TABLE OF CONTENTS
INTRODUCTION
3
ABOUT HIDEKI ELECTRONICS
PRODUCT OVERVIEW
REMOTE SENSOR
3
4
7
BEFORE YOU BEGIN
9
BATTERY INSTALLATION
LOW BATTERY WARNING
TABLE STAND
10
11
11
11
Wireless Thermometer
with
GETTING STARTED
CHECKING REMOTE AND INDOOR
TEMPERATURES
12
12
13
Alarm Clock
MAXIMUM AND MINIMUM READINGS
LOST COMMUNICATION
CALENDAR AND CLOCK DISPLAY MODES 13
MANUAL SETTINGS
SNOOZE
14
15
15
16
17
18
19
20
DISABLING ALARM
PRECAUTIONS
SPECIFICATIONS
FCC STATEMENT
DECLARATION OF CONFORMITY
STANDARD WARRANTY INFORMATION
( TE103NL )
USER MANUAL
2
HONEYWELL TE103NL & TS03C MANUAL (ENG)
SIZE: W65 X H105 (mm)
BY WING TSUI 31/03/08
INTRODUCTION
PRODUCT OVERVIEW
MAIN UNIT
Thank you for selecting the Wireless Thermometer
with Alarm Clock. This device includes precise time
keeping with temperature monitoring features that you
can use from the comfort of your home.
In this package you will find:
FEATURES
• Wireless transmission of the temperature from the
remote sensor to the main unit from up to 100 feet
(30 meters) away
• One main unit (receiver)
• Remote temperature display
• One remote sensor (transmitter) TS03
Please keep this manual handy as you use your new
item. It contains practical step-by-step instructions, as
well as technical specifications and precautions you
should know.
• Indoor temperature display
• Quartz clock
• Calendar displaying date with month and day of the
week in English, Spanish, French, German or Italian
• Dual crescendo alarm with snooze feature
• Programmable Freeze Pre-Alarm
• Wall mount or desktop option
• Low battery indicator
3
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
NOTE: Batteries in the outdoor remote sensors may
have reduced voltage supply and a shorter effective
range at temperatures below freezing. We
recommend using lithium batteries below 32°F
(0°C).
• The remote sensor can be placed indoors or
outdoors, the main unit must be placed indoors.
• We recommend using alkaline batteries for the
remote sensor and main unit when temperatures are
above 32°F (0°C). We recommend using AA lithium
batteries for the remote sensor when temperatures
are below 32°F (0°C).
BATTERY INSTALLATION
REMOTE SENSOR
• Avoid using rechargeable batteries. (Rechargeable
batteries cannot maintain correct power requirements).
• Insert batteries before first use, matching the polarity
in the battery compartment.
NOTE: Install the batteries; select the channel and
temperature in C° or F° before mounting the remote
sensor.
• Remove the screws from the battery compartment
with a small Phillips screwdriver.
• Select the desired channel. The switch is located in
the battery compartment. Channel 1 is the default
setting and typically selected if only one remote
sensor is being used.
• Install 2 “AA” size alkaline batteries (not included)
matching the polarities shown in the battery
compartment.
• Replace the battery compartment door and secure the
screws.
• Secure remote sensor in the desired location.
• ALWAYS install batteries in the remote sensor
before the main unit.
• Press RESET after each battery change with a paper
clip or similar tool.
• During an initial setup, place the main unit as close
as possible to the remote sensor.
• After reception is established (the remote temperature
will appear on the main unit’s display), position the
remote sensor and the main unit within the effective
transmission range of 100 feet (30 meters).
NOTE:
1. Avoid setting manually the time and date on the main
unit before the remote temperature is displayed.
2. The effective operating range may be influenced by
the surrounding building materials and how the receiver
and transmitter are positioned.
MAIN UNIT
• Open the battery compartment door.
• Install 2 batteries (UM-3 or “AA” size 1.5V) matching
the polarity as shown in the battery compartment.
• Replace the battery compartment door.
3. Place the remote sensor so that it faces the main unit
(receiver), minimizing obstructions such as doors,
walls, and furniture.
4. Though the remote sensors are weather-resistant,
they should be placed away from direct sunlight, rain
or snow.
9
10
LOW BATTERY WARNING
CHECKING REMOTE AND INDOOR
TEMPERATURES
A low-battery indicator [ ] will appear on the indoor
or remote temperature reading line of the main unit
warning that the corresponding batteries need
replacement.
The remote temperature information line is located on
the top of the main unit’s display.
The wave icon is located above the remote channel
number and indicates the reception status from the
remote sensor.
TABLE STAND
The main unit has a removable table stand that supports
it on the flat surface. Attach table stand to the bottom of
the main unit in the slots provided. The unit can also be
mounted on the wall using the recessed screw hole. The
table stand must be removed prior to mounting.
There are three remote status types:
The unit is in searching mode.
Temperature readings
securely registered.
No signals detected.
- - -
GETTING STARTED
After batteries are installed; the remote sensor will
transmit temperature readings at 45 second intervals.
The main unit may take up to two minutes to receive
the initial readings. Upon successful reception, remote
temperature will appear on the top line of the main
unit’s display. The main unit will automatically update
readings at 45-second intervals.
The indoor temperature with the icon IN is located
below the remote temperature information line.
NOTE: If the indoor or remote temperature goes above
or below operating range stated in specifications, the
main unit’s display will show dashes “- - -”
If no signals received from the remote sensor within
two minutes, dashes [- - -] will be displayed. Press and
hold DOWN ( ) button on the main unit for two
seconds to initiate another signal search.
MAXIMUM AND MINIMUM READINGS
The maximum and minimum record of the indoor and
remote temperatures will be automatically stored in the
memory of the main unit (receiver).
To display the minimum, maximum or the current
reading press MEMory button.
If no button is pressed for the next 15 seconds, the unit
will return to the current temperature display.
To clear the memory, press and hold MEMory button
for two seconds and all previously stored readings will
be erased.
11
12
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUAL SETTINGS
LOST COMMUNICATION
CLOCK
If the main unit display line for the remote sensor
reading goes blank, press and hold DOWN ( ) button
for 2 seconds to begin a new signal search. If the signal
still isn’t received, make sure that remote sensor is in
its proper location:
• Press and hold MODE button for 3 seconds: the year
digits will flash.
• Press UP ( ) or DOWN ( ) to change flashing digits.
• After the first value is set, press MODE button again
to confirm.
• The distance between main unit and remote sensor is
not over 100 feet (30meters).
• Continue setting month, date, time display format, 12
or 24 hour time format, hour, minute, day of the week
display language, time zone and Fahrenheit or Celsius
display.
• The path between units is clear of obstacles. Reduce
the distance as necessary.
• Fresh batteries are installed correctly in both units.
• Press MODE for the last time to return to the default
mode (time of day with seconds) after the last
parameter is set.
If there is no reception, please perform the following steps:
• Bring the main unit and remote sensor close together.
• Remove four (4) small screws from the back of the
remote sensor with small Phillips screwdriver, and
open the battery compartment.
ALARMS
(W) Weekly Alarm
The alarm will sound and the alarm icon will flash at
the set time Mondays through Fridays.
• Remove the batteries from the battery compartment
and reinstall them in the same manner. Remote
sensor LED indicator will flash showing transmission
of the signal.
(S) Single Day Alarm
The alarm will sound and the alarm icon will flash at
the set time, but will not activate on subsequent days.
(PRE-AL) Low Temperature Pre-Alarm for remote location
If the remote temperature reaches 32ºF (0ºC) or below,
the pre-alarm feature will be activated. The pre-alarm
time interval can be set for 15, 30, 45, 60 or 90 minutes
earlier than the day of the week or single alarm time.
Press and hold ALARM button for two seconds in Pre-
Alarm mode to set the pre-alarm interval.
• Remove the batteries from the main unit and reinstall
them in the same manner.
• The remote temperature appeared on the main unit’s
display will show that transmission is being received
successfully.
W (Weekly alarm), S (Single day alarm), and PRE-AL
(Pre-alarm) icons will indicate which alarm mode is
armed. You can enable or disable an alarm by pressing
the UP ( ) or DOWN ( ) buttons in the selected alarm
display mode. Press ALARM button to toggle between
CALENDAR AND CLOCK DISPLAY MODES
Date is displayed in month-date or date-month format.
Each press of the MODE button will change the clock
display setting between the time of day with seconds,
time of day with the day of the week and a calendar.
13
alarm modes or to return to the default display.
14
SETTING THE ALARM
PRECAUTIONS
To set any alarm,
This product is engineered to give you years of
satisfactory service if handled carefully. Here are a few
precautions:
• Press ALARM button once to display alarm time. If
the alarm is off, OFF will be displayed.
• Press and hold ALARM button for two seconds. The
hour digit will flash.
• Enter the hour using DOWN ( ) or UP ( ).
• Press ALARM button again. The minute digits will
flash.
• Enter the minutes using DOWN ( ) or UP ( ).
• Press ALARM button again to exit.
• Repeat the same procedure to set a Single and Pre-
Alarm.
• Do not immerse the units in water.
• Do not clean the units with abrasive or corrosive
materials. They may scratch the plastic parts and
corrode the electronic circuits.
• Do not subject the product to excessive force, shock,
dust, temperature, or humidity, which may result in
malfunctions, shorter lifespan, damaged batteries,
and damaged parts.
• Do not tamper with the units internal components.
Doing so will invalidate the warranty and may cause
damage. These units contain no user-serviceable parts.
• Use only fresh batteries. Do not mix new and old
batteries.
• Read the user's manual thoroughly before operating
the units.
SNOOZE
When the alarm sounds, press the SNOOZE button to
temporarily stop the alarm. After the SNOOZE is
depressed, the alarm sound will resume in five (5)
minutes. If the alarm is not disabled after that, it will
sound for four (4) more minutes and then will stop by
itself.
TRANSMISSION COLLISION
Signals from the other household devices such as
wireless doorbells, home security systems, and entry
control, may interfere with this product or cause
temporary reception interruption. This is normal and
will not affect the general performance of the product.
The transmission and reception of the temperature
readings will resume once the interference subsides.
DISABLING ALARM
Press ALARM button on the main unit to disable any
of the alarms. When Weekly, Daily or Pre-Alarm is
disabled, an applicable icon W, S, or Pre-Al will
disappear from the main unit’s display.
15
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
FCC STATEMENT
Main Unit
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired operation.
Warning: Changes or modification to this unit not
expressly approved by the party responsible for
compliance could void the user’s authority to operate
the equipment.
Indoor Temperature
Proposed operating range: -5.0°C to +50.0°C/23.0°F to 122.0°F
Temperature resolution: 0.1°C/0.2°F
User-selectable ( °F or °C ) temperature display
Low battery indicator
Calendar and Clock
12/24 hour display in hh: mm format
Date format: month-day or day-month format
Day of the week: User-selectable in five languages
(English, Spanish, French, German, Italian)
Time Zone manual adjustment
NOTE: This equipment had been tested and found to
comply with the limits for a Class B Digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment, installed and used in accordance with the
instructions, may cause harmful interference to radio
communications.
There is no guarantee that interference will not occur in
a particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to improve or correct
turning the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and
receiver.
• Connect the equipment to an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio / TV
technician for help.
Dual two-minute crescendo alarms with a four minutes snooze
Freeze pre-alarm with programmable time intervals
Wall Mount or Desktop option
Remote Sensor
Remote Temperature
Proposed operating range with alkaline batteries:
-20.0°C to + 70.0°C/-4.0°F to + 158°F
Proposed operating range with lithium batteries:
-38.8°C to + 70.0°C/-38.0°F to +158°F
Temperature resolution: 0.1°C/0.2°F
Low battery indicator
RF Transmission Frequency: 433 MHz
Maximum number of remote sensors: 1 (included)
RF transmission range: Maximum 100 feet (30 meters)
Temperature transmission cycle: approximately 45 seconds
Power
Main unit: 2 AA size (UM-3) 1.5V batteries (not
included)
Remote Sensor: 2 AA size (UM-3) 1.5V batteries (not
included)
Dimensions
Main unit: 2.64(L) x 4.84(H) x 1.02(D) inches
Remote sensor: 2.37(L) x 4(H) x 1(D) inch
17
18
DECLARATION OF CONFORMITY
We
STANDARD WARRANTY INFORMATION
This product is warranted from manufacturing defects
for one year from date of retail purchase. It does not
cover damages or wear resulting from accident, misuse,
abuse, commercial use, or unauthorized adjustment and
repair.
Name: Hideki Electronics, Inc.
Address: 7865 SW Mohawk, Tualatin, OR 97062
Telephone No.: 1-503-612-8395
declare that the product
Product No.: TE103NL
Note that online product registration is required to
ensure valid warranty protection.
Product Name: Wireless Thermometer with Alarm
Clock
To register your product, go to our Company website
Product Registration under the Customer Service menu.
Contact our Customer Service Hotline 1(866) 443-3543
for assistance with this product and its operation.
Please direct all returns to the place of the original
purchase. Should this not be possible, contact Hideki
Customer Service Hotline for assistance and to obtain a
Return Merchandise Authorization (RMA). Returns
without a return authorization will be refused. Retain
your original receipt as you may be asked to provide a
copy for proof of purchase.
Manufacturer: Hideki Electronics Ltd.
Address: Unit 2304-06, 23/F Riley House, 88 Lei Muk
Road, Kwai Chung, New Territories, Hong Kong
is in conformity with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received,
including interference that may cause undesired
operation.
The information above is not to be used as a contact
for support or sales. Please call our customer service
hotline (refer to the Standard Warranty
Hideki Electronics, Inc. reserves the right to repair or
replace the product at our option.
Information) for all injuries instead.
©2008 Hideki Electronics, Inc. All rights reserved.
Weathertime is a trademark of Hideki Electronics, Inc.
The Honeywell trademark is used under license from
Honeywell International Inc. Honeywell International
Inc. makes no representations or warranties with
respect to this product.
19
20
Download from Www.Somanuals.com. All Manuals Search And Download.
|