Graco Marine Instruments g250 User Manual

Instructions-Parts  
Volumetric Fluid Flow  
Meter  
308778L  
For precise metering of plural component fluids and solvents.  
See page 2 for model information, including maximum working pressure.  
Important Safety Instructions  
Read all warnings and instructions in this  
manual. Save these instructions.  
G3000 and G3000HR  
(Model 289813 with 90°  
Recognized Component  
Sensor Connector Shown)  
9902471  
Conforms to UL2279  
Certified to  
TI11579a  
CAN/CSA E79-0  
CAN/CSA E79-11  
EExia II A T3  
ITS03ATEX21212  
II 1 G  
G250 and G250HR  
*
0359  
Intrinsically Safe for Hazardous Locations (Class I; Division 1;  
Group D) when used with an approved barrier only.  
*
CE mark approvals only apply to meters used as part of Graco  
ProMix, ProMix 2KS, and PrecisionMix II Systems.  
TI13038a  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Warnings  
Warnings  
The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama-  
tion point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back  
to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where  
applicable.  
WARNING  
SKIN INJECTION HAZARD  
High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like just  
a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment.  
Do not point gun at anyone or at any part of the body.  
Do not put your hand over the spray tip.  
Do not stop or deflect leaks with your hand, body, glove, or rag.  
Do not spray without tip guard and trigger guard installed.  
Engage trigger lock when not spraying.  
Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning,  
checking, or servicing equipment.  
FIRE AND EXPLOSION HAZARD  
Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent  
fire and explosion:  
Use equipment only in well ventilated area.  
Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop  
cloths (potential static arc).  
Keep work area free of debris, including solvent, rags and gasoline.  
Do not plug or unplug power cords, or turn power or light switches on or off when flammable fumes  
are present.  
Ground all equipment in the work area. See Grounding instructions.  
Use only grounded hoses.  
Hold gun firmly to side of grounded pail when triggering into pail.  
If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment  
until you identify and correct the problem.  
Keep a working fire extinguisher in the work area.  
SPECIAL CONDITIONS  
Equipment must comply with the following conditions to avoid a hazardous condition which can cause  
fire, explosion, or electric shock:  
Never use the flow meter with an electrostatic gun isolation stand.  
Keep liquids away from the electronic sensor device.  
Do not service the electronic sensor. Return it to your Graco distributor for service.  
PRESSURIZED EQUIPMENT HAZARD  
Fluid from the gun/dispense valve, leaks, or ruptured components can splash in the eyes or on skin and  
cause serious injury.  
Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning,  
checking, or servicing equipment.  
Tighten all fluid connections before operating the equipment.  
Check hoses, tubes, and couplings daily. Replace worn or damaged parts immediately.  
308778L  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Warnings  
WARNING  
EQUIPMENT MISUSE HAZARD  
Misuse can cause death or serious injury.  
Do not operate the unit when fatigued or under the influence of drugs or alcohol.  
Do not exceed the maximum working pressure or temperature rating of the lowest rated system  
component. See Technical Data in all equipment manuals.  
Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all  
equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information  
about your material, request MSDS forms from distributor or retailer.  
Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manu-  
facturer’s replacement parts only.  
Do not alter or modify equipment.  
Use equipment only for its intended purpose. Call your distributor for information.  
Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.  
Do not kink or over bend hoses or use hoses to pull equipment.  
Keep children and animals away from work area.  
Comply with all applicable safety regulations.  
TOXIC FLUID OR FUMES HAZARD  
Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or  
swallowed.  
Read MSDS’s to know the specific hazards of the fluids you are using.  
Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.  
Always wear impervious gloves when spraying or cleaning equipment.  
PERSONAL PROTECTIVE EQUIPMENT  
You must wear appropriate protective equipment when operating, servicing, or when in the operating  
area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic  
fumes, burns, and hearing loss. This equipment includes but is not limited to:  
Protective eyewear  
Clothing and respirator as recommended by the fluid and solvent manufacturer  
Gloves  
Hearing protection  
4
308778L  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation  
Installation  
Installing the Flow Meter  
Flow volume can only be measured at the location  
where the flow meter is installed.  
All electrical equipment must only be installed by  
a qualified electrician.  
The Fluid Flow Meters are intrinsically safe for Class  
I; Division 1; Group D hazardous indoor (NEMA 1)  
locations when installed with an intrinsically safe  
power device and wiring.  
Understand and follow your local code and safety  
regulations for hazardous location wiring of intrin-  
sically safe circuits.  
Refer to ANSI standards ISA-RP12.6, NEC Article  
504 and the Canadian Electrical Code Appendix F.  
Dust and Foreign Matter  
Avoid having dust or foreign matter enter the flow meter  
by taking the following precautions:  
Do not use more than 200 ft. (61 m) of cable.  
Refer to FIG. 1 to locate and install the flow meter,  
connectors, and fluid shutoff valves. Install a check  
valve to prevent backflow. The arrows on the flow  
meter and check valve show the direction of fluid  
flow.  
Thoroughly flush the fluid supply lines before install-  
ing the flow meter.  
When installing fittings, make sure that no sealing  
tape overlaps into the inside of the pipe.  
The shutoff valves allow you to isolate the meter for  
service.  
Install a 100 mesh fluid filter upstream of the flow  
meter.  
Drawings for dimension, inlet/outlet size, tempera-  
ture and other specifications.  
Cable  
Electronic Sensor Device  
Flow Meter  
Ground Sheath  
Fluid Shutoff Valve  
on outlet side  
Fluid Line  
Check Valve  
Fluid Shutoff Valve  
on outlet side  
7379A  
FIG. 1: Typical Installation  
308778L  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Installation  
Grounding  
1. Ground the flow meter by connecting a grounded  
cable to the sensor.  
Have a qualified electrician check the electrical  
grounding continuity between the flow meter sensor  
and a true earth ground; remove the cable connec-  
tor from the sensor and measure the resistance  
from the cable connector Pin B to true earth ground.  
Refer to FIG. 2.  
If the resistance is greater than 25 ohms, check the  
cable ground connection. Refer to FIG. 2. Reconnect  
the ground sheath or replace the cable. Do not oper-  
ate the system until the problem is corrected.  
2. Always ground the fluid supply unit, using one of the  
following options:  
a. Mount the meter to a grounded conductive sur-  
face, or  
b. Connect the conductive fluid hose to the meter  
inlet and outlet, or  
c. Connect a ground wire to the meter's M6  
mounting holes.  
3. Never use the flow meter with an electrostatic gun  
isolation stand.  
A
B
C
+10-30 Vdc Supply (red)  
Ground (black)  
Signal Out (white)  
C
A
B
7379A  
FIG. 2  
6
308778L  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Operation  
Operation  
Pressure Relief Procedure  
Flow Volume Range  
The G3000 and G250 meters flow volume range is  
0.02-1.0 gal./min. (75-3800 cc/min.).  
The G3000HR and G250HR meters flow volume range  
is 0.01-0.5 gal./min. (38-1900 cc/min.).  
1. Shut off the fluid supply to the meter.  
NOTICE  
2. Shut off all electrical power to the fluid system.  
The flow meter gears and bearings can be damaged  
if they rotate at too high a speed. To avoid high speed  
rotation, open the fluid valve gradually. Do not  
over-speed the meter with air or solvent. To prolong  
meter life, do not exceed the meter’s maximum flow  
rate.  
3. Follow the Pressure Relief Procedure for your fluid  
system dispensing device.  
Flow Meter Function  
This is a positive displacement, gear flow meter. The  
gear flow meter is highly accurate, even with low flow  
rates. The fluid flowing through the meter rotates the  
gears. The gear tooth is picked up by a sensor device,  
which produces an impulse for every gear tooth passing  
by.  
Checking the Meter Accuracy  
1. To check the accuracy of the meter, turn your gun  
fan and atomizing air off, then trigger the fluid into a  
graduated cylinder; dispense at least 500 cc of fluid.  
2. Measure the volume of fluid in the beaker in  
cubic-centimeters (cc) and read the volume on the  
flow meter monitor.  
Recommended Usage  
G3000 and G250: If the flow meter scale factor is  
not between 0.112-0.140 cc/pulse, follow the clean-  
ing procedure on page 10, then recalibrate the flow  
meter.  
Do not exceed the maximum working pressure of your  
meter or any component or accessory in your system.  
G3000HR and G250HR: If the flow meter scale fac-  
tor is not between 0.05-0.07 cc/pulse, follow the  
cleaning procedure on page 10, then recalibrate the  
flow meter.  
See the Technical Data for fluid and ambient tem-  
perature limits.  
Only use the flow meter with fluids that are compati-  
ble with the “Wetted Parts” listed in the Technical  
Data.  
308778L  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Troubleshooting  
Troubleshooting  
Before servicing this equipment always make sure to  
relieve the pressure.  
NOTICE  
The sensor is not a serviceable part. Replace it if it is  
malfunctioning.  
Problem  
Cause  
Solution  
No flow volume displayed at monitor- Flow volume is too low to measure.  
Increase flow volume.  
Repair.  
ing unit.  
Fluid is not flowing.  
Damaged cable.  
Replace cable.  
Improper input voltage to sensor.  
Damaged sensor.  
Make sure input voltage is 10-30 Vdc.  
Replace sensor if it is malfunctioning.  
Fluid is not flowing.  
Clogs in fluid line or in meter.  
Clean fluid line and/or meter; see  
Maintenance on page 9.  
Gears worn or damaged.  
Repair meter; see Maintenance on  
page 9.  
8
308778L  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Maintenance  
Maintenance  
Flushing  
If the meter is not installed in an instrinsically safe  
location, make sure the power is off or the electronic  
sensor is disconnected before wiping the outside of  
the meter clean with a cloth dampened in a compati-  
ble solvent or flushing the meter.  
Flush the fluid supply line and meter fluid reservoir daily  
with a compatible solvent as instructed below.  
1. Follow the Pressure Relief Procedure, on page 7.  
2. Connect the fluid line to the solvent supply unit.  
3. Flush the meter until it is clean.  
NOTICE  
Do not immerse the meter in solvent with the elec-  
tronic sensor installed. Solvent could damage the  
electrical components.  
4. Follow the Pressure Relief Procedure, then dis-  
Air purge is not recommended for any gear-type flow  
meter. Air purges do not provide the lubrication the  
meter gears require.  
connect the fluid line from the solvent supply unit.  
5. Reconnect the fluid line to the fluid (paint) supply.  
6. Turn on the fluid supply.  
Residue Build-up on the Meter  
Gears  
7. Operate until the meter and fluid line are free of sol-  
vent.  
Residue build-up may cause the meter gears to bind or  
stop rotating, which decreases the meter accuracy and  
makes meter recalibration necessary. As more build-up  
occurs, recalibration is required more often.  
The frequency that your meter requires cleaning  
depends on the type of fluid being used. Excessive resi-  
due build-up usually means that you are using improper  
cleaning solvents and/or cleaning sequences or pro-  
cesses.  
Check the meter routinely to develop the correct  
cleaning schedule.  
Use the proper cleaning solvent for the fluid being  
metered.  
308778L  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Maintenance  
Cleaning or Servicing the Meter  
Chamber  
NOTICE  
To avoid damaging the shafts, keep the housings par-  
allel to each other when separating them; do not rock  
the housings from side to side. Do not use chisels or  
screwdrivers to split and pry apart the housings.  
NOTICE  
Clean and service the meter at a clean workbench.  
Use only lint-free cloth on parts.  
7. Remove and inspect the gears and shafts. Clean  
the meter parts with solvent.  
8. Reassemble the gears and shafts into the lower  
housing in the position they were removed from.  
Check the gears for free and easy rotation.  
Installing and servicing this equipment requires  
access to parts that may cause electric shock or other  
serious injury if the work is not performed properly. Do  
not install or service this equipment unless you are  
trained and qualified.  
9. Make sure the two locating pins are in place.  
10. Assemble the two meter housings, making sure to  
keep them parallel to each other.  
11. Install the screws. Tighten them oppositely and  
evenly, to 12 ft-lb (16 N•m). Do not over-tighten.  
Use only genuine Graco replacement parts. Substitu-  
tion of components may impair intrinsic safety. This  
could result in a failure which causes serious injury  
and/or substantial property damage.  
12. After re-assembling the meter, test the gear rotation  
by applying a brief air blast to the meter inlet. You  
should clearly hear the gears spin.  
13. Set the electronic sensor on the upper housing and  
tighten the two screws hand-tight, about 3.5 ft-lb  
(4.7 N•m). Do not over-tighten.  
1. Follow the Pressure Relief Procedure, on page 7.  
Then close the fluid shut-off valve on each side of  
the meter.  
2. Disconnect the cable from the electronic sensor  
device.  
3. Disconnect both fluid line fittings and remove the  
meter from the fluid line.  
4. Loosen the two screws and remove the electronic  
sensor device from the flow meter upper housing.  
See the Parts drawings, pages 12-14.  
5. Loosen the screws. Keep a few threads of two  
opposing bolts engaged to minimize the torque  
stress on the shafts when you separate the meter  
housings.  
6. Hold onto the upper housing and gently tap the  
opposing bolts to separate the lower housing.  
10  
308778L  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Parts  
Parts  
Flow Meter Kits, for ProMix 2KS Wall Fluid Panel  
15V804 G3000 Meter Kit  
15V827 G3000HR Meter Kit  
101  
104  
105  
110  
109  
108  
106  
TI12427a  
Ref.  
No.  
Part No. Description  
Qty  
101  
289813 METER, gear, G3000; used on  
15V804; see page 12  
1
289814 METER, gear, G3000HR; used  
on 15V827; see page 12  
1
104  
105  
501867 VALVE, check  
1
1
234628 HARNESS, cable, with connec-  
tor  
106  
114182 SCREW, machine, hex flange  
hd; M6 x 10; 16 mm  
2
108  
109  
15U749 BRACKET, mounting  
1
1
15U750 TUBE, assembly; sst; 1/2 in.  
(13 mm) OD tube x 1/4 npt  
110  
C19798 SCREW, cap, socket-hd; 1/4-20  
x 3/8 in. (10 mm)  
4
308778L  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Parts  
Bare Meter Assemblies  
289813 G3000 Meter, with 90° sensor connector  
289814 G3000HR Meter, with 90° sensor connector  
Ref.  
1
1
No. Part No. Description  
Qty.  
1
114100 SCREW, socket-hd; M4 x 55 mm  
long  
2
2
3
249430 ELECTRONIC SENSOR  
239719 GEAR METER ASSEMBLY;  
includes items 4-11; used on  
289813  
1
1
2
244291 GEAR METER ASSEMBLY;  
includes items 4-11; used on  
289814  
1
4
5
7
8
110580 • SCREW  
12  
1
1
2
2
2
2
2
1
*
• HOUSING, upper  
4 2  
110588 • O-RING; ptfe  
239718 • GEAR; used on 289813  
244290 • GEAR; used on 289814  
192383 • SHAFT, gear; used on 289813  
197142 • SHAFT, gear; used on 289814  
192387 • PIN, locating  
9
10  
11  
5
7
*
• HOUSING, lower  
*
Not a replacement part. Order item 3, gear meter  
assembly.  
Item 3, Gear  
Meter Assembly  
includes items  
4-11  
10  
8
9
11  
TI11580a  
1
2
Torque to 27-57 in-lb (3.1-6.4 N•m).  
Torque to 140-170 in-lb (15.8-19.2 N•m).  
12  
308778L  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Parts  
239716 G3000 Meter  
244292 G3000HR Meter  
Ref.  
1
No. Part No. Description  
Qty.  
1
1
114100 SCREW, socket-hd; M4 x 55 mm  
long  
2
2
3
239717 ELECTRONIC SENSOR  
239719 GEAR METER ASSEMBLY;  
includes items 4-11; used on  
239716  
1
1
2
244291 GEAR METER ASSEMBLY;  
includes items 4-11; used on  
244292  
1
4
2
4
5
7
8
110580 • SCREW  
12  
1
1
2
2
2
2
2
1
*
• HOUSING, upper  
5
7
110588 • O-RING; ptfe  
239718 • GEAR; used on 239716  
244290 • GEAR; used on 244292  
192383 • SHAFT, gear; used on 239716  
197142 • SHAFT, gear; used on 244292  
192387 • PIN, locating  
9
Item 3, Gear  
Meter Assembly  
includes items  
4-11  
10  
11  
*
• HOUSING, lower  
*
Not a replacement part. Order item 3, gear meter  
assembly.  
8
9
10  
11  
TI7381a  
1
Torque to 27-57 in-lb (3.1-6.4 N•m).  
Torque to 140-170 in-lb (15.8-19.2 N•m).  
2
308778L  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Parts  
249426 G250 Meter  
249427 G250HR Meter  
Ref.  
No. Part No. Description  
Qty.  
1
2
4
5
111308 SCREW, cap, socket-hd  
HOUSING, upper  
110588 O-RING; ptfe  
239718 GEAR; used on 249426  
244290 GEAR; used on 249427  
192383 SHAFT, gear; used on 249426  
197142 SHAFT, gear; used on 249427  
192387 PIN, locating  
4
1
1
2
2
2
2
2
1
1
2
1
1
*
20  
21  
1
6
7
8
11  
20  
21  
22  
*
HOUSING, lower  
15F866 SPACER  
119839 SCREW, cap, socket-hd; M4x65  
294430 ELECTRONIC SENSOR  
249428 GEAR METER ASSEMBLY;  
includes items 1-11; used on  
249426  
1
2
249429 GEAR METER ASSEMBLY;  
includes items 1-11; used on  
249427  
1
11  
2
Item 22, Gear  
Meter Assembly  
includes items  
1-11  
*
Not a replacement part. Order item 22, gear meter  
assembly.  
6
5
4
7
8
TI11580a  
1
Torque to 27-57 in-lb (3.1-6.4 N•m).  
Torque to 140-170 in-lb (15.8-19.2 N•m).  
2
14  
308778L  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Dimensions  
Dimensions  
G3000 and G3000HR  
G250 and G250HR  
Mounting Holes (bottom view)  
Mounting Holes (bottom view)  
M6  
M6  
1.73 in.  
(43.94 mm)  
1.73 in.  
(43.94 mm)  
Part Nos. 289813 and 289814  
Part Nos. 249426 and 249427  
3.75 in.  
(95.25 mm)  
1/4-18 npt(f)  
inlet/outlet  
4.00 in.  
(101.6 mm)  
1.92 in.  
(48.77 mm)  
2.16 in.  
(54.86 mm)  
1/4-18 npt(f)  
inlet/outlet  
2.47 in.  
(62.74 mm)  
2.97 in.  
(74.44 mm)  
Part Nos. 239716 and 244292  
4.69 in.  
(119.13 mm)  
1/4-18 npt(f)  
inlet/outlet  
2.16 in.  
(54.86 mm)  
2.97 in.  
(74.44 mm)  
308778L  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Technical Data  
Technical Data  
Maximum Fluid Working Pressure  
G3000 and G3000HR. . . . . . . . . . . . . . . . . . . . . . .  
G250 and G250HR. . . . . . . . . . . . . . . . . . . . . . . . .  
Flow Range  
4000 psi (28 MPa, 276 bar)  
250 psi (1.72 MPa, 17.2 bar)  
G3000 and G250 . . . . . . . . . . . . . . . . . . . . . . . . . .  
G3000HR and G250HR . . . . . . . . . . . . . . . . . . . . .  
Fluid Temperature Range . . . . . . . . . . . . . . . . . . . . . . .  
Maximum Ambient Temperature . . . . . . . . . . . . . . . . . .  
Fluid Viscosity Range . . . . . . . . . . . . . . . . . . . . . . . . . .  
Maximum Cable Length . . . . . . . . . . . . . . . . . . . . . . . .  
Flow Meter Inlet/Outlet . . . . . . . . . . . . . . . . . . . . . . . . .  
Resolution  
0.02-1.0 gal/min (75-3800 cc/min)  
0.01-0.5 gal/min (38-1900 cc/min)  
40-180°F (4-80°C)  
180°F (80°C)  
20-3000 cps (see Pressure Drop Curve on page 17)  
200 ft (61 m)  
1/4 npt(f)  
G3000 and G250 . . . . . . . . . . . . . . . . . . . . . . . . . .  
G3000HR and G250HR . . . . . . . . . . . . . . . . . . . . .  
Accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
Intrinsic Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
0.119 cc/pulse  
0.061 cc/pulse  
+/- 0.5%*  
10-30 Vdc  
Class I; Div. 1; Group D  
V max = 30 V  
I max = 15 mA  
Ci = 0.2 microfarads  
Li = 0 mH  
Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
Wetted Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
Weight  
See front cover  
303 Stainless Steel, Tungsten Carbide, PTFE  
G3000 and G3000HR. . . . . . . . . . . . . . . . . . . . . . .  
G250 and G250HR. . . . . . . . . . . . . . . . . . . . . . . . .  
6 lb (2.7 kg)  
2.6 lb (1.8 kg)  
*
For most commonly used coatings, the flow meter reading will be accurate to within +/- 0.5%. Accuracy will dimin-  
ish at low viscosities and low flow rates.  
16  
308778L  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Pressure Drop Curve  
Pressure Drop Curve  
PSI  
140  
130  
120  
110  
500 cps  
100  
90  
400 cps  
80  
300 cps  
200 cps  
70  
60  
50  
40  
30  
20  
100 cps  
50 cps  
10  
0
G3000/G250  
0.0 0.1  
0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1  
GAL/MIN  
GAL/MIN  
G3000HR/G250HR  
0.0 0.05 0.10 0.15 0.20 0.25 0.30 0.35 0.40 0.45 0.50 0.55  
308778L  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Graco Standard Warranty  
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in  
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty  
published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by  
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written  
recommendations.  
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty  
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of  
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with  
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or  
maintenance of structures, accessories, equipment or materials not supplied by Graco.  
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of  
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned  
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will  
be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.  
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED  
TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.  
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy  
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or  
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.  
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT  
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to  
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these  
warranties.  
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or  
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the  
negligence of Graco, or otherwise.  
FOR GRACO CANADA CUSTOMERS  
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,  
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la  
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite  
de ou en rapport, directement ou indirectement, avec les procédures concernées.  
Graco Information  
TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.  
Phone: 612-623-6921 or Toll Free: 1-800-328-0211 Fax: 612-378-3505  
All written and visual data contained in this document reflects the latest product information available at the time of publication.  
Graco reserves the right to make changes at any time without notice.  
This manual contains English. MM 308778  
Graco Headquarters: Minneapolis  
International Offices: Belgium, China, Japan, Korea  
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441  
Copyright 1997, Graco Inc. is registered to I.S. EN ISO 9001  
Revised 11/2008  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   

Grizzly Drill G7947 User Manual
Haier Blender HB500BSS User Manual
Hasbro Games T Rex Jaw Chomping User Manual
Heat Glo LifeStyle Indoor Fireplace BAY 40 User Manual
Honeywell Network Cables Q7055A User Manual
HP Hewlett Packard Network Card HP RP7405 7410 User Manual
HP Hewlett Packard Stereo System 5614B User Manual
HP Hewlett Packard Switch 2520G POE User Manual
Hypertec Carrying Case 3507 User Manual
IBM Ricoh Scanner 2400 dpi User Manual