Haier Clothes Dryer GDZ22 2 User Manual

Time Remaining(Min)  
Time On(Hour)  
More Time  
Dry  
Cool down  
More Dry  
Power  
On/Off  
GDZ22-2  
On  
O
High  
Delay  
Start  
Cycle completed  
Extend trumble  
Less Time  
Louder  
Softer  
Off  
Start  
Medium  
Low  
Customer  
Normal  
ff  
Auto Dry  
Pause  
Bulky Items  
Less Dry  
Timed Dry  
Rack DRY  
Air Only(No Heat)  
Wrinkle  
Care  
Dryness  
Level  
Cycle  
Heavy Duty  
Casual  
Timed  
Cycles  
Signal  
Temp  
Cycles  
Towels/Cotton  
Delicate  
Electric  
Dryer  
User Manual-  
Model #  
GDZ22-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
16. This dryer must be properly installed in accordance with the  
installation instructions before it is used. See grounding instructions  
in the installation section.  
17. Proper grounding must be ensured to reduce the risk of electric shock  
and fire. Check with a qualified electrician or service personnel if you  
are in doubt as to whether the dryer is properly grounded.  
18. Use the dryer only for its intended purpose, drying clothes.  
19. Always disconnect dryer from electrical supply before attempting any  
service. Disconnet power cord by grasping the plug,not the cord.  
20. Replace worn power cords and/or loose plugs.  
21. To reduce the risk of electric shock or fire, do not use extension cords or  
adapters to connect dryer to electrical power source.  
22. Exhaust air must not be discharged into a flue which is used for exhaust  
ing fumes from appliances burning gas or other fuels.  
23. There has to be adequate ventilation to avoid the back flow of gases into  
the room from appliances burning other fuels including open fires, when  
operating the tumble dryer.  
24. The appliance must not be installed behind a lockable door, a sliding door  
or a door with a hinge on the opposite side to that of the tumble dryer.  
25.  
:Warning: Hot surface  
As dry cleaning solvents, gasoline, vegetable and cooking oils are highly  
hazardous materials, items soaked in or spotted with such should not be used in  
the dryer, Items may still contain a substantial amount of the hazardous material  
after being washed.When such items are exposed to heat they could ingnite. As  
clothes are stacked and piled up in the dryer the heat cannot escape. Due to this,  
items become hot enought to possibly ignite. Washing in hot water with extra  
detergent would reduce but not eliminate the risk of fire.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
Tables Of Contents  
PAGE  
Safety Instructions ............................................................................ 1  
OPERATING INSTRUCTIONS ............................................................ 4  
Understanding the Control Panel.......................................................... 4  
Preparations before drying  
.................................................................. 6  
Load clothes into dryer  
......................................................................  
7
7
Auto Dry cycle...................................................................................  
Timed Dry cycle  
................................................................................. 10  
................................................................................. 10  
Rack Dry cycle  
Other Features................................................................................. 11  
Normal Operating Sounds................................................................. 12  
Tips................................................................................................. 12  
Care and Cleaning Guide............................................................... 13  
Troubleshooting.............................................................................. 14  
INSTALLATION INSTRUCTIONS  
....................................................... 15  
Tools and Materials Required.............................................................. 15  
Electrical Requirements...................................................................... 15  
Unpacking Your Dryer........................................................................ 15  
Exhaust System Connections.......................................................... 16  
Requirements and Instructions............................................................ 16  
Materials ............................................................................................17  
Location of Your Dryer........................................................................ 19  
Installation in Mobile Home ............................................................... 20  
Electrical Connections.................................................................... 21  
Requirements and Instruction.s............................................................ 21  
3-Wire Cord Connections................................................................... 22  
Specifica.t.io...n................................................................................... 23  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATING INSTRUCTIONS  
Understanding the Control Panel  
Time Remaining(Min)  
More Time  
Power  
On/Off  
Dry  
Time On(Hour)  
More Dry  
Less Dry  
Cool down  
Cycle completed  
Extend tumble  
On  
Off  
Delay  
Start  
High  
Less Time  
Louder  
Softer  
Off  
Start  
GDZ22-2  
Customer  
Normal  
Medium  
Low  
Auto Dry  
Timed Dry  
Rack Dry  
Pause  
Bulky Items  
Wrinkle  
Care  
Air Only(No Heat)  
Cycle  
Signal  
Dryness  
Heavy Duty  
Cotton  
Casual  
Timed  
Level  
Cycles  
Temp  
Cycles  
Delicate  
12  
Time Remaining(Min)  
More Time  
Power  
On/Off  
Dry  
Time On(Hour)  
More Dry  
Less Dry  
Cool down  
Cycle completed  
Extend tumble  
On  
Delay  
Start  
High  
Less Time  
Louder  
Softer  
Off  
Start  
Off  
Customer  
Normal  
Medium  
Auto Dry  
Timed Dry  
Rack dry  
Pause  
Bulky Items  
Low  
Wrinkle  
Care  
Air Only(No Heat)  
Cycle  
Signal  
Dryness  
Level  
Heavy Duty  
Cotton  
Casual  
Timed  
Cycles  
Cycles  
Temp  
Delicate  
11  
10  
9
8
7
6
5
4
3
2
1
Power On/Off Button: (1)  
Press the button once to operate the dryer. Press the button once again to turn  
the dryer "OFF".  
Start/Pause Button: (2)  
Press this button once to start the dry process. Press this button once again to  
pause the activity during the dry cycle.  
Wrinkle Care Button: (3)  
Used to select wrinkle-proof function. Automatically set as off after powering on.  
This function is used together with delay start function.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cycle Signal Button: (4)  
Used to select buzzing volume or turn off the buzzer.  
Timed/Cycles Button: (5)  
"Timed/Cycles" button will let you select your desired dry mode.  
Auto Dry: automatically set "Dryness Level", "Temp", "Cycle Signal",  
"Wrinkle Care" buttons status according to clothes loaded.  
Timed Dry: you can set status of "Temp", "Cycle Signal" and "Wrinkle Care"  
buttons and dry time with "More Time" and "Less Time" buttons by yourself.  
Rack Dry: the program used to dry article like sport shoes.  
More Time & Less Time Button: (6)  
Set time from 0 to 180 minute when Timed Dry or Rack Dry cycle selected.  
Cycles Button: (7)  
"Cycle" button will let you select your desired dry cycles. For your convenience,  
there are seven fabric care dry cycles programmed in this mode:Customer,  
Normal, Heavy Duty, Cotton, Delicate, Casual and Bulky Items.  
Customer  
Normal  
The drying program defined by user himself and stored.  
Normal drying  
Heavy Duty  
Cotton  
Big clothes drying like jeans  
Special drying for cotton clothes  
Drying small quantity clothes  
Delicate  
Casual  
Drying underwear or clothes requiring smoothness  
Drying bulky clothing  
Bulky Items  
Delay Start Button: (8)  
This convenient feature lets you delay the start of the dry cycle between 3 to  
24 hours. Press the "Delay Start" to choose the number of hours you want to  
delay the start of the cycle.  
If no delay, the delay start indicator is off and remaining time indicator is on.  
The nixie display indicates remaining time of non-reserved program.  
If setting "Delay Start" in standby status, the nixie display indicates 3 hr, which  
will increase by 1 hr with each pressing (until 24 and return to 3). If keep  
pressed for 1.5 s, nixie display indicated value will increase continuously.  
Temp Button: (9)  
Used to set drying temperature. There are 4 available drying temperatures:  
High, Medium, Low, and Air only(no heat).  
Dryness Level Button: (10)  
Used to set drying time of auto-programs. If no auto-program is selected,  
pressing the button is inactive and will get alarms.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Status lights: (11)  
Status lights give notification of which part of the cycle the machine is in.  
Nixie display: (12)  
Indicate remaining time (min) during cycle operation.  
Indicate remaining reserved time (hr) during reservation.  
Note: if door opened during cycle running, displays "E2" and alarms.  
Understanding the Function Light Indicator:  
The function "display light" indicates selected feature is "ON" or the  
cycle is about to begin.  
During the dry cycle, "flashing light" indicates current running program.  
Rapidly flashing light indicates that the dryer is not operating properly.  
Preparations before drying  
Group the clothes of the same kind (cotton, chemical fibres, woolen) to dry.  
Dark and light colored clothes shall be separately dried. Fabrics prone to falling  
lint and those prone to adhering lint shall be separately dried. Clothes prone to  
falling lint shall be turned inside out before putting into the dryer.  
Make sure buttons and ornaments on the clothes are high temperature resistant  
and won't damage drum surface. Before loading, the clothes shall have their  
zippers zipped up, buttons and hooks done up and belts tied so as to avoid  
entanglement or other obstacles.  
If possible, turn out the clothes pockets for uniform drying.  
Check if clothes remain soiled. If yes, wash it away again, otherwise the soils after  
drying may not be removed permanently.  
Small articles shall be collected in a mesh bag before loading and drying, so as  
to avoid entanglement and ensure easy to be taken out.  
Make sure power socket is reliably grounded. The grounding terminal shall not be  
connected to gas or tap water pipelines.  
Make sure exhaust duct has been connected with extension pipe.  
Make sure lint filter is clean and then assemble it properly. If lint filter is not  
in place, tumbling items could enter the exhaust system and cause damage  
to the dryer.  
Notes: It applies to Auto Dry cycle and Timed Dry cycle. For Rack Dry cycle,  
remove the lint filter and assemble the drying rack with its rear end slightly  
downward inclined. The assembled status is as shown in the following figure:  
Drying rack  
Drum  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Load clothes into dryer  
Auto Dry cycle and Timed Dry cycle  
The appropriate load shall be 1/3 ~ 1/2 of the drum volume. Avoid too much load,  
for a certain space is needed to allow clothes free rotation for uniform and wrinkle-  
proof drying.  
When drying big articles, only 2-3 pieces shall be loaded at a time and  
supplemented with middle and small articles.  
For elaborate clothes or less load, two towels without lint falling may be added to  
get better drying and wrinkle-proof effects.  
Do not excessively dry clothes to avoid wrinkles, shrinkage, roughness, electrostatic  
charges accumulation and more lint.  
Rack Dry cycle  
This program is designed specially for articles like sport shoes. During drying  
please make sure the clothes reliably stay on the rack with no risk of entangling  
the agitation blade while drum is rotating.  
Note: If drying rack is not in place, rolling inner tub could collid with  
drying rack and causes damage to the dryer and drying rack.  
Auto Dry cycle  
Time Remaining(Min)  
More Time  
Power  
Dry  
Time On(Hour)  
More Dry  
On/Off  
Cool down  
Cycle completed  
Extend tumble  
On  
Off  
Delay  
Start  
High  
Less Time  
Louder  
Softer  
Off  
Start  
Customer  
Normal  
Medium  
Low  
Auto Dry  
Timed Dry  
Rack dry  
Pause  
Bulky Items  
Less Dry  
Wrinkle  
Care  
Air Only(No Heat)  
Cycle  
Signal  
Dryness  
Level  
Heavy Duty  
Cotton  
Casual  
Timed  
Cycles  
Cycles  
Temp  
Delicate  
3
4
6
2
5
7
8
1
1. Press "Power On/Off" button to power on  
Turn on the power switch, the computer board beeps once and the dryer transfers  
from off status to the initial operating status (Normal program);  
If no "Start/Pause" button is pressed in 5 min after powering on, it automatically  
cuts off power and returns to off status;  
It returns to off status immediately upon end of a cycle;  
Whatever status the computer board is (start, pause, alarm etc.), Pressing  
"Power On/Off" button will stop all operations and it enters off status.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Various button initial status for "Normal program"  
Softer  
Cycle Signal  
Wrinkle Care  
Cycles  
Off  
Normal  
Indicate current program remaining time  
Nixie display  
Temp  
High  
More Dry  
Auto-program  
Dryness Level  
Timed/Cycles  
2. Press "Cycles" button to select a suitable full automatic cycle  
The Normal program will be automatically selected after powering on. If other  
full automatic program is desired, press "Auto-program Selection" button  
until corresponding indicator turns on.  
Customer  
Normal  
Bulky Items  
Heavy Duty  
Cotton  
Casual  
Cycles  
Delicate  
Initial status of various buttons when setting "Auto-program Selection".  
Cycles Normal Heavy Duty Cotton Delicate Casual Bulky Items  
Wrinkle Care To be used together with reserve function, off if reserve is disabled  
Cycle Signal  
Delay Start  
Timed/ Cycles  
Temp  
Softer  
Indicate current selected program remaining time  
Auto Dry  
High  
High  
High  
More Dry  
Low  
Middle Middle  
Dryness Level  
Notes: If "Customer" is selected, various buttons will indicate previous conditions  
set by the user.  
"Customer" function is a program designed to facilitate user's operation. It can  
memorize programs defined by user himself and display the previous program  
upon next application of this function.  
Use details are as follows:  
After powering on, press "Cycles" until "Customer" status, then set "Cycles" to  
Timed Dry or Rack Dry, and set status of other buttons. Press "Start/Pause" button  
or after half a minute, the program defined by user himself will be stored and  
will be directly displayed upon next use.  
Notes: Pressing "Dryness Level" button will be inactive during use of "Customer"  
function.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Press "Dryness Level" button to select a suitable drying time  
After powering on, the clothes dryer automatically sets dryness at "More Dry",  
which means the normal drying time. If other drying time is desired, press  
"Dryness Level" button to select a shorter time.  
4. Press "Temp" button to set a suitable drying temperature  
After switching on, the dryer sets corresponding temperature adapting to  
different program selected. If other drying temperature is wanted, press  
"Temp" button to enable such a selection.  
5. Press "Cycle Signal" button, you will be reminded up upon  
end of a cycle  
After switching on, the dryer automatically sets buzzer at "Softer", while the  
user may define three prompt sound conditions "Louder", "Softer" and "Off".  
6. Press "Delay Start" button to select a suitable reserved drying  
program  
After powering on, the dryer delay start drying program automatically sets as disabled.  
When you desire a drying cycle ends at a delay time, press "Delay Start" button to  
set delay start drying program. After initial pressing, the nixie display indicates 3 hrs,  
which will be increased until 24 hrs by an increment 1 hr with every pressing. Press  
again will display drying time. Here if press again, it will repeat from 3 hrs. If keep  
pressed for 1.5 s, nixie display will increase continuously.  
When "Delay Start" is enabled, your selected program indicator turns off while  
"Delay Start" indicator and remaining reservation time indication turn on. During  
reserved period, pressing "Delay Start" button can indicate reserve status.  
To change operating program or cancel delay, you should cut off the supply and  
re-select.  
7. Press "Wrinkle Care" button to select wrinkle-proof drying mode  
Wrinkle Care automatically sets "Off" upon powering on. Press "Wrinkle Care"  
button, it sets wrinkle Care drying mode.  
Notes:  
"Delay Start" drying cycle ends, clothes remained in hot drum is prone to creasing.  
Wrinkle Care function operates in tumbling clothes by intermittently rotating drum  
"Wrinkle Care" function is provided to match "Delay Start" program. When  
a
"
"
to avoid clothes wrinkling.  
8. Press "Start/Pause" button  
If starting the machine, firstly close the front door and then press this button.  
If pause is needed during machine operating, press this button. Pressing again will  
resume operation.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Timed Dry cycle  
Time Remaining(Min)  
Time On(Hour)  
More Time  
Power  
On/Off  
Dry  
More Dry  
Cool down  
On  
Off  
Delay  
Start  
High  
Less Time  
Louder  
Softer  
Off  
Cycle completed  
Extend tumble  
Start  
Customer  
Normal  
Medium  
Low  
Auto Dry  
Timed Dry  
Rack dry  
Pause  
Bulky Items  
Less Dry  
Wrinkle  
Care  
Air Only(No Heat)  
Cycle  
Signal  
Dryness  
Level  
Heavy Duty  
Cotton  
Casual  
Timed  
Cycles  
Cycles  
Temp  
Delicate  
4
5
2
6
7
8
1
3
1. Press "Power On/Off" button to power on  
2. Press "Timed/Cycles" button and select "Timed Dry" cycle  
After powering on, press "Timed/Cycle" button to select "Timed Dry" program.  
3. Press "More Time" And "Less Time" buttons to set a suitable time  
After setting "Timed/Cycle" to "Timed Dry" , you can press these two buttons to  
increase or decrease drying time as you desires.  
4-7. Press buttons "Temp", "Cycle Signal", "Delay Start", and "Wrinkle  
Care" to define your desired program  
Notes: For "Timed Dry" program, use of buttons "Temp", "Cycle Signal", "Delay  
Start" and "Wrinkle Care" is the same as for auto-programs. "Dryness Level" is  
here inactive, pressing of which will get alarms.  
8. Press "Start/Pause" button  
Rack Dry cycle  
Time Remaining(Min)  
More Time  
Power  
Dry  
Time On(Hour)  
More Dry  
On/Off  
Cool down  
Cycle completed  
Extend tumble  
On  
Off  
Delay  
Start  
High  
Less Time  
Louder  
Softer  
Off  
Start  
Customer  
Normal  
Medium  
Low  
Auto Dry  
Timed Dry  
Rack dry  
Pause  
Bulky Items  
Less Dry  
Wrinkle  
Care  
Air Only(No Heat)  
Cycle  
Signal  
Dryness  
Level  
Heavy Duty  
Cotton  
Casual  
Timed  
Cycles  
Cycles  
Temp  
Delicate  
4
5
2
6
7
8
1
3
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Press "Power On/Off" button to power on  
2. Press "Timed/Cycles" button and select "Rack Dry" cycle  
After powering on, press "Timed/Cycle" button to select "Rack Dry" program.  
3. Press "More Time" And "Less Time" buttons to set a suitable time  
After setting "Timed/Cycle" to "Rack Dry" , you can press these two buttons to  
increase or decrease drying time as you desires.  
4-7. Press buttons "Temp", "Cycle Signal", "Delay Start", and "Wrinkle  
Care" to define your desired program  
Notes: For "Rack Dry" program, use of buttons "Temp", "Cycle Signal", "Delay  
Start" and "Wrinkle Care" is the same as for auto-programs. "Dryness Level" is  
here inactive, pressing of which will get alarms.  
8. Press "Start/Pause" button  
Other Features  
Your dryer also has the following features for your convenience:  
Lint Filter:  
All dryers come with a lint filter that needs to be cleaned before or after  
every Use ( read CareandCleaningGuide Section).  
Leveling Legs:  
Your dryer has four leveling legs which are located in the front and rear  
corners of your dryer. After installingyour dryer in its final position,  
you can level your dryer.  
Leveling legs can be adjusted by turning them clockwise to raise your  
dryer or by turning them counterclockwise to lower your dryer.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Normal Operating Sounds  
The following sounds are normally heard during the operation of the dryer.  
Tumbling sounds: This is normal as the heavy wet clothes in the dryer  
are continuously being tossed around.  
Air rushing noise: This happens as the dryer drum spins at very high  
RPM and the air is rushing through the dryer drum.  
Tips  
For bestdrying results, cleanthelint filter beforeandafter every use.  
Do not overload the dryer.  
Balance the dryer load, evenly Throughout the dryer for the best results.  
Drying time depends on many variables: load size, type of fabric and  
moisture in it, heat and moisture in the room, electric voltage, length of  
the venting duct, etc.  
Always follow the fabric care instructions supplied by the garment man-  
ufacturer.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Care and Cleaning Guide  
Lint filter needs to be cleaned before and after each use for your unit to  
Operate at optimum efficiency. The filter can be slid out, by pulling on  
The tab located on the inside of the dryer door. The filter may be  
Washed or vacuumed. Remove the excess water from the filter by  
Gently shaking the filter. This will remove dust and particles trapped in  
The filter. Lint build-up in screen restricts airflow, which causes longer  
Drying times. After cleaning, slide the filter back in place. DO NOT  
USE YOUR DRYER WITHOUT THE LINT FILTER.  
lint filter  
Do not useany typeof spray cleaner whencleaning theinterior .  
Hazardous fumesor Electric shock could occur If dyr er drum becomes  
stained,clean the drumwith a dampcloth.Removeany residue befoer  
drying the next load.  
Clean cabinet with mild soap andwater. Do not use harsh or abrasive  
cleaners,this could damage the dryer.  
Clean the duct and theventon a regular basis to avoid clogging which  
could affect the efficiency of the dryer.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Dryer does not operate:  
Check if unit is plugged in. The plug may have come loose.  
Check if the electrical wall socket is the correct voltage.  
Check if the circuit breaker needs to be reset or if the fuse  
needs to be replaced.  
Check if the unit is in Off mode. Press Power On/Off button again.  
Check if door is open or not in place. Open and close the door slightly  
and make sure in place.  
Dryer is working but not drying the clothes:  
Unit may be over loaded. The dryer drum should only be half full.  
Check exhause ducts and vent. Vent should be free of all obstructions.  
Duct should be lint and dust free. Ducts should be cleaned regularly.  
Dryer load needs to be resorted. Heavy clothes may need to  
be separated from regular clothes.  
Bulky clothes may require repositioning.  
If clothes dry unevenly a higher dry setting may be required or  
clothes in the dryer may need to be resorted.  
Dryer making noise when drying:  
Coins, loose change, buttons and other heavy objects could make noise.  
Dryer may need to be leveled properly.  
Read OPERATING INSTRUCTION-Normal Operating Sounds.  
Static:  
Caused by over drying. Adjust for shorter drying time.  
Mixed with synthetic fabric. Sort and separate different fabrics.  
Use a fabric softener.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION INSTRUCTIONS  
Select a suitable location for the dryer on a hard even surface away from direct  
sunlight or heat source e.g. radiators, baseboard heaters, cooking appliances etc.  
Any floor unevenness should be corrected with the leveling legs located on the  
bottom of the dryer.  
Tools and Materials Required  
Phillips head and flathead screwdrivers  
Channel-lock adjustable pliers  
1/2 inch open end wrench  
Spirit level  
Measuring tape (12ft. Min.)  
Duct tape  
Rigid or flexible metal 4 inch (10.2 cm) duct  
Vent hood  
Electrical Requirements  
Power Supply:  
3 wire, 220V Volt, 30 Amp, 50Hz, 1 Phase  
Power Supply Cord Kit:(not supplied when sold)  
The dryer MUST employ a 3-conductor power supply cord NEMA(245IEC66  
450V/750V) rated at 220 Volt AC minimum, 30 Amp., with 3 open end  
spade lug connectors with upturned ends or closed loop connectors and  
marked for use with clothes dryers.  
Unpacking Your Dryer  
1. Remove all packaging material. This includes the foam base and all  
adhesive tape holding the dryer accessories inside and outside.  
2. Inspect and remove any remains of packaging, tape or printed  
materials before using the dryer.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Exhaust System Connections  
Requirements and Instructions  
1. Do not use plastic flexible duct to exhaustthe dryer. Excessive lint can build up  
inside system and create a fire hazard and restrict air flow. Restricted airexhaust  
flow will increase dryer times. If your present system is made up of plastic duct or  
metal foil duct, replace it with a rigid or flexible metal duct. Ensure present duct  
is free of any lint prior to installing dryer duct.  
2. If the dryer is not exhausted out doors, some fine lint will be expelled  
into the laundry area. An accumulation of lint in any area of the home can  
create a health and fire hazard. To reduce risk of fire, dryer MUST BE  
EXHAUSTED OUTDOORS.  
3. Do not allow combustible material (for example: clothing,  
draperies/curtains, paper) to come in contact with venting system. The dryer  
must not be exhausted into a chimney, a wall, a ceiling, or any concealed space  
of a building which can accumulate lint, resulting in a fire hazard.  
4. Exceeding the length of duct pipe or number of elbows allowed in  
the "Maximum Length" charts can cause an accumulation of lint in  
the exhaust system. Plugging the system could create a fire hazard,  
as well as increase drying times.  
5. Do not screen the exhaust ends of the vent system, nor use any screws  
or rivets to assemble the exhaust system. Lint can become caught in the screen,  
on the screws or rivets, clogging the duct work and creating a fire hazard as well  
as increasing drying times. Use an approved vent hood to terminate the duct out-  
doors, and seal all joints with duct tape. All male duct pipe fittings must be  
installed downstream with the flow of air.  
Explosion hazard:  
Do not install the dryer where gasoline or other flammables are kept or stored.  
If the dryer is installed in a garage, it must be minimum of 18 inches (45.7 cm)  
above the floor. Failure to do so can result in death, explosion, fire or burns.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Materials  
Use only 4 inch (10.2 cm) diameter (minimum) rigid or flexible metal duct and  
approved vent hood which has a swing-out damper cover open when the dryer is in  
operation. When the dryer stops, the dampers automatically close to prevent drafts  
and the entrance of insects and rodents. To avoid restricting the outlet, maintain a  
minimum of 12 inches (30.5 cm) clearance between the vent hood and the ground  
or any other obstruction. The vent flap should be able to move freely.  
MAXIMUM EXHAUST LENGTH  
INSTALL MALE FITTINGS IN THE CORRECT DIRECTION  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
After installation is completed, the following method must be used to  
determine if the exhaust system is acceptable:  
1. Connect an inclined or digital manometer between the dryer and the  
point the exhaust system connects to the dryer.  
2. Set the dryer cycle and temperature to cool down,  
and start the dryer.  
3. Read the measurement on the manometer.  
4. The system back pressure must not be higher than 0.75 inches  
of water column. If the system back pressure is less than 0.75  
inches of water column, the system is acceptable. If the manometer  
reading is higher than 0.75 inches of water column, the system is too  
restrictive and the installation is unacceptable.  
Although vertical orientation of the exhaust system is acceptable, certain  
extenuating circumstances could affect the performance of the dryer:  
1. Only the rigid metal duct work should be used.  
2. Venting vertically through a roof may expose the exhaust system to  
down drafts causing an increase in vent restriction.  
3. Running the exhaust system through an area not insulated may cause  
condensation and faster accumulation of lint.  
4. Compression or crimping of the exhaust system will cause an increase  
in vent restriction.  
The exhaust system should be inspected and cleaned a minimum of every  
18 months with normal usage. The more the dryer is used, the more often  
you should check the exhaust system and vent hood for proper operation.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Location of Your Dryer  
Do Not Install Your Dryer:  
In an area exposed to dripping water or outside weather conditions.  
In an area where it will come in contact with curtains, thick carpet,  
or anything that will obstruct the flow of combustion and ventilation air.  
On carpet. Floor must be solid with a maximum slope of 1inch (2.54 cm).  
Installation in Recess or Closet:  
A dryer installed in a bedroom, bathroom, recess or closet, must be  
exhausted outdoors.  
Your dryer needs the space around it for proper ventilation.  
A minimum of 120 square inches (774.2 square cm) of opening,  
equally divided at the top and bottom of the door, is required. Air  
openings are required to be unobstructed when a door is installed. A  
louvered door with equivalent air openings for the full length of the  
door is acceptable.  
DIMENSIONS  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation in Mobile Home  
Dryer must be exhausted outside (outdoors, not beneath the mobile  
home) using metal ducting that will not support combustion.  
Metal ducting must be 4 inches (10.16 cm) in diameter with  
no obstructions. Rigid metal duct is preferred.  
If dryer is exhausted through the floor and area beneath the  
mobile home is enclosed, the exhaust system must terminate  
outside the enclosure with the termination securely fastened to the  
mobile home structure.  
Refer to previous pages for other important venting requirements.  
Installation must conform to current Manufactured Home  
Construction & Safety Standard.  
Correct  
Incorrect  
Correct  
Incorrect  
Correct  
Incorrect  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Electrical Connections  
Requirements and Instructions  
1. This appliance must be properly grounded. Electrical shock can result if the  
dryer is not properly grounded. Follow the instructions in this manual  
for proper grounding.  
2. Do not use an extension cord with this dryer. Some extension cords are not  
designed to withstand the amounts of electrical current this dryer utilizes and  
can melt, creating electric shock and/or fire hazard. Locate the dryer within  
reach of the receptacle for the length of power cable to be purchased,  
allowing some slack in the cord. Refer to the electrical requirements  
in this manual for the proper power cord to be purchased.  
3. A approve strain relief must be installed onto power cable. If the the strain  
relief is not attached, the cord can be pulled out of the dryer and can be cut  
by any movement of the cord, resulting in electrical shock.  
4. Do not use an aluminum wire receptacle with copper wired power  
cord and plug (or vice versa). A chemical reaction occurs between  
copper and aluminum and can cause electrical shorts. The proper wiring  
and receptacle is a copper wired power cord with a copper wired receptacle.  
Danger: Improper connection of the equipment grounding conductor  
can result in a risk of electrical shock. Check with a qualified  
electrician if you are in doubt as to whether the appliance is  
properly grounded.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3-Wire Cord Connections  
G
N
tighten nut  
to these threads  
nut  
L
power cord  
Strain relief  
mounting bracket  
1. Remove the screws securing the terminal block access cover  
and the strain relief mounting bracket located on the back of the  
dryer in the upper corner.  
2. Install a strain relief into the power cord entry hole of the  
mounting bracket. Finger tighten the nut only at this time.  
3. Thread a 30 Amp. Power cord, 245 IEC66(YCW) 450V/750V,  
through the strain relief.  
4. Attach the power cable earthconductor to the silver  
coloured centre terminal on the terminal block. Tighten  
the screw securely.  
5. Attach the remaining two power cable outer conductors to the  
outer silver coloured terminals on the terminal block. Tighten both  
screws securely. Warning:Do not make a sharp bend or crimp  
wiring/conductor at connections.  
6. Reattach the strain relief mounting bracket to the back of the dryer  
with two screws. Tighten screws securely.  
7. Tighten the screws securing the cable restraint firmly against the  
power cable.  
8. Tighten the tension relief nut securely so that the tension relief  
does not turn.  
9. Reinstall the terminal block cover.  
Grounding This appliances must be connected to a ground metal,  
permanent wiring system, or an equipment-grounding  
conductor must be run with the circuit conductors and  
connected to the equipment-grounding terminal or  
lead on the appliance.  
instruction:  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING-improper connection of the equipment-grounding conductor  
can result in a risk of electric shock. Check with a qualified electrician or  
service representative or personnel if you are in doubt as to whether the  
appliance is properly grounded.  
Caution: Label all wires prior to disconnection, when servicing controls.  
Wiring errors can cause improper operation and be  
dangerous. Check unit for proper operation after servicing.  
Warning: Discard or destroy the carton and plastic bags after the  
dryer is unpacked. Children should not be allowed to use  
them to play with. Cartons covered with rugs,  
bedspreads, or plastic sheets can become an airtight chamber  
and cause suffocation leading to death. Make all packing  
materials inaccessible to children.  
Warning: The instructions in this manual and all other literature  
included with this dryer can not cover every possible  
condition and situation that may occur. Good safety practice  
and caution must be applied when installing, operating and  
maintaining any appliances. After installing, if you are in  
doubt, call a qualified electrician to install and wire the dryer.  
Specifications  
Model  
GDZ22-2  
220V~ 50Hz  
10 kg  
Rated voltage , frequency  
Rated dry capacity  
Rated dry power  
Weight (about)  
Dimension  
4800W  
55 kg  
L712mm W686mm H1115mm  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Graco Car Seat PD156938D User Manual
Grandstream Networks Telephone GXP Series User Manual
Haier Freezer BD 66A User Manual
Harbor Freight Tools Grinder 30304 User Manual
Harman Kardon Music Mixer TU 970 User Manual
Hotpoint Double Oven 18M 0712 A P962 User Manual
HP Hewlett Packard Personal Computer t5545 User Manual
HP Hewlett Packard Printer T1100 User Manual
Imation Printer 134000 User Manual
Impex Home Gym PM 4500 User Manual