LARDER FRIDGE - MODELS RLA34,RLA36,RLM34,RLM36
INSTRUCTIONS FOR INSTALLATION & USE
To ensure that your fridge runs reliably and efficiently follow these steps.
GETTING STARTED:
STEP 1
STEP 2
Choose a location for your
fridge, away from any
heat sources and
Move the fridge into
position, using the sides
of the cabinet. Take care
to avoid damaging the
refrigerant circuit pipe
work on the rear.
allow adequate
ventilation - 30mm
(11/4 inch) gap above.
STEP 3
STEP 4
Before plugging in and
switching on, leave the
fridge in its final
location for at least 15
minutes to allow it to
settle.
Level the fridge by
adjusting the front feet.
This will stop rocking or
vibration and keep the
door aligned.
STEP 5
STEP 6
Your fridge is now
working.
If after 24 hours your
fridge is not operating as
you want, refer to the
Troubleshooting section.
Plug in and switch on.
Allow the fridge to cool
before placing food
inside.
All food in the fridge
should be covered.
Read the rest of these instructions to get the best from your appliance
and remember to fill in your guarantee registration.
Download from Www.Somanuals.com. All Manuals Search And Download.
Keep this Book in a safe place for quick reference.
Installation
30mm (11/4 inch)
Location & Air Circulation
Locate your fridge away from sources of heat e.g.
cookers, radiators, direct sunlight as extreme temperature
will affect its performance.
1
Allow a minimum 30mm (1 /4 inch) between the top of
the fridge and the underside of the worktop.
Providing you follow the recommended ventilation requirements you will :-
G
G
G
G
Prolong the life of the fridge.
Minimise the risk of condensation on the outside of the fridge.
Minimise the running costs.
Minimise operating sounds caused by vibration.
Minimum space required to open door
The fridge needs a space of 600mm (24 inches) in front to allow the door to open.
1
4
When positioning the fridge next to a unit, a gap of 30mm (1 / inch) can be left
at the hinge side of the door to allow the easy removal of furniture. If preferred
the fridge can be positioned so that a gap is not left. This will restrict how far the
door can be opened but the furniture can still be removed (see diagram below).
The door hinge side can be changed to make it easier to open (see ‘Door Reversal’
in the CLEANING & MAINTENANCE section).
TOP VIEW
TOP VIEW
less than 30mm
30mm or more
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Levelling:
Level the fridge when it is in its final location by adjusting the front feet, until firm
contact is made with the floor. This will stop rocking or vibration and keep the door
aligned which helps the fridge run reliably and efficiently.
Before plugging in and switching on, leave the fridge standing in its final location for
at least 15 minutes to allow it to settle.
Fitting a Fridge under a Work Top
To minimise running costs Hotpoint recommend fitting a vent to the rear of your
worktop, which is available from Hotpoint Genuine Parts & Accessories Mail Order
Hotline (see KEY CONTACTS, back page).
WARNING: If there is less than 30mm clearance above the fridge, a vent must be
fitted to provide adequate ventilation above your fridge.
Bottle Retainer:
To fit the bottle rack retainer:
Locate the retainer groove at one end of
the bottle rack and then gradually press
down along the top edge until the
retainer is fully in the home position.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR 5 YEAR PARTS GUARANTEE ON 08448 24 24 24
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Electrical Supply
WARNING: This appliance must be earthed.
The fridge must be positioned so that the plug is accessible after
installation.
Fuses
Your appliance comes fitted with a plug and a 13A fuse. If you need to replace the
fuse, only use those rated at 13A and ASTA approved to BS1362.
Changing the Plug
Cut off and dispose of the supplied plug if it does not fit your socket.
WARNING: To avoid a shock hazard do not insert the discarded plug into a socket
anywhere else.
IMPORTANT WIRES IN THE MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE
FOLLOWING CODE :
Green/Yellow
Blue
-
-
Earth
Neutral
Brown
-
Live
If you change the plug, the colour of wires in the mains lead may not correspond with
the colour of the markings identifying terminals in the plug. You should therefore
wire it as shown above.
Changing the Mains Lead
This fridge is fitted with a special mains lead. If you need to replace the mains lead
due to damage, one can be bought from Hotpoint Service (see KEY CONTACTS, back
page). It is strongly advised that this work is carried out by a qualified electrician.
CE Marking certifies that this appliance conforms to the following EEC
directives : Low Voltage Equipment - 72/23/EEC & 93/68 EEC
Electromagnetic Compatibility 89/336/EEC, 92/31/EEC & 93/68/EEC
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR 5 YEAR PARTS GUARANTEE ON 08448 24 24 24
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls
Controlling the Temperature of the Fridge Compartment
The control wheel on the front of the worktop adjusts the internal fridge
compartment temperature. The internal temperature should be 5˚C or colder
although some sections, such as the salad bin, will be slightly warmer.
The setting of the control wheel will depend on the location of the fridge, the room
temperature and how often the door is opened. The normal set point (marked by a 3
and N on the dial) is usually suitable. If you need to adjust the temperature turn the
control wheel:
Clockwise (higher number) - Colder
Anti-clockwise (lower number) - Warmer
Temperature Indicator
(not applicable to all models)
The temperature indicator is located on the bottom right
hand side of the refrigerator wall.
This indicator shows when the refrigerator compartment of
your larder fridge is operating at the correct temperature.
After plugging in and switching on PLEASE WAIT 24 HOURS for the refrigerator
compartment temperature to stabilise. After this time the indicator should clearly
show OK and that indicates the refrigerator compartment is operating at the correct
temperature.
If the indicator is completely black, the compartment temperature is too high and
you should adjust the temperature wheel to a colder setting (see above).
If you have to adjust the temperature setting please WAIT A MINIMUM OF 10 HOURS,
this is time for the temperature to stabilise before checking that the indicator is
showing OK.
If large quantities of food have been added or if the refrigerator door has been
opened frequently it is normal for the temperature indicator not to show OK. WAIT A
MINIMUM OF 10 HOURS before adjusting the temperature setting to a colder
position.
You can check the temperature of the fridge compartment by using a Fridge Freezer
Thermometer available from Hotpoint Genuine Parts and Accessories Mail Order
Hotline (see KEY CONTACTS back page).
WARNING: Do not use a mercury filled thermometer, as breakage would cause a
health hazard.
Your fridge must NOT be placed in a room where the temperature goes below 6˚C or
above 38˚C for prolonged periods, as the internal fridge temperature will not be
maintained.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Useful Advice
A
B
C
A
B
D
B
Note:
The Rating Plate, which lists the appliance Model Number and Serial
Number can be found near the bottom of the left hand internal wall.
STORAGE ZONES
Zone Type
Food Storage
A
Cool
Dairy products, Cheese, butter, margarine,
Low fat spreads, cooking fats / lards
Preserves - Jam, curd, marmalade,
spread, salad dressing or sauces.
B
C
Colder
General food storage
Coldest
Meat fish & poultry
Pre-cooked / chilled food
D
Salad
Bin
Vegetables, fruit and salad items
(Not recommended for the storage of
bananas or onions).
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR 5 YEAR PARTS GUARANTEE ON 08448 24 24 24
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Useful Advice
Making the best use of your Fridge
Note : Always use the handle provided to open the fridge door.
To ensure that your fridge operates as efficiently as possible :
G
Follow food packaging “best before/use by” instructions or your suppliers
advice on a suitable maximum storage time.
G
Keep foods covered to retain moisture and prevent flavour/odour
transference. Plastic bags, aluminium foil, plastic stretch wrap and containers
with lids are ideal.
G
G
Avoid opening the doors unnecessarily or for longer than needed.
Allow hot or warm food to cool down in covered containers before placing in
fridge, as placing hot food inside reduces efficiency.
Storing Food in a Fridge
G
Pack and store cooked and fresh food separately.
G
Wrap raw or defrosting meat and poultry in polythene or foil and store
below cooked foods and dairy products to avoid contamination of dripping
food juices.
G
Wrap cheese in greaseproof paper and place in an airtight container or
polythene bag.
Bring to room temperature before consuming.
Empty left over canned food into a covered storage containers before
placing in the fridge.
Position food to allow cold air to circulate freely, ensuring nothing comes
into contact with the interior back wall of the fridge, or covers the defrost
gutter drain hole below this.
G
G
G
Use the different storage zones inside your fridge compartment to store a
wide variety of food items.
Microban® is a unique antibacterial technology which is built into interior
components of your fridge during manufacture. Microban® protects against growth
of potentially harmful and odour causing bacteria on the interior fridge surfaces,
thereby keeping your fridge fresher and more hygienically clean during use.
Microban® will not wash out or wear out and will provide continuous protection
against bacteria for the life of your fridge. Microban® technology has been proven
safe, durable and effective over many years of use in personal care and household
consumer products. In addition, Hotpoint operate a rigorous antibacterial testing
programme through approved independent testing laboratories.
Note : You should continue to clean your fridge as recommended (see CLEANING
& MAINTENANCE section). Microban® provides an extra level of hygiene
protection in your fridge in between cleanings.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR 5 YEAR PARTS GUARANTEE ON 08448 24 24 24
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Useful Advice
Advice on Adjusting Shelves
Make the most of the interior storage
space by repositioning shelves to suit the
various heights of individual items you
wish to store.
To remove, ensure that the door is open fully.
Slide the shelf forward and tilt from position.
Split glass shelf
The split shelf can be used as a standard shelf but also as
two half shelves.
The front half can be repositioned above or below to
enable storage of larger items.
Note : Only the front half of the
shelf can be repositioned, the back
half must remain in its original
position.
Salad Bins
For the storage of fruit, vegetables and salad items.
When storing vegetables, remove unusable leaves and soil and leave lettuce, cabbage
and cauliflower on the stem.
It is advisable to clean the salad bin regularly, it can be removed by sliding it out from
position.
Note : Care must be taken to ensure that the salad bin is closed before
shutting the fridge door.
Commodity and Bottle Racks
Commodity racks can be repositioned in the door to suit your storage requirements.
The lidded commodity rack is recommended for the storage of dairy items, such as
butter, margarine and cheese.
To remove, lift rack vertically to release from fixing supports.
To replace, align grooves on either side of the rack above fixing supports and push
down until secure.
In order to get the best results from the bottle retainer it is advised that it be
positioned centrally on the bottle rack.
Egg Rack
The egg rack can be used in conjunction with any commodity rack and is easily
removed for cleaning.
Note: Wipe, don’t wash eggs.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Defrosting and Cleaning
No manual defrosting required
The fridge compartment will defrost automatically. During defrost periods water
droplets form on the interior back wall of your Larder Fridge and refreeze afterwards.
Note : if your kitchen becomes exceptionally warm, your Larder Fridge may not
defrost regularly.
WARNING: Ensure the defrost drain hole is kept clear and that stored food does
not come into contact with the interior back wall of your Larder Fridge.
Cleaning
WARNING: Switch off electrical supply and pull out mains plug before cleaning.
Interior
1.
Remove food and wrap or cover to keep it cool.
2.
Remove salad bins, racks and shelves from the fridge compartment and wash
in warm water and washing up liquid using a soft cloth, dry thoroughly.
Note : It is important to ensure that cleaned shelves, baskets and bins are
thoroughly dried before refitting to the fridge compartment.
3.
Wipe interior and fitting with a clean cloth wrung out in a solution of either
one teaspoon of bicarbonate of soda to one pint of water or Milton™
sterilising fluid, diluted according to the manufacturer’s instructions.
Dry interior thoroughly with a clean cloth before replacing fittings and food.
4.
Exterior
Use a clean soft cloth wrung out in warm water and washing up liquid to wipe the
exterior surface, dry thoroughly.
WARNING: Do not use abrasive powder, household cleaner, bleach or wax polish
to clean your fridge, they leave a smell in the fridge and can damage the exterior.
Use a soft brush or vacuum cleaner to remove dust from underneath the fridge and
from the compressor and condenser situated at the back of the fridge.
WARNING: Do not damage the pipework.
Door Seal
Use warm water and a clean soft cloth to wipe along and in between the creases of
the door seal, dry thoroughly. Take care not to damage the seal and avoid using
sharp objects.
WARNING: Do not use detergent, it will damage the seal.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR 5 YEAR PARTS GUARANTEE ON 08448 24 24 24
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Defrosting and Cleaning
Going Away
If you are going away and don’t want to use your fridge, switch off the socket outlet
and pull out the mains plug. Remove food and follow the cleaning instructions on
the previous page.
Note : Leave the door ajar to prevent an accumulation of odours.
Changing the Light Bulb
WARNING: Switch off at socket outlet and pull out the mains plug
Obtain a replacement SES 15W bulb from the Hotpoint Genuine Parts and
Accessories Mail Order Hotline (see KEY CONTACTS back page) and fit as follows :
1.
Remove any shelves from directly below the interior light, to make access
easier.
2.
3.
4.
5.
Squeeze the side of the lamp guard lightly to unclip. Remove and retain.
Remove old bulb and fit new one.
Refit lamp guard.
Plug in and switch on electrical supply.
Defrosting the appliance
below.
! Follow the instructions
Do not speed up the defrosting process by using any
devices or tools, you may damage the refrigeration
circuit.
The refrigerator has an
automatic defrosting
function: water is ducted
to the back of the
appliance by a special
discharge outlet (see
diagram) where the heat
produced by the
compressor causes it to
evaporate. It is necessary
to clean the discharge
water can flow out easily.
hole regularly so that the
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR 5 YEAR PARTS GUARANTEE ON 08448 24 24 24
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
You will need a selection of small hand tools, screwdrivers, spanners etc. to carry out
this procedure.
Our Service Department can arrange for an Engineer to do the conversion for you but
a charge will be made.
Door Reversal
WARNING: Switch off electrical supply and pull out the mains plug.
Remove loose items/fittings from inside the fridge and place food into insulated
containers whilst carrying out this operation.
1.
2.
3.
4.
5.
Open the door as wide as possible.
Note : You may require assistance to do this:
Support the door and using a screwdriver, remove the screw
securing the top hinge.
Carefully tilt the door to remove the hinge from the cabinet
and lift the door off the bottom hinge.
Remove the spacing washers from the bottom hinge.
Note : You may require assistance to do this:
Using the packaging from the appliance or a suitable substitute to support
the back of the appliance. Lay the appliance on it’s back ensuring the
pipework at the back is not damaged or bent. Be careful that the appliance
does not run away from you when the wheels touch the floor.
Unscrew the foot plate and hinge bracket fitted to the bottom right hand
side of the appliance. Unscrew the foot and footplate fitted to the bottom
left hand side of the appliance.
Refit the hinge bracket and the footplate to the opposite sides of the
appliance. Screw in the feet until there is approximately 35mm projecting
from the bottom front edge of the appliance.
6.
7.
8.
Lift the appliance onto it’s feet. You may require assistance to do this:
Lift the appliance from the rear of the tabletop and stand it on it’s feet and
wheels. Be careful that the appliance does not run away from you when
the wheels touch the floor.
9.
Using a thin blunt instrument, remove the hinge
bush cap from the top left of the door and refit on
the top right.
10.
If applicable - using a screwdriver, remove the door
stop from the bottom right of the door and refit on
the bottom left.
door stop
Note : You may require assistance to do this:
11.
12.
Replace the top hinge onto the door, slide the door onto the bottom hinge
pin and support the door whilst screwing the top hinge into position. Ensure
that the top hinge bracket is positioned correctly.
Adjust the front feet (see ‘Levelling’ SAFETY & INSTALLATION section).
Note : Let the appliance stand upright in it’s final location for at least 15
minutes before plugging in and switching on the electricity supply.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
IS THE FRIDGE WORKING AS YOU
WANT?
The interior light doesn’t work
WARNING: Switch off the socket outlet
and pull out the mains plug.
1. Check bulb is screwed in correctly. If
still not working then see ‘Changing
the Light Bulb’ in the CLEANING &
MAINTENANCE section.
Have you read through the instruction
book ?
If you still have a problem, before calling
our service organisation see if any of the
tips below help.
Ice builds up rapidly inside the fridge
1. Check that nothing is stopping the
door from closing properly.
2. Check that foods and liquids are
covered to avoid the build up of
moisture inside.
The appliance will not work
1. Check plug is firmly positioned in the
socket outlet and the power supply is
switched on.
2. Check power supply with another
appliance.
3. See ‘Defrosting’ in the CLEANING &
MAINTENANCE section for advice.
3. Check fuse/circuit breaker.
4. Check the door is closed properly.
The appliance is making a lot of noise
1. Check that the rear pipe work is clear
of the wall, skirting board and other
obstacles.
If there is still a problem contact
Hotpoint Service (See
,
back page, for
contact details).
2. Check that all feet/wheels are firmly
in contact with the floor and the
fridge is level.
OPERATING SOUNDS OF A FRIDGE
These are the normal types of sound that
3. See OPERATING SOUNDS below.
your fridge will make:
The temperature is too warm
1. Turn the control wheel to a higher
number. See CONTROLS section.
2. If the appliance is close to a heat
source, move it to another location.
3. Check that there is enough
ventilation around the appliance.
4. Check that the door has been closed
properly.
The fridge motor (compressor) makes a
buzzing or humming sound when it is
running. This can be louder when it is
first switched on. This sound will reduce
over the first few months.
Gases flowing through the pipes can
produce gurgling, bubbling, roaring or
humming noises.
The temperature is too cold
1. Turn the control wheel to a lower
number. See CONTROLS section.
The temperature control can make a
clicking noise when it turns the motor on
and off.
There is water beneath the salad bin
and on the floor
1. Check defrost gutter drain hole is not
Expansion and contraction of parts
inside the fridge can produce a cracking
noise as they rapidly change
temperature.
covered.
2. Check that nothing has come into
contact with the interior back wall of
the fridge.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Guarantee
12 Months Parts and Labour Guarantee
Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown
repairs for twelve months from the date of purchase.
This gives you the reassurance that if, within that time, your appliance is proven to be defective because
of either workmanship or materials, we will, at our discretion, either repair or replace the appliance at no
cost to you.
This guarantee is subject to the following conditions:
-
The appliance has been installed and operated correctly and in accordance with our
operating and maintenance instructions.
-
-
-
The appliance is used only on the electricity or gas supply printed on the rating plate.
The appliance has been used for normal domestic purposes only.
The appliance has not been altered, serviced, maintained, dismantled, or otherwise
interfered with by any person not authorised by us.
-
-
-
Any repair work must be undertaken by us or our appointed agent.
Any parts removed during repair work or any appliance that is replaced become our property.
The appliance is used in the United Kingdom or Republic of Ireland.
The guarantee does not cover:
-
-
-
Damage resulting from transportation, improper use, neglect or interference or as a result of
improper installation.
Replacement of any consumable item or accessory . These include but are not limited to: plugs,
cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.
Replacement of any removable parts made of glass or plastic.
THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL
OR NON-DOMESTIC PREMISES.
5 Year Parts Guarantee
Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you
registering your appliance with us and the parts being fitted by one of our authorised engineers. There
will be a charge for our engineer's time. To activate the extra parts warranty on your appliance, simply
call our registration line on 08448 24 24 24 (ROI 01 230 0233).
Extended Guarantees
We offer a selection of repair protection plans that enable you to fully cover yourself against the expense
of repair bills for the life of your policy. To find the ideal plan for you please call our advice line on 0 8448
226 226 (ROI 01 230 0233).
Helpdesk Service
We have a dedicated team who can provide free advice and assistance with your appliance if you
experience any technical difficulties within the first 90 days of ownership. Simply call our Hotpoint
Service Hotline on 08448 224 224 (ROI 01 230 0233) for telephone assistance, or, where necessary, to
arrange for an engineer to call. If we cannot resolve the technical problem we will replace your machine
or, if you prefer, give you your money back.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR 5 YEAR PARTS GUARANTEE ON 08448 24 24 24
14
Download from Www.Somanuals.com. All Manuals Search And Download.
After Sales Service
No one is better placed to care for your Hotpoint appliance during the course of its working life than us -
the manufacturer.
Essential Contact Information
Hotpoint Service
We are the largest service team in Europe offering you access to 400 skilled telephone advisors and
1000 fully qualified engineers on call to ensure you receive fast, reliable, local service.
UK: 08448 24 24 24
Republic of Ireland: 0818 313 413
Please note: Our advisors will require the following information:
Model number:
Serial number:
Parts and Accessories
We supply a full range of genuine replacement parts as well as accessory products that protect and
hygienically clean your appliance to keep it looking good and functioning efficiently throughout its life.
UK: 08448 225 225
Republic of Ireland: 0818 313 413
Appliance Registration
We want to give you additional benefits of Hotpoint ownership. To activate your free 5 year parts guarantee
you must register your appliance with us.
UK: 08448 24 24 24
Republic of Ireland: 01 230 0800
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB
Indesit Company Unit 49 Airways Industrial Estate,Dublin 17
Recycling & Disposal Information
As part of Hotpoint's continued commitment to helping the environment, Hotpoint reserves the right to use
quality, recycled components to keep down customer costs and minimise material wastage.
Please dispose of packaging and old appliances carefully. Please see section “Precautions and tips” for
details about disposal legislation. To minimise the risk of injury to children, remove the door, plug and cut
the mains cable off flush with the appliance. Dispose of these parts separately to ensure that the appliance
can no longer be plugged into a mains socket, and the door cannot be locked shut.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR 5 YEAR PARTS GUARANTEE ON 08448 24 24 24
15
Download from Www.Somanuals.com. All Manuals Search And Download.
195051328.02
10/2012
Download from Www.Somanuals.com. All Manuals Search And Download.
|