UNVENTED ROOM HEATER
DiamondGlo Heater
Models HMDGII and HMDGJ
WARNING: Improper installation, adjustment, alteration, service or
maintenance can cause property damage, personal injury or loss of life. Refer to
this manual for information. Installation and service must be performed by a
qualified installer, service agency or the gas supplier.
This is an unvented gas-fired heater. It uses air (oxygen) from the
room in which it is installed. Provisions for adequate combustion
and ventilation air must be provided. Refer to page 4 of these
instructions.
This heater is equipped with a PILOT LIGHT SAFETY SYSTEM designed to turn off the heater if not
enough fresh air is available.
DO NOT TAMPER WITH PILOT LIGHT SAFETY SYSTEM
WARNING: If the information in this manual is not followed exactly, a fire or explosion may
result causing property damage, personal injury or loss of life.
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other
appliance.
WHAT TO DO IF YOU SMELL GAS
១
Do not try to light any appliance.
Do not touch any electrical switch; do not use any phone in your building.
Immediately call your gas supplier from a neighbor’s phone. Follow the gas
១
១
supplier’s instructions.
If you cannot reach your gas supplier, call the fire department.
១
Installation and service must be performed by a qualified installer, service agency or the gas supplier.
16-1000
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT INFORMATION
១
១
This appliance must not be installed in a bedroom or bathroom.
Do not use this room heater if any part has been under water. Immediately call a qualified
service technician to inspect the room heater and to replace any part of the control system
and any gas control system and any gas control which has been under water.
១
១
WARNING: When used without fresh air, heater may give off CARBON MONOXIDE, an
odorless poisonous gas.
Early signs of carbon monoxide poisoning resemble the flu. with headache, dizziness and/or
nausea. If you have these signs, heater may not be working properly. Get fresh air at
once! Have heater serviced.
១
Some people - pregnant women, persons with heart or lung disease, anemia, those under
the influence of alcohol and those at high altitudes are more affected by carbon monoxide
than others.
ATTENTION INSTALLER:
REVIEW AND LEAVE THESE INSTRUCTIONS WITH CUSTOMER
FOR FUTURE REFERENCE.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
COMBUSTION AND VENTILATION PROVISIONS
WARNING: This heater shall not be installed in a confined space or unusually tight construction unless
provisions are provided for adequate combustion and ventilation air.
Confined Space and Unconfined Space
The National Fuel Gas Code, ANSI Z223.1 defines a confined space as a space whose volume is less than
50 cubic feet per 1,000 Btu per hour (4.8m³ per kw) of the aggregate input rating of all appliances
installed in that space and an unconfined space as a space whose volume is not less than 50 cubic feet
per Btu per hour (4.8m³ per kw) of the aggregate input rating of all appliances in that space. Rooms
communicating directly with the space in which the appliances are installed, through openings not
furnished with doors, are considered a part of the unconfined space.
WARNING: If the area in which the heater may be operated is smaller than that defined as an
unconfined space or if the building is of unusually tight construction, provide adequate
combustion and ventilation air by one of the methods described in the National Fuel Gas Code,
ANSI Z223.1, Section 5.3 or applicable local codes.
Unusually tight construction is defined as construction where:
a. Walls and ceilings exposed to the outside atmosphere have a continuous water vapor retarder
-
with a rating of 1 perm (6 x10 ¹¹ kg per pa-sec-m²) or less with openings gasketed or sealed, and
b. Weather stripping has been added to openable windows and doors, and
c. Caulking or sealants are applied to areas such as joints around windows and door frames,
between sole plates and floors, between wall-ceiling joists, between wall panels, at penetrations
for plumbing, electrical and gas lines and at other openings.
Instructions for determining maximum Btu’s for a room
Step 1
This calculation is for combustion and ventilation air provisions only and is not intended to be used for
sizing for heating comfort. To determine the maximum Btu’s allowed for a given room size you will need
to calculate the volume of the room in cubic feet. To perform this calculation, fill in the table below and
multiply the room’s width, length and height to obtain the room volume in cubic feet.
ROOM
LENGTH
ROOM
WIDTH
ROOM
HEIGHT
ROOM VOLUME
IN CUBIC FEET
X
X
=
Example:If your room is 20 feet in length, 16 feet wide and has an 8 foot ceiling height, the
calculation would be as follows: 20 x 16 x 8 = 2,560 cubic feet.
Step 2
Divide the room volume by 50 cubic feet to determine the maximum Btu’s per hour the room can
utilize.
Example:Using the above example: 2,560 cubic feet divided by 50 = 51.2 x 1,000 = 51,200 Btu’s.
If the rate of your appliance plus any other gas appliances installed in the space is rated at more Btu’s
than the example calculated above, you must follow instructions for confined space. See shaded
WARNING above. If your appliance is rated at less Btu’s than the example calculated above, then your
area is considered unconfined space.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
The installation of this appliance must conform with local codes or, in the absence of local codes with
the National Fuel Gas Code, ANSI Z223.1.
NOTE: Before the unit is connected to any gas line, check the name plate on the unit for the proper
gas type you will be using.
Do not install this appliance in a bedroom or bathroom.
This appliance is equipped with a control valve that has an internal regulator, and is not intended to regulate
any gas pressure above ½psig. If using LP gas, a low pressure regulator (not furnished) must be installed in
the gas line between the tank and appliance. Do not connect the appliance to the gas line if this regulator is
not in place. If using natural gas, check with the gas company to insure that proper gas pressure is available.
GAS PRESSURE: Minimum inlet gas supply pressure must be 5.0” WC for natural gas or 11” WC for
LP gas for the purpose of input adjustment. Maximum inlet gas supply pressure must not exceed 10.5”
WC for natural gas, or 13” WC for LP gas. The gas line supplying the appliance must be sufficient size
to furnish the appropriate supply pressure to the appliance when being operated on the high setting.
១
The appliance and its appliance main gas valve must be disconnected from the gas supply
piping system during any pressure testing of that system at test pressures in excess of ½
psig (3.5kPa).
១
The appliance must be isolated from the gas supply piping system by closing its individual
manual shutoff valve during any pressure testing of the gas supply piping system at test
pressures equal to or less than ½psig (3.5kPa).
១
Always keep appliance area clear and free from combustible materials, gasoline and other
flammable vapors and liquids.
១
Pressure tap screws must be closed before turning on gas to appliance.
HEATER CLEARANCES FROM COMBUSTIBLES:
The minimum clearances to any combustible surface are: 1 inch from the left and right sides, 4 inches
from the rear, 24 inches from the front and 24 inches from the top of the heater. The left and right side
clearances are measured from the outside edge of the top of the heater. The front clearance is measured
from the front of the cabinet and the top measurement is measured from the top of the heater. The rear
clearance is measured from the back panel of the heater.
CLEARANCES AROUND AIR OPENINGS:
Do not place any material or store any objects behind the heater. After installation of the heater, do not
block the open area behind the heater in any way.
HEATER CLEARANCES FOR SERVICING:
The minimum clearances for servicing the heater are: 18 inches from the right side and 18 inches from
the rear of the heater.
This appliance may be installed in an aftermarket permanently located manufactured (mobile)
home, where not prohibited by state or local codes.
Aftermarket: Completion of sale, not for the purpose of resale, from the manufacturer.
This appliance is only for use with the type of gas indicated on the rating plate. This appliance is
not convertible for use with other gases.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTIONS
NOTE: It is recommended by the manufacturer that a qualified individual install this appliance.
Your new DiamondGlo heater is shipped in one box and the logs are shipped in a separate box. Packed
with the DiamondGlo heater is a thermostat that must be hooked to the appliance before it is operated.
Please follow the instructions on page 7 for the installation of this thermostat.
1. Remove DiamondGlo heater from the box by cutting bands around the box and lifting the box off
the heater.
2. Lift heater from the bottom of the box and place near the final location of the heater. CAUTION:
Lift heater when moving. Do not slide heater on the floor.
3. Locate thermostat that was packaged with the heater and see instructions on page 7 of these
instructions for installation of the thermostat.
4. The manufacturer has furnished a 3/8” flare brass fitting for connection to the gas line. If the gas
line is anything but a 3/8” flare connection, this fitting must be changed to the appropriate fitting by
the installer.
5. Connect the gas line to the fitting located at the back of the heater.
6. Remove the screen from the front of the heater by removing the screw from the middle top of the
screen, and pulling the screen off by pulling on the two brass knobs located on the bottom of the
screen.
7. Place the heater in its final location.
8. Make sure all gas connections are tight. Turn on gas and coat each joint with a soap and water
solution and watch for air bubbles which will indicate leaks. Any leaks must be corrected before
proceeding with installation. DO NOT USE A FLAME OR ANY IGNITION SOURCE TO
CHECK FOR LEAKS.
9. Your DiamondGlo heater was leak tested before it left the factory, but it is recommended to check
all connections for leaks.
10. Remove logs from box. Notice the notches in the larger logs and the numbers on the bottom of the
same logs. The log placement is very important to the safe operation of the appliance.
11. NOTE: For correct log placement, match the log placement photo in this manual with the model number
of your heater. The logs MUST be placed exactly as shown. If there is any evidence of carbon or blackening
on the logs, they may be incorrectly placed. There should not be any carbon or blackening on the logs at
any time.
12. Place the back log in the grooves on the elevated cradle toward the back of the grate making sure
the grooves in the bottom of the log fit on the cradle.
13. Place the middle log in the grooves on the center elevated section of the cradle making sure the
grooves in the bottom of the log fit on the cradle. This will position the middle log between the
burner.
14. Place the front log on the front of the grate in front of the cradle making sure the grooves on the
bottom and front of the log fit the bars on the grate.
15. Place the small top logs in the grooves on top of the front and back log, making sure these logs lay
across the middle log in the appropriate groove.
16. Match the model number of your heater with the heater model number on page 12 of this
instruction manual. The log placement should look like this. If it doesn’t, follow steps 10 through 16
above.
17. Replace the front screen on the heater by sliding the two sides into the notches and replacing the
screw in the top middle of the screen.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND OPERATING INSTRUCTIONS
THERMOSTAT - REMOTE CONTROL
THERMOSTAT
១
It is suggested by the manufacturer that a qualified individual make this installation.
១
Your DiamondGlo II and DiamondGlo JR is shipped from the factory with a thermostat included.
Follow these instructions for the installation and operation of this thermostat.
១
Locate the control valve at the back of the heater. Notice the electric terminals on the control
valve, located on the right hand side of the valve when facing the back of the heater. See FIG 1.
1. Decide where you want to mount the thermostat. The thermostat can be mounted directly to the
back of the heater using the bracket that is furnished with the thermostat or it can be located on a
wall adjacent to the heater. (The bracket can be discarded if the thermostat is mounted on the wall
adjacent to the heater.)
2. Run wire (included) from the log set to the location of the thermostat.
3. It is recommended that only the wire furnished with the thermostat is used.
4. You may cut the wire to the appropriate length needed, but it is recommended not to use any
additional wire, so locate the thermostat within the distance of the wire included.
5. Attach the two bare end wires to the wall thermostat.
TP TH
TP
TH
6. Make sure the ON/OFF lever on the wall thermostat is turned
OFF and mount the wall thermostat. The cover of the
thermostat snaps off for access to the mounting screw location.
7. Attach the two wires at the control valve to the two outside terminals on
the terminal block. See drawing at right. (FIG. 1) (Make sure the wall
thermostat is turned OFF.)
8. Follow the safety information on page 9 of this instruction manual.
9. Follow the lighting instructions on page 9 of this instruction manual.
FIG. 1
10. After lighting the pilot, turn the ON/OFF control knob (FIG. 4 on page 9) to the ON position and
the thermostat ON/OFF lever to the ON position. Adjust the temperature lever to the desired
position. You can now adjust the HI/LOW knob to the desired level. If you have the HI/LOW
control knob on “HI” the log set will burn on high flame when the thermostat calls for heat. If you
have the HI/LOW control knob on “LOW” the log set will burn on low flame when the
thermostat calls for heat.
11. You can allow the log set to operate by the thermostat setting or you can keep the log set from
operating by turning the ON/OFF lever to “OFF” on the thermostat.
12. It is recommended that the ON/OFF control knob (FIG. 4 on page 9) on the control valve be turned to
the “OFF” position when leaving home for any period of time.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
THERMOSTAT REMOTE CONTROL
១
Remove screen from front of heater. Place the remote control receiver on the floor of the heater,
over next to the inside wall of the heater. Run the two wires from the receiver through the
opening in the floor of the heater so they can be connected to the valve. ( NOTE: Make sure the
wires are placed so they are not close to any flames on the burner.)
១
It is recommended by the manufacturer that a qualified individual install this device.
១
The DiamondGlo II and DiamondGlo Jr. are shipped from the factory with a thermostat
included. If using the Thermostat Remote Control, the thermostat package, including the wire
can be discarded.
១
Locate the control valve located at the back of the heater. Notice the electric terminals on the
control valve, located on the right hand side of the valve when facing the back of the heater. See
FIG. 2.
1. Follow the instructions supplied with the Thermostat Remote Control.
TP TH
TP
TH
This is a millivolt gas valve.
It is recommended by Heatmaster, Inc. that all precautions are
followed exactly. (NOTE: In the instructions supplied with the remote
control, there are instructions on a crackling sound system. This is an
optional system and is not available from Heatmaster, Inc.)
2. Follow the safety information on page 9 of this instruction manual.
3. Follow the lighting instructions on page 9 of this instruction manual.
4. After lighting the pilot, turn the ON/OFF control knob (FIG. 4 on
page 9) to the “ON” position. You may now operate your log set
FIG. 2
according to the remote control instructions. You can now adjust the HI/LOW knob to the desired
level. If you have the HI/LOW control knob on “HI”, thelog set will burn on high flame when the
remote control calls for heat. If you have the HI/LOW control knob on “LOW” the log set will
burn on low flame when the remote control calls for heat.
5. It is recommended that you turn the ON/OFF control knob (FIG. 4 on page 9) on the control
valve to the “OFF” position when leaving home for any period of time.
FAN OPERATION
Your heater can be operated without the fan running in the event of a power failure.
Your heater is equipped with a built-in thermostat that will cause the fan to operate with the burner unit
in the heater. The heater may need to operate approximately 5 minutes before the fan thermostat allows
the fan to come on. After the burner shuts off, the fan may continue to run for approximately 5 minutes
before the fan thermostat allows it to cut off. The fan is designed to operate with the burner unit of the
heater automatically as long as the electrical cord is plugged in.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage,
personal injury or loss of life.
A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly.
This appliance is equipped with a push button piezo ignition device which can be used to light the pilot. If the piezo
fails to ignite the pilot, then follow the instructions for lighting pilot with match.
B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some
gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
១ Do not try to light any appliance.
១ Do not touch any electrical switch; do not use any phone in your building.
១ Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
១ If you cannot reach your gas supplier, call the fire department.
C. Use only your hand to push in or turn the gas control handle, Never use tools. If the handle will not push in or turn
by hand, do not try to repair it. Call a qualified service technician. Force or attempted repair may result in fire or
explosion.
D. Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system and any gas control which has been under water.
LIGHTING INSTRUCTIONS
1. STOP! Read the safety information previously listed above.
2. Make sure the thermostat or remote control is in the “OFF” position.
3. Turn ON/OFF control knob (FIG. 4) clockwise
to the “OFF” position. Do not force.
4. Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow
“B” in the safety information above on this label. If you don’t smell gas, go to the next step.
5. Locate pilot (Fig. 3) - mounted on the outside of the right hand bracket that holds the burner in place, just behind
the front part of the burner.
6. Turn ON/OFF control knob (FIG. 4) counterclockwise
to the “PILOT” position.
7. Push down on ON/OFF (FIG. 4) control knob until it stops and hold down. While still holding down on the knob,
press down on the igniter push button (FIG. 4) several times. This will cause a spark at the pilot burner which will
ignite the pilot flame. Continue to hold the ON/OFF control knob (FIG. 4) down for about (1) minute after the pilot
is lit. Release knob and it will pop back out. Pilot should remain lit. If it goes out, repeat steps 1 through 6.
១
If the knob does not pop out when released, stop and immediately call your service technician or gas supplier.
If the pilot will not stay lit after several tries, turn the gas control handle to “OFF” and call your service technician or
gas supplier.
១
១
LIGHTING PILOT WITH MATCH: Remove screen from the front of the heater. Turn ON/OFF control knob (FIG.
4) counterclockwise
to “PILOT”. Place a lit match at the pilot burner, then push the
ON/OFF control knob (FIG. 4) down until it stops. Continue to hold the control knob in for about one (1) minute
after the pilot is lit. Release knob and it will pop back out. Pilot should remain lit. If it goes out, repeat the
above step.
១
១
Replace screen on the front of the heater.
If the pilot will not stay lit after several tries, turn the ON/OFF control knob (FIG. 4) clockwise
call your service technician or gas supplier.
to “OFF” and
8. To turn the main burner on, turn ON/OFF control knob counterclockwise
to the “ON” position.
9. Adjust the heater to high or low by turning the HI/LOW control knob (FIG. 4).
10. Adjust thermostat to the desired setting.
TO TURN OFF GAS TO APPLIANCE
ON/OFF
CONTROL KNOB
Turn ON/OFF control knob (FIG. 4) clockwise
to the “OFF” position. Do not force.
PILOT BURNER
IGNITOR
LOW
PILOT
IGNITER
PUSH BUTTON
HI/LOW
CONTROL KNOB
HI
Fig. 3
Fig. 4
9
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEANING AND MAINTENANCE INSTRUCTIONS
ALWAYS REMEMBER:
1. Do not place any combustible material near the appliance.
2. Do not place any paper, trash or other material on the log set or in the heater.
3. Do not touch any part of the appliance when the unit is in operation.
Your heater is designed to be virtually maintenance free, although periodic visual inspection and
cleaning is required. Follow the instructions below for the correct procedures.
If at any time the flames on your log set look abnormal or an odor is noticed that coming from the
appliance, contact a qualified service technician or the gas company.
Periodically, visually inspect the main burner flames as well as the pilot flame. The appearance of these
flames should resemble the drawings on page 11 (FIG. 5 and FIG. 6 or FIG. 7). Any measurements are
approximate. Flame heights may vary.
To ensure that your unit operates at peak performance, inspect and clean it at least monthly during the
heating season by following the guidelines below. More frequent cleaning may be required due to
excessive lint from carpeting, bedding material, etc. It is imperative that control compartments, burners
and circulating air passageways of the appliance be kept clean.
CAUTION: Before cleaning the appliance, be sure it is turned completely off. The pilot should also be
turned off. The unit must be completely cooled.
DO NOT USE ANY CLEANING FLUIDS OR TOOLS FOR CLEANING PURPOSES
1. Remove front screen.
2. Remove logs from front assembly and place on the floor close to the heater.
3. Lightly vacuum any loose particles or dust from the grate and burner. Pay close attention to the air
opening at the beginning of the main burner. This opening is located at the point of the main burner
where the gas line from the control valve is attached. This opening must remain free of any
obstruction.
4. Lightly vacuum any loose particles or dust from the pilot flame area, being sure not to touch any part
of the pilot with the vacuum.
5. Lightly vacuum any dust from the logs.
6. Carefully replace logs on the grate assembly and relight the pilot as stated in this instruction manual.
NOTE: If any of the appliance parts are hit with the vacuum during cleaning, a gas leak could occur. If
this happens, be sure to check for leaks as described on page 6 of this instruction manual.
FAN MOTOR LUBRICATION
១
It is recommended by the manufacturer that the fan motor be re-lubricated every six (6)
months.
១
Use six (6) drops of a #20 non-detergent oil when re-lubricating.
1. Unplug the heater from the electric wall outlet.
2. Remove the fan cover from the back of the heater.
3. While looking at the back of the heater, notice the notch that is punched in the end of the
motor at the 2 o’clock position. This notch is also punched at the other end of the motor in
the same position.
4. Notice the location of the motor brackets, because the motor must be re-installed exactly as
you remove it.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Remove the three (3) screws that hold the fan motor in place.
6. Slowly pull the motor and fan wheel out from the back of the heater.
7. Look between the fan wheel and the end of the motor and locate the notches referenced
above in item 3.
8. Put six (6) drops of oil in the notch at each end of the motor.
9. Replace the motor with the brackets in the same location as they were
mounted at the factory.
10. Replace the fan cover on the back of the heater.
11. Plug the heater back into the electric wall outlet.
NATURAL GAS
PROPANE GAS
Fig. 5
DiamondGlo Jr.
DiamondGlo II
Fig. 6
Fig. 7
11
Download from Www.Somanuals.com. All Manuals Search And Download.
LOG PLACEMENT PHOTOS
3
4
2
5
1
6
HMDGJR with RO Logs
HMDGJR with RO Logs
HMDGJR with SO Logs
HMDGII with RO Logs
HMDGII with SO Logs
9
10
11
7
12
8
HMDGJR with SO Logs
19
15
18
16
17
13
14
HMDGII with RO Logs
25
22
23
24
20
21
HMDGII with SO Logs
WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts
specifically approved with this heater may result in property damage or personal injury.
The logs MUST be placed exactly as shown.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
LOG PARTS LIST
KEY
KEY
LETTER
LETTER PART NO.
DESCRIPTION
PART NO.
DESCRIPTION
1
2
3
4
5
6
7
8
Log # 429
Log # 430
Log # 431
Log # 432
Log # 444
Log # 409
Log # 439
Log # 440
Log # 441
Log # 416
Log # 438
Log # 415
Front Log
Middle Log
Back Log
Right Log
Left Log
Middle Top Log
Front Log
Middle Log
Back Log
Right Log
Left Log
13
14
15
16
17
18
19
20
21
22
23
24
25
Log # 426
Log # 427
Log # 428
Log # 410
Log # 409
Log # 424
Log # 408
Log # 435
Log # 436
Log # 437
Log # 416
Log # 438
Log # 415
Front Log
Middle Log
Back Log
Right Log
Left Bottom Log
Left Top Log
Middle Top Log
Front Log
Middle Log
Back Log
Right Log
Left Log
Middle Top Log
9
10
11
12
Middle Top Log
13
Download from Www.Somanuals.com. All Manuals Search And Download.
A connection wiring diagram to aid in locating components.
FIG. 13
120
VOLTS
MOT
A schematic wiring diagram of ladder form.
FIG. 14
CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause
improper and dangerous operation.
Verify proper operation after servicing.
WARNING
Electrical Grounding Instructions
This appliance is equipped with a three-prong (grounding) plug for your protection against shock hazard
and should be plugged directly into a properly grounded three-prong receptacle.
If any of the original wire supplied with the appliance must be replaced, it MUST be replaced with type
SPT-2 wire or its equivalent.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS DRAWING
ZZ
N
A10
A5
A1
W
A6
RR
W
IGNITOR WIRE
to ignitor tip
A4
B
VALVE MOUNTING
BRACKET (T)
A3
TT
XX
NN
W
A21
Z
A
W
O
DD
Y
T
LL
G
J
MM
Q
DD
GG
R
K
THERMOSTAT PACKAGE
H
C
E
O
JJ
A2
EE
II
O
TEMP
OFF
ON
90
70
50
S
I
I
D
J
F
P
G
F
L
FF
U
HH
W
U
W
SS
N
N
FLOOR PANEL
BURNER ASSEMBLY
VALVE
AA
X
YY
NATURAL GAS
PILOT LINE
REGULATOR
BB
UU
VV
WW
VV
UU
UU
A9
CC
MM
PP
OO
U
KK
MM
TT
W
NN
A7
V
IGNITOR WIRE
to push button
O
NN
W
A8
NN
15
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY
LETTER
PART
NO.
KEY
LETTER
PART
NO.
DESCRIPTION
DESCRIPTION
A
A
B
B
C
D
E
F
16-1150 Heater Back - DGII *
16-1250 Heater Back - DGJr *
11-1136 Heater Top - DGII *
16-1136 Heater Top - DGJr *
02-1040 Junction Box
16-1500 Junction Box Cover & Mount
07-1013 Junction Box Screw 6-32 x 3/8"
11-1412 Brass Trim 3/4" x 17 - DGII
16-1400 Brass Trim 3/4" x 12 7/8 - DGJr
11-1410 Brass Trim 3/4" x 8 1/32" - DGII
(Side Louver)
16-1410 Brass Trim 3/4" x 5 3/4" - DGJr
(Side Louver)
11-1413 Brass Trim 3/4" x 17 15/16" - DGII
(Front Louver)
16-1415 Brass Trim 3/4" x 13 1/2" - DGJr
(Front Louver)
11-1415 Brass Trim 1/2" x 38 1/4" - DGII
16-1420 Brass Trim 1/2" x 29 7/8" - DGJr
11-1138 Side Louver - DGII *
16-1138 Side Louver - DGJr *
11-1139 Front Louver - DGII *
16-1139 Front Louver - DGJr *
16-1300 Front Screen - DGII
16-1350 Front Screen - DGJr
02-1060 8-32 x 3/4" Pointed Phillips Head
11-1440 Brass Decorative Knob
02-1075 8-32 Keeps Nut
11-1401 Name Plate
16-1032 3" Control Knob Extender HI/LO
11-1450 8-32 x 3" Screws
11-1403 Push-On Nut
16-1505 Valve Assembly Monuting Bracket
11-1445 8-32 x 5/16" Screw
AA
BB
CC
DD
EE
FF
GG
HH
II
01-1004 Brass Fitting 3/8 NPT x 3/8 FL
11-1036 Orifice
11-1036 Orifice
11-1505 10-32 Keeps Nut
16-1530 Thermostat
16-1540 120volt AC - Electric Cord
04-1012 10-32 x 1 1/4" Screw
16-1550 Thermostat Bracket
04-1009 8-32 x 1/2" Pointed Head Phillips Screw
02-1056 Insulated Wire Nut
11-1181 Burner - DGII
F
G
JJ
KK
KK
LL
G
H
H
11-1182 Burner - DGJr
01-1158 10-32 x 1/4" Screw
01-1080 10-32 x 1/2" Screw
01-1095 10-32 Nut
03-1000 Pilot Tubing - LP
03-1000 Pilot Tubing - Nat
16-1040 ODS Pilot - LP gas # 8404
16-1045 ODS Pilot - Nat gas # 8214
11-1164 Piezo Ignitor
MM
NN
OO
OO
PP
PP
RR
SS
TT
UU
VV
WW
XX
YY
YY
ZZ
A1
A2
A3
A4
A5
A6
A7
A8
A8
A9
I
I
J
J
16-1600 Bottom Cover Plate
16-3600 Piezo Wire - 36"
K
K
L
11-1076 3/16" Nut & Ferrule
11-1155 3/16" MPT Connector
11-1150 Pilot Regulator - Nat gas ONLY
16-1031 3" Control Knob Extender
16-1030 Millivolt Valve - LP gas
16-1035 Millivolt Valve - Nat gas
16-1560 Fan Cover
11-1460 Rubber Grommet
02-1058 Strain Relief - Small
16-1201 Strain Relief - Large
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Nov-01
8x1 s/drill
14-1202 Control Knob
11-1465 Flat Washer
16-1110 Pilot Burner Bracket - LP gas
16-1510 Grate DGII
16-1515 Grate DG Jr.
16-1200L Burner & Log Support - DGII
06-1032 #8 x 1/2" Std. Screw
07-1020 90deg Street Elbow
11-1395 Thermodisc
16-1520 Valve Control Rods ( 1/4" x 1/4" sq.)
11-1441 Loxit Nut & Sleeve
Parts may be ordered directly from:
HEATMASTER, INC.
3625 Benson Road, P.O. Box 1717
Angier, NC 27501
(919) 639-4568
When ordering, please include complete part number, part name and description.
* Specify COLOR - Grey or Almond
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|