Hotpoint Washer Dryer AQM8L 29 I User Manual

Instructions for

installation and use

WASHER DRYER

This symbol reminds you to read this instruction manual.

Contents

English,1

Installation, 2-3-4-5

Unpacking and levelling

Connecting the electricity and water supplies

Technical data

Description of the machine, 6-7

Control panel

How to run a wash cycle or a drying cycle, 8-9

Wash cycles and options, 10

Table of wash cycles

Wash options

AQUALTIS

Detergents and laundry, 11

Detergent

Preparing the laundry

Washing recommendations

Load balancing system

AQM8L 29 I

Precautions and tips, 12

General safety

Disposal

Opening the porthole door manually

Care and maintenance, 13

Cutting off the water and electricity supplies

Cleaning the machine

Cleaning the detergent dispenser drawer

Caring for your appliance drum

Cleaning the pump

Checking the water inlet hose

Trouble shooting, 14-15

Assistance, 16-17

Download from Www.Somanuals.com. All Manuals Search And Download.

• the supply voltage is included within the values indica-

Connecting the drain hose

ted on the Technical Data Plate fixed on the machine;

Connect the drain hose,

without bending it, to a

draining duct or a wall

drain situated between

65 and 100 cm from the

floor;

• the socket is compatible with the washing machine’s plug.

If this is not the case, replace the socket or the plug.

Your appliance is now supplied with a 13 amp fused plug

it can be plugged into a 13 amp socket for immediate use.

Before using the appliance please read the instructions

below.

65 - 100 cm

WARNING - THIS APPLIANCE MUST BE EARTHED.

THE FOLLOWING OPERATIONS SHOULD BE CARRIED

OUT BY A QUALIFIED ELECTRICIAN.

The drain hose may

be connected to an

Replacing the fuse:

under-sink trap. Before

connecting the drain

hose from the machine

ensure that any blanks

or removable ends have

been taken off the spigot.

When replacing a faulty fuse, a 13 amp ASTA approved

fuse to BS 1362 should always be used, and the fuse

cover re-fitted. If the fuse cover is lost, the plug must not

be used until a replacement is obtained.

Where it connects to

the waste water pipe

cut end off spigot or

remove the blanking cap

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of the

correct colour as indicated by the coloured marking or the

colour that is embossed in words on the base of the plug.

Replacements can be obtained directly from your nearest

Service Depot.

If it is placed over the

edge of a basin or sink

be sure the free end of

the hose should not be

underwater.

Removing the plug:

If your appliance has a non-rewireable moulded plug

and you should wish to re-route the mains cable through

partitions, units etc., please ensure that either:

the plug is replaced by a fused 13 ampere rewireable plug

bearing the BSI mark of approval.

or:

the mains cable is wired directly into a 13 amp cable outlet,

controlled by a switch, (in compliance with BS 5733) which

is accessible without moving the appliance.

! We advise against the use of hose extensions; in case

of absolute need, the extension must have the same

diameter as the original hose and must not exceed 150

cm in length.

Ensure that if the drain hose is pushed into a standpipe,

that the end does not go down more than 15cms (6

inches). If the hose is pushed down too far, this may

cause the machine to self -syphon ie. continuously

empty as it is filling.

Disposing of the plug:

Ensure that before disposing of the plug itself, you make

the pins unusable so that it cannot be accidentally inserted

into a socket.

Instructions for connecting cable to an alternative plug:

Important: the wires in the mains lead are coloured in

accordance with the following code:

Electric connection

Green & Yellow Earth

Before plugging the appliance into the mains socket,

make sure that:

Blue

Neutral

Live

Brown

• the socket is earthed and in compliance with the

applicable law;

• the socket is able to sustain the appliance’s

maximum power load indicated in the Technical details

table (see page 5);

Download from Www.Somanuals.com. All Manuals Search And Download.

As the colours of the wires in the lead may not correspond

with the coloured markings identifying the terminals in your

plug, proceed as follows:

Connect Green & Yellow wire to terminal marked E or

coloured Green or Green & Yellow.

Connect Brown wire to terminal marked L or coloured Red.

Connect Blue wire to terminal marked N or coloured Black.

If a 13 amp plug (BS 1363) is used it must be fitted with a

13 amp fuse, either in the plug or adaptor or at the

distribution board.

If you are in any doubt regarding the electrical supply to your

machine, consult a qualified electrician before use.

How to connect an alternative plug:

The wires in this mains lead are coloured in accordance with

the following code:

BLUE

BROWN

NEUTRAL (N)

LIVE (L)

GREEN & YELLOW

EARTH (E)

GREEN &

YELLOW

13 ampere fuse

BROWN

BLUE

CROSS-BAR

CORD GRIP

Disposing of the appliance:

When disposing of the appliance please remove the plug

by cutting the mains cable as close as possible to the plug

body and dispose of it as described above.

! The washing machine should not be installed in an outdoor

environment, not even where the area is sheltered, because

it may be very dangerous to leave it exposed to damp, rain

and thunderstorms.

! When the washer dryer is installed, the mains socket must

be within easy reach.

! Do not use extensions or multiple sockets.

! The power supply cable must never be bent or

dangerously compressed.

! The power supply cable must only be replaced by an

authorised serviceman.

Warning! The company denies all liability if and when these

norms are not respected.

Download from Www.Somanuals.com. All Manuals Search And Download.

Technical data

Model

AQM8L 29 I

width 59.5 cm

height 85 cm

depth 64.5 cm

Dimensions

Capacity

from 1 to 8 kg for the wash programme

from 1 to 6 kg for the drying programme

Electrical

please refer to the technical data plate

fixed to the machine

connections

maximum pressure 1 MPa (10 bar)

Water connections minimum pressure 0.05 MPa (0.5 bar)

drum capacity 62 litres

Spin speed

up to 1200 rotations per minute

Wash: programme

; temperature 60°C;

using a load of 8 kg.

Energy rated

programmes

according to

regulation

Drying: first drying cycle performed with

2 kg load, by selecting the “Iron dry”

dryness level.;

the second drying cycle performed with

6 kg load, by selecting the “Cupboard

dry” dryness level.

EN 50229

This appliance conforms to the following

EC Directives:

- 2004/108/EC (Electromagnetic Compatibility)

- 2006/95/EC (Low Voltage)

- 2002/96/EC

Download from Www.Somanuals.com. All Manuals Search And Download.

Description of the machine

CONTROL

PANEL

PORTHOLE DOOR

HANDLE

KICK STRIP

ADJUSTABLE FEET

PORTHOLE DOOR

1. pre-wash compartment:

use powder detergent.

2. main wash compartment:

use powder or liquid

Always use the handle to

open the porthole door (see

figure).

detergent. If using the

latter type of detergent, we

recommend it is poured into

the drawer immediately before

you start the washer dryer.

washing additives compartment: for fabric softener

or liquid additives. We recommend that the maximum

level indicated by the grille is not exceeded, and that

concentrated fabric softeners are diluted.

DETERGENT DISPENSER DRAWER

The detergent dispenser

drawer is located inside

the machine and can be

accessed by opening the

door.

For more information on

detergent measures, please

refer to the chapter entitled

“Detergents and laundry”.

Standby mode

This washer dryer, in compliance with new energy saving

regulations, is fitted with an automatic standby system

which is enabled after about 30 minutes if no activity is

detected. Press the ON-OFF

the machine to start up again.

button briefly and wait for

Download from Www.Somanuals.com. All Manuals Search And Download.

Control panel

DRYING

buttons with

WASH

CYCLE

PHASE

icons

DELAY TIMER

buttons with indicator lights

indicator lights

TEMPERATURE

buttons with indicator lights

ECO indicator light

START/PAUSE

button with indicator

light

OPTION buttons

with indicator lights

OPTION buttons with

WASH CYCLE

SELECTOR knob

indicator lights

CHILD LOCK button

with indicator light

DELAY

TIMER

Button with ON/OFF

indicator light

TEMPERATURE button

DOOR LOCKED

indicator light

button

DRY

button

START/PAUSE button with indicator light: when the green

indicator light flashes slowly, press the button to start a

wash cycle. Once the cycle has begun the indicator light

will remain lit in a fixed manner. To pause the wash cycle,

press the button again; the indicator light will flash in an

Button with

ON/OFF indicator light: press this briefly

to switch the machine on or off. The green indicator light

indicates that the machine is switched on. To switch off

the washer dryer during the wash cycle, press and hold

the button for approximately 3 seconds; if the button is

pressed briefly or accidentally the machine will not switch

off. If the machine is switched off during a wash cycle, this

wash cycle will be cancelled.

orange colour. If the “Door locked”

indicator light is

switched off, the door may be opened. To start the wash

cycle from the point at which it was interrupted, press the

button again.

WASH CYCLE SELECTOR knob: may be turned in

either direction. To select the most suitable wash cycle,

please refer to the “Table of wash cycles”.

DOOR LOCKED

indicator light: indicates that the

porthole door is locked. To open the door, pause the wash

cycle (see “Running a wash cycle”).

The knob will not move during the wash cycle.

CHILD LOCK

button with indicator light: to activate

TEMPERATURE

button: press to modify or exclude

or deactivate the CHILD LOCK, press and hold the button

for approximately 2 seconds. when the indicator light

is illuminated, the control panel is locked. This means it

is possible to prevent wash cycles from being modified

accidentally, especially where there are children in the

home.

the temperature setting; the value will be identified by the

indicator lights above it (see “Running a wash cycle”).

DRY button

: press to decrease or exclude drying;

the selected drying level or time will be identified by the

indicator lights above it (see “How to run a wash cycle or a

drying cycle”).

ECO indicator light: the

icon lights up when, after

DELAY TIMER

for the selected wash cycle; the set delay time will appear

on the display above (see “Running a wash cycle”).

button: press to set a DELAY TIMER

altering the washing parameters, an energy saving of

at least 10% is made. Furthermore, before the machine

enters “Standby” mode, the icon will light up for a few

seconds; when the machine is switched off the estimated

energy saving will be around the 80% mark.

OPTION buttons with indicator lights: press to select the

available options. The indicator light corresponding to the

selected option will remain lit (see “Running a wash cycle”).

WASH CYCLE PHASE icons: these illuminate to indicate

the progress of the wash cycle (Wash

– Rinse

–

Spin/Drain

The text

– Drain

lights up when the cycle is complete.

Download from Www.Somanuals.com. All Manuals Search And Download.

Running a wash cycle

WARNING: before you use the washer dryer for the first

time, run a wash cycle with detergent and no laundry, using

the 90° cottons cycle without pre-wash.

Iron dry: slightly damp clothes, easy to iron.

Cupboard dry: suitable for laundry which can be put

back in a cupboard without being ironed.

If your laundry load to be washed and dried is much

greater than the maximum stated load (see below

table), perform the wash cycle, and when the cycle

is complete, divide the garments into groups and put

some of them back in the drum. At this point, follow the

instructions provided for a “Drying only” cycle. Repeat

this procedure for the remainder of the load.

N.B: a cooling-down period is always added to the end

of each drying cycle.

1. SWITCH THE MACHINE ON. Press the

All the indicator lights will illuminate for 1 second; the

indicator light corresponding to the button will then

button.

remain lit in a fixed manner and the START/PAUSE

indicator light will flash slowly.

2. LOAD THE LAUNDRY. Open the porthole door.

Load the laundry, making sure you do not exceed the

maximum load value indicated in the table of wash

cycles on the following page.

Drying only

Use the cycle selector knob to select a drying cycle

( - - ) in accordance with the type of fabric. The

desired drying level or time may also be set using the

3. MEASURE OUT THE DETERGENT. Pull out the

detergent dispenser drawer and pour the detergent into

the relevant compartments as described in “Description

of the machine”.

DRYING button

Table of drying times (guideline values)

Fabric

type

Max.

load (kg) dry

Cupboard Iron

4. CLOSE THE PORTHOLE DOOR.

Load type

dry

Clothing of diffe-

rent sizes, Terry

towels

5. SELECT THE PROGRAMME. Turn the WASH CYCLE

SELECTOR KNOB right or left, until you have selected

the desired wash cycle. A temperature and spin speed

is set for each wash cycle; these may be adjusted.

Cotton

200

150

Sheets, Shirts, Py-

jamas, socks, etc.

Synthetics

Wool

140

160

120

130

6. CUSTOMISE THE WASH CYCLE. Use the relevant

Knitwear, Pullo-

vers. etc.

buttons on the control panel:

1.5

Modify the temperature.

The information contained in the table is purely indicative.

The machine automatically displays the maximum

temperature values set for the selected cycle, or the

most recently-used settings if they are compatible with

the selected cycle. The temperature can be decreased

Set a DELAY TIMER.

To set the “delay timer” option for the program you have

selected, press the button until the indicator light for the

desired delay time is illuminated.

by pressing the

button, until the cold wash “

“

setting is reached. If these buttons are pressed again,

the maximum values are restored.

! Exception: if the “Cotton” programme is selected, the

temperature can be increased up to a value of 90°C.

The sixth time the button is pressed, the function will be

disabled.

N.B.: once the START/PAUSE button is pressed the

“delay timer” indicator light will flash

(the time delay value may only be changed by

decreasing the time).

Setting the drying cycle

The first time the button is pressed, the machine will

automatically select the maximum drying cycle which is

compatible with the selected wash cycle. Subsequent

presses will decrease the drying level and then the

drying time, until the cycle is excluded completely ( ).

If these buttons are pressed again, the maximum values

are restored.

Modify the cycle settings.

Press the OPTION buttons to customise the wash cycle

in accordance with your own requirements.

• Press the button to activate the option; the

corresponding indicator light will switch on.

• Press the button again to disable the option; the

Two types of drying may be selected:

A - Based on a set time period: between 60’ and 180’.

B - Based on the how damp the clothes are once they

have been dried:

indicator light will switch off.

! If the selected option is not compatible with the

selected wash cycle, this incompatibility will be signalled

by the flashing of the indicator light; the option will not

be activated.

Download from Www.Somanuals.com. All Manuals Search And Download.

! If the selected option is not compatible with another

option that has been selected previously, the indicator

light corresponding to the first option selected will

flash and only the second option will be activated; the

indicator light corresponding to the button will remain lit

in a constant manner.

7. START THE PROGRAMME. Press the START/PAUSE

button. The corresponding indicator light remains lit in

a fixed manner and the porthole door locks (the

DOOR LOCKED indicator light illuminates). The icons

corresponding to the wash cycle phases will light up

during the cycle to indicate which phase is currently in

progress. To change a wash cycle once it has already

started, pause the washer dryer by pressing the START/

PAUSE button; then select the desired cycle and press

the START/PAUSE button again. To open the door

during a wash cycle, press the START/PAUSE button;

if the DOOR LOCKED

indicator light is switched off

you may open the door. Press the START/PAUSE button

again to restart the wash cycle from the point at which it

was interrupted.

8. THE END OF THE WASH CYCLE. This is indicated

by the illuminated text END. The porthole door may be

opened immediately. If the START/PAUSE indicator light

is flashing, press the button to end the cycle. Open the

door, unload the laundry and switch off the machine.

! If you wish to cancel a cycle which has already begun,

press and hold the

button until the cycle stops and the

machine switches off.

Download from Www.Somanuals.com. All Manuals Search And Download.

Wash cycles and options

Table of wash cycles

Detergent and additives

Max.

speed Drying

(rpm)

Max.

load

(kg)

Max. temp.

(°C)

Cycle

duration

Icon Description of the wash cycle

Fabric

Prewash Wash

softener

Cottons wash cycles

Cottons with pre-wash

(Add detergent to the relevant compartment).

90°

1200



184

160

60°

(Max. 90°C)

Cotton (1): heavily soiled whites and resistant colours.

Cotton (2): heavily soiled whites and delicate colours.

40°

1200



147

Coloured Cotton (3)

Special wash cycles

* Steam Refresh (see next page).

1,5

Baby: heavily soiled delicate colours

40°

800



118

Mix 30': to refresh lightly soiled garments quickly (not suita-

ble for wool, silk and clothes which require washing by hand)

30°

800



3,5

Durable Synthetics

60°

30°

40°

800



3,5

Silk: for garments in silk and viscose, lingerie.

Wool: for wool, cashmere, etc.

Drying cycles

600



Wash & dry

30°

1200



Cotton dry

Synthetics dry

Wool dry

Partials cycles

Rinse



3,5

1,5

1200



Spin

Drain

The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary

according to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options

selected.

For all Test Institutes:

1) Test wash cycle in compliance with regulation EN 50229: set wash cycle

with a temperature of 60°C.

2) Long wash cycle for cottons: set wash cycle

3) Short wash cycle for cottons: set wash cycle

with a temperature of 40°C.

Wash options

Steam Hygiene

For the best washing results we recommend the usage of a

liquid detergent.

This option enhances washing performance by generating

steam during the wash cycle that eliminates any bacteria

from fibres while treating them at the same time. Place the

laundry in the drum, choose a compatible programme and

select option “ “.

! It cannot be used in conjunction with

Time Saver

If you select this option, the wash cycle duration will be

reduced by 30%-50%, depending on the selected cycle,

thereby guaranteeing simultaneous water and energy

saving. Use this cycle for lightly soiled garments.

! The steam generated during washer dryer operation may

cause the porthole door to become hazy.

! It cannot be used in conjunction with

(90°C),

! It cannot be used in conjunction with

Slow Spin

Press this button to reduce the spin speed.

!Itcannotbeusedinconjunctionwith

Eco Option

The Eco Wash function saves energy by not heating the

water used to wash your laundry – an advantage both to

the environment and to your energy bill. Instead, intensified

wash action and water optimisation ensure great wash

results in the same average time of a standard cycle.

Download from Www.Somanuals.com. All Manuals Search And Download.

Detergents and laundry

Baby: use the special “Baby” wash cycle to remove

Detergent

the remove the soiling typically caused by babies, while

removing all traces of detergent from nappies in order to

prevent the delicate skin of babies from suffering allergic

reactions. The cycle has been designed to reduce the

amount of bacteria by using a greater quantity of water

and optimising the effect of special disinfecting additives

added to the detergent. At the end of the wash cycle, the

machine will slowly rotate the drum; to end the cycle press

the START/PAUSE button.

The type and quantity of detergent required depend on

the type of fabric you are washing (cotton, wool, silk,

etc.), as well as its colour, the washing temperature, the

level of soiling and the hardness of the water in the area.

Measuring out the detergent carefully will avoid wastage

and help to protect the environment: although they are

biodegradable, detergents still contain ingredients which

alter the balance of nature.

We recommend the following:

• use powder detergents for white cotton garments and

pre-washing.

• use liquid detergents for delicate cotton garments and

for all low-temperature wash cycles.

Silk: use the special “Silk”

wash cycle to wash all silk

garments. We recommend the use of special detergent

which has been designed to wash delicate clothes.

Curtains: use the “Silk”

wash cycle. Fold curtains and

place them in a pillow case or mesh bag.

• use gentle liquid detergents for wool and silk garments.

The detergent should be poured into the relevant compartment

- or the dispenser placed directly inside the drum - before the

wash cycle begins. In the latter case, it will not be possible to

select the Cottons with pre-wash cycle.

Wool: Hotpoint is the only washer dryer brand to have

been awarded the prestigious Woolmark Platinum Care

endorsement (M.0508) by the Woolmark Company, which

means that all woollen garments may be washed in the

washer dryer, even those which state “hand wash only”

on the label. The “Wool” wash cycle can be used

to wash all woollen garments in the washer dryer while

guaranteeing optimum performance.

! Do not use hand washing detergents because these

create too much foam.

Preparing the laundry

• Shake out the garments before loading them into the

Wash & Dry

was designed to wash and dry lightly

soiled garments quickly. This cycle may be used to wash

and dry a laundry load of up to 1 kg in just 60 minutes.

To achieve optimum results, use liquid detergent and pre-

treat cuffs, collars and stains.

machine.

• Divide the laundry according fabric type (symbol on the

washing instruction label) and colour, making sure you

separate the coloured garments from the white ones;

• Empty all pockets and check the buttons;

• Do not exceed the values listed in the “Table of wash cycles”,

which refer to the weight of the laundry when dry.

Load balancing system

Before every spin cycle, to avoid excessive vibrations

before every spin and to distribute the load in a uniform

manner, the drum rotates continuously at a speed which

is slightly greater than the washing rotation speed. If,

after several attempts, the load is not balanced correctly,

the machine spins at a reduced spin speed. If the load is

excessively unbalanced, the washer dryer performs the

distribution process instead of spinning. To encourage

improved load distribution and balance, we recommend

small and large garments are mixed in the load.

How much does your laundry weigh?

1 sheet

400-500 g

150-200 g

400-500 g

900-1200 g

150-250 g

400-500 g

150-200 g

1 pillowcase

1 tablecloth

1 bathrobe

1 towel

1 pair of jeans

1 shirt

Washing recommendations

* Steam Refresh

Anti-crease

This function interrupts the wash programme, and the

washing is left to soak in water before the appliance is

drained.

It is automatically activated with programme (Silk) and

helps to prevent the formation of creases.

To complete the cycle press the START/PAUSE button.

This programme refreshes garments by removing bad

odours and relaxing the fibres (1.5 kg, roughly 3 items).

Insert dry items only (that are not dirty) and select

programme “

cycle is completed, so we recommend hanging them to

dry. The “ “ programme makes ironing easier.

“. The garments will be damp once the

Moreover, with the “Steam Perfume” laundry balls, your

favourite perfume can be added to your laundry. Place a

few drops of perfume on the sponge contained inside the

laundry ball, close it and insert it into the drum together

with the laundry. Then launch the specific programme “

“. At the end of the cycle, garments will be relaxed and

fragrant.

! Not recommended for wool or silk garments.

! Do not add too much perfume to the sponge in order to

avoid it dripping.

! Do not add softeners or detergents.

Download from Www.Somanuals.com. All Manuals Search And Download.

Precautions and tips

• Do not use the appliance to dry foam rubber or

! The machine was designed and constructed in

accordance with international safety regulations. The

following information is provided for safety reasons and

must therefore be read carefully.

similar elastomers.

• Make sure that the water tap is turned on during

the drying cycles.

Disposal

General safety

• Disposing of the packaging materials: observe local

regulations so that the packaging may be re-used.

• The European Directive 2002/96/EC relating to Waste

Electrical and Electronic Equipment (WEEE) states

that household appliances should not be disposed of

using the normal solid urban waste cycle. Exhausted

appliances should be collected separately in order to

optimise the cost of re-using and recycling the materials

inside the machine, while preventing potential damage

to the atmosphere and to public health. The crossed-out

dustbin is marked on all products to remind the owner

of their obligations regarding separated waste collection.

For more information relating to the correct disposal of

household appliances, owners should contact their local

authorities or appliance dealer.

• This appliance was designed for domestic use only.

• This appliance is not intended for use by persons

(including children) with reduced physical, sensory

or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person

responsible for their safety.

Children should be supervised to ensure that they do

not play with the appliance.

- Do not dry unwashed items in the tumble dryer.

- Items that have been soiled with substances such

as cooking oil, acetone, alcohol, petrol, kerosene,

spot removers, turpentine, waxes and wax removers

should be washed in hot water with an extra amount of

detergent before being dried in the tumble dryer.

- Items such as foam rubber (latex foam), shower caps,

waterproof textiles, rubber backed articles and clothes

or pillows fitted with foam rubber pads should not be

dried in the tumble dryer.

- Fabric softeners, or similar products, should be used

as specified by the fabric softener instructions.

- The final part of a tumble dryer cycle occurs without

heat (cool down cycle) to ensure that the items are left

at a temperature that ensures that the items will not be

damaged.

Opening the porthole door manually

In the event that it is not possible to open the porthole door

due to a powercut, and if you wish to remove the laundry,

proceed as follows:

1. remove the plug from the

electrical socket.

2. make sure the water level

inside the machine is lower

than the door opening; if

it is not, remove excess

water using the drain hose,

collecting it in a bucket as

indicated in the figure.

3. remove the cover panel

on the lower front part of

the washing machine (see

WARNING: Never stop a tumble dryer before the end of

the drying cycle unless all items are quickly removed and

spread out so that the heat is dissipated.

• Do not touch the machine when barefoot or with wet or

damp hands or feet.

• Do not pull on the power supply cable when unplugging

the appliance from the electricity socket. Hold the plug

and pull.

• Do not touch the drained water as it may reach

extremely high temperatures.

• Never force the porthole door. This could damage the

safety lock mechanism designed to prevent accidental

opening.

overleaf).

4. pull outwards using the

tab as indicated in the figure,

until the plastic tie-rod is freed

from its stop position; pull

downwards until you hear a

“click”, which indicates that

the door is now unlocked.

• If the appliance breaks down, do not under any

circumstances access the internal mechanisms in an

attempt to repair it yourself.

• Always keep children well away from the appliance while

it is operating.

5. open the door; if this is

still not possible repeat the

procedure.

6. reposition the panel,

making sure the hooks are

securely in place before you

push it onto the appliance.

• If it must be moved, proceed with the help of two or

three people and handle it with the utmost care. Never

try to do this alone, because the appliance is very heavy.

• Before loading laundry into the washer dryer, make sure

the drum is empty.

• During the drying phase, the door tends to get

quite hot.

• Do not use the appliance to dry clothes that have

been washed with flammable solvents (e.g.

trichlorethylene).

Download from Www.Somanuals.com. All Manuals Search And Download.

Care and maintenance

To access the pre-chamber:

Cutting off the water and electricity

supplies

• Turn off the water tap after every wash cycle. This will

limit wear on the hydraulic system in the machine and

help to prevent leaks.

• Unplug the appliance when cleaning it and during all

maintenance work.

Cleaning the machine

1. take off the cover panel on the front of the machine by

first pressing it in the centre and then pushing downwards

on both sides until you can remove it (see figures);

The outer parts and rubber components of the appliance

can be cleaned using a soft cloth soaked in lukewarm

soapy water. Do not use solvents or abrasives.

2. position a container so that

it will collect the water which

flows out (approximately 1.5 l)

(see figure);

3. unscrew the lid by rotating

it in an anti-clockwise

Cleaning the detergent dispenser

drawer

To remove the drawer, press

direction (see figure);

lever (1) and pull the drawer

outwards (2) (see figure).

Wash it under running water;

this procedure should be

repeated frequently.

4. clean the inside thoroughly;

5. screw the lid back on;

6. reposition the panel, making sure the hooks are securely

in place before you push it onto the appliance.

Checking the water inlet hose

Caring for your appliance drum

Check the inlet hose at least once a year. If there are any

cracks, it should be replaced immediately: during the wash

cycles, water pressure is very strong and a cracked hose

could easily split open.

• Always leave the door ajar to prevent unpleasant odours

from forming.

Cleaning the pump

The washer dryer is fitted with a self-cleaning pump which

does not require any maintenance. Sometimes, small items

(such as coins or buttons) may fall into the protective pre-

chamber at the base of the pump.

! Make sure the wash cycle has finished and unplug the

appliance.

Download from Www.Somanuals.com. All Manuals Search And Download.

Trouble shooting

Your washer dryer could occasionally fail to work. Before contacting the Technical Assistance Centre (see “Assistance”),

make sure that the problem cannot be not solved easily using the following list.

Problem:

The machine does not switch on.

Possible causes / Solutions:

• The appliance is not plugged into the socket fully, or not enough to make contact.

• There is no power to the socket, or the fuse has blown in the mains plug.

The wash cycle does not start.

The machine does not dry.

• The door is not closed properly.

• The ON/OFF button has not been pressed.

• The START/PAUSE button has not been pressed.

• The water tap has not been turned on to allow water to flow into the machine.

• The ‘DELAY TIMER’ has been selected.

• The ‘CHILD LOCK’ is activated (see ‘The machine just ‘beeps’ when a

programme or option is selected’ below).

• Check the 2 sections above.

• The ‘DRY’ button has been pressed to exclude drying.

The clothes are too hot when the

drying cycle is finished.

• A cooling-down period is always added to the end of each drying cycle. If the

clothes appear too hot to handle leave the door open to allow to cool further

before removing from the machine.

The machine does not fill with

• The water inlet hose is kinked.

water or Indicator light for the first • The water inlet hose is not connected to the water supply.

wash cycle flashing rapidly.

• The water pressure is too low.

• The water tap has not been turned on to allow water to flow into the machine.

• There is no water supply to the house.

• The inlet valve filter is blocked.

• The START/PAUSE button has not been pressed.

The machine continuously fills with • The top of the drain hose is too low - It must be fitted at a height between 65

water and continually drains away

or Water left in the drum

or Stuck on wash.

and 100 cm from the floor (see “Installation”).

• The drain hose is connected incorrectly to the sink trap allowing water to run

into the machine, the drain hose must be positioned higher than the bottom of

the sink to prevent water flowing down the drain hose.

• The end of the drain hose has been pushed too far down the standpipe, the

‘U’ bracket should be fitted 100 mm from the end of the drain hose.

The machine does not drain or spin • The Pump filter is blocked.

- (error lights flashing).

• The drain hose is kinked (see “Installation”).

• New Installation - The blanking cap or spigot has not been removed if

connected under a sink.

• The drain hose or sink trap is blocked.

The programme takes too long.

• Programme times will vary due to water pressure, the incoming water

temperature and if the wash load goes out of balance. This will increase the

programme time accordingly (see ‘The machine wont spin properly’ below)

- (Most Common Cause!)

• The feet have not been adjusted, enabling the machine to rock.

• New Installation - Either the Transit Bolts including the plastic spacers, or the

Polystyrene Packaging have not been removed when installing the machine.

• The machine is trapped between cabinets and/or walls.

• The load is in a slight out of balance condition and machine is spinning, but at

a lower speed.

The machine vibrates a lot during

the spin cycle.

• There will always be some motor, pump and drum noise during spin.

The machine is noisy.

• Out of Balance detected when attempting to go into a spin cycle - If this

happens the machine will continue to try to repeat the distribution of the load

required before the machine will go into higher spin speeds - This will increase

the programme time accordingly. This is a safety feature to prevent damage.

Out of Balance can be caused by washing a single heavy item (eg duvet, quilt,

etc). - Try the programme again using a different load.

The machine wont spin properly.

Download from Www.Somanuals.com. All Manuals Search And Download.

The machine leaks from the

dispenser.

• The dispenser drawer is blocked with detergent and requires cleaning.

• The water pressure is too high and requires turning down - turn down the tap

on the water supply pipe slightly and try again.

• The machine is tilting forwards - It must be level when in its final position.

The machine leaks (other than

dispenser).

• The fill hose is loose, check both the cabinet and tap ends.

• The fill hose is tight but still leaks, if so replace the rubber washers, or the fill

hose is missing the rubber washer.

• The drain hose is not fixed in properly.

The Phase in Progress indicator

lights flash rapidly at the same

time as the ON/OFF indicator light.

• Switch off the machine and unplug it, wait for approximately 1 minute and then

switch back on again. If the problem persists contact Technical Assistance

Centre.

The machine smells.

• The machine requires a service wash. Run a 90 degree wash cycle with

detergent and no laundry.

The machine door cannot be

opened.

• The door will not open until the door lock indicator light goes out shortly after

the program has finished.

• If there is no power to the machine you need to perform the manual unlocking

procedure (see Precautions & Tips).

Door Seal damaged at the bottom.

• The door seal has drainage holes at the bottom - This is normal.

• The water level is correct if it can be seen at the bottom of the door.

The water level is too low when

the machine is washing.

The machine just ‘beeps’ when a

programme or option is selected

(Child Lock Symbol is lit).

• Deactivate the Child Lock feature by pressing and holding in the ‘CHILD

LOCK’ button for 2 seconds.

Clothes are coming out too wet on

‘Steam Refresh’ cycle.

• Only dry items are to be used for this program. The program refreshes

garments by removing bad odours and relaxing the fibres, also making items

easier to iron if required.

There is too much foam.

• The detergent is not suitable for machine washing (it should display the text

‘for washing machines’ or ‘hand and machine wash’ or the like).

• Too much detergent was used - less detergent is required in soft water.

After completing the programme,

or before starting a programme,

the machine has turned itself off

(no lights).

• To comply with new energy saving regulations the machine is fitted with an

automatic standby system. Press ‘ON/OFF’ button for 3 seconds to activate

the machine, it can then either be switched off or a new programme selected.

General.

• Your washing machine contains sensors that monitor progress during the wash

cycle (eg: Water Levels, Temperatures, Out of Balance loads, Wash time/progress).

Normally, if your machine successfully completes the cycle, there is unlikely to

be anything wrong!

Remember, you will be charged for a service call for problems caused by incorrect installation, as listed above.

Not emptying contents from pockets may cause pump or drain blockages, or may damage the machine.

Do not wash items which do not have a wash label, or wash items that are not intended as machine washable.

Download from Www.Somanuals.com. All Manuals Search And Download.

Assistance

Guarantee

12 Months Parts and Labour Guarantee

Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown

repairs for twelve months from the date of purchase.

This gives you the reassurance that if, within that time, your appliance is proven to be defective

because of either workmanship or materials, we will, at our discretion, either repair or replace the

appliance at no cost to you.

This guarantee is subject to the following conditions:

The appliance has been installed and operated correctly and in accordance with our

operating and maintenance instructions.

The appliance is used only on the electricity or gas supply printed on the rating plate.

The appliance has been used for normal domestic purposes only.

The appliance has not been altered, serviced, maintained, dismantled, or otherwise

interfered with by any person not authorised by us.

Any repair work must be undertaken by us or our appointed agent.

Any parts removed during repair work or any appliance that is replaced become our property.

The appliance is used in the United Kingdom or Republic of Ireland.

The guarantee does not cover:

Damage resulting from transportation, improper use, neglect or interference or as a result

of improper installation.

Replacement of any consumable item or accessory . These include but are not limited to: plugs,

cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.

Replacement of any removable parts made of glass or plastic.

THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL OR NON-

DOMESTIC PREMISES.

5 Year Parts Guarantee

Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you

registering your appliance with us and the parts being fitted by one of our authorised engineers. There

will be a charge for our engineer’s time. To activate the extra parts warranty on your appliance, simply

call our registration line on 08448 24 24 24 (ROI 01 230 0800).

Extended Guarantees

We offer a selection of repair protection plans that enable you to fully cover yourself against the expense

of repair bills for the life of your policy. To find the ideal plan for you please call our advice line on

08448 226 226 (Republic of Ireland 01 230 0233).

Free Helpdesk Service

We have a dedicated team who can provide free advice and assistance with your appliance if you

experience any technical difficulties within the first 90 days of ownership. Simply call our Hotpoint

Service Hotline on 08448 224 224 (Republic of Ireland 0818 313 413) for telephone assistance, or,

where necessary, to arrange for an engineer to call. If we cannot resolve the technical problem we will

replace your machine or, if you prefer, give you your money back.

Download from Www.Somanuals.com. All Manuals Search And Download.

After Sales Service

No one is better placed to care for your Hotpoint appliance during the course of its working life than

us - the manufacturer.

Essential Contact Information

Hotpoint Service

We are the largest service team in Europe offering you access to 400 skilled telephone advisors and

1000 fully qualified engineers on call to ensure you receive fast, reliable, local service.

UK: 08448 224 224

Republic of Ireland: 0818 313 413

www.hotpointservice.co.uk

Please note: Our advisors will require the following information:

Model number:

Serial number:

Parts and Accessories

We supply a full range of genuine replacement parts as well as accessory products that protect and

hygienically clean your appliance to keep it looking good and functioning efficiently throughout its life.

UK: 08448 225 225

Republic of Ireland: 0818 313 413

www.hotpointservice.co.uk

Appliance Registration

We want to give you additional benefits of Hotpoint ownership. To activate your free 5 year parts

guarantee you must register your appliance with us.

UK: 08448 24 24 24

Republic of Ireland: 01 230 0800

www.hotpointservice.co.uk

Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB

Indesit Company Unit 49 Airways Industrial Estate,Dublin 17

Recycling & Disposal Information

As part of Hotpoint’s continued commitment to helping the environment, Hotpoint reserves the right

to use quality, recycled components to keep down customer costs and minimise material wastage.

Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children,

remove the door, plug and cut the mains cable off flush with the appliance. Dispose of these parts

Download from Www.Somanuals.com. All Manuals Search And Download.

195076163.06

12/2010

Xerox Fabriano

Download from Www.Somanuals.com. All Manuals Search And Download.

Graco Inc Paint Sprayer 206 448 User Manual
Grizzly Drill H8071 User Manual
Haier Refrigerator 16 User Manual
Hotpoint Double Oven 6180 User Manual
HP Hewlett Packard Computer Hardware DL165 User Manual
HP Hewlett Packard Projector ep9010 User Manual
HP Hewlett Packard Server 686210 S01 User Manual
Husqvarna Snow Blower ST 224 User Manual
IBM Network Card 9000s User Manual
IBM Printer LA75P User Manual