlet hose, ensuring connections at both ends are tight
and not leaking (see Installation ).
The machine leaks:
• Depending on the installation method used (see Installation ). Check that:
- the drain hose is firmly secured to the undersink ‘U ’trap, or...
- the drain hose is positioned correctly into the standpipe.
• Check that your water pressure is within limits (see Technical Details Chart ).
- If too high, try turning the cold water supply tap down slightly and try the machine
again (see Installation ).
...from the dispenser drawer (water leaking down the front of the machine):
• Check that the detergent dispenser is not blocked or obstructed.
- Remove the drawer from the machine and clean it (see Care and Maintenance ).
Not all the detergent
has been flushed out of
the dispenser drawer.
• Check the cold water supply tap is turned on sufficiently (see Installation ).
Is your water pressure is within limits (see Technical Details Chart ), if it is too low it may
not be sufficient to flush all the detergent out of the drawer.
• Check that the detergent dispenser is not blocked or obstructed.
-Remove the drawer from the machine and clean it (see Care and Maintenance ).
• Is your water pressure too low? (see T echnical Details Chart ).
Note:Are you using detergent tablets? - If yes, please check the detergent
manufacturers instructions on the side of the detergent box, not all detergent tablets
are suitable for use in the dispenser drawer some need to be placed into the machine
drum with the wash load for them to dissolve correctly.
The dispenser drawer
will not close properly or
is collecting water.
• Check that the detergent dispenser is not blocked or obstructed.
-Remove the drawer from the machine and clean it (see Care and Maintenance ).
Section 2: Specific Error Messages on the Control Panel and Digital Display
Your machine carries out automatic checks at various stages of the wash cycles - Error messages will be displayed on the
control panel to indicate there is something wrong.
The error message displayed is dependent upon which machine you have:
Error message:
‘H2O’ flashing in the display.
This indicates that the machine has failed to take in water (see Installation ).
Check that:
• the cold water inlet hose is connected to the cold water supply tap.
• the cold water inlet hose is not kinked.
• the cold water supply tap is turned on - Ensure it is turned fully on.
• the water pressure is sufficient (see Technical Details Chart ).
Display shows ‘door’.
This indicates that the door is not closed properly.
• Close the door firmly and try the machine again.
This indicates that the machine failed to drain, possibly because the pump filter is blocked.
• Your machine is fitted with a filter system for the pump - This filter may have become blocked.
( see Care and maintenance) for details of how to remove any blockage from the pump filter.
‘Wash Enhance’ and ‘Rinse
Hold’ and ‘Mini Load’ option
indicator lights flashing on
the control panel.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
11/2007 - 195 067 838 01
XEROX BUSINESS SERVICES
Spare Parts
Before calling the Service Centre:
GB
This is a complex machine. Repairing it yourself or
having a non-authorised person try to repair it could
cause harm to one or more persons,could damage
the machine and could invalidate the spare parts
warranty.
• Use the troubleshooting guide to see if you can
solve the problem yourself (see Troubleshooting).
• If not, turn off the machine and call the Service
Centre closest to you.
Call an authorised technician if you experience problems
while using the machine.
The spare parts have been designed exclusively for
this appliance and not for other uses.
! You will be charged for a service engineers visit if a
problem with your machine is caused by incorrect
installation or misuse.
Key Contacts
After Sales Service
Over 1100 trained specialists, directly employed by us, ensure that you can have
complete confidence in both the appliances and services we offer.
Repair Service and Information Help Desk
UK: 08709 066 066
Monday to Friday, 8am to 7.30pm
Saturday, 8.30am to 5.30pm
Sunday, 9.30am to 3.30pm
Republic of Ireland: 0818 313 413
Note: Our operators will require the following information:
Model number
Serial number
Date of purchase
Model number and Serial number can be found on the inside of the door.
Extended Warranties
UK:08709 088 088
Monday to Sunday, 8am to 8pm
Republic of Ireland: 0123 002 333
Genuine Parts and Accessories
UK: 08709 077 077
Monday to Friday, 8.30am to 5pm
Saturday, 8.30am to 12noon
Republic of Ireland: 0818 313 413
Indesit Company UK Limited, Morley Way, Peterborough, PE2 9JB
20
Download from Www.Somanuals.com. All Manuals Search And Download.
|