Honeywell Clock TE211W User Manual

Atomic Clock  
with Wireless  
Indoor/Outdoor  
Thermometer  
USER MANUAL  
(TE211W)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
A PRECISE TIME WITH TEMPERATURE IN  
THREE-LINE LCD DISPLAY  
View of indoor/outdoor temperature and precise time.  
B ALARM BUTTON  
Sets an alarm and allows displaying alarm status.  
H
A
C CHANNEL BUTTON  
Recalls the different remote sensor reading.  
D MEMORY BUTTON  
CH  
1). Recalls maximum or minimum temperature.  
2). Clears the memory.  
PM  
E MODE BUTTON  
Changes display modes and confirms settings.  
M
D
F UP ( ) BUTTON  
1). Increases the setting.  
2). Enables atomic clock reception.  
3). Activates Time Zone settings.  
4.) Activates alarm.  
F
E
C
G
B
D
G DOWN ( ) BUTTON  
1).Decreases the setting.  
2). Activates the remote sensors search.  
3). Disables the alarm.  
H
SNOOZE/LIGHT BUTTON  
1). Activates snooze function and LCD backlight.  
2). Stops alarm temporarily.  
3
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
F °C/ °F SWITCH  
REMOTE SENSOR  
FEATURES  
Selects the temperature display unit in Celsius or Fahrenheit.  
Remote temperature transmission to the main unit via  
433 MHz signal  
BEFORE YOU BEGIN  
1. We recommend using alkaline batteries for the main unit  
and remote sensor.  
Case can be wall mounted using built-in hanger  
100 feet transmission range without interference  
Temperature display selection in Fahrenheit or Celsius  
Transmission channel selection  
2. Avoid using rechargeable batteries.  
3. Insert batteries before first use, matching the polarity as  
shown in the battery compartment.  
4. Always install batteries in the remote sensor before the  
main unit.  
5. Press RESET after each battery change, using a paper clip  
or similar tool.  
E
6. During an initial setup, place the main unit as close as  
possible to the remote sensor.  
MADE IN CHINA  
A
F
D
7. After reception is established (remote temperature will  
appear on the receiver’s display), position the remote sensor  
and main unit within the effective transmission range of  
100 feet.  
C
B
NOTE:  
TM  
1. Avoid setting the time and date on the main unit before the  
outdoor temperature is displayed.  
THERMO  
SENSOR  
2. The effective operating range may be influenced by the  
surrounding building materials and how the receiver and  
transmitter are positioned.  
3. Position the remote sensor so that it faces the main unit  
(receiver), minimizing obstructions such as doors, walls,  
and furniture.  
A LED INDICATOR  
Flashes once when the remote sensor transmits the  
reading to the main unit.  
4. Though the remote sensor is weather-resistant, it should  
be placed away from direct sunlight, rain or snow.  
Flashes twice indicating low battery.  
B BATTERY COMPARTMENT  
BATTERY INSTALLATION  
Holds two AA-size batteries.  
REMOTE SENSOR  
NOTE: Install the batteries; select the channel and type of  
temperature (ºC/ºF) before you mount the sensor.  
1. Remove the screws from the battery compartment with a  
small Phillips screwdriver.  
C RESET  
Resets all previous settings.  
D CHANNEL SWITCH  
2. Set the channel. The switch is located in the battery  
compartment. Channel 1 is typically selected if  
only one remote sensor is being used.  
Selects the desired channel.  
E WALL-MOUNT RECESSED HOLE  
3. If you are using more than one sensor, select a different  
channel for each sensor.  
Keeps the remote sensor on the wall.  
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Install two “AA” size alkaline batteries (not included)  
matching to the polarities shown in the battery compartment.  
5. Replace the battery compartment door and secure the screws.  
6. Secure the remote sensor in the desired location.  
The unit is in searching mode.  
Temperature readings are  
securely registered.  
BATTERY INSTALLATION:  
MAIN UNIT  
˚F  
No signals.  
1. Open the battery compartment door.  
2. Install two batteries (UM-3 or “AA” size 1.5V) matching  
the polarity as shown in the battery compartment.  
3. Replace the battery compartment door.  
WWVB RADIO CONTROLLED TIME  
The NIST (National Institute of Standards and Technology)  
radio station is located in Ft. Collins Colorado. It transmits  
an exact time signal continuously throughout the continental  
United States at 60 KHz frequency. The Atomic Clock  
can receive this WWVB signal through its internal antenna  
from up to 2,000 miles away. Due to the nature of the Earth’s  
ionosphere, reception can be limited during the daylight hours.  
The radio controlled clock will search for an alternate station  
that receives its signal from the NIST Atomic clock in Boulder,  
Colorado.  
LOW BATTERY WARNING  
A low-battery indicator [  
] will appear on the indoor or  
remote temperature reading line of the main unit warning that  
the corresponding batteries need replacement..  
GETTING STARTED  
After batteries are installed, remote sensors will transmit  
temperature readings at 45 second intervals. The main unit  
may take up to 2 (two) minutes to receive the initial readings.  
Upon successful reception, remote temperature will be  
displayed. Then the main unit will automatically update  
readings at 45-second intervals.  
The WWVB tower icon on the main unit’s display will flash  
indicating radio signal reception from the WWVB station.  
If the tower icon is not fully lit, or if the time is not set  
automatically, please consider the following:  
If no signals are received from the remote sensor(s) within  
(2) two minutes, dashes “  
” will be displayed.  
*
During night-time hours, atmospheric disturbances are  
typically less severe and reception may improve.  
A single daily reception is sufficient enough to keep  
the accuracy reading within 1 second.  
Press and hold [ ] button on the main unit for 2 seconds  
to initiate another signal search.  
CHECKING REMOTE AND INDOOR TEMPERATURES  
The wave icon on the main unit's display located near the  
remote sensor reading line, indicates a good reception from  
the remote sensor. If the temperature goes above or below the  
temperature operating range stated in specifications, the  
*
Make sure the main unit is positioned at 8 feet minimum  
distance from any interference source such as a TV,  
computer monitor, microwave, etc. The successful reception  
of the atomic time signal depends on the positioning and  
location of the clock. Always place the main unit by the  
window for better reception.  
display will show dashes “  
”.  
READING THE KINETIC WAVE DISPLAY  
The kinetic wave display shows the main unit (receiver)  
signal reception strength.  
*
Within concrete wall rooms such as basements or office  
buildings, the received signal may be weakened.  
Always place the unit near the window.  
7
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAXIMUM AND MINIMUM TEMPERATURE  
The maximum and minimum record of the indoor and remote  
temperature will be automatically stored in the memory of the  
main unit (receiver). Main unit will display the minimum,  
maximum and the current reading upon each press of  
MEMORY button. The unit will return to the current  
temperature display in 15 seconds. To clear the memory,  
press and hold "MEM" for 3 seconds and all stored readings  
will be erased.  
If everything listed above is in order and there is no reception  
anyway, please perform the following steps:  
1. Bring main unit and remote sensor close together.  
2. Remove 4 small screws from the back of the remote sensor  
and open the battery compartment.  
3. Remove the batteries from the battery compartment and  
reinstall them in the same manner. Remote sensor  
LED indicator will flash showing transmission of the signal.  
4. Remove the batteries from the main unit and reinstall  
them in the same manner.  
5. On the main unit select the same channel number as  
set on the remote sensor. Outdoor temperature  
on the display will show that transmission is being  
received successfully .  
TEMPERATURE TRENDS  
The remote temperature trend indicator shows the trend of  
temperatures collected at particular remote sight. There are  
three trends will be shown: rising, steady, and falling.  
TRANSMISSION COLLISION  
TREND  
TREND  
TREND  
Arrow  
Signals from other household devices, such as doorbells,  
home security systems, and entry controls, may interfere  
with this product and may cause temporary reception  
failure. This is normal and will not affect the general  
performance of the product. The transmission and reception  
of temperature readings will resume once the interference  
subsides.  
indicator  
Temperature  
Trend  
Rising  
Steady  
Falling  
ATOMIC CLOCK  
LOST COMMUNICATIONS  
1. After the main unit receives temperature readings from the  
remote sensor(s), the WWVB time signal receiver will  
automatically search for the time signal. This takes  
about 5-8 minutes.  
If the main unit display for the remote sensor goes blank,  
press and hold [ ] button for 2 seconds to begin a new signal  
search. If the signal still isn’t received, please make sure that:  
1. The remote sensor is in its proper location.  
2. The distance between main and remote units is not  
over 100 feet.  
2. If the radio signal is received, the date and time will be  
set automatically, and the [ ] icon will appear.  
3. If in 8 minutes the time signal has not been received,  
press “MODE” button to set the time manually. Always  
place the main unit by the window for better reception.  
4. The clock will continue to search for the WWVB time  
signal daily for every hour between 1:00 am and 4:30 am.  
After the signal has been successfully received, the time  
and date will be updated automatically.  
3. The path between the units is clear of obstacles. Shorten the  
distance between units if necessary.  
4. Fresh batteries are installed correctly in both remote and  
main units.  
Note: When the temperature falls below freezing, the batteries  
in outdoor remote sensors may have reduced voltage supply  
and a shorter effective range. We recommend to  
Use lithium-ion batteries at the temperatures below 32°F  
CALENDAR AND CLOCK DISPLAY MODES  
Date is displayed in month-date format. Each press of the  
MODE button will change the clock display setting between  
the time with seconds and time with weekday.  
10  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
SETTING CLOCK MANUALLY  
TIME ZONE  
ALARMS  
* Weekday Alarm  
1. Press MODE to select the time display with weekday.  
The alarm will sound and the alarm icon will flash at the  
set time Mondays through Fridays.  
2. Select the time zone by pressing and holding the “  
button for 3 seconds.  
3. Keep holding until the desired time zone (Pacific,  
* Single Day Alarm  
Mountain, Central or Eastern) is selected on the display map.  
The alarm will sound and the alarm icon will flash at the  
set time, but will not activate on subsequent days.  
YEAR, DATE, TIME, TEMPERATURE UNIT  
Press and hold MODE for 3 seconds: the year will flash.  
* Pre-Alarm  
Press “  
” or “  
” to change the flashing digits.  
If an outdoor temperature is 32º F / 0º C or below, the  
pre-alarm feature will be activated. The pre-alarm time  
interval can be set for 15, 30, 45, 60 or 90 minutes  
before the weekday or single alarm time. Press and hold  
[ALARM] button for two seconds in Pre-Alarm mode  
to set the pre-alarm interval.  
After the first value is set, press MODE again.  
Continue setting month, day,12 or 24 time format hour,  
minutes, language of weekday, and Fahrenheit or Celsius  
display. When you’ve set the last value, press MODE for  
the last time to return to regular mode.  
W” (Weekday alarm), “ S” (Single day alarm), and  
SETTING THE ALARM  
“Pre-AL” (Pre-alarm) icons will indicate which alarm mode  
is armed. You can enable or disable an alarm by pressing the  
To set any alarm,  
1. Press [ALARM] once to display alarm time.  
If the alarm is off, “OFF” will be displayed.  
2. Press and hold [ALARM] for two seconds.  
The hour digit will flash.  
[
], [ ] buttons in alarm display mode. Press MODE to  
toggle between alarm modes or to return to the default display.  
3. Enter the hour using [  
] or [  
].  
PRECAUTIONS  
4. Press [ALARM] again. The minute digits will flash.  
This product is engineered to give you years of satisfactory  
service if handled carefully. Here are a few precautions:  
1. Do not immerse the units in water.  
5. Enter the minutes using [ ] or [  
].  
6. Press [ALARM] again to exit.  
7. Repeat the same procedure to set the next alarm.  
2. Do not clean the units with abrasive or corrosive materials.  
They may scratch the plastic parts and corrode the  
electronic circuits.  
SNOOZE  
3. Do not subject the product to excessive force, shock, dust,  
temperature, or humidity, which may result in malfunctions,  
shorter lifespan, damaged batteries, and damaged parts.  
4. Do not tamper with the units' internal components. Doing  
so will invalidate the warranty and may cause damage.  
These units contain no user-serviceable parts.  
When the alarm sounds, press the SNOOZE/LIGHT button  
to temporarily stop the alarm. After depressing  
SNOOZE/LIGHT button, the alarm sound will resume in  
5 minutes. If the alarm is not disabled after that, it will sound  
for 4 more minutes and then will stop by itself.  
5. Use only fresh batteries. Do not mix new and old batteries.  
6. Read the user's manual thoroughly before operating the units.  
DISABLING ALARM  
Press [ALARM] button on the main unit to disable an alarm.  
11  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIFICATIONS  
Temperature Measurement  
Main unit  
FCC STATEMENT  
This device complies with Part 15 of the FCC Rules.  
Operation is subject to the following two conditions:  
(1) This device may not cause harmful interference, and  
(2) This device must accept any interference received,  
including interference that may cause undesired operation.  
Indoor Temperature  
Proposed operating range  
: -5.0°C to +50.0°C /  
23.0°F to 158.0°F  
: 0.1°C/ 0.2°F  
Temperature resolution  
Warning: Changes or modification to this unit not expressly  
approved by the party responsible for compliance could void  
the user’s authority to operate the equipment.  
Remote Sensor  
Proposed operating range  
with alkaline batteries  
: -20°C to + 70°C /  
-4°F to 158°F  
NOTE: This equipment had been tested and found to comply  
with the limits for a Class B Digital device, pursuant to  
Part 15 of the FCC Rules. These limits are designed to  
provide reasonable protection against harmful interference  
in a residential installation. This equipment generates, uses  
and can radiate radio frequency energy and, if not installed and  
used in accordance with the instructions, may cause harmful  
interference to radio communications.  
Proposed operating range  
with lithium batteries  
: - 38°F to 158°F  
( -38.8 C° to 70°C)  
: 0.1°C/ 0.2°F  
Temperature resolution  
RF Transmission Frequency  
: 433 MHz  
Maximum number of Remote sensors : 3  
RF Transmission Range  
: Maximum 100 feet  
Temperature sampling cycle  
: approximately  
45 seconds  
However, there is no guarantee that interference will not  
occur in a particular installation. If this equipment does cause  
harmful interference to radio or television reception, which  
can be determined by turning the equipment off and on, the  
user is encouraged to try to correct the interference by one  
or more of the following measures:  
Calendar and Clock  
12/24 hour display in hh : mm format  
Date Format: Month – Day format  
Day of week: User- selectable in 5 languages  
(English, Spanish, French, German, Italian)  
1. Reorient or relocate the receiving antenna.  
2. Increase the separation between the equipment and receiver.  
3. Connect the equipment to an outlet on a circuit different  
from that to which the receiver is connected.  
4. Consult the dealer or an experienced radio / TV  
technician for help.  
Dual 4-minute crescendo alarm with snooze  
Pre-alarm for ice alert with programmable intervals of  
15, 30, 45, 60 and 90 minutes  
Blue Backlight  
Power  
Main unit: 2 AA batteries (not included)  
Remote Sensor: 2 AA batteries (not included)  
Dimensions  
Main unit: 3.54(L) x 4.92(H) x 1.89(D) inches  
Remote sensor: 2.38(L) x 4(H) x 1 (D) inch  
13  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DECLARATION OF CONFORMITY  
STANDARD WARRANTY INFORMATION  
This product is warranted from the manufacturing defects for  
one year from date of retail purchase. It does not cover  
damages or wear resulting from accident, misuse, abuse,  
commercial use, or unauthorized adjustment and repair.  
We  
Name: Hideki Electronics, Inc.  
Address: 7865 SW Mohawk, Tualatin, OR 97062  
Telephone No.: 1-503-612-8395  
Note that online product registration is required to ensure  
valid warranty protection.  
declare that the product  
To register your product, go to our Company website at:  
under the Customer Service menu.  
Product No.: TE211W  
Product Name: Atomic Clock with Wireless  
Indoor/ Outdoor Thermometer  
Should you require assistance with this product and its  
operation, please contact our  
Manufacturer: Hideki Electronics Ltd.  
Address: Unit 2304-06, 23/F Riley House, 88 Lei Muk Road,  
Kwai Chung, New Territories, Hong Kong  
Customer Service Hotline 1(866) 443 3543  
Please direct all returns to the place of the original purchase.  
Should this not be possible, contact Customer Service Hotline  
for assistance and to obtain a Return Merchandise Authorization  
(RMA). Returns without a return authorization will be refused.  
Please retain your original receipt as you may be asked to  
provide a copy for proof of purchase.  
is in conformity with Part 15 of the FCC Rules. Operation is  
subject to the following two conditions:  
1. This device may not cause harmful interference.  
This device must accept any interference received, including  
interference that may cause undesired operation.  
Hideki Electronics, Inc. reserves the right to repair or replace  
the product at our option.  
The information above is not to be used as contact for support  
or sales. Please call our customer service hotline  
Copyright (2005) Hideki Electronics Inc. All Rights Reserved.  
The Honeywell Trademark is used under license from  
Honeywell Intellectual Properties Inc.  
(refer to the warranty statement) for all inquiries instead.  
Honeywell International Inc. makes no representations or  
warranties with respect to this product.  
15  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Graco Baby Swing 1424 User Manual
Graco Inc Power Roller 243066 User Manual
Graco Stroller PD213968A User Manual
Graham Field SONAR 14423 2 User Manual
Greenway Home Products Water Dispenser VWD8956BLS User Manual
Halo Lighting System Indoor Furnishings H2TMPSML User Manual
Husqvarna Automobile HUV4421D User Manual
Husqvarna Chainsaw 317 EL 321 EL User Manual
Husqvarna Cordless Saw FS 700 EX User Manual
i Tech Dynamic Headphones iCube User Manual