Owner’s Manual
Installation and Operation
Model:
XLR-N-CE
XLR-PB-CE
EC-87/09/058
NOTICE
DO NOT DISCARD THIS MANUAL
• Important operating
and maintenance
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
• Leave this manual with
party responsible for use
and operation.
WARNING
WARNING: If the information in these
instructions is not followed exactly, a fire
or explosion may result causing property
damage, personal injury, or death.
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
Hot glass will cause burns.
• DO NOT touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• DO NOT store or use gasoline or other flam-
mable vapors and liquids in the vicinity of this
or any other appliance.
• CAREFULLY SUPERVISE children in same room as
fireplace.
• Alert children and adults to hazards of high temperatures.
• What to do if you smell gas
- DO NOT try to light any appliance.
High temperatures may ignite clothing or other flammable
materials.
• Keep clothing, furniture, draperies and other flammable
materials away.
- DO NOT touch any electrical switch. DO
NOT use any phone in your building.
- Immediately call your gas supplier from a
neighbor’s phone. Follow the gas suppli-
er’s instructions.
This appliance has been supplied with an integral barrier
to prevent direct contact with the fixed glass panel. DO
NOT operate the appliance with the barrier removed.
- If you cannot reach your gas supplier, call
the fire department.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
• Installation and service must be performed
by a qualified installer, service agency, or the
gas supplier.
These instructions are only valid if the following country symbol is
on the appliance. If this symbol is not present on the appliance,
it is necessary to refer to the technical instructions which will
provide the necessary information concerning the modification
of the appliance to the conditions of use for the country.
This is a room sealed appliance and no other ventilation is
required than what is provided.
These instructions are valid for the following countries: GB, IE.
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Safety Alert Key:
• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.
• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
• NOTICE: Used to address practices not related to personal injury.
Table of Contents
A. Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
B. Limited Lifetime Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . 5
A. Vent Termination Minimum Clearances . . . . . . . . . . . . . . 21
7 Vent Information and Diagrams
1 Listing and Code Approvals
A. Approved Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
B. Vent Table Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
C. Use of Elbows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
D. Measuring Standards. . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
E. Vent Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
A. Appliance Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
A. Additional Related Standards. . . . . . . . . . . . . . . . . . . . . . . 7
B. Gas Pressure Requirements . . . . . . . . . . . . . . . . . . . . . . . 7
C. Non-Combustible Materials Specification. . . . . . . . . . . . . . 7
D. Combustible Materials Specification . . . . . . . . . . . . . . . . . 7
E. Electrical Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
8 Vent Clearances and Framing
A. Pipe Clearances to Combustibles . . . . . . . . . . . . . . . . . . 30
B. Wall Penetration Framing. . . . . . . . . . . . . . . . . . . . . . . . . 30
C. Install the Ceiling Firestop . . . . . . . . . . . . . . . . . . . . . . . . 31
D. Install Attic Insulation Shield. . . . . . . . . . . . . . . . . . . . . . . 32
User Guide
2 Operating Instructions
A. Gas Fireplace Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
B. Your Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
C. Clear Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
D. Decorative Doors and Fronts . . . . . . . . . . . . . . . . . . . . . . . 9
E. Decorative Media Options . . . . . . . . . . . . . . . . . . . . . . . . . 9
F. Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
G. Remote Controls, Wall Controls and Wall Switches. . . . . . 9
H. Before Lighting Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . . 9
I. Control Module Operation . . . . . . . . . . . . . . . . . . . . . . . . 10
J. Lighting Instructions (IPI) . . . . . . . . . . . . . . . . . . . . . . . . . 11
K. Battery Tray/Battery Installation . . . . . . . . . . . . . . . . . . . . 12
M. Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . 12
L. After Fireplace is Lit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
9 Appliance Preparation
A. Top Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
B. Securing and Leveling the Appliance. . . . . . . . . . . . . . . . 34
10 Installing Vent Pipe (SLP Pipe)
A. Assemble Vent Sections. . . . . . . . . . . . . . . . . . . . . . . . . . 35
B. Assemble Slip Sections . . . . . . . . . . . . . . . . . . . . . . . . . . 36
C. Secure The Vent Sections . . . . . . . . . . . . . . . . . . . . . . . . 36
D. Disassemble Vent Sections . . . . . . . . . . . . . . . . . . . . . . . 37
E. Install Decorative Ceiling Components . . . . . . . . . . . . . . 37
F. Install Metal Roof Flashing. . . . . . . . . . . . . . . . . . . . . . . . 38
G. Assemble and Install Storm Collar. . . . . . . . . . . . . . . . . . 38
H. Install Vertical Termination Cap . . . . . . . . . . . . . . . . . . . . 39
I. Install Decorative Wall Components . . . . . . . . . . . . . . . . 39
J. Heat Shield Requirements for Horizontal Termination . . . 39
K. Install Horizontal Termination Cap . . . . . . . . . . . . . . . . . . 40
3 Maintenance and Service
A. Maintenance Tasks-Homeowner . . . . . . . . . . . . . . . . . . . 13
B. Maintenance Tasks-Qualified Service Technician . . . . . . 14
Installer Guide
11 Gas Information
A. Gas Pressure Requirements . . . . . . . . . . . . . . . . . . . . . . 41
B. Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
C. Access Through the Valve Assembly . . . . . . . . . . . . . . . . 41
4 Getting Started
A. Typical Appliance System. . . . . . . . . . . . . . . . . . . . . . . . . 15
B. Design and Installation Considerations . . . . . . . . . . . . . . 16
C. Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . . . 16
D. Inspect Appliance and Components. . . . . . . . . . . . . . . . . 16
12 Electrical Information
A. Wiring Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
B. IntelliFire Plus™ Ignition System Wiring . . . . . . . . . . . . . 42
C. Optional Accessories Requirements . . . . . . . . . . . . . . . . 42
D. Electrical Service and Repair. . . . . . . . . . . . . . . . . . . . . . 43
E. Junction Cord Information . . . . . . . . . . . . . . . . . . . . . . . . 43
F. Blower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
5 Framing and Clearances
A. Selecting Appliance Location . . . . . . . . . . . . . . . . . . . . . . 17
B. Constructing the Appliance Chase. . . . . . . . . . . . . . . . . . 18
C. Clearances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
D. Mantel and Wall Projections. . . . . . . . . . . . . . . . . . . . . . . 20
13 Finishing
6 Termination Locations
A. Framing and Finishing Instructions . . . . . . . . . . . . . . . . . 44
B. Mantel and Wall Projections. . . . . . . . . . . . . . . . . . . . . . . 47
C. Facing Material. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
3
D. Decorative Fronts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
14 Appliance Setup
A. Remove Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . 50
B. Remove the Shipping Materials . . . . . . . . . . . . . . . . . . . . 50
C. Clean the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
D. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
E. Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
F. Install the Mesh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
G. Air Shutter Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
H. Media Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
15 Troubleshooting
A. IntelliFire Plus™ Ignition System . . . . . . . . . . . . . . . . . . . 52
16 Component Access
A. Decorative Front and Fixed Glass Assembly Removal . . 54
B. Valve Pressure Taps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
C. Control Module Access. . . . . . . . . . . . . . . . . . . . . . . . . . . 54
D. Media Tray Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
E. Burner and Base Pan Removal . . . . . . . . . . . . . . . . . . . . 54
F. Access Through the Valve Assembly . . . . . . . . . . . . . . . . 55
G. Gas Valve Replacement. . . . . . . . . . . . . . . . . . . . . . . . . . 56
H. Pilot Assembly Replacement . . . . . . . . . . . . . . . . . . . . . . 56
17 Reference Materials
A. Appliance Dimension Diagram. . . . . . . . . . . . . . . . . . . . . 57
B. Vent Components Diagrams . . . . . . . . . . . . . . . . . . . . . . 58
C. Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
D. Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
= Contains updated information.
4
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Limited Lifetime Warranty
Hearth & Home Technologies Inc.
LIMITED LIFETIME WARRANTY
Hearth & Home Technologies Inc., on behalf of its hearth brands (”HHT”), extends the following warranty for
HHT gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer.
WARRANTY COVERAGE:
HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking ownership
of the appliance at the site of installation within two years following the date of original purchase, that the HHT appliance
will be free from defects in materials and workmanship at the time of manufacture. After installation, if covered compo-
nents manufactured by HHT are found to be defective in materials or workmanship during the applicable warranty period,
HHT will, at its option, repair or replace the covered components. HHT, at its own discretion, may fully discharge all of its
obligations under such warranties by replacing the product itself or refunding the verified purchase price of the product
itself. The maximum amount recoverable under this warranty is limited to the purchase price of the product. This warranty
is subject to conditions, exclusions and limitations as described below.
WARRANTY PERIOD:
Warranty coverage begins on the date of original purchase. In the case of new home construction, warranty coverage
begins on the date of first occupancy of the dwelling or six months after the sale of the product by an independent,
authorized HHT dealer/ distributor, whichever occurs earlier. The warranty shall commence no later than 24 months
following the date of product shipment from HHT, regardless of the installation or occupancy date. The warranty period for
parts and labor for covered components is produced in the following table.
The term “Limited Lifetime” in the table below is defined as: 20 years from the beginning date of warranty coverage for
gas appliances, and 10 years from the beginning date of warranty coverage for wood, pellet, and coal appliances. These
time periods reflect the minimum expected useful lives of the designated components under normal operating conditions.
Warranty Period
Parts Labor
HHT Manufactured Appliances and Venting
EPA
Components Covered
Gas
X
Wood Pellet
Coal Electric Venting
Wood
All parts and material except as
covered by Conditions,
Exclusions, and Limitations
listed
1 Year
X
X
X
X
X
X
Igniters, electronic components,
and glass
X
X
X
X
X
X
2 years
X
X
X
Factory-installed blowers
Molded refractory panels
3 years
X
X
Firepots and burnpots
Castings and baffles
5 years 1 year
X
X
Manifold tubes,
HHT chimney and termination
7 years 3 years
X
X
10
1 year
years
X
X
X
Burners, logs and refractory
Firebox and heat exchanger
Limited
3 years
Lifetime
X
X
X
X
X
X
X
X
All replacement parts
beyond warranty period
90 Days
X
X
See conditions, exclusions, and limitations on next page.
4021-645C 12-29-10
Page 1 of 2
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
5
B. Limited Lifetime Warranty (continued)
WARRANTY CONDITIONS:
•
This warranty only covers HHT appliances that are purchased through an HHT authorized dealer or distributor. A list of
HHT authorized dealers is available on the HHT branded websites.
•
•
This warranty is only valid while the HHT appliance remains at the site of original installation.
Contact your installing dealer for warranty service. If the installing dealer is unable to provide necessary parts, contact
the nearest HHT authorized dealer or supplier. Additional service fees may apply if you are seeking warranty service
from a dealer other than the dealer from whom you originally purchased the product.
•
Check with your dealer in advance for any costs to you when arranging a warranty call. Travel and shipping charges
for parts are not covered by this warranty.
WARRANTY EXCLUSIONS:
This warranty does not cover the following:
•
•
•
Changes in surface finishes as a result of normal use. As a heating appliance, some changes in color of interior and
exterior surface finishes may occur. This is not a flaw and is not covered under warranty.
Damage to printed, plated, or enameled surfaces caused by fingerprints, accidents, misuse, scratches, melted items,
or other external sources and residues left on the plated surfaces from the use of abrasive cleaners or polishes.
Repair or replacement of parts that are subject to normal wear and tear during the warranty period. These parts
include: paint, wood, pellet and coal gaskets, firebricks, grates, flame guides, light bulbs, batteries and the discolor-
ation of glass.
•
•
Minor expansion, contraction, or movement of certain parts causing noise. These conditions are normal and com-
plaints related to this noise are not covered by this warranty.
Damages resulting from: (1) failure to install, operate, or maintain the appliance in accordance with the installation
instructions, operating instructions, and listing agent identification label furnished with the appliance; (2) failure to
install the appliance in accordance with local building codes; (3) shipping or improper handling; (4) improper opera-
tion, abuse, misuse, continued operation with damaged, corroded or failed components, accident, or improperly/
incorrectly performed repairs; (5) environmental conditions, inadequate ventilation, negative pressure, or drafting
caused by tightly sealed constructions, insufficient make-up air supply, or handling devices such as exhaust fans or
forced air furnaces or other such causes; (6) use of fuels other than those specified in the operating instructions; (7)
installation or use of components not supplied with the appliance or any other components not expressly authorized
and approved by HHT; (8) modification of the appliance not expressly authorized and approved by HHT in writing;
and/or (9) interruptions or fluctuations of electrical power supply to the appliance.
•
•
•
Non-HHT venting components, hearth components or other accessories used in conjunction with the appliance.
Any part of a pre-existing fireplace system in which an insert or a decorative gas appliance is installed.
HHT’s obligation under this warranty does not extend to the appliance’s capability to heat the desired space. Informa-
tion is provided to assist the consumer and the dealer in selecting the proper appliance for the application. Consider-
ation must be given to appliance location and configuration, environmental conditions, insulation and air tightness of
the structure.
This warranty is void if:
•
The appliance has been over-fired or operated in atmospheres contaminated by chlorine, fluorine, or other damaging
chemicals. Over-firing can be identified by, but not limited to, warped plates or tubes, rust colored cast iron, bubbling,
cracking and discoloration of steel or enamel finishes.
•
•
The appliance is subjected to prolonged periods of dampness or condensation.
There is any damage to the appliance or other components due to water or weather damage which is the result of, but
not limited to, improper chimney or venting installation.
LIMITATIONS OF LIABILITY:
•
The owner’s exclusive remedy and HHT’s sole obligation under this warranty, under any other warranty, express or
implied, or in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specified above. In no
event will HHT be liable for any incidental or consequential damages caused by defects in the appliance. Some states
do not allow exclusions or limitation of incidental or consequential damages, so these limitations may not apply to you.
This warranty gives you specific rights; you may also have other rights, which vary from state to state. EXCEPT TO
THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY
SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE
EXPRESSED WARRANTY SPECIFIED ABOVE.
4021-645C 12-29-10
Page 2 of 2
6
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
Listing and Code Approvals
1
The fireplace and its individual shut-off valve must be dis-
connected from the gas supply piping system during any
pressure testing of the system at test pressures in excess
of 60 mbar.
A. Appliance Certification
MODELS: XLR-N-CE, XLR-PB-CE
LABORATORY: GL Industries Ltd.
TYPE: Gas Fireplace
If the fireplace must be isolated from the gas supply pip-
ing system by closing an individual shut-off valve, it must
be of the handle-less type.
STANDARD: Latest version of BS EN 613: 2001
DIRECTIVE: GAD90/396/EEC
C. Non-Combustible Materials Specification
Material which will not ignite and burn. Such materials are
those consisting entirely of steel, iron, brick, tile, concrete,
slate, glass or plasters, or any combination thereof.
A. Additional Related Standards
The installation must comply with these installation instruc-
tions and all relevant parts of Local and National Building
Standards Regulations and those relevant recommenda-
tions of the following British Standards. BS 5871: Part 1
BS 8303 BS 5440: Parts 1 & 2 BS 6891 BSEN1856 Parts
1 & 2 BS 5482 Part 1, as well as IGE/UP/7.
Materials that are reported as passing ASTM E 136,
Standard Test Method for Behavior of Materials in a
Vertical Tube Furnace at 750 ºC and UL763 shall be
considered non-combustible materials.
D. Combustible Materials Specification
NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.
This appliance is tested and approved as either supplemen-
tal room heat or as a decorative appliance. It should not be
factored as primary heat in residential heating calculations.
Materials made of or surfaced with wood, compressed pa-
per, plant fibers, plastics, or other material that can ignite
and burn, whether flame proofed or not, or plastered or
unplastered shall be considered combustible materials.
The Heat & Glo gas appliances discussed in this Installer’s
Guide have been tested to certification standards and listed
by the applicable laboratories.
E. Electrical Codes
All electrical safety testing has been done following the EN
60335-2-102 standard. Local codes apply.
This appliance must be installed in accordance with the
rules in force.
NOX Class 5 for G20, NOX Class 5 for G31
B. Gas Pressure Requirements
Pressure requirements for XLR fireplaces are shown in
table below.
Two taps are provided on the right hand side of the gas
control for a test gauge connection to measure the inlet
and outlet pressures.
Natural Gas
(G20)
Propane
(G31)
Propane
(G31)
Butane
(G30)
Butane
(G30)
Natural Gas
(G25)
CAT
I2H, I2E, I2E+
20 mbar
8.7 mbar
I3P
I3P
I3B/P
I3B/P
I2E+
Inlet Pressure
Burner Pressure
Gas Rate
37 mbar
25 mbar
.134 m3
50 mbar
25 mbar
.134 m3
30 mbar
25 mbar
.111 m3
50 mbar
25 mbar
.111 m3
25 mbar
8.7 mbar
.40 m3
/
h
.405 m3
/
/
/
/
/
h
h
h
h
h
Heat Input (Net)
7.32 kW
DMS 42
51
6.74 kW
DMS .057
30
6.74 kW
DMS .057
30
6.44 kW
DMS 55
30
6.44 kW
DMS 55
30
7.32 kW
DMS 42
51
Burner Injector
Pilot Injector
Columns highlighted in gray = The gas control valve supplied with this product is approved for a maximum
inlet pressure of 37 mbar. For pressures over 37 mbar, an in line pressure regulator must be installed
upstream from the gas control valve.
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
7
User Guide
Operating Instructions
2
If you expect that small children or vulnerable adults may
come into contact with this fireplace, the following precau-
tions are recommended:
A. Gas Fireplace Safety
WARNING
• Install a physical barrier such as:
- A decorative firescreen.
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
- Adjustable safety gate.
Hot glass will cause burns.
• DO NOT touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• Install a switch lock or a wall/remote control with child
protection lockout feature.
• Keep remote controls out of reach of children.
• CAREFULLY SUPERVISE children in same room as
fireplace.
• Alert children and adults to hazards of high temperatures.
• Never leave children alone near a hot fireplace, whether
operating or cooling down.
• Teach children to NEVER touch the fireplace.
High temperatures may ignite clothing or other
flammable materials.
• Keep clothing, furniture, draperies and other flammable
materials away.
• Consider not using the fireplace when children will be
present.
To prevent unintended operation when not using your fire-
place for an extended period of time (summer months,
vacations, trips, etc):
This appliance has been supplied with an integral barrier
to prevent direct contact with the fixed glass panel. DO
NOT operate the appliance with the barrier removed.
• Remove batteries from remote controls.
• Turn off wall controls.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
• Unplug 6 volt adapter plug and remove batteries on IPI
models.
WARNING! Choking Hazard! Keep glass rock media
out of reach of children.
B. Your Fireplace
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capa-
bilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use
of the appliance by a person responsible for their safety.
WARNING! DO NOT operate fireplace before read-
ing and understanding operating instructions. Failure
to operate fireplace according to operating instructions
could cause fire or injury.
Children should be supervised to ensure that they do not
play with the appliance.
DECORATIVE DOORS
SECTION 2.D.
RC100
(OPTIONAL
REMOTE CONTROL)
SECTION 2.G
FIXED GLASS ASSEMBLY
(NOT SHOWN)
SECTION 14.E.
CLEAR SPACE
SECTION 2.C.
MEDIA OPTIONS
SECTION 2.E
MEDIA - BLACK, CLEAR, AMBER, COLBALT
MEDIA - BK2 - GEMS, MEDIA WH2-GEMS
MEDIA-STONES-2
XLR-LOGS
Figure 2.1 General Operating Parts
8
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
C. Clear Space
F. Fixed Glass Assembly
WARNING! DO NOT place combustible objects in front
of the fireplace or block louvers. High temperatures may
start a fire. See Figure 2.2.
See Section 14.E.
G. Remote Controls, Wall Controls and Wall
Switches
Avoid placing candles and other heat-sensitive objects on
mantel or hearth. Heat may damage these objects.
Follow the instructions supplied with the control installed
to operate your fireplace:
For safety:
• Install a switch lock or a wall/remote control with child
protection lockout feature.
• Keep remote controls out of reach of children.
See your dealer if you have questions.
H. Before Lighting Fireplace
Before operating this fireplace for the first time, have a
qualified service technician:
• Verify all shipping materials have been removed from
inside and/or underneath the firebox.
• Verify that rock media tray is securely fastened to the
base pan.
• Check the wiring.
• Check the air shutter adjustment.
• Ensure that there are no gas leaks.
Figure 2.2 Clear Space
• Ensure that the glass is sealed and in the proper position
and that the integral barrier is in place.
D. Decorative Doors and Fronts
WARNING! Risk of Fire or Asphyxiation! DO NOT op-
erate fireplace with fixed glass assembly removed.
WARNING! Risk of Fire! Install ONLY doors or fronts
approved by Hearth & Home Technologies. Unapproved
doors or fronts may cause fireplace to overheat.
This decorative front has been supplied with an
integral barrier to prevent direct contact with the fixed
glass panel. DO NOT operate the fireplace with the
barrier removed.
Contact your dealer or Hearth & Home Technologies if
the barrier is not present or help is needed to properly
install one.
For more information refer to the instructions supplied with
your decorative door or front.
E. Decorative Media Options
This appliance ships standard without a decorative media
option. For installation and removal of these decorative
media options, refer to installation instructions which ship
with the media options.
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
9
5. Module Reset Switch
I. Control Module Operation
1. The control module has an ON/OFF/REMOTE selector
switch that must be set. See Figure 2.3.
This module may lock-out under certain conditions.
When this occurs, the appliance will not ignite or
respond to commands. The module will go into lock-out
mode by emitting three audible beeps, then continuously
displaying an error code at its status indicator LED.
OFF Position: Appliance will ignore all power inputs and
will not respond to any commands from a wall switch or
optional remote. The unit should be in the OFF position
during installation, service, battery installation, , fuel
conversion, and in the event that the control goes into
LOCK-OUT mode as a result of an error code.
•
Check battery tray. Remove batteries if installed.
Batteries should only be installed for use during power
outages. See Section H.
ON Position: Appliance will ignite and run continuously
in the HI flame setting, with no adjustment in flame
output. This mode of operation is primarily used for
initial installation or power outage operation with battery
backup.
•
•
•
Locate the module reset switch. See Figure 2.4 or 2.5.
Set the module reset switch to the RESET position.
Wait five (5) minutes to allow possible accumulated gas
to clear.
•
•
Set the module reset switch to ON.
Start the appliance.
REMOTE Position: Appliance will initiate commands
from a wired wall switch and/or one of the optional
wireless remote options.
WARNING! Risk of Explosion! DO NOT press the mod-
ule reset switch more than one time within a five minute
time period. Gas may accumulate in firebox. Call a quali-
fied service technician.
2. A wall switch can be wired into the control module brown
and red wires. See Figure 12.1.
3. The control module has safety feature that automatically
shuts down the fireplace after 9 hours of continuous
operation without receiving a command from the wall
switch or optional remote.
4. If you intend to use both a wired wall switch and an optional
remote control to operate your fireplace, the wall switch
will override any commands given by the remote.
MODULE RESET
SWITCH
MODULE
SELECTOR
SWITCH
Figure 2.4 Location of Module Reset Switch - Tonic Front
MODULE RESET
SWITCH
FLAME HI/LOW
SWITCH
STATUS
INDICATOR LED
NG/LP GAS-TYPE
SELECTOR SWITCH
Figure 2.3 Control Module
Note: The HI/LO and LP/NG switches on the control module
are non-functional on the XLR fireplace.
Nine Hour Safety Shutdown Feature
This appliance has a safety feature that automatically
shuts down the fireplace after nine hours of continuous
operation with receiving a command from the wall
switch or optional remote.
Figure 2.5 Location of Module Reset Switch - Martini Front
10
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
J. Lighting Instructions (IPI)
The IPI system may be operated with two D-cell batteries. When using batteries, unplug the transformer. To prolong battery
life, remove them when using the transformer.
FOR YOUR SAFETY
LIGHTING
READ BEFORE LIGHTING
INSTRUCTIONS (IPI)
WARNING: If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
1. This appliance is equipped with an ignition
device which automatically lights the burner.
DO NOT try to light the burner by hand.
• Immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions.
A. This appliance is equipped with an
intermittent pilot ignition (IPI) device
which automatically lights the burn-
er. DO NOT try to light the burner by
hand.
GAS
VALVE
• If you cannot reach your gas sup-
plier, call the fire department.
B. BEFORE LIGHTING, smell all around
the appliance area for gas. Be sure to
smell next to the floor because some
gas is heavier than air and will settle
on the floor.
C. DO NOT use this appliance if any
part has been under water. Imme-
diately call a qualified service tech-
nician to inspect the appliance and
to replace any part of the control
system and any gas control which
has been under water.
2. Wait five (5) minutes to clear out any gas.
Then smell for gas, including near the floor. If
you smell gas, STOP! Follow “B” in the Safety
Information located on the left side of this la-
bel. If you do not smell gas, go to next step.
WHAT TO DO IF YOU SMELL GAS
• DO NOT try to light any appliance.
3. To light the burner:
• DO NOT touch any electric switch; do
not use any phone in your building.
Equipped with wall switch: Turn ON/OFF switch
to ON.
Equipped with remote or wall control: Press
ON or FLAME button.
WARNING: CAUTION:
Equipped with thermostat: Set temperature to
desired setting.
Hot while in operation. DO NOT touch.
Keep children, clothing, furniture, gaso-
line and other liquids having flammable
vapors away.
DO NOT CONNECT LINE VOLT-
AGE (110/120 VAC OR 220/240
VAC) TO THE CONTROL VALVE.
4. If the appliance does not light after three tries,
call your service technician or gas supplier.
Improper installation, adjustment, al-
teration, service or maintenance can
cause injury or property damage. Re-
fer to the owner’s information manual
provided with this appliance.
TO TURN OFF
GAS TO APPLIANCE
1. Equipped with wall switch: Turn ON/OFF switch
DO NOT operate the appliance with
fixed glass assembly removed, cracked
or broken. Replacement of the fixed
glass assembly should be done by a
licensed or qualified service person.
to OFF.
This appliance needs fresh air for
safe operation and must be installed
so there are provisions for adequate
combustion and ventilation air.
Equipped with remote or wall control: Press
OFF button.
NOT FOR USE
WITH SOLID FUEL
Equipped with thermostat: Set temperature to
lowest setting.
If not installed, operated, and main- For use with natural gas and propane.
tained in accordance with the manufac- A conversion kit, as supplied by the
turer’s instructions, this product could manufacturer, shall be used to convert
expose you to substances in fuel or this appliance to the alternate fuel.
2. Service technician should turn off electric
power to the control when performing service.
fuel combustion which are known to the
State of California to cause cancer, birth
Also Certified for Installation in a
Bedroom or a Bedsitting Room.
593-913G
defects, or other reproductive harm.
For assistance or additional informa-
Keep burner and control compartment
tion, consult a qualified installer, ser-
clean. See installation and operating
vice agency or the gas supplier.
instructions accompanying appliance.
For additional information on operating your
Final inspection by
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
11
K. Battery Tray/Battery Installation
L. After Fireplace is Lit
The IntelliFire PlusTM system has a battery backup option.
Battery longevity and performance will be affected by the
service temperatures of this appliance. Batteries should
only be used as a power source in the event of an emer-
gency such as an outage.
Initial Break-in Procedure
• The fireplace should be run three to four hours
continuously on high.
• Turn the fireplace off and allow it to completely cool.
• Remove fixed glass assembly. See Section 14.E.
• Clean fixed glass assembly. See Section 3.
• Replace the fixed glass assembly and run continuously
on high an additional 12 hours.
This cures the materials used to manufacture the fire-
place.
NOTICE! Open windows for air circulation during fire-
place break-in.
• Some people may be sensitive to smoke and odors.
• Smoke detectors may activate.
M. Frequently Asked Questions
ISSUE
SOLUTIONS
This is a result of gas combustion and temperature variations. As the fireplace warms, this con-
densation will disappear.
Condensation on the glass
Blue flames
This is a result of normal operation and the flames will begin to yellow as the fireplace is allowed
to burn for 20 to 40 minutes.
When first operated, this fireplace may release an odor for the first several hours. This is caused
by the curing of materials from manufacturing. Odor may also be released from finishing materials
and adhesives used near the fireplace. These circumstances may require additional curing related
to the installation environment.
Odor from fireplace
Film on the glass
This is a normal result of the curing process of the paint. Glass should be cleaned within 3 to 4
hours of initial burning. A non-abrasive cleaner such as gas appliance glass cleaner may be neces-
sary. See your dealer.
Noise is caused by metal expanding and contracting as it heats up and cools down, similar to the
sound produced by a furnace or heating duct. This noise does not affect the operation or longevity
of the fireplace.
Metallic noise
This appliance can operated on battery power in the event of a power outage. To access the bat-
Power Outages (battery backup) tery pack, the decorative front, mesh and glass assembly must be removed. Refer to Section 12
for more details.
Wall above appliance feels hot to No action necessary. This appliance ships with a non-combustible material attached. Specifica-
the touch.
tions of the attached non-combustible material are listed in Section 1.E.
12
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Service
3
Decorative Doors
Any safety screen or guard removed for servicing must be
replaced prior to operating the fireplace.
Frequency: Annually
By: Homeowner
When properly maintained, your fireplace will give you
many years of trouble-free service. We recommend an-
nual service by a qualified service technician.
Tools needed: Protective gloves, stable work surface
• Refer to the installation instructions which ship with the
decorative door.
All parts listed in this manual may be ordered from an au-
thorized dealer. A list of available service parts is located in
Section 16.C of this manual and in the installation instruc-
tions included in decorative media.
• Assess condition of screen and replace as necessary.
• Inspect for scratches, dents or other damage and repair
as necessary.
• Check that louvers are not blocked.
• Vacuum and dust surfaces.
A. Maintenance Tasks-Homeowner
Installation and repair should be done by a qualified service
technician only. The fireplace should be inspected before
use and at least annually by a professional service person.
Venting
Frequency: Seasonally
By: Homeowner
The following tasks may be performed annually by the
homeowner. If you are uncomfortable performing any of
the listed tasks, please call your dealer for a service ap-
pointment.
Tools needed: Protective gloves and safety glasses.
• Inspect venting and termination cap for blockage or
obstruction such plants, bird nests, leaves, snow, debris,
etc.
CAUTION! Risk of Burns! The fireplace should be turned
off and cooled before servicing.
• Verify termination cap clearance to subsequent construc-
tion (building additions, decks, fences, or sheds). See
Section 6.
Glass Cleaning
Frequency: Seasonally
By: Homeowner
• Inspect for corrosion or separation.
Tools Needed: Protective gloves, glass cleaner, drop
cloth and a stable work surface.
• Verify weather stripping, sealing and flashing remains
intact.
CAUTION! Handle fixed glass assembly with care.
Glass is breakable.
• Inspect draft shield to verify it is not damaged or missing.
• Avoid striking, scratching or slamming glass
• Avoid abrasive cleaners
• DO NOT clean glass while it is hot
Decorative Media Options
Frequency: Maintenance is not required
By: Homeowner
• Prepare a work area large enough to accommodate fixed
glass assembly and door frame by placing a drop cloth
on a flat, stable surface.
Tools needed: Protective gloves and safety glasses.
• The decorative media options DO NOT require routine
maintenance if they are properly installed. Refer to the
installation instructions which ship the decorative media
to verify correct installation.
Note: Fixed glass assembly and gasketing may have res-
idue that can stain carpeting or floor surfaces.
• Remove door or decorative front from fireplace and set
aside on work surface.
• See Section 14.E for instructions to remove fixed glass
assembly.
• Clean glass with a non-abrasive commercially available
cleaner.
- Light deposits: Use a soft cloth with soap and water
- Heavy deposits: Use commercial fireplace glass
cleaner (consult with your dealer)
• Reinstall door or decorative front.
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
13
• Gas pressure taps are accessible by removing the deco-
rative front and fixed glass assembly. Refer to Section
11.A for information related to the gas valve and gas
pressure settings.
B. Maintenance Tasks-Qualified Service
Technician
To prevent inadvertent burner operation while servicing
this appliance:
Burner Ignition and Operation
Frequency: Annually
• Unplug DC regulator from junction cord.
• Remove batteries from battery pack (if installed).
• Shut off gas supply to the appliance.
By: Qualified Service Technician
Tools needed: Protective gloves, vacuum cleaner, whisk
broom, flashlight, voltmeter, indexed drill bit set, and a
manometer.
The following tasks must be performed by a qualified ser-
vice technician.
Gasket Seal and Glass Assembly Inspection
Frequency: Annually
• Verify burner is properly secured and aligned with pilot
or igniter.
• Clean off burner top, inspect for plugged ports, corrosion
or deterioration. Replace burner if necessary.
By: Qualified Service Technician
Tools needed: Protective gloves, drop cloth and a stable
• Verify batteries have been removed from battery back-
up IPI systems to prevent premature battery failure or
leaking.
work surface.
• Inspect gasket seal and its condition.
• Inspect fixed glass assembly for scratches and nicks that
can lead to breakage when exposed to heat.
• Check for smooth lighting and ignition carryover to all
ports. Verify that there is no ignition delay.
• Confirm there is no damage to glass or glass frame.
Replace as necessary.
• Inspect for lifting or other flame problems.
• Verify air shutter setting is correct. See Section 14.G for
required air shutter setting. Verify air shutter is clear of
dust and debris.
• Verify that fixed glass assembly is properly retained and
attachment components are intact and not damaged.
Replace as necessary.
• Inspect orifice for soot, dirt and corrosion. Verify orifice
size is correct. See Service Parts List for proper orifice
sizing.
Firebox
Frequency: Annually
By: Qualified Service Technician
• Verify manifold and inlet pressures. Adjust regulator as
required.
Tools needed: Protective gloves, sandpaper, steel wool,
• Inspect pilot flame pattern and strength. See Figure 3.1
for proper pilot flame pattern. Clean or replace orifice
spud as necessary.
cloths, mineral spirits, primer and touch-up paint.
• Inspect for paint condition, warped surfaces, corrosion
or perforation. Sand and repaint as necessary.
• Inspect IPI flame sensing rod for soot, corrosion and
deterioration. Polish with fine steel wool or replace as
required.
• Replace fireplace if firebox has been perforated.
Control Compartment and Firebox Top
Frequency: Annually
• Verify IPI millivolt output. Replace as necessary.
By: Qualified Service Technician
• Verify that there is not a short in flame sense circuit
by checking continuity between pilot hood and flame
sensing rod. Replace pilot as necessary.
Tools needed: Protective gloves, vacuum cleaner, dust
cloths
• Vacuum and wipe out dust, cobwebs, debris or pet hair.
Use caution when cleaning these areas. Screw tips that
have penetrated the sheet metal are sharp and should
be avoided.
• Remove all foreign objects.
• Verify unobstructed air circulation.
Gas Pressure Information
Frequency: Upon initial installation and gas valve re-
placement or service.
By: Qualified Service Technician
Tools needed: Protective gloves, manometer, flashlight,
screw driver set.
Figure 3.1 IPI Pilot Flame Pattern
14
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
Installer Guide
Getting Started
4
A. Typical Appliance System
NOTICE: Illustrations and photos reflect typical installations and are for design purposes only. Illustrations/diagrams are not
drawn to scale. Actual product may vary from pictures in manual
HORIZONTAL
TERMINATION CAP
(SECTION 10.K)
VERTICAL TERMINATION CAP
(SECTION 10.H)
WALL PENETRATION
FRAMING (SECTION 8.B)
NON-COMBUSTIBLE ROOF
FLASHING MAINTAINS MINIMUM
CLEARANCE AROUND PIPE
(SECTION 10.F)
STORM COLLAR
(SECTION 10.G)
VENT PIPE PENETRATES
ROOF PREFERABLY
WITHOUT AFFECTING
ROOF RAFTERS
(SECTION 8.C)
ATTIC INSULATION
SHIELD (NOT SHOWN)
MUST BE USED HERE
TO KEEP INSULATION
AWAY FROM VENT PIPE
IF ATTIC IS INSULATED.
(SECTION 8.D)
VENT PIPE
(SECTIONS 7 and 8)
CEILING FIRESTOP
ON FLOOR OF ATTIC
(SECTION 8.C)
FRAMING HEADED
OFF IN CEILING
JOISTS (SECTION 8.C)
FRAMING/HEADER
(SECTION 5)
WALL SWITCH
GAS LINE
(SECTION 11)
Figure 4.1 Typical System
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
15
B. Design and Installation Considerations
D. Inspect Appliance and Components
Heat & Glo direct vent gas appliances are designed to
operate with all combustion air siphoned from outside of
the building and all exhaust gases expelled to the outside.
No additional outside air source is required.
• Carefully remove the appliance and components from
the packaging.
• The vent system components and decorative doors and
fronts may be shipped in separate packages.
Before installing, determine the following:
• Where the appliance is to be installed.
• The vent system configuration to be used.
• Gas supply piping.
• Report to your dealer any parts damaged in shipment,
particularly the condition of the glass.
• Read all of the instructions before starting the instal-
lation. Follow these instructions carefully during the
installation to ensure maximum safety and benefit.
• Electrical wiring requirements.
• Framing and finishing details.
WARNING! Risk of Fire or Explosion! Damaged parts
could impair safe operation. DO NOT install damaged, in-
complete or substitute components. Keep appliance dry.
• Whether optional accessories—devices such as a wall
switch or remote control—are desired.
Hearth & Home Technologies disclaims any responsibility for,
and the warranty will be voided by, the following actions:
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage. For
assistance or additional information, consult a qualified
service technician, service agency or your dealer.
• Installation and use of any damaged appliance or vent
system component.
• Modification of the appliance or vent system.
• Installation other than as instructed by Hearth & Home
Technologies.
C. Tools and Supplies Needed
Before beginning the installation be sure that the following
tools and building supplies are available.
• Improper positioning of the gas logs or the glass door.
• Installation and/or use of any component part not approved
by Hearth & Home Technologies.
Tape measure
Pliers
Framing material
Hammer
Any such action may cause a fire hazard.
Phillips screwdriver Manometer
Gloves
Framing square
Voltmeter
Electric drill and bits (1/4 in.)
Safety glasses
WARNING! Risk of Fire, Explosion or Electric Shock!
DO NOT use this appliance if any part has been under
water. Call a qualified service technician to inspect the
appliance and to replace any part of the control system
and/or gas control which has been under water.
Plumb line
Level
Reciprocating saw
Flat blade screwdriver
Non-corrosive leak check solution
1/2 - 3/4 in. length, #6 or #8 Self-drilling screws
Caulking material (150 ºC minimum continuous exposure
rating)
One 1/4 in. female connection (for optional fan).
16
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
Framing and Clearances
5
A. Selecting Appliance Location
When selecting a location for the appliance it is important to
consider the required clearances to walls (see Figure 5.1).
WARNING! Risk of Fire or Burns! Provide adequate
clearance around air openings and for service access.
Due to high temperatures, the appliance should be locat-
ed out of traffic and away from furniture and draperies.
NOTICE: Illustrations reflect typical installations and are
FOR DESIGN PURPOSES ONLY. Illustrations/diagrams
are not drawn to scale. Actual installation may vary due to
individual design preference.
A
E
2,54 cm
D*
ALCOVE
INSTALLATION
A
B
C
TOP VENT
ONE 90º ELBOW
TOP VENT
ONE 90° ELBOW
B
F
A
B
C
D*
E
F
See Section D.
Figure 5.6
Centimeters
135
122
191
49
45
Figure 5.1 Appliance Locations
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
17
B. Constructing the Appliance Chase
A chase is a vertical box-like structure built to enclose the
gas appliance and/or its vent system. In cooler climates
the vent should enclosed inside the chase.
NOTICE: Treatment of ceiling firestops and wall shield
firestops and construction of the chase may vary with the
type of building. These instructions are not substitutes
for the requirements of local building codes. Therefore,
you MUST check local building codes to determine the
requirements to these steps.
Chases should be constructed in the manner of all out-
side walls of the home to prevent cold air drafting prob-
lems. The chase should not break the outside building
envelope in any manner.
The factory-supplied non-combustible board must be
used in all installations. It must be directly attached to
structural framing adjacent to the appliance. Screw fas-
teners should be installed in the pilot holes provided in
the outer perimeter of the non-combustible board. See
Figure 13.3.
The factory-supplied board is designed such that its edg-
es will be at the approximate center of the adjacent fram-
ing, assuming it is 3,8 nominal thickness. This will allow
the wallboard joints to occur on the center of the framing
where the panels can be fastened properly. If the framing
thickness is less than 3,8 nominal, such as with formed
steel systems, then it may be necessary to adjust the ad-
jacent framing dimensions so that the non-combustible
board and wallboard joints are centered on the framing.
18
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
C. Clearances
NOTICE: Install appliance on hard metal or wood surfaces
extending full width and depth. DO NOT install directly
on carpeting, vinyl, tile or any combustible material other
than wood.
WARNING! Risk of Fire! Maintain specified air space
clearances to appliance and vent pipe:
• Insulation and other materials must be secured to prevent
accidental contact.
• The chase must be properly blocked to prevent blown
insulation or other combustibles from entering and
making contact with fireplace or chimney.
• Failure to maintain airspace may cause overheating and
a fire.
Note: Figure 5.2 shows the fireplace installed on the
floor. However, this fireplace can be elevated off the floor
provided that the fireplace is properly supported by framing
materials and the ceiling clearances are maintained.
MEASURE FROM TOP OF
FIREPLACE OPENING
A
E
F
B
H
J
C
G
D
I
MINIMUM FRAMING DIMENSIONS*
A
B
C
D
E
F
G
H
I
J
Rough
Opening
(Vent Pipe)
Rough
Opening
(Height)
Rough
Opening
(Depth)
Rough
Opening
(Width)
Clearance
to Ceiling
Combustible
Floor
Combustible
Flooring
Behind
Sides of
Front of
Appliance Appliance Appliance
22
107
46
127
79
0
0
3
3
91
Centimeters
Figure 5.2 Clearances to Combustibles
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
19
D. Mantel and Wall Projections
WARNING! Risk of Fire! Comply with all minimum clear-
ances to combustibles as specified. Framing or finishing
material closer than the minimums listed must be construct-
ed entirely of noncombustible materials (i.e., steel studs,
concrete board, etc).
2,5 cm
FRAMING
Mantels (Combustible/Non-Combustible)
1,3 cm
Thick Wall
Sheathing
30 cm
MAX.
MEASUREMENT
FROM TOP OF
FIREPLACE
OPENING
36 cm
MIN.
NAILING TAB
1,2 cm FACTORY-SUPPLIED
NON-COMBUSTIBLE BOARD
Figure 5.5 Front Side Finishing Detail
Figure 5.3 Clearances To Combustible/Non-Combustible
Mantels Or Other Combustibles/Non-Combust-
ibles Above Appliance.
8,90 cm
Note: For non-combustible fireplace finish material (marble,
stone, etc) specifications refer to Section 13.C.
NON-COMBUSTIBLE
BOARD SHIPPED
WITH APPLIANCE
Mantel Leg (Combustible/Non-Combustible)
2,5 cm
TOP VIEW
8 cm
MINIMUM
UNLIMITED
18 cm
Figure 5.4 Non-Combustible Mantel Leg or Wall Projections
(Acceptable on both sides of opening)
2,5 cm
AIR SPACE
Figure 5.6 Non-Combustible Zone
Note: AIR SPACE denoted in Figure 5.6 is defined by the
nailing tabs and metal standoffs.
Note: Factory installed non-combustible board may only
be replaced with HHT product code SUPERM-60 material
and must be fully replaced in its entirety.
20
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
Termination Locations
6
A. Vent Termination Minimum Clearances
A
B
15,2 cm (minimum) up to 50,8 cm
45,7 cm minimum
WARNING
50,8 cm and over
0 cm minimum
Fire Risk.
Gas, Wood or Fuel Oil
Termination Cap
Maintain vent clearance to combustibles as
specified.
• DO NOT pack air space with insulation or other
materials.
B
Failure to keep insulation or other materials away
from vent pipe may cause overheating and fire.
A*
Gas
Termination
Cap **
HORIZONTAL
OVERHANG
51 cm
VERTICAL
WALL
LOWEST
DISCHARGE
OPENING
*
If using decorative cap cover(s), this distance may need to be
increased. Refer to the installation instructions supplied with the
decorative cap cover.
TERMINATION
CAP
X
** In a staggered installation with both gas and wood or fuel oil
terminations, the wood or fuel oil termination cap must be
higher than the gas termination cap.
30,5 cm
ROOF PITCH
IS X/ 30,5 cm
Figure 6.2 Staggered Termination Caps
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
Angle
H (Min.) cm
0°-26.6°
..........................................................30*
26.6°-30.3° ..........................................................38*
30.3°-33.7° ..........................................................46*
33.7°-36.9° ..........................................................61*
36.9°-39.8° ..........................................................76
39.8°-42.5° ..........................................................99
42.5°-45.0° ........................................................122
45.0°-49.4° ........................................................152
49.4°-53.1° ........................................................183
53.1°-56.3° ........................................................213
56.3°-59.0° ........................................................229
59.0°-60.3° ........................................................244
*.91 M minimum in snow regions
Figure 6.1 Minimum Height From Roof To Lowest Discharge
Opening
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
21
O
N
V
P
L
K
K
Electrical
Service
R
V
V
E
C
V
Q
A
F
C
(See Note 2)
V
Measure vertical clearances from this surface.
B
J
B
V
V
V
B
V
i
M
D
V
G
V
X
A
H OR i
Measure horizontal clearances from this surface.
= VENT TERMINAL
X
= AIR SUPPLY INLET
= AREA WHERE TERMINAL IS NOT PERMITTED
V
J** = 2.13 m.................... clearance above paved
A
B
= 31 cm ......................clearances above grade, veranda,
(See Note 1)
(See Note 1)
sidewalk or a paved driveway
located on public property
porch, deck or balcony
= 31 cm ......................clearances to window or door
that may be opened, or to perma-
K
L
=
15 cm ....................clearance from sides of electri-
(See Note 5)
cal service
nently closed window. (Glass)
= 31 cm .....................clearance above electrical
C
= 46 cm ......................vertical clearance to unventilated
soffit or to ventilated soffit located
above the terminal
(See Note 5)
service
Covered Alcove Applications
M*** = 46 cm...................clearance under veranda, porch,
deck, balcony or overhang
76 cm.......................for vinyl clad soffits and below
electrical service
D
E
F
=
23 cm .....................clearance to outside corner
107 cm ............ vinyl
= 15 cm ......................clearance to inside corner
N
O
P
= 15 cm .............. non-vinyl sidewalls
31 cm .............. vinyl sidewalls
= 46 cm .............. non-vinyl soffit and overhang
107 cm ............ vinyl soffit and overhang
= 2.4 m
= 91 cm ......................not to be installed above a gas
meter/regulator assembly within 3
feet (90 cm) horizontally from the
center-line of the regulator
G
H
= 1,8 m.......................clearance to gas service regulator
flue outlet
= 31 cm ......................clearance to non-mechanical
QMIN
91 cm
1,8 m
2,7 m
3,7 m
RMAX
air supply inlet to building or the
combustion air inlet to any other
appliance
(See Note 2)
1 cap
2 caps
3 caps
4 caps
2 x Q ACTUAL
1 x Q ACTUAL
2/3 x Q ACTUAL
1/2 x Q ACTUAL
i
= 1,8 m ......................clearance to a mechanical (pow-
(See Note 2)
ered) air supply inlet
QMIN = # termination caps x 3 RMAX = (2 / # termination caps) x QACTUAL
** a vent shall not terminate directly above a sidewalk or paved driveway
which is located between two single family dwellings and serves both
dwellings.
Note 3: Local codes or regulations may require different clearances.
Note 4: Termination caps may be hot. Consider their proximity to
doors or other traffic areas.
*** only permitted if veranda, porch, deck or balcony is fully open on a
minimum of 2 sides beneath the floor, or meets Note 2.
Note 5: Location of the vent termination must not interfere with access
to the electrical service.
Note 1: On private property where termination is less than 2.1 m above a
sidewalk, driveway, deck, porch, veranda or balcony, use of a listed cap
shield is suggested. (See vents components page)
Vent system termination is NOT permitted in screened porches.
Note 2: Termination in a covered alcove space (spaces open only on one
side and with an overhang) are permitted with the dimensions specified
for vinyl or non-vinyl siding and soffits. 1. There must be .91 m minimum
between termination caps. 2. All mechanical air intakes within 3 m of a
termination cap must be a minimum of .91 m below the termination cap. 3.
All gravity air intakes within .91 m of a termination cap must be a minimum
of .30 m below the termination cap.
Vent system termination is permitted in porch areas with two or more
sides open. You must follow all side walls, overhang and ground
clearances as stated in the instructions.
Heat & Glo assumes no responsibility for the improper performance
of the appliance when the venting system does not meet these
requirements.
Figure 6.3 Minimum Clearances for Termination
22
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
Vent Information and Diagrams
7
A. Approved Pipe
D. Measuring Standards
This appliance is approved for use with Hearth & Home
Technologies SLP venting systems. Refer to Section 17.B
for vent component information.
Vertical and horizontal measurements listed in the vent
diagrams were made using the following standards.
• Pipe measurements are shown using the effective length
of pipe (see Figure 7.2).
DO NOT mix pipe, fittings or joining methods from differ-
ent manufacturers.
• Measurements are made from the appliance outer wrap,
not from the standoffs.
The pipe is tested to be run inside an enclosed wall.
There is no requirement for inspection openings at each
joint within the wall.
• Horizontal terminations are measured to the outside
mounting surface (flange of termination cap).
WARNING! Risk of Fire or Asphyxiation. This appli-
ance requires a separate vent. DO NOT vent to a pipe
serving a separate solid fuel burning appliance.
• Vertical terminations are measured to bottom of
termination cap.
• Horizontal pipe installed level with no rise.
B. Vent Table Key
The abbreviations listed in this vent table key are used in
the vent diagrams.
Effective Height/Length
Pipe
SLP4
cm
10
mm
102
152
305
610
914
1219
Symbol
Description
SLP6
15
Effective
Height/
Length
First section (closest to appliance) of vertical length
V1
SLP12
SLP24
SLP36
SLP48
SLP6A
SLP12A
30
61
Second section of vertical length
V2
H1
H2
91
First section (closest to appliance) of horizontal length
Subsequent sections of horizontal length
122
5 - 15 51 - 152
5 - 30 51 - 305
C. Use of Elbows
Figure 7.2 SLP Pipe Effective Length
Diagonal runs have both vertical and horizontal vent as-
pects when calculating the effects. Use the rise for the
vertical aspect and the run for the horizontal aspect (see
Figure 7.1).
E. Vent Diagrams
General Rules:
Two 45º elbows may be used in place of one 90º elbow. On
45º runs, one foot of diagonal is equal to 21.6 cm horizontal
run and 21.6 cm vertical run. A length of straight pipe is
allowed between two 45º elbows (see Figure 7.1).
• When penetrating a combustible wall, a wall shield
firestop must be installed.
• When penetrating a combustible ceiling, a ceiling firestop
must be installed.
• Horizontal runs of vent do not require vertical rise;
horizontal runs may be level.
Vertical
21,6 cm
Horizontal
Figure 7.1
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
23
WARNING
Fire Risk. Explosion Risk.
Do NOT pack insulation or other combustibles between ceiling firestops.
•
•
ALWAYS maintain specified clearances around venting and firestop systems.
Install wall shield and ceiling firestops as specified.
Failure to keep insulation or other material away from vent pipe may cause fire.
Top Vent - Horizontal Termination
Venting with 1 elbow
Note: Use SLP Series
components only.
V Minimum
90 Elbow
30,5 cm
61,0 cm
91,4 cm
120 cm
H1 Maximum
61,0 cm
91,4 cm
1,5 m
2,1 m
4,3 m
H Max. =4,3 m
V + H Max. = 12,2 m
V1
H1
Figure 7.3
24
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Top Vent - Horizontal Termination - (continued)
Top Vent - Horizontal Termination
Venting with 2 elbows
V Minimum
90° Elbow
305 mm
610 mm
914 mm
1,2 m
H1 + H2 Maximum
30,5 cm
61,0 cm
1,2 m
Note: Use SLP Series
components only.
1,8 m
4,6 m
H + H1 Max. =4,6 m
V + H + H1 Max. = 12,2 m
V1
H2
H1
INSTALLED
HORIZONTALLY
Figure 7.4
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Exhaust restrictor Instructions
Top Vent - Vertical Termination
No Elbows
1. Locate the two pilot holes located in the inside firebox
heat shield as shown in Figure 7.6.
V1 = 13,4 m
2. Center the exhaust restrictor such that the through
holes in the vent restrictor align with the pilot holes in
the heat shield.
Note: If installing a vertical vent/termination off the top of the
appliance, the optional exhaust restrictor may be needed.
3. Use (2) 1,3 cm self-piercing screws to secure vent
restrictor to firebox heat shield. See Figure 7.7.
Note: Use SLP Series
components only.
PILOT HOLES
V1
Figure 7.6 Location of Pilot Holes
Figure 7.7 Exhaust Restrictor Installation
4. In some applications, such as those where the fire-
place is elevated off the floor, the vent restrictor may
be painted, but painting is not required.
Figure 7.5 Vertical Vent Maximum
Exhaust restrictors are recommended for these vertically
terminated products which have excessive draft. Exhaust
restrictors will compensate for high draft, and restore vi-
sual flame height. If the vent configuration has a total
vertical of 4,6 m - 13,4 m, an exhaust restrictor may be
needed. The exhaust restrictor can be located in the ap-
pliance manual bag.
NOTICE: Before painting, contact your dealer for informa-
tion on the appropriate high temperature paint.
26
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
Top Vent - Vertical Termination
Venting with 2 elbows
V1 Minimum
90° Elbow
15,2 cm
45,7 cm
91,4 cm
1,1 m
H Maximum
61,0 cm
91,4 cm
1,5 m
V2
*
V1 + V2 Minimum
*
*
*
*
*
*
*
2,1 m
*
4,6 m
*
H Max. = 4,6 m
V1 + V2 + H Max. = 12,2 m
* No specific restrictions on this value EXCEPT V1 + V2 + H cannot exceed 12,2 m
Note: Use SLP Series
components only.
V2
V1
H1
Figure 7.8
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
27
Top Vent - Vertical Termination
Venting with 3 elbows
V1 Minimum
90° Elbow
30,5 cm
61,0 cm
91,4 cm
1,2 m
H1 + H2 Maximum
30,5 cm
61,0 cm
1,2 m
V2
*
V1 + V2 Minimum
*
*
*
*
*
*
*
1,8 m
*
4,3 m
*
H Max. = 4,3 m
V1 + V2 + H1 + H2 Max. = 12,2 m
* No specific restrictions on this value EXCEPT V1 + V2 + H1 + H2 cannot exceed 12,2 m
Note: Use SLP Series
components only.
V2
H1
H2
V1
INSTALLED
HORIZONTALLY
Figure 7.9
28
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
Top Vent - Vertical Termination
Venting with 4 elbows
V1 Min.
H1 Max.
V2 Min.
H2 Max.
V3 Min.
Note: Use SLP Series
components only.
45,7 cm
1,2 m
1,2 m
1,2 m
1,0 m
V1 + V2 + V3 + H1 + H2 Maximum= 12,2 m
V3
V2
H2
H1
V1
Figure 7.10
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
29
Vent Clearances and Framing
8
A. Pipe Clearances to Combustibles
B. Wall Penetration Framing
WARNING! Risk of Fire! Maintain air space clearance to
vent. DO NOT pack insulation or other combustibles:
Combustible Wall Penetration
Whenever a combustible wall is penetrated, you must
frame a hole for the wall shield firestop(s). The wall shield
firestop maintains minimum clearances and prevents cold
air infiltration.
• Between ceiling firestops
• Between wall shield firestops
• Around vent system
• The opening must be framed on all four sides using the
same size framing materials as those used in the wall
construction.
Failure to keep insulation or other material away from
vent pipe may cause over heating and fire.
Note: Heat shields MUST overlap by a minimum of 38 cm.
• SLP heat shield - designed to be used on a wall 11,1 cm to 19,4 cm thick.
• SLP pipe - A wall shield firestop must be placed on each
side of an interior wall. A minimum 3,8 cm overlap of at-
tached heat shields must be maintained.
• If wall thickness is less than 11,1 cm the existing heat shields must be field tricmed.
If wall thickness is greater than 19,4 cm a DVP-HSM-B will be required.
• See Section 10.K. for information for regarding the in-
stallation of a horizontal termination cap.
Heat
6,4 cm
Shield
top clearance
Heat
7,6 cm
top clearance
Non-Combustible Wall Penetration
Shield
If the hole being penetrated is surrounded by noncom-
bustible materials such as concrete, a hole with diameter
2,54 cm greater than the pipe is acceptable.
2,5 cm
clearance around
vertical sections
2,5 cm
bottom
clearance
1,3 cm
clearance
bottom & sides
Whenever a non-combustible wall is penetrated, the wall
shield firestop is only required on one side and no heat
shield is necessary.
Wall
Shield
Firestop
WALL
Figure 8.1 Horizontal Venting Clearances To Combustible
Materials
DO NOT PACK WITH
INSULATION OR
OTHER MATERIAL
25,4 cm
25,4 cm
B
A
A*
B
122 cm
120 cm
* Shows center of vent framing hole for top venting. The center of the hole
is one 2,54 cm above the center of the horizontal vent pipe.
Figure 8.2 Wall Penetration
30
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
C. Install the Ceiling Firestop
A ceiling firestop MUST be used between
floors and attics.
• SLP pipe only - Frame opening 22,86 cm
x 22,86 cm whenever the vent penetrates
a ceiling/floor (see Figure 8.3).
ATTIC ABOVE
• Frame the area with the same sized lumber
as used in ceiling/floor joist.
• The ceiling firestop may be installed above or
below the ceiling joists when installed with a
attic insulation shield. It must be under joists
between floors that are not insulated. Refer
to Figure 8.4.
A
• Secure with three fasteners on each side.
WARNING! Risk of Fire! DO NOT pack insu-
lation around the vent. Insulation must be kept
back from the pipe to prevent overheating.
A
A
PIPE
SLP
22,95 cm
Figure 8.3 Installing Ceiling Firestop
INSTALL ATTIC INSULATION SHIELDS
BEFORE OR AFTER INSTALLATION OF VENT SYSTEM
3 FASTENERS
PER SIDE
CEILING FIRESTOP
CEILING FIRESTOP
INSTALLED BELOW CEILING
INSTALLED ABOVE CEILING
Figure 8.4 Installing the Attic Shield
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
31
D. Install Attic Insulation Shield
BEND ALL TABS INWARD 90°
TO MAINTAIN CLEARANCE
AND PREVENT INSULATION
FROM FALLING INSIDE
WARNING! Fire Risk. DO NOT allow loose materials or
insulation to touch vent. Hearth & Home Technologies
Inc. requires the use of an attic shield.
Attic shields must meet specified clearance and be se-
cured in place.
Flat Ceiling Installation
BEND 3 TABS
OUTWARD TO
• Remove one shield from box.
FASTEN TO CEILING
FIRESTOP-BEND
REMAINING TABS
INWARD 90 DEGREES
TO MAINTAIN
NOTICE: Cut previously installed batt insulation to make
room for the attic insulation shield.
• Wrap shield around pipe if pipe is already installed in
area to be insulated.
CLEARANCE
INSERT 3
SCREWS
• Match the three holes in each side and fasten with three
screws to form a tube.
• Bend three tabs on the bottom of the shield outward to
allow attachment to the ceiling firestop.
• Bend the remaining bottom tabs inward 90° to maintain
the air space between the pipe and the shield. Set the
shield on the ceiling firestop and attach to the firestop.
Figure 8.5 Attic Insulation Shield
• Bend all tabs inward 90° around the top of the shield.
These tabs must be used to prevent blown insulation
from getting between the shield and vent pipe, and to
maintain air space clearance.
Vaulted Ceiling Installation
• Remove one shield from box.
NOTICE: Cut previously installed batt insulation to make
room for the attic insulation shield.
• Cut the attic insulation shield (if application is for vaulted
ceiling) to fit your ceiling pitch. Snip cut edge to recreate
2,54 cm bend tabs all the way around the bottom.
• Wrap shield around pipe if pipe is already installed in
area to be insulated.
• Match the three holes in each side and fasten with three
screws to form a tube.
• Bend three tabs on the bottom of the shield outward to
allow attachment to the ceiling firestop.
• Bend the remaining bottom tabs inward 90° to maintain
the air space between the pipe and the shield. Set the
shield on the ceiling firestop and attach to the firestop.
• Bend all tabs inward 90° around the top of the shield.
These tabs must be used to prevent blown insulation
from getting between the shield and vent pipe, and to
maintain air space clearance.
32
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
Appliance Preparation
9
A. Top Vent
ELBOW HEAT SHIELD
SHOWN AS INSTALLED
CAUTION! Risk of Cuts, Abrasions or Flying Debris.
Wear protective gloves and safety glasses during instal-
lation. Sheet metal edges are sharp.
ELBOW HEAT SHIELD SHOWN
IN SHIPPING POSITION
PIPE GASKET
Figure 9.2 Elbow Shield Shown Installed
Figure 9.1 Elbow Shield Shown as Shipped
If venting with a 90 degree elbow directly off of the top of
the appliance, the elbow heat shield must be repositioned
as shown in Figure 9.2.
If venting vertically or using a straight section of vertical
pipe, remove the elbow heat shield and discard by remov-
ing the two 1/4 in. screws that secure the elbow heat shield
to the top of the fireplace.
For all venting applications, ensure that the pipe gasket is
in place before attaching any pipe section. This gasket is
shipped in place around the starting collar. See Figure 9.2.
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
33
B. Securing and Leveling the Appliance
WARNING! Risk of Fire! Prevent contact with:
• Sagging or loose insulation
• Insulation backing or plastic
• Framing and other combustible materials
Block openings into the chase to prevent entry of blown-
in insulation. Make sure insulation and other materials
are secured.
DO NOT notch the framing around the appliance
standoffs. Failure to maintain air space clearance may
cause overheating and fire.
For details on setting the appliance in the framing, refer to
section 13.A. The diagram shows how to properly position,
level, and secure the appliance (see Figure 9.3). Nailing
tabs are provided to secure the appliance to the framing
members.
NAILING TABS
BOTH SIDES
• Bend out nailing tabs on each side.
• Place the appliance into position.
• Keep nailing tabs flush with the framing.
• Level the appliance from side to side and front to back.
Figure 9.3 Proper Positioning, Leveling And Securing of an
Appliance
• Shim the appliance as necessary. It is acceptable to use
wood shims underneath the appliance.
• Secure the appliance to the framing by using nails or
screws through the nailing tabs.
• Secure the appliance to the floor by inserting two screws
through the pilot holes at the bottom of the appliance.
Figure 9.3 shows the fireplace installed on the floor.
However, this fireplace can be elevated off the floor
provided that the fireplace is properly supported by framing
materials and the ceiling clearances are maintained.
34
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Vent Pipe (SLP Pipe)
10
A. Assemble Vent Sections
To attach the first vent component to the starting collars
of the appliance:
• Lock the vent components into place by sliding the pipe
section onto the collar.
• Align the seam of the pipe and seam of collar to allow
engagement. Rotate the vent component to lock into
place. Use this procedure for all vent components. See
Figure 10.1.
Note: Align seams to engage pipe,
then rotate counterclockwise to lock
• Slide the gasket over the first vent section and place it
flush to the appliance. This will prevent cold air infiltration.
High temperature caulk (150 ºC minimum continuous
exposure rating) may be used to hold the part in place.
Figure 10.1 Adding Venting Components
• Continue adding vent components, locking each
succeeding component into place.
• Ensure that each succeeding vent component is securely
fitted and locked into the preceding component.
Commercial, Multi-family (Multi-level exceeding two sto-
ries), or High-Rise Applications
For Installation into a commercial, multi-family (multi-level
exceeding two stories) or high-rise applications: All outer
pipe joints must be sealed with high temperature (150 ºC
minimum continuous exposure rating) silicone, including
the slip section that connects directly to the horizontal ter-
mination cap.
• Apply a bead of silicone sealant inside the female outer
pipe joint prior to joining sections. See Figure 10.2
Figure 10.2 High Temperature Silicone Sealant
(300ºF minimum continuous exposure rating)
• Only outer pipes need to be sealed. All unit collar, pipe,
slip section, elbow and cap outer flues shall be sealed
in this manner, unless otherwise stated.
WARNING! Risk of Fire or Explosion! DO NOT break
silicone seals on slip sections. Use care when removing
termination cap from slip pipe. If slip section seals are bro-
ken during removal of the termination cap, vent may leak.
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
35
B. Assemble Slip Sections
C. Secure The Vent Sections
• Slide the inner flue of the slip section into the inner flue of
the pipe section and the outer flue of the slip section over
the outer flue of the pipe section. See Figure 10.3.
• Vertical runs of pipe must be supported every 244 cm.
• Horizontal sections must be supported every 152 cm.
• Vent supports or plumbers strap (spaced 120º apart)
may be used to support. See Figures 10.5 and 10.6.
• Slide together to the desired length.
• Wall shield firestops may be used to provide horizontal
support.
• Ceiling firestops have tabs that may be used to provide
vertical support.
WARNING! Risk of Fire, Explosion or Asphyxiation!
Improper support may allow vent to sag and separate.
Use vent run supports and connect vent sections per in-
stallation instructions. DO NOT allow vent to sag below
connection point to appliance.
Pilot hole
Figure 10.3 Slip Section Pilot Holes
• Maintain a 3,8 cm overlap between the slip section and
the pipe section.
• Secure the pipe and slip section with two screws no
longer than 1,3 cm, using the pilot holes in the slip Sec-
tion. See Figure 10.4.
Figure 10.5 Securing Vertical Pipe Sections
Figure 10.4 Screws into Slip Section
• Continue adding pipe as necessary following instructions
in “Assembling Pipe Sections.”
NOTICE: If slip section is too long, the inner and outer flues
of the slip section can be cut to the desired length.
Figure 10.6 Securing Horizontal Pipe Sections
NOTICE: When installing a vent system with an HRC
termination cap, all pipe system joints shall be sealed using
a high temperature (150 ºC minimum continuous exposure
rating) silicone sealant.
• Apply a bead of silicone sealant inside the female outer
pipe joint prior to joining sections.
• Only outer pipes are sealed, sealing the inner flue is not
required.
• All unit collar, pipe, slip section, elbow and cap outer
flues shall be sealed.
36
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
bottom is at least 5,1 cm below the ceiling (Figure 10.9).
D. Disassemble Vent Sections
• Level the support box both vertically and horizontally and
temporarily tack it in place through the inside walls into
the roof sheathing.
• Rotate either section (see Figure 10.7) so the seams on
both pipe sections are aligned as shown in Figure 10.8.
• Pull carefully to separate the pieces of pipe.
• Use tin snips to cut the support box from the top corners
down to the roof line and fold the resulting flaps to the
roof. See Figure 10.10.
• Nail the flaps to the roof AFTER running a bead of non
hardening sealant between the flaps and the roof.
WARNING! Risk of Fire! Clean out ALL materials from
inside the support box and complete the vertical vent run
and termination.
LEVEL
CATHEDRAL CEILING
SUPPORT BOX
Figure 10.7 Rotate Seams for Disassembly
5,1 cm MIN. BELOW
FINISHED CEILING
CUT HOLE 3 mm GREATER
IN SIZE THAN PATTERN OF
SUPPORT BOX AS IT IS
PROJECTED ONTO ROOF
LINE
Figure 10.9
Figure 10.8 Align and Disassemble Vent Sections
E. Install Decorative Ceiling Components
A decorative ceiling thimble can be installed on a flat ceil-
ing through which the vent passes. The decorative ceiling
thimble is used to cover the firestop.
• Seal the gap between the vent pipe and firestop using
high temperature (150 ºC minimum continuous exposure
rating) silicone to prevent cold air infiltration.
• Install the decorative ceiling thimble by sliding it up to
the ceiling and attaching it using the provided screws.
Adecorative cathedral ceiling support box can be installed
on a cathedral ceiling through which the vent passes.
Figure 10.10
• Use a plumb-bob to mark the center line of the venting
system on the ceiling and drill a small hole through the
ceiling and roof at this point. Locate the hole and mark
the outline of the cathedral ceiling support box on the
outside roof.
• Remove shingles or other roof covering as necessary to
cut the rectangular hole for the support box. Cut the hole
3 mm larger than the support box outline.
• Lower the support box through the hole in the roof until its
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
37
F. Install Metal Roof Flashing
• See minimum vent heights for various pitched roofs
(Figure 10.11) to determine the length of pipe to extend
through the roof.
CAULK
• Slide the roof flashing over the pipe sections extending
through the roof as shown in Figure 10.12.
HORIZONTAL
OVERHANG
51 cm
VERTICAL
WALL
LOWEST
DISCHARGE
OPENING
Figure 10.12
G. Assemble and Install Storm Collar
TERMINATION
CAP
CAUTION! Risk of Cuts, Abrasions or Flying Debris.
Wear protective gloves and safety glasses during instal-
lation. Sheet metal edges are sharp.
X
30,5 cm
• Connect both halves of the storm collar with two screws
(see Figure 10.13).
ROOF PITCH
IS X/ 30,5 cm
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
• Wrap the storm collar around the exposed pipe section
closest to the roof and align brackets. Insert a bolt
(provided) through the brackets and tighten the nut to
complete the storm collar assembly. Make sure the collar
is tight against the pipe section.
• Slide the assembled storm collar down the pipe section
until it rests on the roof flashing (see Figure 10.14).
Angle
H (Min.) cm
0°-26.6°
..........................................................30*
26.6°-30.3° ..........................................................38*
30.3°-33.7° ..........................................................46*
33.7°-36.9° ..........................................................61*
36.9°-39.8° ..........................................................76
39.8°-42.5° ..........................................................99
42.5°-45.0° ........................................................122
45.0°-49.4° ........................................................152
49.4°-53.1° ........................................................183
53.1°-56.3° ........................................................213
56.3°-59.0° ........................................................229
• Caulk around the top of the storm collar (see Figure 10.15).
59.0°-60.3° ........................................................244
*.91 M minimum in snow regions
Figure 10.11 Minimum Height From Roof To Lowest Discharge
Opening
Figure 10.13 Assembling the Storm Collar
NOTICE: Failure to properly caulk the roof flashing and
pipe seams may permit entry of water.
• Caulk the gap between the roof flashing and the outside
diameter of the pipe.
• Caulk the perimeter of the flashing where it contacts the
roof surface. See Figure 10.12.
• Caulk the overlap seam of any exposed pipe sections
that are located above the roof line.
Figure 10.14 Assembling the Storm Collar Around the Pipe
38
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
H. Install Vertical Termination Cap
J. Heat Shield Requirements for Horizontal
Termination
• Attach the vertical termination cap by sliding the inner
collar of the cap into the inner flue of the pipe section
while placing the outer collar of the cap over the outer
flue of the pipe section.
WARNING! Risk of Fire! To prevent overheating and fire,
heat shields must extend through the entire wall thick-
ness.
• Secure the cap by driving three self-tapping screws
(supplied) through the pilot holes in the outer collar of the
cap into the outer flue of the pipe (see Figure 10.15).
• DO NOT remove the heat shields attached to the
wall shield firestop and the horizontal termination cap
(shown in Figure 10.17).
• Heat shields must overlap 3,8 cm minimum.
TERMINATION CAP
There are two sections of the heat shield. One section is
factory-attached to the wall shield firestop. The other sec-
tion is factory-attached to the cap. See Figure 10.17.
If the wall thickness does not allow the required 3,8 cm
heat shield overlap when installed, an extended heat
shield must be used.
• If the wall thickness is less than 11,1 cm, the heat shields
on the cap and wall shield firestop must be trimmed. A
minimum 3,8 cm overlap MUST be maintained.
(1 of 3)
• Use an extended heat shield if the finished wall thick-
ness is greater than 18,4 cm.
• The extended heat shield may need to be cut to length
maintaining sufficient length for a 3,8 cm overlap be-
tween heat shields.
STORM
COLLAR
SCREWS
• Attach the extended heat shield to either of the existing
heat shields using the screws supplied with the extend-
ed heat shield. Refer to vent components diagrams in
the back of this manual.
CAULK
• Rest the small leg on the extended heat shield on top of
the pipe section to properly space it from the pipe sec-
tion.
Figure 10.15
I. Install Decorative Wall Components
Important Notice: Heat shields may not be field constructed.
A decorative wall thimble can be installed on wall through
which the vent passes. The decorative wall thimble is used
to cover the firestop.
• Slide the decorative wall thimble over the last section of
horizontal pipe before connecting the termination cap to
the pipe.
• Once the pipe section and the termination cap have been
connected, slide the wall thimble up to the interior wall
surface and attach with screws provided. See Figure
10.16.
Figure 10.16 Wall Thimble
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
39
K. Install Horizontal Termination Cap
WARNING! Risk of Fire! The telescoping flue section
of the termination cap MUST be used when connecting
vent.
• 3,8 cm minimum overlap of flue telescoping section
is required.
Failure to maintain overlap may cause overheating and
fire.
• Vent termination must not be recessed in the wall. Siding
may be brought to the edge of the cap base.
• Flash and seal as appropriate for siding material at
outside edges of cap.
• When installing a horizontal termination cap, follow the
cap location guidelines as prescribed by current local or
national codes and refer to Section 6 of this manual.
CAUTION! Risk of Burns! Local codes may require in-
stallation of a cap shield to prevent anything or anyone
from touching the hot cap.
Note: When using termination caps with factory-supplied heat
shield attached, no additional wall shield firestop is required on
the exterior side of a combustible wall.
HEAT SHIELD OR
HEAT SHIELD
EXTENDED
HEAT SHIELD
3,8 CM MIN.
OVERLAP
WALL SHIELD
FIRESTOP
SLIP SECTION
CAN BE EXTENDED
INNER VENT
SHEATHING
OUTER VENT
INTERIOR
EXTERIOR
Figure 10.17 Venting through the wall
40
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
Gas Information
11
A. Gas Pressure Requirements
B. Gas Connection
Pressure requirements for XLR-CE fireplaces are shown
in Table 11.1 below.
Note: Have the gas supply line installed in accordance with
local building codes by a qualified installer approved and/or
licensed as required by the locality.
Two taps are provided on the right hand side of the gas
control for a test gauge connection to measure the inlet
and outlet pressures.
Note: Before the first firing of the appliance, the gas supply
The fireplace and its individual shut-off valve must be dis-
connected from the gas supply piping system during any
pressure testing of the system at test pressures in excess
of 60 mbar.
line should be purged of any trapped air.
Note: Consult local building regulations to properly size the gas
supply line leading to the (Rp 1/2 in.) hook-up at the unit.
If the fireplace must be isolated from the gas supply pip-
ing system by closing an individual shut-off valve, it must
be of the handle-less type.
Incoming gas line should be piped into the valve compart-
ment and connected to the ISO 7-Rp 1/2 (BSP Rp 1/2)
threaded gas inlet connection on the manual shutoff valve.
WARNING
Leak test all gas line points and the gas control valve prior
to and after starting the gas appliance.
Fire Risk
Explosion Risk
WARNING
High pressure will damage valve.
• Disconnect gas supply piping BEFORE
pressure testing gas line at test pressures
above 60 mbar.
CHECK FOR GAS LEAKS
Explosion Risk
Fire Risk
• Close the manual shutoff valve BEFORE
pressure testing gas line at test pressures
equal to or less than 60 mbar.
Asphyxiation Risk
• Check all fittings and connections.
• Do not use open flame.
• After the gas line installation is complete, all
connections must be tightened and checked
for leaks with a commercially-available, non-
corrosive leak check solution. Be sure to rinse
off all leak check solution following testing.
ON/OFF/REMOTE
SWITCH
GAS VALVE
Fittings and connections may have loosened
during shipping and handling.
CONTROL
MODULE
C. Access Through the Valve Assembly
BATTERY
PACK
DC ADAPTER
Refer to Section 16.C.
Figure 11.1. Valve Components
Natural Gas
(G20)
Propane
(G31)
Propane
(G31)
Butane
(G30)
Butane
(G30)
Natural Gas
(G25)
CAT
I2H, I2E, I2E+
20 mbar
8.7 mbar
I3P
I3P
I3B/P
I3B/P
I2E+
Inlet Pressure
Burner Pressure
Gas Rate
37 mbar
25 mbar
.134 m3
50 mbar
25 mbar
.134 m3
30 mbar
25 mbar
.111 m3
50 mbar
25 mbar
.111 m3
25 mbar
8.7 mbar
.40 m3
/
h
.405 m3
/
/
/
/
/
h
h
h
h
h
Heat Input (Net)
7.32 kW
DMS 42
51
6.74 kW
DMS .057
30
6.74 kW
DMS .057
30
6.44 kW
DMS 55
30
6.44 kW
DMS 55
30
7.32 kW
DMS 42
51
Burner Injector
Pilot Injector
Columns highlighted in gray = The gas control valve supplied with this product is approved for a maximum
inlet pressure of 37 mbar. For pressures over 37 mbar, an in line pressure regulator must be installed
upstream from the gas control valve.
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
41
Electrical Information
12
• This appliance is equipped with an IntelliFire Plus™
control valve which operates on a 6 volt system.
A. Wiring Requirements
NOTICE: This appliance must be installed by a qualified
electrician in accordance with the relevant national and
local regulations.
• Plug the 6-volt AC power supply into the appliance junction
cord to supply power to the unit OR install four AA cell
batteries (not included) into the battery pack before use.
• Wire the appliance junction cord to 230 VAC. This is
required for proper operation of the appliance.
• This appliance ships standard with an electrical supply
cord.
WARNING! Risk of Shock or Explosion! DO NOT wire
230 VAC to the valve or to the appliance wall switch. In-
correct wiring will damage controls.
NOTICE: If the supply cord is damaged, it must be replaced
by a special cord or assembly available from the manufac-
turer or its service agent.
NOTICE: The mains supply to the appliance must have
isolation of a minimum 3 mm contact separation in both
poles.
C. Optional Accessories Requirements
• This appliance may be used with a wall switch, wall
mounted thermostat and/or a remote control.
WARNING! Risk of Injury! The gas supply shall be shut
off prior to disconnecting the electrical power and remov-
ing batteries (if installed) before proceeding with any
maintenance to the appliance.
Wiring for optional Hearth & Home Technologies approved
accessories should be done now to avoid reconstruction.
Follow instructions that come with those accessories.
Optional Remote Control Receiver and Battery Pack
Location
B. IntelliFire Plus™ Ignition System Wiring
The battery tray, control module, and remote control re-
ceiver can be accessed through the air space between
the firebox front and the lower-front finishing cover panel.
The decorative front and glass assembly must be re-
moved to access these components.
• Wire the appliance junction cord to 230 VAC for proper
operation of the appliance.
WARNING! Risk of Shock or Explosion! DO NOT wire
IPI controlled appliance junction cord to a switched cir-
cuit. Incorrect wiring will override IPI safety lockout.
The battery tray is attached with Velcro to the inside of the
lower cover panel. The IPI control module and the remote
control receiver are placed on the firebox bottom.
• Refer to Figure 12.1, IntelliFire Plus™ Pilot Ignition (IPI)
Wiring Diagram.
NOTE: 1. Ignition module,
valve, pilot, and wall switch
operate on 6 volts. 230 VAC is
required at junction cord unless
equipped with battery back-up.
240V FAN (OPTIONAL)
MODULE RESET
SWITCH
GROUND TO
CHASSIS
TO OPTIONAL AUX300CE
BOX AND FAN ASSEMBLY
RC100
(OPTIONAL REMOTE
CONTROL)
WIRE ASSEMBLY
FLAME
SENSE
IGNITER
TO CORD
ASSEMBLY 120VAC
GRAY MODULE
AUX300CE MODULE (OPTIONAL)
FAN
WALL SWITCH
JUMPER WIRE
AUX 1
AUX 2
TO JUNCTION
CORD 230 VAC
TO OPTIONAL
COMPONENTS
ORANGE
(PILOT)
GREEN
(PILOT)
BATTERY PACK
6V DC
BLACK
RED
BROWN-
THERMOSTAT WIRE
ASSEMBLY / WALL
SWITCH WIRE
ΓΕΙΩΣΗ
Figure 12.1 IntelliFire Plus™ Pilot Ignition (IPI) Wiring Diagram with Wall Switch or Thermostat
42
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
D. Electrical Service and Repair
F. Blower
WARNING! Risk of Shock! Label all wires prior to dis-
connection when servicing controls. Wiring errors can
cause improper and dangerous operation. Verify proper
operation after servicing.
An optional fan and auxilliary box are available for this
appliance. Refer to instructions provided with GFK-240V
fan kit.
Use of the fan requires that the Junction cord (factory in-
stalled) be connected to 220/240 VAC service before per-
manently enclosing the heater. The service cord is found
on the right exterior side of the unit. See Figure 12.3 for
wire connection detail.
WARNING! Risk of Shock! Replace damaged wire with
type 105° C rated wire. Wire must have high temperature
insulation.
E. Junction Cord Information
The junction cord is installed at the factory. Refer to Figure
12.2 and 12.3. for more information.
Note: There is an alternative access to the junction cord.
This can be accessed by removing the valve assembly. See
Figures 11.1 and 11.2.
Figure 12.2. Junction Cord Information
240V BLOWER
GROUND TERMINAL TO
FIREPLACE CHASSIS
BLUE
JUNCTION CORD
BROWN
GREEN/
YELLOW
TO
MODULE
AUX 300 CE
OPTIONAL
COUNTRY OF
DESTINATION PLUG
Figure 12.3 Blower Circuit
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
43
Finishing
13
A. Framing and Finishing Instructions
WARNING! Risk of Fire! Comply with all minimum clear-
ances to combustibles as specified. Framing closer than the
minimums listed must be constructed entirely of noncom-
bustible materials (i.e., steel studs, concrete board, etc.)
FACTORY-INSTALLED
NON-COMBUSTIBLE BOARD
Finishing Instructions
It is important to follow the framing and finishing instruc-
tions to ensure proper placement of fireplace into the sur-
rounding framing/finishing materials.
Wall sheathing materials 1.3 cm thick are specified in
this installation manual to properly align with the factory-
installed non combustible material.
WARNING! Risk of Fire! DO NOT remove the factory-
installed non-combustible board or cover it with combus-
tible material, such as:
NAILING
TABS
• Drywall (gypsum board)
• Plywood
• Materials that do not meet the ASTM E 136 Non-com-
bustibility standard (below).
Removal of factory-installed, non-combustible board and/
or use of materials not meeting the ASTM E 136 standard
may cause fire.
Non-Combustible Materials Specification
Figure 13.1 Nailing Tabs Installation Position
Material which will not ignite and burn. Such materials are
those consisting entirely of steel, iron, brick, tile, concrete,
slate, glass or plasters, or any combination thereof.
Materials that are reported as passing ASTM E 136,
Standard Test Method for Behavior of Materials in a
Vertical Tube Furnace at 750 ºC and UL763 shall be
considered non-combustible materials.
1 IN.
Setting the Fireplace into the Framing
FRAMING
Unlikemanytraditional,single-sidedHeat&Glofireplaces,
this fireplace is recessed into surround framing. The left
and right nailing tabs were designed so the fireplace
is recessed to the correct location within the framing
materials.
1. Bend two nailing tabs away from fireplace 180 degrees
on both left and right nailing tabs. See Figure 13.1.
2. Screw each nailing tab to the adjoining framing
material. Ensure that the air space clearance is
maintained on the sides of the fireplace. See Figure
13.2.
NAILING TAB
1/2 IN. FACTORY-SUPPLIED
NON-COMBUSTIBLE BOARD
Figure 13.2 Front Side Finishing Detail
44
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING! Risk of Fire! Maintain specified air space
clearances to combustibles. Failure to comply with these
instructions may cause a fire or cause the appliance to
overheat.
Note: Refer to Section 13.C regarding installation details as-
sociated with the Inside and Overlap Fit methods.
CAUTION! Risk of Glass Damage and Cuts! DO NOT
drill or install any type of screw or fastener into the lower
cover panel. Sharp screw or fastener tips may penetrate
and break the glass or cause cuts.
PILOT HOLES (11) TO ATTACH NON-
COMBUSTIBLE BOARD TO FRAMING
The XLR-CE must be finished using either the Tonic or
Martini decorative fronts. See Figures 13.11 and 13.12.
The final fireplace installation can be accomplished by ei-
ther the Overlap Fit or Inside Fit method. Reference Sec-
tion 13.C regarding installation details associated with the
Inside Fit and Overlap Fit methods.
FACTORY-INSTALLED
NON-COMBUSTIBLE BOARD
It is acceptable to pre-drill holes and use self-tapped
screws in the factory-installed non-combustible board to
attach non-combustible backer board for tile, marble, etc.
Refer to Figure 13.3 for acceptable screw location and
screw length requirements.
Self-tapping screws up to 2,5 cm long can be installed
through the nailing tab and outer 4,5 cm edges of the
factory-installed non-combustible board to secure the
drywall adjacent to the factory-installed non-combustible
board. See Figure 13.3.
Do not drill or install screws which may penetrate the low-
er cover panel as this will restrict required access to the
glass, battery-back-up, and remote receiver. See Figure
13.3.
LOWER COVER PANEL
= 2,5 cm MAX. SELF-TAPPING SCREWS ALLOWED
The appliance is designed to accept 1,3 cm wall sheath-
ing materials such as drywall, plywood, wood composites,
or non-combustible materials. The type of material used
depends whether the installation is an Inside or Overlap
Fit Method. Refer to Section 13.C regarding installation
details associated with the Inside an Overlap Fit meth-
ods.
=
=
NO SCREWS ALLOWED
13 cm – 18 cm SELF-TAPPING SCREWS ALLOWED
NOTE: It is acceptable to use a high temperature (150 °C
minimum continuous exposure silicone sealant to ad-
here drywall to lower cover panel.
The factory-supplied non-combustible board must be
used in all installations. It must be directly attached to
structural framing adjacent to the appliance. Screw fas-
teners should be installed in the pilot holes provided in
the outer perimeter of the non-combustible board. See
Figure 13.3.
Figure 13.3 Finishing Details
The factory-supplied board is designed such that its edg-
es will be at the approximate center of the adjacent fram-
ing, assuming it is 1-1/2 in. (3,8 cm) nominal thickness.
This will allow the wallboard joints to occur on the center
of the framing where the panels can be fastened prop-
erly. If the framing thickness is less than 1-1/2 in. (3,8 cm)
nominal, such as with formed steel systems, then it may
be necessary to adjust the adjacent framing dimensions
so that the non-combustible board and wallboard joints
are centered on the framing.
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
45
• For the initial Taping Coat, it is critical that a general-
purpose chemically hardening joint compound, such as
SHEETROCK™ Brand Durabond™ Setting-Type Joint
Compound, be used to fill the joint and embed the mesh
tape. Fiberglass-mesh tape is recommended because it
will provide a more crack-resistant joint than one finished
with paper tape. Let theTaping Coat properly cure before
applying subsequent Finish Coats.
• For the second and third finishing coats, it is acceptable
to use a light-weight joint compound and standard
application, curing and sanding methods.
• Do not operate the fireplace during the drywall finishing
process. Allow the finish coat to cure for at least 24
hours prior to using the appliance.
FIREPLACE OPENING
43 cm TO 44 cm
Painting
If desired finishing includes a painted wall, 100% acrylic
latex with compatible primer is recommend around the
appliance. Oil-based or standard acrylic paints may
discolor due to heat exposure.
Wallboard Joint-Crack Prevention and Repair
Wallboard joints around the fireplace will be affected by
exposure to elevated temperatures, along with other en-
vironmental and structural factors. The specific methods
presented in the previous section will help prevent or
minimize development of cracks.
Figure 13.4 Required Fireplace Opening Height
Note: The lower cover panel must be pushed all the way
down. The outer finishing flanges should line up. The
fireplace opening must be between 43 cm and 44 cm for
the decorative fronts to fit correctly. See Figure 13.4.
If a crack does emerge adjacent the fireplace, it can be
permanently repaired by filling it with spackling paste or
paintable latex caulk, followed by repainting.
Finish and Sealing Joints
All joints between the finished wall sheating and
the appliance must be sealed with non-combustible
materials. Sealants, such as caulk or mastic used to
seal the gap between the wall and the fireplace, should
be rated at a minimum continuous exposure to 300°
F. Wall board joints can be taped and sealed with
combustible drywall tape.
Finishing Around Opening with Gypsum Wallboard
Gypsum wallboard (drywall) joints adjacent to the
fireplace opening require special attention to minimize
potential development of cracking. Hearth and Home
Technologies recommends the following steps to
minimize potential cracks in the finished drywall around
the fireplace opening:
• When installing gypsum wallboard around the fireplace,
install the hole for the fireplace opening in a single
wallboard sheet, if possible. This will minimize the joints
adjacent to the fireplace opening.
• The factory-supplied non-combustible board and the
gypsum wallboard must join on the structural framing,
where applicable. Wallboard and non-combustible
board should be fastened to the framing with at least
3,2 cm long screw fasteners, located within 3,8 from
each corner, and at no more than 30,5 intervals along
the joint length.
• The wall-board joints should be finished with a Taping
Coat, followed by at least two subsequent Finish Coats
of joint compound.
46
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING! Risk of Fire! DO NOT apply combustible
materials beyond the minimum clearances. Comply with
all minimum clearances to combustibles as specified in
this manual. Overlapping materials could ignite and will
interfere with proper operation of doors and louvers.
B. Mantel and Wall Projections
WARNING! Risk of Fire! Comply with all minimum clear-
ances to combustibles as specified. Framing closer than the
minimums listed must be constructed entirely of noncom-
bustible materials (i.e., steel studs, concrete board, etc.)
Failure to comply could cause fire.
WARNING! Risk of Fire! DO NOT install drywall or other
combustible materials over the factory-installed non-com-
bustible board. Overlapping materials could ignite.
Mantels (Combustible/Non-Combustible)
Decorative facing material thickness is measured from
the face of the factory-installed non-combustible board.
See Figure 13.7
1,3 cm
Thick Wall
Sheathing
30 cm
MAX.
FACTORY-INSTALLED
3,8 cm ABOVE STANDOFF
NON-COMBUSTIBLE BOARD
MEASUREMENT
NON-COMBUSTIBLE
FINISHING MATERIAL
0 - 2,5 cm THICK
FROM TOP OF
FIREPLACE
OPENING
36 cm
MIN.
TONIC DECORATIVE
FRONT SHOWN
Figure 13.5 Clearances To Combustible Mantels Or Other
Combustibles Above Appliance
Note: For non-combustible fireplace finish material (marble,
stone, etc) specifications refer to Section 13.C.
NON-COMBUSTIBLE
FINISHING MATERIAL
0 - 2,5 cm THICK
Mantel Leg (Combustible/Non-Combustible)
DRYWALL OR
EQUIVALENT (1,2 cm)
Figure 13.7 Overlap Fit Method (Tonic or Martini Decorative
Front)
TOP VIEW
Both the Tonic and Martini decorative fronts can be in-
stalled with an “Overlap” or “Inside Fit” method:
8 cm
MINIMUM
UNLIMITED
Overlap Requirement: See Figure 13.7.
Inside Fit requirement: See Figure 13.8 and 13.9.
18 cm
Non-Combustible Finish Materials
0 - 2,54 cm Thickness-Overlap Fit Method
Figure 13.6 Non-Combustible Mantel Leg or Wall Projections
(Acceptable on both sides of opening)
Both the Tonic and Martini decorative fronts are designed
to overlap finish materials 0 cm to 2,54 cm thick. See
Figure 13.6.
C. Facing Material
• Facing and/or finishing materials must not interfere with
air flow through louvers, operation of louvers or doors,
or access for service.
NOTICE: This 2.54 cm maximum not only includes the
decorative finish materials (marble, tile, slate, etc) but
also the mortar or adhesive used to attach the decorative
finish material.
• Facing and/or finishing materials must never overhang
into the glass opening.
The non-combustible finish material can be installed up to
the fireplace opening.
• Observe all clearances when applying combustible
materials.
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
47
Non-Combustible Finish Materials
0 cm to 10,16 cm Thick Inside Fit Method
Non-Combustible Finish Material 0-10 cm Thick
The Tonic decorative front is approved for inside fit appli-
cations. Non-combustible finishing materials up to 10,16
cm thick can be installed around the front (left, right, top,
and bottom).
1,9 cm
1,9 cm
For the Tonic decorative front inside fit applications, the
decorative front must be installed tight to the finishing
flanges and must not overlap any finish material.
4,6 cm
Ensure that no non-combustible finish materials are in-
stalled within 1,9 cm of the fireplace opening. The 1,9
cm spacing is required to provide clearance for removing
and installing the Tonic decorative front. See Figure 13.9.
Bottom Joint
FACTORY-INSTALLED
NON-COMBUSTIBLE
BOARD
Figure 13.9 Noncombustible Surface Finishing Material 0 - 10
cm Thick-Inside Fit Method (Tonic Decorative Front
Only)
0-10 cm
1,9 cm
52 cm APPLIANCE
OPENING (HEIGHT)
4,6 cm
0-10 cm
DRYWALL OR
EQUIVALENT
(1,3 cm)
Figure 13.8 Inside Fit Method (Tonic Decorative Front Only)
48
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
D. Decorative Fronts
WARNING! Risk of Fire! A decorative front is required
for this model. DO NOT operate this appliance without a
decorative front in place.
TONIC FRONT
Only doors certified for use with this appliance model may
be used. Contact your dealer for a list of doors that may
be used.
E
F
A
Inside and Overlap Fit
See Section 13.C.
B
C
D
Figure 13.12 Dimensions of Tonic Decorative Front
Table 1. Dimensions of Tonic Decorative Front
A
B
C
D
E
F
Top of decorative front to bottom of appliance.
Bottom of decorative front to bottom of appliance.
Inside dimension of decorative front (width).
Outside dimension of decorative front (width).
Inside dimension decorative front (height).
Outside dimension of decorative front (height).
67 cm
17,5 cm
99,1 cm
113 cm
32,7 cm
49,5 cm
TONIC DECORATIVE FRONT
(TN-SLR-**)
Figure 13.10 Tonic Decorative Front
Overlap Fit Only
See Section 13.C.
MARTINI DECORATIVE FRONT
(MT-SLR-**)
Figure 13.11 Martini Decorative Front
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
49
Appliance Setup
14
A. Remove Fixed Glass Assembly
See Section 14.E.
B. Remove the Shipping Materials
Remove shipping materials from inside or underneath the
firebox. The standard black rock media and manual bag
assembly are also shipped underneath the firebox.
C. Clean the Appliance
UPPER SPRING LATCH
LOWER GLASS CLIP
Clean/vacuum any sawdust that may have accumulated
inside the firebox or underneath in the control cavity.
D. Accessories
Install approved accessories per instructions included
with accessories. Contact your dealer for a list of ap-
proved accessories.
WARNING! Risk of Fire and Electric Shock! Use ONLY
Hearth & Home Technologies-approved optional acces-
sories with this appliance. Using non-listed accessories
could result in a safety hazard and will void the warranty.
E. Fixed Glass Assembly
WARNING! Risk of Asphyxiation! Handle fixed glass
assembly with care. Inspect the gasket to ensure it is
undamaged and inspect the glass for cracks, chips or
scratches.
Figure 14.1 Fixed Glass Assembly
F. Install the Mesh
The mesh front is included with the Tonic front. The Mar-
tini tinted glass front does not include mesh.
• DO NOT strike, slam or scratch glass.
• DO NOT operate fireplace with glass removed, cracked,
broken or scratched.
1. Remove fixed glass assembly as instructed.
2. Place glass assembly into mesh screen such that the
four mesh clips attached to the mesh assembly snap
into the four corresponding slots on the fixed glass as-
sembly.
• Replace as a complete assembly.
Removing Fixed Glass Assembly
1. Remove the decorative front.
2. Locate the two spring latches that are on the upper left
and right of the fireplace.
3. Use both index fingers to release spring latches. See
Figure 14.1.
4. Allow glass to tilt forward. Grasp glass on the upper
right and left sides and lift glass “up” and “out.”
Replacing Fixed Glass Assembly
1. Locate glide tabs on lower left and right corners.
2. Grasp glass on upper right and left sides and tilt bot-
tom of glass assembly toward fireplace.
3. Allow of the bottom gasketing of the glass assembly to
touch the face of the fireplace.
4. Put pressure on the glass as you allow the glass assem-
bly to drop into the two lower tabs. See Figure 14.1.
5. Tilt top of glass towards fireplace and engage both top
spring latches.
50
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
G. Air Shutter Setting
The air shutter is preset at the factory.
Figure 14.2 Air Shutter
Air Shutter Settings
N
P
B
XLR
0,16 cm
0,80 cm
Full Open
H. Media Options
Install only approved media options. These options include:
• MEDIA-AMBER
• MEDIA-BLACK
• MEDIA-CLEAR
• MEDIA-COBALT
• MEDIA-BK2 GEMS
• MEDIA-WH2 GEMS
• MEDIA-GEMS
• PORC-BASE
• XLR-LOGS
• MEDIA-STONES-2
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
51
Troubleshooting
15
With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do
experience a problem, this troubleshooting guide will assist a qualified service technician in the diagnosis of a problem and
the corrective action to be taken. This troubleshooting guide can only be used by a qualified service technician. Contact
your dealer to arrange a service call by a qualified service technician.
A. IntelliFire Plus™ Ignition System
Symptom
Possible Cause
Corrective Action
1. Pilot won’t light.
The ignitor/module
makes noise, but no
spark.
a. Incorrect wiring.
Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor are
connected to correct terminals on module and pilot assembly.
b. Loose connections or electrical
shorts in the wiring.
Verify no loose connections or electrical shorts in wiring from mod-
ule to pilot assembly. Verify connections underneath pilot assem-
bly are tight; also verify connections are not grounding out to metal
chassis, pilot burner, pilot enclosure, mesh screen if present, or any
other metal object.
c. Ignitor gap is too large.
d. Module.
Verify gap of igniter to right side of pilot hood. The gap should be
approximately 3 mm.
Turn ON/OFF rocker switch or wall switch to OFF position. Remove
ignitor wire “I” from module. Place a grounded wire about 5 mm away
from “I” terminal on module. Place ON/OFF rocker switch or wall
switch in ON position. If there is no spark at “I” terminal module must
be replaced. If there is a spark at “I” terminal, module is fine. Inspect
pilot assembly for shorted sparker wire or cracked insulator around
electrode. Replace pilot if necessary.
2. Pilot won’t light,
there is no noise or
spark.
a. No power or transformer installed
incorrectly.
Verify that transformer is installed and plugged into module. Check
voltage of transformer under load at spade connection on module
with ON/OFF switch in ON position. Acceptable readings of a good
transformer are between 6.4 and 6.6 volts AC.
b. A shorted or loose connection in wir- Remove and reinstall the wiring harness that plugs into module.
ing configuration or wiring harness. Verify there is a tight fit. Verify pilot assembly wiring to module. Re-
move and verify continuity of each wire in wiring harness. Replace
any damaged components.
c. Improper wall switch wiring.
d. Module not grounded.
Verify that 230 VAC power is “ON” to junction cord.
Verify black ground wire from module wire harness is grounded to
metal chassis of appliance.
e. Module.
Turn ON/OFF rocker switch or wall switch to OFF position. Remove
ignitor wire “I” from module. Place ON/OFF rocker switch or wall
switch in ON position. If there is no spark at “I” terminal module
must be replaced. If there is a spark at “I” terminal, module is fine.
Inspect pilot assembly for shorted sparker wire or cracked insulator
around electrode.
3. Pilot sparks, but
Pilot will not light.
a. Gas supply.
Verify that incoming gas line ball valve is “open”. Verify that inlet
pressure reading is within acceptable limits, inlet pressure must not
be exceeded.
b. Ignitor gap is incorrect.
c. Module is not grounded.
Verify that spark gap from ignitor to pilot hood is 3 mm.
Verify module is securely grounded to metal chassis of appliance.
d. Module voltage output / Valve/Pilot Verify battery voltage is at least 5.7 volts. Replace batteries if volt-
solenoid ohms readings. age is below 5.7.
52
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
IntelliFire Plus™ Ignition System - (continued)
Symptom
Possible Cause
Corrective Action
a. A shorted or loose connection in flame
sensing rod.
Verify all connections to wiring diagram in manual. Verify
connections underneath pilot assembly are tight. Verify con-
nections are not grounding out to metal chassis, pilot burn-
er, pilot enclosure or screen if present, or any other metal
object.
4. Pilot lights but contin-
ues to spark, and main
burner will not ignite.
(If the pilot continues
to spark after the
pilot flame has been lit,
flame rectification has
not occurred.)
b. Poor flame rectification or contaminated With fixed glass assembly in place, verify that flame is en-
flame sensing rod.
gulfing flame sensing rod on left side of pilot hood. Flame
sensing rod should glow shortly after ignition. Verify cor-
rect pilot orifice is installed and gas inlet is set to pressure
specifications. Polish flame sensing rod with fine steel wool
to remove any contaminants that may have accumulated on
flame sensing rod.
c. Module is not grounded.
Verify module is securely grounded to metal chassis of ap-
pliance. Verify that wire harness is firmly connected to the
module.
d. Damaged pilot assembly or contami-
nated flame sensing rod.
Verify that ceramic insulator around the flame sensing rod
is not cracked, damaged, or loose. Verify connection from
flame sensing rod to white sensor wire. Polish flame sens-
ing rod with fine steel wool to remove any contaminants
that may have accumulated on flame sensing rod. Verify
continuity with a multimeter with ohms set at lowest range.
Replace pilot if any damage is detected.
e. Module.
Turn ON/OFF rocker switch or wall switch to OFF position.
Remove ignitor wire “I” from module. Place ON/OFF rocker
switch or wall switch in ON position. If there is no spark at “I”
terminal module must be replaced. If there is a spark at “I”
terminal, module is fine.
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
53
Component Access
16
WARNING! Risk of Fire, Electric Shock and Burns!
Turn off power to module and valve by unplugging the 6V
transformer from the junction cord and remove batteries
from battery tray (if installed), before removing fixed glass
assembly.
D. Media Tray Removal
1. Remove decorative front and fixed glass assembly.
2. Remove media tray by removing three screw located
on the front edge of the media tray. See Figure 16.3.
A. Decorative Front and Fixed Glass Assem-
bly Removal
• The decorative front can be removed by unscrewing (4)
screws that secure the decorative front to the fireplace.
Refer to the installation instructions that were included
with the decorative front option for more detailed
instruction.
• Refer to Section 14.E for fixed glass removal and
installation instructions.
B. Valve Pressure Taps
The pressure taps are available through the front of the
appliance. The decorative mesh front and fireplace gas
assembly must be removed to gain access to the pres-
sure taps.
REMOVE SCREWS
Figure 16.3 Remove Media Tray
E. Burner and Base Pan Removal
Once the media tray is removed, the burner assembly
and base pan may be removed.
INLET
1. Remove burner assembly by removing two screws that
secure the burner to the pilot assembly bracket and
remove the one screw that secures the burner clip that
secures the burner to the base pan. See Figure 16.4.
MANIFOLD OUTLET
Figure 16.1 Pressure Taps
C. Control Module Access
2. Once the burner is removed, the base pan can be
removed by lifting “up” and “out”.
The control module on this appliance can be accessed by
following the following steps:
1. Remove decorative front and fixed glass assembly.
2. Locate the control module. See Figure 16.2.
3. Unplug the black wire from the transformer, unplug the
wire harness to the valve, and unplug the orange and
white wires from the pilot assembly.
REMOVE SCREWS
BURNER CLIP
4. Verify the replacement module is installed to the wire
diagram listed in Section 12.
ON/OFF/REMOTE
SWITCH
GAS VALVE
BASE PAN
Figure 16.4 Remove Burner Assembly
CONTROL
MODULE
BATTERY
PACK
DC ADAPTER
Figure 16.2 Valve Components
54
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
F. Access Through the Valve Assembly
The lower access cover panel is removable if finishing
material has not been previously installed.
Remove media tray, burner assembly, and base pan.
To access components:
1. Remove eleven screws around perimeter of valve as-
sembly that secure valve plate to the firebox bottom.
See Figure 16.5.
2. Lift the valve assembly from the back so that the gas
valve can clear the valve plate hole in the bottom the
firebox. See Figure 16.6.
Figure 16.7 Disconnect Gas Valve
Figure 16.5 Remove Valve Plate Screws
3. Set the valve bracket on the front lip of the firebox bot-
tom. Turn “off” the ball valve. Disconnect gas valve
from the gas flex ball valve assembly at the pressure
fitting. See Figure 16.7.
VALVE ASSEMBLY
GASKET
Figure 16.6 Remove Valve Plate
4. Lift the valve assembly up and out to make necessary
service or repair.
5. Replace gasket before reinstalling the valve assem-
bly.
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
55
G. Gas Valve Replacement
H. Pilot Assembly Replacement
Once the valve assembly has been removed, the gas
valve, pilot assembly, orifice flex tube, and flex ball valve
can be replaced.
PILOT
BRACKET
Figure 16.10
1. Disconnect the orange and white wires from the con-
trol module
2. Remove the pilot fitting from the valve assembly
3. Remove two screws that secure pilot assembly to the
pilot bracket
Figure 16.8
1. Place the valve assembly on a clean, stable surface to
service or replace any components.
2. Disconnect the orange and green wires from the
valve.
3. Removed the Pilot fitting from the valve assembly
4. Disconnect the orifice gas flex and gas ball valve flex
from the (2) flare fittings.
5. Unscrew (2) screws located under the pressure taps
to remove the gas valve from the valve bracket.
PILOT
VALVE
FITTING
BRACKET
GAS BALL
VALVE
GAS
VALVE
ORIFICE
FLEX
FLARE FITTING
Figure 16.9
56
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Materials
17
A. Appliance Dimension Diagram
Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 5.
2,54 cm STANDOFF
K
L
J
S
R
M
I
N
Ø
C
NON-COMBUSTIBLE ZONE
(PROVIDED WITH UNIT)
GAS LINE
ACCESS
O
H
E
D
T
F
P
U
ELECTRICAL
ACCESS
B
A
G
Q
LEFT VIEW
FRONT VIEW
RIGHT VIEW
Location Centimeters
Location Centimeters
K
L
2,5
95,9
40
A
B
C
D
E
F
G
H
I
121,8
109,2
99,3
33,7
100,6
9
M
N
O
P
Q
R
S
T
16,8
106
5,5
15,2
43,8
46,4
65,7
24,8
17,4
119,5
23,7
42,5
J
U
Figure 17.1 Appliance Dimensions
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
57
B. Vent Components Diagrams
24,1 cm
35,2 cm
29,5 cm
30,8 cm
356 cm
18,1 cm
DRC-RADIUS
Cap Shield
14,6 cm
COOL-ADD
Cap Shield
30,2 cm
12,7 cm
35,2 cm
DVP-BEK2
DVP-HPC Cap Brick Extension
Figure 17.2 Vent Components
58
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Vent Components Diagrams (continued)
16,5 cm
16,5 cm
16,5 cm
22,2 cm
23,5 cm
15,2 cm
16,8 cm
16,8 cm
SLP-45 - 45° Elbow
25,1 cm
SLP90- 90° Elbow
Effective Height/Length
Pipe
SLP4
cm
10,2
15,2
30,5
61
mm
Effective
Height/
Length
102
152
66,0 cm
SLP6
SLP12
SLP24
SLP36
SLP48
SLP6A
SLP12A
305
610
91,4
121,9
5 - 15
5 - 30
914
1219
51-152
51-305
DVP-HSM-B
Extended Heat Shield
SLP-PIPE
SLP-FS
SLP-WS
SLP-HVS
Ceiling Firestop
Wall Shield Firestop
Horizontal Pipe
Support
Figure 17.3 SLP Series Vent Components
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
59
B. Vent Components Diagrams (continued)
SLP-TVHW
Vertical
Termination Cap
SLP-CCS-BK
Cathedral Ceiling
Support Box-Black
SLK-SNKD
Snorkel
Termination Cap
SLP-DCF-BK
SLP-WT-BK
SL-2DVP
Ceiling Firestop
Black
Wall Thimble-Black
Adapter
30,5 cm
17,8 cm
39,4 cm
DVP-FBHT
SLP90
SL-2DVP
DVP-FBHT
Figure 17.4 SLP Series Vent Components
60
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Vent Components Diagrams (continued)
Note: Heat shields MUST overlap by a minimum of 3,8 cm. The heat shield is designed to be used on a
wall 10,2 cm to 18,4 cm thick. If wall thickness is less than 10,2 cm the existing heat shields must be
field tricmed. If wall thickness is greater than 18,4 cm a DVP-HSM-B will be required.
20,3 cm
Heat
Shield
38,4 cm
Minimum
Effective Length
Maximum
Effective Length
Term Cap
Max
Effective
Length
Trap1
Trap2
7.9 cm
12,1cm
30,5 cm
13,3 cm
23,5 cm
SLP-TRAP
Horizontal Termination Cap
Effective Length
14,6 to 21,3 cm
33,0 cm
20,6 cm
14,0 cm
21,3 cm
3°
87°
38,1 cm
26,7 cm
27,6 cm
SLP-HRC-SS
SLP-HRC-ZC-SS
HORIZONTAL TERMINATION CAP
Figure 17.5 SLP Series Vent Components
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
61
XLR-N-CE, XLR-PB-CE
C. Service Parts
Landscape DV Appliance
Beginning Manufacturing Date: March 2010
Ending Manufacturing Date: ______
1
3
4
2
5
6
7
9
8
10
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your appliance please
provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer.
ITEM
DESCRIPTION
COMMENTS
PART NUMBER
2184-147
2264-103
2184-102
2198-405
2198-114
2184-007
2198-007
2198-115
GLA-SLR
2166-374
2118-170
1
2
3
4
5
Sheet Rock Ledge
Lower Cover Panel
Top Panel Finishing Edge
Non Combustible Board
Media Tray
Burner N
6
Burner P & B
7
8
Base Pan
Glass Door Assembly
Junction Cord
9
10
Thermostat Wire
Additional service part numbers appear on following page.
62
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
XLR-N-CE, XLR-PB-CE
Service Parts
Beginning Manufacturing Date: March 2010
Ending Manufacturing Date: ______
14.1
#14 Valve Assembly
14.2
14.3
14.4
14.5
14.6
14.7
14.12
14.8
14.9
14.11
14.10
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your appliance please
provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer.
ITEM
DESCRIPTION
COMMENTS
PART NUMBER
2184-123
2090-012
2090-013
2198-174
2118-420
383-302A
303-315/5
2198-153
2166-308
2166-309
2166-304
2166-306
2098-320A
2166-305
582-842
14.1
Pilot Shield
Pilot Assembly N
Pilot Assembly P & B
Pilot Bracket
14.2
14.3
14.4
14.5
14.6
14.7
3-Hole Grommet
Bulkhead W/Flex Tube
Male Connector
Valve Bracket
Pkg of 5
Valve N
14.8
Valve P & B
14.9
14.10
14.11
14.12
Module Wire Assembly
Module
Flex Ball Valve Assembly
Power Supply
Orifice N (#42C)
Orifice B (#55C)
Orifice P (.057C)
582-855
582-057
Additional service part numbers appear on following page.
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
63
C. Service Parts List
XLR-N-CE, XLR-PB-CE
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your appliance please
provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer.
ITEM
DESCRIPTION
COMMENTS
PART NUMBER
2166-323
Battery Pack
2143-168
Elbow Heat Shield
Exhaust Restrictor
Gasket Assembly
530-299
2113-080
Contains burner neck, shutter bracket, vent, seal cap, valve plate,
and air passage gaskets
Pkg of 2
33858/2
Glass Latch Assembly
Heat Shield, Inner
Jumper Wire, Wall Switch
Nailing Tabs
2198-130
2179-300
2198-132
2206-299
2264-060
TUP-GBK-12
WSK-21-W
2187-198
2201-030
Rocker Switch
Switch Assembly, Reset
Touch Up Paint
Wall Switch Kit
Wire, Jumper
Wire Assembly, Module Reset
PB2N-XLR-CE
P2B-XLR-CE
N2PB-XLR-CE
593-528
Conversion Kit N
Conversion Kit B
Conversion Kit P
Pilot Orifice N
Pilot Orifice B
593-529
Pilot Orifice P
593-527
Regulator N
NGK-DXF-NP
LPK-DXF-NP
Regulator P & B
64
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
D. Contact Information
Heat & Glo, a brand of Hearth & Home Technologies Inc.
7571 215th Street West, Lakeville, MN 55044
Please contact your Heat & Glo dealer with any questions or concerns.
For the location of your nearest Heat & Glo dealer,
- NOTES -
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
NOTICE
DO NOT DISCARD THIS MANUAL
• Important operating
and maintenance
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
• Leave this manual with
party responsible for use
and operation.
This product may be covered by one or more of the following patents: (United States) 5328356, 5601073, 5613487,
5647340, 5890485, 5941237, 5947112, 5996575, 6006743, 6019099, 6053165, 6145502, 6170481, 6374822, 6484712,
6601579, 6769426, 6863064, 7077122, 7098269, 7258116, 7470729 or other U.S. and foreign patents pending.
2000-945
Printed in U.S.A. - Copyright 2012
Heat & Glo • XLR-N-CE, XLR-PB-CE • 2198-900 Rev. J • 5/12
Download from Www.Somanuals.com. All Manuals Search And Download.
65
|
Grizzly Biscuit Joiner G1182HW User Manual
Grizzly Router T10432 User Manual
H2O Audio Headphones SV iP4G User Manual
Hamilton Beach Kitchen Grill 840135600 User Manual
Hasbro Games GI Joe Voice FX Duke User Manual
Healthrider Treadmill HRT12920 User Manual
Hotpoint Washer WM82 User Manual
HP Hewlett Packard Yard Vacuum 436853 001 User Manual
Husqvarna Lawn Mower 1030 BioClip User Manual
iLive MP3 Docking Station IT209B User Manual