Hotpoint Washer HF8B 593 User Manual

Instructions for use  
WASHING MACHINE  
Contents  
GB  
Installation, 2-3-4-5  
Unpacking and levelling  
GB  
Connecting the electricity and water supplies  
The first wash cycle  
English,1  
Technical data  
Description of the washing machine  
and starting a wash cycle, 6-7  
Control panel  
Indicator lights  
Starting a wash cycle  
Wash cycles, 8  
Table of wash cycles  
Personalisation, 9  
Setting the temperature  
Functions  
HF8B 593  
Detergents and laundry, 10  
Detergent dispenser drawer  
Preparing the laundry  
Garments requiring special care  
Load balancing system  
Precautions and tips, 11  
General safety  
Disposal  
Care and maintenance, 12  
Cutting off the water or electricity supply  
Cleaning the washing machine  
Cleaning the detergent dispenser drawer  
Caring for the door and drum of your appliance  
Cleaning the pump  
Checking the water inlet hose  
Troubleshooting, 13-14  
Assistance, 15-16  
FUTURA  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the drain hose  
• the supply voltage is included within the values indica-  
ted on the Technical Data Plate fixed on the machine.  
GB  
Connect the drain hose,  
without bending it, to a  
draining duct or a wall drain  
situated between 65 and  
100 cm from the floor;  
• the socket is compatible with the washing machines  
plug. If this is not the case, replace the socket or the  
plug.  
65 - 100 cm  
Your appliance is now supplied with a 13 amp fused plug  
it can be plugged into a 13 amp socket for immediate use.  
Before using the appliance please read the instructions  
below.  
WARNING - THIS APPLIANCE MUST BE EARTHED.  
THE FOLLOWING OPERATIONS SHOULD BE CARRIED  
OUT BY A QUALIFIED ELECTRICIAN.  
The drain hose may be  
connected to an under-  
sink trap. Before connec-  
ting the drain hose from  
the machine ensure that  
any blanks or removable  
ends have been taken off  
the spigot.  
Replacing the fuse:  
When replacing a faulty fuse, a 13 amp ASTA approved  
fuse to BS 1362 should always be used, and the fuse  
cover re-fitted. If the fuse cover is lost, the plug must not  
be used until a replacement is obtained.  
Where it connects to  
the waste water pipe  
cut end off spigot or  
remove the blanking cap  
Replacement fuse covers:  
If a replacement fuse cover is fitted, it must be of the  
correct colour as indicated by the coloured marking or the  
colour that is embossed in words on the base of the plug.  
Replacements can be obtained directly from your nearest  
Service Depot.  
If it is placed over the edge  
of a basin or sink be sure  
the free end of the hose  
should not be underwater.  
Removing the plug:  
If your appliance has a non-rewireable moulded plug and  
you should wish to re-route the mains cable through parti-  
tions, units etc., please ensure that either:  
the plug is replaced by a fused 13 ampere rewireable plug  
bearing the BSI mark of approval.  
or:  
! We advise against the use of hose extensions; in case of  
absolute need, the extension must have the same diameter  
as the original hose and must not exceed 150 cm in length.  
Ensure that if the drain hose is pushed into a standpipe, that  
the end does not go down more than 15cms (6 inches). If  
the hose is pushed down too far, this may cause the machi-  
ne to self -syphon ie. continuously empty as it is filling.  
the mains cable is wired directly into a 13 amp cable out-  
let, controlled by a switch, (in compliance with BS 5733)  
which is accessible without moving the appliance.  
Disposing of the plug:  
Ensure that before disposing of the plug itself, you make  
the pins unusable so that it cannot be accidentally inserted  
into a socket.  
Electric connection  
Instructions for connecting cable to an alternative plug:  
Important: the wires in the mains lead are coloured in  
accordance with the following code:  
Before plugging the appliance into the mains socket, make  
sure that:  
Green & Yellow  
Blue  
Brown  
Earth  
Neutral  
Live  
the socket is earthed and in compliance with the appli-  
cable law;  
the socket is able to sustain the appliances maximum  
power load indicated on the Technical Data Plate fixed  
on the machine;  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
As the colours of the wires in the lead may not correspond  
with the coloured markings identifying the terminals in your  
plug, proceed as follows:  
Connect Green & Yellow wire to terminal marked E or  
or coloured Green or Green & Yellow.  
The first wash cycle  
GB  
Once the appliance has been installed, and before you use  
it for the first time, run a wash cycle with detergent and no  
laundry, setting the 2 programme.  
Connect Brown wire to terminal marked L or coloured Red.  
Connect Blue wire to terminal marked N or coloured Black.  
If a 13 amp plug (BS 1363) is used it must be fitted with a  
13 amp fuse, either in the plug or adaptor or at the distri-  
bution board.  
If you are in any doubt regarding the electrical supply to  
your machine, consult a qualified electrician before use.  
How to connect an alternative plug:  
The wires in this mains lead are coloured in accordance  
with the following code:  
BLUE  
BROWN  
NEUTRAL (N)  
LIVE (L)  
GREEN & YELLOW  
EARTH (E)  
GREEN &  
YELLOW  
13 ampere fuse  
BROWN  
BLUE  
CROSS-BAR  
CORD GRIP  
Disposing of the appliance:  
When disposing of the appliance please remove the plug  
by cutting the mains cable as close as possible to the plug  
body and dispose of it as described on the previous page.  
! The washing machine should not be installed in an ou-  
tdoor environment, not even where the area is sheltered,  
because it may be very dangerous to leave it exposed to  
damp, rain and thunderstorms.  
! When the washing machine is installed, the mains socket  
must be within easy reach.  
! Do not use extensions or multiple sockets.  
! The power supply cable must never be bent or dange-  
rously compressed.  
! The power supply cable must only be replaced by an  
authorised serviceman.  
Warning! The company denies all liability if and when these  
norms are not respected.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
GB  
Technical data  
Model  
HF8B 593  
width 59.5 cm  
height 85 cm  
depth 60 cm  
Dimensions  
Capacity  
from 1 to 8 kg  
Electrical  
please refer to the technical data plate  
fixed to the machine  
connections  
maximum pressure 1 MPa (10 bar)  
Water connections minimum pressure 0.05 MPa (0.5 bar)  
drum capacity 62 litres  
Spin speed  
up to 1500 rotations per minute  
Test wash cycles  
in accordance  
with directives  
1061/2010 and  
1015/201  
Programme  
Programme  
; Cotton Standard 60°.  
; Cotton Standard 40°.  
This appliance conforms to the following  
EC Directives:  
- 2004/108/EC (Electromagnetic Compa-  
tibility)  
- 2006/95/EC (Low Voltage)  
- 2002/96/EC  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Description of the washing  
machine and starting a wash cycle  
Control panel  
GB  
WASH CYCLE PROGRESS  
indicator lights  
DOOR  
ON/OFF button  
LOCKED  
TEMPERATURE  
indicator light  
knob  
START/PAUSE  
button with indicator  
light  
Detergent dispenser drawer  
FUNCTION  
buttons with  
indicator lights  
WASH CYCLE  
knob  
Detergent dispenser drawer: used to dispense  
detergents and washing additives (see “Detergents and  
START/PAUSE button with indicator light: starts or tem-  
porarily interrupts the wash cycles.  
laundry”).  
N.B. To pause the wash cycle in progress, press this  
button; the corresponding indicator light will flash orange,  
while the indicator light for the current wash cycle phase  
will remain lit in a fixed manner. If the DOOR LOCKED  
indicator light is switched off, the door may be opened  
(wait approximately 3 minutes).  
ON/OFF button: switches the washing machine on and off.  
WASH CYCLE knob: programmes the wash cycles. Du-  
ring the wash cycle, the knob does not move.  
To start the wash cycle from the point at which it was  
interrupted, press this button again.  
FUNCTION buttons with indicator light: used to select the  
available functions. The indicator light corresponding to the  
selected function will remain lit.  
Standby mode  
This washing machine, in compliance with new energy sa-  
ving regulations, is fitted with an automatic standby system  
which is enabled after about 30 minutes if no activity is  
detected. Press the ON-OFF button briefly and wait for the  
machine to start up again.  
TEMPERATURE knob: sets the temperature or the cold  
wash cycle (see “Personalisation”).  
WASH CYCLE PROGRESS indicator lights: used to  
monitor the progress of the wash cycle.  
The illuminated indicator light shows which phase is in  
progress.  
Consumption in off-mode: 0.5 W  
Consumption in Left-on: 0.5 W  
DOOR LOCKED indicator lights: indicates whether the  
door may be opened or not (see next page).  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Door locked indicator light  
Indicator lights  
GB  
If this indicator light is on, the appliance door is locked to  
prevent it from being opened accidentally; to avoid any  
damage, wait for the indicator light to switch off before you  
open the appliance door (wait approximately 3 minutes).  
The indicator lights provide important information.  
This is what they can tell you:  
Wash cycle phase indicator lights  
Once the desired wash cycle has been selected and has  
begun, the indicator lights switch on one by one to indicate  
which phase of the cycle is currently in progress.  
! If the START/PAUSE indicator light (orange) flashes rapidly  
at the same time as the function indicator light, this indicates  
a problem has occurred (see “Troubleshooting”).  
Wash  
Rinse  
Spin  
Pump out  
End of wash cycle  
Function buttons and corresponding indicator lights  
When a function is selected, the corresponding indicator  
light will illuminate.  
If the selected function is not compatible with the program-  
med wash cycle, the corresponding indicator light will flash  
and the function will not be activated.  
If a function which is incompatible with another function  
selected previously, only the most recent selection will  
remain active.  
Starting a wash cycle  
1. Switch the washing machine on by pressing the ON/OFF button. All the indicator lights will turn on for a few seconds,  
then only the indicator lights relative to the selected programme settings will remain lit and the START/PAUSE indicator light  
will flash.  
2. Load the laundry and close the door.  
3. Set the WASH CYCLE knob to the desired programme.  
4. Set the washing temperature (see “Personalisation”).  
5. Measure out the detergent and washing additives (see “Detergents and laundry”).  
6. Select the desired functions.  
7. Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit in a fixed  
manner, in green.  
To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle.  
8. At the end of the wash cycle the  
indicator light will switch on. The DOOR LOCKED indicator light will switch off, indi-  
cating that the door may be opened (wait approximately 3 minutes). Take out your laundry and leave the appliance door ajar  
to make sure the drum dries completely. Switch the washing machine off by pressing the ON/OFF button.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wash cycles  
Table of wash cycles  
GB  
Detergents  
Max.  
temp.  
(°C)  
Max.  
speed  
(rpm)  
Description of the wash cycle  
Essentials  
Anti Stain  
Whites  
1
2
40°  
60°  
1500  
1500  
5
5
-
-
-
-
-
-
180’  
180’  
60°  
(Max. 90°)  
Cotton Standard 60° (1): heavily soiled whites and resistant colours.  
Cotton Standard 40° (2): lightly soiled resistant and delicate colours.  
1500  
8
44  
1.09  
73 200’  
40°  
20°  
60°  
40°  
1500  
1500  
800  
8
8
4
4
44  
-
1.01  
-
84 185’  
5
6
6
Cotton Standard 20°: lightly soiled resistant and delicate colours.  
-
175’  
Synthetics: heavily soiled resistant colours.  
46  
46  
1.03  
0.56  
60 110’  
Synthetics (3): lightly soiled resistant colours.  
800  
60  
95’  
Specials  
Anti Allergy  
7
8
9
60°  
40°  
60°  
1500  
1000  
1500  
-
-
-
-
-
-
-
-
-
195’  
145’  
140’  
5
5
8
Baby  
Bed&Bath: washes bathroom laundry and bedlinen.  
Fastwash 60’: to refresh normal soiled garments quickly (not suitable  
for wool, silk and clothes which require washing by hand).  
10  
11  
60°  
30°  
1500  
800  
44  
71  
0.84  
0.20  
44  
38  
60’  
30’  
3.5  
3.5  
Fastwash 30’: to refresh lightly soiled garments quickly (not suitable  
for wool, silk and clothes which require washing by hand).  
Extras  
12 Shirts  
40°  
600  
-
-
-
2
70’  
13 Wool: for wool, cashmere, etc.  
14 Delicates  
40°  
30°  
800  
0
-
-
-
-
-
-
90’  
80’  
2
1
Partials cycles  
A
B
Rinse  
-
-
1500  
1500  
-
-
-
-
-
-
-
-
36’  
16’  
8
8
Spin+Pump out  
-
The length of cycle shown on this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary according to factors  
such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.  
1) Test wash cycle in compliance with directive 1061/2010: set wash cycle  
with a temperature of 60°C.  
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for  
garments which can be washed at 60°C. The actual washing temperature may differ from the indicated value.  
2) Test wash cycle in compliance with directive 1061/2010: set wash cycle  
with a temperature of 40°C.  
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for  
garments which can be washed at 40°C. The actual washing temperature may differ from the indicated value.  
For all Test Institutes:  
2) Long wash cycle for cottons: set wash cycle  
with a temperature of 40°C.  
3) Long wash cycle for synthetics: set wash cycle 6 with a temperature of 40°C.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Personalisation  
Setting the temperature  
GB  
Turn the TEMPERATURE knob to set the wash temperature (see Table of wash cycles).  
The temperature may be lowered, or even set to a cold wash ( ).  
The washing machine will automatically prevent you from selecting a temperature which is higher than the maximum value  
set for each wash cycle.  
! Exception: if the  
programme is selected, the temperature can be increased up to a value of 90°C.  
Functions  
The various wash functions available with this washing machine will help to achieve the desired results, every time.  
To activate the functions:  
1. Press the button corresponding to the desired function;  
2. the function is enabled when the corresponding indicator light is illuminated.  
Note: If the indicator light flashes rapidly, this signals that this particular function may not be selected in conjunction with the  
selected wash cycle.  
Spin Exclusion  
The washing machine will not carry out the spin cycle, but rather a drum spin at medium speed to assist water draining.  
Recommended when washing garments which are difficult to iron.  
! This function may not be used in conjunction with wash cycles 7, 14.  
Reduced Creases  
By selecting this function, the wash and spin cycles will be modified in order to reduce the formation of creases. At the end  
of the cycle the washing machine will perform slow rotations of the drum; the REDUCED CREASES and START/PAUSE indi-  
cator lights will flash (orange) and the  
phase will remain lit in a fixed manner. To end the cycle, press the START/PAUSE  
button or the REDUCED CREASES button.  
! This function may not be used in conjunction with wash cycles 1, 2, 7, 11, 13, A, B.  
Extra rinse  
By selecting this function, the efficiency of the rinse is increased and optimal detergent removal is guaranteed. It is particularly  
useful for sensitive skin.  
! This function may not be used in conjunction with wash cycles 7, 11, 14, B.  
Super Wash  
Because a greater quantity of water is used in the initial phase of the cycle, and because of the increased cycle duration, this  
function offers a high-performance wash.  
! This function may not be used in conjunction with wash cycles 2, 7, 10, 11, 13, 14, B.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Detergents and laundry  
Cotton Standard 20°: use this cycle 5 for heavily soiled  
Detergent dispenser drawer  
GB  
cotton loads. The effective performance levels achieved at  
cold temperatures, which are comparable to washing at  
40°, are guaranteed by a mechanical action which opera-  
tes at varying speed, with repeated and frequent peaks.  
Anti Allergy: use programme 7 to remove major allergens  
such as pollen, mites, cat’s and dog’s hair.  
Baby: use the special wash cycle 8 to remove the soiling  
typically caused by babies, while removing all traces of  
detergent from nappies in order to prevent the delicate  
skin of babies from suffering allergic reactions. The cycle  
has been designed to reduce the amount of bacteria by  
using a greater quantity of water and optimising the effect  
of special disinfecting additives added to the detergent.  
Bed&Bath: use programme 9 to wash bed linen and to-  
wels in one single cycle: it optimises softener performance  
and helps you save time and energy. We recommend the  
use of powder detergent.  
Successful washing results also depend on the correct  
dose of detergent: adding too much detergent will not  
necessarily result in a more efficient wash, and may in fact  
cause build up on the inside of your appliance and contri-  
bute to environmental pollution.  
! Use powder detergent for white cotton garments, for pre-  
washing, and for washing at temperatures over 60°C.  
! Follow the instructions given on the detergent packaging.  
! Do not use hand washing detergents; they create too  
much foam.  
Open the detergent di-  
spenser drawer and pour  
in the detergent or washing  
additive, as follows.  
*
1
2
Shirts: use the special 12 wash cycle to wash shirts in  
different fabrics and colours to guarantee they receive the  
best possible care.  
Wool: all wool garments can be washed using programme  
13, even those carrying the “hand-wash only”  
label.  
For best results, use special detergents and do not exceed  
2 kg of laundry.  
! Do not pour detergent into the middle compartment (*).  
Detergent should only be poured into the compartment 1.  
Delicates: use programme 14 to wash very delicate  
garments with decorative features, such as diamantes and  
sequins.  
We recommend turning the garments inside out before  
washing and placing small items into the special bag for  
washing delicates.  
Use liquid detergent on delicate garments for best results.  
To wash silk garments and curtains select cycle 14  
and then function “Reduced Creases” (in this case it will  
also be possible to enable the “Extra Rinse” option); the  
machine will end the cycle while the laundry is soaking,  
the “Reduced Creases” and START/PAUSE indicator  
lights will flash (orange) and the RINSE phase will remain  
lit in a fixed manner. To drain the water so that the laundry  
may be removed, press the START/PAUSE button or the  
“Reduced Creases” button.  
compartment 1: Detergent for the wash cycle  
(powder or liquid)  
For best results liquid detergent should be poured in the  
dispenser immediately before the start of the programme.  
compartment 2: Additives (fabric softeners, etc.)  
The fabric softener should not overflow the grid.  
Preparing the laundry  
• Divide the laundry according to:  
- the type of fabric/the symbol on the label  
- the colours: separate coloured garments from whites.  
• Empty all garment pockets and check the buttons.  
• Do not exceed the values listed in the “Table of wash  
cycles”, which refer to the weight of the laundry when dry.  
How much does your laundry weigh?  
1 sheet 400-500 g  
Load balancing system  
Before every spin cycle, to avoid excessive vibrations  
before every spin and to distribute the load in a uniform  
manner, the drum rotates continuously at a speed which  
is slightly greater than the washing rotation speed. If,  
after several attempts, the load is not balanced correctly,  
the machine spins at a reduced spin speed. If the load is  
excessively unbalanced, the washing machine performs  
the distribution process instead of spinning. To encourage  
improved load distribution and balance, we recommend  
small and large garments are mixed in the load.  
1 pillow case 150-200 g  
1 tablecloth 400-500 g  
1 bathrobe 900-1,200 g  
1 towel 150-250 g  
Garments requiring special care  
Anti Stain: the programme 1 is suitable to heavily-soiled  
garments with resistant colours. It ensures a washing  
class that is higher than the standard class (A class). When  
running the programme, do not mix garments of different  
colours. We recommend the use of powder detergent.  
Pre-treatment with special additives is recommended if  
there are obstinate stains.  
Whites: use this cycle 2 to wash white clothes. The pro-  
gramme is designed to maintain the brightness of white  
clothes over time. Use powder detergent for best results.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Precautions and tips  
! This washing machine was designed and constructed in  
accordance with international safety regulations. The fol-  
lowing information is provided for safety reasons and must  
therefore be read carefully.  
GB  
General safety  
• This appliance was designed for domestic use only.  
• This appliance is not intended for use by persons (inclu-  
ding children) with reduced physical, sensory or mental  
capabilities, or lack of experience and knowledge, unless  
they have been given supervision or instruction concer-  
ning use of the appliance by a person responsible for their  
safety. Children should be supervised to ensure that they  
do not play with the appliance.  
• Do not touch the machine when barefoot or with wet or  
damp hands or feet.  
• Do not pull on the power supply cable when unplugging  
the appliance from the electricity socket. Hold the plug  
and pull.  
• Do not open the detergent dispenser drawer while the  
machine is in operation.  
• Do not touch the drained water as it may reach extreme-  
ly high temperatures.  
• Never force the porthole door. This could damage the safety  
lock mechanism designed to prevent accidental opening.  
• If the appliance breaks down, do not under any circum-  
stances access the internal mechanisms in an attempt  
to repair it yourself.  
• Always keep children well away from the appliance while  
it is operating.  
• The door can become quite hot during the wash cycle.  
• If the appliance has to be moved, work in a group of two  
or three people and handle it with the utmost care. Never  
try to do this alone, because the appliance is very heavy.  
• Before loading laundry into the washing machine, make  
sure the drum is empty.  
Disposal  
Disposing of the packaging materials: observe local regu-  
lations so that the packaging may be re-used.  
The European Directive 2002/96/EC on Waste Electrical  
and Electronic Equipment, requires that old household  
electrical appliances must not be disposed of in the normal  
unsorted municipal waste stream. Old appliances must be  
collected separately in order to optimise the recovery and  
recycling of the materials they contain and reduce the im-  
pact on human health and the environment. The crossed  
out “wheeled bin” symbol on the product reminds you of  
your obligation, that when you dispose of the appliance it  
must be separately collected. Consumers should contact  
their local authority or retailer for information concerning the  
correct disposal of their old appliance.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Care and maintenance  
2. unscrew the lid by rota-  
ting it anti-clockwise (see  
figure): a little water may  
trickle out. This is perfectly  
normal;  
Cutting off the water and electricity  
supplies  
GB  
• Turn off the water tap after every wash cycle. This will limit  
wear on the hydraulic system inside the washing machine  
and help to prevent leaks.  
• Unplug the washing machine when cleaning it and du-  
ring all maintenance work.  
Cleaning the washing machine  
3. clean the inside thoroughly;  
4. screw the lid back on;  
5. reposition the panel, making sure the hooks are securely  
in place before you push it onto the appliance.  
The outer parts and rubber components of the appliance  
can be cleaned using a soft cloth soaked in lukewarm  
soapy water. Do not use solvents or abrasives.  
Cleaning the detergent dispenser drawer  
Checking the water inlet hose  
Remove the dispenser by  
raising it and pulling it out  
(see figure).  
Wash it under running wa-  
ter; this operation should be  
repeated frequently.  
1
Check the inlet hose at least once a year. If there are any  
cracks, it should be replaced immediately: during the wash  
cycles, water pressure is very strong and a cracked hose  
could easily split open.  
! Never use second-hand hoses.  
2
Caring for the door and drum of your  
appliance  
• Always leave the porthole door ajar in order to prevent  
unpleasant odours from forming.  
Cleaning the pump  
The washing machine is fitted with a self-cleaning pump  
which does not require any maintenance. Sometimes, small  
items (such as coins or buttons) may fall into the pre-chamber  
which protects the pump, situated in its bottom part.  
! Make sure the wash cycle has finished and unplug the  
appliance.  
To access the pre-chamber:  
1. using a screwdriver,  
remove the cover panel  
on the lower front part of  
the washing machine (see  
figure);  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure  
that the problem cannot be solved easily using the following list.  
GB  
Problem:  
Possible causes / Solutions:  
The machine does not switch on.  
• The appliance is not plugged into the socket fully, or not enough to make contact.  
• There is no power to the socket, or the fuse has blown in the mains plug.  
The wash cycle does not start.  
• The door is not closed properly.  
• The ON/OFF button has not been pressed.  
• The START/PAUSE button has not been pressed.  
• The water tap has not been turned on to allow water to flow into the machine.  
The machine does not fill with wa-  
• The water inlet hose is kinked.  
ter or the indicator light for the first • The water inlet hose is not connected to the water supply.  
wash cycle stage flashes rapidly.  
• The water pressure is too low.  
• The water tap has not been turned on to allow water to flow into the machine.  
• There is no water supply to the house.  
• The inlet valve filter is blocked.  
• The START/PAUSE button has not been pressed.  
The machine continuously fills with • The top of the drain hose is too low - It must be fitted at a height between 65  
water and continually drains away  
or Water left in the drum  
or Stuck on wash.  
and 100 cm from the floor (see “Installation”).  
• The drain hose is connected incorrectly to the sink trap allowing water to run  
into the machine, the drain hose must be positioned higher than the bottom of  
the sink to prevent water flowing down the drain hose.  
• The end of the drain hose has been pushed too far down the standpipe, the  
‘U’ bracket should be fitted 100 mm from the end of the drain hose.  
The machine does not drain or  
spin.  
• The Pump filter is blocked.  
• The drain hose is kinked (see “Installation”).  
• New Installation - The blanking cap or spigot has not been removed if con-  
nected under a sink.  
• The drain hose or sink trap is blocked.  
• The wash cycle does not include draining, some wash cycles require the drain  
phase to be started manually.  
• The REDUCED CREASES function button has been activated. To complete  
the wash cycle, press the START/PAUSE button.  
The machine does not heat or poor • The ‘Temperature’ selector knob is in the “ ” position.  
wash results.  
The programme takes too long.  
• Programme times will vary due to water pressure, the incoming water tempe-  
rature and if the wash load goes out of balance. This will increase the pro-  
gramme times accordingly (see ‘ The machine wont spin properly’ below).  
The machine vibrates a lot during  
the spin cycle.  
• The feet have not been adjusted, enabling the machine to rock.  
• New Installation - Either the Transit Bolts including the plastic spacers, or the  
Polystyrene Packaging have not been removed when installing the machine.  
• The machine is trapped between cabinets and/or walls.  
• The load is in a slight out of balance condition and machine is spinning, but at  
a lower speed.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The machine is noisy.  
• There will always be some motor, pump and drum noise during spin.  
GB  
The machine wont spin properly.  
• Out of Balance detected when attempting to go into a spin cycle - If this  
happens the machine will continue to try to repeat the distribution of the load  
required before the machine will go into higher spin speeds - This will increase  
the programme time accordingly. This is a safety feature to prevent damage.  
Out of Balance can be caused by washing a single heavy item (eg duvet, quilt,  
etc). - Try the programme again using a different load.  
The machine leaks from the  
dispenser.  
• The dispenser drawer is blocked with detergent and requires cleaning.  
• The water pressure is too high and requires turning down - turn down the tap  
on the water supply pipe slightly and try again.  
• The machine is tilting forwards - It must be level when in its final position.  
The machine leaks (other than di-  
spenser).  
• The fill hose is loose, check both the cabinet and tap ends.  
• The fill hose is tight but still leaks, if so replace the rubber washers, or the fill  
hose is missing the rubber washer.  
• The drain hose is not fixed in properly.  
The indicator lights on the console  
are flashing rapidly.  
• Switch off the machine and unplug it, wait for approximately 1 minute and then  
switch it back on again If the problem persists contact the Technical Assistance  
Service.  
The machine smells.  
• The machine requires a service wash. Run a n° 2 wash cycle with detergent  
and no laundry.  
The machine door cannot be  
opened.  
• The door will not open until the door lock indicator light goes out shortly after  
the program has finished.  
Door Seal damaged at the bottom.  
• The door seal has drainage holes at the bottom - This is normal.  
• The water level is correct if it can be seen at the bottom of the door.  
The water level is too low when  
the machine is washing.  
There is too much foam.  
• The detergent is not suitable for machine washing (it should display the text  
‘for washing machines’ or ‘hand and machine wash’ or the like).  
Too much detergent was used - less detergent is required in soft water.  
After completing the programme,  
or before starting a programme,  
the machine has turned itself off  
(no lights).  
To comply with new energy saving regulations the machine is fitted with an  
automatic standby system. Press ‘ON/OFF’ button for 3 seconds to activate  
the machine, it can then either be switched off or a new programme selected.  
General.  
Your washing machine contains sensors that monitor progress during the wash  
cycle (eg: Water Levels, Temperatures, Out of Balance loads, Wash time/pro-  
gress).  
Normally, if your machine successfully completes the cycle, there is unlikely to  
be anything wrong!  
Remember, you will be charged for a service call for problems caused by incorrect installation, as listed above.  
Not emptying contents from pockets may cause pump or drain blockages, or may damage the machine.  
Do not wash items which do not have a wash label, or wash items that are not intended as machine washable.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assistance  
Guarantee  
12 Months Parts and Labour Guarantee  
GB  
Your appliance has the benefit of our manufacturers guarantee, which covers the cost of breakdown repairs  
for twelve months from the date of purchase.  
This gives you the reassurance that if, within that time, your appliance is proven to be defective because of  
either workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost  
to you.  
This guarantee is subject to the following conditions:  
-
The appliance has been installed and operated correctly and in accordance with our  
operating and maintenance instructions.  
-
-
-
The appliance is used only on the electricity or gas supply printed on the rating plate.  
The appliance has been used for normal domestic purposes only.  
The appliance has not been altered, serviced, maintained, dismantled, or otherwise  
interfered with by any person not authorised by us.  
-
-
-
Any repair work must be undertaken by us or our appointed agent.  
Any parts removed during repair work or any appliance that is replaced become our property.  
The appliance is used in the United Kingdom or Republic of Ireland.  
The guarantee does not cover:  
-
-
-
Damage resulting from transportation, improper use, neglect or interference or as a result  
of improper installation.  
Replacement of any consumable item or accessory . These include but are not limited to: plugs,  
cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.  
Replacement of any removable parts made of glass or plastic.  
THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL  
OR NON-DOMESTIC PREMISES.  
5 Year Parts Guarantee  
Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you  
registering your appliance with us and the parts being fitted by one of our authorised engineers. There will  
be a charge for our engineers time. To activate the extra parts warranty on your appliance, simply call our  
registration line on 08448 24 24 24 (ROI 01 230 0800).  
Extended Guarantees  
We offer a selection of repair protection plans that enable you to fully cover yourself against the expense of repair  
bills for the life of your policy. To find the ideal plan for you please call our advice line on  
08448 226 226 (Republic of Ireland 01 230 0233).  
Free Helpdesk Service  
We have a dedicated team who can provide free advice and assistance with your appliance if you  
experience any technical difficulties within the first 90 days of ownership. Simply call our Hotpoint Service  
Hotline on 08448 224 224 (Republic of Ireland 0818 313 413) for telephone assistance, or, where  
necessary, to arrange for an engineer to call. If we cannot resolve the technical problem we will replace your  
machine or, if you prefer, give you your money back.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
195108618.01  
01/2013  
-
Xerox Fabriano  
After Sales Service  
No one is better placed to care for your Hotpoint appliance during the course of its working  
life than us - the manufacturer.  
GB  
Essential Contact Information  
Hotpoint Service  
We are the largest service team in Europe offering you access to 400 skilled telephone advisors and 1000  
fully qualified engineers on call to ensure you receive fast, reliable, local service.  
UK: 08448 224 224  
Republic of Ireland: 0818 313 413  
Please note: Our advisors will require the following information:  
Model number:  
Serial number:  
Parts and Accessories  
We supply a full range of genuine replacement parts as well as accessory products that protect and  
hygienically clean your appliance to keep it looking good and functioning efficiently throughout its life.  
UK: 08448 225 225  
Republic of Ireland: 0818 313 413  
Appliance Registration  
We want to give you additional benefits of Hotpoint ownership. To activate your free 5 year parts guarantee  
you must register your appliance with us.  
UK: 08448 24 24 24  
Republic of Ireland: 01 230 0800  
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB  
Indesit Company Unit 49 Airways Industrial Estate,Dublin 17  
Recycling & Disposal Information  
As part of Hotpoints continued commitment to helping the environment, Hotpoint reserves the right to use  
quality, recycled components to keep down customer costs and minimise material wastage.  
Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children, remove  
the door, plug and cut the mains cable off flush with the appliance. Dispose of these parts separately to  
ensure that the appliance can no longer be plugged into a mains socket, and the door  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Graco Baby Accessories PD178040A User Manual
Haier Clothes Dryer GDZ22 2 User Manual
Haier Flat Panel Television 15HL25S User Manual
Haier Freezer HUM013EA User Manual
Hamilton Beach Coffeemaker 47453 User Manual
HANNspree Flat Panel Television K215 10A1 User Manual
Hotpoint Cooktop EH12 User Manual
HP Hewlett Packard Weather Radio HP16540a User Manual
Hyundai Car Video System H CMD4007 User Manual
IBM Network Card EM78P259N 260N User Manual