Honeywell Video Game Keyboard HJC5000 User Manual
UltraKey Lite  
Keyboard controller for VideoBloX  
and MAXPRO-Net Matrix Systems  
HJC5000  
Installation and User Guide  
Document 800-07422 – Rev A – 08/10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation and User  
Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Revisions  
Issue  
Date  
Revisions  
800-03854 rev A  
800-03854 rev B  
800-03854 rev C  
02/2009  
03/2009  
04/2009  
New document.  
Updated the MaxPRO map code.  
Corrected the controller login PIN code; corrected IP address p. 59;  
updated images for quality  
800-07422 rev A  
08/2010  
Revisions to Step 3: Configure Address, Baud Rate or IP for VideoBloX  
Mode; Step 4: Configure VideoBloX Mode Default Settings While Powering  
Up; Step 4: Configure the Controller for an Ethernet Connection; added  
Step 5: Setting the Keyboard Address While Powering Up; and, the System  
Configuration Menu screen.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Explanation of Symbols  
WARNING!  
The exclamation point in a red octagon is a WARNING. Failure to take  
or avoid a specific action could result in physical harm to a person  
or irreparable damage to equipment.  
Caution The lightning flash with arrowhead symbol within an equilateral triangle  
alerts the user to the presence of uninsulated dangerous voltage within the  
enclosure of the product that may be of sufficient magnitude to  
constitute a risk of electric shock to the person  
Caution The exclamation point in a yellow equilateral triangle is a Caution. Failure  
to take or avoid a specified action could result in loss of data or damage  
to equipment and may contain important operating and maintenance  
servicing information.  
FCC Compliance Statement  
Information to the User: This equipment has been tested and found to comply with the limits for a Class B digital  
device. Pursuant to Part 15 of the FCC Rules, these limits are designed to provide reasonable protection against  
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency  
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to  
radio communications. However, there is no guarantee that interference will not occur in a particular installation.  
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning  
the equipment off and on, the user is encouraged to try to correct the interference. For example, try orienting or  
relocating the receiving antenna, increasing the separation between the equipment and receiver, or connecting the  
equipment to an outlet on a different circuit.  
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device  
may not cause harmful interference, and (2) this device must accept any interference received, including interference  
that may cause undesired operation.  
Document 800-07422 Rev A  
08/10  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Changes or modifications not expressly approved by the party responsible for compliance  
could void the user’s authority to operate the equipment.  
Users of the product are responsible for checking and complying with all federal, state and  
local laws and statutes concerning the monitoring and recording of video and audio signals.  
Honeywell Systems Group shall not be held responsible for the use of this product in violation  
of current laws and statutes.  
Canadian Compliance Statement  
This Class B digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.  
European Compliance Statement  
The manufacturer declares that the equipment supplied with this guide is compliant with the essential protection  
requirements of the EMC directive 2004/108/EC and the Low Voltage Directive LVD 2006/95/EC, conforming to the  
requirements of standards EN 55022 for emissions, EN 50130-4 for immunity, and EN 60065 for Electrical Equipment  
safety.  
Caution Users of the product are responsible for checking and complying with all federal, state, and local  
laws and statutes concerning the monitoring and recording of video and audio signals.  
Honeywell shall not be held responsible for the use of this product in violation of current laws and  
statutes.  
Warnings and Cautions  
Read the following cautions and warnings prior to installation and use of this product.  
Installation and servicing must be performed by qualified personnel in accordance with  
local codes and regulations.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Consider using a UPS source to ensure satisfactory performance.  
Using replacement parts or accessories other than the original manufacturers may invalidate the  
warranty.  
CAUTION  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,  
DO NOT REMOVE COVER (OR BACK).  
NO USER-SERVICEABLE PARTS INSIDE.  
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.  
Important Safety Instructions  
BEFORE OPERATING OR INSTALLING THE UNIT, READ AND FOLLOW ALL INSTRUCTIONS.  
AFTER INSTALLATION, retain the safety and operating instructions for future reference  
1. HEED WARNINGS - Adhere to all warnings on the unit and in the operating instructions.  
2. INSTALLATION  
•
•
Install in accordance with the manufacturer’s instructions.  
Installation and servicing should be performed only by qualified and experienced technicians to conform to  
all local codes and to maintain your warranty.  
•
Do not install the unit in an extremely hot or humid location, or in a place subject to dust or mechanical  
vibration. The unit is not designed to be waterproof. Exposure to rain or water may damage the unit.  
3. POWER SOURCES - This product should be operated only from the type of power source indicated on the  
marking label. If you are not sure of the type of power supplied to your facility, consult your product dealer or  
local power company.  
4. HEAT - Situate away from items that produce heat or are heat sources such as radiators, heat registers, stoves,  
or other products (including amplifiers).  
5. WATER AND MOISTURE - Do not use this unit near water or in an unprotected outdoor installation, or any area  
classified as a wet location.  
6. ATTACHMENTS - Do not use attachments not recommended by the product manufacturer as they may result in  
the risk of fire, electric shock, or injury to persons.  
7. ACCESSORIES - Only use accessories specified by the manufacturer.  
8. CLEANING - Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.  
9. SERVICING - Do not attempt to service this unit yourself as opening or removing covers may expose you to  
dangerous voltage or other hazards. Refer all servicing to qualified service personnel.  
Document 800-07422 Rev A  
08/10  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
10. REPLACEMENT PARTS - When replacement parts are required, be sure the service technician has used  
replacement parts specified by the manufacturer or have the same characteristics as the original part.  
Unauthorized substitutions may result in fire, electric shock or other hazards.  
Warranty and Service  
Subject to the terms and conditions listed on the Product Warranty Card, during the warranty period Honeywell will  
repair or replace, at its sole option, free of charge, any defective products returned prepaid.  
In the event you have a problem with any Honeywell product, call Customer Service for assistance or to request a  
Return Merchandise Authorization (RMA) number. Be sure to have the model number, serial number, and the nature  
of the problem available for the technical service representative.  
In the U.S.A. and Canada, call 1.800.796.2288. See the back cover for other contact details.  
Prior authorization must be obtained for all returns, exchanges, or credits. Items shipped to Honeywell without a  
clearly identified Return Merchandise Authorization (RMA) number may be refused.  
WEEE (Waste Electrical and Electronic Equipment). Correct disposal of  
this product (applicable in the European Union and other European  
countries with separate collection systems). This product should be  
disposed of, at the end of its useful life, as per applicable local laws,  
regulations, and procedures  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
UltraKey Lite Controller Installation and User Guide  
Contents  
1
About this Document and the UltraKey Lite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
Document Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
Finding More Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Typographical Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
UltraKey Lite Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17  
Shipping Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
UltraKey Lite Port Connections and Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
2
3
4
5
Using the UltraKey Lite Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21  
Logging Onto the Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21  
Using the UltraKey Lite to Navigate the LCD Menus. . . . . . . . . . . . . . . . . . . . . . . . . . . . 22  
VideoBloX Key Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24  
MAXPRO Key Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27  
Installing UltraKey Lite with VideoBloX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31  
Navigating the LCD Configuration Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31  
Installing and Configuring a Serial Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32  
Installing and Configuring an Ethernet Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36  
(Optional) Configuring UltraKey Lite Using the Web Browser . . . . . . . . . . . . . . . . . . . . . . . 41  
Installing UltraKey Lite with MAXPRO-Net . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47  
Navigating the LCD Configuration Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47  
Installing and Configuring a Serial Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49  
Installing and Configuring an Ethernet Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56  
(Optional) Configuring UltraKey Lite Using the Web Browser . . . . . . . . . . . . . . . . . . . . . . . 60  
System Administration and Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65  
System Administration Using the Controller LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65  
System Administration Using the Web Browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68  
Document 800-07422 Rev A  
08/10  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
UltraKey Lite Controller Installation and User Guide  
Figures  
Figure 1-1  
Figure 1-2  
Figure 2-1  
Figure 2-2  
Figure 3-1  
Figure 3-2  
Figure 3-3  
Figure 3-4  
Figure 3-5  
Figure 3-6  
Figure 3-7  
Figure 3-8  
Figure 3-9  
Figure 3-10  
Figure 3-11  
Figure 3-12  
Figure 3-13  
Figure 4-1  
Figure 4-2  
Figure 4-3  
Figure 4-4  
Figure 4-5  
Figure 4-6  
Figure 4-7  
Figure 4-8  
Figure 4-9  
Figure 4-10  
Figure 4-11  
Figure 4-12  
Figure 4-13  
Figure 4-14  
Figure 4-15  
Figure 4-16  
Figure 4-17  
Figure 5-1  
UltraKey Lite Port Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
Terminal Box Front and Back Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20  
UltraKey Lite Controller Keyboard Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . 22  
The UltraKey Navigation Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23  
LCD and LCD Navigation Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32  
VideoBloX LCD Configuration Menu Tree. . . . . . . . . . . . . . . . . . . . . . . . . . . 32  
AC Power Adapter with CEE 7/16 Europlug . . . . . . . . . . . . . . . . . . . . . . . . . 33  
RJ45 to DB9 Male Adapter for VideoBloX and VideoBloX Lite CPUs. . . . . . . . . . . . . 34  
Direct RJ45 Serial Port Connection for VideoBloX NetCPUs . . . . . . . . . . . . . . . . . 34  
VideoBloX Serial Port RS422 Connection Example. . . . . . . . . . . . . . . . . . . . . . 34  
Ethernet Port Connections to VideoBloX . . . . . . . . . . . . . . . . . . . . . . . . . . . 37  
UltraKey Lite Login Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42  
System Configuration Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42  
VideoBloX Configuration Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43  
Serial Port Configuration Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44  
IP Configuration Tab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44  
DynKey Configuration Tab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45  
LCD and Navigation Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48  
MAXPRO LCD Menu Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48  
RS232 Serial Port Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50  
RS232 Serial Port Connection and MegaPIT . . . . . . . . . . . . . . . . . . . . . . . . . 50  
RS232 Serial Port Connection and MX18 . . . . . . . . . . . . . . . . . . . . . . . . . . . 51  
AC Power Adapter with CEE 7/16 Europlug . . . . . . . . . . . . . . . . . . . . . . . . . 51  
RJ45 to DB9 Female Adapter (RS232) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51  
RS422 to RS232 Converter Using the Terminal Box (RS422). . . . . . . . . . . . . . . . . 52  
RS232 Serial Port Connection and Terminal Box RS422 . . . . . . . . . . . . . . . . . . . 53  
RS232 Serial Port Connection, MX18 and the Terminal Box . . . . . . . . . . . . . . . . . 53  
Ethernet Port Connections to MAXPRO-Net . . . . . . . . . . . . . . . . . . . . . . . . . 56  
UltraKey Lite Login page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61  
System Configuration Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61  
MAXPRO Configuration Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62  
Serial Port Configuration Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63  
IP Configuration Tab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63  
DynKey Configuration Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64  
Software Upgrade Warning Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69  
Document 800-07422 Rev A  
08/10  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Figure 5-2  
Figure 5-3  
Change Password Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69  
System Configuration LCD Menu Tree - All Modes . . . . . . . . . . . . . . . . . . . . . . 70  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
UltraKey Lite Controller Installation and User Guide  
Tables  
Table 1-1  
Table 1-2  
Table 2-1  
Table 2-2  
Table 2-3  
Table 3-1  
Table 3-2  
Table 3-3  
Table 4-1  
Table 4-2  
Table 4-3  
Table 4-4  
Table 5-1  
UltraKey Lite Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17  
Shipping Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
LCD Menu Navigation During Set Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23  
VideoBloX Key Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24  
MAXPRO Key Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27  
Serial Port COM1 and COM2 Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . 33  
RJ45 Ethernet Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37  
Setting the Keyboard Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41  
Serial Port COM1 and COM2 Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . 49  
Terminal Box COM1 and COM2 Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . 52  
RJ45 Ethernet Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56  
Setting the Keyboard Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60  
HJC5000 UltraKey Lite Controller Default Settings. . . . . . . . . . . . . . . . . . . . . . . 67  
Document 800-07422 Rev A  
08/10  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1
About this Document and the UltraKey Lite  
In this section:  
•
•
•
•
•
•
Document Overview, page 15  
Finding More Information, page 16  
Typographical Conventions, page 16  
UltraKey Lite Specifications, page 17  
Shipping Checklist, page 18  
UltraKey Lite Port Connections and Descriptions, page 19  
The UltraKey Lite (HJC5000) is a replacement for the Honeywell HEGSBLX controller and  
is compatible with Honeywell VideoBloX and MAXPRO-Net Video Matrix Systems.  
The UltraKey Lite has these modes available depending on the installation:  
•
•
MAXPRO: For use with MAXPRO-Net Matrix System installations.  
VideoBloX: For use with VideoBloX Matrix System installations.  
Note  
This installation and user guide describes the Honeywell VideoBloX and  
MAXPRO-Net Video Matrix mode installation and set-up. Future product and  
documentation releases will include the Standalone mode for PTZ and DVR  
functionality.  
Document Overview  
The following is included in this user guide:  
•
•
UltraKey Lite controller user instructions (Chapter 2).  
Installation/connection and configuration instructions specific to VideoBloX  
(Chapter 3) and MAXPRO-Net (Chapter 4).  
•
System Administration and troubleshooting (Chapter 5).  
Document 800-07422 Rev A  
08/10  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
About this Document and the UltraKey Lite  
Finding More Information  
Refer to the online literature library to access other electronic documents in PDF format  
including data sheets, quick references, installation and user guides, specifications,  
software and product notices: http://www.honeywellvideo.com. Also see the back cover  
for international web sites and contact details.  
Typographical Conventions  
This document uses these typographical conventions:  
Font  
What it represents  
Example  
Use of an arrow  
Use of an arrow between keys or tabs indicates 1. On the controller, press Alt > Clr to enter  
between items >  
the order to select a menu item from the LCD or  
a web browser. You may be using keys on the  
controller or a mouse to click and select a tab on  
a web browser  
the System Configuration: System Set  
menu.  
The System Set: Mode screen displays.  
Lucida  
Values of editable fields that are mentioned in The Time from field can be set to  
the body text of the document for reference  
purposes, but do not need to be entered as part  
of a procedure.  
Hours:Minute:Seconds.  
Text strings displayed on the screen.  
Syntax.  
The message Unauthorized displays.  
(object) entered  
Swiss721 BT Bold Words or characters that are part of the task  
process and identify a field and an action that  
must be typed.  
Enter the password 1234.  
Menu titles and other items you select.  
Double-click Open from the File menu.  
Buttons you click on a web browser to perform Click Exit to close the program.  
actions.  
Pressing a key on the keyboard.  
Press and hold Logon.  
Courier  
Text that displays on the LCD screen  
The LCD menu IPAddr Changeddisplays.  
Italic  
Placeholders: words that vary depending on the user name  
situation.  
Cross-reference to external source.  
Cross-reference within document.  
Refer to the System Administrator Guide.  
See Chapter 2, Installation.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
UltraKey Lite Controller Installation and User Guide  
UltraKey Lite Specifications  
Table 1-1  
UltraKey Lite Specifications  
Value  
Parameter  
Power Requirements  
10.8 to 13.2 VDC @ 1 Ampere (A) or POE (48 VDC, Class 3)  
Connector Types  
LCD  
1×Ethernet (10Base-T, 100Base-TX) RJ45 with LED  
1×RS232/422/485 RJ45 with LED  
Type: STN, Positive Image  
Backlight: Blue-White  
Characters: 122×32 Dots  
USB  
Type: A  
Version: USB1.1 (For USB PC Keyboard)  
EN55022 for radiated and conducted emissions  
Dimensions: 408 mm (L) × 215 mm (W) × 105 mm (H)  
Gross Weight: 3.2 kg  
Compliance  
Mechanical  
Cover material: ABS+PC (cool gray)  
Operating Temperature: -10 to +55 deg C  
Storage Temperature: -40 to +75 deg C  
Humidity: 0 to 95% RH (non-condensing)  
Environment  
Document 800-07422 Rev A  
08/10  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
About this Document and the UltraKey Lite  
Shipping Checklist  
The following is included with your UltraKey Lite Controller shipment. Use of accessories  
is dependent on the type of installation. Ultrakey Lite can be connected to the matrix  
system either by serial port or Ethernet RJ45 connections.  
Table 1-2  
Shipping Checklist  
Use with...  
Quantity  
Part  
1
1
Ultrakey Lite keyboard controller  
All installations.  
All installations.  
Ultrakey Lite installation and user  
guide  
1 box  
Power adapter with plugs for  
100-240 VAC, 12 VDC, 50-60 HZ,  
1 A, 12 W  
Plug adapters depend on local electrical current. Four  
models are included:  
•
•
•
CEE 7/16 (Europlug 2.5 A/250V unearthed)  
NEMA 1-15 (North American 15 A/125V ungrounded)  
BS1363 (British 13A /230-240V 50 Hz earthed and  
fused)  
•
CPCS-CCC (Chinese 10 A/250V)/AS 3112 ; Australian  
10 A/240V).  
1
2
Connector adapter, RJ45 to DB9  
male, for RS422  
Backwards compatibility with VideoBloX and  
VideoBloX Lite CPU installations. VideoBloX  
master port.  
Connector adapter, RJ45 to DB9  
female, for RS232  
Backwards compatibility with MAXPRO-Net CPU  
installations.  
2
1
RJ45 network cable, 2 meters  
All installations.  
RJ45 cross-over Ethernet cable, 2  
meters, blue  
Used to connect a PC directly to the Controller for web  
browser configurations.  
1
1
1
RJ11 4X6 flat ribbon cable, 2 meters  
Function key overlay  
To connect from a MAXPRO and MX18 to the UltraKey Lite.  
For use with VideoBloX installations.  
Terminal box  
For additional device connection requirements.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
UltraKey Lite Controller Installation and User Guide  
UltraKey Lite Port Connections and Descriptions  
Figure 1-1  
UltraKey Lite Port Connections  
Power  
RJ45  
Ethernet  
RS232 and RS422/485  
Serial port  
USB  
8
1
8
1
Pins numbered from right to left  
DC Power Port  
Ethernet Port  
Supports 12V ( 10%) DC/1 A power input. Use the power adapter included with the  
shipment and insert one of the four adapters based on your local power requirements.  
Note  
Ethernet is used to connect to the controller web browser, MAXPRO-Net or  
VideoBloX NetCPU.  
•
10/100M Ethernet PoE (power over Ethernet) input. If PoE is the power input, it is  
not recommended to connect this network with an outside building.  
•
•
TCP/IP protocol on the controller.  
For VideoBloX, the controller address range can be between 1 and 32. For  
MAXPRO-Net, the address range can be between 1 and 99.  
Document 800-07422 Rev A  
08/10  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
About this Document and the UltraKey Lite  
RS232, RS422/485 Serial Port  
Note  
These ports are used to connect to MAXPRO-Net RS232 or RS422 and to  
VideoBloX NetCPU, Standard CPU and Lite CPU RS422.  
An isolated surge protection is suggested when using RS485/RS422 and when cabling  
between buildings.  
Note  
For MAXPRO net installations, COM1 (RS422) and COM2 (RS485) are  
configured using the controller LCD menu and cannot be used at the same  
time.  
Note  
Serial port 1 can be either RS485 or RS422. Serial port 2 is only RS232.  
Terminal Box  
Use the terminal box RJ45 port and 8-pin terminal plug as required for compatibility and  
connectivity options. It can be used to break out the RJ45 cable when wiring to existing  
infrastructure is required.  
Figure 1-2  
Terminal Box Front and Back Ports  
RS232 DB9  
Serial port  
RS232 and RS422/485 8-pin  
Terminal plug (pin numbers can  
be assigned by user)  
RJ45 Ethernet  
USB Port  
The USB port is not used with VideoBloX or MAXPRO-net.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
2
Using the UltraKey Lite Controller  
You may need to learn how to use the UltraKey Lite both before and after you begin  
configuring. In this section:  
•
•
•
•
Logging Onto the Controller, page 21  
Using the UltraKey Lite to Navigate the LCD Menus, page 22  
VideoBloX Key Functions, page 24  
MAXPRO Key Functions, page 27  
Note  
Key availability is dependent on the mode selected. Functions only used with  
the Standalone Mode (for PTZ/DVR functions) are not described in this  
document and will be included in future releases.  
Logging Onto the Controller  
1. Connect the keyboard with a power adapter (12V ( 10%) DC/1 A included) or a  
network cable with PoE.  
2. To configure the main menu settings, press Alt > Clr.  
3. Enter the PIN password 3434.  
Note  
If an invalid password is entered, a message displays and the controller  
buzzes. Repeat the steps to log on.  
When you are in the Password menu, press Alt > Clr again to exit the  
Password menu.  
Document 800-07422 Rev A  
08/10  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Using the UltraKey Lite Controller  
Using the UltraKey Lite to Navigate the LCD Menus  
There are a variety of ways to navigate both the LCD menus during configuration and set  
up as well as during normal operation with your matrix system. Figure 2-1 shows all of the  
keys and other elements of the UltraKey Lite controller. See Table 2-2 for UltraKey Lite key  
functions when used with a VideoBloX system. See Table 2-3 for UltraKey Lite key functions  
when used with a MAXPRO-Net system.  
Figure 2-1  
UltraKey Lite Controller Keyboard Layout  
1
4
6
8
10 12  
11  
14  
2
3
5
7
9
13  
15  
12:00 4/6/09  
Menu Setup Down  
View  
Tour  
1
4
2
5
8
0
3
6
Alarm  
Seq  
Set  
Review  
Search  
31  
30  
+
16  
+
+
Focus  
—
Iris  
—
PTZ  
call  
7
9
Focus  
—
F2  
F7  
F5  
F1  
F3  
F8  
F4  
F9  
Alt  
Clr  
Ent  
F6  
F10  
Mon  
A
M o n  
B
Login  
29  
28  
27  
26  
25  
24  
23  
21 20  
18  
17  
22  
19  
See Figure 2-2 for a brief overview of the three main navigation options. See Table 2-1 for  
specific methods to navigate the LCD during installation and set up.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
UltraKey Lite Controller Installation and User Guide  
Figure 2-2  
The UltraKey Navigation Controls  
Touch Pad and Ring  
Forward key (or up)  
Right arrow key  
Touch pad ring  
Left arrow key  
Touch pad - Use like a  
laptop mouse pad  
Backward or reverse key  
(or down)  
LCD Keys  
LCD  
Left arrow key  
Right arrow key  
Down arrow key  
Up arrow key  
Joystick  
Move the joystick left and right or up  
and down to navigate the menus  
Table 2-1  
Options  
To confirm a change or enter the You can use any of these ways to access the LCD:  
LCD Menu Navigation During Set Up  
Task  
current menu  
•
•
•
•
KEYS: Press Ent  
TOUCH PAD RING: Press the right arrow key  
JOYSTICK: Move right  
LCD KEYS: Special case: to enter the Set Up menu, press the LCD center  
key (not labeled)  
To cancel an operation or return to You can use any of these ways to access the LCD:  
the previous level of the menu  
•
•
•
•
KEYS: Press Alt > Clr  
TOUCH PAD: Rotate your finger in a counter-clockwise motion  
TOUCH PAD RING: Press the left arrow key  
JOYSTICK: Move left  
To view or switch between the  
menu items of the same level  
You can use any of these ways to access the LCD:  
•
•
•
•
LCD KEYS: Press up/down arrow keys  
TOUCH PAD: Rotate your finger clockwise or counter-clockwise  
TOUCH PAD RING: Press the forward/backward arrows  
JOYSTICK: Move up/down  
Document 800-07422 Rev A  
08/10  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Using the UltraKey Lite Controller  
Table 2-1  
LCD Menu Navigation During Set Up (cont’d)  
Task  
Options  
To move back through the menus  
one level at a time  
•
KEYS: Press Alt > Clr  
To scroll through the top level  
menu options  
•
•
•
•
LCD KEYS: Press the right/left arrow keys  
TOUCH PAD: Rotate your finger clockwise or counter-clockwise  
TOUCH PAD RING: Press the right / left  
JOYSTICK: Move right/left  
arrows  
To scroll through the secondary  
level menu options  
You can use any of these ways to access the LCD:  
•
•
•
•
LCD KEYS: Press the up/down arrow keys  
TOUCH PAD: Rotate your finger clockwise or counter-clockwise  
TOUCH PAD RING: Press the forward/backward arrows  
JOYSTICK: Move up/down  
To correct errors  
•
KEYS: Press Clr  
VideoBloX Key Functions  
Note  
Use Figure 2-1 to locate each key as labeled in the ID column.  
Note  
The keyboard supports dynamic key configuration. The key functions listed in  
Table 2-2 are all default functions. Contact Honeywell Technical Support or  
refer to the applicable VideoBloX manual.  
Table 2-2  
VideoBloX Key Functions  
ID  
2
Key Description  
Function in Camera Mode  
PCK (Cam Mode) PCK (Device Mode)  
Alarm  
Acknowledge Alarms  
Selects Sequence mode  
Iris close –  
Alarm Ack  
SEQ  
Alarm Ack  
SEQ  
3
Seq  
4
Iris –  
Iris C  
Iris O  
Store  
<-  
Frame <  
Frame >  
Stop  
4
Iris +  
Iris Open +  
5
Set  
Store a preset (preshot)  
6
Recycle (Undo)  
Undo previous camera selection  
(NetCPU)  
VCR F2  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
UltraKey Lite Controller Installation and User Guide  
Table 2-2  
VideoBloX Key Functions (cont’d)  
PCK (Cam Mode) PCK (Device Mode)  
ID  
7
Key Description  
Pause Play Rev  
Review  
Function in Camera Mode  
Selects previous camera  
Puts keyboard in Device mode  
Store a preset (preshot)  
Puts keyboard in Device mode  
Selects next camera  
Prev  
NA  
Stop  
Pause  
Rec  
8
9
Record  
Store  
NA  
10  
11  
12  
Search  
Index -  
Play  
Pause Play Fwd  
Tour  
Next  
NA  
Tour 1 Runs SEQ 250 on CPU  
Tour 2 Runs SEQ 251 on CPU  
Tour 3 Runs SEQ 252 on CPU  
Tour 4 Runs SEQ 253 on CPU  
13  
14  
15  
View  
Recall a preset (preshot)  
Selects Device mode  
Recall  
VCR  
NA  
Play  
VCR  
VCR  
MUX Screen  
MUX 1 Runs SEQ 245 on CPU  
MUX 2 Runs SEQ 246 on CPU  
MUX 3 Runs SEQ 247 on CPU  
MUX 4 Runs SEQ 248 on CPU  
Index +  
16  
17  
18  
19  
20  
22  
23  
23  
23  
23  
23  
23  
25  
25  
25  
25  
25  
25  
27  
Numeric Keys 0-9  
Enter  
Numeric Entry  
Numeric Keys 0-9 Numeric Keys 0-9  
Accept entry  
Enter  
Enter  
Clr  
Clear  
Clear previous entry  
Clr  
Monitor  
Selects Monitor mode  
Selects Camera mode  
Selects Alternate camera (NetCPU)  
Selects next camera  
MON  
MON  
CAM  
Camera  
CAM  
PTZ Call  
Enter  
Touch wheel right  
Touch wheel left  
Touch ring Up  
Touch ring Down  
Touch ring Left  
Touch ring Right  
Joystick Left  
Joystick Right  
Joystick Up  
Joystick Down  
Twist Zoom right  
Twist Zoom left  
Mon B  
Next  
Next  
Selects previous camera  
Nudges PTZ Up  
Prev  
Prev  
Up  
Up  
Nudges PTZ Down  
Down  
Down  
Nudges PTZ Left  
Left  
Left  
Nudges PTZ Right  
Right  
Right  
Move PTZ left variable speed  
Move PTZ right variable speed  
Move PTZ up variable speed  
Move PTZ down variable speed  
Zoom PTZ in variable speed  
Zoom PTZ out variable speed  
Joystick Left  
Joystick Right  
Joystick Up  
Joystick Down  
Twist Zoom right  
Twist Zoom left  
NA  
Joystick Left  
Joystick Right  
Joystick Up  
Joystick Down  
Twist Zoom right  
Twist Zoom left  
NA  
Depends on controller address. EG,  
Add 1 SEQ201 run, Add 2, SEQ202  
run, and so on.  
Document 800-07422 Rev A  
08/10  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the UltraKey Lite Controller  
Table 2-2  
Function in Camera Mode  
Depends on controller address. EG,  
VideoBloX Key Functions (cont’d)  
ID  
Key Description  
PCK (Cam Mode) PCK (Device Mode)  
28  
Mon A  
NA  
NA  
Add 1 SEQ201 run, Add 2, SEQ202  
run, and so on.  
29  
Login  
Login/Logout of CPU  
Login  
Login  
30  
F1  
F1: Define in CFG software  
F2: Define in CFG software  
F3: Define in CFG software  
F4: Define in CFG software  
F5: Define in CFG software  
F6: Define in CFG software  
F7: Define in CFG software  
F8: Define in CFG software  
F9: Define in CFG software  
F10: Define in CFG software  
Toggle Auxillary 1  
P
P
30  
F2  
BJ  
BJ  
30  
F3  
AR  
AR  
30  
F4  
PB  
PB  
30  
F5  
PTZ Slots  
PTZ Cas  
Door  
PTZ Slots  
PTZ Cas  
Door  
30  
F6  
30  
F7  
30  
F8  
Back House  
Hard Count  
Soft Count  
Aux 1  
Back House  
Hard Count  
Soft Count  
Index -  
Index +  
CntZero  
Cash Slots  
Cash Cage  
Group 13  
Group 14  
Group 15  
Group 16  
Memory  
Data  
30  
F9  
30  
F10  
21+1  
21+2  
21+3  
21+30  
21+30  
21+30  
21+30  
21+30  
21+30  
21+4  
21+5  
21+6  
21+7  
21+8  
21+F10  
21+F7  
21+F8  
21+F9  
24/26  
24/26  
ALT + 1  
ALT + 2  
ALT + 3  
ALT+F1  
ALT+F2  
ALT+F3  
ALT+F4  
ALT+F5  
ALT+F6  
ALT + 4  
ALT + 5  
ALT + 6  
ALT + 7  
ALT + 8  
ALT+F10  
ALT+F7  
ALT+F8  
ALT+F9  
Focus Near +  
Focus Far -  
Toggle Auxillary 2  
Aux 2  
Toggle Auxillary 3  
Aux 3  
F11: Define in CFG software  
F12: Define in CFG software  
F13: Define in CFG software  
F14: Define in CFG software  
F15: Define in CFG software  
F16: Define in CFG software  
Toggle Auxillary 4  
Cash Slots  
Cash Cage  
Group 13  
Group 14  
Group 15  
Group 16  
Aux 4  
Toggle Auxillary 5  
AutoPan  
PTZ F1  
PTZ F2  
PTZ F3  
User 4  
Toggle Auxillary 6  
VCR F1  
VCR F2  
VCR F3  
User 4  
Toggle Auxillary 7  
Toggle Auxillary 8  
RUN 4: Define in CFG software  
RUN 1: Define in CFG software  
RUN 2: Define in CFG software  
RUN 3: Define in CFG software  
Focus Near +  
User 1  
User 1  
User 2  
User 2  
User 3  
User 3  
Focus N  
Focus F  
Rew  
Focus Far -  
Fwd  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
UltraKey Lite Controller Installation and User Guide  
MAXPRO Key Functions  
Note  
Use Figure 2-1 to locate each key as labeled in the ID column.  
Table 2-3  
MAXPRO Key Functions  
ID  
Key Description  
Key Code  
4
Default MAX Function  
Alarm Clear  
Scan Select  
Iris Open  
UltraKey  
Halt  
2
Alarm  
3
Seq  
8
Group 2  
4
Iris +  
90  
Iris +  
4
Iris -  
91  
Iris Close  
Set  
Iris -  
5
Set  
26  
None  
6
Recycle (Undo)  
Pause Play Rev  
Review  
95  
Flashback  
VCR Rewind  
Text  
Tour  
7
80  
VCR Rewind  
Review  
8
85  
9
Record  
79  
Rec  
Rec  
10  
Search  
77  
Stop  
Stop  
11  
Pause Play Fwd  
Tour  
78  
Play  
Play  
12  
102  
74  
PTZ Aux  
Flashback  
View  
13  
View  
View  
14  
VCR  
60  
VCR  
None (Menu)  
Alternate  
Keypad key 1  
Keypad key 2  
Keypad key 3  
Keypad key 4  
Keypad key 5  
Keypad key 6  
Keypad key 7  
Keypad key 8  
Keypad key 9  
Keypad key 0  
Enter  
15  
MUX Screen  
Number 1  
Number 2  
Number 3  
Number 4  
Number 5  
Number 6  
Number 7  
Number 8  
Number 9  
Number 0  
Enter  
50  
Mux  
16-1  
16-2  
16-3  
16-4  
16-5  
16-6  
16-7  
16-8  
16-9  
16-0  
17  
62  
Keypad key 1  
Keypad key 2  
Keypad key 3  
Keypad key 4  
Keypad key 5  
Keypad key 6  
Keypad key 7  
Keypad key 8  
Keypad key 9  
Keypad key 0  
Enter  
63  
64  
66  
67  
68  
70  
71  
72  
75  
76  
Document 800-07422 Rev A  
08/10  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Using the UltraKey Lite Controller  
Table 2-3  
Key Description  
MAXPRO Key Functions (cont’d)  
ID  
Key Code  
Default MAX Function  
Pause  
UltraKey  
808  
18  
Clear  
808  
19  
Monitor  
61  
Monitor  
Camera  
Alt  
Monitor  
20  
Camera  
73  
Camera  
21  
Alt  
10  
Group 4  
PTZ Call  
Shuttle R  
Shuttle L  
Up Arrow  
Down Arrow  
Left Arrow  
Right Arrow  
22  
PTZ Call  
Touch wheel right  
Touch wheel left  
Touch ring Up  
Touch ring Down  
Touch ring Left  
Touch ring Right  
Joystick Left  
Joystick Right  
Joystick Up  
Joystick Down  
Twist Zoom right  
Twist Zoom left  
Mon B  
94  
Light  
23  
105 (1-8)  
None  
23  
106 (1-8)  
None  
23  
65  
69  
23  
25  
Up Arrow  
Down Arrow  
None  
23  
23  
23  
None  
25  
25  
25  
25  
25  
25  
27  
58  
57  
41  
30  
65  
1
F10  
Monitor B  
Monitor A  
None  
28  
Mon A  
F9  
29  
Login  
Active  
30  
F1  
Max Menu  
Up Arrow  
Full  
Group 12  
Up Arrow  
Alarm  
30  
F2  
30  
F3  
30  
F4  
2
2x2  
None  
30  
F5  
34  
6
None  
None  
30  
F6  
Left Arrow  
Down Arrow  
Right Arrow  
None  
None  
30  
F7  
69  
7
Down Arrow  
Group 1  
None  
30  
F8  
30  
F9  
35  
33  
100  
16  
17  
30  
F10+F1  
F10+F2  
F10+F3  
F10+F4  
None  
None  
21+1  
21+2  
21+3  
Scroll Up  
Insert  
Scroll Up  
None  
Delete  
Group 5  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
UltraKey Lite Controller Installation and User Guide  
Table 2-3  
Key Description  
MAXPRO Key Functions (cont’d)  
ID  
Key Code  
Default MAX Function  
Pause  
UltraKey  
Group 6  
21+30  
21+30  
21+30  
21+30  
21+30  
24/26  
24/26  
F10+F5  
F10+F6  
F10+F7  
F10+F8  
F10+F9  
Focus +  
Focus -  
18  
53  
101  
54  
28  
89  
88  
None  
Print Select  
Scroll Down  
Freeze  
Scroll Down  
F6  
Scan Halt  
Focus Near  
Focus Far  
Group 10  
Focus +  
Focus -  
Document 800-07422 Rev A  
08/10  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the UltraKey Lite Controller  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3
Installing UltraKey Lite with VideoBloX  
In this section:  
•
•
•
•
Navigating the LCD Configuration Menus, page 31  
Installing and Configuring a Serial Connection, page 32  
Installing and Configuring an Ethernet Connection, page 36  
(Optional) Configuring UltraKey Lite Using the Web Browser, page 41  
Note  
For all installations, refer to the applicable VideoBloX or VideoBloX Lite  
installation or user guides for more information.  
This section explains how to connect the UltraKey Lite controller to VideoBloX and how  
to enter the basic configuration settings specific to VideoBloX. UltraKey Lite can control  
the remote VideoBloX via either the serial port or the Ethernet.  
Navigating the LCD Configuration Menus  
Note  
The use of the arrow keys under the LCD is used for the following instructions.  
See Figure 3-1. Also see Using the UltraKey Lite to Navigate the LCD Menus  
on page 22 for detailed instructions for other ways to navigate or System  
Administration Using the Controller LCD on page 65 for a configuration menu  
tree.  
Document 800-07422 Rev A  
08/10  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Installing UltraKey Lite with VideoBloX  
Figure 3-1  
LCD and LCD Navigation Keys  
Numeric  
keypad and  
Ent key  
Left  
arrow  
key  
Up  
arrow  
key  
Down  
arrow  
key  
Right  
arrow  
key  
Figure 3-2  
VideoBloX LCD Configuration Menu Tree  
Mode Selection:  
VideoBloX  
Connection  
Configuration  
Set Up  
Serial Port  
Ethernet  
Address  
[1 to 32]  
IP Address  
Baud Rate  
Control Mode  
159.099.251.230  
Ethernet  
Serial Port  
Installing and Configuring a Serial Connection  
Step 1: Connect to the UltraKey Lite Using the Serial Port  
Note  
Use only COM1 when in VideoBloX mode. See Table 3-1 below.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
UltraKey Lite Controller Installation and User Guide  
Table 3-1  
Serial Port COM1 and COM2 Pin Assignments  
Serial Port  
Type  
Pin  
1
Signal  
RX +  
RX –  
COM1  
RS422  
2
5
GND  
TX –  
7
8
TX +  
T/R –  
T/R +  
RS485  
7
8
Note  
For a list of accessories see Shipping Checklist on page 18 and for port  
connections see UltraKey Lite Port Connections and Descriptions on page 19.  
1. Select the applicable adapter plug and insert it into the AC adapter. Push to click it  
into place. See Figure 3-3.  
2. Plug the AC adapter into the controller power port and the adapter into a power  
source.  
3. Connect an RJ45 network cable to the controller serial port.  
4. Connect the RJ45 network cable to VideoBloX:  
•
For backwards compatibility with VideoBloX and VideoBloX Lite CPUs, an RJ45  
to DB9 male adapter is required and included with your shipment. See Figure 3-4.  
•
For VideoBloX NetCPU, the installation is a direct connection with the RJ45  
network cable, also included. See Figure 3-5 and Figure 3-6.  
Figure 3-3  
AC Power Adapter with CEE 7/16 Europlug  
Slideplugontothe  
adapter and snap  
into place  
Document 800-07422 Rev A  
08/10  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Installing UltraKey Lite with VideoBloX  
Figure 3-4  
RJ45 to DB9 Male Adapter for VideoBloX and VideoBloX Lite CPUs  
Controller  
Serial Port  
RJ45 to DB9  
male adapter  
VideoBloX  
RJ45 network cable  
Figure 3-5  
Direct RJ45 Serial Port Connection for VideoBloX NetCPUs  
Controller  
VideoBloX  
Serial Port  
RJ45 network cable  
Figure 3-6  
VideoBloX Serial Port RS422 Connection Example  
VB master:  
VideoBloX Serial Port (RS422)  
1--RS422_TX –  
2--RS422_TX +  
3--RS422_RX +  
4--RS422_RX –  
5--GND  
VIdeoBlox Master  
Connections  
RJ45 to  
DB9 Male  
RJ45 to  
DB9 Male  
5
5
RJ45 define:  
1--RS485_2+/RS422_2_TX+/  
RS422_1_RX+  
PI NOUT  
5
TX+  
TX- GND RX-  
RX+  
2--RS485_2-/RS422_2_TX-/  
RS422_1_RX-  
3—NC  
4--RS232RX  
5--RS232GND  
RJ45  
#1  
#2  
#2  
#1  
#5  
#5  
#7  
#4  
#8  
#3  
DB9  
1
RJ45  
Network  
Cable  
1
RJ45  
Network  
Cable  
6--RS232TX  
7--RS485_1-/RS422_1_TX-  
8--RS485_1+/RS422_1_TX+  
*RS485_2/RS422_2_TX and  
RS232 use same UART_AC  
PSU  
3
PSU  
3
Controller 32  
Controller 1  
Step 2: Configure the Controller for VideoBloX Mode  
Note  
The controller factory defaults are VideoBloX mode, Address 1, baud rate  
19200 bps. If any other mode has been selected then use the following steps  
to select VideoBloX mode. Otherwise skip to Step 3: Configure Address, Baud  
Rate or IP for VideoBloX Mode, page 35.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
UltraKey Lite Controller Installation and User Guide  
1. If not already done, install and connect the controller to a power source.  
2. From the home screen, press Alt > Clr to enter the System Configuration: System  
Set menu.  
3. Enter the PIN password 3434.  
The System Set: Mode screen displays.  
4. Press the LCD right arrow key to enter the Mode Selection menu.  
5. Scroll to and select VideoBloX. Press Ent.  
Step 3: Configure Address, Baud Rate or IP for VideoBloX Mode  
1. Press Alt > Clr. If prompted, enter the password 3434to enter the System Set top  
menu.  
2. Press the LCD down arrow to scroll to the System Set:  
System Set:  
Config menu.  
CONFIG  
3. Press the right arrow key to enter the Configuration menus.  
4. Press the LCD up/down arrow keys to scroll through the options (restore default, VB  
settings, maxpro settings, network, language, back light, slider update, hardware test,  
about).  
5. Scroll to the Configuration: VB Settings menu, then press  
Configuration  
Ent.  
VB Settings  
6. Press the LCD right arrow key to scroll to enter the VB  
Set Up  
Settings menu.  
Address 4  
7. Press the right arrow key to scroll through the Set Up menu  
Control Mode:  
to the Control Mode submenu. The current setting is  
displayed (Serial Port or Ethernet).  
Serial Port  
8. Press the up/down arrow keys to scroll to Serial Port then press Ent.  
9. Press the LCD right arrow key to scroll to Set Up: Address.  
10. Use the LCD up/down arrow keys to scroll to an address between 1 and 32 to assign  
to the controller. You can also use the numeric keypad to enter a number between 1  
and 32. However, if you enter a number greater than 32, the message Invalid ID  
displays on the LCD.  
11. Press Ent.  
12. Press the LCD right arrow key to scroll to Set Up: Baud Rate.  
13. Press the LCD up/down arrow keys to select a baud rate. 1200 bps, 9600, 19.2 KB  
(default for VideoBloX) or 57.6 KB bps are available for VideoBloX.  
14. Press Ent.  
15. If you are using the TCP/IP to connect to a VideoBloX  
Set Up  
NetCPU, then press the LCD right arrow key to scroll to Set  
Up: IP Address. Press Ent.  
IP Address  
Document 800-07422 Rev A  
08/10  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Installing UltraKey Lite with VideoBloX  
Note  
In this field, you are setting the VideoBloX NetCPU IP address. To set the  
UltraKey Lite IP address or enter the main configuration menus, press Alt >  
Clr and see Step 3: Set and Configure for an Ethernet Connection on page 38.  
16. Use the numeric keypad to enter an IP address as required,  
IP Address  
then press Ent.  
159.099.251.230  
Step 4: Configure VideoBloX Mode Default Settings While Powering Up  
1. While powering up, when the Time Left 3 menu displays, press Alt > Camera to set  
the VideoBlox mode.  
2. Set the corresponding serial port as:  
Time Left 3  
Baud Rate: 19.2 KB  
Data Bit: 8  
Parity: None  
Stop Bit: 1  
Installing and Configuring an Ethernet Connection  
For a list of accessories see Shipping Checklist on page 18 and for port connections and  
pin assignments see UltraKey Lite Port Connections and Descriptions on page 19. The  
UltraKey Lite Controller runs TCP/IP keyboard protocol.  
Step 1: Connect to the UltraKey Lite Ethernet Port  
Note  
The direct RJ45 connection using the Ethernet port is only available with  
newer model VideoBloX NetCPU systems.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
UltraKey Lite Controller Installation and User Guide  
Table 3-2  
RJ45 Ethernet Pin Assignments  
Port  
Pin  
1
Signal  
TX +  
TX –  
RJ45 Ethernet  
2
3
RX+  
RX –  
6
1. Select the applicable adapter plug and insert it into the AC adapter. Push to click it  
into place. See Figure 3-3.  
2. Plug the AC adapter into the controller power port and the adapter into a power  
source.  
3. Plug an RJ45 network cable from the network to the controller Ethernet port. Up to 32  
controllers can be connected to the network. See Figure 3-7.  
4. Connect VideoBloX to the network. Refer to the applicable VideoBloX Installation  
Guide for instructions.  
Figure 3-7  
Ethernet Port Connections to VideoBloX  
Ethernet Port  
VideoBloX  
TCP/IP  
Controller 1  
RJ45 network cables  
Network  
Controller 32  
TCP/IP  
Ethernet Port  
Step 2: Configure the Controller for VideoBloX Mode  
Note  
The controller factory defaults are VideoBloX mode, Address 1, baud rate  
19200 bps. If any other mode has been selected then see Step 2: Configure  
the Controller for VideoBloX Mode on page 34 to select VideoBloX mode.  
Otherwise skip to the next step.  
Document 800-07422 Rev A  
08/10  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Installing UltraKey Lite with VideoBloX  
Step 3: Set and Configure for an Ethernet Connection  
1. Press Alt > Clr. If prompted, enter the password 3434to enter the System Set top  
menu.  
2. Press the LCD down arrow to scroll to the System Set:  
Config menu.  
System Set:  
CONFIG  
3. Press the right arrow key to enter the Configuration menus.  
4. Press the LCD up/down arrow keys to scroll through the options (restore default, VB  
settings, maxpro settings, network, language, back light, slider update, hardware test,  
about).  
5. Scroll to the Configuration: VB settings menu, then press  
Configuration  
Ent.  
VB Settings  
6. Press the right arrow key to enter the Set Up menu.  
Set Up  
7. Press the right arrow key to scroll through the Set Up menu  
to the Control Mode submenu. The current setting is  
displayed (Serial Port or Ethernet).  
Address 4  
8. Press the LCD up/down arrow keys to scroll to Ethernet.  
Control Mode:  
Ethernet  
9. Press Ent.  
The Set Up: IP Address menu displays.  
10. Press Ent.  
Note  
In this field, you are setting the VideoBloX NetCPU IP address. To set the  
UltraKey Lite IP address or enter the main configuration menus, press Alt >  
Clr.  
11. Use the numeric keypad to enter an IP address as required,  
IP Address  
then press Ent.  
159.099.251.230  
12. Press the LCD right arrow key to scroll to Set Up: Address.  
13. Use the LCD up/down arrow keys to scroll to an address between 1 and 32 to assign  
to the controller. You can also use the numeric keypad to enter a number between 1  
and 32. However, if you enter a number greater than 32, the message Invalid ID  
displays on the LCD.  
14. Press Ent.  
Step 4: Configure the Controller for an Ethernet Connection  
1. Press Alt > Clr to exit from the VideoBloX configuration menu.  
2. Press Alt > Clr a second time to enter the System Set top menu.  
3. Press the LCD down arrow key to scroll to the System Set:  
System Set:  
Config menu.  
CONFIG  
4. Press the right arrow key to enter the Configuration menus.  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
UltraKey Lite Controller Installation and User Guide  
5. Press the LCD up/down arrow keys to scroll through the options (serial port, network,  
language, back light, slider update, cascade linkage, hardware test, about).  
6. Scroll to the Configuration: Network menu, then press  
Configuration  
Ent.  
Network  
7. There are three sub-menus in this menu (Show Net Infor,  
DHCP, and Manual Settings). The structure is as follows:  
Network:  
Network  
DHCP  
DHCP  
Network:  
Show Net Infor  
Network:  
Show Net Infor  
Manual Setting  
Manual Setting  
Show Net Infor Menu  
The Show Net Infor Menu displays the Network information, including IP Address, DNS,  
Gateway, and Netmask.  
Automatically Configuring the Network Using DHCP  
The Dynamic Host Configuration Protocol (DHCP) is a computer networking protocol used  
by devices (DHCP clients) to obtain configuration information for operation in an Internet  
Protocol network. It is used to configure the network automatically.  
Automatically configuring the network using the DHCP menu:  
1. Press the LCD down arrow to scroll to the Network: DHCP  
Network:  
menu.  
DHCP  
2. Press Ent and the keyboard's network will be configured  
Please wait....  
automatically.  
•
•
If the network configuration is successfull, then a  
Succeeded! message displays.  
Succeeded!  
Failed!  
If the network configuration was not successful, then a  
Failed!message displays.  
When the nework configures successfully, the user can enter the  
Show Net Infor menu to see the IP Address, IP Address, DNS,  
Gateway and Netmask.  
Network:  
Manual Setting  
Manually Configuring the Network  
Manually configuring the network using the Manual Setting menu:  
1. Press the LCD down arrow key to scroll to the Network: Manual Setting menu  
Document 800-07422 Rev A  
08/10  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing UltraKey Lite with VideoBloX  
2. When you are at the Network: Manual Setting menu, press Ent, then press the LCD  
up/down arrow keys to set the UltraKeyLite network parameters (IP address, gateway,  
netmask and DNS).  
3. Press the LCD up/down arrow keys to scroll through the  
Network:  
menu options to select IP Address, then press Ent to  
select.  
IP Address  
a. Using the numeric key pad, enter an IP address, then  
IP Address  
press Ent to save.  
The LCD menu displays the message: IPAddr  
159.099.251.230  
Changed.  
b. Press the up/down arrow keys to select Yes to save or  
IP Addr Changed  
No to cancel, then press Ent.  
Yes  
Note  
In this field, you are setting the UltraKey Lite IP address. To set the VideoBloX  
IP address (for communication purposes), see Step 3: Set and Configure for  
an Ethernet Connection.  
4. Press the LCD up/down arrow keys to scroll through the menu options and select  
Gateway. Press Ent.  
a. Using the number keys, enter a Gateway as required, then press Ent to save.  
The LCD menu displays the message: GW Changed.  
b. Press the up/down arrow keys to select Yes to save or No to cancel, then press  
Ent.  
5. Press the LCD up/down arrow keys to scroll through the menu options and select  
NetMask. Press Ent.  
a. Using the number keys, enter a NetMask as required, then press Ent to save.  
The LCD menu displays the message: NetMsk Changed.  
b. Press the up/down arrow keys to select Yes to save or No to cancel, then press  
Ent.  
6. Press the LCD up/down arrow keys to scroll through the menu options and select  
DNS. Press Ent.  
a. Using the number keys, enter a DNS as required, then press Ent to save.  
The LCD menu displays the message: DNS Changed.  
b. Press the up/down arrow keys to select Yes to save or No to cancel, then press  
Ent to save.  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
UltraKey Lite Controller Installation and User Guide  
Step 5: Setting the Keyboard Address While Powering Up  
While powering up, when the Time Left 3 menu displays, press certain keys (see Table 3-3)  
to set the keyboard address.  
Table 3-3  
Setting the Keyboard Address  
Key  
Address  
Key  
Address  
11  
Alt > 1  
Alt > 2  
Alt > 3  
Alt > 4  
Alt > 5  
Alt > 6  
Alt > 7  
Alt > 8  
Alt > 9  
Alt > 0  
1
2
3
4
5
6
7
8
9
10  
Alt > F1  
Alt > F2  
Alt > F3  
Alt > F4  
Alt > F5  
Alt > F6  
Alt > F7  
Alt > F8  
Alt > F9  
12  
13  
14  
15  
16  
17  
18  
19  
Alt > F10 20  
(Optional) Configuring UltraKey Lite Using the Web Browser  
Logging into the Web Browser  
1. If not already done, navigate to, or copy and paste, the applicable IP address into  
your web browser:  
•
•
LAN connections: for example, http://192.168.1.9  
Crossover cable connections: for example, http://192.168.1.9 (default)  
2. In the User Name field enter Administrator (case sensitive).  
3. In the Password field enter 1234 (default).  
4. Click Login.  
Document 800-07422 Rev A  
08/10  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Installing UltraKey Lite with VideoBloX  
Figure 3-8  
UltraKey Lite Login Page  
Step 1: Configure UltraKey Lite to VideoBloX Mode  
1. Log into the web browser.  
2. From the top menu, click the Configuration tab. See Figure 3-9.  
3. From the side menu, click the System Configurations tab.  
4. From the System Mode drop down list, select VideoBlox.  
5. From the System Language drop down list, select English or French.  
6. From the Background Light drop down list select ON or OFF.  
7. Click Apply to save the configuration, Cancel to exit without saving or Default to  
restore all factory default values.  
Figure 3-9  
System Configuration Tab  
Step 2: Configure VideoBloX Network Settings  
1. From the side menu, click VideoBloX Configuration. See Figure 3-10.  
2. Under Keyboard ID Setting, enter a number between 1 and 32 to set the controller  
ID.  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
UltraKey Lite Controller Installation and User Guide  
Note  
By default, addresses 1– 5 in the VideoBloX NetCPU are set for serial  
connection. Please change this in the NetCPU configuration if you want to  
use addresses 1– 5 for Ethernet connection.  
3. Under VB Device Network Setting, enter the IP address and Port Number of the  
VideoBloX system.  
4. Click Apply to save the configuration, Cancel to exit without saving, or Default to  
restore all factory default values.  
5. Go to either Step 3A or 3B to configure the system for Serial or Ethernet connections  
respectively.  
Figure 3-10  
VideoBloX Configuration Tab  
Checking the Network Connection Using the Ping Function  
After the IP address is entered and applied, press the Ping button.  
•
•
A green Ping button indicates the device at this IP address has replied to the ping.  
A red Ping button indicates the device at the IP address did not reply. Please check  
that the IP address is correct and that there is a valid network path between the two IP  
addresses.  
Step 3A: Configure the Controller for a Serial Port Connection  
1. From the side menu, click Serial Port Configuration. See Figure 3-11.  
Document 800-07422 Rev A  
08/10  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Installing UltraKey Lite with VideoBloX  
2. Under Serial Port1 Settings, select the following from each drop-down list as  
required:  
•
Baud Rate: 1200, 9600, 19200 or 57600 bps.  
The default for VideoBloX is 19200.  
•
•
•
•
Parity: none  
Stop Bits: 1 bit  
Data Bits: 8 bits  
Serial Mode: RS422  
3. Click Apply to save the configuration, Cancel to exit without saving, or Default to  
restore all factory default values.  
Figure 3-11  
Serial Port Configuration Tab  
Step 3B: Configure the Controller for an Ethernet Connection  
1. From the side menu, click IP Configuration. See Figure 3-12.  
2. In each of the fields, enter IP address, subnet mask, gateway and DNS values.  
3. Click Apply to save the configuration, Cancel to exit without saving, or Default to  
restore all factory default values.  
Figure 3-12  
IP Configuration Tab  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
UltraKey Lite Controller Installation and User Guide  
Step 4: Configuring the Dynamic Keys  
You can configure the hard keys on the web server.  
1. From the side menu, click DynKey Configuration.  
Figure 3-13  
DynKey Configuration Tab  
2. In the drop-down menu, select the key you want to configure.  
3. In the right column, select the function you want to add to the hard key, then click  
Add.  
That selected function appears in the center column.  
4. Repeat step 3 to add another function to the selected hard key.  
5. Click Apply to save.  
Note  
Note  
No more than 10 functions can be configured to a hard key.  
Neither the number key (#) nor the Logon key can be configured.  
Document 800-07422 Rev A  
08/10  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Installing UltraKey Lite with VideoBloX  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
Installing UltraKey Lite with MAXPRO-Net  
In this section:  
•
•
•
•
Navigating the LCD Configuration Menus, page 47  
Installing and Configuring a Serial Connection, page 49  
Installing and Configuring an Ethernet Connection, page 56  
(Optional) Configuring UltraKey Lite Using the Web Browser, page 60  
Note  
For all installations, refer to the applicable MAXPRO-Net installation or user  
guides for more information.  
This section explains how to connect the UltraKey Lite controller to MAXPRO-Net and how  
to enter the basic configuration settings specific to MAXPRO-Net. For other user  
configurations see the index or table of contents.  
Navigating the LCD Configuration Menus  
Note  
The use of the arrow keys under the LCD is used for the following instructions.  
See Figure 4-1. Also see Using the UltraKey Lite to Navigate the LCD Menus  
on page 22 for detailed instructions for other ways to navigate or System  
Administration Using the Controller LCD on page 65 for a configuration menu  
tree.  
Document 800-07422 Rev A  
08/10  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Installing UltraKey Lite with MAXPRO-Net  
Figure 4-1  
LCD and Navigation Keys  
Numeric  
keypad and  
Ent key  
Left  
arrow  
key  
Up  
arrow  
key  
Down  
arrow  
key  
Right  
arrow  
key  
Figure 4-2  
MAXPRO LCD Menu Tree  
Mode Selection:  
MAXPRO  
Connection  
Configuration  
Maxpro Key Code  
Maxpro offline  
keyboard 1  
Fixed Camera  
Camera 1  
By Serial Port  
By Ethernet  
RS232 directly  
RS422 indirectly  
Maxpro Setting  
Keyboard ID  
1 to 32  
Baud Rate  
Joystick Speed  
Normal / High  
Server IP  
Serial Port  
26024  
Serial Port Mode  
RS232 / RS485  
9600 / 19200 bps  
_59/099.251.132  
From the MAXPRO settings menu, you set the following based on either a Serial or Ethernet  
connection:  
•
•
•
•
•
•
Keyboard ID (address) - Serial or Ethernet connections  
Baud rate - Serial connections only  
Joystick speed - Serial or Ethernet connections  
Server IP - Ethernet connections only  
Server Port - Ethernet connections only  
Serial port mode - Serial connections only  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
UltraKey Lite Controller Installation and User Guide  
Installing and Configuring a Serial Connection  
Step 1: Connect to the UltraKey Lite Serial Port  
Note  
For a list of accessories see Shipping Checklist on page 18 and for port  
connections see UltraKey Lite Port Connections and Descriptions on page 19.  
Note  
COM1 (RS422) and COM2 (RS485) are configured using the controller LCD  
menu and cannot be used at the same time. See Table 4-1 below.  
Table 4-1  
Serial Port COM1 and COM2 Pin Assignments  
Serial Port  
Type  
Pin  
1
Signal  
RX +  
RX –  
GND  
TX –  
COM1  
RS422  
2
5
7
8
TX +  
T/R –  
T/R +  
RXD  
RS485  
RS232  
7
8
COM2  
4
5
GND  
TXD  
6
RS485  
1
T/R +  
T/R –  
2
Document 800-07422 Rev A  
08/10  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Installing UltraKey Lite with MAXPRO-Net  
Figure 4-3  
RS232 Serial Port Connection  
MAXPRO Serial Port (RS232)  
RJ45 to  
DB9 female  
4
RJ45 to  
4
DB9 female  
RJ45 to DB9 female  
4
RJ45 define:  
1--RS485_2+/RS422_2_TX+/  
RS422_1_RX+  
2--RS485_2-/RS422_2_TX-/  
RS422_1_RX-  
3—NC  
RJ45 (Ultrakey Lite)  
DB9(Maxpro)  
#4(RX)  
#3(TX)  
#5(GND) #6(TX)  
#5(GND) #2(RX)  
4--RS232RX  
5--RS232GND  
6--RS232TX  
7--RS485_1-/RS422_1_TX-  
8--RS485_1+/RS422_1_TX+  
*RS485_2/RS422_2_TX and  
RS232 use same UART_AC  
1
RJ45  
Network  
Cable  
1
RJ45  
Network  
Cable  
PSU  
3
PSU  
3
Controller 16  
Controller 1  
Figure 4-4  
RS232 Serial Port Connection and MegaPIT  
MAXPRO Serial Port (RS232) and MegaPIT  
MEGAPIT  
1--RS422_TX+  
2--RS422_TX-  
3--NC  
4--RS232TX  
5--RS232GND  
6--RS232RX  
7--RS422_RX-  
8--RS422_RX+  
RS232  
MEGAPIT - 32  
MEGAPIT - 1  
RJ45 define:  
1--RS485_2+/RS422_2_TX+/  
RS422_1_RX+  
2--RS485_2-/RS422_2_TX-/  
RS422_1_RX-  
1
3—NC  
4--RS232RX  
5--RS232GND  
RJ45  
Network  
Cable  
RS232  
6--RS232TX  
7--RS485_1-/RS422_1_TX-  
8--RS485_1+/RS422_1_TX+  
*RS485_2/RS422_2_TX and  
RS232 use same UART_AC  
PSU  
3
Controller 8  
Controller 249  
Controller 256  
PSU  
3
Controller 1  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
UltraKey Lite Controller Installation and User Guide  
Figure 4-5  
RS232 Serial Port Connection and MX18  
MAXPRO Serial Port (RS232) and MX18  
RJ45 define:  
1--RS485_2+/RS422_2_TX+/  
RS422_1_RX+  
2--RS485_2-/RS422_2_TX-/  
RS422_1_RX-  
MX18  
3—NC  
4--RS232RX  
5--RS232GND  
6--RS232TX  
7--RS485_1-/RS422_1_TX-  
8--RS485_1+/RS422_1_TX+  
*RS485_2/RS422_2_TX and  
RS232 use same UART_AC  
7
7
RJ11 Flat  
Ribbon  
RJ11 Flat  
Ribbon  
Cable -  
Cable -  
straight  
straight  
PSU  
3
PSU  
3
Controller 8  
Controller 1  
RS232 Connections with an RJ45 to DB9 Female Adapter  
1. Select the applicable adapter plug and insert it into the AC adapter. Push to click it  
into place. See Figure 4-6.  
Figure 4-6  
AC Power Adapter with CEE 7/16 Europlug  
Slideplugontothe  
adapter and snap  
into place  
2. Plug the AC adapter into the controller power port and the adapter into a power  
source.  
3. Connect an RJ45 network cable to the controller serial port.  
4. Connect the RJ45 network cable to MAXPRO-Net. For RS232 backwards compatibility  
with MAXPRO-Net CPUs, plug the RJ45 to DB9 female adapter included with your  
shipment into the applicable port of MAXPRO-Net. See Figure 4-7.  
Figure 4-7  
RJ45 to DB9 Female Adapter (RS232)  
Serial Port (RS232)  
RJ45 to DB9  
female adapter  
MAXPRO-Net  
RJ45 network cable  
Document 800-07422 Rev A  
08/10  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Installing UltraKey Lite with MAXPRO-Net  
RS422 Connections Using a Converter and the Terminal Box  
1. Select the applicable adapter plug and insert it into the AC adapter. Push to click it  
into place. See Figure 4-6.  
2. Connect an RJ45 network cable from the RJ45 port on the terminal box to the  
controller serial port.  
3. Connect an RS422 cable from the RS422 terminal plug pins on the terminal box to an  
RS422 to RS232 converter (supplied by the installer or customer).  
4. Connect the RS422 to RS232 converter to the MAXPRO-Net RS232 port. See  
Figure 4-8.  
Figure 4-8  
RS422 to RS232 Converter Using the Terminal Box (RS422)  
Controller  
MAXPRO-Net  
RS232  
Terminal Box  
Serial Port (RS422)  
Ethernet Port  
RJ45 network cable  
RS422 to RS232  
converter  
RS422 COM1  
Table 4-2  
Terminal Box COM1 and COM2 Pin Assignments  
Location  
Serial Port  
Type  
Pin  
2
Signal  
TXD  
DB9 Port  
COM2  
RS232  
3
RXD  
GND  
TX+  
TX –  
RX+  
RX –  
GND  
TX+  
TX –  
GND  
TXD  
5
Terminal Plug  
COM1  
RS422  
1
2
3
4
5
RS485  
RS232  
1
2
COM2  
6
7
8
RXD  
RX+  
RX –  
RS485  
3
4
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
UltraKey Lite Controller Installation and User Guide  
Figure 4-9  
RS232 Serial Port Connection and Terminal Box RS422  
MAXPRO Serial Port (RS232) and Terminal Box (RS422)  
RS232  
RS232  
RS232  
to  
RS232  
to  
RS422  
RS422  
PL1  
RS422  
1--RS485_1+/RS422_1_TX+  
2--RS485_1-/RS422_1_TX-  
3--RS485_2+/RS422_2_TX+  
/RS422_1_RX+  
4--RS485_2-/RS422_2_TX-  
/RS422_1_RX-  
RS422  
DB9 male  
PL2  
DB9 male  
PL2  
PL1  
PL1  
Terminal Box  
2
2
5--RS232RX  
6--RS232TX  
RJ45  
RJ45  
7--RS232GND  
8--RS232GND  
*RS485_2/RS422_2_TX and  
RS232 use same UART_AC  
1
RJ45  
Network  
Cable  
1
RJ45  
Network  
Cable  
PSU  
3
PSU  
3
Controller 16  
Controller 1  
Figure 4-10  
RS232 Serial Port Connection, MX18 and the Terminal Box  
MAXPRO Serial Port (RS232), MX18 and Terminal Box  
PL1  
1--RS485_1+/RS422_1_TX+  
2--RS485_1-/RS422_1_TX-  
3--RS485_2+/RS422_2_TX+  
/RS422_1_RX+  
4--RS485_2-/RS422_2_TX-  
/RS422_1_RX-  
5--GND  
6--GND  
MX18  
7--RS232TX  
8--RS232RX  
*RS485_2/RS422_2_TX and  
RS232 use same UART_AC  
Terminal Box  
DB9 male  
PL2  
DB9 male  
PL2  
PL1  
PL1  
2
2
RJ45  
RJ45  
Terminal Box  
1
RJ45  
Network  
Cable  
1
RJ45  
Network  
Cable  
PSU  
3
PSU  
3
Controller 8  
Controller 1  
Document 800-07422 Rev A  
08/10  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Installing UltraKey Lite with MAXPRO-Net  
Step 2: Configure the Controller for MAXPRO Mode  
Note  
The controller factory defaults to VideoBloX mode, Address 1, baud rate  
19200 bps.  
1. If not already done, install and connect the controller to a power source.  
The UltraKey Lite LCD displays.  
2. From the home screen, press Alt > Clr to enter the System Configuration: System  
Set menu.  
3. Enter the PIN password 3434.  
The System Set: Mode screen displays.  
4. Press the LCD right arrow key to enter the Mode Selection menu.  
5. Scroll to and select MAXPRO. Press Ent.  
6. From the home screen, press Alt > Clr to enter the System Configuration: System  
Set menu.  
The System Set: Mode screen displays.  
7. Press the LCD right arrow key to enter the Mode Selection menu.  
8. Scroll to and select MAXPRO. Press Ent. MAXPRO  
Maxpro Loading.  
Loadingdisplays and one of two screens display:  
•
If the controller is able to connect to the MAXPRO  
network, the LCD displays the connection, for example,  
fixed camera 1has sent a signal from MAXPRO to  
the controller.  
FIXED CAMERA  
Camera 1  
•
If the controller is not able to connect to the MAXPRO  
network, the offline menu displays If this menu  
displays, you cannot configure the serial or ethernet  
connections in the next step.  
Maxpro offline  
Keyboard 1  
Step 3: Configure Address, Baud Rate, or IP for MAXPRO-Net mode  
1. Press Alt > Clr. If prompted, enter the password 3434 to  
System Set:  
enter the System Setup: Config menu.  
CONFIG  
2. Press the right LCD arrow key to enter the Configuration  
menus.  
3. Press the LCD up/down arrow keys to scroll through the  
Configuration  
options (restore default, VB settings, maxpro settings,  
network, language, back light, slider update, hardware test,  
Maxpro Settings  
about).  
Scroll to the Configuration: Maxpro settings menu, then press Ent.  
4. Select By Serial Port from the MAXPRO connection submenu, then press Ent.  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
UltraKey Lite Controller Installation and User Guide  
Note  
If the controller cannot connect to the MAXPRO network, then this step  
cannot be completed until the connection is established. However, the  
MAXPRO settings menu can be configured even if the controller has not  
connected to the MAXPRO network; that is, the LCD displays that MAXPRO is  
offline.  
5. Use the LCD up/down arrow keys to select RS232 or RS422, then press Ent.  
6. Use the LCD up/down arrow keys to scroll to an address between 1 and 99 to assign  
to the controller, then press Ent to save.  
7. Press the down LCD arrow key to scroll to Baud Rate. Press Ent and use the  
up/down arrow keys to select a baud rate of 9600 bps or 19200 bps for the controller.  
Press Ent to save.  
Note  
19200 bps is the default baud rate for most MAXPRO systems.  
8. Press the down LCD arrow key to scroll to Joystick Speed. Press Ent and use the  
up/down arrow keys to select Normal or High. Press Ent to save.  
9. Press the down LCD arrow key to scroll to Serial Port  
Maxpro Settings  
Mode. Press Ent and use the up/down arrow keys to select  
RS232 or RS422. Press Ent to save.  
SerialPortMode:  
Note  
In the following fields, you are setting the MAXPRO-Net Server IP address and  
port number. To set the UltraKey Lite IP address or enter the main  
configuration menus, press Alt > Clr.  
10. Press the down LCD arrow key to scroll to Server IP. Press  
Ent and use the up/down arrow keys or the numeric keys to  
enter the Server IP address. Press Ent to save.  
Maxpro Settings  
Server IP:  
11. Press the down LCD arrow key to scroll to Server Port.  
Press Ent and use the up/down arrow keys or the numeric  
keys to enter the Server Port Address. Press Ent to save.  
MaxproServer IP  
_59.099.251.132  
12. After the MAXPRO settings are complete, press Alt > Clr to  
Maxpro Settings  
Server Port:  
exit the Setup menu.  
Step 4: Configure MAXPRO Mode Default Settings While Powering Up  
1. While powering up, when the Time Left 3 menu displays,  
Time Left 3  
press Alt > Monitor to set the Maxpro mode.  
2. Set the corresponding serial port as:  
Document 800-07422 Rev A  
08/10  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing UltraKey Lite with MAXPRO-Net  
Baud Rate: 19.2 KB  
Data Bit: 7  
Parity: Even  
Stop Bit: 1  
Installing and Configuring an Ethernet Connection  
Step 1: Connect to the UltraKey Lite Ethernet Port  
Table 4-3  
Port  
RJ45 Ethernet Pin Assignments  
Pin  
1
Signal  
TX +  
TX –  
RJ45  
Ethernet  
2
3
RX+  
RX –  
6
1. Plug an RJ45 network cable from the network to the controller Ethernet port. Up to 99  
controllers can be connected to the network. See Figure 4-11.  
2. Connect MAXPRO-Net to the network. Refer to the applicable MAXPRO-Net  
Installation Guide for instructions.  
Figure 4-11  
Ethernet Port Connections to MAXPRO-Net  
Ethernet Port  
MAXPRO-Net  
TCP/IP  
TCP/IP  
Controller 1  
RJ45 Network cables  
Network  
TCP/IP  
Controller 32  
Ethernet Port  
56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
UltraKey Lite Controller Installation and User Guide  
Step 2: Configure the Controller for MAXPRO Mode  
Note  
The controller factory defaults to VideoBloX mode, Address 1, baud rate  
19200 bps. Follow the same steps as with the serial connection, Step 2:  
Configure the Controller for MAXPRO Mode on page 54.  
Step 3: Set and Configure for an Ethernet Connection  
1. From the MAXPRO connection submenu, select Ethernet.  
Note  
If the controller cannot connect to the MAXPRO network, then this first step  
cannot be completed until the connection is established. However, the  
MAXPRO settings menu can be configured even if the controller has not  
connected to the MAXPRO network; that is, the LCD displays that MAXPRO is  
offline.  
2. Press the LCD center key.  
Maxpro Settings  
Keyboard ID:  
The Maxpro Settings: Keyboard ID menu opens.  
3. Press Ent.  
4. Use the LCD up/down arrow keys to scroll to an address between 1 and 99 to assign  
to the controller.  
5. Press Ent to save.  
6. Press the down LCD arrow key to scroll to Joystick Speed. Press Ent and use the up/  
down arrow keys to select Normal or High. Press Ent to save.  
Note  
In the following fields, you are setting the MAXPRO-Net Server IP address and  
port number. To set the UltraKey Lite IP address or enter the main  
configuration menus, press Alt > Clr.  
7. Press the down LCD arrow key to scroll to Server IP. Press  
Ent and use the up/down arrow keys or the numeric keys to  
enter the Server IP address. Press Ent to save.  
Maxpro Settings  
Server IP:  
8. Press the down LCD arrow key to scroll to Server Port.  
Press Ent and use the up/down arrow keys or the numeric  
keys to enter the Server Port Address. Press Ent to save.  
MaxproServer IP  
_59.099.251.132  
9. After the MAXPRO settings are complete, press Alt > Clr to  
Maxpro Settings  
Server Port:  
exit the setup menu.  
Document 800-07422 Rev A  
08/10  
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Installing UltraKey Lite with MAXPRO-Net  
Step 4: Configure the Controller for an Ethernet Connection  
1. Press Alt > Clr to exit from the VideoBloX configuration menu.  
2. Press Alt > Clr a second time to enter the System Set top menu.  
3. Press the LCD down arrow key to scroll to the System Set:  
System Set:  
CONFIG  
Config menu.  
4. Press the right arrow key to enter the Configuration menus.  
5. Press the LCD up/down arrow keys to scroll through the options (serial port, network,  
language, back light, slider update, cascade linkage, hardware test, about).  
6. Scroll to the Configuration: Network menu, then press  
Configuration  
Ent.  
Network  
7. There are three sub-menus in this menu (Show Net Infor,  
DHCP, and Manual Settings). The structure is as follows:  
Network:  
Network  
DHCP  
DHCP  
Network:  
Show Net Infor  
Network:  
Show Net Infor  
Manual Setting  
Manual Setting  
Show Net Infor Menu  
The Show Net Infor Menu displays the Network information, including IP Address, DNS,  
Gateway, and Netmask.  
Automatically Configuring the Network Using DHCP  
The Dynamic Host Configuration Protocol (DHCP) is a computer networking protocol used  
by devices (DHCP clients) to obtain configuration information for operation in an Internet  
Protocol network. It is used to configure the network automatically.  
Automatically configuring the network using the DHCP menu:  
1. Press the LCD down arrow to scroll to the Network: DHCP  
Network:  
menu.  
DHCP  
2. Press Ent and the keyboard's network will be configured  
Please wait....  
automatically.  
•
•
If the network configuration is successfull, then a  
Succeeded! message displays.  
Succeeded!  
Failed!  
If the network configuration was not successful, then a  
Failed!message displays.  
58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
UltraKey Lite Controller Installation and User Guide  
When the nework configures successfully, the user can enter the  
Show Net Infor menu to see the IP Address, IP Address, DNS,  
Gateway and Netmask.  
Network:  
Manual Setting  
Manually Configuring the Network  
Manually configuring the network using the Manual Setting menu:  
1. Press the LCD down arrow key to scroll to the Network: Manual Setting menu  
2. When you are at the Network: Manual Setting menu, press Ent, then press the LCD  
up/down arrow keys to set the UltraKeyLite network parameters (IP address, gateway,  
netmask and DNS).  
3. Press the LCD up/down arrow keys to scroll through the  
Network:  
menu options to select IP Address, then press Ent to  
select.  
IP Address  
a. Using the numeric key pad, enter an IP address, then  
IP Address  
press Ent to save. The LCD menu displays the  
message: IPAddr Changed.  
159.099.251.230  
b. Press the up/down arrow keys to select Yes to save or  
IP Addr Changed  
No to cancel, then press Ent.  
Yes  
Note  
In this field, you are setting the UltraKey Lite IP address. To set the VideoBloX  
IP address (for communication purposes), see Step 3: Set and Configure for  
an Ethernet Connection.  
4. Press the LCD up/down arrow keys to scroll through the menu options and select  
Gateway. Press Ent.  
a. Using the number keys, enter a Gateway as required, then press Ent to save.  
The LCD menu displays the message: GW Changed.  
b. Press the up/down arrow keys to select Yes to save or No to cancel, then press  
Ent.  
5. Press the LCD up/down arrow keys to scroll through the menu options and select  
NetMask. Press Ent.  
a. Using the number keys, enter a NetMask as required, then press Ent to save.  
The LCD menu displays the message: NetMsk Changed.  
b. Press the up/down arrow keys to select Yes to save or No to cancel, then press  
Ent.  
6. Press the LCD up/down arrow keys to scroll through the menu options and select  
DNS. Press Ent.  
a. Using the number keys, enter a DNS as required, then press Ent to save.  
The LCD menu displays the message: DNS Changed.  
b. Press the up/down arrow keys to select Yes to save or No to cancel, then press  
Ent to save  
Document 800-07422 Rev A  
08/10  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing UltraKey Lite with MAXPRO-Net  
Step 5: Setting the Keyboard Address While Powering Up  
While powering up, when the Time Left 3 menu displays, press certain keys (see Table 4-4)  
to set the keyboard address.  
Table 4-4  
Setting the Keyboard Address  
Key  
Address  
Key  
Address  
11  
Alt > 1  
Alt > 2  
Alt > 3  
Alt > 4  
Alt > 5  
Alt > 6  
Alt > 7  
Alt > 8  
Alt > 9  
Alt > 0  
1
2
3
4
5
6
7
8
9
10  
Alt > F1  
Alt > F2  
Alt > F3  
Alt > F4  
Alt > F5  
Alt > F6  
Alt > F7  
Alt > F8  
Alt > F9  
12  
13  
14  
15  
16  
17  
18  
19  
Alt > F10 20  
(Optional) Configuring UltraKey Lite Using the Web Browser  
Logging into the Web Browser  
1. If not already done, navigate to, or copy and paste, the applicable IP address into  
your web browser:  
•
•
LAN connections: for example, http://192.168.1.9  
Crossover cable connections: for example, http://192.168.1.9 (default)  
2. In the User Name field enter Administrator (case sensitive).  
3. In the Password field enter 1234 (default).  
4. Click Login.  
60  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
UltraKey Lite Controller Installation and User Guide  
Figure 4-12  
UltraKey Lite Login page  
Step 1: Configure UltraKey Lite to MAXPRO Mode  
1. Log into the web browser.  
2. From the top menu, click the Configuration tab. See Figure 4-13.  
3. From the side menu, click the System Configurations tab.  
4. From the System Mode drop-down list, select MAXPRO.  
5. From the System Language drop-down list, select English or French.  
6. From the Background Light drop-down list select ON or OFF.  
7. Click Apply to save the configuration, Cancel to exit without saving or Default to  
restore all factory default values.  
Figure 4-13  
System Configuration Tab  
Step 2: Configure MAXPRO Network Settings  
1. From the side menu, click MAXPRO Configuration. See Figure 4-14.  
2. Under Keyboard ID Setting, enter a number between 1 and 99 to set the controller  
ID.  
Document 800-07422 Rev A  
08/10  
61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Installing UltraKey Lite with MAXPRO-Net  
3. Enter the IP address and Port Number of the MAXPRO-Net server under MAXPRO  
Device Network Setting.  
4. Under Serial Port Setting, select a Baud Rate from the drop-down list. Options are  
9600 or 19200 bps.  
5. Select a Connect Mode from the drop-down list. Options are 232 or 422.  
6. From the Joystick speed drop-down list, select Normal or High.  
7. Click Apply to save the configuration, Cancel to exit without saving or Default to  
restore all factory default values.  
Figure 4-14  
MAXPRO Configuration Tab  
Checking the Network Connection Using the Ping Function  
After the IP address is entered and applied, press the Ping button.  
•
•
A green Ping button indicates the device at this IP address has replied to the ping.  
A red Ping button indicates the device at the IP address did not reply. Please check  
that the IP address is correct and that there is a valid network path between the two IP  
addresses.  
Step 3A: Configure the Controller for a Serial Port Connection  
1. From the side menu, click Serial Port Configuration. See Figure 4-15.  
2. Under Serial Port1 Settings, select the following from each drop-down list as  
required:  
•
•
•
•
•
Baud Rate: 9600 or 19200 bps  
Parity: none, even or odd  
Stop Bits: 1 or 2 bits  
Data Bits: 7 or 8 bits  
Serial Mode: RS232, RS422 or RS485  
3. If required, repeat step 2 for Serial Port2 Settings.  
62  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
UltraKey Lite Controller Installation and User Guide  
4. Click Apply to save the configuration, Cancel to exit without saving or Default to  
restore all factory default values.  
Figure 4-15  
Serial Port Configuration Tab  
Step 3B: Configure the Controller for an Ethernet Connection  
1. From the side menu, click IP Configuration.  
2. In each of the fields, enter IP address, subnet mask, gateway and DNS values.  
3. Click Apply to save the configuration, Cancel to exit without saving or Default to  
restore all factory default values.  
Figure 4-16  
IP Configuration Tab  
Step 4: Configuring the Dynamic Keys  
You can configure the hard keys on the web server.  
1. From the side menu, click DynKey Configuration.  
Document 800-07422 Rev A  
08/10  
63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Installing UltraKey Lite with MAXPRO-Net  
Figure 4-17  
DynKey Configuration Tab  
2. In the drop-down menu, select the key you want to configure.  
3. In the right column, select the function you want to add to the hard key, then click  
Add.  
That selected function appears in the center column.  
4. Repeat step 3 to add another function to the selected key.  
5. Click Apply to save.  
Note  
Note  
No more than 10 functions can be configured to a hard key.  
Neither the number key (#) nor the Logon key can be configured.  
64  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
5
System Administration and Troubleshooting  
In this section:  
•
•
System Administration Using the Controller LCD, page 65  
System Administration Using the Web Browser, page 68  
System Administration Using the Controller LCD  
To navigate all configuration LCD menus, see Figure 5-3 on page 70.  
Logging in and Navigating to the System Set: Config Menu  
1. If not already done, install and connect the controller to a power source.  
The UltraKey Lite LCD displays.  
2. From the home screen, press Alt > Clr to enter the Password menu.  
3. Enter the PIN password 3434, then click Enter or Login.  
The System Set: Mode screen displays.  
Setting the Screen Language  
1. Log into the controller.  
2. From the System Set: Config menu, press the LCD  
Configuration  
Language  
up/down arrow keys to scroll to Language. Press Ent.  
3. Press the LCD up/down arrow keys to scroll through the  
options and select English or French. Press Ent to save.  
Document 800-07422 Rev A  
08/10  
65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
System Administration and Troubleshooting  
Adjusting the Back Light  
1. Log into the controller.  
2. From the System Set: Config menu, press the LCD  
up/down arrow keys to scroll to Back Light. Press Ent.  
Configuration  
Back Light  
3. Use the LCD up and down arrow keys or the rotate the  
touch pad to adjust the back light intensity.  
Updating the Touch Pad Firmware  
Slider firmware should be updated whenever a new slider firmware version is released.  
Check regularly to make sure that you are using the most up-to-date slider firmware.  
Note  
Slider firmware can be downloaded using the web browser. See Upgrading  
the UltraKey Lite Firmware on page 68 to download the firmware. Using the  
procedure on page 68 will download the slider firmware file, but will not apply  
the update. Use the following procedure to update the slider firmware after  
downloading the firmware file.  
1. Log into the controller.  
2. From the System Set: Config menu, press the LCD up/down arrow keys to scroll to  
Slider Update. Press Ent.  
3. The message Update Confirm? displays.  
4. Press the LCD up arrow key to select Yes or No.  
•
•
Select Yes and press Ent to upgrade the firmware.  
Select No and press Ent to cancel.  
5. If you select Yes, the message Slider Firmware: Downloaddisplays, followed  
by Download: OK.  
6. Press Ent to exit the menu.  
Viewing the Firmware Version  
1. Log into the controller.  
2. From the System Set: Config menu, press the LCD up/down arrow keys to scroll to  
About. Press Ent.  
The LCD scrolls to display the firmware version.  
3. Press any key to return to the previous menu.  
66  
Download from Www.Somanuals.com. All Manuals Search And Download.  
UltraKey Lite Controller Installation and User Guide  
Testing the Hardware  
1. Log into the controller.  
Configuration  
2. From the System Set: Config menu, press the LCD  
up/down arrow keys to scroll to Hardware Test. Press Ent.  
Hardware test  
3. Press the LCD up/down arrow keys and press Ent to select one or all of the following  
test options:  
•
•
Key: When you press a key, the key value and its state is displayed on LCD.  
Joystick: When you move the joystick, values which present the PTZ (pan, tilt,  
zoom) positions of the joystick are displayed on the LCD.  
•
•
Serial port: Confirms that the controller serial port is functioning.  
Slider: When you rotate the touch pad, specific values are displayed on the LCD.  
4. Press Alt > Clr to exit from these test menus.  
Restoring Defaults  
1. Log onto the controller.  
2. Use the LCD up/down arrow keys to scroll to Restore  
Default in the System Set: Config menu, then press Ent.  
A confirmation message Restore Defaults?appears in  
the display.  
Configuration  
Restore default  
3. Press the LCD up arrow key to select Yes or No.  
•
•
Select Yes, then press Ent to restore the defaults.  
Select No, then press Ent to cancel.  
Table 5-1  
Settings  
HJC5000 UltraKey Lite Controller Default Settings  
Protocol  
Network Settings for the Keyboard  
IP  
192.168.1.9  
255.255.255.0  
192.168.1.1  
192.168.1.1  
Net Mask  
GateWay  
DNS  
Default Mode: VideoBlox  
Maxpro Mode  
Keyboard ID  
Serial Port Mode  
Server Port  
1
RS232  
26026  
Server IP  
192.168.1.10  
Normal  
19200 bps  
Joystick Speed  
Baud Rate  
Document 800-07422 Rev A  
08/10  
67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
System Administration and Troubleshooting  
Table 5-1  
Settings  
HJC5000 UltraKey Lite Controller Default Settings (cont’d)  
Protocol  
VideoBlox Mode  
Address  
1
Baud Rate  
19200 bps  
Serial Port  
192.168.1.11  
Off  
Control Mode  
IP Address  
Default Back Light  
System Administration Using the Web Browser  
Logging into the Web Browser  
1. If not already done, navigate to, or copy and paste, the applicable IP address into  
your web browser:  
•
•
LAN connections: for example, http://192.168.1.9  
Crossover cable connections: for example, http://192.168.1.9 (default)  
2. In the User Name field enter Administrator (case sensitive).  
3. In the Password field enter 1234 (default).  
4. Click Login.  
Upgrading the UltraKey Lite Firmware  
1. Log into the web browser.  
2. From the top menu, click the Upgrade tab.  
The warning message: Please make sure the network connection is  
connected during system upgrading displays. See Figure 5-1.  
3. Click OK.  
The Software Upgrade menu opens.  
4. Select a Folder from the drop-down list: Application, FPGA, Kernel or Slider  
Firmware.  
5. In the Select File field, click Browse. Navigate to the file and click OK.  
6. Click Send to start the upgrade process.  
The Upgrade Status window opens. Messages display to indicate when old files are  
being erased and new files are being copied.  
68  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
UltraKey Lite Controller Installation and User Guide  
When the process is complete, the message Upgrade successdisplays and the  
system reboots.  
WARNING!  
Do not power off the keyboard during upgrading. Serious  
damage can occur to the firmware, rendering the keyboard  
inoperable.  
Figure 5-1  
Software Upgrade Warning Message  
Rebooting UltraKey Lite  
1. Log into the web browser.  
2. From the top menu, click the System Reboot tab.  
The Reboot System window opens.  
3. Click Reboot to continue or click another tab or Logout to exit without rebooting.  
Changing the UltraKey Lite Web Browser Password  
1. Log into the web browser.  
2. In the upper right corner, click Change Password. See Figure 5-2.  
3. In the Old Password field, enter the current password  
4. In the New Password field, enter a new password  
5. Enter the new password in the Confirm New Password field.  
6. Click Apply to set the new password or Cancel to exit without changing it.  
Figure 5-2  
Change Password Page  
Document 800-07422 Rev A  
08/10  
69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
System Administration and Troubleshooting  
Figure 5-3  
System Configuration LCD Menu Tree - All Modes  
Keyboard ID  
Maxpro  
Settings  
Serial Port  
Mode  
Address  
Server Port  
Server IP  
Baud Rate  
VB Settings  
Control Mode  
IP Address  
Joystick Speed  
Baud Rate  
Restore  
Defaults  
About  
Key  
Serial Port  
Hardware Test  
Slider  
System Set:  
Configuration  
Configuration  
Joystick  
Slider  
Update  
Adjust Bg Light  
Back Light  
Up/Down Slide  
Language  
Network  
English/French  
Show Net Infor  
Manual Setting  
DHCP  
70  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Download from Www.Somanuals.com. All Manuals Search And Download.  
Honeywell Systems Group Northern Europe  
Ampèrestraat 41  
1446 TR Purmerend, The Netherlands  
www.honeywell.com/security/nl  
+31.299.410.200  
Honeywell Systems Group (Head Office)  
2700 Blankenbaker Pkwy, Suite 150  
Louisville, KY 40299, USA  
www.honeywellvideo.com  
+1.800.796.2288  
Honeywell Systems Group Deutschland  
Johannes-Mauthe-Straße 14  
D-72458 Albstadt, Germany  
www.honeywell.com/security/de  
+49.74 31.8 01.0  
Honeywell Systems Group Europe/South Africa  
Aston Fields Road, Whitehouse Industrial Estate  
Runcorn, Cheshire, WA7 3DL, UK  
www.honeywell.com/security/uk  
+44.01928.754028  
Honeywell Systems Group Caribbean/Latin America  
9315 NW 112th Ave.  
Miami, FL 33178, USA  
Honeywell Systems Group France  
Immeuble Lavoisier  
www.honeywellvideo.com  
+1.305.805.8188  
Parc de Haute Technologie  
3-7 rue Georges Besse  
92160 Antony, France  
Honeywell Systems Group Pacific  
Level 3, 2 Richardson Place  
North Ryde, NSW 2113, Australia  
www.honeywellsecurity.com.au  
+61.2.9353.7000  
www.honeywell.com/security/fr  
+33.(0).1.40.96.20.50  
Honeywell Systems Group Italia SpA  
Via della Resistenza 53/59  
20090 Buccinasco  
Milan, Italy  
www.honeywell.com/security/it  
+39.02.4888.051  
Honeywell Systems Group Asia  
35F Tower A, City Center, 100 Zun Yi Road  
Shanghai 200051, China  
www.asia.security.honeywell.com  
+86 21.5257.4568  
Honeywell Systems Group Middle East/N. Africa  
Post Office Box 18530  
Honeywell Systems Group España  
Avenida de Italia, n° 7  
LOB Building 08, Office 199  
P.I. - C.T.C. Coslada  
Jebel Ali, Dubai, United Arab Emirates  
www.honeywell.com/security/me  
+971.04.881.5506  
28820 Coslada, Madrid, Spain  
www.honeywell.com/security/es  
+34.902.667.800  
www.honeywellvideo.com  
+1.800.796.CCTV (North America only)  
[email protected]  
Document 800-07422 – Rev A – 08/10  
© 2010 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written  
permission from Honeywell. The information in this publication is believed to be accurate in all respects. However, Honeywell cannot  
assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change  
without notice. Revisions or new editions to this publication may be issued to incorporate such changes.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Graco Stroller ISPA189AA User Manual
Haier TV DVD Combo 0090502138 User Manual
Healthrider Treadmill HRTL19980 User Manual
Honeywell Air Cleaner F35F User Manual
Hoshizaki Ice Maker KM 800MAE User Manual
HP Hewlett Packard Computer Accessories t5530 User Manual
HP Hewlett Packard Computer Accessories T8671 91017 User Manual
IBM Mouse G Mouse GPS Receiver G Mouse MR User Manual
Ide Line Fondue Maker 743 089 User Manual
iHome Headphones IB24 User Manual