Hoshizaki America, Inc.
Hoshizaki
Modular Flaker
Models
F-801MAH(-C)
F-801MWH(-C)
SERVICE MANUAL
“A Superior Degree
of Reliability”
Number: 73113
Issued: 7-29-2004
Revised: 6-15-2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Please review this manual. It should be read carefully before the icemaker is serviced or
maintenance operations are performed. Only qualified service technicians should service
and maintain the icemaker. This manual should be made available to the technician prior
to service or maintenance.
CONTENTS
I. Specification ...................................................................................................................... 5
1. Icemaker ....................................................................................................................... 5
F-801MAH.................................................................................................................. 5
F-801MWH................................................................................................................. 6
F-801MAH-C.............................................................................................................. 7
F-801MWH-C ............................................................................................................. 8
II. General Information .......................................................................................................... 9
1. Construction ................................................................................................................. 9
F-801MAH/-C ............................................................................................................. 9
F-801MWH/-C .......................................................................................................... 10
2. Control Box Layout ..................................................................................................... 11
F-801MAH/-C ........................................................................................................... 11
F-801MWH/-C .......................................................................................................... 12
III.Technical Information ..................................................................................................... 13
1. Water Circuit and Refrigeration Circuit........................................................................ 13
F-801MAH/-C ........................................................................................................... 13
F-801MWH/-C .......................................................................................................... 14
2. Wiring Diagrams ......................................................................................................... 15
F-801MAH/-C, F-801MWH/-C .................................................................................. 15
3. Sequence of Electrical Circuit .................................................................................... 16
4. Timing Chart............................................................................................................... 26
5. Performance Data....................................................................................................... 29
F-801MAH................................................................................................................ 29
F-801MWH............................................................................................................... 30
F-801MAH-C............................................................................................................ 31
F-801MWH-C ........................................................................................................... 32
IV. Adjustment of Components............................................................................................ 33
1. Adjustment of Water Regulating Valve (water-cooled model only).............................. 33
2. Adjustment of Flake Size............................................................................................ 34
V. Service Diagnosis........................................................................................................... 35
1. No Ice Production ....................................................................................................... 35
2. Low Ice Production ..................................................................................................... 37
3. Other........................................................................................................................... 38
VI. Removal and Replacement of Components.................................................................. 39
1. Service for Refrigerant Lines ...................................................................................... 39
[a] Refrigerant Recovery........................................................................................... 39
[b] Evacuation and Recharge [R-404A] .................................................................... 39
2. Brazing ....................................................................................................................... 40
3. Removal and Replacement of Compressor................................................................ 41
4. Removal and Replacement of Drier ........................................................................... 42
3
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Removal and Replacement of Expansion Valve......................................................... 43
6. Removal and Replacement of Water Regulating Valve (water-cooled model only) .... 44
7. Removal and Replacement of Evaporator Assembly ................................................. 45
8. Removal and Replacement of Fan Motor ................................................................... 49
9. Removal and Replacement of Control Water Valve .................................................... 49
10. Removal and Replacement of Flush Water Valve..................................................... 50
VII. Cleaning and Maintenance .......................................................................................... 51
1. Preparing the Icemaker for Long Storage ................................................................... 51
2. Cleaning and Sanitizing Instructions .......................................................................... 52
[a] Cleaning Solution................................................................................................ 52
[b] Cleaning Procedure ............................................................................................ 53
[c] Sanitizing Solution............................................................................................... 54
[d] Sanitizing Procedure - Initial................................................................................ 54
[e] Sanitizing Procedure - Final ................................................................................ 55
3. Maintenance............................................................................................................... 57
4
Download from Www.Somanuals.com. All Manuals Search And Download.
I. Specification
1. Icemaker
F-801MAH
AC SUPPLY VOLTAGE
COMPRESSOR
GEAR MOTOR
FAN MOTOR
OTHER
MAXIMUM FUSE SIZE
MAX. HACR BREAKER (USA ONLY)
MAX. CIRC. BREAKER (CANADA ONLY)
MINIMUM CIRCUIT AMPACITY
APPROXIMATE ICE PRODUCTION
PER 24 HR.
115/60/1
120 V
120 V
115 V
120 V
20 A
20 A
20 A
20 A
9.4 RLA
3 FLA
0.85 FLA
0.03 A
51 LRA
1/4 HP
1/15 HP
Ambient
Temp.(°F)
70
WATER TEMP. (°F)
70
50
90
lbs./day ( kg/day )
Reference without *marks
* 823 (373) 786 (357) 748 (339)
711 (323) 677 (307) 644 (292)
613 (278) * 599 (272) 555 (252)
528 (239) 502 (228) * 471 (214)
80
90
100
SHAPE OF ICE
Flake
ICE QUALITY
Approx. 70%, Ice (90/70°F, Conductivity 200 µs/cm)
N/A
APPROXIMATE STORAGE CAPACITY
ELECTRIC & WATER CONSUMPTION
ELECTRIC W (kWH/100 lbs.)
POTABLE WATER
90/70°F
1131 (4.5)
72 (12)
70/50°F
1089 (3.2)
99 (12)
gal./24HR (gal./100 lbs.)
EXTERIOR DIMENSIONS (WxDxH)
EXTERIOR FINISH
22" x 27-3/8" x 25-15/16" (560 x 695 x 658mm)
Stainless Steel, Galvanized Steel (Rear)
Net 176 lbs. ( 80 kg ), Shipping 207 lbs. ( 94 kg )
Permanent - Connection
WEIGHT
CONNECTIONS - ELECTRIC
- WATER SUPPLY
Inlet 1/2" FPT
- DRAIN
Outlet 3/4" FPT
ICE MAKING SYSTEM
HARVESTING SYSTEM
ICE MAKING WATER CONTROL
COOLING WATER CONTROL
BIN CONTROL SYSTEM
COMPRESSOR
Auger type
Direct Driven Auger ( 1/4HP Gear Motor )
Float Switch
N/A
Mechanical Bin Control ( Proximity Sw. )
Hermetic,
Model RS43-C2E-CAA
CONDENSER
EVAPORATOR
Air-cooled, Fin and Tube Type
Copper Tube on Cylinder
REFRIGERANT CONTROL
REFRIGERANT CHARGE
DESIGN PRESSURE
PC BOARD CIRCUIT PROTECTION
COMPRESSOR PROTECTION
GEAR MOTOR PROTECTION
REFRIGERANT CIRCUIT PROTECTION
LOW WATER PROTECTION
ACCESSORIES - SUPPLIED
- REQUIRED
Thermostatic Expansion Valve
R-404A,
1lb 12oz
(800 g)
High 427 PSIG, Low 230 PSIG
High Voltage Cut-off Relay
Auto-reset Overload Protector
Fuse (3A)
Auto-reset High Pressure Control Switch
Float Switch and Timer
Spare Fuse
Ice Storage Bin
OPERATING CONDITIONS
VOLTAGE RANGE
AMBIENT TEMP.
WATER SUPPLY TEMP.
WATER SUPPLY PRESSURE
104 - 127 V
45 - 100° F
45 - 90° F
10 - 113 PSIG
We reserve the right to make changes in specifications and design without prior notice.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
F-801MWH
AC SUPPLY VOLTAGE
COMPRESSOR
GEAR MOTOR
115/60/1
120 V
120 V
120 V
20 A
20 A
20 A
20 A
8.5 RLA
3 FLA
0.03 A
51 LRA
1/4 HP
OTHER
MAXIMUM FUSE SIZE
MAX. HACR BREAKER (USA ONLY)
MAX. CIRC. BREAKER (CANADA ONLY)
MINIMUM CIRCUIT AMPACITY
APPROXIMATE ICE PRODUCTION
PER 24 HR.
Ambient
Temp.(°F)
70
WATER TEMP. (°F)
70
50
90
lbs./day ( kg/day )
Reference without *marks
* 720 (327) 693 (315) 677 (307)
661 (300) 646 (293) 630 (286)
616 (279) * 605 (274) 587 (266)
573 (260) 560 (254) * 520 (236)
80
90
100
SHAPE OF ICE
Flake
ICE QUALITY
Approx. 70%, Ice (90/70°F, Conductivity 200 µs/cm)
N/A
APPROXIMATE STORAGE CAPACITY
ELECTRIC & WATER CONSUMPTION
ELECTRIC W (kWH/100 lbs.)
POTABLE WATER
90/70°F
1078 (4.3)
72 (12)
70/50°F
1076 (3.6)
86 (12)
WATER-COOLED CONDENSER
gal./24HR (gal./100 lbs.)
EXTERIOR DIMENSIONS (WxDxH)
EXTERIOR FINISH
360 (60)
219 (31)
22" x 27-3/8" x 25-15/16" (560 x 695 x 658mm)
Stainless Steel, Galvanized Steel (Rear)
Net 176 lbs. ( 80 kg ), Shipping 207 lbs. ( 94 kg )
Permanent - Connection
Inlet 1/2" FPT
Outlet 3/4" FPT
Auger type
Direct Driven Auger ( 1/4HP Gear Motor )
Float Switch
N/A
WEIGHT
CONNECTIONS - ELECTRIC
- WATER SUPPLY
Cond. Inlet 1/2" FPT
Cond. Outlet 3/8" FPT
- DRAIN
ICE MAKING SYSTEM
HARVESTING SYSTEM
ICE MAKING WATER CONTROL
COOLING WATER CONTROL
BIN CONTROL SYSTEM
COMPRESSOR
Mechanical Bin Control ( Proximity Sw. )
Hermetic,
Model RS43-C2E-CAA
CONDENSER
EVAPORATOR
Water-cooled, tube in tube type
Copper Tube on Cylinder
REFRIGERANT CONTROL
REFRIGERANT CHARGE
DESIGN PRESSURE
PC BOARD CIRCUIT PROTECTION
COMPRESSOR PROTECTION
GEAR MOTOR PROTECTION
REFRIGERANT CIRCUIT PROTECTION
LOW WATER PROTECTION
ACCESSORIES - SUPPLIED
- REQUIRED
Thermostatic Expansion Valve
R-404A,
1lb 1oz
(470 g)
High 427 PSIG, Low 230 PSIG
High Voltage Cut-off Relay
Auto-reset Overload Protector
Fuse (3A)
Auto-reset High Pressure Control Switch
Float Switch and Timer
Spare Fuse
Ice Storage Bin
OPERATING CONDITIONS
VOLTAGE RANGE
AMBIENT TEMP.
WATER SUPPLY TEMP.
WATER SUPPLY PRESSURE
104 - 127 V
45 - 100° F
45 - 90° F
10 - 113 PSIG
We reserve the right to make changes in specifications and design without prior notice.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
F-801MAH-C
AC SUPPLY VOLTAGE
COMPRESSOR
GEAR MOTOR
FAN MOTOR
OTHER
MAXIMUM FUSE SIZE
MAX. HACR BREAKER (USA ONLY)
MAX. CIRC. BREAKER (CANADA ONLY)
MINIMUM CIRCUIT AMPACITY
APPROXIMATE ICE PRODUCTION
PER 24 HR.
115/60/1
120 V
120 V
115 V
120 V
20 A
20 A
20 A
20 A
9.4 RLA
3 FLA
0.85 FLA
0.03 A
51 LRA
1/4 HP
1/15 HP
Ambient
Temp.(°F)
70
WATER TEMP. (°F)
70
50
90
lbs./day ( kg/day )
Reference without *marks
* 752 (341) 728 (330) 688 (312)
650 (295) 614 (279) 580 (263)
548 (249) * 552 (250) 490 (222)
463 (210) 437 (198) * 405 (184)
80
90
100
SHAPE OF ICE
Cubelet
ICE QUALITY
Approx. 80%, Ice (90/70°F, Conductivity 200 µs/cm)
N/A
APPROXIMATE STORAGE CAPACITY
ELECTRIC & WATER CONSUMPTION
ELECTRIC W (kWH/100 lbs.)
POTABLE WATER
90/70°F
1169 (5.1)
66 (12)
70/50°F
1110 (3.5)
90 (12)
gal./24HR (gal./100 lbs.)
EXTERIOR DIMENSIONS (WxDxH)
EXTERIOR FINISH
22" x 27-3/8" x 25-15/16" (560 x 695 x 658mm)
Stainless Steel, Galvanized Steel (Rear)
Net 176 lbs. ( 80 kg ), Shipping 207 lbs. ( 94 kg )
Permanent - Connection
WEIGHT
CONNECTIONS - ELECTRIC
- WATER SUPPLY
Inlet 1/2" FPT
- DRAIN
Outlet 3/4" FPT
ICE MAKING SYSTEM
HARVESTING SYSTEM
ICE MAKING WATER CONTROL
COOLING WATER CONTROL
BIN CONTROL SYSTEM
COMPRESSOR
Auger type
Direct Driven Auger ( 1/4HP Gear Motor )
Float Switch
N/A
Mechanical Bin Control ( Proximity Sw. )
Hermetic,
Model RS43-C2E-CAA
CONDENSER
EVAPORATOR
Air-cooled, Fin and Tube Type
Copper Tube on Cylinder
REFRIGERANT CONTROL
REFRIGERANT CHARGE
DESIGN PRESSURE
PC BOARD CIRCUIT PROTECTION
COMPRESSOR PROTECTION
GEAR MOTOR PROTECTION
REFRIGERANT CIRCUIT PROTECTION
LOW WATER PROTECTION
ACCESSORIES - SUPPLIED
- REQUIRED
Thermostatic Expansion Valve
R-404A,
1lb 12oz
(800 g)
High 427 PSIG, Low 230 PSIG
High Voltage Cut-off Relay
Auto-reset Overload Protector
Fuse (3A)
Auto-reset High Pressure Control Switch
Float Switch and Timer
Spare Fuse
Ice Storage Bin
OPERATING CONDITIONS
VOLTAGE RANGE
AMBIENT TEMP.
WATER SUPPLY TEMP.
WATER SUPPLY PRESSURE
104 - 127 V
45 - 100° F
45 - 90° F
10 - 113 PSIG
We reserve the right to make changes in specifications and design without prior notice.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
F-801MWH-C
AC SUPPLY VOLTAGE
COMPRESSOR
GEAR MOTOR
115/60/1
120 V
120 V
120 V
20 A
20 A
20 A
20 A
8.5 RLA
3 FLA
0.03 A
51 LRA
1/4 HP
OTHER
MAXIMUM FUSE SIZE
MAX. HACR BREAKER (USA ONLY)
MAX. CIRC. BREAKER (CANADA ONLY)
MINIMUM CIRCUIT AMPACITY
APPROXIMATE ICE PRODUCTION
PER 24 HR.
Ambient
Temp.(°F)
70
WATER TEMP. (°F)
70
50
90
lbs./day ( kg/day )
Reference without *marks
* 645 (293) 620 (281) 608 (276)
596 (270) 585 (265) 574 (260)
563 (255) * 550 (249) 541 (246)
531 (241) 521 (236) * 485 (220)
80
90
100
SHAPE OF ICE
Cubelet
ICE QUALITY
Approx. 80%, Ice (90/70°F, Conductivity 200 µs/cm)
N/A
APPROXIMATE STORAGE CAPACITY
ELECTRIC & WATER CONSUMPTION
ELECTRIC W (kWH/100 lbs.)
POTABLE WATER
90/70°F
1075 (4.7)
66 (12)
70/50°F
1083 (4.1)
77 (12)
WATER-COOLED CONDENSER
gal./24HR (gal./100 lbs.)
EXTERIOR DIMENSIONS (WxDxH)
EXTERIOR FINISH
302 (55)
199 (31)
22" x 27-3/8" x 25-15/16" (560 x 695 x 658mm)
Stainless Steel, Galvanized Steel (Rear)
Net 176 lbs. ( 80 kg ), Shipping 207 lbs. ( 94 kg )
Permanent - Connection
Inlet 1/2" FPT
Outlet 3/4" FPT
Auger type
Direct Driven Auger ( 1/4HP Gear Motor )
Float Switch
N/A
WEIGHT
CONNECTIONS - ELECTRIC
- WATER SUPPLY
Cond. Inlet 1/2" FPT
Cond. Outlet 3/8" FPT
- DRAIN
ICE MAKING SYSTEM
HARVESTING SYSTEM
ICE MAKING WATER CONTROL
COOLING WATER CONTROL
BIN CONTROL SYSTEM
COMPRESSOR
Mechanical Bin Control ( Proximity Sw. )
Hermetic,
Model RS43-C2E-CAA
CONDENSER
EVAPORATOR
Water-cooled, tube in tube type
Copper Tube on Cylinder
REFRIGERANT CONTROL
REFRIGERANT CHARGE
DESIGN PRESSURE
PC BOARD CIRCUIT PROTECTION
COMPRESSOR PROTECTION
GEAR MOTOR PROTECTION
REFRIGERANT CIRCUIT PROTECTION
LOW WATER PROTECTION
ACCESSORIES - SUPPLIED
- REQUIRED
Thermostatic Expansion Valve
R-404A,
1lb 1oz
(470 g)
High 427 PSIG, Low 230 PSIG
High Voltage Cut-off Relay
Auto-reset Overload Protector
Fuse (3A)
Auto-reset High Pressure Control Switch
Float Switch and Timer
Spare Fuse
Ice Storage Bin
OPERATING CONDITIONS
VOLTAGE RANGE
AMBIENT TEMP.
WATER SUPPLY TEMP.
WATER SUPPLY PRESSURE
104 - 127 V
45 - 100° F
45 - 90° F
10 - 113 PSIG
We reserve the right to make changes in specifications and design without prior notice.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
II. General Information
1. Construction
F-801MAH/-C
Water Supply
Inlet
Control Water Valve
Bin Control
Junction Box
Condenser
Fan Motor
Compressor
Drier
Ice Chute
Evaporator
Expansion
Valve
Flush Water
Valve
Control Box
Gear Motor
9
Download from Www.Somanuals.com. All Manuals Search And Download.
F-801MWH/-C
Water Supply
Inlet
Control Water Valve
Bin Control
Junction Box
Ice Chute
Water
Evaporator
Regulator
Expansion
Valve
Compressor
Drier
Flush Water
Valve
Control Box
Gear Motor
10
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Control Box Layout
F-801MAH/-C
WATER CONTROL
RELAY
FLUSH
TIMER
TRANSFORMER
GEAR
MOTOR
RELAY
FLUSH
CONNECTOR
CIRCUIT PROTECT
RELAY
FLUSH
SWITCH
GEAR
MOTOR
CAP.
ICE
FAN
MOTOR
CAP
PRESSURE
SWITCH
POWER
SWITCH
GEAR MOTOR
PROTECT RELAY
STARTER
FUSE
START
CAPACITOR
FUSE
(GEAR MOTOR)
RUN
CAPACITOR
CONTROL
TIMER
Note: The above component names are identical with the wiring label, but not with
the parts list.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
F-801MWH/-C
WATER CONTROL
RELAY
FLUSH
TIMER
TRANSFORMER
GEAR
MOTOR
RELAY
FLUSH
CONNECTOR
CIRCUIT PROTECT
RELAY
FLUSH
SWITCH
GEAR
MOTOR
CAP.
ICE
PRESSURE
SWITCH
POWER
SWITCH
GEAR MOTOR
PROTECT RELAY
STARTER
FUSE
START
CAPACITOR
FUSE
(GEAR MOTOR)
RUN
CAPACITOR
CONTROL
TIMER
12
Download from Www.Somanuals.com. All Manuals Search And Download.
III. Technical Information
1. Water Circuit and Refrigeration Circuit
F-801MAH/-C
13
Download from Www.Somanuals.com. All Manuals Search And Download.
F-801MWH/-C
14
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Wiring Diagrams
F-801MAH/-C, F-801MWH/-C
15
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Sequence of Electrical Circuit
[a] When power switch is moved to “ON” position and flush switch to “ICE” position,
water starts to be supplied to reservoir.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
[b] When reservoir has been filled, gear motor starts immediately.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
[c] Compressor starts about 60 sec. after gear motor starts.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
[d] Bin control operates, and about 6 sec. later, compressor and gear motor stop
simultaneously.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
[e] Low water (except water-cooled model).
20
Download from Www.Somanuals.com. All Manuals Search And Download.
[f] Low water (water-cooled model), or dirty air filter (air-cooled model), pressure
switch to “OPEN”, compressor and gear motor operate intermittently.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
[g] When flush switch is moved to “FLUSH” position, flush water valve opens and
flushes reservoir and evaporator.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
[h] When flush timer operates (for 15 min. every 12 hours).
23
Download from Www.Somanuals.com. All Manuals Search And Download.
[i] When 208-230V are supplied to circuit protect relay, it protects the circuit from
miswiring. If the power supply is properly connected, the contact of circuit protect
relay does not move even when the coil is energized.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
[j] When input voltage is too low, (less than 70%), gear motor fuse (1.5A) is blown
causing the compressor and gear motor to turn off immediately.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Miswiring. Circuit Protect Relay operates.)
Proper wiring. The unit starts.
4. Timing Chart
BIN CONTROL
OFF ON
1. CIRCUIT PROTECT
RELAY
ON
OFF
UPPER
LOWER
BOTTOM
2. WATER LEVEL
ON
UPPER
OFF
3. FLOAT
SWITCH
ON
LOWER
OFF
ON
4. WATER CONTROL
RELAY
OFF
5. CONTROL WATER
VALVE
ON
OFF
1 - 2
2 - 3
6. FLUSH TIMER
FLUSH
ICE
7. FLUSH SWITCH
8. FLUSH WATER
VALVE
ON
OFF
9. BIN CONTROL
ON
OFF
1 sec
6 sec
1 sec
10. GEAR MOTOR
RELAY
ON
OFF
ON
11. GEAR MOTOR
12. FAN MOTOR
13. COMPRESSOR
OFF
ON
OFF
60 sec
60 sec
ON
OFF
14. PRESSURE
SWITCH
ON
OFF
26
Download from Www.Somanuals.com. All Manuals Search And Download.
LOW WATER
FLUSH TIMER
27
Download from Www.Somanuals.com. All Manuals Search And Download.
FLUSH SWITCH
PRESSURE SWITCH
OFF ON
FLUSH
ICE
1. CIRCUIT PROTECT
RELAY
ON
OFF
UPPER
2. WATER LEVEL
LOWER
BOTTOM
ON
UPPER
3. FLOAT
OFF
SWITCH
ON
LOWER
OFF
ON
4. WATER CONTROL
RELAY
OFF
ON
5. CONTROL WATER
VALVE
OFF
1 - 2
2 - 3
6. FLUSH TIMER
FLUSH
ICE
7. FLUSH SWITCH
ON
8. FLUSH WATER
VALVE
OFF
ON
9. BIN CONTROL
OFF
150 sec
1 sec
1 sec
10. GEAR MOTOR
RELAY
ON
OFF
ON
11. GEAR MOTOR
OFF
ON
12. FAN MOTOR
OFF
60 sec
90 sec
60 sec
ON
13. COMPRESSOR
OFF
ON
14. PRESSURE
SWITCH
OFF
28
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Performance Data
F-801MAH
APPROXIMATE
ICE PRODUCTION
PER 24 HR.
Ambient
Temp. (F)
70
Water Temp. (F)
70
50
90
*
823 (373)
711 (323)
786 (357)
677 (307)
613 (278) * 599 (272)
528 (239) 502 (228) * 471 (214)
748 (339)
644 (292)
555 (252)
80
90
100
70
80
90
100
70
80
90
100
70
80
90
100
70
lbs./day ( kg/day)
APPROXIMATE ELECTRIC
CONSUMPTION
* 1089
1107
--
--
--
1095
1113
* 1131
1181
94
--
--
--
1101
1119
1147
* 1197
90
--
--
--
--
1125
1164
watts
--
--
APPROXIMATE WATER
CONSUMPTION PER 24 HR.
(TOTAL)
gal. / day (l/day)
EVAPORATOR OUTLET TEMP.
°F (°C)
*
*
*
99
85
74
63
15
16
17
19
(374)
(323)
(357)
(308)
(272)
(340)
(293)
(252)
(214)
(-9)
(-8)
(-8)
(-7)
81
77
67
(278) * 72
(240)
(-10)
(-9)
(-8)
(-7)
60
16
16
17
19
(228) * 57
(-9)
(-9)
(-8)
(-7)
16
17
18
20
*
*
HEAD PRESSURE
204 (14.3)
204 (14.3)
266 (18.7)
266 (18.7)
302 (21.2)
302 (21.2)
302 (21.2)
80
90
204 (14.3) * 266 (18.7)
204 (14.3)
PSIG (kg/cm2G)
100
70
266 (18.7) * 302 (21.2)
SUCTION PRESSURE
PSIG (kg/cm2G)
*
38
(2.7)
42
(3.0)
46
(3.3)
80
90
100
38
38
38
(2.7)
(2.7)
(2.7)
42
42
42
(3.0)
(3.0)
(3.0)
46
46
46
(3.3)
(3.3)
(3.3)
*
*
TOTAL HEAT OF REJECTION
6398 BTU/h (AT 90°F / WT 70°F)
Note: The data without *marks should be used for reference.
We reserve the right to make changes in specifications and design without prior notice.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
F-801MWH
APPROXIMATE
ICE PRODUCTION
PER 24 HR.
Ambient
Temp. (F)
70
Water Temp. (F)
70
50
90
*
720 (327)
661 (300)
693 (315)
646 (293)
616 (279) * 605 (274)
573 (260) 560 (254) * 520 (236)
677 (307)
630 (286)
587 (266)
80
90
100
70
80
90
100
70
80
90
100
70
80
90
100
70
lbs./day ( kg/day)
APPROXIMATE ELECTRIC
CONSUMPTION
* 1076
1076
--
--
--
--
1076
1077
* 1078
1071
--
--
--
--
1076
1077
1076
--
--
--
--
1077
1074
watts
* 1069
APPROXIMATE WATER
CONSUMPTION PER 24 HR.
(TOTAL)
gal. / day (l/day)
EVAPORATOR OUTLET TEMP.
°F (°C)
*
*
*
306 (1158)
318 (1205)
397 (1504)
415 (1571)
331 (1251) * 433 (1638)
344 (1304) 457 (1728) * 778 (2944)
631 (2387)
666 (2520)
704 (2666)
17
19
20
20
(-8)
(-7)
(-7)
(-7)
17
19
20
20
(-8)
(-7)
(-7)
(-7)
18
20
20
21
(-8)
(-7)
(-7)
(-6)
*
*
HEAD PRESSURE
265 (18.6)
265 (18.6)
265 (18.6)
265 (18.6)
266 (18.7)
266 (18.7)
266 (18.7)
80
90
265 (18.6) * 265 (18.6)
265 (18.6)
PSIG (kg/cm2G)
100
70
265 (18.6) * 266 (18.7)
SUCTION PRESSURE
PSIG (kg/cm2G)
*
42
(3.0)
43
(3.0)
44
(3.1)
80
90
100
42
42
42
(3.0)
(3.0)
(3.0)
43
43
43
(3.0)
(3.0)
(3.0)
44
44
44
(3.1)
(3.1)
(3.1)
*
*
WATER FLOW FOR CONDENSER
15 gal/h (AT 90°F / WT 70°F)
PRESSURE DROP OF COOLING WATER LINE Less than 7 PSIG
HEAT OF REJECTION FROM CONDENSER
HEAT OF REJECTION FROM COMPRESSOR
5155 BTU/h (AT 90°F / WT 70°F)
1050 BTU/h (AT 90°F / WT 70°F)
Note: The data without *marks should be used for reference.
We reserve the right to make changes in specifications and design without prior notice.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
F-801MAH-C
APPROXIMATE
ICE PRODUCTION
PER 24 HR.
Ambient
Temp. (F)
70
Water Temp. (F)
70
50
90
*
752 (341)
650 (295)
728 (330)
614 (279)
548 (249) * 552 (250)
463 (210) 437 (198) * 405 (184)
688 (312)
580 (263)
490 (222)
80
90
100
70
80
90
100
70
80
90
100
70
80
90
100
70
lbs./day (kg/day)
APPROXIMATE ELECTRIC
CONSUMPTION
* 1110
1136
--
--
--
1112
1148
* 1169
1222
87
--
--
--
1124
1160
1196
* 1251
83
--
--
--
--
1172
1209
watts
--
--
APPROXIMATE WATER
CONSUMPTION PER 24 HR.
(TOTAL)
gal. / day (l/day)
EVAPORATOR OUTLET TEMP.
°F (°C)
*
*
*
90
78
66
56
14
14
14
16
(342)
(295)
(331)
(279)
(251)
(313)
(264)
(222)
(184)
(-10)
(-10)
(-9)
(-8)
74
70
59
(249) * 66
(210)
(-10)
(-10)
(-10)
(-9)
52
14
14
14
18
(199) * 49
(-10)
(-10)
(-10)
(-8)
14
14
16
18
*
*
HEAD PRESSURE
200 (14.0)
226 (15.9)
212 (14.9)
233 (16.4)
219 (15.4)
241 (16.9)
265 (18.6)
80
90
249 (17.5) * 265 (18.6)
273 (19.2)
PSIG (kg/cm2G)
100
70
282 (19.8) * 296 (20.8)
SUCTION PRESSURE
PSIG (kg/cm2G)
*
38
(2.7)
41
(2.9)
42
(2.9)
80
90
100
42
43
43
(2.9)
(3.0)
(3.1)
42
43
44
(3.0)
(3.0)
(3.1)
42
43
48
(3.0)
(3.0)
(3.3)
*
*
TOTAL HEAT OF REJECTION
6398 BTU/h (AT 90°F / WT 70°F)
Note: The data without *marks should be used for reference.
We reserve the right to make changes in specifications and design without prior notice.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
F-801MWH-C
APPROXIMATE
ICE PRODUCTION
PER 24 HR.
Ambient
Temp. (F)
70
Water Temp. (F)
70
50
90
*
645 (293)
596 (270)
620 (281)
585 (265)
563 (255) * 550 (249)
531 (241) 521 (236) * 485 (220)
608 (276)
574 (260)
541 (246)
80
90
100
70
80
90
100
70
80
90
100
70
80
90
100
70
lbs./day ( kg/day)
APPROXIMATE ELECTRIC
CONSUMPTION
* 1083
1080
--
--
--
--
1082
1078
* 1075
1070
--
--
--
--
1081
1077
1073
--
--
--
--
1076
1072
watts
* 1068
APPROXIMATE WATER
CONSUMPTION PER 24 HR.
(TOTAL)
gal. / day (l/day)
EVAPORATOR OUTLET TEMP.
°F (°C)
*
*
*
276 (1046)
287 (1086)
342 (1294)
354 (1339)
296 (1119) * 368 (1392)
305 (1156) 381 (1442) * 693 (2622)
579 (2192)
605 (2291)
633 (2397)
20
21
21
21
(-7)
(-6)
(-6)
(-6)
20
21
21
21
(-7)
(-6)
(-6)
(-6)
21
21
21
22
(-6)
(-6)
(-6)
(-6)
*
*
HEAD PRESSURE
263 (18.5)
263 (18.5)
263 (18.5)
263 (18.5)
264 (18.6)
264 (18.6)
264 (18.6)
80
90
263 (18.5) * 263 (18.5)
263 (18.5)
PSIG (kg/cm2G)
100
70
263 (18.5) * 264 (18.6)
SUCTION PRESSURE
PSIG (kg/cm2G)
*
46
(3.2)
46
(3.3)
47
(3.3)
80
90
100
46
46
46
(3.2)
(3.2)
(3.2)
46
46
46
(3.3)
(3.3)
(3.3)
47
47
47
(3.3)
(3.3)
(3.3)
*
*
WATER FLOW FOR CONDENSER
13 gal/h (AT 90°F / WT 70°F)
PRESSURE DROP OF COOLING WATER LINE Less than 7 PSIG
HEAT OF REJECTION FROM CONDENSER
HEAT OF REJECTION FROM COMPRESSOR
5155 BTU/h (AT 90°F / WT 70°F)
1050 BTU/h (AT 90°F / WT 70°F)
Note: The data without *marks should be used for reference.
We reserve the right to make changes in specifications and design without prior notice.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
IV. Adjustment of Components
1. Adjustment of Water Regulating Valve (water-cooled model only)
Thewaterregulatingvalveoralsocalled“waterregulator”isfactory-adjusted.Noadjustment
is required under normal use. Adjust the water regulator , if necessary, using the following
procedures.
1) Attach a pressure gauge to the high-side line of the system. Or prepare a thermometer to
check the condenser drain temperature.
2)Rotatetheadjustmentscrewbyusingaflatbladescrewdriver, sothatthepressuregauge
shows 260 PSIG (R-404A models/-F type), or the thermometer reads 100 -104°F, in 5
minutesaftertheicemakingprocessstarts.Whenthepressureexceeds260PSIG,orthe
condenserdraintemperatureexceeds104°F, rotatetheadjustmentscrewcounterclock-
wise.
3) Check that the pressure or the condenser drain temperature holds a stable setting.
Adjustment Screw
Adjustment Screw
CW
CCW
Bottom View
CW - Higher
CCW - Lower
33
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Adjustment of Flake Size
To adjust the flake size, change the direction of the cutter head on the top of the auger,
according to the following procedures:
1) Remove the bolt and the cutter head.
2)Thecutterheadhastwoholes, oneforfineflake
and the other for coarse flake size. The unit is
shipped from the factory in the fine flake
position.
3) Place the cutter head so that the pin on the top of the auger fits into the selected hole.
4) Secure the cutter head by the bolt.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
V. Service Diagnosis
1. No Ice Production
PROBLEM
[1] The icemaker will
not start.
POSSIBLE CAUSE
REMEDY
a) Power Supply
1. OFF position.
1. Move to ON position.
2. Loose connection.
3. Bad contacts.
2. Tighten.
3. Check for contintinuity
and replace.
4. Blown fuse.
1. Off position.
2. Bad contacts.
4. Replace.
b) Power Switch
(Control Box)
1. Move to ON position.
2. Check for continuity
and replace.
c) Fuse (Control Box)
d) Circuit Protect Relay
1. Blown out.
1. Miswiring.
1. Check for short circuit
and replace.
1. Check power supply
voltage and wire
properly.
e) Flush Timer
f) Flush Switch
1. Flushing out.
2. Bad contacts.
1. Wait for 15 minutes.
2. Check for continuity
and replace.
1. Move to ICE position.
1. FLUSH position.
2. Bad contacts.
2. Check for continuity
and replace.
g) Transformer
1. Coil winding opened.
1. Coil winding opened.
1. Closed.
1. Replace.
1. Replace.
1. Open.
h) Control Water Valve
i) Shut-off Valve
2. Water failure.
2. Wait till water is
supplied.
j) Plug and Receptacle
(Control Box)
1. Disconnected.
1. Connect.
2. Terminal out of Plug
or Receptacle.
2. Insert Terminal back in
position
[2] Water flow does not
stop, and the
a) Water Control Relay
b) Float Switch
1. Contact fused.
2. Coil winding opened.
1. Bad contacts.
1. Replace.
2. Replace.
icemaker will not
start
1. Check for continuity
and replace.
2. Float does not move
freely.
1. Valve seat clogged
and water leaking.
1. Disconnected.
1. Bad contacts.
2. Clean or replace.
1. Clean or replace
1. Connect.
c) Flush Water Valve
d) Hoses
[3] Water has been
supplied, but the
icemaker will not
start.
a) Water Control Relay
1. Check for continuity
and replace.
b) Bin Control
1. Bad contacts.
1. Check for continuity
and replace.
2. Clean Axle and its
corresponding holes
or replace Bin Control.
2. Activator does not
move freely.
c) Gear Motor Relay
1. Coil winding opened.
2. bad contacts.
1. Replace.
2. Check for continuity
and replace.
d) Control Timer
(Printed Circuit
Board)
1. Broken.
1. Replace.
e) Gear Motor Protect
Relay
1. Coil winding opened.
2. Bad contacts.
1. Replace.
2. Check for continuity
and replace.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM
[4] Water has been
supplied, Fan Motor
starts, but Gear
Motor and
POSSIBLE CAUSE
REMEDY
a) Gear Motor Fuse
1. Blown Fuse.
1. See "3. [3]." Find out
the cause and replace
the Fuse.
(BUSSMAN GMD
1.5A)
b) Thermal Protector
(Gear Motor)
1. Bad contacts.
1. Check for continuity
and replace.
Compressor will not
start.
[5] Gear Motor and
Compressor start
but operate
a) Pressure Switch
1. Dirty Air Filter or
Condenser.
2. Ambient or
condenser water
temperature too
warm.
1. Clean.
2. Get cooler.
intermittently.
3. Condenser water
pressure too low or
off. (Water-cooled
model only)
3. Check and get
recommended
pressure.
4. Water Regulating
Valve set too high.
(Water-cooled model
only)
4. Adjust it lower.
5. Fan not rotating.
5. See "3. [1] a) Fan
Motor."
6. Refrigerant
overcharged.
6. Recharge.
7. Refrigerant line or
components
7. Clean and replace
drier.
plugged.
8. Bad contacts.
8. Check for continuity
and replace.
9. Loose connections.
1. Bad contacts.
9. Tighten.
[6] Gear Motor starts,
but Compressor will
not start or operates
intermittently.
a) X2 Relay on Control
Timer
1. Replace.Check for
continuity and replace.
2. Coil winding opened. 2. Replace Timer.
b) Starter
1. Bad contacts.
1. Check for continuity
and replace.
2. Coil winding opened. 2. Replace.
3. Loose Connections.
1. Defective.
3. Tighten.
1. Replace.
c) Start Capacitor or
Run Capacitor
d) Compressor
1. Loose connections.
1. Tighten.
2. Replace.
2. Motor winding
opened or grounded.
3. Motor Protector
tripped.
3. Find out the cause of
overheat or
overcurrent.
e) Power Supply
1. Circuit Ampacity too
low.
1. Install a larger-sized
conductor.
[7] Gear Motor and
Compressor start,
but no ice is
a) Refrigerant Line
1. Gas leaks.
1. Check for leaks with a
leak detector. Reweld
leak, replace drier and
charge with
produced.
refrigerant. The
amount of refrigerant
is marked on
Nameplate or Label.
2. refrigerant line
clogged.
2. Replace the clogged
component.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Low Ice Production
PROBLEM
[1] Low ice production
POSSIBLE CAUSE
REMEDY
1. See "1. [5] a)
Refrigerant Line."
a) Refrigerant Line
1. Gas leaks.
2. Refrigerant line
clogged.
2. Replace the clogged
component.
3. Overcharged.
3. Recharge.
1. Clean.
b) High-side Pressure
1. Dirty Air Filter or
Condenser.
Too High
2. Ambient or
condenser water
temperature too
warm.
2. Get cooler.
3. Condenser water
pressure too low or
off. [Water-cooled
model only]
3. Check and get
recommended
pressure.
4. Fan rotating too
4. See "3 [1] a) Fan
Motor."
slow.
5. Water Regulating
Valve clogged.
[Water-cooled model
only]
5. Clean.
6. Condensing unit out 6. Check condensing
of order.
unit.
c) Expansion Valve
(not adjustable)
1. Low-side pressure
too low.
1. Replace.
2. Low-side pressure
2. See if Expansion
Valve Bulb is mounted
properly, and replace
the valve if necessary.
too high.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Other
PROBLEM
[1] Abnormal noise
POSSIBLE CAUSE
REMEDY
1. Replace.
a) Fan Motor
1. Bearing worn out.
2. Fan blade deformed. 2. Replace fan blade.
3. Fan blade does not
move freely.
1. Bearings worn out,
or cylinder valve
broken.
3. Replace.
1. Replace.
b) Compressor
2. Mounting pad out of 2. Reinstall.
position.
c) Refrigerant Lines
1. Rub or touch lines or 1. Replace.
other surfaces.
d) Gear Motor (Ice
Making)
1. Bearing or Gear
worn out / damaged.
1. Replace.
e) Evaporator
1. Too much pressure 1. Replace.
loss.
2. Scale on inside wall 2. Remove Auger. Use
of Freezing Cylinder.
"SCALE AWAY" or
"LIME-A-WAY"
solution to clean
periodically. If the
water is found hard by
testing, install a
softener.
[2] Overflow from
Reservoir (Water
does not stop.)
a) Water Supply
1. Water pressure too
high.
1. Install a pressure
Reducing Valve
b) Control Water Valve 1. Diaphragm does not 1. Clean or replace.
close.
c) Float Switch
1. Bad contacts.
1. Check for continuity
and replace.
[3] Gear Motor Fuse
blown frequently.
a) Power Supply
Voltage
1. Too high or too low. 1. Connect the unit to a
power supply of
proper voltage.
b) Ice Making Unit
c) Bin Control
1. Bearings or Auger
worn out.
1. Bad contacts.
1. Replace Bearing or
Auger.
1. Check for continuity
and replace.
2. Activator does not
move freely.
2. Clean Axle and its
corresponding holes
or replace Bin Control.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
VI. Removal and Replacement of Components
IMPORTANT
Ensureallcomponents, fastenersandthumbscrewsaresecurelyinplace
after the equipment is serviced.
IMPORTANT
1. The Polyolester (POE) oils used in R-404A units can absorb moisture
quickly. Therefore it is important to prevent moisture from entering the
system when replacing or servicing parts.
2. Always install a new filter drier every time the sealed refrigeration system
is opened.
3. Do not leave the system open for longer than 15 minutes when replacing
or servicing parts.
1. Service for Refrigerant Lines
[a] Refrigerant Recovery
The icemaker unit is provided with two refrigerant access valves - one on the low-side and
one on the high-side line. Using proper refrigerant practices recover the refrigerant from the
access valves and store it in an approved container. Do not discharge the refrigerant into
the atmosphere.
[b] Evacuation and Recharge [R-404A]
1) Attach charging hoses, a service manifold and a vacuum pump to the system. Be sure
to connect charging hoses to both high-side and low-side access valves.
IMPORTANT
The vacuum level and vacuum pump may be the same as those for current
refrigerants. However, the rubber hose and gauge manifold to be used for
evacuation and refrigerant charge should be exclusively for POE oils.
2) Turn on the vacuum pump. Never allow the oil in the vacuum pump to flow backward.
3) Allow the vacuum pump to pull down to a 29.9" Hg vacuum. Evacuating period
depends on pump capacity.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
4) Close the low-side valve and high-side valve on the service manifold.
5) Disconnect the vacuum pump, and attach a refrigerant service cylinder to the high-
side line. Remember to loosen the connection, and purge the air from the hose. See
the nameplate for the required refrigerant charge. Hoshizaki recommends only virgin
refrigerant or reclaimed refrigerant which meets ARI Standard No. 700-88 be used.
6) A liquid charge is recommended for charging an R-404A system. Invert the service
cylinder. Open the high-side, service manifold valve.
7) Allow the system to charge with liquid until the pressures balance.
8) If necessary, add any remaining charge to the system through the low-side. Use a
throttling valve or liquid dispensing device to add the remaining liquid charge
through the low-side access port with the unit running.
9) Close the two refrigerant access valves, and disconnect the hoses and service
manifold.
10) Cap the access valves to prevent a possible leak.
2. Brazing
DANGER
1. Refrigerant R-404A itself is not flammable at atmospheric pressure and
temperatures up to 176° F.
2. Refrigerant R-404A itself is not explosive or poisonous. However, when
exposed to high temperatures (open flames) R-404A can be decomposed
to form hydrofluoric acid and carbonyl fluoride both of which are
hazardous.
3. Always recover the refrigerant and store it in an approved container. Do
not discharge the refrigerant into the atmosphere.
4. Do not use silver alloy or copper alloy containing arsenic.
5. Do not use R-404A as a mixture with pressurized air for leak testing.
Refrigerant leaks can be detected by charging the unit with a little
refrigerant, raising the pressure with nitrogen and using an electronic leak
detector.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Removal and Replacement of Compressor
IMPORTANT
Always install a new drier every time the sealed refrigeration system is
opened. Do not replace the drier until after all other repairs or replacement
have been made.
1) Turn off the power supply, and remove the panels.
2) Remove the terminal cover on the compressor, and disconnect the compressor wiring.
3)Recovertherefrigerantandstoreitinanapprovedcontainer, ifrequiredbyanapplicable
law.
4) Remove the discharge, suction and access pipes from the compressor using brazing
equipment.
WARNING
When repairing a refrigerant system, be careful not to let the burner flame
contact any electrical wires or insulation.
5) Remove the bolts and rubber grommets.
6)Slideandremovethecompressor.Unpackthenewcompressorpackage.Installthenew
compressor.
7) Attach the rubber grommets of the prior compressor.
8) Sandpaper the discharge, suction and access pipes.
9) Place the compressor in position, and secure it using the bolts.
10) Remove plugs from the discharge, suction and access pipes.
11) Braze the access, suction and discharge lines (Do not change this order), while purging
with nitrogen gas flowing at the pressure of 3 - 4 PSIG.
12) Install the new drier.
13) Check for leaks using nitrogen gas (140 PSIG) and soap bubbles.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
14) Evacuate the system, and charge it with refrigerant. For the air-cooled and water-cooled
models, see the nameplate for the required refrigerant charge and type. For the remote air-
cooled models, see the label on the control box.
15) Connect the terminals to the compressor, and replace the terminal cover in its correct
position.
16) Replace the panels in their correct position, and turn on the power supply.
4. Removal and Replacement of Drier
IMPORTANT
Always install a new drier every time the sealed refrigeration system is
opened. Do not replace the drier until after all other repairs or replacement
have been made.
1) Turn off the power supply, and remove the panels.
2)Recovertherefrigerantandstoreitinanapprovedcontainer, ifrequiredbyanapplicable
law.
3) Remove the drier using brazing equipment.
4) Install the new drier with the arrow on the drier in the direction of the refrigerant flow. Use
nitrogen gas at the pressure of 3 - 4 PSIG when brazing the tubings.
5) Check for leaks using nitrogen gas (140 PSIG) and soap bubbles.
6)Evacuatethesystem, andchargeitwithrefrigerant. Fortheair-cooledandwater-cooled
models, see the nameplate for the required refrigerant charge and type. For the remote
air-cooled models, see the label on the control box.
7) Replace the panels in their correct position, and turn on the power supply.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Removal and Replacement of Expansion Valve
IMPORTANT
Sometimes moisture in the refrigerant circuit exceeds the drier capacity and
freezes up at the expansion valve. Always install a new drier every time the
sealed refrigeration system is opened. Do not replace the drier until after all
other repairs or replacement have been made.
1) Turn off the power supply, and remove the panels.
2)Recovertherefrigerantandstoreitinanapprovedcontainer, ifrequiredbyanapplicable
law.
3) Remove the expansion valve bulb at the evaporator outlet.
4) Remove the expansion valve cover, and remove the expansion valve using brazing
equipment.
5) Braze the new expansion valve with nitrogen gas flowing at the pressure of 3 - 4 PSIG.
WARNING
Always protect the valve body by using a damp cloth to prevent the valve from
overheating. Do not braze with the valve body exceeding 250°F.
6) Install the new drier.
7) Check for leaks using nitrogen gas (140 PSIG) and soap bubbles.
8) Evacuate the system. Charge it with refrigerant. For the air-cooled and water-cooled
models, see the nameplate for the required refrigerant charge and type. For the remote
air-cooled models, see the label on the control box.
9)Attachthebulbtothesuctionline. Besuretosecurethebulbusingabandandtoinsulate
it.
10) Place the new set of expansion valve covers in position.
11) Replace the panels in their correct position, and turn on the power supply.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Removal and Replacement of Water Regulating Valve
(water-cooled model only)
IMPORTANT
Always install a new drier every time the sealed refrigeration system is
opened. Do not replace the drier until after all other repairs or replacement
have been made.
1) Turn off the power supply, remove the panels and close the water supply line shut-off
valve.
2) Recover the refrigerant and store it in an approved container.
3) Disconnect the capillary tube using brazing equipment.
4) Disconnect the flare-connections of the valve.
5) Remove the screws and the valve from the bracket.
6) Install the new valve, and braze the capillary tube.
7) Install the new drier.
8) Check for leaks using nitrogen gas (140 PSIG) and soap bubbles.
9) Connect the flare-connections.
10) Evacuate the system, and charge it with refrigerant. See the nameplate for the required
refrigerant charge and type.
11) Open the water supply line shut-off valve, and turn on the power supply.
12) Check for water leaks.
13) See “IV. 1. Adjustment of Water Regulating Valve.” If necessary, adjust the valve.
14) Replace the panels in their correct position.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Removal and Replacement of Evaporator Assembly
1) Turn off the power supply.
2) Remove the panels.
3) Move the flush switch to the "FLUSH" position.
4) Turn on the power supply and drain out all water from the water line.
5) Turn off the power supply.
6) Remove the strap connecting the spout to the chute assembly.
7) Remove the three thumbscrews and take off the spout from the evaporator.
Cutter
8) Remove the bolt and lift off the cutter.
9) Remove the rubber O-ring and the nylon ring at the top of the evaporator.
Extruding Head
10) Remove the four socket head cap screws and lift off the extruding head.
11) Replace the bearing inside the extruding head, if it exceeds the wear tolerance of 0.02"
or is scratched.
Note: Replacing the bearing requires a bearing press adaptor. If it is not available,
replace the whole extruding head.
Auger
12)Liftofftheauger.Iftheareaincontactwiththebearingiswornoutorthebladescratched,
replace the auger.
Evaporator
Note: Skip the following steps 13) through 15) when the evaporator does not need
replacement.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
13)Recovertherefrigerantandstoreitinanapprovedcontainer,ifrequiredbyanapplicable
law.
IMPORTANT
Always install a new drier every time the sealed refrigeration system is
opened. Do not replace the drier until after all other repairs or replacement
have been made.
14) Remove the bulb of the expansion valve.
15) Disconnect the brazing-connections of the expansion valve and the copper tube -low
side from the evaporator, using brazing equipment.
16) Remove the two truss head machine screws and the strap securing the evaporator.
17) Disconnect the three hoses from the evaporator.
18) Remove the four socket head cap screws securing the evaporator with the bearing-
lower.
19) Lift off the evaporator.
Bearing-Lower and Mechanical Seal
20) The mechanical seal consists of two parts. One moves along with the auger, and the
other is fixed on the bearing-lower. If the contact surfaces of these two parts are worn or
scratched, the mechanical seal may cause water leaks and should be replaced.
21) Remove the O-ring on the bearing-lower.
22) Remove the four bolts and the bearing-lower from the gear motor. Replace the bearing
inside the bearing-lower, if it exceeds the wear tolerance of 0.02" or is scratched.
Note: Replacing the bearing requires a bearing press adaptor. If it is not available,
replace the whole bearing-lower.
Gear Motor
23) Remove the coupling-spline on the gear motor shaft.
24) Remove the barrier on the top of the gear motor.
25) Remove the three socket head cap screws securing the gear motor.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
26) Assemble the removed parts in the reverse order of the above procedure.
WARNING
BecarefulnottoscratchthesurfaceoftheO-ring, oritmaycausewaterleaks.
Handle the mechanical seal with care not to scratch nor to contaminate its
contact surface.
27) When replacing the evaporator;
(a) Braze the new evaporator with nitrogen gas flowing at the pressure of 3 - 4 PSIG.
(b) Replace the drier.
(c) Check for leaks using nitrogen gas (140 PSIG) and soap bubbles.
(d)Evacuatethesystem.Chargeitwithrefrigerant.Fortheair-cooledandwater-cooled
models, see the nameplate for required refrigerant charge and type. For the remote
air-cooled models, see the label on the control box.
28) Move the flush switch to the "ICE" position.
29) Replace the panels in their correct position.
30) Turn on the power supply.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Rubber O-ring
Nylon Ring
Bolt
Washer
Auger
Cutter
Extruding
Head
Washer
Mechanical
Seal
Socket Head
Cap Screw
O-ring
Bearing
- Lower
Evaporator
Washer
Bolt
Socket Head
Cap Screw
Washer
Coupling
- Spline
Barrier
Gear Motor
48
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Removal and Replacement of Fan Motor
1) Turn off the power supply and remove the panels.
2) Remove the wire connectors from the fan motor leads.
3) Remove the fan motor bracket and fan motor.
4) Install the new fan motor.
5) Replace the fan motor bracket and the wire connectors.
6) Replace the panels in their correct position, and turn on the power supply.
9. Removal and Replacement of Control Water Valve
1) Turn off the power supply, remove the panels and close the water supply line shut-off
valve.
2) Disconnect the terminals from the control water valve.
3) Loosen the fitting nut on the control water valve inlets, and remove the control water
valve. Do not lose the packings inside the fitting nut.
4) Remove the water supply hose from the control water valve.
5) Install the new control water valve.
6) Assemble the removed parts in the reverse order of the above procedure.
7) Open the water supply line shut-off valve.
8) Check for water leaks.
9) Replace the panels in their correct position, and turn on the power supply.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Removal and Replacement of Flush Water Valve
1) Turn off the power supply, remove the panels and close the water supply line shut-off
valve.
2) Remove the clamp and disconnect the hose from the flush water valve.
Note: Water may still remain inside the evaporator. Be sure to drain the water into the
drain pan.
3) Disconnect the terminals from the flush water valve.
4) Remove the flush water valve from the bracket.
5) Remove the drain pipe from the flush water valve.
6) Connect the drain pipe to the new flush water valve, and place the valve in position.
7) Connect the hose to the flush water valve and secure it with the clamp.
8) Pour water into the reservoir, and check for water leaks on the flush water valve.
9) Open the water supply line shut-off valve, and turn on the power supply.
10) Move the flush switch to the "ICE" position.
11) Check for water leaks.
12) Move the flush switch to the "FLUSH" position, and make sure water is flushing.
13) Move the flush switch to the "ICE" position.
14) Replace the panels in their correct position.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
VII. Cleaning and Maintenance
IMPORTANT
Ensureallcomponents,fastenersandthumbscrewsaresecurelyinplaceafter
any maintenance or cleaning is done to the equipment.
1. Preparing the Icemaker for Long Storage
WARNING
Whenshuttingofftheicemakerforanextendedtime,drainoutallwaterfromthe
water line and remove the ice from the storage bin. The storage bin should be
cleaned and dried. Drain the icemaker to prevent damage to the water supply
line at sub-freezing temperatures, using air or carbon dioxide. Shut off the
icemaker until the proper ambient temperature is resumed.
[Air-Cooled and Remote Air-Cooled Models]
1) Run the icemaker with the water supply line shut-off valve closed.
2) Open the drain valve and blow out the water inlet line by using air pressure.
3) Turn off the power supply.
4) Remove the front panel.
e
5) Move the flush switch on the control box to the
“FLUSH” position.
6) Turn on the power supply, and then drain out all
water from the water line.
7) Turn off the power supply.
8) Turn off the power switch on the control box.
9) Replace the front panel in its correct position.
10) Close the drain valve.
Air or CO2
11) Remove all ice from the storage bin, and clean the bin.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
[Water-Cooled Models]
1) Turn off the power supply and wait for 3 minutes.
2) Turn on the power supply and wait for 20 seconds.
3) Close the water supply line shut-off valve.
4) Open the drain valve and quickly blow the water supply line from the drain valve to drain
water in the condenser.
5) Follow the above steps 3) through 11) in [Air-Cooled and Remote Air-Cooled Models].
2. Cleaning and Sanitizing Instructions
WARNING
1. HOSHIZAKI recommends cleaning this unit at least once a year. More
frequent cleaning, however, may be required in some existing water
conditions.
2. To prevent injury to individuals and damage to the icemaker, do not use
ammonia type cleaners.
3. Always wear liquid-proof gloves to prevent the cleaning and sanitizing
solutions from coming into contact with skin.
[a] Cleaning Solution
Dilute 4.8 fl. oz. (142 ml) of recommended cleaner Hoshizaki “Scale Away” or
“LIME-A-WAY” (Economics Laboratory, Inc.) with 0.8 gallons (3 l) of warm water. This is a
minimum amount. Make more solution if necessary.
IMPORTANT
For safety and maximum effectiveness, use the solution immediately after
dilution.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
[b] Cleaning Procedure
The cleaning process will remove lime deposits from the water system.
1) Remove the front panel and top panel, then turn off the power supply.
2) Close the water supply line shut-off valve.
3) Remove all ice from the storage bin.
4) Move the flush switch to the “FLUSH” position.
5) Turn on the power supply and drain out all water from the water line.
6) Turn off the power supply.
7) Remove the strap connecting the spout to the chute assembly.
8) Remove the thumbscrews securing the spout and lift it off.
9) Pour the cleaning solution over the extruding head until the evaporator assembly and the
reservoir are filled and the solution starts to overflow into the drain pan.
Note: If there is excess scale on the extruding head, fill the evaporator assembly and
reservoir as described above, then use a clamp on the reservoir hose between the
reservoir and evaporator assembly to block flow. Pour additional cleaning fluid
over the extruding head until the evaporator assembly is completely full.
10) Replace the spout and strap in their correct positions.
11) Allow the icemaker to sit for about 10 minutes before operation. If you placed a clamp on
the reservoir hose in step 9, remove it before operation.
12) Move the flush switch to the “ICE” position, then turn on the power supply. Replace the
top panel and front panel in their correct positions. Make ice using the solution until the
icemaker stops making ice.
13) Remove the front panel.
14) Move the flush switch to the “FLUSH” position to drain the remainder of the solution.
15) After the solution is drained, move the flush switch to the “ICE” position.
16) Replace the front panel in its correct position.
17) Open the water supply line shut-off valve and supply water to the reservoir.
18) When the gear motor starts, remove the front panel and turn off the power supply.
19) Drain out all water from the water line. See 4) through 6).
53
Download from Www.Somanuals.com. All Manuals Search And Download.
[c] Sanitizing Solution
Dilute 2.5 fl. oz. (74 ml or 5 tbs) of IMS-II Sanitizer or a 5.25% sodium hypochlorite solution
(chlorine bleach) with 5 gallons (19 l) of warm water.
IMPORTANT
For safety and maximum effectiveness, use the solution immediately after
dilution.
[d] Sanitizing Procedure - Initial
The sanitizing process will sanitize the icemaker.
1) Close the water supply line shut-off valve.
2) Remove the strap connecting the spout to the chute assembly.
3) Remove the thumbscrews securing the spout and lift it off. Remove the rubber O-ring and
nylon O-ring at the top of the cylinder and also remove the packing between the spout
and the chute.
4) Pour the sanitizing solution over the extruding head until the evaporator assembly and
the reservoir are filled and the solution starts to overflow into the drain pan.
5) Remove the two thumbscrews securing the proximity switch to the chute assembly.
6) Remove the chute assembly from the icemaker.
7) Remove the packing at the bottom of the ice chute.
8) Remove the three ties and the chute insulation.
9) Remove the six wing nuts and two baffles.
10) Remove the two thumbscrews, the plate and the packing from the top of the ice chute,
then remove the bin control assembly by sliding it slightly toward the chute opening and
lifting it off.
11) Disassemble the bin control assembly by removing the two snap pins, shaft and
actuator.
12) Soak the removed parts in .25 gallons (1 l) of sanitizing solution for 10 minutes then
wipe them down.
13) Rinse the parts thoroughly.
IMPORTANT
If the solution is left on these parts, they will rust.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
14) Replace all parts in their correct positions.
IMPORTANT
When installing the baffles, make sure that the bent surface (the one without the
studs) faces the actuator so that the bent surface can guide the ice to the center
of the actuator.
15) Move the flush switch to the “ICE” position, then turn on the power supply. Replace the
top panel and front panel in their correct positions. Make ice using the solution until the
icemaker stops making ice.
[e] Sanitizing Procedure - Final
1) Remove the front panel and top panel, then turn off the power supply.
2) Move the flush switch to the “FLUSH” position.
3) Turn on the power supply and drain out all water from the water line.
4) Turn off the power supply.
5) Remove the strap connecting the spout to the chute assembly.
6) Remove the thumbscrews securing the spout and lift it off.
7) Pour the sanitizing solution over the extruding head until the evaporator assembly and
the reservoir are filled and the solution starts to overflow into the drain pan.
8) Replace the spout and strap in their correct positions.
9) Allow the icemaker to sit for about 10 minutes before operation.
10) Move the flush switch to the “ICE” position, then turn on the power supply. Replace the
top panel and front panel in their correct positions. Make ice using the solution until the
icemaker stops making ice.
11) Remove the front panel.
12) Move the flush switch to the “FLUSH” position to drain the remainder of the solution.
13) After the solution is drained, move the flush switch to the “ICE” position.
14) Replace the front panel in its correct position.
15) Open the water supply line shut-off valve and supply water to the reservoir.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
16) When the gear motor starts, remove the front panel and turn off the power supply.
17) Drain out all water from the water line. See 2) and 3).
18) Move the flush switch to the “ICE” position and run the icemaker.
19) Turn off the power supply after 30 minutes.
20) Pour warm water into the storage bin to melt all ice, and then clean the bin liner with the
solution.
21) Flush out any solution from the storage bin.
22) Turn on the power supply and start the automatic icemaking process.
IMPORTANT
1. After cleaning, do not use ice made from the sanitizing solution. Be careful
not to leave any solution in the storage bin.
2. Follow carefully any instructions provided with the bottles of cleaning or
sanitizing solution.
3. Never run the icemaker when the reservoir is empty.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Maintenance
IMPORTANT
1. This icemaker must be maintained individually, referring to the instruction
manual and labels provided with the icemaker.
2. To have the optimum performance of this icemaker, the following
consumable parts need periodical inspection, maintenance and
replacement:
Extruding Head
Housing
Gear Motor
Auger
Mechanical Seal
These parts should be inspected at least once a year or every 10,000 hours
of operation. Their service life, however, depends on water quality and
environment. More frequent inspection and maintenance are recommended.
Consult with your local distributor about inspection and maintenance
service. To obtain the name and phone number of your local distributor, call
Hoshizaki Technical Support at 1-800-233-1940.
1) Stainless Steel Exterior
To prevent corrosion, wipe the exterior occasionally with a clean and soft cloth. Use
a damp cloth containing a neutral cleaner to wipe off oil or dirt build up.
2) Storage Bin and Scoop
* Wash your hands before removing ice. Use the plastic scoop provided (bin
accessory).
* The storage bin is for ice use only. Do not store anything else in the bin.
* Keep the scoop clean. Clean using a neutral cleaner and rinse thoroughly.
* Clean the bin liner using a neutral cleaner. Rinse thoroughly after cleaning.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
3) Air Filter (air-cooled model only)
A plastic mesh air filter removes dirt or dust from the air, and keeps the condenser
from getting clogged. As the filter gets clogged, the icemaker’s performance will be
reduced. Check the filter at least twice a month. When clogged, use warm water and
a neutral cleaner to wash the filter.
4) Condenser (except water-cooled model)
Check the condenser once a year, and clean if required by using a brush or vacuum
cleaner. More frequent cleaning may be required depending on the location of the
icemaker.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Grizzly MP3 Docking Station G9859 User Manual
Grundig CRT Television GUVCD2800 User Manual
Hamilton Beach Oven 32600 User Manual
HANNspree Flat Panel Television LT11 23A1 User Manual
Harbor Freight Tools Lathe 93212 User Manual
Healthrider Treadmill HMTL796080 User Manual
Honeywell Thermostat 7351F User Manual
Hotpoint Washer BHWM149 User Manual
HP Hewlett Packard Network Card 5991 5565 User Manual
Ice O Matic Ice Maker CD 40022 User Manual