Honeywell Home Security System LYNXR Series User Manual

ADEMCO LYNXR Series

Security Systems

LYNXR/LYNXR24 and LYNXR-EN

Installation and Setup Guide

OFF

AWAY

STAY

AUX

K5963V3bx 5/04 Rev. A

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

SYSTEM FEATURES...............................................................................................................................................4

MOUNTING THE CONTROL..................................................................................................................................5

WIRING CONNECTIONS........................................................................................................................................6

AC POWER AND BACKUP BATTERY...................................................................................................................9

INSTALLING WIRELESS ZONES........................................................................................................................11

MECHANICS OF PROGRAMMING .....................................................................................................................14

ZONE RESPONSE TYPE DEFINITIONS ............................................................................................................15

DATA FIELD DESCRIPTIONS.............................................................................................................................17

✻55 ENABLING THE 5842 WIRLESS DIALER ..................................................................................................25

✻56 ENHANCED ZONE PROGRAMMING MODE.............................................................................................27

✻80 DEVICE PROGRAMMING MENU MODE ...................................................................................................31

✻81 ZONE LIST MENU MODE.............................................................................................................................34

✻83 ENHANCED SEQUENTIAL MODE .............................................................................................................35

✻84 ASSIGN ZONE VOICE DESCRIPTORS .......................................................................................................38

✻85 RECORD CUSTOM VOICE DESCRIPTORS................................................................................................40

VOICE PROMPT PROGRAMMING......................................................................................................................41

REMOTE PROGRAMMING/CONTROL (DOWNLOADING) .............................................................................45

SYSTEM OPERATION...........................................................................................................................................47

TESTING THE SYSTEM........................................................................................................................................53

SYSTEM COMMUNICATION...............................................................................................................................54

TROUBLESHOOTING GUIDE .............................................................................................................................56

CONTACTING TECHNICAL SUPPORT..............................................................................................................58

REGULATORY AGENCY STATEMENTS ...........................................................................................................59

SPECIFICATIONS..................................................................................................................................................60

LYNXR/LYNXR24 PROGRAMMING DEFAULT TABLES.................................................................................61

LYNXR-EN PROGRAMMING DEFAULT TABLES............................................................................................62

INDEX......................................................................................................................................................................65

LIMITATIONS OF THIS SYSTEM STATEMENT...............................................................................................69

WARRANTY ............................................................................................................................................................70

SUMMARY OF CONNECTIONS DIAGRAM.......................................................................................................71

–3–

Download from Www.Somanuals.com. All Manuals Search And Download.

System Features

LYNXR and LYNXR-EN are not intended for UL985 Household Fire applications unless a 24-hour backup

battery (P/N LYNXRCHKIT-HC) is installed.

Powerline Carrier Devices are not UL Listed for fire or burglary functions and are intended for home

automation.

The LYNXR-Series controls are self-contained, rechargeable wireless control/communicators that feature easy

installation and usage. A built-in speaker provides voice annunciation of system status along with voice descriptors of

each zone (LYNXR-EN if programmed). The following illustration highlights the main features of this system.

FEATURES

SYSTEM POWER

•Primary Power: Ademco

1332/1332X10 Plug-in Transformer,

110VAC to 9VAC, 15VA output

(1332CN in Canada)

•Backup battery: Six 1.2V

rechargeable nickel-metal hydride

batteries.

ZONES and DEVICES

•1 hardwire zone

•Up to 24 wireless zones

(5800 Series Transmitters)

•Up to 16 wireless button zones

•Up to 8 Powerline Carrier Devices

•Supports wireless keypads

•Real-time Clock display and Fixed-Word display

•Message Center (for user recorded messages)

•Voice announcement of system and zone status

•Voice chime

•Alarm Clock

•Reminder

•X-10 Scheduling

•Latch Key Reports

•Automatic Stay Arming

•Remote Phone Control

•“Follow Me” Reminder and System Announcements

8 USER CODES

• Installer code

• Master code

• 5 Secondary codes

• Duress code

• 3 Panic functions

OFF

AWAY

COMMUNICATION

• Ademco Low Speed

• Sescoa/Radionics

• Ademco Express

• Ademco Contact ID

• Paging feature

STAY

AUX

ALARM OUTPUT

•Built-in sounder

•Piezo output

(30mA max.)

•Bell output

(120mA max.)

•Steady output for

burglary/panic

•Temporal pulse

output for fire alarms

•Long Range

Radio/Alarm audio

verification

PROGRAMMING

•Options stored in EEROM

•Can be uploaded, downloaded or

controlled via IBM-compatible

computer using Compass

downloader software and specified

HAYES modem

•Voice Prompt programming mode

SPECIAL FEATURES

LYNXR24

•24-hour backup

LYNXR-EN

•Two-way voice communication

•Speaker phone operation

OTHER FEATURES

•Exit error feature (detects difference between an

actual alarm and exit alarm caused by leaving a

door open after the exit delay expires)

•Event log stores up to 84 events

•Macro/ 1-button paging

•RF Jam Detection

•Remote phone control

•Compatible with 5842 Wireless Dialer

•Compatible with encrypted (high-security) devices

–4–

Download from Www.Somanuals.com. All Manuals Search And Download.

Mounting the Control

Wall Mounting

The illustration below shows the front assembly separated from the back plate.

DO NOT disconnect the ribbon cable from the terminal strip board. Disconnect the cable only from the

front assembly board.

Certain features differ between the LYNXR/LYNXR24 and the LYNXR-EN models. Verify the specific model

being installed prior to programming the system.

LOCKING TABS

1. Separate the front assembly from the

back plate by pressing on the two

locking tabs at the top of the unit.

2. Carefully disconnect the ribbon cable

from the front assembly, leaving the

ribbon cable connected to the

terminal block PC board. The back

plate contains the terminal block for

making wiring connections.

PC BOARD

PART NUMBER

LOCATION

MXXXX K5108

3. Mount the back plate to a sturdy wall,

feeding the field wiring through the

appropriate openings in the back

plate.

4. After wiring connections are made,

RED WIRE

MARKING

carefully reconnect the ribbon cable to

the front assembly PC board

connector (properly aligning the red

wire).

5. Before closing the assembly, verify

DISCONNECT

THIS END ONLY!

which LYNXR model is being installed

by checking the model number printed

on the PC Boards. (Example:

SALYNXREN indicates the unit being

installed is a LYNXR-EN.)

PC BOARD

PART NUMBER

LOCATION

6. Snap the front assembly to the back

plate so it is secured by the locking

tabs.

01009-003-V0

Desktop Mounting

If desired, an optional mounting base (model LYNX-DM, purchased separately) allows the LYNXR-Series controls to be

used on a desktop.

1. Slide the control panel onto the

mounting base locking tabs.

2. Bring all wiring through the bottom of

the mounting base, using one of the

three wire entry locations, before

OFF

ESCAPE

AWAY

ADD

STAY

making connections to the control

panel.

DELETE

AUX

SELECT

3. Use tie-wraps to secure the wiring to

the built-in wire loops as needed. Use

the two supplied screws to secure the

control panel to the mounting base.

WIRE ENTRY

KNOCKOUT

(1 of 3)

01009-004-V1

–5–

Download from Www.Somanuals.com. All Manuals Search And Download.

Wiring Connections

Wiring Overview

The following summarizes the connections required. Refer to the Wiring Connections paragraph and the Summary of

Connections diagram on the inside back cover when making connections.

HARDWIRE ZONE

Supports 1 EOLR supervised zone using either closed

circuit or open circuit sensors.

Devices.

LONG RANGE RADIO

Compatible with the ALARMNET 7845C and 7720

POWERLINE CARRIER DEVICES

Supports up to 8 Powerline Carrier

Devices for turning on/off lights and

appliances. Requires the use of an

ADEMCO 1332X10 transformer.

TWO-WAY VOICE

The LYNXR-EN supports the two-way

voice feature/Alarm Audio Verification.

The LYNXR and LYNXR24 require the

installation of the LYNXAVM.

PHONE LINES

Use either the plug-in jacks or

the screw terminals.

MXXXX K5108

AC TRANSFORMER

Use the supplied

ADEMCO 1332X10

9VAC, 15VA Plug-in

Transformer (1332CN in

Canada).

01009-005-V0

EARTH GROUND

See Earth Ground paragraph.

SOUNDERS

The system includes a built-in sounder in the master keypad. If

desired, an external bell or piezo sounder can be connected.

Bell: Use a 6-14V bell with maximum current drain of 120mA.

Piezo: Use a 6-14V piezo sounder with maximum current drain of

30mA.

This control complies with NFPA requirements for temporal pulse

sounding of fire notification appliances.

LOCAL SOUNDER DISABLE JUMPER

Remove the shorting jumper (shunt) to disable local

sounder, leaving only the external sounder active.

UL NOTE: Do not remove the shorting jumper (the shunt)

for UL installations.

Temporal pulse sounding for a fire alarm consists of the following:

3 pulses – pause – 3 pulses – pause – 3 pulses. . .

Wiring Connections

1. Make Earth Ground Connection - The designated earth ground terminal (1) must be terminated in a good earth ground

for the lightning transient protective devices in this product to be effective. The following are examples of good earth

grounds available at most installations:

Metal Cold Water Pipe - Secure a non-corrosive metal strap (copper is recommended) to the pipe that is electrically

connected and secured to which the ground lead.

AC Power Outlet Ground - Available from 3-prong, 120VAC power outlets only. To test the integrity of the ground

terminal, use a three-wire circuit tester with neon lamp indicators, such as the UL Listed Ideal Model 61–035, or

equivalent, available at most electrical supply stores.

a. Connect terminal 1 to a good earth ground.

–6–

Download from Www.Somanuals.com. All Manuals Search And Download.

Wiring Connections

INCOMING

PHONE LINE

RING

TIP

2. Make Phone Line Connections - For local or full line

seizure proceed to the appropriate steps below.

Local Seizure

RED

GREEN

a. Connect the incoming phone line to either the

8-position jack or terminals 2 (TIP) and 3 (RING) on

the Lynx.

b. Connect the handset phone lines to either the RJ11

jack or terminals 4 (TIP) and 5 (RING).

Full Line Seizure: The control must be placed in

series with the incoming phone line. Plugging the

Direct Connect Cord directly into the RJ31X jack, allows

the control to seize the phone line when an alarm

occurs and normal phone line usage by the premises

phones if the plug needs to be removed.

PREMISES PHONES

RING

RJ31X

TIP

BROWN

GREY

DIRECT

CONNECT

CORD

a. Cut the incoming RING and TIP phone lines

(typically red and green, respectively) and connect

them to RJ31X terminals 4 (red) and 5 (green).

b. Connect the premises end of the cut RING and TIP

wires to RJ31X terminals 1 (grey) and 8 (brown)

respectively.

c. Wire the flying leads of a Direct Connect Cord to the

control’s phone terminals as shown in the diagram

or plug into the 8-position jack.

8-POSITION

JACK

TIP

RING TIP RING

INCOMING

PHONE LINE PREMISES

PHONES

01000-008-V0

Full Line Seizure Connections

d. Plug the Direct Connect Cord into the RJ31X jack.

HARDWIRED ZONE: If the EOLR is not at the end of the loop, the zone will not be properly

supervised, and the system may not respond to an open circuit on the zone.

3. Make Hardwired Zone Connections - Zone 1 is an EOLR supervised zone that supports both open circuit and closed

circuit devices and has a response time of 350msec. Maximum zone resistance: 300 ohms, plus EOLR

Note: The hardwire zone cannot be used as a fire zone.

a. Connect sensors/contacts to the hardwired zone terminals 6 (+) and 7 (–). Refer to the Summary of Connections

diagram.

b. Connect closed circuit devices in series in the high (+) side of the loop. The EOL resistor must be connected in

series with the devices, following the last device.

c. Connect open circuit devices in parallel across the loop. The 2000-ohm EOLR must be connected across the loop

at the last device.

4. Make External Sounder Connections - The control panel supports either a 6-14VDC piezo sounder (30mA max.) or

6-14VDC bell (120mA max.; e.g. ADEMCO WAVE2EX).

a. Connect a piezo sounder to terminals 10 (+) and 11 (–); OR a bell to terminals 11 (–) and 12 (+).

LOCAL SOUNDER DISABLE: The Master Keypad’s built-in piezo sounder can be disabled by

removing the shorting jumper (shunt) on the terminal board. If disabled, however, no sounding

will occur upon AC loss, since the external sounder does not operate when AC power is lost.

Do not remove shorting jumper (the shunt) for UL installations.

5. Disable Local Sounder Option - If required the Master Keypad’s built-in piezo sounder can be disabled.

a. Remove the shorting jumper (shunt) on the terminal board.

6. Make Powerline Carrier Device Connections - The control panel supports up to 8 Powerline Carrier Devices. If using

these devices, they must be connected to the ADEMCO 1332X10 transformer, as shown in the SUMMARY OF

CONNECTIONS diagram.

a. Connect the com/data/sync/ lines from the ADEMCO 1332X10 transformer to terminals 9, 13, and 14, respectively.

Note: If not using the supplied Ademco connection cable, you may need to reverse the black and yellow wire connections. Refer to the

✻80 Device Programming Menu Mode section for details on programming Powerline Carrier Devices.

–7–

Download from Www.Somanuals.com. All Manuals Search And Download.

Wiring Connections

ALL OUTPUT CIRCUITS ARE POWER LIMITED.

WARNING:

TO PREVENT RISK OF SHOCK

DISCONNECT TELEPHONE LINE

AT TELECOM JACK BEFORE

SERVICING THIS UNIT.

AAV / LRR

TRIGGER

(LYNXR/LYNR24)

LRR

TRIGGER

(LYNXR-EN)

EARTH

GROUND

PHONE

ZONE

SOUNDERS

PLCD

( )

(+)

POS

JACK

RJ11

(+)

( )

DATA

OUT

TIP RING TIP RING

(+)

SYNC

HARD

WIRED

ZONE

INCOMING

PHONE

LINE

HANDSET

PHONE

LINE

LOCAL SOUNDER

DISABLE SHUNT

REMOVE TO

DISABLE

TRIGGER

SIGNAL

(NEG)

INCOMING

TELEPHONE

LINE

1332/

1332X10/

1332CN

PLUG-IN

EARTH

GROUND

PREMISES

TELEPHONE

PIEZO

TRANSFORMER

9VAC, 15VA

BELL

2k OHMS

EOLR

6-14VDC

30mA max.

6-14VDC

120mA max.

(e.g. WAVE2EX)

THE LYNX SERIES CONTROLS ARE

EQUIPPED WITH AN INTEGRAL

RECHARGEABLE BATTERY PACK.

SYNC

COM

DATA

WEEKLY TESTING IS

REQUIRED TO ENSURE

PROPER OPERATION

OF THIS SYSTEM

LYNXR:

LYNXR24:

LYNXR-EN:

P/N LYNXRCHKIT-SC

P/N LYNXRCHKIT-HC

P/N LYNXRCHKIT-SC

NOTE

1332X10

ONLY

CONNECTIONS

P/N LYNXRCHKIT-HC

USE ONLY 1332/1332X10 OR 1332CN

REPLACE EVERY FOURYEARS

TRANSFORMERS PROVIDED

01009-009-V0

–8–

Download from Www.Somanuals.com. All Manuals Search And Download.

AC Power and Backup Battery

The system is powered by a 9VAC, 15VA Plug-in Transformer, ADEMCO 1332/1332X10 (1332CN in

Canada). Refer to the wiring table below for wire gauge and length.

Distance from Transformer

to Control

Wire Gauge

Use only the provided ADEMCO

1332/1332X10 or 1332CN Transformer

Up to 75 feet

#20

#18

#16

75 to 150 feet

150 to 300 feet

Wiring to the AC Transformer must not exceed 300 feet using 16-gauge wire. The voltage reading between

terminals 15 and 16 of the control must not fall below 9.00VAC.

Do not plug the transformer into the AC outlet until after all wiring connections have been made.

Backup battery. In the event of an AC power loss, the system is supported by a long life backup battery that

is supervised for connection and for low voltage conditions. If the battery is missing, or a low battery condition

is detected, a “low battery” message is displayed and a report is sent to the central station. In addition, the

system will beep once every 45 seconds to audibly indicate a low battery condition (press any key to stop the

beeping).

AC Power and Rechargeable Backup Battery

Connecting AC Power and backup battery

RETAINER

NOTE

LYNXRCHKIT-HC

BATTERY PACK SHOWN

1. Connect wires from the 1332/1332X10 (1332CN in

Canada) AC Transformer to terminals 15 and 16 as

shown in the wiring diagram.

BATTERY

2. Remove battery retainer.

PACK

3. Peel the backing from tape on the back plate.

4. Insert battery pack into back plate.

5. Install battery retainer.

TAPE

6. Connect battery connector to receptacle on

terminal block PC board.

7. After all wiring connections have been made, snap

the front assembly to the back plate and plug the

XXXX

K5108

transformer into a 24-hour, 110VAC unswitched

outlet.

Note: Rechargeable batteries may take up to 48-hours to

fully charge. The “LOW BAT” message should clear

within four hours or by entering Test Mode.

BATTERY

RECEPTACLE

WIRING

TERMINALS

01009-007-V0

Ensure the cover is snapped closed prior to applying AC power.

–9–

Download from Www.Somanuals.com. All Manuals Search And Download.

AC Power and Backup Battery

AC Power and Rechargeable Backup Battery

The LYNXR Series is equipped with an integral, replaceable, rechargeable battery pack composed of six (6)

rechargeable 1.2-volt nickel-metal hydride batteries. Select the appropriate battery pack, based on the

installation’s requirement, and install the battery pack.

Model/Part Number

LYNXRCHKIT-SC

Battery StandbyTime

4-hours (minimum)

Low Battery Notification

Approximately 1-hour before battery depletion

LYNXRCHKIT-HC

24-hours (minimum)

At least 1-hour before battery depletion

Replacing the Rechargeable Battery

1. When battery replacement is required, unplug

the transformer from the wall outlet, and open

the control panel cover.

LYNXRCHKIT-HC

LYNXRCHKIT-SC

RETAINER

2. Remove the battery retainer and disconnect the

battery pack connector from the receptacle on

the terminal block PC board.

BATTERY

PACK

3. Remove the battery pack from the back plate.

4. If required, replace the tape that secures the

battery pack.

TAPE

5. Install

replacement battery pack (P/N

BATTERY

CONNECTOR

LYNXRCHKIT-SC or LYNXRCHKIT-HC) into the

back plate.

6. Install the battery retainer.

7. Connect the battery connector to the

XXXX

K5108

receptacle on the terminal block PC board.

8. After the wiring connection has been made,

snap the front assembly to the back plate.

BATTERY

RECEPTACLE

9. Plug the transformer into a 24-hour, 110VAC

unswitched outlet.

01009-006-V0

10.Rechargeable batteries may take up to 48-

hours to fully charge. The “LOW BAT” message

should clear within four hours or by entering

Test Mode.

Ensure the control panel assembly is snapped closed prior to applying AC power.

–10–

Download from Www.Somanuals.com. All Manuals Search And Download.

Installing Wireless Zones

General Information

Zones: The control supports up to 24 wireless zones using 5800 Series transmitters, and up to 16

wireless buttons.

Range: The built-in RF receiver can detect signals from wireless transmitters within a nominal

range of 200 feet.

Transmitters: 5800 Series transmitters have built-in serial numbers that must be entered into the

system using the ✻56 or ✻83 interactive mode, or input to the control via the downloader. 5800

Series transmitters (except the 5800RL and 5827, described separately) do not have DIP switches.

Each transmitter's zone number is programmed into the system in ✻56 mode. Some transmitters,

such as the 5816 and 5817, can support more than one "zone" (referred to as loops or inputs). On the

5816, for example, the wire connection terminal block is loop 1,the reed contact is loop 2. Each loop

must be assigned a different zone number.

The 5816 and 5817 Transmitters do not have EOL supervision of their loop wiring. Therefore, for

UL Household Burglary installations, the loop wiring may not exceed 3 feet.

The 5800RL, 5802MN, 5802MN2, 5804, 5804BD, 5804BDV, 5804E, 5804WATCH, 5814, 5816TEMP,

5819, 5819S(WHS & BRS), and 5850(GBD) transmitters are not intended for any UL installations.

For button transmitters (RF "keys") such as the 5804 and 5801, you must assign a unique zone

number to each individual button used on the transmitter. Each button on the transmitter also has

a pre-designated loop or input number, which is automatically displayed.

House Identification

If you are using a 5804BD/5804BDV, or 5827 Wireless Keypad with

the system, you must program a House ID Code (01–31) in field ✻24

to establish proper communication, and the keypad must be set to

the same ID. House ID 00 disables all wireless keypads. An RF

House ID is not necessary for other 5800 Series transmitters; the

entry should be left at “00” (default) in those cases. The 5827 reports

low battery status as zone “00”.

•

••

•

5804BD/5804BDV

5827

Transmitter Supervision

Except for some transmitters/keypads that may be carried off-

premises (5804, 5804BD, 5804BDV, 5804E, 5804WATCH, and

5827), each transmitter is supervised by a check-in signal that is

sent to the receiver at 70–90 minute intervals. If at least one check-

in is not received from each supervised transmitter within a 12-

hour period, the "missing" transmitter number(s) and "FAULT" will

be displayed. The supervision for a particular transmitter in the

system that may also be carried off the premises (5801, 5802MN)

may be turned off by entering it as a "UR" (unsupervised RF) type,

as described in the ✻56 Enhanced Zone Programming Mode section.

5800 Series transmitters have built-in tamper protection and will

annunciate as a fault condition if covers are removed.

5816

5806/5807/5808

5890 / 5890PI

01009-010-V1

Transmitter Input Types

Each of the following transmitters has one or more unique factory-assigned input (loop) ID codes.

Each of the inputs requires a programming zone (e.g., a 5804's four inputs require four button zones).

Transmitters can be entered as one of the following types (see transmitter’s instructions for appropriate

input type):

Type

Description

"RF" (Supervised RF)

Sends periodic check-in signals, as well as fault, restore, and low battery signals. The

transmitter must remain within the receiver's range.

"UR" (Unsupervised RF)

Sends all the signals that the "RF" type does, but the control does not supervise the

check-in signals. The transmitter may therefore be carried off-premises.

"BR" (Unsupervised Button RF)

These only send fault signals. They do not send low battery signals until they are

activated. The transmitter may be carried off-premises.

–11–

Download from Www.Somanuals.com. All Manuals Search And Download.

Installing Wireless Zones

Transmitter Battery Life

• Batteries in the wireless transmitters may last from 4–7 years,

depending on the environment, usage, and the specific wireless device

being used. Factors such as humidity, high or low temperatures, as well

as large swings in temperature may all reduce the actual battery life in a

given installation. The wireless system can identify a true low battery

situation, thus allowing the dealer or user of the system time to arrange

a change of battery and maintain protection for that point within the

system.

5801

5802MN

• Button-type transmitters should be periodically tested for battery life.

The 5801, 5802MN, 5802MN2, 5804, 5804BD, 5804BDV, 5804E, and

5804WATCH button transmitters have replaceable batteries.

Using the Transmitter Sniffer Mode

Use this mode after all transmitters have been entered to check that all

transmitters have been properly programmed.

5804 /5804E

01009-011-V0

1. Enter Installer code (4112) + [#] + 3.

Note: If the communicator is in the process of sending a report to the central station, the system will not go into the Sniffer mode.

If so, wait a few minutes and try again.

2. The keypad will display all zone numbers, which have a non-zero Zone Type (even if serial

numbers were not learned yet). Fault each transmitter in turn, causing each one to send a

signal. As the system receives a signal from each of the transmitters, the zone number of that

transmitter will disappear from the display. The transmitters may be checked upon

installation, or in an installed system.

3. When all transmitters have been checked, exit Sniffer mode. Enter Installer Code (4112) +

OFF.

Notes: (1) Sniffer mode does not automatically expire. You must manually exit (Installer Code + OFF) Sniffer mode to return to normal

operation.

(2) All BR-type units must physically be activated to clear the display, since they do not automatically send check-in signals.

(3) When one button of a transmitter (RF, UR, or BR) is activated, all zones assigned to other buttons on that transmitter are

cleared. This also applies to 5816 and 5817 transmitters that have multiple loops (zones).

(4) Any transmitter that is not “entered” will not turn off its zone number.

Go/No Go Test Mode

Note: Encrypted (high-security) devices must be activated while the system is in Go/No Go Test Mode. Refer to the transmitter’s

installation instructions for complete details.

The Go/No Go tests will verify adequate RF signal strength from the proposed transmitter location,

and allow you to reorient or relocate transmitters if necessary, before mounting the transmitters

permanently.

This mode is similar to the transmitter Test mode, except that the wireless receiver gain is reduced.

This will enable you to make sure that the RF signal from each transmitter is received with

sufficient signal amplitude when the system is in the normal operating mode.

1. Enter Installer Code (4112) + [#] + 8.

2. Once you have placed transmitters in their desired locations and the approximate length of wire

to be run to sensors is connected to the transmitter's screw terminals (if used), fault each

transmitter.

Conducting this test with your hand wrapped around the transmitter will cause inaccurate results.

Note: On button type transmitters that have been programmed to set ARM AWAY, ARM STAY, or DISARM, pressing a button will take the

system out of the Go/No Go Test mode and cause the programmed action.

a. The keypad will beep three times indicating signal reception and will display the appropriate

zone number.

b. If the keypad does not beep, reorient or move the transmitter to another location. Usually a

few inches in either direction is all that is required.

4. If each transmitter produces the proper keypad response when it is faulted, you can then

permanently mount each of the transmitters according to the instructions provided with them.

5. Exit the Go/No Go Test mode by entering: Installer Code (4112) + OFF.

–12–

Download from Www.Somanuals.com. All Manuals Search And Download.

Installing Wireless Zones

5800 Series Transmitter Loop Numbers (Refer to this information when programming transmitters)

The following illustration shows the compatible transmitters, their associated input types and loop

designations.

LOOP 4

LOOP 3

LOOP 2

LOOP 4

YOU MUST

ENROLL

YOU MUST

ENROLL

THIS

LOOP 4

YOU MUST

ENROLL

THIS

LOOP 4

YOU MUST

ENROLL

THIS

LOOP 2

LOOP 1

LOOP 2

LOOP 1

BUTTON

LOOP 1

LOOP 2

LOOP

THIS BUTTON

LOOP 3

BUTTON

•

LOOP 1

•

LOOP 3

•

••

•

5800RL

SET

HOUSE ID

5801

ENROLL AS

"UR" OR "RF"

5802 MN2

ENROLL AS

"UR" OR "RF"

5804/5804E

ENROLL AS "BR"

5804BD/5804BDV

ENROLL AS "BR"

PROGRAM HOUSE ID

5804WATCH

5802 MN

ENROLL AS

"UR" OR "RF"

LOOP 1

LOOP 2

(PRIMARY)

(REED)

LOOP 2

(REED)

LOOP 2

(AUX.

CENTER)

LOOP 1

(TERMINALS)

LOOP 1

(TERMINALS)

LOOP 1

(TEMP

SENSOR)

ALTERNATE

POSITION

FOR LOOP 2

LOOP 3

(AUX.

RIGHT)

LOOP 1

5816

ENROLL AS "RF"

5816MN

ENROLL AS "RF"

5816TEMP

ENROLL AS "RF"

5817

ENROLL AS "RF"

5818

ENROLL AS "RF"

5806/5807/5808/5808LST

ENROLL AS "RF"

5809

ENROLL AS "RF"

5814

ENROLL AS "RF"

LOOP 2

(REED)

ARM

LOOP 2

(REED)

READ

LOOP 1

(SOUND)

LOOP 3

LOOP 1

(MOTION)

(TERMINALS)

LOOP 1

(INTERNAL

SHOCK

)

LOOP 1

(TERMINALS)

)

SENSOR

llow

)

LOOP 3

(TERMINALS)

5819

ENROLL AS "RF"

5819S (WHS & BRS)

ENROLL AS "RF"

5827

PROGRAM

HOUSE ID

5827BD

PROGRAM

HOUSE ID

5828V

PROGRAM

HOUSE ID

5849

ENROLL AS "RF"

5850 (GBD)

ENROLL AS "RF"

5890/5890PI

ENROLL AS "RF"

01009-012-V3

Note: Loop 4 must be enrolled on the 5801, 5804, 5804BD, 5804BDV, 5804E and 5804WATCH transmitters, whether or not the loop is used.

The 5800RL, 5802MN, 5802MN2, 5804, 5804BD, 5804BDV, 5804E, 5804WATCH, 5814, 5816TEMP, 5819, 5819S(WHS

& BRS), and 5850(GBD) wireless transmitters are not intended for any UL installations.

Setting DIP Switches on the 5800RL and 5827 Transmitter(s)

Set the 5800RL and 5827 Transmitters to the programmed House ID, by using the DIP switches.

(OFF position is indicated by ---)

Notes: (1) The 5827 transmitter cannot be used in conjunction with the ✻58 RF Jam Detection feature.

(2) The 5800RL cannot be used in conjunction with the Auto Arm (scheduled arming) feature.

5800RL DIP SWITCH TABLE

SWITCH UP FOR "ON"

House

DIP SWITCH POSITIONS

House

DIP SWITCH POSITIONS

---

SW-1 ACTIVATES

MODE SETTING

SW-6 SETS

MODE

SWITCH DOWN

FOR "OFF"

---

2-6 SETS HOUSE ID

SHOWN SET FOR HOUSE ID# 12

01000-014-V1

Setting 5800RL DIP Switches

5827 WIRELESS KEYPAD DIP SWITCH TABLE

SWITCH UP FOR "ON"

House

DIP SWITCH POSITIONS

House

DIP SWITCH POSITIONS

---

SWITCH DOWN FOR "OFF"

---

HOUSE ID

---

SHOWN SET FOR HOUSE ID# 30

01000-013-VO

---

Setting 5827 DIP Switches

–13–

Download from Www.Somanuals.com. All Manuals Search And Download.

Mechanics of Programming

General Programming Information

Programming options are stored in non-removable, electrically erasable, nonvolatile EEROM memory. The

system can be programmed at any time, even at the installer's premises prior to the actual installation.

Simply apply power temporarily to the Control and then program the unit as desired. There are two

programming modes:

• Data field programming (used for setting various system options)

• Interactive menu mode programming (used for programming zone information, programming Powerline Carrier

Devices, and for entering transmitter serial numbers)

The system can also be programmed remotely, using an IBM Personal Computer, a modem, and Compass Downloader

for Windows. See the Remote Programming/Control (Downloading) section.

Note: You may find it convenient to adjust the volume setting before entering the Program Mode. This will allow you to clearly hear the

feedback announcements or system beeps in the Programming Mode, of the system’s built-in speaker. To adjust the volume, press

FUNCTION + VOLUME+ [3] or [6]. Upon exiting the Program Mode, the system will reset the volume to the default value (mid level).

Certain features differ between the LYNXR/LYNXR24 and the LYNXR-EN models. Verify the specific model being

installed prior to the system programming.

Entering Program Mode - Use one of the following methods to enter Programming Mode:

1. Press both the [✻] and [#] keys at the same time, within 50 seconds after power is applied to the Control or from

exiting Programming mode, OR

2. After power-up, enter the Installer Code (4112) + 800 (This method disabled if Program mode is exited using ✻98.)

to enter Expert Programming mode or Installer Code (4112) + 888 to enter Voice Prompt Programming

mode.

Notes: 1. If a different Installer Code has been programmed, use that code to enter the Programming mode. Once you have entered the

Program mode, data field ✻20 (the first data field in the system) will be displayed and both keypad LEDs will flash.

2. Entering Programming mode may take up to 18 seconds if the 5842 Wireless Dialer has been enabled. The system will display

“ - - “ until the Lynx enters Programming mode.

Programming a Data Field

1. Press [✻] + Field No. (for example, ✻21), followed by the required entry.

2. When you have completely programmed a data field, the keypad will “beep” three times and then automatically

display the next data field in sequence. To go to a different field, press [✻] plus the desired field number.

3. If the number of digits that will be entered in a data field is less than the maximum number of digits available (e.g.

phone number field), enter the desired data, then press [✻] to advance to the next data field.

4. If a nonexistent field has been entered, the keypad will display “EE”. Simply re-enter [✻] plus a valid field number.

To view a data field without making changes: Enter [#] + Field No. Data will be displayed for that field.

To delete an entry in a field: Enter [✻] + Field No. + [✻]. (Applies only to fields ✻40–✻44, ✻88 and ✻94).

Interactive Mode Programming (✻56, ✻80, ✻81, ✻83, ✻84, ✻85)

Press [✻] + interactive mode No. (for example, ✻56). The keypad will display the first of a series of prompts.

A detailed procedure (with displays of prompts) is provided in later sections of this manual.

Interactive Mode

Used to Program

Zone characteristics, report codes, and serial numbers

Powerline Carrier Devices

Zone Lists for powerline carrier activation

5800 Series transmitter serial numbers

Voice descriptors for each zone

56 Enhanced Zone Programming Mode

✻

✻80 Device Programming Menu Mode

✻81 Zone List Menu Mode

83 Enhanced Sequential Mode

✻

✻84 Assign Zone Voice Descriptors

✻85 Record Custom Voice Descriptors

Up to 5 custom voice descriptors for zones

Loading Factory Defaults

To load the factory defaults, enter the Programming mode, press ✻97, then press number 1, 2, 3, or 4 to select from

default tables 1-4 at the back of this manual, or press “0” if you are not selecting a default table.

If a default table is loaded, any data that has already been programmed into the system will be changed according to

the default table selected!

✻96 resets all subscriber account numbers and CSID in preparation for an initial download.

Exiting Program Mode

✻98 inhibits re-entry into the Expert or Voice Prompt Programming modes using the Installer Code.

✻99 allows re-entry into the Expert Program mode using Installer Code (4112) + 800 or into the Voice Prompt

Programming mode using Installer Code (4112) + 888.

Note: After exiting program mode (or upon power-up), the system takes up to a minute to reset. To bypass the reset delay, press [#] + [0].

–14–

Download from Www.Somanuals.com. All Manuals Search And Download.

Zone Response Type Definitions

General Information

During programming, you must assign a zone type to each zone, which defines the way in which the system

responds to faults in that zone. Zone types are defined below.

Zone type 00 is used to program a zone that is not used.

Type 00

Zone Not Used

Zone type 01 is usually assigned to sensors or contacts on primary entry and exit

doors.

Zone Characteristics:

Type 01

Entry/Exit Burglary #1

•

Entry delay #1 is programmable from 0-99 seconds (field ✻35).

Exit delay is independently programmable from 0-99 seconds (field ✻34).

Exit and entry delays when armed in AWAY or STAY mode.

No entry delay when armed in STAY NO DELAY or AWAY NO DELAY mode.

Exit delay regardless of the arming mode selected.

01000-017-V0

Zone type 02 is usually assigned to sensors or contacts on which secondary entry and

exit doors that might be further from the keypad (typically used for a garage, loading

dock, or basement door).

Type 02

Entry/Exit Burglary #2

Zone Characteristics:

•

Entry delay #2 is programmable from 0-99 seconds (field ✻36).

Exit delay is independently programmable from 0-99 seconds (field ✻34).

Secondary entry delay, if armed in the AWAY or STAY mode.

No entry delay when armed in the STAY NO DELAY or AWAY NO DELAY mode.

Exit delay begins regardless of the arming mode selected.

01000-017-V0

Zone type 03 is usually assigned to all sensors or contacts on exterior doors and

windows. Zone Characteristics:

Type 03

Perimeter

Burglary

•

Instant alarm, when armed in AWAY, STAY, STAY NO DELAY, or AWAY NO

DELAY mode.

01000-018-V0

Zone type 04 is usually assigned to a zone covering an entry area (i.e.: foyer, lobby, or

hallway) that one must pass upon entry (after faulting the entry/exit zone) to reach

the keypad. It provides an instant alarm if the entry/exit zone is not violated first,

and protects an area in the event an intruder has hidden on the premises before the

system is armed, or gains access to the premises through an unprotected area.

Type 04

Interior, Follower

Zone Characteristics:

•

Delayed alarm (using the programmed entry/exit time) if entry/exit (types 01 or

02) or interior-with-delay (type 10) zone is faulted first.

5890 / 5890PI

01000-019-V1

•

Instant alarm in all other situations.

Active when armed in AWAY or AWAY NO DELAY mode.

Bypassed automatically when armed in STAY or STAY NO DELAY mode.

Zone type 05 is usually assigned to a zone that contains foil-protected doors or

windows or covers a sensitive area (i.e.: stock room, drug supply room, etc.) It can also

be used on a sensor or contact in an area where immediate notification of an entry is

desired.

Type 05

Trouble by Day/

Alarm by Night

Zone Characteristics:

•

Instant alarm, when armed in AWAY, STAY, STAY NO DELAY, or AWAY NO

DELAY (night) mode.

•

Provides a latched trouble sounding from the keypad and, if desired, a central

station report during the disarmed state (day).

Zone type 06 is usually assigned to a zone containing an Emergency

button (silent emergency).

Zone Characteristics:

• Sends a report to the central station but provides no keypad display or

sounding.

Type 06

24-hour

Silent Alarm

–15–

Download from Www.Somanuals.com. All Manuals Search And Download.

Zone Response Type Definitions

Type 07

Zone type 07 is usually assigned to a zone containing an Emergency

button (audible emergency).

Zone Characteristics:

• Sends a report to the central station, and provides alarm sounds

externally and at the keypad.

24-hour

Audible

Alarm

Zone type 08 is usually assigned to a zone containing a button for use

in personal emergencies or to a zone containing monitoring devices

(i.e.: water or temperature sensors, etc.).

Type 08

24-hour

Auxiliary Alarm

Zone Characteristics:

• Sends a report to the central station and provides an alarm sound at

the keypad. (No bell output is provided and there is no keypad

timeout.)

Zone type 09 can be assigned to any wireless zone used as a

fire zone. This zone type is always active and cannot be

bypassed.

Type 09

Supervised

Fire

5806/5807/5808

01000-020-V0

Zone Characteristics:

• Bell output will pulse when this zone type is alarmed.

Zone type 10 is bypassed when the panel is armed in the STAY or STAY

NO DELAY mode.

Zone Characteristics:

Type 10

Interior w/Delay

• Entry delay #1 (with programmed entry time) when armed in the

AWAY mode.

• Entry delay begins whenever sensors in this zone are violated,

regardless of whether an entry/exit delay zone was tripped first.

• No entry delay when armed in the AWAY NO DELAY mode.

• Exit delay regardless of the arming mode selected.

Zone type 20 is a special-purpose zone type used with 5800 Series

wireless pushbutton units.

Zone Characteristics:

Type 20

Arm–Stay

• Exit delay regardless of the arming mode selected.

• System is armed in the STAY mode when the zone is activated.

• Zone number is sent to the central station as a user number when

arming or disarming.

Zone type 21 is a special-purpose zone type used with 5800 Series

wireless pushbutton units.

Zone Characteristics:

Type 21

Arm–Away

• System is armed in the AWAY mode when the zone is activated.

• Zone number is sent to the central station as a user number when

arming or disarming.

Zone type 22 is a special-purpose zone type used with 5800 series

wireless pushbutton.

Zone Characteristics:

Type 22

Disarm

• Disarms the system when the zone is activated.

Zone type 23 can be used on a zone when a Powerline Carrier Device

(e.g., X-10) action is desired, but with no accompanying alarm (e.g.,

front door light).

Type 23

No Alarm Response

Zone type 24 is usually assigned sensors or contacts on exterior doors

and windows where bells and/or sirens are NOT desired.

Zone Characteristics:

Type 24

Silent Burglary

• Instant alarm, with NO audible indication when is armed in the

AWAY, STAY, STAY NO DELAY, or AWAY NO DELAY mode.

• Report sent to the central station.

Note: Keypad beeps if the zone is faulted when system is disarmed and Chime

mode is on.

–16–

Download from Www.Somanuals.com. All Manuals Search And Download.

Data Field Descriptions

Defaults (where applicable) are Indicated in Text.

The following pages list all data fields in this Control (in numerical order). Use the blank programming form

to record the data for this installation. Note that both keypad LEDs flash while in Programming mode.

Note: Entering a number other than the one specified will give unpredictable results.

The Installer Code is used to enter the 4-digit Master Security Code. See

"Master Code" in the System Operation section for procedure.

Installer Code

✻

Enter 4 digits, 0-9

If enabled, security code is not required to arm the system. The user

simply presses and holds down the AWAY or STAY key to arm.

Quick Arm Enable

0 = do not allow quick arm

1 = allow quick arm

✻21

This option allows the choice of either always backlighting the keypad or

turning the backlighting off after 10 seconds of keypad inactivity.

Keypad Backlight Timeout

0 = no timeout; always backlight keys

1 = turn backlighting off after inactivity

✻22

All zones bypassed by this function will be displayed after the bypass is

initiated.

Forced Bypass

✻23

0 = no forced bypass

1 = provide automatic bypass of all open (faulted)

Note: UL installations: must be 0 (no forced bypass)

zones

The House ID identifies receivers and wireless keypads.

RF House ID Code

✻24

If a 5827 Wireless Keypad or 5804BD/5804BDV Transmitter is to be

00 = disable all wireless keypad usage

used, a House ID Code MUST be entered, and the keypad should be set

01-31 = House ID

to the same ID.

Powerline Carrier Devices require a House ID. This field identifies this

House ID to the Control. The Powerline Carrier Devices are

programmed in field ✻80.

Powerline Carrier Device (X-10) House ID

✻25

0 = A

1 = B

2 = C

3 = D

4 = E

5 = F

6 = G

7 = H

8 = I

# + 12 = M

# + 13 = N

9 = J

# + 10 = K # + 14 = O

# + 11 = L # + 15 = P

This option allows the installer to define the specific zones intended to

chime when faulted while the system is in Chime mode. If enabled, these

zones are defined in zone list 3 (see ✻81 Zone List Menu Mode).

Chime by Zone

0 = no (chimes on fault of any entry/exit or perimeter

zone when Chime mode is activated

✻26

1 = yes (chimes on fault of those zones assigned to

Zone List 3 when Chime mode on)

Refer to the User’s Manual for setting the clock time and date.

Enter # + 10 for 10, # + 11 for 11, and # + 12 for 12.

Real Time Clock Display

0 = do not display the time

1 = display the time

✻27

✻29

Daylight Savings Time Start/End Month

0, 0 = no daylight saving time used

1-12 = start month and end month

Enter the appropriate start and end weekend of the month.

Daylight Savings Time Start/End Week

✻30

✻31

0 = disable

4 = fourth weekend

1 = first weekend of month 5 = last weekend

2 = second weekend

3 = third weekend

6 = next to last

7 = 3^rdfrom last

UL installations: must be 0 (no limit)

Single Alarm Sounding Per Zone

(per armed period)

0 = no limit on alarm sounding per zone

1 = limit alarm sounding to once per arming period for

This field applies only to burglary zones (zone response types 1-5, 10),

and affects long range radio reporting but does not affect central station

reporting.

a given zone

Note: This field applies only to the bell and does not affect keypad

LYNXR/LYNXR24 - Applies to Long Range Radio Output if “0”

is selected in field ✻91

sounds.

LYNXR-EN - Applies to Long Range Radio Output if Long Range

Radio is connected to the Trigger Single (Neg.) terminal #8.

This Control complies with NFPA requirements for temporal pulse

sounding of fire notification appliances.

Temporal pulse sounding for a fire alarm consists of the following:

3 pulses – pause – 3 pulses – pause – 3 pulses. . .

Fire Sounder Timeout

✻32

0 = yes, fire sounder timeout after time programmed in

field ✻33

1 = no fire sounder timeout; continue sounding until

manually turned off

This field determines whether the external sounder will shut off after

time allowed, or continue until manually turned off.

UL installations: must be set for a minimum of 4 min (option 1)

Alarm Bell Timeout

✻33

✻34

0 = No timeout

1 = 4 min

2 = 8 min

4 = 16 min

3 = 12 min

The system will wait the time entered before sounding an alarm if the

exit door is left open after the system has been armed.

UL installations: must be set for a maximum of 60 seconds

Exit Delay

00-99 = exit delay time in seconds

–17–

Download from Www.Somanuals.com. All Manuals Search And Download.

Data Field Descriptions

The system will wait the time entered before sounding alarm upon entering

if system is not disarmed. UL installations: must be set for a maximum of

45 seconds

Entry Delay 01

00-99 = entry delay time in seconds.

✻35

The system will wait the time entered before sounding alarm upon

entering. UL installations: must be set for a maximum of 45 seconds

Entry Delay 02

✻36

✻37

00-99 = entry delay time in seconds.

Exit Warning: Sound consists of slow continuous beeps until last 5 seconds,

when it changes to fast beeps. The warning sound will end at the

termination of exit delay.

Audible Exit Warning/Quick Exit

Exit Warning

Quick Exit

0 = no exit warning

sound

1 = provide exit

warning sound

0 = no quick

exit

1 = allow quick

exit

Quick Exit: If enabled, user can restart the exit delay time after arming in

STAY mode by entering the user code and pressing the STAY key, or by

pressing the STAY key if Quick Arm is enabled. This avoids having the

user disarm then re-arm the system after allowing someone to enter or exit

when armed AWAY

Confirmation of arming is provided by a 1/2 second external sounder “ding”

that sounds when closing report is sent, or at the end of exit delay.

Confirmation of Arming Ding

0 = no ding

1 = confirmation ding after arming system

2 = confirmation ding after arming from RF button or

RF keypad only

✻38

✻39

If Option 2 is selected the external sounder “ding” occurs immediately after

the system receives the RF transmission.

When the system powers up armed, an alarm will occur 1 minute after

arming if a zone is faulted, and any bypassed zones will be unbypassed.

Note: If the previous state was armed AWAY or STAY, the system will not

respond to sensor changes for 1 minute, which allows time for sensors such

as PIRs to stabilize. UL installations: must be 1 (power up in previous

state)

Power Up In Previous State

0 = always power up in a disarmed state

1 = assume the system status prior to power-down

✻

DIALER PROGRAMMING ( 40– 50)

✻

* ;

Fields 40, 41, 42: Enter up to the number of digits shown. Enter 0–9, # + 11 for ‘ ’ # + 12 for ‘#’; # + 13 for a pause

(2 seconds)

NOTE: Whenever AAV is used, primary (field ✻41) and secondary (field ✻42) phone numbers should be preceded with the call waiting

disable command. Otherwise, there is the possibility of connection of the third party to LYNX during AAV mode.

✻

If fewer than 6 digits need to be entered, exit by pressing [ ]. To clear

PABX Access Code

✻40

✻41

✻

entries from field, press 40

Enter up to 6 digits if PABX is needed to access an

outside line.

✻

If fewer than 20 digits entered, exit by pressing [ ]. To clear entries from

Primary Phone No.

Enter up to 20 digits.

✻

field, press 41

Note: Backup reporting (8 attempts are made to the secondary phone

number if no kissoff is received after 8 attempts to the primary

number) is automatic only if there is a secondary phone number

✻

(field 42).

✻

If fewer than 24 digits entered, exit by pressing [ ]. To clear entries from

Secondary Phone No.

Enter up to 24 digits.

✻42

✻

field, press 42 . See backup reporting note for field 41. If using the

paging feature, enter the pager phone number here.

✻

All four digits of the Subscriber Account number must be entered in Fields 43 and 44. If ten digit format is

✻

selected in 48 (option 5), all ten digits of the Subscriber Account number must be entered.

✻

Fields 43 and 44:

✻

Enter [ ] as the fourth digit if a 3-digit account number (for 3+1 dialer reporting format) is used. Enter 0 as the first

✻

digit of a 4-digit account number for Nos. 0000–0999. Enter [ ] as the fifth digit if a 4-digit account number (for 3+1,

✻

✻ or ✻

✻

CID®) is used. Exit field by pressing [ ] if only 3 digits are used. To clear entries from field, press 43

44 . See

blank Programming Form for examples of account number entries. If using the paging feature, do not enter a leading 0

in the subscriber account number, and do not use digits A-F anywhere in the number. Some paging systems provide

voice mail capability, which is activated by a leading 0 in the message. Enter digits 0–9; # +11=B; # +12=C; # +13=D; #

+14=E; or # +15=F.

Enter the primary subscriber account number.

Primary Subs Account No.

Enter a four or ten digit account number.

✻43

✻

To clear entries from field, press 43

Enter the secondary subscriber account number.

Secondary Subs Account No.

Enter a four or ten digit account number.

✻44

✻

To clear entries from field, press 44

–18–

Download from Www.Somanuals.com. All Manuals Search And Download.

Data Field Descriptions

Field 46: Enter up to 24 digits. Do not fill unused spaces. Enter 0-9, #+11 for ‘*’; #+12 for’#’; #+13 for a pause (2 seconds).

This option allows the user to schedule a time driven message. When

“Follow Me Reminder” Phone Number

Enter up to 24 digits.

✻46

activated the system will dial the phone number programmed and deliver a

voice message (custom words 72, 73 and 74). This option is only supported

✻

when the pager or follow me feature is enabled in field 49 (option 6-9 or

10-13).

If using the Follow Me Reminder feature, enter the phone number here. If

✻

fewer than 24 digits are entered, exit by pressing [ ]. To clear entries from

✻

the field press 46

The telephone message can be terminated (acknowledged) by pressing any

key on the telephone keypad. Pressing any key on the local LYNXR keypad

will terminate (acknowledge) both the follow me and the local reminder

announcements.

Note: The follow me reminder announcement will be terminated if any

other event requires the system to dial out or if and audible alarm

has occurred.

This option is used to enter the correct type of phone dialing (pulse or tone),

and to select the correct WATS line option for the Central Station. For

LYNXR-EN this option is used to activate the speaker phone option.

Phone System Select

✻47

✻48

Note: For LYNXR/LYNXR24 only options 0, 1, 2, and 3

are applicable. For LYNXR-EN all options apply.

Central

Station

Dialing Mode

Note: If using pulse dialing, you must enter the numbers slowly in order to

allow the pulse dialer time to operate.

Pulse

Tone

Pulse

Tone

No WATS 0 = No

Speaker

1 = No

Speaker

Phone

4 = With

Speaker

Phone

5 = With

Speaker

Phone

WATS

2 = No

Speaker

Phone

3 = No

Speaker

Phone

6 = With

Speaker

Phone

7 = With

Speaker

Phone

✻

Enter as the 4th digit of 43 through 44, if 3+1 dialer reporting is to be

used. (For an explanation of these formats, see the System Communication

section of this manual.)

Report Format for Primary/Secondary

Primary

See choices below

Secondary

See choices below

Notes: (1) The maximum number of alarm and alarm restore reports

✻

during one armed period is determined by field 92.

0 = 3+1; 4+1 ADEMCO Low Speed Standard

1 = 3+1; 4+1 Radionics Standard

2 = 4+2 ADEMCO Low Speed Standard

3 = 4+2 Radionics Standard

5 = ADEMCO Contact ID® Reporting with 10-digit

subscriber account number

(2) If Option 5 is selected a 10-digit account number must be

✻

entered in Fields 43 or 44.

(3) Option 5 or 7 (ADEMCO Contact ID® Reporting) must be

selected for AVM.

(4) Option 5 or 7 (ADEMCO Contact ID® Reporting) must be

selected if installing the 5842 Wireless Dialer.

6 = 4+2 ADEMCO Express

7 = ADEMCO Contact ID® Reporting with 7-digit

subscriber account number

8 = 3+1; 4+1 ADEMCO Low Speed Expanded

9 = 3+1; 4+1 Radionics Expanded

This field is used to select a reporting option as follows:

Enter: 0 - 5 when reporting to telephone receivers.

6 - 9 when reporting to a pager is desired.

Split/Dual Reporting

✻49

To Primary

To Secondary

0 = All reports

None, unless primary

fails, then all

Others

Open/Close, Test

All

10 - 13 when reporting to an auxiliary telephone receiver.

Pager Report Format

1 = Alarms, Restore, Cancel

2 = All except Open/Close, Test

3 = Alarms, Restore, Cancel

4 = All except Open/Close, Test

5 = All reports

Options 6-9 send reports to the primary phone number, in a format defined

✻

in Field 48, and send reports to a pager, which has its phone number

✻

entered as the secondary phone number in Field 42. The pager report is a

7-digit code, with optional 16-digit prefix, in the following format:

AAAAAAAAAAAAAAAA-EEE–00NN where:

AAA = Optional 16 digits for PIN number, etc. See Field 88 for full

To Primary

To Paging Number

✻

‡

description of these characters.

EEE = 3-digit Event Code as follows:

911 = Alarm (NN = zone number)

101 = Open, system disarmed (NN = user no.)

102 = Close, system armed (NN = user no.)

811 = Trouble (NN = zone no.)

00 = Always displayed before 2-digit user/zone no.

NN = 2-digit user number or zone number, depending on the type of

event (EEE) that occurred. NN=00 indicates AC loss, system low

battery, or low battery in 5827.

6 = All reports except Open/Close

Alarms, Open/Close

Troubles

7 = All reports

8 = All reports

Alarms, Troubles

‡

Alarms, Open/Close

Troubles

‡

9 = All reports except Open/Close

To Primary

Open/Close

To Follow Me System

Phone Number

‡

10=All reports except Open/Close

Alarms, Open/Close

Troubles

Follow Me System Report Format

Options 10-13 send reports to the primary phone number, in a format

11 = All reports

12=All reports

Alarms, Troubles

✻

defined in Field 48, and sends voice message to the secondary phone

‡

✻

number entered in Field 42.

Alarms, Open/Close

Troubles

The message is a repeatable system status announcement. If the manual

‡

✻

paging option has been programmed in Field 87, the message will repeat

13=All reports except Open/Close

‡

Open/Close

“system, system…..”.

Will report Users 0, 5-8, and, if using wireless button-type

devices, will report the zone number of the arm or disarm

button 26-33. All other zones and users are not reported.

The message can be terminated by pressing any key on the telephone

keypad.

–19–

Download from Www.Somanuals.com. All Manuals Search And Download.

Data Field Descriptions

If enabled, provides communication delay to the central station and allows

the subscriber time to avoid a false alarm transmission. Delay does not

apply to zone type 6, 7, 8, and 9 alarms, which are always sent as soon as

they occur. UL installations: must be 0 (no delay)

15-Second Dialer Delay (Burglary)

✻50

0 = no dialer delay

1 = provide 15-second delay of burglary alarm report

when armed away

✻

Test report code entered in field 64 is sent.

Periodic Test Report

✻51

0 = no test report

2 = weekly

1 = once every 24 hrs 3 = once every 30 days

This is the time to first report from programming or downloading.

First test Report Offset

✻52

0 = 24 hrs after exit program mode or download

1 = 6 hours after exit program mode or download

2 = 12 hrs after exit program mode or download

3 = 18 hrs after exit program mode or download

Select 0 for all other formats.

Sescoa/Radionics Select

0 = Radionics (0–9, B–F reporting)

1 = SESCOA (0–9 only reporting)

✻53

If enabled, notifies the central station if an end user is not operating their

security system by sending a System Inactivity report 654. The report will

be sent only to the Primary phone number and only if Contact ID® format

was selected.

Lack of Usage Notification

✻

0 = Disabled

1 = 1 day

4 = 90 days

5 = 180 days

6 = 365 days

2 = 7 days

3 = 27 days

✻

Note: The report will follow the 49 = 0 rules, no matter which selection

✻

was made in 49.

Note: There will be no local annunciation indicating that

this report has been sent to the Central Station.

For Event Logging, Option 2 must be selected.

RF Jam Detection

✻58

0 = no jam detection

If the control detects an RF jam condition, a “FAULT” message appears for

zone 90. The Contact ID® code for RF Jam is 344.

Note: This feature cannot be used in conjunction with the 5827 wireless

keypad.

1 = RF jam detection with event logging, but no

central station report

2 = RF jam detection with event logging and with

central station report (if trouble/restore report is

enabled in fields ✻60, ✻71)

✻

SYSTEM STATUS AND RESTORE REPORT CODES PROGRAMMING ( 59 – 76, & 89)

✻

Program Report Codes using the interactive 56 Enhanced Zone Programming Mode, or codes can be entered in data

✻

fields 59- 76, 89. The following is a set of guidelines when programming report codes. The actual report code digits

that you enter depend upon the particular installation, and should be in agreement with you and the central station

office receiving the signals.

With a 3+1 or 4+1 Standard Format: Enter a code in the first box: 1–9, A, B, C, D, E, or F. Enter "#+10" for A

(reports a “0” on some receivers), "#+11" for B, "#+12" for C, "#+13" for D, "#+14" for E, "#+15" for F. Entering "0" in the

first box will disable a report. Entering "0" in the second box results in automatic advance to the next field.

With an Expanded or 4+2 Format: Enter codes in both boxes (1st and 2nd digits) for 1–9, or A–F, as described above.

Entering "0" in the first box will disable a report. Entering "0" in the second box will eliminate the expanded message for

that report.

With ADEMCO Contact ID® Reporting: Enter a digit in the first box to enable the zone to report. Use a different

digit for each zone until you have used up available digits. If the number of zones exceeds the number of available

digits, begin with digit 1 again. This is an "enabling" code only and is not the actual code sent to the central station

office. Entries in the second boxes will be ignored. For system status (non-alarm) codes, enter a “1” in the first box for all

the system conditions you want to send to the central station. A "0" in the first box disables the report.

–20–

Download from Www.Somanuals.com. All Manuals Search And Download.

Data Field Descriptions

✻

SYSTEM STATUS REPORT CODES ( 59– 68)

If the system is armed and an entry/exit or interior zone is still open

after the exit delay time has expired, an alarm will sound at the

keypad and external sounder. If the system is disarmed before the

end of the entry delay that immediately follows, the alarm sounding

will stop and no message will be sent to the central station. The

keypad will display “CA (CANCELED ALARM).”

Exit Error Report Code

(See notes above)

✻59

If the system is not disarmed before the end of the entry delay

mentioned above, and an entry/exit or interior zone is still open, an

“exit alarm” message will be sent to the central station if an Exit

Error report code is selected in this field. The keypad will display

“EA (EXIT ALARM),” and the alarm sounding will continue until

the system is disarmed (or timeout occurs).

An Exit Alarm condition will also result if a fault occurs in an exit or

interior zone within 2 minutes following the end of the exit delay,

and an “Exit Alarm” message will be sent to the central station.

If Contact ID® format has been programmed, the message will

contain the zone number and error code 374 (Trouble–Exit Error). If

4+2 format is used, the digit entered in this field will be sent

followed by the second digit of the programmed alarm code for that

zone. If 3+1 or 4+1 format is used, only the digit entered in this field

will be sent. This message will go to the primary phone no. Under

any of these conditions, no restore message will be sent.

If “0” is entered in this field, no special message will be sent, only

the regular alarm and alarm restore code for the zone.

This will be sent if a zone goes into trouble.

Trouble Report Code

✻60

(See notes above)

This will be sent when a zone is manually bypassed.

Bypass Report Code

(See notes above)

✻61

Timing of this report is random with up to a 4-hour delay. If AC

restores before the report goes out, there is no AC restore report.

AC Loss Report Code

(See notes above)

✻62

This will be sent when a low battery condition exists in the system’s

standby battery.

Low Battery Report Code

(See notes above)

✻63

This is sent periodically to test that the communicator and phone

lines are operational (frequency of report is selected in field 51).

Test Report Code

(See notes above)

✻

✻64

This is sent upon disarming of the system. 2nd digit = user number,

if expanded or 4+2 reporting is selected.

Open Report Code

✻65

(See notes above)

This option allows for independent programming of AWAY and

STAY reports. 2nd digit of report is user number if expanded or 4+2

reporting is selected.

Arm AWAY/STAY Report Code

(See notes above)

✻66

NOTE: OPEN reports are not sent if the associated closing report is

not enabled.

This is sent in the event that a wireless transmitter low battery

condition exists.

RF transmitter Low Batt. Report Code

(See notes above)

Cancel Report Code

(See notes above)

✻67

This is sent upon disarming of the system after an alarm condition

was reported.

✻68

✻

RESTORE REPORT CODES ( 70– 76)

Sent when the zone that caused an alarm is restored to its non-

faulted condition. 2nd digit is automatically sent as the 2nd digit of

the zone alarm report code programmed in field 56, if expanded or

Alarm Restore Report Code, 1st Digit

(See notes above)

✻70

✻

4+2 reporting is selected.

Sent when a trouble in a zone is restored.

Trouble Restore Report Code

(See notes above)

✻71

Sent when a zone that has been bypassed is unbypassed.

Sent when AC power has been restored after an AC power outage.

Sent when a system low battery condition is restored to normal.

Bypass Restore Report Code

(See notes above)

✻72

AC Restore Report Code

✻73

(See notes above)

Low Battery Restore Report Code

(See notes above)

✻74

–21–

Download from Www.Somanuals.com. All Manuals Search And Download.

Data Field Descriptions

✻

RESTORE REPORT CODES ( 70– 76) Continued

Sent when a transmitter that previously sent in a “low battery” message

has sent a message indicating it no longer has a low battery condition.

RF Transmitter Low Batt. Restore Code

(See notes above)

✻75

Sent when the test mode is exited. A restore code entered here will cause

a restore message to be sent when Test mode is exited.

Test Restore Report Code

(See notes above)

✻76

If “0” is entered, user can define a macro function for the AUX key. See

user manual for description of the use of this key.

AUX Function/1-Button Paging

✻87

0 = Aux key performs defined function (macro)

✻

If “1” is entered, you must also select an option in field 49. The options

1 = Aux key sends predefined message to pager or a

voice message to Follow Me system phone

number

are 6-9 for the pager or 10-13 for the follow me system announcement.

The actual pager message is 999-9999. Note that the hyphen may not be

displayed, depending on the pager service. The manual follow me system

announcement is a repeatable “System, System…..”.

Note: A macro cannot be run from the Test mode.

If entered, these digits will appear in front of the 7-digit pager message

sent by the control (either upon a system event or upon pressing the AUX

key [if programmed for paging]), and during latch key report (if enabled

during scheduling). These digits can consist of a PIN number, account

number, pauses or special digits needed by the pager (these types of

characters are not displayed), or any other characters the user chooses

that will be displayed (eg., using a character code to distinguish between

control panel messages and other pager messages).

Pager Characters

✻88

Enter up to 16 digits that will appear in front of the 7-

digit pager message.

Enter [#] + [11] for “*”

Enter [#] + [12] for “#”

Enter [#] + [13] for 2-second pause

NOTES: Verify that the pager supports [*] and [#]

characters before using them. Some pagers

require an additional delay [pause] in order to

receive the entire message.

✻

You do not need to fill all 16 digits. Press [ ] + next field number to exit

the field. To clear the field, press 88

✻

✻.

✻

See field 87 to select the AUX key Paging feature. See field 49, which

must have an option 6-9 selected to enable paging messages, for

description of the pager message.

✻

If an Event Logging selection is made in field 90, a message can be sent

Event Log 80% Full Report Code

(See notes above)

✻89

to the central station receiver when the log is 80% full. If the log becomes

full, a new message will overwrite the oldest message in the log.

Note: All control and readout from the log, aside from the selection made

✻

by the installer in field 90, is accomplished via the downloader.

Example: To select “Alarm/Alarm Restore” and “Open/Close,” enter 9 (1 +

8); to select all events, enter #15.

Event Logging Options

✻90

0 = No event logging

1 = log Alarm/Alarm Restore

Default “3” = alarm/alarm restore (1) plus trouble/trouble restore (2).

The system has the ability to record various events in a history log (84-

event capacity). The types of events to be logged can be selected as

indicated. At any time, the downloader operator can then upload the log

and view or print out all or selected categories of the log. The log can also

be cleared by the download operator.

2 = log Trouble/Trouble Restore

4 = log Bypass/Bypass Restore

8 = log Open/Close

x = log combination of events (add value of entries)

The display/printout at the central station will show the date, time, event,

and description of the occurrences.

Note: System messages are logged when any non-zero selection is made.

–22–

Download from Www.Somanuals.com. All Manuals Search And Download.

Data Field Descriptions

The features programmed in Field 91 differ between LYNXR models. Ensure you use the correct option

for the model you are installing!

✻

✻91

For LYNXR/LYNXR24, this option is used to enable the Long Range

LYNXR/LYNXR24

Long Range Radio/Alarm Audio

Verification (AAV) Trigger/Remote Phone

Control

0 = long range radio trigger only

1 = AAV and remote phone control

2 = long range radio trigger and remote phone control

4 = AAV only

Radio, Alarm Audio Verification and/or Remote Phone Control options.

If Long Range Radio (0) is selected, trigger output (terminal screw #8)

will generate a steady signal for burglary alarm (a single 3 to 4-second

pulse for all types of silent alarms) or a temporal signal for fire alarm.

(Refer to Long Range Radio Installation Instructions for appropriate

wiring.) Alarm Audio Verification requires the installation of the

LYNX-AVM. (Refer to LYNX-AVM Installation Instructions)

Notes: (1) If Long Range Radio is being connected, Alarm Audio

Verification cannot be used.

(2) In order to activate the remote phone control feature and

Notes:

For UL installations Alarm Audio Verification

cannot be used. Alarm Audio Verification will only

function when Contact ID® is selected.

defeat an answering machine, ensure that the correct ring

✻

detection count (“15”) has been programmed in field 95.

(3) Remote phone session will be terminated if a report must

be sent.

(4) A Long Range Radio cannot be connected f AAV is selected.

(5) Alarm Audio Verification will only function when Contact

ID® is selected and cannot be used for UL installations.

(6) If an alarm will be reported to primary and secondary

phone numbers, AAV can only function via the secondary

number.

✻

(7) If an alarm will be reported to a pager (6-8 in field 49), or

✻

to follow me phone number (10-12 in field 49) AAV

cannot be used.

For LYNXR-EN, this option is used to enable the Audio Alarm

Verification and/or the Remote Phone Control features.

Notes: (1) In order to activate the Remote Phone Control feature and

defeat an answering machine, ensure that the correct ring

detection count (“15”) has been programmed in field ✻95.

(2) Remote phone session will be terminated if a report must

be sent.

LYNXR-EN

Alarm Audio Verification (AAV)/Remote

Phone Control

0 = none

1 = AAV and remote phone control

2 = remote phone control only

4 = AAV only

(3) Alarm Audio Verification will only function when Contact

ID® is selected. AAV cannot be used for UL installations.

(4) If an alarm will be reported to primary and secondary

phone numbers, AAV can only function via the secondary

number.

Notes: (1) For UL installations alarm audio verification cannot

be used. Alarm Audio Verification will only function

when Contact ID® is selected.

✻

(5) If an alarm will be reported to a pager (6-8 in field 49), or

(2) AAV and Remote Phone Control features can only

be used if the central station or remote phone

supports DTMF commands.

✻

to follow me phone number (10-12 in field 49) AAV

cannot be used.

(3) No programming is required if connecting an

ALARMNET 7845C device because the option is

always enabled.

This option can be used to limit the number of messages (alarm &

alarm restore reports) sent to the central station in an armed period.

UL installations: must be 1 (unlimited reports)

Number of Reports In Armed Period

0 = reports limited to a total of 10

1 = unlimited number of reports

Flexible Callback

0 = no flexible callback

1 = last digit flexible

2 = last 2 digits flexible

3 = last 3 digits flexible

✻92

✻93

If enabled, the control will ignore the last 1, 2, or 3 digits of the

programmed callback number (field ✻94) during a single download

session. This allows the download operator to temporarily change the

callback phone number by the number of digits selected, which allows

the control to call back similar, but different numbers during a single

session. For example, if downloading to a large number of controls, the

operator can command the controls to call back phone numbers 555-

1111, 555-1112, 555-1113, etc., thus spreading the communications

among several computers.

✻

DOWNLOAD INFORMATION ( 94, 95)

This is the phone number the control will use to call back the

downloading computer.

Download Call Back Phone Number

Enter up to 20 digits as follows: 0–9, # +11 for “*”, # +

12 for “#”, # + 13 for a pause.

✻94

✻

Do not fill unused spaces. End field by pressing . To clear entries

✻

from field, press 94

Enter “15” to select defeat answering machine mode. If an answering

machine is on the premises, you need to dial the premises and hang up

on the first ring. Wait at least five (5) seconds (but no more than 22

seconds) and dial the premises phone number again. The control will

pick up and announce “SYSTEM ENTER CODE” every three seconds.

Ring Detection Count For Downloading/

Remote Phone Control

0 = disable station initiated download and remote

✻95

phone

1-14 = number of rings before control picks up phone

Note: To enter a number higher than 9 you must first press the [#] key.

line

15 = defeat answering machine

–23–

Download from Www.Somanuals.com. All Manuals Search And Download.

Data Field Descriptions

Other Programming Commands

✻

ENABLING THE WIRELESS DIALER

✻

Interactive menu mode used for enabling the 5842 Wireless Dialer. Refer to the 55 Enabling the

Wireless Dialer Mode section for procedure.

✻

ENHANCED ZONE PROGRAMMING MODE

✻

Interactive menu mode used for programming zone attributes and report codes. Refer to the 56

Enhanced Zone Programming Mode section for procedure.

DEVICE PROGRAMMING MENU MODE

Interactive menu mode for programming Powerline Carrier Devices. Refer to the 80 Device

Programming Menu Mode section for detailed procedure.

✻

ZONE LISTS FOR MENU MODE

Interactive menu mode for programming zone lists for Powerline Carrier Devices. Refer to the 81

Zone List Menu Mode section for detailed procedure.

✻

ENHANCED SEQUENTIAL MODE

Interactive menu mode used to enter RF transmitter serial numbers. Refer to the 83 Enhanced

Sequential Mode section for detailed procedure.

✻

ASSIGN ZONE VOICE DESCRIPTORS

Interactive menu mode used to assign descriptors to each zone. These descriptors will be announced

whenever the system announces an event involving a zone.

✻

RECORD CUSTOM VOICE DESCRIPTORS

Interactive menu mode used to record custom descriptors for use with each zone.

INITIALIZE DOWNLOAD ID AND SUBSCRIBER ACCT. NO. FOR

DOWNLOADING

✻

Pressing 96 initializes the system for downloading.

✻

SET ALL PROGRAM FIELDS TO 1 OF 4 SETS OF DEFAULT VALUES

See Default Tables at the end of this manual.

EXITS PROGRAMMING MODE

Prevents re-entry by: Installer Code + 8 + 0 + 0; allows re-entry only by Power-up, then [ ] and [#].

✻

EXITS PROGRAMMING MODE

✻

Allows re-entry to program mode by: Installer Code + 8 + 0 + 0; or by Power-up, then [ ] and [#].

–24–

Download from Www.Somanuals.com. All Manuals Search And Download.

✻

55 Enabling the 5842 Wireless Dialer

This is an interactive menu mode that is used to enable and program the 5842 Wireless Dialer. When

enabled, the 5842 will interface with the Lynx Control and serve as the system’s primary dialer. The 5842

receives and acknowledges RF messages from the control’s transceiver and, in response, sends reports to the

central station via the dialer. It also sends acknowledgements, supervisory and tamper RF transmissions to

the control. If the wireless dialer has tried unsuccessfully to send a report, the Lynx will attempt to report to

the Central Station via the on-board dialer (if it has been programmed for back-up reporting). The Back-up

reporting option must be selected for Follow-me, Pager and AAV operation (refer to field *49).

LYNX must be connected to the telephone line, if using the Back-up reporting option.

Wireless Dialer Setup

If the wireless dialer is enabled in Field ✻55, Lynx automatically sends the setup information to the wireless

dialer immediately after exiting the programming mode. Lynx will confirm that the 5842 wireless dialer has

successfully received the setup information by generating three beeps. If the setup information has not been

successfully received by the wireless dialer the Lynx will generate a single beep once per minute and “Fault

Zone 93” will be displayed. To prepare the dialer for setup refer to the Installation Instructions provided

with the 5842 Wireless Dialer.

Note: 1. It takes about 95 seconds for Lynx to transmit the setup information after power has been applied to the

control.

2. Entering Programming mode may take up to 18 seconds if the 5842 Wireless Dialer has been enabled. The

system will display “ - - “ until the Lynx enters Programming mode.

You must refer to these instructions or to the Programming Guide while programming the system because the keypad display

does not show prompt titles. Instead, prompts are indicated by a number/letter combination.

The prompts for ✻55 are as follows:

Enable Dialer....................................... for enabling the 5842 wireless dialer.

Enable Trouble/Supervisory Reports . for defining wireless dialer response to events.*

Response to Phone Line Failure......... for defining console sounder response (trouble/alarm) to a

phone line cut.

Enable Back-up Reporting.................. for enabling the Lynx as a backup dialer.

*The Contact ID® Event Codes for the reports associated with the 5842 wireless dialer include the following:

145

338

341

342

351

355

Wireless Dialer Tamper (Alarm)

Wireless Dialer Low Battery

Wireless Dialer Tamper (Trouble)

Wireless Dialer AC Loss (if supported by the 5842 Wireless Dialer being installed)

Wireless Dialer Phone Line Cut (if supported by the 5842 Wireless Dialer being installed)

(Zone 93) Wireless Dialer Loss of RF Supervision

(Zone 000) Interruption of RF Link reported by the 5842 Wireless Dialer

For additional information refer to the Contact ID® Event Codes table.

–25–

Download from Www.Somanuals.com. All Manuals Search And Download.

✻

55 Enabling the 5842 Wireless Dialer

While in Program mode, press

✻55 to enter Wireless Dialer Programming Feature.

The following explains the ✻55 prompts in detail. The left two columns identify the prompts and list the

available entries for each. The right-most column provides a further explanation of the entries.

Note: You may find it convenient to adjust the volume setting before entering the Programming Mode. This will allow you to clearly

hear feedback announcements or system beeps.

Enter [1] to enable the 5842 Wireless dialer. Press [✻] to advance to next

field.

Enable the wireless dialer

[✻] = continue

0 = disable

1 = enable

Enter [0] to exit mode. The prompt “55” blinks, indicating the mode is

inactive. Press [✻] + any field number to go to that field.

If selected, the following 5842 trouble reports will be enabled:

Enable trouble reports

•

Loss of RF link with 5842 Wireless Dialer

Tamper at 5842

Low Battery at 5842

AC loss at 5842 (if supported by the specific wireless dialer being

[✻] = continue

[#] = return to previous prompt

0 = disable

1 = enable

installed)

•

Line Cut at 5842 (if supported by the specific wireless dialer being

installed)

Enter [1] to enable 5842 Wireless Dialer trouble reports. Press [✻] to

advance to next field or [#} to return to the previous prompt.

Select the Lynx response to detection of a line cut at the 5842 Wireless

Dialer.

If the trouble sounder is enabled the system will sound a trouble event any

time the 5842 phone line is cut.

If the alarm sounder is enabled the system will a trouble by day or an

alarm at night in the event that the 5842 phone line is cut.

Response to phone line tamper

[✻] = continue

[#] = return to previous prompt

0 = enable trouble sounder

1 = enable alarm sounder

Enter [1] to select alarm or [0] to select trouble in the event of a 5842 line

cut. Press [✻] to advance to next field or [#} to return to the previous

prompt.

Note: If an X-10 device has been programmed to ZT05 or ZT07 and

*55 has been enabled, the device response will be dependent upon

the selection made in *55 Field "Ln".

Allows Lynx to do back-up reporting for the 5842 wireless dialer. Enter [1]

to enable back-up reporting. Refer to the 5842 Wireless Dialer Installation

guide for additional information.

Enable back-up reporting

[✻] = continue

[#] = return to previous prompt

0 = disable

Enter [0] to disable back-up reporting. Enter [#} to return to the previous

prompt.

1 = enable

Note: Lynx must be connected to the premises phone line via the 5842

Wireless Dialer.

–26–

Download from Www.Somanuals.com. All Manuals Search And Download.

✻

56 Enhanced Zone Programming Mode

This is an interactive menu mode that is used to program zone numbers, zone types, alarm and report codes,

and to identify the type of loop input device. This mode can also be used for entering 5800 Series transmitter

serial numbers.

Note: There are two methods for entering transmitter serial numbers. The first method is by using ✻56 Enhanced Zone Programming mode

(described below). The second method is by using ✻83 Enhanced Sequential Mode. Note that the ✻83 Enhanced Sequential Mode

requires that all zone information first be entered using ✻56 Enhanced Zone Programming mode.

You must refer to these instructions or to the Program Form while programming the system because the

keypad display does not show prompt titles. Instead, prompts are indicated by a number/letter combination.

The prompts for ✻56 are as follows:

A 01

Zone Number ----------------------- for entering the zone number

Zone Type---------------------------- for entering zone type

Report Code------------------------- for entering the zone’s report code

Input Type--------------------------- for entering the transmitter’s input type

Loop Number ----------------------- for entering the transmitter loop number

Delete Serial Number? ---------- for deleting existing serial number

Enroll Mode?------------------------ selects serial number enroll mode

Serial Number --------------------- for entering transmitter’s serial number

Voice Descriptor?------------------ selects voice descriptor mode

Descriptor 1------------------------- for entering first descriptor word

Descriptor 2------------------------- for entering second descriptor word

Descriptor 3------------------------- for entering third descriptor word

–27–

Download from Www.Somanuals.com. All Manuals Search And Download.

✻

56 Enhanced Zone Programming Mode

While in Program mode, press

✻56 to enter Zone Programming Menu Mode.

Refer to the zone assignment table for ✻56 on the separate programming form.

The following explains the ✻56 prompts in detail. The left two columns identify the prompts and list the

available entries for each. The right-most column provides a further explanation of the entries.

Note:

You may find it convenient to adjust the volume setting before entering the Programming Mode. This will allow you to clearly hear

feedback announcements or system beeps.

Enter the 2-digit zone number to be programmed and the Voice Descriptor

for the selected zone number will be announced, if it is programmed. Press

[✻] to advance.

Zone number

01-41, 95, 96, 99 = Zone number

[✻] = continue

00 = exit Zone Programming mode

• Zone 01 = hardwire

• Zones 02-25 = RF zones (only)

• Zones 26-41 = Button zones (only)

• Zone 92 = Duress

• Zones 95, 96, 99 = Panic zones

Pressing 00 exits mode, upon which the prompt “56” blinks, indicating the

mode is inactive. Press [✻] + any field number to go to that field.

Each zone must be assigned to a zone type, which defines the way in

which the system responds to faults in that zone. Enter the 2-digit zone

type for this zone as follows:

Zone type

00-24 = zone type

b zt

[✻] = continue

[#] = return to previous prompt

00 = Not Used

08 = 24 Hr Aux

01 = Entry/Exit #1

02 = Entry/Exit #2

03 = Perimeter

09 = Fire without verify

10 = Interior w/Delay

20 = Arm–Stay

Note: If 00 is accepted as a zone type, save the 00

zone type and advance to the confirm delete

prompt (F).

04 = Interior Follower

05 = Trouble Day/Alarm Night

06 = 24 Hr Silent

21 = Arm–Away

22 = Disarm

23 = No Alarm Response

24 = Silent Burglary

07 = 24 Hr Audible

The report code consists of 2 hexadecimal digits, each in turn consisting of

2 numerical digits. For example, for a report code of "3C", enter [0][3] for

"3" and [1][2] for "C".

If this is Zone 1, 95, 96 or 99, the system skips to the VOICE

DESCRIPTOR prompt (1C).

Report code

Enter the report code for this zone.

[✻] = continue

C rc

[#] = return to previous prompt

Enter the input type for the transmitter assigned to this zone. Refer to the

transmitter’s instructions for input types of each transmitter.

Input type

3 =RF (supervised RF) – sends periodic

check-in signals, faults, restore and low

Note: Zones 2-25 should be assigned Input Type 3 or 4 . Zones 26-41

battery signals

should be assigned Input Type 5 only.

Note: RF type transmitters must remain within

range of the receiver, otherwise a

supervision failure signal will occur.

4 = UR (unsupervised RF) – sends same as

“RF” type, but control does not supervise

the check-in signals

5 = BR (button type) – sends only fault and low

battery signals; does not send restores or

check-in signals

Note UR and BR type transmitters may be carried

off premises (out of range without causing a

supervision failure.

[✻] = continue

[#] = return to previous prompt

This prompt can be used to enroll loop number and serial number via RF

transmission or the loop number can be enrolled manually. If using the

RF Learning Mode, there is no need to manually enter a loop number.

Proceed directly to RF Learning

Loop number or Loop and Serial

number (if using RF Learning)

1-4 = loop number for the zone of the

transmitter being entered.

0 + [✻] = continue to DELETE ZONE

PARAMETERS CONFIRMATION

prompt (F)

[✻] = continue to the ENROLL MODE prompt

(1A) if not entered, or VOICE

DESCRIPTOR prompt if already entered

[#] = return to previous prompt

Notes: (1) BR type devices cannot be enrolled by using UR or RF type.

Likewise, UR or RF type devices cannot be enrolled by using a

BR type device. There is a 52-second time-out for RF

enrolling. At the end of the time-out, the system returns to

the INPUT TYPE prompt (d). If enrolled, loop number and “L”

are displayed.

(2) Once encrypted (high-security) devices have been enrolled they

must be activated. Refer to the device’s Installation

Instructions to activate the High-Security Mode.

–28–

Download from Www.Somanuals.com. All Manuals Search And Download.

✻

56 Enhanced Zone Programming Mode

RF Learning - Two (2) transmissions (2 key depressions) at least 5

seconds apart will be required for BR type devices (device type 5). Two

beeps will sound after the second transmission, confirming that the loop

number and serial number have been learned.

For all other device types, four (4) transmissions are required (fault,

restore and fault, restore). A single beep will sound after the second

transmission confirming that the loop and serial number have been

captured. Following the fourth transmission the system will confirm that

the loop number and serial number have been learned and announce the

Voice Descriptor for the zone, if it is programmed, followed by two beeps.

Press [✻] to continue.

Manual Entry - Enter the desired loop number and press [✻] to

continue (see the transmitter’s Installation Instructions for specific loop

designations).

Note: The loop number can be changed even if the zone has already

been entered. Care should be taken when using this feature as it

has the capability to make zones inoperable by creating a

mismatch of a working serial number/loop number combination.

This should be re-confirmed if the loop number is changed.

“L” indicates that the zone’s serial number has already been enrolled.

This function deletes either the serial number or all zone information

that is programmed for the zone.

If “00” was entered in the zone type, the confirmation of the delete

request will delete all information associated with the zone currently

being programmed.

Delete zone parameters

confirmation

0 = discard the delete request

1 = confirm requested delete

Note: If 00 was entered as a zone type in prompt

(b), 00 will be retained and system will

advance to prompt (1C)

If “0” was entered in the loop number, the confirmation of the delete

request will delete the serial number of to the zone currently being

programmed.

If “L” is displayed, the serial number for this transmitter has already

been entered. It may, however, still be viewed, confirmed (only if in

listen mode), or deleted.

Enroll mode

0 = advance to the VOICE DESCRIPTOR

prompt (1C).

IA LC

Note: This will save all zone parameters.

View serial number

Enter “3”. Each digit will be redisplayed, and the keypad will beep once

for digits 1-6, and three times for the last digit.

1 = enter now and proceed to SERIAL

NUMBER prompt (1b).

Note: Not applicable if the serial number is

already present.

Confirm serial number

The serial number/loop number combination can be confirmed after one

transmission from a BR type device or two transmissions (fault and

restore) from a UR or RF type device. If a transmission is received that

matches the serial number and loop number entered, the system will

confirm the reception by announcing the Voice Descriptor for the zone, if

it is programmed, followed by three beeps, and a “C” will appear on the

display indicating the received serial number and loop number have

been confirmed. No further transmissions will be received.

2 = copy the last serial number entered into

local ram.

Note: If this is the 1st zone, none will be in the

buffer and the panel will emit a long tone.

Not valid if serial number is already present.

3 = view existing serial number.

Note: Only if “L” is displayed. If “L” is not

displayed, panel will emit a long beep.

Delete serial number

The serial number can be deleted by entering “9”.

9 = advance to F; delete existing serial

number.

Note: Only if “L” is displayed. If “L” is not

displayed, panel will emit a long beep.

If “L” is not displayed, the serial number for this transmitter has not

been previously entered. You may enter the serial number manually,

copy the previous serial number, return to Prompt (E) or enter the serial

number later using the ✻83 Enhanced Sequential Mode.

[✻] = advance to the VOICE DESCRIPTOR

prompt (1C). This will save all zone

parameters.

[#] = return to the LOOP NUMBER prompt

(E).

Note: In order for all entered parameters to be

accepted, you must advance to the VOICE

DESCRIPTOR prompt (1C).

–29–

Download from Www.Somanuals.com. All Manuals Search And Download.

✻

56 Enhanced Zone Programming Mode

Manual entry

Enter "1" to advance to Serial number prompt (1b).

Copy the previous serial number

Enter “2” to copy the previous serial number entered.

Return to Prompt (E)

Enter “#” to return to Loop Number prompt (E).

Enter transmitter later

Enter “0” or “✻” if you wish to enter the transmitter later, using the ✻83

Enhanced Sequential Mode described later in this manual.

Notes: (1) The panel will listen only when it is in the idle loop waiting for

key entry and a serial number has been entered. If a key is

entered, the function must be completed and the panel will

listen again.

(2)

long beep indicates illegal entry or duplicate serial

number/loop entry

In this mode, the transmitter serial numbers can only be entered

manually.

Serial number

Enter the transmitter’s 7-digit serial number.

[#] = return to prompt 1A and reject any serial

numbers entries that have been made.

[✻] = return to prompt 1A, (if a valid serial

number has been entered, the "L" is

displayed and the serial number will be

copied into EEROM from the last serial

entered into the buffer.)

Enter the 7-digit serial number printed on the transmitter. If an incorrect

digit is entered, press the [#] key to backup to prompt (1A) and start over.

When all 7 digits are entered, press the [✻] key.

If 52 seconds passes and no entry has been made, the system returns to

prompt (1A).

Notes: (1) If the serial and loop number combination is already present

the keypad will emit a single long beep and the system will

return to the (1A) prompt and “L” will be displayed.

(2) If less than 7 digits have been entered, the keypad will emit a

single long beep and return to the (1A) prompt without

displaying the “L”.

Note: This prompt can be used only to manually

enroll a serial number. RF enrollment will be

rejected and the current zone descriptor will

be announced, followed by a single long

beep and the system will return to prompt

(1A).

(3) If more than 7 digits have been entered, the first 6 digits will

be saved along with the last digit that was entered (entering

123456789 yields the serial number 1234569).

Each zone can have a voice descriptor of up to 3 words that will be

announced whenever the system announces status for that zone.

Voice descriptor

0 = skip to next zone (A)

1 = enter descriptor mode; existing descriptor

for this zone will be announced

† see ✻84 Assign Zone Voice Descriptors section for vocabulary index

Descriptor 1

Enter [#] + 2-digit vocabulary index number†

of first descriptor word for this zone.

6 = accept word and advance to descriptor 2

(descriptor 2 will be announced)

8 = accept word and advance to next zone

(prompt A) – entire zone descriptor will be

announced

Use the [6] or [8] key to advance as described.

To change the entered index number before pressing [6] or [8], simply press

[#] + desired 2-digit vocabulary index number.

If descriptor 1 is not desired, enter [#] + 99 (blank), then press [8] to return

to zone number prompt.

Id vi

Press any other key to repeat the selected word.

† see ✻84 Assign Zone Voice Descriptors section for vocabulary index

Descriptor 2

Enter [#] + 2-digit vocabulary index number†

of second descriptor word for this zone.

6 = accept word and advance to descriptor 3

(descriptor 3 will be announced)

8 = accept word and advance to next zone

(prompt A) – entire zone descriptor will be

announced

IE vi

Use the [6] or [8] key to advance as described.

To change the entered index number before pressing [6] or [8], simply press

[#] + desired 2-digit vocabulary index number.

If descriptor 2 is not desired, enter [#] + 99 (blank), then press [8] to return

to zone number prompt.

Press any other key to repeat the selected word.

† see ✻84 Assign Zone Voice Descriptors section for vocabulary index

Descriptor 3

Enter [#] + 2-digit vocabulary index number†

of third descriptor word for this zone.

6 or 8 = accept word and advance to next

zone (prompt A) – entire zone

Use the [6] or [8] key to advance as described.

To change the entered index number before pressing [6] or [8], simply press

[#] + desired 2-digit vocabulary index number.

If descriptor 3 is not desired, enter [#] + 99 (blank), then press [8] to return

to zone number prompt.

IF vi

descriptor will be announced

Press any other key to repeat the selected word.

–30–

Download from Www.Somanuals.com. All Manuals Search And Download.

✻

80 Device Programming Menu Mode

Powerline Carrier devices (eg., X-10 brand devices) are programmable switches that can be used to perform

many different functions. They can be used to turn lights on and off, control sounders, or for status

indications. In this system, each device must be programmed as to how to act (ACTION), when to activate

(START), and when to deactivate (STOP). Each of these is described below.

The control supports a total of 8 output devices.

The 1332X10 transformer sends signals from the control panel through the premises AC wiring to the

Powerline Carrier Devices (which are plugged into AC outlets). Devices plugged into Powerline Carrier

Devices can then be made to perform various functions in response to commands entered at the keypads in

the security system.

Powerline Carrier Devices are not UL Listed for fire or burglary functions and are intended for home automation.

Programming Options Defined

The following will help you understand the programming of output devices when using ✻80 and ✻81 modes.

ACTION The "ACTION" of the device is how the device will respond when it is activated by the

"START" programming. There are four different choices of actions:

• ACTIVATE for 2 SECONDS and then reset.

• ACTIVATE and REMAIN ACTIVATED until stopped by some other event.

• PULSE ON and OFF until stopped by some other event.

• NOT USED when the device is not used.

START

The "START" programming determines when and under what conditions the device will

be activated. The following START options are available:

Start by Event

1. Event is the condition (alarm, fault, trouble) that must occur to a zone or group of

zones (zone list) in order to activate the device. These conditions apply only when a

zone list is used. The different choices for "EVENT" are listed below and in the

“Programming Powerline Carrier Devices” paragraph that follows.

• ALARM

• FAULT

Device activates upon any alarm in an assigned zone in the zone list.

Device activates upon any opening or short in an assigned zone in the zone list.

• TROUBLE Device activates upon any trouble condition in an assigned zone in the zone list.

• NOT USED Device action is not dependent upon one of the above events.

2. A zone list is a group of zones to which the “EVENT” applies in order to activate a

particular device. Note that there are a total of 3 output device-related zone lists

that can be programmed in ✻81 menu mode; when the selected EVENT (alarm, fault

or trouble) occurs in any zone in the selected “Start” ZONE LIST (1, 2, or 3),

activation of the selected device will START.

Start by Zone Type or System Operation

•

If a system operation, such as “DISARMING” or “ANY FIRE ALARM,” is to activate

the device, the appropriate choice would also be entered under the “ZONE TYPE”

option. “ZONE TYPE” is used independently of the “EVENT/ZONE LIST”

combination.

If a "ZONE TYPE" is chosen, any zone of that response type going into alarm,

trouble, or fault will cause the device to activate as selected in "ACTION.” If the same

“ZONE TYPE” is also chosen for the STOP programming, any zone of that type that

restores will de-activate the device.

If a "SYSTEM OPERATION" is chosen (e.g., End of Exit Time), that operation will

cause the device to activate as selected in "ACTION.” The different choices for

"ZONE TYPE" and "SYSTEM OPERATION" are listed in the “Start zone type”

paragraphs later in this section, and in the Programming Form.

–31–

Download from Www.Somanuals.com. All Manuals Search And Download.

✻

80 Device Programming Menu Mode

The "STOP" programming determines when and under what conditions the device will be de-

activated. The following options are available:

STOP

Upon Restore of a Zone List

Restore Zone List: If a "ZONE LIST" is used as the “Stop” event, the device will de-activate when all the

zones in that list restore from a previous fault, trouble, or alarm condition. This will occur regardless of

what is programmed to "START" the device; therefore, a "RESTORE ZONE LIST" would normally only be

used when a "ZONE LIST" is used to start the device.

Upon a Zone Type or System Operation

Zone Type/System Operation: Instead of using a "RESTORE ZONE LIST," a specific zone (response) type or

system operation action can be selected to de-activate the device.

•

If a specific "ZONE TYPE" is chosen, any zone of that response type that restores from a previous alarm,

trouble, or fault condition will cause the device to de-activate.

•

If a "SYSTEM OPERATION" is chosen, that operation will cause the device to de-activate.

During normal system operation, any devices may be manually started by keypad entry of: Code* + [#]

+ 4 + “n;” or manually stopped by keypad entry of: Code* + [#] + 7 + “n,” where “n” = the device number to

be controlled.

* Code is required for devices 7 and 8. For devices 1-6, code is not required. See User Manual for more

information.

Programming Powerline Carrier Devices

While in program mode, press ✻80 to enter Output Device Menu Mode. This mode is used to program

all output devices used in the system. Refer to the output device table for ✻80 on the separate programming

form when programming output devices.

Note: The House ID of the Powerline Carrier Devices must be entered in data field ✻25.

The prompts for ✻80 are as follows:

Powerline Carrier Device Programming Main Menu prompt

A 01

Device Number--------------------- for entering the device number

Device Action ----------------------- for defining the action the device will perform when active

Start Event Type ------------------ for assigning the event type to start the action

Start Zone List--------------------- for assigning the zone list to start the action

Start Zone Type-------------------- for assigning the zone type to start the action

Stop Zone List---------------------- for assigning the zone list to stop the action

Stop Zone Type--------------------- for assigning the zone type to stop the action

–32–

Download from Www.Somanuals.com. All Manuals Search And Download.

✻

80 Device Programming Menu Mode

The following explains these prompts in detail. The left two columns identify the prompts and list the

available entries. The right-most column provides a further explanation of the entries.

Note: Entering a number other than one specified will give unpredictable results.

Entering “1” advances to the next prompt below.

Entering “0” exits mode, upon which this prompt blinks, indicating the

mode is inactive.

Powerline Carrier Device

programming

0 = exit mode

1 = enter mode

Enter device numbers as 2-digit entries.

Device number

01-08 = device number to be programmed

[✻] = continue

00 = exit Device Programming mode

Enter the 1-digit action (0-3) for the device being programmed (current

action is displayed).

NOTES:

1. If “3” is entered (pulse), only up to 3 different devices can be pulsed

if one of the devices is a siren/horn (X-10 Powerhouse Security

model SH10A). In addition, the siren/horn cannot be manually

activated using the lights on/lights off keypad commands.

2. If using an X-10 Powerhouse Security SH10A siren:

• you must use device action “3.”

Device action

0 = No response

b aa

1 = Close for 2 seconds

2 = Close and Stay Closed

3 = Continuous Pulse on & off (1 sec ON, 1 sec

OFF)

[✻] = continue

[#] = return to previous prompt

• you must change the device action default to “3” if using default

table 2 or 4

Enter the 1-digit event type (0-3) to activate the device being

programmed. A zone list must be used in conjunction with an event. If

a zone type/system operation is to be used instead of an event, enter

“0”.

Start event type

0 = Not used

1 = Alarm

2 = Fault

3 = Trouble

[✻] = continue

[#] = return to previous

prompt

If a zone list will be used to start the device action, enter the zone list

number at this prompt.

Start zone list

1-3 = zone list number (to be programmed in

field ✻81)

0 = zone list not used for this device

[✻] = continue

[#] = return to previous prompt

Start zone type

If a zone type or system operation will be used to start the device

action, enter the appropriate 2-digit code for the device being

programmed (see table that follows).

01-58 = zone type to start this device action

(select only those that are applicable)

00 = zone type not used for this device

[✻] = continue

Choices for zone types

00 = Not Used

04 = Interior Follower

05 = Trouble Day/Alarm Night 09 = Fire

06 = 24 Hr Silent

07 = 24 Hr Audible

08 = 24 Hr Aux

01 = Entry/Exit #1

02 = Entry/Exit #2

03 = Perimeter

[#] = return to previous prompt

10 = Interior w/Delay

24 = Silent Burglary

Choices for system operation

20 = Arming–Stay

21 = Arming–Away

22 = Disarm. (Code + OFF) 38 = Chime

31 = End of Exit Time 39 = Any Fire Alarm

33 = Any Alarm (except zt 08) 42 = Sys. Batt. Low

36 = At Bell Timeout**

43 = Comm. Failure

52 = Kissoff

58 = Duress

32 = Start of Entry Time

40 = Bypassing

** Or at Disarming (which ever occurs earlier)

Note: If an X-10 device has been programmed to ZT05 or ZT07 and *55

has been enabled, the device response will be dependent upon the

selection made in *55 Field "Ln".

If a zone list will be used to STOP, or restore, the device action, enter

the zone list number 1, 2, or 3 (to be programmed in ✻81 mode). If not

used, enter “0”.

Stop zone list

1-3 = zone list to stop this device action

0 = zone list not used

[✻] = continue

[#] = return to previous prompt

If a zone type or system operation will be used to STOP the device

action, enter the appropriate 2-digit code (see the "ZT" choices listed

above). If not, enter 00.

The display then returns to the DEVICE NUMBER prompt (A) so that

you can enter the next device number to be programmed, or enter [0][0]

to end device programming.

Stop zone type

01-58 = zone type to start this device action

(select only those that are applicable)

00 = zone type not used for this device

[✻] = continue

IA zt

[#] = return to previous prompt

–33–

Download from Www.Somanuals.com. All Manuals Search And Download.

✻

81 Zone List Menu Mode

While in Program mode, press

✻81 to enter Zone List Menu Mode. This mode is used to program zone

lists for output devices (programmed in ✻80 menu mode) or Chime-by-Zone in Zone List 3.

NOTES:

• Any list may include any or all of the systems zone numbers.

• A zone list can be assigned to more than one Powerline Carrier Device.

The prompts for *81 are as follows:

Zone List Programming ------------------- Main Menu prompt

A 01

Zone List Number --------------------------- for entering the zone list number to be programmed

Zone Entry to List--------------------------- for entering zones to the assigned zone list

Delete Entire List? -------------------------- for deleting the entire zone list and its contents

Delete Specific Zones From List? ------- Selects whether to delete zones or return to next zone list number

Delete Zones----------------------------------- for deleting specific zones from the current zone list

The following explains these prompts in detail. The left two columns identify the prompts and list the

available entries. The right-most column provides a further explanation of the entries.

Notes: (1) Entering a number other than one specified will give unpredictable results.

(2) Do not assign zones with zone types 20, 21 or 22 to a zone list.

Pressing 1 advances to the next prompt below.

Pressing 0 exits mode, upon which this prompt blinks, indicating

the mode is inactive.

Zone list programming

0 = exit mode

1 = enter mode

Enter the Zone List Number 01, 02, or 03 to program (or 00 if no

zone lists are used).

Zone list number

01-03 = zone list number to be programmed

00 = exit Zone List mode

[✻] = continue

Enter each zone number to add to the zone list by first entering

the zone number, then the [✻] key (for example, 01✻ 02✻ 03✻).

The system will announce the Voice Descriptor for the selected

zone, if it is programmed. After all desired zones are enrolled,

enter “00” to advance.

Zone entry to list

01-41, 95, 96, 99 = zone numbers to add to

zone list

[✻] = accept zone number and enter the next

zone number

00 = accept zone number(s) and continue to

next prompt

To delete the zone list, enter “1”. All zones in the zone list will be

deleted automatically and programming will return to the ZONE

LIST NUMBER prompt.

Delete entire zone list?

0 = don’t delete; continue to next prompt

1 = delete the current zone list

To save the zone list or delete specific zones from the list, enter

“0”.

To save the entire zone list, enter “0” and programming will

return to the ZONE LIST NUMBER prompt.

To delete a zone or zones in a zone list enter “1”.

Delete zones from list?

1 = continue to delete zones prompt

0 = don’t delete; continue to next zone list

number prompt (A….01)

[#] = return to zone list number prompt

(A….01)

When deleting a zone(s) from the zone list, if the selected zone

has a Voice Descriptor programmed, upon deletion it will be

announced as a confirmation that it has been deleted. After all

zones to be deleted are entered, enter “00” to return to the ZONE

LIST NUMBER prompt so that another list can be programmed,

if desired.

Delete zones

Enter each 2-digit zone number to be deleted

from the current zone list, followed by the [✻]

key.

[✻] = delete zone and enter next zone to be

deleted

00 = delete zone and return to next zone list

number prompt (A….01) desired

–34–

Download from Www.Somanuals.com. All Manuals Search And Download.

✻

83 Enhanced Sequential Mode

By using this mode, you can add, delete, or change the serial number of a transmitter in a zone, but retain

all other existing data that has been programmed for that zone. Note that the ✻83 Enhanced Sequential

mode requires that all zone information must first be entered using the ✻56 Enhanced Zone Programming

mode for all zones below zone number 26 (4 button key area).

Note: Any zone which already has a serial number learned in will not be accessible in ✻83 Enhanced

Sequential mode!

Certain button-type transmitters have more than one button (e.g., 5804). Note that each button must be

assigned to a different zone. Similarly, the 5816 Transmitter has contact terminals and a reed switch for use

with a magnet. If using both, each must also be assigned to a different zone.

This means that the procedures that follow must be repeated for each button-type zone below zone number

26 or contact on the transmitter. Four zone button-type devices are held in zones 26 and above. They will be

started on boundaries of zones 26, 30, 34, and 38. These four zone button-type devices will have the option to

have all information entered in this field. One entry will set the loop number, report code, zone type, and

input device type for all 4 buttons, and a second entry will enter one serial number into four zones.

Note: Use this mode only after all other zone information has been programmed, including transmitter loop

numbers except for button-type zones over zone number 26. The panel will stop at zones 26, 30, 34

and 38 and zone data can be entered as a default here.

Enter Serial Number Sequential mode by pressing ✻83. The prompts for ✻83 are as follows:

A 01

Zone Number ------------------------------------ for entering the zone number to be programmed

Enroll Mode-------------------------------------- Selects method of serial number or viewing

Enroll Serial Number------------------------- for entering transmitter serial numbers

Delete Serial Number------------------------- for deleting existing serial numbers

The following explains these prompts in detail. The left two columns identify the prompts and list the

available entries. The right-most column provides a further explanation of the entries.

Notes: (1) Entry of a number other than one specified will give unpredictable results.

(2) In Enhanced Sequential Mode, 4 button type keys will always be enrolled simultaneously. They will be stopped at the 4 button

boundaries of 26, 30, 34 and 38, provided the zone is free of a serial number. If the first zone of the key has a serial number

enrolled, the remaining keys cannot be programmed in sequential mode. In addition, if the zone has not been set up (duplicate

loop, missing zone type, etc.) only entries 0 (skip to the next zone) and 4 (copy the key template) will be allowed.

(3) You may find it convenient to adjust the volume setting before entering the Programming Mode. This will allow you to clearly

hear feedback announcements or system beeps.

Enter the 2-digit zone number of the first transmitter to have its serial

number entered. The system will announce the Voice Descriptor for the

selected zone number, if it is programmed.

Zone number

Enter the 2-digit zone number.

[✻] = continue; system searches for zones not

yet entered (for zones 2 through 25 a zone

type must be entered), then advances to

ENROLL SERIAL NUMBER prompt “1b”

00 = exit Sequential mode

Press [✻] to continue. Starting with this zone number, the system will

search for the first transmitter that has all of the following attributes

pre-programmed in ✻56 ENHANCED ZONE PROGRAMMING:

Make sure that the appropriate input type was selected in ✻56 (RF,

UR, or BR programmed)

Make sure that the appropriate loop number was selected in ✻56.

No serial number programmed

Zone type

If the first zone number entered does not have one or more of the above

attributes, the system will search its database for the first zone that

does, and will display it at the enroll SERIAL NUMBER prompt (1b).

Pressing 00 exits mode, upon which the prompt “83” blinks, indicating

the mode is inactive.

Note: Two exceptions to the requirement above exist for keys. Four zone

button type devices (zone numbers 26, 30, 34, and 38) will be

stopped only if there are no serial numbers enrolled in all 4 zones

of the key, regardless of the attributes that have been entered. In

addition, zone types are not required to be present. In this case,

1A, Option 4 must be selected prior to “Learn”.

–35–

Download from Www.Somanuals.com. All Manuals Search And Download.

✻

83 Enhanced Sequential Mode

Note:If “L” is displayed, the serial number for this transmitter has

Enroll mode

already been entered, however, it may still be confirmed,

viewed or deleted.

0 = advance to next zone to be enrolled

1 = enter now and proceed to SERIAL NUMBER

prompt (1b).

For 4 button keys (zones 26-29, 30-33, 34-37, &

38-41) the serial number will be enrolled to all four

buttons.

If the transmitter’s serial number has not been previously entered, you

may enter the enroll serial number mode (1A) by entering “1”, or copy

the last serial number that was entered by entering “2”.

IA LC

If the transmitter’s serial number has been previously entered, you may,

view the present serial number by entering “3”. If view is selected each

digit will be re-displayed, and the keypad will beep once for digits 1-6,

and three times for the last digit. Once the serial number has been

entered by either selecting a “1” or a “2”, you will return to this prompt

with the “L” on the display. The serial number/loop number combination

that was entered can be confirmed by getting two transmissions (fault

and restore) from the RF or UR device or one transmission from the BR

device. If a transmission is received that matches the serial number and

loop number entered, the system will announce the Voice Descriptor for

the loop followed by three beeps, and a “C” will be displayed indicating

that the received serial number and loop number transmission has

been confirmed to match. No further transmissions will be received.

When confirming a 4 button key, only the serial number is confirmed,

since it assumed that all loops are used. Pressing any key will allow a

confirmation.

If enrolling a key, the panel will emit a long beep

when entering a 1 to indicate that the present key

set up is invalid.

Notes: 1. A valid template or key has 4 existing

zones, each with a zone type, unique loop

number.

2. If the display automatically advances to

"1A" rather than "1b" the configuration of

the key is not valid. At that point copy

template, skip, or return are the only legal

entries.

2 = copy the previous serial number entry from

the buffer.

Notes: 1. Before you can copy a serial number you

must first enter a serial number. If no

serial is stored in the buffer and a copy is

attempted the panel will emit a long beep

indicating an invalid operation.

*Long beep indicates illegal entries, or duplicate serial number/loop

entry*

2. Not applicable for 4 button key zones 26-

29, 30-33, 34-37, & 38-41.

When the last zone has been entered, the display will remain on that

zone. To exit this mode and return to data field program mode, press 00

at the ZONE NUMBER prompt.

3 = view existing serial number.

Note:

Only if “L” is displayed. If the “L” is not

displayed the panel will emit a long beep.

When all zones have been programmed, test each zone using the

system’s Test mode. Do not use the Transmitter ID Sniffer mode for this,

since it will only check for transmission of one zone on a particular

transmitter, and not the zones assigned to each additional loop.

4 = copy the 4 button key template that has been

set in zone numbers 26-29 (all zone para-

meters except serial numbers). (Only valid on

zones 30-33, 34-37, & 38-41 that do not have

serial numbers enrolled.)

Notes: 1. Template acceptance is indicated by two

beeps after copying.

For Zones 26-29, 30-33, 34-37, and 38-41 any loop can be used for RF

enrollment. If enrolling via RF, it will be confirmed without additional

transmissions.

2. A single long beep emitted when copying

a indicates the template is not valid.

9 = delete existing serial. Go to the (1A) prompt.

For 4-button key, zones 26-29, 30-33, 34-37,

& 38-41 have serial numbers. Delete all four

at one time.

Note: Only if “L” is displayed. If the “L” is not

displayed the panel will emit a long beep.

[✻] = advance to next zone to be enrolled

[#] = return to previous prompt (A)

–36–

Download from Www.Somanuals.com. All Manuals Search And Download.

✻

83 Enhanced Sequential Mode

This prompt can be used to enroll the transmitter serial number via

Serial number

RF transmission or manually. If using the RF Learning Mode there

is no need to manually enter a serial number. Proceed directly to RF

Learning. Upon entering the Serial Number mode, the Zone

Descriptors will be announced.

Enter transmitter’s 7- digit serial number via RF

learning or manually.

Ib zz

[#] = return to (1A) prompt and reject whatever

serial number entries have been made.

[✻] = return to (1A) prompt (if a valid serial

number has been enrolled, “L” is displayed

and the serial number will be copied into

EEROM and the last serial entered buffer.

Note: BR type devices can be enrolled only by transmission from BR

devices. Likewise, UR and RF devices can only be enrolled by

transmission from a UR or RF device

RF Learning - Two (2) transmissions (2 key depressions) at least

five seconds apart, will be required for BR type or four (4)

transmissions (fault, restore and fault, restore) for UR or RF type. If

the learned serial number has a different loop number than that

entered in ✻56 the system will announce the Voice Descriptor, if it

is programmed, followed by two beeps and will return to Prompt (1A)

and “L” will be displayed.

Note: For zones 26, 30, 34 and 38 only BR type

devices can be used.

If the loop number captured by RF transmission and that entered in

✻56 mode match, the system will announce the Voice Descriptor, if it

is programmed, followed by three beeps and return to Prompt (1A)

and “LC” will be displayed. No additional transmissions are needed

for confirmation.

Manual Entry - Enter the 7-digit serial number printed on the

transmitter. If you enter an incorrect digit, press the [#] key to

backup to prompt (1A) and start over. When all 7 digits are entered,

press the [✻] key. If less than 7 digits are entered, the keypad will

emit a single long beep and return to the (1A) prompt without

displaying the “L”.

If more than 7 digits have been entered, the first 6 digits will be

saved along with the last digit that was entered (entering 123456789

yields the serial number 1234569).

Note: If 52 seconds pass and no entry has been made, the system

returns to prompt (1A).

This function deletes only the serial number.

Delete serial number

0 = discard the delete request

1 = confirm requested delete

Entering a “9” at prompt (1A). Confirmation of the delete request will

cause deletion of the serial number pertaining to the zone being

programmed.

Note: Entering a “9” at prompt (1A) will cause the

panel to return to prompt (1A) regardless of

the confirmation answer.

Note: In Enhanced Sequential Learn Mode, 4 button type keys will always be learned simultaneously. They will be stopped at the 4

button boundaries of 26, 30, 34 and 38, provided the zone is free of a serial number. If the first zone of the key has a serial

number learned, the remaining keys cannot be programmed in sequential learn mode. In addition, if the zone has not been set

up (duplicate loop, missing zone type, etc.) only entries 0 (skip to the next zone) and 4 (copy the key template) will be allowed.

–37–

Download from Www.Somanuals.com. All Manuals Search And Download.

✻

84 Assign Zone Voice Descriptors

Use this mode to assign voice descriptors for each zone. These are the descriptors that are announced when

the system announces any event involving a zone number. Each descriptor can consist of up to 3 words.

Press ✻84 while in Programming mode.

The prompts for ✻84 are as follows:

Voice Descriptors---------------------- Main Menu prompt

A 01

Zone Number --------------------------- for entering the zone number to be programmed

Descriptor 1----------------------------- for assigning the first word of this zone’s descriptor

Descriptor 2----------------------------- for assigning the second word of this zone’s descriptor

Descriptor 3----------------------------- for assigning the third word of this zone’s descriptor

The following explains these prompts in detail. The left two columns identify the prompts and list the

available entries. The right-most column provides a further explanation of the entries.

Note: Entering a number other than the one specified will give unpredictable results.

Pressing 1 advances to the next prompt below.

Pressing 0 exits mode, upon which this prompt blinks, indicating the

mode is inactive.

Assign zone voice descriptors

0 = exit mode

1 = enter mode

Enter the 2-digit zone number for which this descriptor is being

assigned, then press [✻]. The Voice Descriptor for the selected zone will

be announced, if it is programmed.

Zone number

[✻] = continue to next prompt (any existing

descriptors will be announced, then

descriptor 1 will be repeated)

00 = exit voice descriptor mode

Enter the first word of the descriptor for the selected zone.

Use the [6] or [8] key to advance as described.

To change the entered index number before pressing [6] or [8], simply

press [#] + desired 2-digit vocabulary index number.

If descriptor 1 is not desired, enter [#] + 99 (blank), then press [8] to

return to zone number prompt.

Descriptor 1

Enter [#] + 2-digit vocabulary index number of

first descriptor word for this zone.

6 = accept word and advance to descriptor 2

(descriptor 2 will be announced)

8 = accept word and advance to prompt (A) for

next zone. Press any other key to repeat the

selected word.

b vv

Enter the second word of the descriptor for the selected zone.

Use the [6] or [8] key to advance as described.

To change the entered index number before pressing [6] or [8], simply

press [#] + desired 2-digit vocabulary index number.

If descriptor 2 is not desired, enter [#] + 99 (blank), then press [8] to

return to zone number prompt.

Descriptor 2

Enter [#] + 2-digit vocabulary index number of

second descriptor word for this zone.

6 = accept word and advance to descriptor 3

(descriptor 3 will be announced)

8 = accept word and advance to prompt (A) for

next zone. Press any other key to repeat the

selected word.

Enter the last word of the descriptor for the selected zone.

Use the [6] or [8] key to advance as described.

To change the entered index number before pressing [6] or [8], simply

press [#] + desired 2-digit vocabulary index number.

If descriptor 3 is not desired, enter [#] + 99 (blank), then press [8] to

return to zone number prompt.

Descriptor 3

Enter [#] + 2-digit vocabulary index number of

third descriptor word for this zone.

6 or 8 = accept word and advance to prompt

(A) for next zone. Zone descriptor will

be announced. Press any other key to

repeat the selected word.

d vv

–38–

Download from Www.Somanuals.com. All Manuals Search And Download.

✻

84 Assign Zone Voice Descriptor

VOICE VOCABULARY INDEX

00 ½ second pause

SYSTEM WORDS

AC LOSS

ARMED

AWAY

BYPASSED

CHIME

DISARMED

DISARM SYSTEM

NOW

EXIT NOW

FAULT

INSTANT

LOW BATTERY

NOT

READY TO ARM

STAY

48 GARAGE

49 GUEST ROOM

09 GUN

61 PATIO

62 POLICE

18 POOL

81 ZERO

86 ZONES

82 ALARM

32 ATTIC

29 1^ST

30 2^ND

31 3^RD

63 REAR

19 ROOM

50 HALL

01 BABY

33 BACK

34 BASEMENT

35 BATHROOM

36 BEDROOM

70 Custom Word #1

71 Custom Word #2

72 Custom Word #3

73 Custom Word #4

74 Custom Word #5

10 INSIDE

64 SECOND FLOOR

65 SEVEN

20 SHED

21 SHOP

66 SIDE

51 KITCHEN

99 Blank (for erasing

a previously

83 CHECK

67 SILENT POLICE

68 SIX

69 SLIDING

22 SMOKE

23 SOUTH

24 STORAGE

85 SYSTEM

11 LAUNDRY

52 LAUNDRY

ROOM

12 LIBRARY

13 LIVING

53 LIVING ROOM

programmed

word)

37 DELAY DOOR

38 DEN

02 DETECTOR

03 DINING

39 DINING ROOM

04 DOOR

40 DOWNSTAIRS

05 DRIVEWAY

14 MAIN

25 THIRD FLOOR

75 THREE

76 TRANSMITTER

77 TWO

15 MASTER

54 MASTER

BEDROOM

55 MEDICAL

84 MESSAGE

56 MOTION

DETECTOR

06 EAST

41 EIGHT

42 EMERGENCY

78 UPSTAIRS

26 UTILITY

79 UTILITY ROOM

43 FAMILY ROOM

87 FIRE

44 FIRE DETECTION

07 FIRST FLOOR

45 FIVE

08 FLOOR

46 FOUR

57 NINE

16 NORTH

58 NURSERY

27 WEST

80 WINDOW

59 OFFICE

60 ONE

17 OUTSIDE

28 YARD

47 FRONT

Note: If button type device is used to Arm Away, Arm Stay, and disarm the system it is recommended to assign “Check” and

“Zones” voice descriptors to each of the three zones. This will allow the system to announce “Check Zones” “Low

Battery” if the button device has a low battery.

–39–

Download from Www.Somanuals.com. All Manuals Search And Download.

✻

85 Record Custom Voice Descriptors

Use this mode to record up to 5 custom voice descriptors. Press ✻85 while in Programming mode.

Note: Entering a number other than one specified will give unpredictable results.

Entering “1” advances to the next prompt below.

Entering “0” exits mode, upon which this prompt blinks, indicating the

mode is inactive.

Assign custom voice descriptors

0 = exit mode

1 = enter mode

Record up to 5 custom words.

Custom descriptor number

Enter 7 + d + [✻]

Where d = 0-4, each representing custom

word 70, 71, 72, 73, or 74, respectively. Any

existing word will be announced.

Press [#] to start recorder. Begin speaking

immediately after the third beep.

Speak the desired word clearly near the

microphone. Recording stops after 1.5

seconds.

6 = accept word and ready to record next

descriptor prompt (A….7d)

[#] = re-record descriptor

00 = exit Record mode after pressing 6 to

accept word

Press any key to repeat the recorded word.

–40–

Download from Www.Somanuals.com. All Manuals Search And Download.

Voice Prompt Programming

The LYNXR Series features a quick programming mode that allows you to program the system by

responding to a series of voice prompts. The Voice Prompt Programming Guide provides you with the

information required to use this feature.

Voice Prompt Programming Keypad Functions:

The keys shown below are used to navigate through the Voice Prompt Programming Feature.

1. ESCAPE/ OFF key: Used at any

time to exit the current menu and

return to the previous prompt.

2. ADD/ AWAY key: Used to add

sensors, or keys or save data when

ARMED

READY

entering phone or account

numbers.

OFF

ESCAPE

RECORD

VOLUME

PLAY

AWAY

ADD

LIGHTS ON

TEST

BYPASS

3. DELETE/ STAY key: Used to

STAY

LIGHTS OFF

CODE

CHIME

delete a sensor when in the delete

Sensors Menu.

DELETE

AUX

SELECT

STATUS

NO DELAY FUNCTION

4. SELECT/ AUX key: Used to

confirm a selection.

3 ↑ key: Used to scroll forward

01009-021-V0

through menu choices.

6. 6 ↓ key: Used to scroll backward

through menu choices.

7. FUNCTION/ # key: Used to repeat a voice prompt. (This function cannot be used while entering phone or account numbers.)

Notes: (1) Keying in any new command will terminate the active voice prompt.

(2) If an irrelevant command is entered LYNXR will generate a long rejection beep and repeat the previous voice prompt.

(3) Phone numbers and account numbers can be left blank by pressing the “ADD/ AWAY ” key without entering any data.

(4) LYNXR automatically saves phone and account number data once all available digits are entered.

ENTERING VOICE PROMPT PROGRAMMING

Power-up the control and enter the Installer Code

(4 1 1 2) + 8 8 8.

Follow the directions provided by each voice prompt to

make your selections.

Once you have entered into the Voice Prompt Programming

Mode the system will announce, “Programming, use

ARROWS to scroll choices, press SELECT to accept, press

ESCAPE to quit.”

The FUNCTION/ # key can be used to repeat a voice

prompt, as required.

When you have completed each programming procedure

the system will return to the Main Programming Menu.

Press the 6 ↓ or 3 ↑ keys to scroll through the voice

menu and follow the instructions provided.

EXITING VOICE PROMPT PROGRAMMING

The system will announce the following options:

“Add Sensors”

“Delete Sensors”

“First Central Station Phone Number”

“First Central Station Account Number”

“Second Central Station Phone Number”

“Second Central Station Account Number”

“Templates”

Once you have returned to the Main Programming Menu,

the system will announce, “Programming use ARROWS to

scroll choices, press SELECT to accept, press ESCAPE to

quit”.

Press ESCAPE/ OFF to exit Voice Prompt programming

mode once you have returned to the Main Programming

Menu.

“Expert Programming Mode”

–41–

Download from Www.Somanuals.com. All Manuals Search And Download.

Voice Prompt Programming

Enter Voice Prompt Programming Mode: (Installer Code + 8 8 8). Follow the voice prompts to

advance to the selected item in the Main Programming Menu.

Add Sensors

Delete Sensors

First Central Station Phone Number

First Central Station Account Number

Second Central Station Phone Number Second Central Station Account Number

Templates Expert Programming Mode

Program each option as shown below. Use the 6 ↓ and 3 ↑ keys to scroll through the voice menu and follow the voice prompts to

program the LYNXR.

The LYNXR will enroll a sensor once the transmitter has been activated two times. The system will confirm the

enrollment following each subsequent activation of the same transmitter.

To Add a Door Sensor

(1) Delay Door Location

Front

Back

Side

Basement

Sliding

Hall

Garage

Kitchen

Patio

To add a Window, Motion Detector, or Fire Detection Sensor

(2) Sensor Type

(3) Sensor Location

(4) Location Modifiers

Window

Motion Detector

Fire Detection

Living room

Dining room

Bedroom

Bathroom

Nursery

Kitchen

Hall

Den

Upstairs

Downstairs

First

Second

Third

Second Floor

Front

Family Room

Guest Room

Laundry Room

Utility Room

Garage

Attic

Basement

Master Bedroom

Office

Upstairs

Rear

Side

–42–

Download from Www.Somanuals.com. All Manuals Search And Download.

Voice Prompt Programming

To Delete Sensors

To Add an Emergency Pendant

(5) Pendant Type

Medical

Fire

Silent Police

Police

When adding wireless keys, wait 5 seconds between transmissions.

To Add a Wireless Key

LYNXR automatically saves phone and account number data once all available digits are entered.

To Add First Central Station Phone Number

All four digits of the Central Station Account number must be entered. If ten-digit format is selected, all ten digits

must be entered.

To Add First Central Station Account Number

–43–

Download from Www.Somanuals.com. All Manuals Search And Download.

Voice Prompt Programming

All four digits of the Central Station Account number must be entered. If ten-digit format is selected, all ten digits

must be entered.

To Add Second Central Station Phone Number

To Add Second Central Station Account Number

Refer to the LYNXR Series Installation and Setup Guide to view the complete set of Template (default table) selections.

To Program a Template (Default Table)

(6) Template selections

Template 1

Template 2

Template 3

Template 4

To Enter Expert Programming Mode

Once you have entered the Expert Programming Mode, the [ESCAPE] key can be used to return to the Voice Prompt

Programming mode.

–44–

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote Programming/Control

(Downloading)

General Information

The control panel can be remotely programmed from an IBM-compatible Personal Computer (PC), a HAYES

Modem, and ADEMCO’s Compass Downloader for Windows (as specified below).

Downloading may only be performed if a technician is at the site.

Multiple security levels protect remote programming against compromise by attempts to defeat the system.

1. Security Code Handshake: An 8-digit download ID code must be matched between the Control and

downloader.

2. Site-Initiated Remote Programming: The installer or subscriber initiates the call from the subscriber

premises (by entering Installer Code + # + 1) while disarmed. All parameters can then be downloaded via

the phone lines using a personal computer.

3. Station-Initiated Remote Programming: The operator calls the site from your office to initiate the

download call. The Control hangs up and then calls back the PC via the preprogrammed telephone

number. The unit can then be uploaded, downloaded, or controlled from your office.

4. Telco Handoff: The installer or subscriber performs a download session on the call initiated from the

site or from local laptop computer (by entering Installer or Master Code + # + 1 at the control panel).

5. Data Encryption: Data passed between the PC and the Control is encrypted for security so that it is

very difficult for a foreign device tapped into the phone line to take over communication and substitute

system-compromising information.

Equipment required to download to a system at the premises

• An IBM PC compatible computer and appropriate interconnecting cables.

• Either a HAYES brand SMARTMODEM 1200 (Level 1.2 or higher external or Level 1.1 or higher [with 4

position DIP switch] internal style), a HAYES brand Optima 336 external, a HAYES brand Optima 24

Plus FAX96, or an Ademco CIA Modem.

• Compass Downloader for Windows (at revision level supporting LYNXR, LYNXR24 or LYNXR-EN).

Initial Download: Enter Installer Code + # + 5. This sets field ✻95 to 4 rings, and system to “no call-back”

option. The download computer can then call the subscriber, make connection, and download all

programming data.

Flexible Callback: If enabled in field ✻93, the download operator can temporarily change the last 1, 2, or 3

digits (depending on selection) of the call back number. This allows the control to call back a computer other

than the one programmed, which may be helpful at times of high computer traffic. See field ✻93 for a full

description.

Remote Programming Information

LYNX must be connected to the telephone line if using Remote Programming.

The downloading system can perform many functions when in communication with the Control. Besides

uploading and downloading, the status of the system can be observed and various commands can be

initiated, as follows:

• Arm the system in the away mode; disarm the system.

• Bypass a zone.

• Force the system to accept a new program download.

• Shut down communication (dialer) functions (for nonpayment of monitoring fees in an owned system).

• Shut down all security system functions (for nonpayment for a leased system).

• Inhibit local keypad programming (prevents account takeover).

–45–

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote Programming/Control (Downloading)

• Command the system to upload a copy of its resident program to the office.

• Set the time

• View/Modify

• X-10/ Scheduling

• Read: arming status, AC power status, lists of faulted zones, bypassed zones, zones currently in alarm,

zones currently in trouble, and RF sensors with low battery conditions; read control’s time.

Notes: (1) After the control and the PC have established valid communication, the keypad will become inactive and will display “CC.”

(2) The keypad will become active after the download communication is terminated.

(3) The detailed operation of the download functions is covered in the installation instructions for the Compass Downloader for

Windows.

Remote Programming Advisory Notes

• Keypad entries are ignored during the time interval stated above.

• A copy of the program downloaded may be printed using the IBM PC-compatible computer’s internal

report generator, when an optional printer is connected (consult your PC manual for proper printer and

connections).

• Program upload or download time is approximately one minute, fifteen seconds for a complete program.

–46–

Download from Www.Somanuals.com. All Manuals Search And Download.

System Operation

Security Codes

Installer Code

The installer programs the 4-digit Installer Code initially as part of the programming procedure. The

factory default Installer Code is 4-1-1-2, but may be changed in field ✻20.

The Installer Code is the only code that can enter Programming mode and also, in normal operation

mode, is used to enter the Master Code, which allows access to the normal functions of the system.

Master Code

In normal operation mode, the Installer Code is used to enter the 4-digit Master Security Code.

To enter/change the Master code by installer, using the keypad enter:

Installer Code + [CODE key] + [02] + desired 4-digit Master Code

To change the Master code by master, using the keypad enter:

Current Master Code + [CODE key] + [02] + new Master Code + new Master Code again

Secondary User Codes

In normal operation mode, the Master Security Code can be used to assign up to 6 secondary 4-digit security

codes, including a Babysitter Code and a Duress Code. The Master Code can also be used to remove

secondary codes from the system (individually).

To assign (or change) a secondary security code, using the keypad enter:

Master Code + [CODE key] + User # (03–08) + desired Secondary Code

The system will emit a single beep when each secondary code has been successfully entered.

To delete a secondary security code, using the keypad enter:

Master Code + [CODE key] + User # (03–08)

Security Code Notes

•

The Master and Secondary security codes permit access to the system for arming, disarming, etc.

The Installer Code can disarm the system only if it was used to arm it. In addition, the Installer Code cannot disarm

the system if it was armed by pressing and holding a Quick-Arm button.

•

The Babysitter Code (User Code No. 7) can disarm the system only if it was used to arm it. In addition, the

Babysitter Code cannot disarm the system if it was armed by pressing and holding a Quick-Arm button.

Duress code (User Code No. 8) sends a special code to the monitoring station when used to perform any system

operation.. Instruct users to be careful not to use this code for normal usage.

•

If a secondary code is inadvertently repeated for different users, the lower user number will take priority.

Opening/closing reports are sent for the Installer Code as No. 01, with the appropriate subscriber number. Master

Code and set of secondary user codes are sent as Nos. 02 and 03–08, respectively, in Contact ID® format (with the

appropriate user number); in 4+2, it is 1–8. Quick arming (and open/close executed by downloader) is reported as

user 00.

Panic Keys

There are three panic key pairs that, if programmed, can be used to manually initiate alarms and send a

report to the central station.

Each can be individually programmed for 24-hour silent, audible, personal or fire emergency responses. The

panic function is activated when both keys of the appropriate key pair are pressed at the same time.

The panic functions are identified by the system as follows:

Keys

Displayed as Zone

Important: For the silent panic functions

to be of practical value, the system must be

connected to a central station.

[1] & [✻]

[✻] & [#]

[3] & [#]

–47–

Download from Www.Somanuals.com. All Manuals Search And Download.

System Operation

Keypad Functions

The keypad allows the user to arm and disarm the system, and perform other system functions, such as

bypassing zones. Zone and system conditions (alarm, trouble, bypass) are displayed in the display window.

When an alarm occurs, keypad sounding and external sounding will occur, and the zone(s) in alarm will be

displayed on the keypad. Pressing any key will silence the keypad sounder for 10 seconds (only once).

Disarming the system will silence both keypad and external sounders. When the system is disarmed, any

zones that were in an alarm condition during the armed period will be displayed (memory of alarm). To

clear this display, simply repeat the disarm sequence (enter the security code and press the OFF key). The

keypad also features chime annunciation, and 3 panic key pairs for silent, audible, fire or personal

emergency alarms. These keys can notify the central station of an alarm condition, if that service is

connected. A summary of system functions is provided below for more detailed information refer to the

User’s Manual.

Security Functions (Empty boxes represent the user’s security code)

Checking system status: STATUS (high level messages); press STATUS again for secondary messages

To arm in STAY mode:

STAY (or installer code + [3])

To restart exit delay:

STAY (applies only if system is armed in Stay mode)

To arm in AWAY mode:

AWAY (or installer code + [2])

To arm with NO DELAY:

AWAY or STAY

NO DELAY

To arm if Quick Arm is programmed:

AWAY or STAY (hold down for at least 2 seconds)

To disarm the system and silence alarms:

OFF

To bypass a zone(s):

BYPASS + 2-digit zone number(s)

To turn Chime mode on or off:

FUNCTION

CHIME

Message Center

To record a message: FUNCTION

NOTE

RECORD

FUNCTION

RECORD

If a 5827 Wireless keypad has been installed, it cannot be used to

activate message playback/recording, programming the real time clock

or scheduling remotely. In this case, you must use the master keypad on

the control panel to perform these functions.

To stop recording before end of 20 seconds: OFF

To play back a message: FUNCTION

To skip a message: [✻]

PLAY

To delete all messages: ^FUNCTION

Volume Control

DELETE (during message replay)

To adjust message playback/system announcement volume: FUNCTION

VOLUME + [3] or [6]

To mute system announcements:

FUNCTION

VOLUME

OFF

To restore/unmute announcement & volume:

FUNCTION

VOLUME + [3] or [6]

Other Functions

To set the time and date:

FUNCTION + [63]

FUNCTION + [64]

To set the scheduling:

To activate or deactivate X-10 devices 1-6:

To activate or deactivate X-10 devices 7 & 8:

FUNCTION

LIGHTS ON or LIGHTS OFF + device number

FUNCTION + LIGHTS ON or LIGHTS OFF + dev. No.

To add a user code:

*+ CODE + user number + user’s code (*master code)

*+ CODE + user number (* master code)

To delete a user code (except Master Code):

To turn Test mode on:

To turn Test mode off:

TEST

OFF

To use the defined AUX function: Press and hold AUX key 2 secs (4 beeps) +

To define AUX function: AUX + action separated by + AUX terminated by + AUX + AUX

FUNCTION

To send message to pager: Press and hold AUX key 2 seconds (4 beeps)

To program Follow Me Announcement telephone number:

–48–

FUNCTION + [65]

Download from Www.Somanuals.com. All Manuals Search And Download.

System Operation

Speaker Phone Operation (LYNXR-EN Only)

NOTE

The ARMED and READY LEDs blink alternately

when the Speaker Phone is active.

To place a call or answer a call using the speaker phone: [#] + AUX

To flash (switch between two calls using call waiting): AUX

To hang up and exit speaker phone mode: OFF

To enable/disable (toggle) ringer: [#] + VOLUME

AUX

To return the keypad to telephone mode after disarming the system: [#] + AUX

Remote Phone Control Feature

The remote phone control feature, which must be enabled in field ✻91, allows the user to access the security

system from any off-site touch-tone telephone. The control will pick up the incoming call, based on the ring

count specified in field ✻95, and will announce “SYTEM” every three (3) seconds for the next eight (8)

seconds. During this period the panel will wait for a valid User Code to be entered. If a valid User Code is

not entered or the eight (8) second period expires a modem tone will be generated for remote programming

(Compass Downloading). If a valid User Code has been entered, the control will announce the current system

status and/or beeping sounds.

Keypad Functions

Remote Phone Control Feature

To remotely disarm system:

Quick Arm Note

The installer code and

babysitter code cannot

disarm the system if

armed by Quick Arm

method.

+ [1]

To remotely arm in AWAY mode:

To remotely arm in STAY mode:

+ [2]

+ [3]

To remotely arm in AWAY or STAY with no delay:

+ [2] or [3] + [0]

To remotely activate X-10 devices 1-6: [#] + [4] + device no.

To remotely activate X-10 devices 7 & 8:

+ [#] + [4] + device no.

To remotely deactivate X-10 devices 1-6: [#] + [7] + device no.

To remotely deactivate X-10 devices 7 & 8:

+ [#] + [7] + device no.

+ [6] + zone no.

+ [6] + [#]

To remotely Bypass zones:

To remotely activate Forced Bypass:

To remotely check system status: [✻]

To end remote phone control session: Hang Up or

+ [9]

–49–

Download from Www.Somanuals.com. All Manuals Search And Download.

System Operation

Alarm audio verification cannot be used for UL installations.

Alarm Audio Verification (Two-Way Voice Feature)

This feature allows the central station operator to listen, talk to or conduct a two-way conversation with an

individual(s) at the premises. It also assists the operator in gathering information about the nature and

location of the alarm that may be helpful in responding to police and fire departments. All LYNXR-Series

control panels are capable of supporting the Two-Way Voice feature, however only the LYNXR-EN has this

feature built in. The LYNXR/LYNXR24 requires the installation of the Audio Verification Module (LYNX-

AVM). For further information regarding the LYNXR/LYNXR24 Two Way Voice Feature refer to the LYNX-

AVM Installation and Setup Guide. The LYNXR-EN does not make system announcements when the Two-

Way voice feature is active.

Activation

The LYNXR-EN sends the “alarm message” followed by a “Listen-in-to-Follow message” (Contact ID® code

606) to the Central Station. The Listen-in-to-Follow message causes the Central Station’s digital receiver to

temporarily hold the phone line for approximately 1-minute. When the LYNXR-EN receives the “kissoff”

from the central station, indicating that the alarm message has been received, the Two-Way Voice (AVM)

feature is activated in the (default) “Listen Mode” and sirens and keypad sounds are discontinued. The

LYNXR-EN transmits a beep acknowledgment to the Central Station, once per second. The beep alternates

between two tones and indicates that the LYNXR-EN is waiting for a session command from the Central

Station operator. Once a command is issued the beep acknowledgement is discontinued, however, if a

command is not issued within two minutes the system will “time out” and the call will be terminated.

Operator Commands

The Central Station operator begins the session, which last 5 minutes, by entering one of the valid AVM

commands shown in the table below. The session may be extended 5 minutes, without changing the

operating mode, by pressing the [7] key on the touch-tone phone. Selecting another operating mode also

resets the session an additional 5 minutes. During the last minute of the 5 minute, session, the LYNXR-EN

generates two beeps every 30 seconds to alert the Central Station operator that the session is about to time

out. The Central Station operator may then extend the session by pressing the [7] key on the touch-tone

phone. If the session is not extended the phone line is disconnected, and the session is ended. Sessions may

be ended at any time by pressing the [9] key on the touch-tone phone. The AVM modes are described as

follows:

Note: When entering AVM commands make sure the Central Station receiver has been disconnected from the phone line, otherwise

AVM commands may not go through.

Key

Function

Talk Mode: Pressing the [1] key on the touch tone phone, enables one-way voice communication from the central station

to the violated premises, and allows the operator to talk communicate through the LYNXR-EN speaker. In this mode the

ARMED (red) and READY (green) LEDs blink alternately.

VOX (Voice) Mode: Pressing the [2] key on the touch-tone phone, enables two-way voice communications between the central

station and the violated premises. In this mode the ARMED (red) and READY (green) LEDs blink alternately.

Listen Mode: Pressing the [3] key on the touch-tone phone, enables one-way audio from the violated premises to the central

station. The Listen Mode is the start up default mode of the voice feature and allows the operator to listen through the

LYNXR-EN microphone. This mode does not affect the existing LED pattern.

Extends the session 5 minutes without changing its operating mode.

Ends the session and disconnects the phone line.

–50–

Download from Www.Somanuals.com. All Manuals Search And Download.

System Operation

“Follow Me” Reminder Feature

This feature allows the user to schedule a time driven message. When activated the system will dial a phone number, that the

installer programs in Field ✻46, and deliver a voice message (custom words 72, 73, and 74). The LYNXR will immediately

begin transmitting the voice message and will repeat the message for 45 seconds. Pressing any touch-tone key on the

answering phone will acknowledge the message ending the session and preventing the system from redialing the programmed

number. Delivery of a reminder message on the local LYNXR keypad will continue. If the message has timed out the system

will redial the programmed number a maximum of seven additional times or until it is acknowledged. Pressing any key on

the LYNXR keypad will terminate (acknowledge) both the follow me reminder and the local reminder announcements.

Notes: (1) This feature is only supported if programmed in field ✻49.

(2) The follow me reminder will be terminated if any other event requires the system to dial out, or if an audible alarm has

occurred, however, delivery of the local schedule reminder message will continue.

“Follow Me” System Announcement Feature

This feature allows the LYNXR to deliver a voice system message to the secondary phone number

programmed by the installer. The LYNXR will first transmit reports to the Central Station and after

receiving its kiss-off the system will dial the secondary phone number and begin transmitting the voice

message. This message is a repeatable system status announcement. Like the Follow Me reminder, pressing

any key on the answering telephone or the local LYNXR keypad will terminate (acknowledge) the message.

The system will dial the secondary phone number a maximum of eight times. The Follow Me alarm

functions may be triggered by a variety of events depending upon the selections made during programming

in field ✻49.

Note: The follow me system announcement will be terminated if any other event requires the system to dial out or if an

audible alarm has occurred.

Powerline Carrier Devices (e.g. X-10 devices)

If Powerline Carrier Devices are used, two keypad entries available to the user are included. They

can manually activate or deactivate the device(s) for starting or stopping some action, such as

turning lights on or off, etc.

These keypad entries are:

Security Code* + [#] + [4] + Device # activates (starts) that device.

Security Code* + [#] + [7] + Device # de-activates (stops) that device.

*Code is required for devices 7 and 8. Code is not required for devices 1-6.

Exit Error Alarm Displays

If programmed:

• A display of “CA” and a zone indication will appear if an exit or interior zone contained a fault

during closing at the time the exit delay ended (e.g., exit door left open), but the system was

disarmed during the entry delay time. The alarm sounder and keypad sound continuously, but

stop when the system is disarmed. No message will be transmitted to the central station.

• A display of “EA” and a zone indication will appear if an exit or interior zone contained a fault

during closing at the time the exit delay ended, but the system was NOT disarmed during the

entry delay time. The alarm sounder and keypad sound continuously until the system is

disarmed (or timeout occurs). An Exit Alarm message is sent to the central station.

• The “EA” display, etc. will also result if an alarm from an exit or interior zone occurs within two

minutes after the end of an exit delay.

In any of the above cases, use a second OFF sequence (code plus OFF key) to clear the display.

–51–

Download from Www.Somanuals.com. All Manuals Search And Download.

System Operation

Trouble Conditions

The word “FAULT” on the keypad’s display, accompanied by a rapid “beeping” at the keypad, indicates that

there is a trouble condition in the system. Pressing any key can silence the audible warning sound. Instruct

users to call for service immediately upon seeing any of the following messages.

• “Fault” and “Battery” Displays

• “FAULT” and one or more zone numbers indicates that a problem exists with the displayed zone(s)

and requires attention. After correcting the problem, the display can be cleared by entering the security

code plus the OFF key twice.

• The fault condition may also be caused by some change in the environment that prevents the built-in

receiver from receiving signals from a particular wireless sensor.

• “LOW BAT” with no zone number indicates that the system’s backup battery is weak.

• “LOW BAT” with a zone number and a once-per-45 seconds “beeping” at the keypad indicates that a

low battery condition exists in the wireless sensor displayed (zone “00” indicates a wireless button/keypad).

If the battery is not replaced within 30 days, a “FAULT” display may occur.

• “Fault Zone 93”, along with a flashing “AC” and a once per 45-seconds “beeping” at the keypad indicates

a loss of AC power to the 5842 Wireless Dialer (if this feature is supported by the Wireless Dialer being

installed).

• “Fault Zone 93”, along with a single beep indicates that setup information from the 5842 Wireless Dialer

has not been properly received.

Power Failure

• If there is no display at all, and both indicators are not lit, operating power for the system has

stopped and the system is inoperative.

• If the display is lit and the AC display is off, the system is operating on battery power only.

• During an AC power loss, the backlighting will turn off and the indicators will flicker slightly to

minimize deep discharge of the battery.

Other Displays

dI = Busy-Standby: Displayed upon power-up. After approximately 1 minute* the green “READY” LED

should light. If the “dI” remains displayed for more than 1 minute, the system is disabled.

*To bypass the 1-minute delay, press [#] + [0]. Important: Do not try to bypass 1 minute delay before “dI”

is displayed!

CC = Modem Comm: The system is communicating with the central station for change of function or

status verification.

FC = Comm. Failure: A communication failure has occurred. This message clears only when the system

is subsequently armed.

90 = RF Jam: The system has detected an RF jamming condition or excessive interference.

93 = Wireless Dialer: Tamper (alarm or trouble), phone line cut, loss of supervision, low battery, or AC

power loss*.

*If supported by the 5842 Wire Dialer that is installed.

PH = Speaker Phone Mode: The system is in Speaker Phone mode.

PC = Phone Control: The remote Phone Control feature is active.

“ -- ” Displayed when entering programming mode if a 5842 Wireless Dialer is enabled.

–52–

Download from Www.Somanuals.com. All Manuals Search And Download.

Testing the System

Test Mode

After installation is completed, the security system should be carefully tested, as follows.

1. With the system in the disarmed state, check that all zones are intact. If the READY LED is

not lit, press the [ ✻] key to display the faulted zone(s). Restore faulted zone(s) if necessary, so

that READY LED lights. Fault and restore every sensor individually to assure that it is being

monitored by the system.

2. Enter the security code and press the TEST key. The outside sounder will sound for 1 second

and all the LED segments on the keypad display light for 3 seconds. LYNX announces the

zone’s voice descriptor (if programmed) followed by 3 beeps, each time a contact is faulted. A

test report should be transmitted (if programmed) to the central station immediately. If the

backup battery is discharged or missing, the sounder may not turn on and a LOW BATTERY

report will be transmitted with a TEST report. The keypad will beep once every 45 seconds as a

reminder that the system is in the Test mode.

3. To turn off the Test mode enter security code and press the OFF key.

Notes: (1) Triggering a zone set to Arm AWAY, Arm STAY, or Disarm will take the system out of Test and

cause that action.

(2) BR type transmitters do not display during Test mode (keypad beeps only)

(3) Macros cannot be run from the Test mode.

Armed System Test

Alarm messages will be sent to the central station during the following tests 1 and 2.

Notify them in advance that tests will be in progress.

1. Arm the system and fault one or more zones. After 15 seconds (if optional dialer delay is

selected), silence alarm sounder(s) by entering the code and pressing OFF. Check entry/exit

delay zones.

2. Check the keypad-initiated alarms that are in the system by pressing the Panic key pairs. If the

system has been programmed for audible emergency, the keypad will emit a steady alarm

sound, and “ALARM” and zone number will be displayed. Silence the alarm by entering the

security code and pressing OFF.

If the system has been programmed for silent emergency, there will be no audible alarms or

displays, but a report will be sent to the central station.

3. If Powerline Carrier Devices have been installed, test their programmed action.

4. Notify the central station when all tests are finished, and verify results with them.

5. To test the wireless part of the system and the RF receiver, perform the two additional tests

described in the Installing Wireless Zones section: Sniffer mode and Go/No Go Test.

Note: System Test mode (installer/master code + test) and Go/No Go Test (installer code + # + 8) will

be automatically terminated after 3-1/2 to 4 hours if the installer or user does not manually

terminate it. This ensures that fire and panic zones will not remain disabled. However, Sniffer

mode (installer code + # + 3) does not automatically expire. You must manually exit

(Installer/User Code + OFF) Sniffer mode to return to normal operation.

TO THE INSTALLER

Regular maintenance and inspection (at least annually) by the installer and frequent testing by the

user are vital to continuous satisfactory operation of any alarm system.

The installer should assume the responsibility of developing and offering a regular maintenance

program to the user as well as acquainting the user with the proper operation and limitations of the

alarm system and its component parts. Recommendations must be included for a specific program of

frequent testing (at least weekly) to ensure the system’s proper operation at all times.

–53–

Download from Www.Somanuals.com. All Manuals Search And Download.

System Communication

This section provides an explanation of formats this system accommodates for reporting alarms and

other system conditions to the central station. The process of a successful transmission consists of

both the method of communication between the control panel and the central station receiver, and

the actual way the information is sent and displayed at the central station.

Communication Overview

When the panel calls the central station receiver, it waits to hear a “handshake” frequency from the

receiver to confirm that the receiver is on-line and ready to receive its message. Once the panel

hears the handshake it is programmed to listen for, it sends its message. The panel then waits for a

“kissoff” frequency from the receiver acknowledging that the message was received and understood.

If the handshake frequency is not given or is not understood by the panel, the panel will not send its

message. Once the handshake frequency is received and understood by the panel, the panel will

send its message. If there is an error in the transmission (the receiver does not receive a “valid”

message), the kissoff frequency will not be given by the central station receiver.

The panel will make eight attempts to the primary telephone number and eight attempts to the

secondary telephone number (if programmed) to get a valid message through. If the panel is not

successful after its numerous attempts, the keypad will display “FC.” If the secondary number is a

pager, “FC” displays after the first 8 attempts to the primary number.

The following chart defines the three sets of (handshake/kissoff) frequencies that the panel supports, and

the different formats that can be sent for each.

FORMAT

Low Speed

3+1

HANDSHAKE

1400Hz

TRANSMITS DATA KISSOFF

TRANSMIT TIME

Under 15 seconds

1900Hz (10PPS)

1400Hz

(Standard report)

4+1

4+2

Sescoa/Rad

3+1

2300Hz

1900Hz (20PPS)

(Standard report)

2300Hz

Under 10 seconds

4+1

4+2

Express

4+2

Contact ID®

1400–2300Hz

DTMF (10 cps)

1400Hz

Under 3 seconds

Report Code Formats

3+1 and 4+1 Standard Formats Comprise a 3- (or 4-) digit subscriber number and a single digit report

code (e.g. alarm, trouble, restore, open, close, etc).

3+1 and 4+1 Expanded Formats Comprise a 3- (or 4-) digit subscriber number, and a 2-digit report

code. The first digit is displayed on the first line, followed by a second

line where the first digit is repeated 3 (or 4) times and followed by the

second digit. This is the “expanded” digit.

4+2 Format

Comprises a 4-digit subscriber number and 2-digit report code.

ADEMCO Contact ID®

Reporting Format

Comprises a 4-digit subscriber number, 1-digit event qualifier

(“new” or “restore”), 3-digit event code, and 3-digit zone number, user

number, or system status number (see the following page).

The following table shows the message formats for 3+1, 4+1 and 4+2 reports, where:

SSS or SSSS

Subscriber ID

Alarm Code (1st digit)

Typically Zone Number* (2nd digit)

Trouble Code (1st & 2nd digits)

Bypass Code (1st & 2nd digits)

C = Close Code (1st Digit)

User Number (in hex)

Test Code (1st & 2nd digits)

Alarm Restore Code

Trouble Restore Code (1st & 2nd digits)

AC Loss Code (1st & 2nd digits)

Low Battery Code (1st & 2nd digits)

Open Code (1st Digit)

Bypass Restore Code (1st & 2nd digits)

AC Restore Code (1st & 2nd digits)

Battery Restore Code (1st & 2nd digits)

*Zone numbers for: [ ] & [#], or [B] = 99; [1] + [ ], or [A] = 95; [3] + [#], or [C] = 96; Duress = 92

–54–

Download from Www.Somanuals.com. All Manuals Search And Download.

System Communication

Report

3+1/4+1 Standard

3+1/4+1 Expanded

4+2

Alarm

SSS(S) A

AAA(A) Z

SSS(S) T

TTT(T) t

SSS(S) B

BBB(B) b

SSS(S) E

SSSS AZ

Trouble

Bypass

AC Loss

SSS(S) T

SSS(S) B

SSS(S) E

SSSS Tt

SSSS Bb

SSSS EA

EEE(E) A

Low Battery

SSS(S) L

LLL(L) L

SSSS LL

Open

SSS(S) O

SSS(S) C

SSS(S) G

SSS(S) R

SSS(S) O

OOO(O) U

SSS(S) C

CCC(R) U

SSS(S) G

GGG(G)g

SSS(S) R

RRR(R) Z

SSSS OU

SSSS CU

SSSS Gg

SSSS RZ

Test

Restore Alarm

AC Restore

SSS(S) R

SSSSR

R R R (R )A

A A A

Low Battery Restore

Trouble Restore

Bypass Restore

SSS(S) R

SSSS R L

L B

R R R (R )L

L L L

SSS(S) R

SSSS R t

R R R (R )t

T T T

SSS(S) R

SSSS R b

R R R (R )b

B B B

ADEMCO Contact ID® Reporting takes the following format: CCCC Q EEE GG ZZZ where:

CCCC = Customer (subscriber) ID

Q =

Event qualifier, where: E = new event, and R = restore

Event code (3 hex digits) (for a complete list of event codes, refer to the central office receiver manual)

Always “00”

Zone/Contact ID® number reporting the alarm, or user number for open/close reports. System

status messages (AC Loss, Walk Test, etc.) contain zeroes in the ZZZ location.

EEE =

GG =

ZZZ =

CONTACT ID® EVENT CODES

Code

110

121

122

123

131

132

134

135

145

146

150

301

338

341

342*

344

351*

354

355

Definition

Code

380

381

383

384

401

Definition

Fire Alarm

Duress

Alarm, 24-hour Silent

Global Trouble, Trouble Day/Night

RF Supervision Trouble

RF Sensor Tamper (Trouble)

RF Sensor Low Battery

Disarmed, Armed AWAY (NO DELAY),

Armed AWAY

Alarm, 24-hour Audible

Alarm, Perimeter

Alarm, Interior

Alarm, Entry/Exit

Alarm, Day/Night

403

406

407

408

Scheduled Auto Arm

Cancel by User

Remote Arm/Disarm (Downloading)

Quick Arm AWAY/NO DELAY

Wireless Dialer Tamper (plus Zone 93) (Alarm)

Silent Burglary

Alarm, 24-Hour Auxiliary

AC Power

441

Disarmed/Armed STAY/NO DELAY, Quick Arm

STAY/NO DELAY

Bypass

Periodic Test

AAV to follow

System Test

Event Log 80% Full

System Inactivity

Wireless Dialer Low Battery (plus Zone 93)

Wireless Dialer Tamper (plus Zone 93) (Trouble)

Wireless Dialer AC Loss (plus Zone 93)

RF Jam Detected

Wireless Dialer Phone Line Cut (plus Zone 93)

Fail to Report

570

602

606

607

623

654

Wireless Dialer Loss of RF Supervision

(plus Zone 93)

NOTE: The following codes are logged in the event log upon

occurrence, but are not reported:

355

373

374

(Zone 000) Reported by the 5842 Wireless Dialer

Fire Loop Trouble

305 = System Reset

627 = Keypad Program Mode Entry

Exit Error Alarm

*If supported by the 5842 Wireless Dialer that is installed.

–55–

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting Guide

S Y S T E M ( i n c l u d i n g W i r e l e s s )

SYMPTOM

POSSIBLE CAUSE

REMEDY

1a. Transmitter not properly powered.

1a Check or change transmitter's battery.

1. Transmitter signal

not received at

control.

1b. If Transmitter is 5827, House Code not

set in field ✻24, or transmitter is not set

to same House Code set in that field.

1b. Check code switches inside transmitter.

Must match with RF House Code

programmed.

1c. Transmitter is located too far from RF

receiver.

1c. Move transmitter or RF receiver.

1d. There is metal shielding between

transmitter and RF receiver.

1d. Check for large metal obstructions, then

relocate transmitter if necessary.

1e. Transmitter is malfunctioning.

1e. Verify by activating control with

another, similar transmitter. If O.K.

now, return defective transmitter.

1f. Transmitter No. (zone) is not

programmed.

1f. Verify programming.

2a. Transmitter zone type (ZT) is set to 00

(Not Used).

2a. Set ZT to a valid active zone type in

2. Transmitter zone

number appears

during Transmitter

Sniffer mode, but

does not clear.

field ✻56.

2b. Transmitter battery not installed.

2b. Install proper battery.

2c. 5800 System transmitter not "entered" in

system.

2c. "Enter" unit in field ✻56 or ✻83.

3. Low battery message

on keypad.

3a. "Low Bat" (no zone Nos.)

3b. "Low Bat" + "00".

3a. System battery is low or missing.

3a. Replace system battery.

3b. Remote RF keypad/button battery is low. 3b. Replace battery in the RF keypad.

3c. "Low Bat" + "nn".

3c. Transmitter for zone “nn” has a low

battery.

3c. Replace the battery in the displayed

transmitter.

4a. System is in Test mode.

4a. Enter Code + OFF to exit Test mode.

4. Periodic beep(s) from

keypad.

4b. A transmitter low battery has occurred

and is displayed.

4b. Enter Code + OFF and replace the

battery.

4c. Check the transmitter indicated.

Restore communication to the receiver

to cancel the condition.

4c. A supervision fault has occurred.

4d. System low battery

4d. Replace system battery

Put control in Test mode. If zone does not

respond, try operating the tamper switch or

another input to the transmitter.

5. With 5800 System,

there is no response

to a transmitter in

normal operation,

although zone

5a. If another input causes the zone to be

displayed, the wrong input was "entered"

when programming.

5a. Delete input's serial number (not the

zone), and enter the proper input (see

field ✻56).

number clears during

Transmitter Sniffer

mode.

5b. If no response at all from this

transmitter, this physical transmitter

has not been entered by the system.

Transmitter Sniffer display is being

cleared by another unit programmed for

this zone.

5b. Determine which transmitter is

programmed for this zone and

reprogram as necessary.

6a. Sensors not properly installed, wired, or

monitored.

6a. Check installation to see if in

6. Nuisance or phantom

alarm.

accordance with established procedure.

6b. Universal transmitter (5817)

programmed wrong.

6b. Check programming switches on

transmitter.

7a. Protected door or window opened while

system armed.

7a. Check with all occupants of protected

home.

7. Intrusion alarm for

no apparent reason.

7b. Improper user operation of exit/entry

delays.

7b. Check setting of entry and exit delays.

7c. Magnets located too far from switches,

and/or doors and windows not properly

aligned.

7c. Check all openings for proper switch

and magnet orientation.

–56–

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting Guide

C O N T R O L

SYMPTOM

POSSIBLE CAUSE

REMEDY

1a. Interrupted AC power supply.

1a. Check transformer connection and

powerline circuit breaker.

1. The word “AC” is not

displayed.

2a. System in Test mode.

2b. Telephone connection not secure.

2c. Digital communicator

malfunctioning.

2a. Remove from Test mode.

2b. Check all connections.

2c. Check with a different CONTROL

PANEL.

2. Digital communicator

message not being

received.

2d. Program prefix or access code into the

CONTROL PANEL.

2e. System cannot work in this situation.

2d. Telephone number in program needs

prefix or access code.

2e. Telephone call to central monitoring

station requires operator assistance.

3. Does not arm properly.

Open or faulted zone(s)

Check for faulted zones and make intact,

or use Bypass arming, if desired.

READY light not on.

4. System doesn't respond to

keystrokes on keypad.

4a. System is in communication with

downloader at central station.

4a. Wait until download session is

finished.

4a. "CC" displayed.

4b. System has just been powered and is

in its one minute initialization.

4b. "d1" displayed.

4b. Wait for initialization to finish, or

bypass this time by pressing '#' + '0.'

S M O K E D E T E C T O R

SYMPTOM

POSSIBLE CAUSE

REMEDY

1. Detector alarms, no

apparent reason.

1a. Dust, dirt in sensing chamber.

1a. Clean unit's sensing

chamber with vacuum

cleaner per unit's

1b. Improper location.

instructions.

1b. See unit's instructions

for locations to avoid.

1c. Unit malfunctioning.

Relocate as necessary.

1c. Replace detector.

2. Detector's siren sounds.

2a. Unit not receiving required power.

2b. Unit malfunctioning.

2a. Check for proper

installation of battery.

Try new battery.

2b. Replace detector.

–57–

Download from Www.Somanuals.com. All Manuals Search And Download.

Contacting Technical Support

PLEASE, before you call Technical Support, be sure you:

•

READ THE INSTRUCTIONS!

Check all wiring connections.

Determine that the power supply and/or backup battery are supplying proper voltages.

Verify your programming information where applicable.

Note the proper model number of this product, and the version level (if known) along with

any documentation that came with the product.

•

Note your ADEMCO customer number and/or company name.

Having this information handy will make it easier for us to serve you quickly and effectively.

You may contact Technical Support via Toll Free Fax. Please include your return fax number. You will

receive a reply within 24 hours.

Technical Support: ..................................................................... 1-800-645-7492 (8 a.m.-8 p.m. E.S.T.)

FAX FAXBACK Automated Fax Retrieval System:.................... 1-800-573-0153 or 1-516-921-6704 / ext. 1667

World Wide Web Address: ........................................................... http://www.ademco.com

–58–

Download from Www.Somanuals.com. All Manuals Search And Download.

Regulatory Agency Statements

UL NOTICE: This is a "Grade A" residential system.

FCC ID: CFS8DLLYNXREN-2

CANADA: 1748A-LYNXREN2

FCC STATEMENT

THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1)

THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE

RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

Federal Communications Commission (FCC) Part 15 Statement

This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following

statement for your information:

This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with

the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to

comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are

designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

•

If using an indoor antenna, have a quality outdoor antenna installed.

Reorient the receiving antenna until interference is reduced or eliminated.

Move the radio or television receiver away from the receiver/control.

Move the antenna leads away from any wire runs to the receiver/control.

Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits.

If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user

or installer may find the following booklet prepared by the Federal Communications Commission helpful: "Interference Handbook."

This booklet is available from the U.S. Government Printing Office, Washington, DC 20402.

The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's

Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment.

Federal Communications Commission (FCC) Part 68

This equipment complies with Part 68 of the FCC rules. On the front cover of this equipment is a label that contains the FCC

registration number and Ringer Equivalence Number (REN). You must provide this information to the telephone company when

requested.

This equipment uses the following USOC jack: RJ31X

This equipment may not be used on telephone-company-provided coin service. Connection to party lines is subject to state tariffs.

This equipment is hearing-aid compatible.

Industry Canada

NOTICE: The Industry Canada Label identifies certified equipment. This certification means that the equipment meets

telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment

Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local

telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer

should be aware that compliance with the above conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations

made by the user to this equipment, or equipment malfunctions, may give the telecommunications company to request the user to

disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal

metallic water pipe system, if present, are connected together, This precaution may be particularly important in rural areas.

Caution: Users should not attempt to make such connections themselves but should contact appropriate electric inspection

authority, or electrician, as appropriate.

Ringer Equivalence Number Notice:

The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of

terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of

devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.

–59–

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

LYNXR-Series

Security

1. Physical: 10-3/8” W x 7-1/8” H x 1-3/4” D

Controls

2. Electrical:

VOLTAGE INPUT: 9VAC from plug-in 15VA transformer.

RECHARGEABLE BACKUP BATTERY: Six 1.2-volt/cell nickel-metal hydride

rated at 1100 mA.

ALARM SOUNDER: Piezo = 6-14VDC, 30mA max/ Bell = 6-14VDC, 120mA max

(e.g., ADEMCO’s WAVE2EX).

LONG RANGE RADIO: Rated 12mA@12-volt nominal (negative trigger signal).

3. Communication:

FORMATS SUPPORTED:

ADEMCO Express, 10 characters/sec, DTMF (TouchTone) Data Tones,

1400/2300Hz ACK, 1400Hz KISSOFF.

ADEMCO Contact ID® Reporting, 10 characters/sec., DTMF (TouchTone)

Data Tones, 1400/2300Hz ACK, 1400Hz KISSOFF.

ADEMCO Low Speed, 10 pulses/sec, 1900Hz Data Tone,

1400Hz ACK/KISSOFF.

Radionics/SESCOA, 20 pulses/sec, 1800Hz Data Tone, 2300Hz

ACK/KISSOFF. Can report 0–9, B–F.

Line Seize: Double Pole

Ringer Equivalence: 0.6B

FCC Registration No.: 5GBUSA-25623-AL-E

4. Maximum Zone 1 Resistance: 300 ohms, excluding 2k ohm EOLR

–60–

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR/LYNXR24 PROGRAMMING DEFAULT TABLES

(boldface indicates defaults that differ between tables)

Function

Table 1

Table 2

Table 3

Table 4

*20

*21

*22

*23

*24

*25

*26

*27

*29

*30

Installer code

Quick arm enable

Keypad backlight timeout

Forced bypass

RF house ID code

Powerline carrier device house code

Chime-by-zone

Real-time clock display

Daylight saving time start/end month

Daylight saving time start/end weekend

4112

0,0

4112

0,0

4112

0,0

4112

0,0

4,10

1,5

4,10

1,5

4,10

1,5

4,10

1,5

*31 Single alarm sounding per zone

*32

*33

*34

*35

*36

*37

*38

*39

*40

*41

*42

*43

*44

*46

*47

*48

*49

*50

*51

*52

*53

*54

*55

*56

*58

*59

*60

*61

*62

*63

*64

*65

*66

*67

*68

*70

*71

*72

*73

*74

*75

*76

*80

*81

*84

*87

*88

*89

*90

*91

*92

*93

*94

*95

Fire sounder timeout

Alarm bell timeout

Exit delay

Entry delay 1 (zone type 01)

Entry delay 2 (zone type 02)

Audible exit warning/quick exit

Confirmation of arming ding

Power up in previous state

PABX access code

7,0

3,0

6,0

1,1

6,0

4,5

6,0

0,1

7,0

3,0

6,0

1,1

7,0

3,0

6,0

1,1

---

Primary phone number

Secondary phone number

Primary subscriber account number

Secondary subscriber account number

“Follow Me Reminder” Phone Number

Phone system select

Report format

Split/dual reporting

15 second dialer delay (burglary)

Periodic test report

First test report offset

Sescoa/radionics select

Lack of usage notification

Wireless Dialer

Enhanced Zone programming

RF jam detection

Exit error report code

Trouble report code

Bypass report code

AC loss report code

15,15,15,15

---

7,7

---

7,7

---

7,7

---

7,7

0, 0, 0, 0

See *56 table

0, 0, 0, 0

See *56 table

0, 0, 0, 0

See *56 table

0, 0, 0, 0

See *56 table

1,0

0,0

1,0

0,0

1,0

0,0

1,0

0,0

1,0

0,0

1,0

0,0

1,0

0,0

1,0

0,0

1,0

0,0

1,0

0,0

1,0

0,0

1,0

0,0

1,0

Low battery Report code

Test report code

Open report code

Arm away/stay report code

RF transmitter low battery report code

Cancel report code

Alarm restore codes

Trouble restore report code

Bypass restore report code

AC restore report code

Low battery restore report code

RF transmitter low battery restore report code

Test restore report code

Powerline Carrier Devices

Zone lists for devices

Assign zone voice descriptors

Auxiliary Function/ 1-button paging

Pager characters

Event log 80% full report code

Event logging

0,0

1,0

0,0

See *80 table

See *81 table

See *80 table

See *81 table

Refer to *84 Programming

See *80 table

See *81 table

See *80 table

See *81 table

---

0,0

---

1,2,3,4

---

0,0

---

0,0

---

1,2,3,4

---

0,0

---

1,2,3,4

---

LRR/AAV Trigger/Remote Phone Control

Number of reports in armed period

Flexible call back

Download phone number

Ring detect count for downloading/remote phone control

1,2,3,4

---

Default Master Code

Default Duress Code

By activating *96, Field 43, and 44 will be changed to 15, 15, 15, 15.

– 61 –

Download from Www.Somanuals.com. All Manuals Search And Download.

LYNXR-EN PROGRAMMING DEFAULT TABLES

(boldface indicates defaults that differ between tables)

Function

Table 1

Table 2

Table 3

Table 4

*20 Installer code

4112

*21 Quick arm enable

*22 Keypad backlight timeout

*23 Forced bypass

*24 RF house ID code

0,0

*25 Powerline carrier device house code

*26 Chime-by-zone

*27 Real-time clock display

*29 Daylight saving time start/end month

*30 Daylight saving time start/end weekend

*31 Single alarm sounding per zone

*32 Fire sounder timeout

4,10

1,5

4,10

1,5

4,10

1,5

4,10

1,5

*33 Alarm bell timeout

*34 Exit delay

7,0

6,0

7,0

*35 Entry delay 1 (zone type 01)

*36 Entry delay 2 (zone type 02)

*37 Audible exit warning/quick exit

*38 Confirmation of arming ding

*39 Power up in previous state

*40 PABX access code

3,0

6,0

1,1

---

4,5

6,0

0,1

---

3,0

6,0

1,1

---

3,0

6,0

1,1

---

*41 Primary phone number

*42 Secondary phone number

*43 Primary subscriber account number

*44 Secondary subscriber account number

*46 “Follow Me Reminder” Phone Number

*47 Phone system select

---

15,15,15,15

---

*48 Report format

7,7

*49 Split/dual reporting

*50 15 second dialer delay (burglary)

*51 Periodic test report

*52 First test report offset

*53 Sescoa/radionics select

*54 Lack of usage notification

*55 Wireless Dialer

0, 0, 0, 0

*56 Enhanced Zone programming

*58 RF jam detection

See *56 table See *56 table

See *56 table

*59 Exit error report code

*60 Trouble report code

*61 Bypass report code

*62 AC loss report code

*63 Low battery Report code

*64 Test report code

1,0

0,0

1,0

0,0

1,0

0,0

1,0

0,0

1,0

*65 Open report code

*66 Arm away/stay report code

*67 RF transmitter low battery report code

*68 Cancel report code

0,0

1,0

0,0

1,0

0,0

1,0

0,0

1,0

*70 Alarm restore codes

*71 Trouble restore report code

*72 Bypass restore report code

*73 AC restore report code

*74 Low battery restore report code

*75 RF transmitter low battery restore report code

*76 Test restore report code

*80 Powerline Carrier Devices

*81 Zone lists for devices

1,0

0,0

1,0

0,0

1,0

0,0

1,0

0,0

1,0

0,0

---

1,0

0,0

1,0

0,0

See *80 table See *80 table

See *81 table See *81 table

See *80 table

See *81 table

*84 Assign zone voice descriptors

*87 Auxiliary Function/ 1-button paging

*88 Pager characters

Refer to *84 Programming

---

*89 Event log 80% full report code

*90 Event logging

*91 Alarm audio verification/remote phone control

*92 Number of reports in armed period

*93 Flexible call back

0,0

*94 Download phone number

*95 Ring detect count for downloading/remote phone control

Default Master Code

---

1,2,3,4

---

1,2,3,4

---

1,2,3,4

---

1,2,3,4

---

Default Duress Code

By activating *96, Field 43, and 44 will be changed to 15, 15, 15, 15.

– 62 –

Download from Www.Somanuals.com. All Manuals Search And Download.

✻56 ZONE ASSIGNMENT/ALARM REPORT CODES FOR TABLE 1

Zone No. Zone Type Alarm Code

Input Type

Loop Number

Zone Descriptor

0,0

1,0

0,0

1,0

0,0

1,0

---

3 (RF)

5 (BR)

---

47, 04 (FRONT DOOR)

33, 04 (BACK DOOR)

80 (WINDOW)

---

56 (MOTION DETECTOR)

---

NOTE: Zone 1 is a hardwire zone; Zone 2 to 41 are RF zones; Zone 92 is Duress; Zone 99 is keypad panic

✻56 ZONE ASSIGNMENT/ALARM REPORT CODES FOR TABLE 2

Zone No. Zone Type Alarm Code

Input Type

Loop Number

Zone Descriptor

---

0,0

1,0

0,0

1,0

0,0

1,0

---

3 (RF)

5 (BR)

---

47, 04 (FRONT DOOR)

33, 04 (BACK DOOR)

48, 04 (GARAGE DOOR))

56 (MOTION DETECTOR)

22, 02 (SMOKE DETECTOR)

---

NOTE: Zone 1 is a hardwire zone; Zone 2 to 41 are RF zones; Zone 92 is Duress; Zone 99 is keypad panic

✻56 ZONE ASSIGNMENT/ALARM REPORT CODES FOR TABLES 3 & 4

Zone No. Zone Type Alarm Code

Input Type

Loop Number

Zone Descriptor

---

0,0

1,0

0,0

1,0

0,0

1,0

---

3 (RF)

5 (BR)

---

47, 04 (FRONT DOOR)

33, 04 (BACK DOOR)

80 (WINDOW)

56 (MOTION DETECTOR)

22, 02 (SMOKE DETECTOR)

---

NOTE: Zone 1 is a hardwire zone; Zone 2 to 41 are RF zones; Zone 92 is Duress; Zone 99 is keypad panic

– 63 –

Download from Www.Somanuals.com. All Manuals Search And Download.

✻80 DEFAULT TABLE: APPLIES TO DEFAULT TABLE 4 (devices 2-7 have no default values)

Start

Stop

Zone Type

System Operation

Restore of

Zone List

Zone type

System operation

Device Number

Action

Event

Zone List

8**

** NOTE: If using an X-10 Powerhouse Security SH10A siren as device 8, you must change the device action default to “3” if using default

table 4.

✻80 DEFAULT TABLE: APPLIES TO DEFAULT TABLE 1 and 2 (devices 1-7 have no default values)

Start

Stop

Zone Type

System Operation

Restore of

Zone List

Zone type

System operation

Device Number

8**

Action

Event

Zone List

✻81 ZONE LIST FOR OUTPUT DEVICES DEFAULT TABLE: Applies To Default Table 1 - 4.

Zone List 1 28, 32

Zone List 2 29, 33

Zone List 3 2, 3

– 64 –

Download from Www.Somanuals.com. All Manuals Search And Download.

–Index –

*55 Enabling the 5842 Wireless Dialer................................... 25

*56 Enhanced Zone Programming Mode................11, 20, 24, 27

*80 Device Programming Menu Mode....................24, 31, 32, 33

*81 Zone List Menu Mode.................................................. 24, 34

*83 Enhanced Sequential Mode ...........24, 27, 29, 30, 35, 36, 37

*84 Assign Zone Voice Descriptors.........................24, 30, 38, 39

*85 Record Custom Voice Descriptors............................... 24, 40

Babysitter Code........................................................................47

Back Plate...................................................................................5

Backlighting .............................................................................17

Backup Battery...........................................................................9

Backup Reporting.....................................................................18

Battery Life ..............................................................................12

Battery, Low.............................................................................52

Bell............................................................................................60

BR .......................................................................................11, 28

Burglary Zones .........................................................................17

Busy-Standby ...........................................................................52

Button Transmitters ..........................................................11, 12

Button Type..............................................................................28

Button Zones.......................................................................26, 28

Bypass Report Code......................................................21, 61, 62

Bypass Restore Report Code ........................................21, 61, 62

96 Initialize Download ID And Subscriber Acct. No. For

Downloading........................................................................ 24

97 Set All Program Fields To 1 Of 4 Sets Of Default Values 24

98 Exits Programming Mode ................................................. 24

99 Exits Programming Mode ................................................. 24

1.2-Volt Nickel-Metal Hydride Batteries................................. 10

1332CN ...................................................................................... 9

15 Second Dialer Delay................................................ 20, 61, 62

24-Hour Audible Alarm ........................................................... 16

24-Hour Auxiliary Alarm......................................................... 16

24-Hour Silent Alarm ........................................................ 15, 47

5800 Series Transmitters ........................................................ 11

5800RL............................................................................... 11, 13

5801.......................................................................................... 11

5802MN.............................................................................. 11, 12

5802MN2.................................................................................. 12

5804.............................................................................. 11, 12, 35

5804BD......................................................................... 11, 12, 17

5804BDV...................................................................... 11, 12, 17

5804E ................................................................................. 11, 12

5804WATCH............................................................................ 11

5816.................................................................................... 11, 35

5817.......................................................................................... 11

5827.............................................................................. 11, 13, 17

5828V ....................................................................................... 13

5842.......................................................................................... 25

90 ............................................................................................. 52

CA Message Display.................................................................51

Callback Number......................................................................23

Cancel Report Code ............................................................61, 62

Canceled Alarm ........................................................................21

CC .............................................................................................52

Change the Master Code..........................................................47

Chime By Zone .............................................................17, 61, 62

Chime Mode........................................................................17, 48

Closing Report..........................................................................18

Comm. Failure..........................................................................52

Communication ....................................................................4, 54

Compass Downloader...............................................................45

Confirmation of Arming Ding ......................................18, 61, 62

Connecting AC Power and Backup Battery...............................9

Contact ID ................................................................................54

Contact ID Event Codes...........................................................55

Contact ID Format .............................................................21, 47

Contact ID Reporting .........................................................55, 60

Contacting Technical Support..................................................58

Custom Descriptor Number .....................................................40

Custom Voice Descriptors ..................................................24, 40

AC Loss Report Code ................................................... 21, 61, 62

AC Power ................................................................................... 9

AC Power and Rechargeable Backup Battery......................... 10

AC Power Loss........................................................................... 9

AC Restore Report Code .................................................... 61, 62

AC Transformer......................................................................... 6

ADEMCO 1332/1332X10 ........................................................... 9

ADEMCO Express ............................................................. 19, 60

ADEMCO Low Speed......................................................... 19, 60

Alarm Audio Verification (AAV)/Remote Phone Control ........ 23

Alarm Audio Verification (Two-Way Voice Feature)............... 50

Alarm Bell Timeout ..................................................... 17, 61, 62

Alarm Output............................................................................. 4

Alarm Restore Codes ......................................................... 61, 62

Alarm Restore Report Code..................................................... 21

Alarm Sounder......................................................................... 60

Arm Away/Stay Report Code............................................. 61, 62

Arm AWAY/STAY Report Code............................................... 21

Arm–Away ............................................................................... 16

Armed System Test.................................................................. 53

Arm–Stay................................................................................. 16

Assign (Or Change) A Secondary Security Code..................... 47

Assign Custom Voice Descriptors............................................ 40

Assign Zone Voice Descriptors..................................... 38, 61, 62

Audible Exit Warning/Quick Exit ............................... 18, 61, 62

AUX Function .......................................................................... 48

AUX Function/1-Button Paging................................... 22, 61, 62

AUX Key .................................................................................. 22

AWAY Mode............................................................................. 48

Data Encryption.......................................................................45

Data Field.................................................................................14

Daylight Savings Time Start/End................................17, 61, 62

Daylight Savings Time Start/End Week..................................17

Default Master Code ..........................................................61, 62

Default Tables ....................................................................61, 62

Delete a Secondary Security Code ...........................................47

Delete Entire Zone List............................................................34

Delete Zone Parameters Confirmation ..............................29, 37

Delete Zones .............................................................................34

Descriptor ...........................................................................30, 38

Desktop Mounting......................................................................5

Device Action............................................................................33

Device Number.........................................................................33

DI Display.................................................................................52

DIP Switches ............................................................................11

Disable Local Sounder................................................................7

Disarm................................................................................16, 48

Displays ....................................................................................52

Download Call Back Phone Number........................................23

Download Phone Number...................................................61, 62

Download, Initial......................................................................45

Downloader...................................................................22, 45, 46

Duress Code........................................................................47, 63

– 65 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Low Battery Report Code.........................................................21

Low Battery Restore Report Code ............................... 21, 61, 62

Low Speed ................................................................................54

LYNX-DM...................................................................................5

LYNXR/LYNXR24 Programming Default Tables ...................61

LYNXRCHKIT-HC...................................................................10

LYNXRCHKIT-SC ...................................................................10

LYNXR-EN Programming Default Tables ..............................62

EA ............................................................................................ 51

Earth Ground............................................................................. 6

Enabling the 5842 Wireless Dialer ......................................... 25

Enroll Mode ....................................................................... 29, 36

Enter/Change the Master Code............................................... 47

Entry Delay ..................................................................18, 61, 62

Entry/Exit Burglary ................................................................ 15

Error Code 374......................................................................... 21

Event Log 80% Full Report Code .................................22, 61, 62

Event Logging...............................................................22, 61, 62

Exit Alarm ............................................................................... 21

Exit Delay...............................................................17, 18, 61, 62

Exit Delay Restart............................................................. 18, 48

Exit Door.................................................................................. 17

Exit Error Alarm Displays ...................................................... 51

Exit Error Report Code.................................................21, 61, 62

Exit Warning ........................................................................... 18

Exiting Program Mode ............................................................ 14

Expert Programming............................................................... 14

Express .................................................................................... 54

External Sounder..................................................................... 17

Macro Function ........................................................................22

Master Code .............................................................................47

Master Security Code...............................................................17

Memory Of Alarm.....................................................................48

Message Center........................................................................48

Modem Comm...........................................................................52

Mounting Base ...........................................................................5

Mute System Announcements .................................................48

No Alarm Response..................................................................16

No Delay...................................................................................48

Number of Reports in Armed Period ........................... 23, 61, 62

Open Report Code ........................................................ 21, 61, 62

Operator Commands................................................................50

Optima 24 Plus FAX96 Modem................................................45

Other Features...........................................................................4

Other Functions .......................................................................48

Factory Defaults ...................................................................... 14

Fault......................................................................................... 52

FC....................................................................................... 52, 54

FCC Statement........................................................................ 59

Features..................................................................................... 4

Fire Sounder Timeout...................................................17, 61, 62

First Test Report Offset................................................20, 61, 62

Flexible Callback ....................................................23, 45, 61, 62

“Follow Me” Alarm Announcement......................................... 51

“Follow Me” Reminder Feature............................................... 51

Follow Me Reminder” Phone Number..................................... 19

Forced Bypass.........................................................17, 49, 61, 62

PABX Access Code ....................................................... 18, 61, 62

Pager.........................................................................................19

Pager Characters.......................................................... 22, 61, 62

Pager Function.........................................................................48

Pager Message..........................................................................22

Pager Report Format ...............................................................19

Paging Feature.........................................................................22

Panic Keys................................................................................47

PC.............................................................................................52

Perimeter Burglary..................................................................15

Periodic Test Report..................................................... 20, 61, 62

PH.............................................................................................52

Phone Lines................................................................................6

Phone System Select .................................................... 19, 61, 62

Piezo .........................................................................................60

Play Back a Message................................................................48

Plug-In Transformer ..................................................................9

Power Failure...........................................................................52

Power Up in Previous State......................................... 18, 61, 62

Powerline Carrier Device........................6, 17, 31, 32, 51, 61, 62

Powerline Carrier Device House Code...............................61, 62

Powerline Carrier Device Programming..................................33

Primary Phone Number............................................... 18, 61, 62

Primary Subscriber Account Number.......................... 18, 61, 62

Program Mode, Entering..........................................................14

Programming Mode..................................................................17

General Information................................................................ 11

General Programming Information......................................... 14

Go/No Go Test Mode................................................................ 12

Handshake Frequency............................................................. 54

Hardwire Zone................................................................6, 28, 63

Hayes ....................................................................................... 45

House ID.......................................................................13, 17, 32

House Identification ................................................................ 11

Input Type ....................................................................11, 28, 63

Installer Code .........................................................17, 47, 61, 62

Interactive Mode...................................................................... 14

Interior W/Delay...................................................................... 16

Interior, Follower..................................................................... 15

Keypad Backlight Timeout...........................................17, 61, 62

Keypad Functions.............................................................. 48, 49

Keys ......................................................................................... 11

Kissoff Frequency.................................................................... 54

Quick Arm ................................................................................48

Quick Arm Enable........................................................ 17, 61, 62

Quick Exit.................................................................................18

Radionics ..................................................................................19

Radionics/SESCOA ..................................................................60

Range........................................................................................11

Real-Time Clock Display.............................................. 17, 61, 62

Rechargeable Backup Battery ...................................................9

Record a Message.....................................................................48

Remote Phone Access...............................................................23

Remote Phone Control .............................................................49

Lack Of Usage Notification ..................................................... 20

Local Sounder Disable Jumper ................................................. 6

Long Range Radio...................................................................... 6

Long Range Radio/Alarm Audio Verification Trigger/Remote

Phone Control...................................................................... 23

Loop Number ..................................................................... 28, 63

LOW BAT................................................................................. 52

Low Battery Report Code .................................................. 61, 62

– 66 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote Programming.............................................................. 45

Remote Programming/Control........................................... 45, 46

Replacing the Rechargeable Battery....................................... 10

Report Code........................................................................ 20, 28

Report Code Formats............................................................... 54

Report Format.............................................................. 19, 61, 62

Restart Exit Delay ............................................................. 18, 48

RF............................................................................................. 28

RF (Supervised RF).................................................................. 11

RF House ID Code ....................................................... 17, 61, 62

RF Transmitter Low Battery Report Code.................. 21, 61, 62

RF Transmitter Low Battery Restore ......................... 22, 61, 62

RF Jam..................................................................................... 20

Ring Detect Count for Downloading............................ 23, 61, 62

Technical Support.................................................................... 58

Telco Handoff........................................................................... 45

Temporal Pulse........................................................................ 17

Test Mode ...............................................................48, 53, 56, 57

Test Report Code ..........................................................21, 61, 62

Test Restore Report Code.................................................. 61, 62

Testing The System................................................................. 53

Time and Date......................................................................... 48

Transmitter Loop Numbers .................................................... 13

Transmitter Supervision......................................................... 11

Transmitters............................................................................ 11

Trouble By Day/....................................................................... 15

Trouble Conditions.................................................................. 52

Trouble Report Code.....................................................21, 61, 62

Trouble Restore Report Code .......................................21, 61, 62

Troubleshooting Guide............................................................ 56

Two-Way Voice .......................................................................... 6

Scheduling.......................................................................... 46, 48

Secondary Phone Number ........................................... 18, 61, 62

Secondary Subscriber Account Number...................... 18, 61, 62

Secondary User Codes ............................................................. 47

Security Code Handshake ....................................................... 45

Security Codes ................................................................... 17, 47

Security Functions................................................................... 48

Serial Number.............................................24, 27, 29, 30, 35, 37

Sescoa/Rad ............................................................................... 54

Sescoa/Radionics Select ............................................... 20, 61, 62

Setting DIP Switches............................................................... 13

SH10A...................................................................................... 33

Signal Strength........................................................................ 12

Silent Burglary ........................................................................ 16

Single Alarm Sounding Per Zone ................................ 17, 61, 62

Siren/Horn................................................................................ 33

Site-Initiated Remote Programming....................................... 45

SMARTMODEM 1200 ............................................................. 45

Smoke Detectors ...................................................................... 57

Sniffer Mode................................................................. 12, 53, 56

Sounders .................................................................................... 6

Speaker Phone Operation........................................................ 49

Special Features ........................................................................ 4

Specifications ........................................................................... 60

Split/Dual Reporting.................................................... 19, 61, 62

Start By Event......................................................................... 31

Start By Zone Type.................................................................. 31

Start Event Type...................................................................... 33

Start Zone List......................................................................... 33

Start Zone Type ....................................................................... 33

Station-Initiated Remote Programming.................................. 45

STAY Mode ..............................................................................48

Stop Recording.........................................................................48

Stop Zone List..........................................................................33

Stop Zone Type.........................................................................33

Supervised Fire........................................................................16

Supervised RF.................................................................... 11, 28

System Battery ........................................................................56

System Communication..................................................... 54, 55

System Features ........................................................................4

System Operation ..................... 31, 32, 47, 48, 49, 50, 51, 52, 64

System Power.............................................................................4

System Words ..........................................................................39

Unsupervised Button RF......................................................... 11

Unsupervised RF..................................................................... 11

UR (Unsupervised RF) ...................................................... 11, 28

User Codes........................................................................... 4, 48

Voice Descriptor............................................................28, 30, 38

Voice Prompt Programming Mode .......................................... 14

Voice Vocabulary Index........................................................... 39

Voltage Input........................................................................... 60

Volume Control........................................................................ 48

Wall Mounting........................................................................... 5

WAVE2EX ............................................................................... 60

Wireless Buttons ..................................................................... 11

Wireless Dialer.............................................................19, 25, 26

Wireless Transmitter .............................................................. 21

Wiring Connections................................. 6

World Wide Web Address...................... 58

X-10...............................................................................31, 46, 51

Zone 1 Resistance.................................................................... 60

Zone Bypass............................................................................. 48

Zone Descriptor ....................................................................... 63

Zone Entry To List .................................................................. 34

Zone List.......................................................................24, 62, 64

Zone List Number.................................................................... 34

Zone List Programming........................................................... 34

Zone Lists For Devices ............................................................ 61

Zone Number..........................................................26, 28, 35, 38

Zone Programming............................................................ 61, 62

Zone Response Type .......................................................... 15, 16

Zone Type .......................................................................... 28, 33

Zones and Devices ..................................................................... 4

– 67 –

Download from Www.Somanuals.com. All Manuals Search And Download.

-Notes-

– 68 –

Download from Www.Somanuals.com. All Manuals Search And Download.

WARNING

THE LIMITATIONS OF THIS ALARM SYSTEM

While this System is an advanced design security system, it does not offer guaranteed protection against burglary, fire or

other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a

variety of reasons. For example:

•

Intrusion detectors (e.g., passive infrared detectors), smoke detectors, and many other sensing devices will not work

without power. Battery-operated devices will not work without batteries, with dead batteries, or if the batteries are not put

in properly. Devices powered solely by AC will not work if their AC power supply is cut off for any reason, however briefly.

•

Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even if the

signal path has been recently checked during a weekly test, blockage can occur if a metal object is moved into the path.

•

A user may not be able to reach a panic or emergency button quickly enough.

While smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not

activate or provide early warning for a variety of reasons in as many as 35% of all fires, according to data published by the

Federal Emergency Management Agency. Some of the reasons smoke detectors used in conjunction with this System may

not work are as follows. Smoke detectors may have been improperly installed and positioned. Smoke detectors may not

sense fires that start where smoke cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the other side of

closed doors. Smoke detectors also may not sense a fire on another level of a residence or building. A second floor detector,

for example, may not sense a first floor or basement fire. Finally, smoke detectors have sensing limitations. No smoke

detector can sense every kind of fire every time. In general, detectors may not always warn about fires caused by

carelessness and safety hazards like smoking in bed, violent explosions, escaping gas, improper storage of flammable

materials, overloaded electrical circuits, children playing with matches, or arson. Depending on the nature of the fire

and/or location of the smoke detectors, the detector, even if it operates as anticipated, may not provide sufficient warning to

allow all occupants to escape in time to prevent injury or death.

•

Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their

installation manual. Passive Infrared Detectors do not provide volumetric area protection. They do create multiple beams

of protection, and intrusion can only be detected in unobstructed areas covered by those beams. They cannot detect motion

or intrusion that takes place behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or windows.

Mechanical tampering, masking, painting or spraying of any material on the mirrors, windows or any part of the optical

system can reduce their detection ability. Passive Infrared Detectors sense changes in temperature; however, as the

ambient temperature of the protected area approaches the temperature range of 90° to 105°F (32° to 40°C), the detection

performance can decrease.

Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if they are located on the

other side of closed or partly open doors. If warning devices are located on a different level of the residence from the

bedrooms, then they are less likely to waken or alert people inside the bedrooms. Even persons who are awake may not

hear the warning if the alarm is muffled by noise from a stereo, radio, air conditioner or other appliance, or by passing

traffic. Finally, alarm warning devices, however loud, may not warn hearing-impaired people.

•

Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service or

temporarily out of service. Telephone lines are also subject to compromise by sophisticated intruders.

Even if the system responds to the emergency as intended, however, occupants may have insufficient time to protect

themselves from the emergency situation. In the case of a monitored alarm system, authorities may not respond

appropriately.

•

This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to

last as long as 20 years, the electronic components could fail at any time.

The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This

alarm system should be tested weekly to make sure all sensors and transmitters are working properly. The security keypad

(and remote keypad) should be tested as well.

Wireless transmitters (used in some systems) are designed to provide long battery life under normal operating conditions.

Longevity of batteries may be as much as 4 to 7 years, depending on the environment, usage, and the specific wireless device

being used. External factors such as humidity, high or low temperatures, as well as large swings in temperature, may all reduce

the actual battery life in a given installation. This wireless system, however, can identify a true low battery situation, thus

allowing time to arrange a change of battery to maintain protection for that given point within the system.

Installing an alarm system may make the owner eligible for a lower insurance rate, but an alarm system is not a substitute for

insurance. Homeowners, property owners and renters should continue to act prudently in protecting themselves and continue to

insure their lives and property.

We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved ones

to learn about these developments.

– 69 –

Download from Www.Somanuals.com. All Manuals Search And Download.

LIMITED WARRANTY

Honeywell International Inc. acting through its Security & Custom Electronics business ("Seller"), 165

Eileen Way, Syosset, New York 11791, warrants its products to be in conformance with its own plans and

specifications and to be free from defects in materials and workmanship under normal use and service for 24

months from the date stamp control on the product or, for products not having an Ademco date stamp, for 12

months from date of original purchase unless the installation instructions or catalog sets forth a shorter

period, in which case the shorter period shall apply. Seller's obligation shall be limited to repairing or

replacing, at its option, free of charge for materials or labor, any product, which is proved not in compliance

with Seller's specifications or proves defective in materials or workmanship under normal use and service.

Seller shall have no obligation under this Limited Warranty or otherwise if the product is altered or

improperly repaired or serviced by anyone other than Honeywell factory service. For warranty service,

return product transportation prepaid, to Honeywell Factory Service, 165 Eileen Way, Syosset, New York

11791.

THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FITNESS FOR

A PARTICULAR PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE

FACE HEREOF. IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL

OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR

IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR

DAMAGE IS CAUSED BY THE SELLER'S OWN NEGLIGENCE OR FAULT.

Seller does not represent that the products it sells may not be compromised or circumvented; that the

products will prevent any personal injury or property loss by burglary, robbery, fire or otherwise; or that the

products will in all cases provide adequate warning or protection. Customer understands that a properly

installed and maintained alarm may only reduce the risk of a burglary, robbery, fire or other events

occurring without providing an alarm, but it is not insurance or a guarantee that such will not occur or that

there will be no personal injury or property loss as a result. CONSEQUENTLY, SELLER SHALL HAVE NO

LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED ON A

CLAIM THE PRODUCT FAILED TO GIVE WARNING. HOWEVER, IF SELLER IS HELD LIABLE,

WHETHER DIRECTLY OR INDIRECTLY, FOR ANY LOSS OR DAMAGE ARISING UNDER THIS

LIMITED WARRANTY OR OTHERWISE, REGARDLESS OF CAUSE OR ORIGIN, SELLER'S MAXIMUM

LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT, WHICH

SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER. This warranty replaces

any previous warranties and is the only warranty made by Seller on this product. No increase or alteration,

written or verbal, of the obligations of this Limited Warranty is authorized.

– 70 –

Download from Www.Somanuals.com. All Manuals Search And Download.

C A R R I E R D E V I C E S

W E P R O L I N E

T R I G G E R S I G N A L ( N E G )

NOTE: Connection of the fire alarm signal to a fire alarm headquarters or a central station shall be permitted with the

approval of the local authority having jurisdiction. The burglar alarm signal shall not be connected to a police

emergency number.

The System must be checked by a qualified technician once every three years.

– 71 –

Download from Www.Somanuals.com. All Manuals Search And Download.

165 Eileen Way, Syosset, New York 11791

‡K5963V3oŠ

www.honeywell.com/security

K5963V3bx 5/04 Rev. A

Download from Www.Somanuals.com. All Manuals Search And Download.

Graham Field Personal Lift LF2020 User Manual
Greenheck Fan Nail Gun QEI User Manual
Grizzly Cordless Sander G0529 User Manual
Hamilton Beach Blender 908 Series User Manual
Hamilton Beach Coffeemaker 47535C User Manual
Harbor Freight Tools Saw 03733 User Manual
Hawking Technology Digital Camera HNC300 User Manual
Hotpoint Oven BS43 User Manual
HP Hewlett Packard Portable Generator HP 8644A User Manual
HP Hewlett Packard Projector mp3130 Series User Manual