Para obtener un ejemplar en Español de este
Pour demander un exemplaire en français de ce Manuel
Owner’s Manual
Installation and Operation
Model:
Escape-42DV
Escape-42DVLP
NOTICE
DO NOT DISCARD THIS MANUAL
• Important operating
and maintenance
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
• Leave this manual with
party responsible for use
and operation.
WARNING
WARNING: If the information in these
instructions is not followed exactly, a fire
or explosion may result causing property
damage, personal injury, or death.
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
Hot glass will cause burns.
• DO NOT touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• DO NOT store or use gasoline or other flam-
mable vapors and liquids in the vicinity of this
or any other appliance.
• CAREFULLY SUPERVISE children in same room as
fireplace.
• Alert children and adults to hazards of high temperatures.
• What to do if you smell gas
- DO NOT try to light any appliance.
High temperatures may ignite clothing or other flammable
materials.
• Keep clothing, furniture, draperies and other flammable
materials away.
- DO NOT touch any electrical switch. DO
NOT use any phone in your building.
- Immediately call your gas supplier from a
neighbor’s phone. Follow the gas suppli-
er’s instructions.
This appliance has been supplied with an integral barrier
to prevent direct contact with the fixed glass panel. DO
NOT operate the appliance with the barrier removed.
- If you cannot reach your gas supplier, call
the fire department.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
• Installation and service must be performed
by a qualified installer, service agency, or the
gas supplier.
In the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas fitter.
See Table of Contents for location of additional Commonwealth
of Massachusetts requirements.
This appliance may be installed as an OEM installation in
manufactured home (USA only) or mobile home and must be
installed in accordance with the manufacturer’s instructions
and the manufactured home construction and safety standard,
Title 24 CFR, Part 3280 or Standard for Installation in Mobile
Homes, CAN/CSA Z240MH, in Canada.
Installation and service of this appliance should be
performed by qualified personnel. Hearth & Home
Technologies suggests NFI certified or factory trained
professionals, or technicians supervised by an NFI
certified professional.
This appliance is only for use with the type(s) of gas indicated
on the rating plate.
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Safety Alert Key:
• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.
• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
• NOTICE: Used to address practices not related to personal injury.
Table of Contents
A. Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
B. Limited Lifetime Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . 5
6 Termination Locations
A. Vent Termination Minimum Clearances . . . . . . . . . . . . . . 22
1 Listing and Code Approvals
7 Vent Information and Diagrams
A. Appliance Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
B. Glass Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
C. BTU Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
D. High Altitude Installations. . . . . . . . . . . . . . . . . . . . . . . . . . 7
E. Non-Combustible Materials Specification. . . . . . . . . . . . . . 7
F. Combustible Materials Specification . . . . . . . . . . . . . . . . . 7
G. Electrical Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
H. Requirements for the Commonwealth of Massachusetts. . 8
A. Approved Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
B. Vent Table Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
C. Use of Elbows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
D. Measuring Standards. . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
E. Vent Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
8 Vent Clearances and Framing
A. Pipe Clearances to Combustibles . . . . . . . . . . . . . . . . . . 29
B. Wall Penetration Framing. . . . . . . . . . . . . . . . . . . . . . . . . 29
C. Install the Ceiling Firestop . . . . . . . . . . . . . . . . . . . . . . . . 30
D. Install Attic Insulation Shield. . . . . . . . . . . . . . . . . . . . . . . 31
E. Installing the Optional Heat-Zone® Gas Kit . . . . . . . . . . . 31
User Guide
2 Operating Instructions
A. Gas Fireplace Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
B. Your Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
C. Clear Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
D. Decorative Doors and Fronts . . . . . . . . . . . . . . . . . . . . . . 10
E. Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
F. Wall Controls and Wall Switches . . . . . . . . . . . . . . . . . . . 10
G. Before Lighting Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . 10
H. Lighting Instructions (IPI) . . . . . . . . . . . . . . . . . . . . . . . . . 11
I. After Fireplace is Lit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
J. Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . 12
9 Appliance Preparation
A. Removing Non-combustible Facing Material Assembly. . 32
B. Securing and Leveling the Appliance. . . . . . . . . . . . . . . . 32
C. Installing Non-combustible Facing Material . . . . . . . . . . . 33
10 Installing Vent Pipe
A. Assemble Vent Sections. . . . . . . . . . . . . . . . . . . . . . . . . . 34
B. Assemble Slip Sections . . . . . . . . . . . . . . . . . . . . . . . . . . 35
C. Secure the Vent Sections. . . . . . . . . . . . . . . . . . . . . . . . . 35
D. Disassemble Vent Sections . . . . . . . . . . . . . . . . . . . . . . . 36
E. Install Metal Roof Flashing. . . . . . . . . . . . . . . . . . . . . . . . 37
F. Assemble and Install Storm Collar. . . . . . . . . . . . . . . . . . 37
G. Install Vertical Termination Cap . . . . . . . . . . . . . . . . . . . . 38
H. Heat Shield Requirements for Horizontal Termination . . . 38
I. Install Horizontal Termination Cap . . . . . . . . . . . . . . . . . . 39
3 Maintenance and Service
A. Maintenance Tasks-Homeowner . . . . . . . . . . . . . . . . . . . 13
B. Maintenance Tasks-Qualified Service Technician . . . . . . 14
Installer Guide
4 Getting Started
11 Gas Information
A. Typical Appliance System. . . . . . . . . . . . . . . . . . . . . . . . . 16
B. Design and Installation Considerations . . . . . . . . . . . . . . 17
C. Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . . . 17
D. Inspect Appliance and Components. . . . . . . . . . . . . . . . . 17
A. Fuel Conversion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
B. Gas Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
C. Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
D. High Altitude Installations. . . . . . . . . . . . . . . . . . . . . . . . . 40
5 Framing and Clearances
12 Electrical Information
A. Selecting Appliance Location . . . . . . . . . . . . . . . . . . . . . . 18
B. Constructing the Appliance Chase. . . . . . . . . . . . . . . . . . 19
C. Clearances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
D. Mantel and Wall Projections. . . . . . . . . . . . . . . . . . . . . . . 20
E. Hearth Extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
A. Wiring Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
B. IntelliFire Ignition System Wiring . . . . . . . . . . . . . . . . . . . 41
C. Optional Accessories Requirements . . . . . . . . . . . . . . . . 41
D. Electrical Service and Repair. . . . . . . . . . . . . . . . . . . . . . 43
E. Junction Box Installation. . . . . . . . . . . . . . . . . . . . . . . . . . 43
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
3
13 Finishing
A. Splatter Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
B. Mantel and Wall Projections. . . . . . . . . . . . . . . . . . . . . . . 45
C. Facing Material. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
D. Finishing Materials Requirements . . . . . . . . . . . . . . . . . . 46
14 Appliance Setup
A. Remove Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . 47
B. Remove the Shipping Materials . . . . . . . . . . . . . . . . . . . . 47
C. Clean the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
D. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
E. Ember Placement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
F. Install the Log Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . 48
G. Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
H. Install the Mesh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
I. Air Shutter Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
15 Troubleshooting
A. IntelliFire Ignition System. . . . . . . . . . . . . . . . . . . . . . . . . 53
16 Reference Materials
A. Appliance Dimension Diagram. . . . . . . . . . . . . . . . . . . . . 55
B. Vent Components Diagrams . . . . . . . . . . . . . . . . . . . . . . 56
C. Service Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
D. Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
= Contains updated information.
4
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Limited Lifetime Warranty
Hearth & Home Technologies Inc.
LIMITED LIFETIME WARRANTY
Hearth & Home Technologies Inc., on behalf of its hearth brands (”HHT”), extends the following warranty for
HHT gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer.
WARRANTY COVERAGE:
HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking ownership
of the appliance at the site of installation within two years following the date of original purchase, that the HHT appliance
will be free from defects in materials and workmanship at the time of manufacture. After installation, if covered compo-
nents manufactured by HHT are found to be defective in materials or workmanship during the applicable warranty period,
HHT will, at its option, repair or replace the covered components. HHT, at its own discretion, may fully discharge all of its
obligations under such warranties by replacing the product itself or refunding the verified purchase price of the product
itself. The maximum amount recoverable under this warranty is limited to the purchase price of the product. This warranty
is subject to conditions, exclusions and limitations as described below.
WARRANTY PERIOD:
Warranty coverage begins on the date of original purchase. In the case of new home construction, warranty coverage
begins on the date of first occupancy of the dwelling or six months after the sale of the product by an independent,
authorized HHT dealer/ distributor, whichever occurs earlier. The warranty shall commence no later than 24 months
following the date of product shipment from HHT, regardless of the installation or occupancy date. The warranty period for
parts and labor for covered components is produced in the following table.
The term “Limited Lifetime” in the table below is defined as: 20 years from the beginning date of warranty coverage for
gas appliances, and 10 years from the beginning date of warranty coverage for wood, pellet, and coal appliances. These
time periods reflect the minimum expected useful lives of the designated components under normal operating conditions.
Warranty Period
Parts Labor
HHT Manufactured Appliances and Venting
EPA
Components Covered
Gas
X
Wood Pellet
Coal Electric Venting
Wood
All parts and material except as
covered by Conditions,
Exclusions, and Limitations
listed
1 Year
X
X
X
X
X
X
Igniters, electronic components,
and glass
X
X
X
X
X
X
2 years
X
X
X
Factory-installed blowers
Molded refractory panels
3 years
X
X
Firepots and burnpots
Castings and baffles
5 years 1 year
X
X
Manifold tubes,
HHT chimney and termination
7 years 3 years
X
X
10
1 year
years
X
X
X
Burners, logs and refractory
Firebox and heat exchanger
Limited
3 years
Lifetime
X
X
X
X
X
X
X
X
All replacement parts
beyond warranty period
90 Days
X
X
See conditions, exclusions, and limitations on next page.
4021-645C 12-29-10
Page 1 of 2
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
5
B. Limited Lifetime Warranty (continued)
WARRANTY CONDITIONS:
‡ꢀ 7KLVꢀZDUUDQW\ꢀRQO\ꢀFRYHUVꢀ++7ꢀDSSOLDQFHVꢀWKDWꢀDUHꢀSXUFKDVHGꢀWKURXJKꢀDQꢀ++7ꢀDXWKRUL]HGꢀGHDOHUꢀRUꢀGLVWULEXWRUꢁꢀ$ꢀOLVWꢀRIꢀ
++7ꢀDXWKRUL]HGꢀGHDOHUVꢀLVꢀDYDLODEOHꢀRQꢀWKHꢀ++7ꢀEUDQGHGꢀZHEVLWHVꢁ
‡ꢀ 7KLVꢀZDUUDQW\ꢀLVꢀRQO\ꢀYDOLGꢀZKLOHꢀWKHꢀ++7ꢀDSSOLDQFHꢀUHPDLQVꢀDWꢀWKHꢀVLWHꢀRIꢀRULJLQDOꢀLQVWDOODWLRQꢁ
‡ꢀ &RQWDFWꢀ\RXUꢀLQVWDOOLQJꢀGHDOHUꢀIRUꢀZDUUDQW\ꢀVHUYLFHꢁꢀ,IꢀWKHꢀLQVWDOOLQJꢀGHDOHUꢀLVꢀXQDEOHꢀWRꢀSURYLGHꢀQHFHVVDU\ꢀSDUWVꢂꢀFRQWDFWꢀ
WKHꢀQHDUHVWꢀ++7ꢀDXWKRUL]HGꢀGHDOHUꢀRUꢀVXSSOLHUꢁꢀ$GGLWLRQDOꢀVHUYLFHꢀIHHVꢀPD\ꢀDSSO\ꢀLIꢀ\RXꢀDUHꢀVHHNLQJꢀZDUUDQW\ꢀVHUYLFHꢀ
IURPꢀDꢀGHDOHUꢀRWKHUꢀWKDQꢀWKHꢀGHDOHUꢀIURPꢀZKRPꢀ\RXꢀRULJLQDOO\ꢀSXUFKDVHGꢀWKHꢀSURGXFWꢁ
‡ꢀ &KHFNꢀZLWKꢀ\RXUꢀGHDOHUꢀLQꢀDGYDQFHꢀIRUꢀDQ\ꢀFRVWVꢀWRꢀ\RXꢀZKHQꢀDUUDQJLQJꢀDꢀZDUUDQW\ꢀFDOOꢁꢀ7UDYHOꢀDQGꢀVKLSSLQJꢀFKDUJHVꢀ
IRUꢀSDUWVꢀDUHꢀQRWꢀFRYHUHGꢀE\ꢀWKLVꢀZDUUDQW\ꢁ
WARRANTY EXCLUSIONS:
7KLVꢀZDUUDQW\ꢀGRHVꢀQRWꢀFRYHUꢀWKHꢀIROORZLQJꢅ
‡ꢀ &KDQJHVꢀLQꢀVXUIDFHꢀILQLVKHVꢀDVꢀDꢀUHVXOWꢀRIꢀQRUPDOꢀXVHꢁꢀ$VꢀDꢀKHDWLQJꢀDSSOLDQFHꢂꢀVRPHꢀFKDQJHVꢀLQꢀFRORUꢀRIꢀLQWHULRUꢀDQGꢀ
H[WHULRUꢀVXUIDFHꢀILQLVKHVꢀPD\ꢀRFFXUꢁꢀ7KLVꢀLVꢀQRWꢀDꢀIODZꢀDQGꢀLVꢀQRWꢀFRYHUHGꢀXQGHUꢀZDUUDQW\ꢁ
‡ꢀ 'DPDJHꢀWRꢀSULQWHGꢂꢀSODWHGꢂꢀRUꢀHQDPHOHGꢀVXUIDFHVꢀFDXVHGꢀE\ꢀILQJHUSULQWVꢂꢀDFFLGHQWVꢂꢀPLVXVHꢂꢀVFUDWFKHVꢂꢀPHOWHGꢀLWHPVꢂꢀ
RUꢀRWKHUꢀH[WHUQDOꢀVRXUFHVꢀDQGꢀUHVLGXHVꢀOHIWꢀRQꢀWKHꢀSODWHGꢀVXUIDFHVꢀIURPꢀWKHꢀXVHꢀRIꢀDEUDVLYHꢀFOHDQHUVꢀRUꢀSROLVKHVꢁ
‡ꢀ 5HSDLUꢀRUꢀUHSODFHPHQWꢀRIꢀSDUWVꢀWKDWꢀDUHꢀVXEMHFWꢀWRꢀQRUPDOꢀZHDUꢀDQGꢀWHDUꢀGXULQJꢀWKHꢀZDUUDQW\ꢀSHULRGꢁꢀ7KHVHꢀSDUWVꢀ
LQFOXGHꢅꢀSDLQWꢂꢀZRRGꢂꢀSHOOHWꢀDQGꢀFRDOꢀJDVNHWVꢂꢀILUHEULFNVꢂꢀJUDWHVꢂꢀIODPHꢀꢀJXLGHVꢂꢀOLJKWꢀEXOEVꢂꢀEDWWHULHVꢀDQGꢀWKHꢀGLVFRORU-
DWLRQꢀRIꢀJODVVꢁ
‡ꢀ 0LQRUꢀH[SDQVLRQꢂꢀFRQWUDFWLRQꢂꢀRUꢀPRYHPHQWꢀRIꢀFHUWDLQꢀSDUWVꢀFDXVLQJꢀQRLVHꢁꢀ7KHVHꢀFRQGLWLRQVꢀDUHꢀQRUPDOꢀDQGꢀFRP-
SODLQWVꢀUHODWHGꢀWRꢀWKLVꢀQRLVHꢀDUHꢀQRWꢀFRYHUHGꢀE\ꢀWKLVꢀZDUUDQW\ꢁ
‡ꢀ 'DPDJHVꢀUHVXOWLQJꢀIURPꢅꢀꢆꢇꢈꢀIDLOXUHꢀWRꢀLQVWDOOꢂꢀRSHUDWHꢂꢀRUꢀPDLQWDLQꢀWKHꢀDSSOLDQFHꢀLQꢀDFFRUGDQFHꢀZLWKꢀWKHꢀLQVWDOODWLRQꢀ
LQVWUXFWLRQVꢂꢀRSHUDWLQJꢀLQVWUXFWLRQVꢂꢀDQGꢀOLVWLQJꢀDJHQWꢀLGHQWLILFDWLRQꢀODEHOꢀIXUQLVKHGꢀZLWKꢀWKHꢀDSSOLDQFHꢄꢀꢆꢉꢈꢀIDLOXUHꢀWRꢀ
LQVWDOOꢀWKHꢀDSSOLDQFHꢀLQꢀDFFRUGDQFHꢀZLWKꢀORFDOꢀEXLOGLQJꢀFRGHVꢄꢀꢆꢊꢈꢀVKLSSLQJꢀRUꢀLPSURSHUꢀKDQGOLQJꢄꢀꢆꢋꢈꢀLPSURSHUꢀRSHUD-
WLRQꢂꢀDEXVHꢂꢀPLVXVHꢂꢀFRQWLQXHGꢀRSHUDWLRQꢀZLWKꢀGDPDJHGꢂꢀFRUURGHGꢀRUꢀIDLOHGꢀFRPSRQHQWVꢂꢀDFFLGHQWꢂꢀRUꢀLPSURSHUO\ꢌꢀ
LQFRUUHFWO\ꢀSHUIRUPHGꢀUHSDLUVꢄꢀꢆꢍꢈꢀHQYLURQPHQWDOꢀFRQGLWLRQVꢂꢀLQDGHTXDWHꢀYHQWLODWLRQꢂꢀQHJDWLYHꢀSUHVVXUHꢂꢀRUꢀGUDIWLQJꢀ
FDXVHGꢀE\ꢀWLJKWO\ꢀVHDOHGꢀFRQVWUXFWLRQVꢂꢀLQVXIILFLHQWꢀPDNHꢃXSꢀDLUꢀVXSSO\ꢂꢀRUꢀKDQGOLQJꢀGHYLFHVꢀVXFKꢀDVꢀH[KDXVWꢀIDQVꢀRUꢀ
IRUFHGꢀDLUꢀIXUQDFHVꢀRUꢀRWKHUꢀVXFKꢀFDXVHVꢄꢀꢆꢎꢈꢀXVHꢀRIꢀIXHOVꢀRWKHUꢀWKDQꢀWKRVHꢀVSHFLILHGꢀLQꢀWKHꢀRSHUDWLQJꢀLQVWUXFWLRQVꢄꢀꢆꢏꢈꢀ
LQVWDOODWLRQꢀRUꢀXVHꢀRIꢀFRPSRQHQWVꢀQRWꢀVXSSOLHGꢀZLWKꢀWKHꢀDSSOLDQFHꢀRUꢀDQ\ꢀRWKHUꢀFRPSRQHQWVꢀQRWꢀH[SUHVVO\ꢀDXWKRUL]HGꢀ
DQGꢀDSSURYHGꢀE\ꢀ++7ꢄꢀꢆꢐꢈꢀPRGLILFDWLRQꢀRIꢀWKHꢀDSSOLDQFHꢀQRWꢀH[SUHVVO\ꢀDXWKRUL]HGꢀDQGꢀDSSURYHGꢀE\ꢀ++7ꢀLQꢀZULWLQJꢄꢀ
DQGꢌRUꢀꢆꢑꢈꢀLQWHUUXSWLRQVꢀRUꢀIOXFWXDWLRQVꢀRIꢀHOHFWULFDOꢀSRZHUꢀVXSSO\ꢀWRꢀWKHꢀDSSOLDQFHꢁ
‡ꢀ 1RQꢃ++7ꢀYHQWLQJꢀFRPSRQHQWVꢂꢀKHDUWKꢀFRPSRQHQWVꢀRUꢀRWKHUꢀDFFHVVRULHVꢀXVHGꢀLQꢀFRQMXQFWLRQꢀZLWKꢀWKHꢀDSSOLDQFHꢁ
‡ꢀ $Q\ꢀSDUWꢀRIꢀDꢀSUHꢃH[LVWLQJꢀILUHSODFHꢀV\VWHPꢀLQꢀZKLFKꢀDQꢀLQVHUWꢀRUꢀDꢀGHFRUDWLYHꢀJDVꢀDSSOLDQFHꢀLVꢀLQVWDOOHGꢁ
‡ꢀ ++7¶VꢀREOLJDWLRQꢀXQGHUꢀWKLVꢀZDUUDQW\ꢀGRHVꢀQRWꢀH[WHQGꢀWRꢀWKHꢀDSSOLDQFH¶VꢀFDSDELOLW\ꢀWRꢀKHDWꢀWKHꢀGHVLUHGꢀVSDFHꢁꢀ,QIRUPD-
WLRQꢀLVꢀSURYLGHGꢀWRꢀDVVLVWꢀWKHꢀFRQVXPHUꢀDQGꢀWKHꢀGHDOHUꢀLQꢀVHOHFWLQJꢀWKHꢀSURSHUꢀDSSOLDQFHꢀIRUꢀWKHꢀDSSOLFDWLRQꢁꢀ&RQVLGHU-
DWLRQꢀPXVWꢀEHꢀJLYHQꢀWRꢀDSSOLDQFHꢀORFDWLRQꢀDQGꢀFRQILJXUDWLRQꢂꢀHQYLURQPHQWDOꢀFRQGLWLRQVꢂꢀLQVXODWLRQꢀDQGꢀDLUꢀWLJKWQHVVꢀRIꢀ
ꢀWKHꢀVWUXFWXUHꢁ
This warranty is void if:
‡ꢀ 7KHꢀDSSOLDQFHꢀKDVꢀEHHQꢀRYHUꢃILUHGꢀRUꢀRSHUDWHGꢀLQꢀDWPRVSKHUHVꢀFRQWDPLQDWHGꢀE\ꢀFKORULQHꢂꢀIOXRULQHꢂꢀRUꢀRWKHUꢀGDPDJLQJꢀ
FKHPLFDOVꢁꢀ2YHUꢃILULQJꢀFDQꢀEHꢀLGHQWLILHGꢀE\ꢂꢀEXWꢀQRWꢀOLPLWHGꢀWRꢂꢀZDUSHGꢀSODWHVꢀRUꢀWXEHVꢂꢀUXVWꢀFRORUHGꢀFDVWꢀLURQꢂꢀEXEEOLQJꢂꢀ
FUDFNLQJꢀDQGꢀGLVFRORUDWLRQꢀRIꢀVWHHOꢀRUꢀHQDPHOꢀILQLVKHVꢁ
‡ꢀ 7KHꢀDSSOLDQFHꢀLVꢀVXEMHFWHGꢀWRꢀSURORQJHGꢀSHULRGVꢀRIꢀGDPSQHVVꢀRUꢀFRQGHQVDWLRQꢁ
‡ꢀ 7KHUHꢀLVꢀDQ\ꢀGDPDJHꢀWRꢀWKHꢀDSSOLDQFHꢀRUꢀRWKHUꢀFRPSRQHQWVꢀGXHꢀWRꢀZDWHUꢀRUꢀZHDWKHUꢀGDPDJHꢀZKLFKꢀLVꢀWKHꢀUHVXOWꢀRIꢂꢀEXWꢀ
QRWꢀOLPLWHGꢀWRꢂꢀLPSURSHUꢀFKLPQH\ꢀRUꢀYHQWLQJꢀLQVWDOODWLRQꢁꢀ
LIMITATIONS OF LIABILITY:
‡ꢀ 7KHꢀRZQHU¶VꢀH[FOXVLYHꢀUHPHG\ꢀDQGꢀ++7¶VꢀVROHꢀREOLJDWLRQꢀXQGHUꢀWKLVꢀZDUUDQW\ꢂꢀXQGHUꢀDQ\ꢀRWKHUꢀZDUUDQW\ꢂꢀH[SUHVVꢀRUꢀ
LPSOLHGꢂꢀRUꢀLQꢀFRQWUDFWꢂꢀWRUWꢀRUꢀRWKHUZLVHꢂꢀVKDOOꢀEHꢀOLPLWHGꢀWRꢀUHSODFHPHQWꢂꢀUHSDLUꢂꢀRUꢀUHIXQGꢂꢀDVꢀVSHFLILHGꢀDERYHꢁꢀ,QꢀQRꢀ
HYHQWꢀZLOOꢀ++7ꢀEHꢀOLDEOHꢀIRUꢀDQ\ꢀLQFLGHQWDOꢀRUꢀFRQVHTXHQWLDOꢀGDPDJHVꢀFDXVHGꢀE\ꢀGHIHFWVꢀLQꢀWKHꢀDSSOLDQFHꢁꢀ6RPHꢀVWDWHVꢀ
GRꢀQRWꢀDOORZꢀH[FOXVLRQVꢀRUꢀOLPLWDWLRQꢀRIꢀLQFLGHQWDOꢀRUꢀFRQVHTXHQWLDOꢀGDPDJHVꢂꢀVRꢀWKHVHꢀOLPLWDWLRQVꢀPD\ꢀQRWꢀDSSO\ꢀWRꢀ\RXꢁꢀ
7KLVꢀZDUUDQW\ꢀJLYHVꢀ\RXꢀVSHFLILFꢀULJKWVꢄꢀ\RXꢀPD\ꢀDOVRꢀKDYHꢀRWKHUꢀULJKWVꢂꢀZKLFKꢀYDU\ꢀIURPꢀVWDWHꢀWRꢀVWDWHꢁꢀ(;&(37ꢀ72ꢀ
7+(ꢀ(;7(17ꢀ3529,'('ꢀ%<ꢀ/$:ꢂꢀ++7ꢀ0$.(6ꢀ12ꢀ(;35(66ꢀ:$55$17,(6ꢀ27+(5ꢀ7+$1ꢀ7+(ꢀ:$55$17<ꢀ
63(&,),('ꢀ+(5(,1ꢁꢀ7+(ꢀ'85$7,21ꢀ2)ꢀ$1<ꢀ,03/,('ꢀ:$55$17<ꢀ,6ꢀ/,0,7('ꢀ72ꢀ'85$7,21ꢀ2)ꢀ7+(ꢀ
(;35(66('ꢀ:$55$17<ꢀ63(&,),('ꢀ$%29(ꢁ
4021-645C 12-29-10
6
Page 2 of 2
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
Listing and Code Approvals
1
A. Appliance Certification
C. BTU Specifications
Maximum
Input
BTU/h
Minimum
Input
BTU/h
Orifice
Size
(DMS)
MODEL: ESCAPE-42DV
Models
(U.S. or Canada)
LABORATORY: Underwriters Laboratories, Inc. (UL)
TYPE: Direct Vent Gas Appliance Heater
STANDARD: ANSI Z21.88-2002 • CSA2.33-M2002 • UL307B
US
(0-2000 FT)
52,000 35,000
46,800 31,500
50,000 33,000
45,000 29,700
26
27
45
46
Escape-42DV (NG)
Escape-42DV (LP)
CANADA
(2000-4500 FT)
US
(0-2000 FT)
This product is listed to ANSI standards for “Vented Gas
Appliance Heaters” and applicable sections of “Gas Burn-
ing Heating Appliances for Manufactured Homes and
Recreational Vehicles”, and “Gas Fired Appliances for
Use at High Altitudes”.
CANADA
(2000-4500 FT)
D. High Altitude Installations
NOTICE: This installation must conform with local codes.
In the absence of local codes you must comply with the
National Fuel Gas Code, ANSI Z223.1-latest edition in
the U.S.A. and the CAN/CGA B149 Installation Codes in
Canada.
NOTICE: If the heating value of the gas has been reduced,
these rules do not apply. Check with your local gas utility
or authorities having jurisdiction.
When installing above 2000 feet elevation:
• In the USA: Reduce input rate 4% for each 1000 feet
above 2000 feet.
NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.
This appliance is tested and approved as either supplemen-
tal room heat or as a decorative appliance. It should not be
factored as primary heat in residential heating calculations.
• In CANADA: Reduce input rate 10% for elevations
between 2000 feet and 4500 feet. Above 4500 feet,
consult local gas utility.
Check with your local gas utility to determine proper
orifice size.
B. Glass Specifications
This appliance is equipped with 5 mm ceramic glass. Re-
place glass only with 5 mm ceramic glass. Please contact
your dealer for replacement glass.
E. Non-Combustible Materials Specification
Material which will not ignite and burn. Such materials are
those consisting entirely of steel, iron, brick, tile, concrete,
slate, glass or plasters, or any combination thereof.
Materials that are reported as passing ASTM E 136,
Standard Test Method for Behavior of Materials in a
Vertical Tube Furnace at 750 ºC and UL763 shall be
considered non-combustible materials.
F. Combustible Materials Specification
Materials made of or surfaced with wood, compressed pa-
per, plant fibers, plastics, or other material that can ignite
and burn, whether flame proofed or not, or plastered or
unplastered shall be considered combustible materials.
G. Electrical Codes
NOTICE: This appliance must be electrically wired and
grounded in accordance with local codes or, in the absence
of local codes, with National Electric Code ANSI/NFPA
70-latest edition or the Canadian Electric Code CSA
C22.1.
• A 110-120 VAC circuit for this product must be protected
with ground-fault circuit-interrupter protection, in compliance
with the applicable electrical codes, when it is installed in
locations such as in bathrooms or near sinks.
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Inspection
Note: The following requirements reference various
Massachusetts and national codes not contained in this
document.
The state or local gas inspector of the side wall horizon-
tally vented gas fueled equipment shall not approve the
installation unless, upon inspection, the inspector ob-
serves carbon monoxide detectors and signage installed
in accordance with the provisions of 248 CMR 5.08(2)(a)1
through 4.
H. Requirements for the Commonwealth of
Massachusetts
For all side wall horizontally vented gas fueled equipment
installed in every dwelling, building or structure used in
whole or in part for residential purposes, including those
owned or operated by the Commonwealth and where the
side wall exhaust vent termination is less than seven (7)
feet above finished grade in the area of the venting, in-
cluding but not limited to decks and porches, the following
requirements shall be satisfied:
Exemptions
The following equipment is exempt from 248 CMR
5.08(2)(a)1 through 4:
• The equipment listed in Chapter 10 entitled “Equipment
Not Required To Be Vented” in the most current edition
of NFPA 54 as adopted by the Board; and
• Product Approved side wall horizontally vented gas fu-
eled equipment installed in a room or structure separate
from the dwelling, building or structure used in whole or
in part for residential purposes.
Installation of Carbon Monoxide Detectors
At the time of installation of the side wall horizontal vented
gas fueled equipment, the installing plumber or gas fitter
shall observe that a hard wired carbon monoxide detector
with an alarm and battery back-up is installed on the floor
level where the gas equipment is to be installed. In addi-
tion, the installing plumber or gas fitter shall observe that
a battery operated or hard wired carbon monoxide detec-
tor with an alarm is installed on each additional level of
the dwelling, building or structure served by the side wall
horizontal vented gas fueled equipment. It shall be the
responsibility of the property owner to secure the services
of qualified licensed professionals for the installation of
hard wired carbon monoxide detectors.
MANUFACTURER REQUIREMENTS
Gas Equipment Venting System Provided
When the manufacturer of Product Approved side wall
horizontally vented gas equipment provides a venting
system design or venting system components with the
equipment, the instructions provided by the manufacturer
for installation of the equipment and the venting system
shall include:
• Detailed instructions for the installation of the venting
system design or the venting system components; and
In the event that the side wall horizontally vented gas fu-
eled equipment is installed in a crawl space or an attic,
the hard wired carbon monoxide detector with alarm and
battery back-up may be installed on the next adjacent
floor level.
• A complete parts list for the venting system design or
venting system.
Gas Equipment Venting System NOT Provided
In the event that the requirements of this subdivision can
not be met at the time of completion of installation, the
owner shall have a period of thirty (30) days to comply
with the above requirements; provided, however, that dur-
ing said thirty (30) day period, a battery operated carbon
monoxide detector with an alarm shall be installed.
When the manufacturer of a Product Approved side wall
horizontally vented gas fueled equipment does not pro-
vide the parts for venting the flue gases, but identifies
“special venting systems”, the following requirements
shall be satisfied by the manufacturer:
• The referenced “special venting system” instructions
shall be included with the appliance or equipment in-
stallation instructions; and
Approved Carbon Monoxide Detectors
Each carbon monoxide detector as required in accor-
dance with the above provisions shall comply with NFPA
720 and be ANSI/UL 2034 listed and IAS certified.
• The “special venting systems” shall be Product Ap-
proved by the Board, and the instructions for that sys-
tem shall include a parts list and detailed installation
instructions.
Signage
A metal or plastic identification plate shall be permanent-
ly mounted to the exterior of the building at a minimum
height of eight (8) feet above grade directly in line with the
exhaust vent terminal for the horizontally vented gas fu-
eled heating appliance or equipment. The sign shall read,
in print size no less than one-half (1/2) in. in size, “GAS
VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OB-
STRUCTIONS”.
A copy of all installation instructions for all Product Ap-
proved side wall horizontally vented gas fueled equip-
ment, all venting instructions, all parts lists for venting
instructions, and/or all venting design instructions shall
remain with the appliance or equipment at the completion
of the installation.
See Gas Connection section for additional Common-
wealth of Massachusetts requirements.
8
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
Operating Instructions
2
- Adjustable safety gate.
A. Gas Fireplace Safety
• Install a switch lock or a wall/remote control with child
protection lockout feature.
WARNING
HOT SURFACES!
• Keep remote controls out of reach of children.
Glass and other surfaces are hot during
operation AND cool down.
• Never leave children alone near a hot fireplace, whether
operating or cooling down.
Hot glass will cause burns.
• DO NOT touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• Teach children to NEVER touch the fireplace.
• Consider not using the fireplace when children will be
present.
• CAREFULLY SUPERVISE children in same room as
fireplace.
• Alert children and adults to hazards of high temperatures.
Contact your dealer for more information, or visit: www.
hpba.org/safety-information.
To prevent unintended operation when not using your fire-
place for an extended period of time (summer months,
vacations, trips, etc):
High temperatures may ignite clothing or other
flammable materials.
• Keep clothing, furniture, draperies and other flammable
materials away.
• Remove batteries from remote controls.
• Turn off wall controls.
This appliance has been supplied with an integral barrier
to prevent direct contact with the fixed glass panel. DO
NOT operate the appliance with the barrier removed.
• Unplug 3 volt adapter plug and remove batteries on IPI
models.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
B. Your Fireplace
If you expect that small children or vulnerable adults may
come into contact with this fireplace, the following precau-
tions are recommended:
WARNING! DO NOT operate fireplace before read-
ing and understanding operating instructions. Failure
to operate fireplace according to operating instructions
could cause fire or injury.
• Install a physical barrier such as:
- A decorative firescreen.
DECORATIVE DOORS
(NOT SHOWN)
SECTION 2.E.
FIXED GLASS ASSEMBLY
(NOT SHOWN)
SECTION 14.G.
GRATE
SECTION 2.B.
MANTEL
HEARTH
CLEAR SPACE
SECTION 2.D.
Figure 2.1 General Operating Parts
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
9
C. Clear Space
E. Fixed Glass Assembly
WARNING! DO NOT place combustible objects in front
of the fireplace or block louvers. High temperatures may
start a fire. See Figure 2.2.
See Section 14.G.
F. Wall Controls and Wall Switches
Avoid placing candles and other heat-sensitive objects on
mantel or hearth. Heat may damage these objects.
Follow the instructions supplied with the control installed
to operate your fireplace:
For safety:
• Install a switch lock or a wall/remote control with child
protection lockout feature.
See your dealer if you have questions.
G. Before Lighting Fireplace
Before operating this fireplace for the first time, have a
qualified service technician:
• Verify all shipping materials have been removed from
inside and/or underneath the firebox.
• Review proper placement of logs, ember material and/or
other decorative materials.
• Check the wiring.
• Check the air shutter adjustment.
• Ensure that there are no gas leaks.
Figure 2.2 Clear Space
• Ensure that the glass is sealed and in the proper position
and that the integral barrier is in place.
D. Decorative Doors and Fronts
• Ensure that the flow of combustion air is not obstructed
(termination cap).
WARNING! Risk of Fire! Install ONLY doors or fronts
approved by Hearth & Home Technologies. Unapproved
doors or fronts may cause fireplace to overheat.
WARNING! Risk of Fire or Asphyxiation! DO NOT op-
erate fireplace with fixed glass assembly removed.
This fireplace has been supplied with an integral
barrier to prevent direct contact with the fixed glass
panel. DO NOT operate the fireplace with the barrier
removed.
Contact your dealer or Hearth & Home Technologies if
the barrier is not present or help is needed to properly
install one.
For more information refer to the instructions supplied with
your decorative door or front.
10
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
H. Lighting Instructions (IPI)
The IPI system may be operated with two D-cell batteries. When using batteries, unplug the transformer. To prolong battery
life, remove them when using the transformer.
FOR YOUR SAFETY
LIGHTING
READ BEFORE LIGHTING
INSTRUCTIONS (IPI)
WARNING: If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
1. This appliance is equipped with an ignition
device which automatically lights the burner.
DO NOT try to light the burner by hand.
• Immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions.
A. This appliance is equipped with an
intermittent pilot ignition (IPI) device
which automatically lights the burn-
er. DO NOT try to light the burner by
hand.
GAS
VALVE
• If you cannot reach your gas sup-
plier, call the fire department.
B. BEFORE LIGHTING, smell all around
the appliance area for gas. Be sure to
smell next to the floor because some
gas is heavier than air and will settle
on the floor.
C. DO NOT use this appliance if any
part has been under water. Imme-
diately call a qualified service tech-
nician to inspect the appliance and
to replace any part of the control
system and any gas control which
has been under water.
2. Wait five (5) minutes to clear out any gas.
Then smell for gas, including near the floor. If
you smell gas, STOP! Follow “B” in the Safety
Information located on the left side of this la-
bel. If you do not smell gas, go to next step.
WHAT TO DO IF YOU SMELL GAS
• DO NOT try to light any appliance.
3. To light the burner:
• DO NOT touch any electric switch; do
not use any phone in your building.
Equipped with wall switch: Turn ON/OFF switch
to ON.
Equipped with remote or wall control: Press
ON or FLAME button.
WARNING: CAUTION:
Equipped with thermostat: Set temperature to
desired setting.
Hot while in operation. DO NOT touch.
Keep children, clothing, furniture, gaso-
line and other liquids having flammable
vapors away.
DO NOT CONNECT LINE VOLT-
AGE (110/120 VAC OR 220/240
VAC) TO THE CONTROL VALVE.
4. If the appliance does not light after three tries,
call your service technician or gas supplier.
Improper installation, adjustment, al-
teration, service or maintenance can
cause injury or property damage. Re-
fer to the owner’s information manual
provided with this appliance.
TO TURN OFF
GAS TO APPLIANCE
1. Equipped with wall switch: Turn ON/OFF switch
DO NOT operate the appliance with
fixed glass assembly removed, cracked
or broken. Replacement of the fixed
glass assembly should be done by a
licensed or qualified service person.
to OFF.
This appliance needs fresh air for
safe operation and must be installed
so there are provisions for adequate
combustion and ventilation air.
Equipped with remote or wall control: Press
OFF button.
NOT FOR USE
WITH SOLID FUEL
Equipped with thermostat: Set temperature to
lowest setting.
If not installed, operated, and main- For use with natural gas and propane.
tained in accordance with the manufac- A conversion kit, as supplied by the
turer’s instructions, this product could manufacturer, shall be used to convert
expose you to substances in fuel or this appliance to the alternate fuel.
2. Service technician should turn off electric
power to the control when performing service.
fuel combustion which are known to the
State of California to cause cancer, birth
Also Certified for Installation in a
Bedroom or a Bedsitting Room.
593-913G
defects, or other reproductive harm.
For assistance or additional informa-
Keep burner and control compartment
tion, consult a qualified installer, ser-
clean. See installation and operating
vice agency or the gas supplier.
instructions accompanying appliance.
For additional information on operating your
Final inspection by
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
11
I. After Fireplace is Lit
Initial Break-in Procedure
• The fireplace should be run three to four hours
continuously on high.
• Turn the fireplace off and allow it to completely cool.
• Remove fixed glass assembly. See Section 14.G.
• Clean fixed glass assembly. See Section 3.
• Replace the fixed glass assembly and run continuously
on high an additional 12 hours.
This cures the materials used to manufacture the fire-
place.
NOTICE! Open windows for air circulation during fire-
place break-in.
• Some people may be sensitive to smoke and odors.
• Smoke detectors may activate.
J. Frequently Asked Questions
ISSUE
SOLUTIONS
This is a result of gas combustion and temperature variations. As the appliance warms, this
condensation will disappear.
Condensation on the glass
Blue flames
This is a result of normal operation and the flames will begin to yellow as the appliance is al-
lowed to burn for 20 to 40 minutes.
When first operated, this appliance may release an odor for the first several hours. This is caused
by the curing of the paint and the burning off of any oils remaining from manufacturing. Odor may
also be released from finishing materials and adhesives used around the appliance.
Odor from appliance
Film on the glass
This is a normal result of the curing process of the paint and logs. Glass should be cleaned
within 3 to 4 hours of initial burning to remove deposits left by oils from the manufacturing
process. A non-abrasive cleaner such as gas fireplace glass cleaner may be necessary. See
your dealer.
Noise is caused by metal expanding and contracting as it heats up and cools down, similar to
the sound produced by a furnace or heating duct. This noise does not affect the operation or
longevity of the appliance.
Metallic noise
In an intermittent pilot ignition system (IPI), the pilot flame should turn off when appliance is
turned off. Some optional control systems available with IPI models may allow pilot flame to
remain lit.
Is it normal to see the pilot flame burn
continually?
12
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Service
3
Doors, Surrounds, Fronts
Any safety screen or guard removed for servicing must be
replaced prior to operating the fireplace.
Frequency: Annually
By: Homeowner
When properly maintained, your fireplace will give you
many years of trouble-free service. We recommend an-
nual service by a qualified service technician.
Tools needed: Protective gloves, stable work surface
• Assess condition of screen and replace as necessary.
A. Maintenance Tasks-Homeowner
• Inspect for scratches, dents or other damage and repair
as necessary.
Installation and repair should be done by a qualified service
technician only. The fireplace should be inspected before
use and at least annually by a professional service person.
• Check that louvers are not blocked.
• Vacuum and dust surfaces.
The following tasks may be performed annually by the
homeowner. If you are uncomfortable performing any of
the listed tasks, please call your dealer for a service ap-
pointment.
Remote Control
Frequency: Seasonally
By: Homeowner
More frequent cleaning may be required due to lint from
carpeting or other factors. Control compartment, burner
and circulating air passageway of the fireplace must be
kept clean.
Tools needed: Replacement batteries and remote con-
trol instructions.
• Locate remote control transmitter and receiver.
• Verify operation of remote. Refer to remote control
operation instructions for proper calibration and setup
procedure.
CAUTION! Risk of Burns! The fireplace should be turned
off and cooled before servicing.
Glass Cleaning
Frequency: Seasonally
By: Homeowner
• Place batteries as needed in remote transmitters and
battery-powered receivers.
• Place remote control out of reach of children.
If not using your fireplace for an extended period of time
(summer months, vacations/trips, etc), to prevent unin-
tended operation:
Tools Needed: Protective gloves, glass cleaner, drop
cloth and a stable work surface.
CAUTION! Handle fixed glass assembly with care.
Glass is breakable.
• Avoid striking, scratching or slamming glass
• Avoid abrasive cleaners
• Remove batteries from remote controls.
• Unplug 3 volt adapter plug on IPI models.
• DO NOT clean glass while it is hot
Light Bulbs
• Prepare a work area large enough to accommodate fixed
glass assembly and door frame by placing a drop cloth
on a flat, stable surface.
Frequency: As needed
By: Homeowner
Tools needed: Protective gloves, replacement light bulbs.
Note: Fixed glass assembly and gasketing may have res-
idue that can stain carpeting or floor surfaces.
• Locate light bulb sockets in firebox. Remove existing
light bulbs and proceed with instructions in Section 14.F
of this manual.
• Remove door or decorative front from fireplace and set
aside on work surface.
• See Section 14.G for instructions to remove fixed glass
assembly.
• Clean glass with a non-abrasive commercially available
cleaner.
- Light deposits: Use a soft cloth with soap and water
- Heavy deposits: Use commercial fireplace glass
cleaner (consult with your dealer)
• Carefully set fixed glass assembly in place on fireplace.
Hold glass in place with one hand and secure glass
latches with the other hand.
• Reinstall door or decorative front.
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Venting
Firebox
Frequency: Seasonally
By: Homeowner
Frequency: Annually
By: Service Technician
Tools needed: Protective gloves and safety glasses.
Tools needed: Protective gloves, sandpaper, steel wool,
cloths, mineral spirits, primer and touch-up paint.
• Inspect venting and termination cap for blockage or
obstruction such plants, bird nests, leaves, snow, debris,
etc.
• Inspect for paint condition, warped surfaces, corrosion
or perforation. Sand and repaint as necessary.
• Verify termination cap clearance to subsequent construc-
tion (building additions, decks, fences, or sheds). See
Section 6.
• Replace appliance if firebox has been perforated.
Surface cracking or crazing of firebrick material is normal
and expected. The following types of cracks are acceptable
and do not require replacement of the unit or the firebox:
• Inspect for corrosion or separation.
• Verify weather stripping, sealing and flashing remains
intact.
• Cracks that do not propagate entirely through the
material.
• Inspect draft shield to verify it is not damaged or missing.
• Light fracture lines or “spider-webbing” on the surface of
the material.
B. Maintenance Tasks-Qualified Service
Technician
• Cracks that are less than 1/32 in. wide and less than 3
in. long.
The following tasks must be performed by a qualified ser-
vice technician.
• If cosmetically unacceptable, such cracks may be
repaired with the SRV-PACK service kit.
Gasket Seal and Glass Assembly Inspection
Frequency: Annually
Cracks that are unacceptable:
• Cracks greater than 1/32 in. wide and 3 in. long are at
risk of growing.
By: Qualified Service Technician
• Cracks that penetrate entirely through the firebrick
material.
Tools needed: Protective gloves, drop cloth and a stable
work surface.
Inspection for cracking should be run when the appliance
is cool. Cracks tend to close as the appliance heats up.
• Inspect gasket seal and its condition.
• Inspect fixed glass assembly for scratches and nicks that
can lead to breakage when exposed to heat.
Control Compartment and Firebox Top
Frequency: Annually
• Confirm there is no damage to glass or glass frame.
Replace as necessary.
By: Qualified Service Technician
• Verify that fixed glass assembly is properly retained and
attachment components are intact and not damaged.
Replace as necessary.
Tools needed: Protective gloves, vacuum cleaner, dust
cloths
• Vacuum and wipe out dust, cobwebs, debris or pet hair.
Use caution when cleaning these areas. Screw tips that
have penetrated the sheet metal are sharp and should
be avoided.
Logs
Frequency: Annually
By: Qualified Service Technician
Tools needed: Protective gloves.
• Remove all foreign objects.
• Verify unobstructed air circulation.
• Inspect for damaged or missing logs. Replace as neces-
sary. Refer to Section 14 for log placement instructions.
• Verify correct log placement and no flame impingement
causing sooting. Correct as necessary.
14
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
Burner Ignition and Operation
Frequency: Annually
By: Qualified Service Technician
Tools needed: Protective gloves, vacuum cleaner, whisk
broom, flashlight, voltmeter, indexed drill bit set, and a
manometer.
• Verify burner is properly secured and aligned with pilot
or igniter.
• Clean off burner top, inspect for plugged ports, corrosion
or deterioration. Replace burner if necessary.
• Replace Glowing embers with new dime-size pieces.
DO NOT block ports or obstruct lighting paths. Refer to
Section 14 for proper ember placement.
• Verify batteries have been removed from battery back-
up IPI systems to prevent premature battery failure or
leaking.
Figure 3.1 IPI Pilot Flame Patterns
• Check for smooth lighting and ignition carryover to all
ports. Verify that there is no ignition delay.
• Inspect for lifting or other flame problems.
• Verify air shutter setting is correct. See Section 14 for
required air shutter setting. Verify air shutter is clear of
dust and debris.
• Inspect orifice for soot, dirt and corrosion. Verify orifice
size is correct. See Service Parts List for proper orifice
sizing.
• Verify manifold and inlet pressures. Adjust regulator as
required.
• Inspect pilot flame pattern and strength. See Figure 3.1
for proper pilot flame pattern. Clean or replace orifice
spud as necessary.
• Inspect IPI flame sensing rod for soot, corrosion and
deterioration. Polish with fine steel wool or replace as
required.
• Verify that there is not a short in flame sensing circuit by
checking continuity between pilot hood and flame sense
rod. Replace pilot as necessary.
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Installer Guide
Getting Started
4
A. Typical Appliance System
NOTICE: Illustrations and photos reflect typical installations and are for design purposes only. Illustrations/diagrams are not
drawn to scale. Actual product may vary from pictures in manual
VERTICAL TERMINATION CAP
(SECTION 10.G)
NON-COMBUSTIBLE ROOF FLASHING
MAINTAINS MINIMUM CLEARANCE
AROUND PIPE (SECTION 10.E)
STORM COLLAR
(SECTION 10.F )
VENT PIPE PENETRATES ROOF
PREFERABLY WITHOUT AFFECTING
ROOF RAFTERS (SECTION 8.C)
ATTIC INSULATION SHIELD (NOT
VENT PIPE (SECTIONS 7 and 8)
SHOWN) MUST BE USED HERE TO
KEEP INSULATION AWAY FROM
VENT PIPE IF ATTIC IS INSULATED
(SECTION 8.D)
CEILING FIRESTOP
ON FLOOR OF ATTIC
(SECTION 8.C )
FRAMING/HEADER
(SECTION 5.C .)
FRAMING HEADED OFF
IN CEILING JOISTS
(SECTION 8.C )
OPTIONAL
WALL SWITCH
MANTEL AND
MANTEL LEG
(SECTIONS 5.D
and 13.B)
SURROUND
HEARTH EXTENSION
GAS LINE
(SECTION 11)
Figure 4.1 Typical System
16
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Design and Installation Considerations
D. Inspect Appliance and Components
Heat & Glo direct vent gas appliances are designed to
operate with all combustion air siphoned from outside of
the building and all exhaust gases expelled to the outside.
No additional outside air source is required.
• Carefully remove the appliance and components from
the packaging.
• The vent system components and decorative doors and
fronts may be shipped in separate packages.
Installation MUST comply with local, regional, state and
national codes and regulations. Consult insurance carrier,
local building inspector, fire officials or authorities having
jurisdiction over restrictions, installation inspection and
permits.
• If packaged separately, the log set and appliance grate
must be installed.
• Report to your dealer any parts damaged in shipment,
particularly the condition of the glass.
• Read all of the instructions before starting the instal-
lation. Follow these instructions carefully during the
installation to ensure maximum safety and benefit.
Before installing, determine the following:
• Where the appliance is to be installed.
• The vent system configuration to be used.
• Gas supply piping requirements.
• Electrical wiring requirements.
WARNING! Risk of Fire or Explosion! Damaged parts
could impair safe operation. DO NOT install damaged, in-
complete or substitute components. Keep appliance dry.
• Framing and finishing details.
Hearth & Home Technologies disclaims any responsibility for,
and the warranty will be voided by, the following actions:
• Whether optional accessories—devices such as a wall
switch—are desired.
• Installation and use of any damaged appliance or vent
system component.
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage. For
assistance or additional information, consult a qualified
service technician, service agency or your dealer.
• Modification of the appliance or vent system.
• Installation other than as instructed by Hearth & Home
Technologies.
• Improper positioning of the gas logs or the glass door.
• Installation and/or use of any component part not approved
by Hearth & Home Technologies.
C. Tools and Supplies Needed
Before beginning the installation be sure that the following
tools and building supplies are available.
Any such action may cause a fire hazard.
Tape measure
Pliers
Framing material
WARNING! Risk of Fire, Explosion or Electric Shock!
DO NOT use this appliance if any part has been under
water. Call a qualified service technician to inspect the
appliance and to replace any part of the control system
and/or gas control which has been under water.
Flat blade screwdriver
Phillips screwdriver
Framing square
Hammer
Gloves
Voltmeter
Plumb line
Level
Electric drill and bits (1/4 in.)
Safety glasses
Reciprocating saw
Manometer
Non-corrosive leak check solution
1/2 - 3/4 in. length, #6 or #8 Self-drilling screws
Caulking material (300ºF minimum continuous exposure
rating)
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Framing and Clearances
5
NOTICE: Illustrations reflect typical installations and are
FOR DESIGN PURPOSES ONLY. Illustrations/diagrams
are not drawn to scale. Actual installation may vary due to
individual design preference.
A. Selecting Appliance Location
When selecting a location for the appliance it is important to
consider the required clearances to walls (see Figure 5.1).
WARNING! Risk of Fire or Burns! Provide adequate
clearance around air openings and for service access.
Due to high temperatures, the appliance should be locat-
ed out of traffic and away from furniture and draperies.
B
A
PERPENDICULAR SIDEWALL
CAN OVERLAP TO 4 INCHES
FROM OPENING ON BOTH SIDES
C
D
E
A
B
C
D
E
Inches
57-1/2
22
91-1/2 64-3/4 45-3/4
2325 1644 1162
Millimeters 1461
559
Figure 5.1 Appliance Locations
18
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
300ºF continuous exposure rating to seal gaps. Gas line
holes and other openings should be caulked with caulk
with a minimum of 300ºF continuous exposure rating or
stuffed with unfaced insulation. If the appliance is being
installed on a cement surface, a layer of plywood may be
placed underneath to prevent conducting cold up into the
room.
B. Constructing the Appliance Chase
A chase is a vertical box-like structure built to enclose the
gas appliance and/or its vent system. In cooler climates
the vent should be enclosed inside the chase.
NOTICE: Treatment of ceiling firestops and wall shield
firestops and construction of the chase may vary with the
type of building. These instructions are not substitutes
for the requirements of local building codes. Therefore,
you MUST check local building codes to determine the
requirements to these steps.
C. Clearances
NOTICE: Install appliance on hard metal or wood surfaces
extending full width and depth. DO NOT install directly
on carpeting, vinyl, tile or any combustible material other
than wood.
Chases should be constructed in the manner of all out-
side walls of the home to prevent cold air drafting prob-
lems. The chase should not break the outside building
envelope in any manner.
WARNING! Risk of Fire! Maintain specified air space
clearances to appliance and vent pipe:
Walls, ceiling, base plate and cantilever floor of the chase
should be insulated. Vapor and air infiltration barriers
should be installed in the chase as per regional codes for
the rest of the home. Additionally, in regions where cold
air infiltration may be an issue, the inside surfaces may be
sheetrocked and taped for maximum air tightness.
• Insulation and other materials must be secured to prevent
accidental contact.
• The chase must be properly blocked to prevent blown
insulation or other combustibles from entering and
making contact with fireplace or chimney.
• Failure to maintain airspace may cause overheating and
a fire.
To further prevent drafts, the wall shield and ceiling fire-
stops should be caulked with caulk with a minimum of
A
FROM APPLIANCE
OPENING TO CEILING
E
B
C
J
F
H
D
I
G
* MINIMUM FRAMING DIMENSIONS
A
B
C
D
E
F
G
H
I
J
Rough
Opening
(Vent Pipe) (Height)
Rough
Rough
Rough
Clearance Combustible Combustible
Behind
Sides of
Front of
Opening Opening Opening
to Ceiling
Floor
Flooring
Appliance Appliance Appliance
(Depth)
(Width)
57-1/2
1461
Inches
mm
10
52-1/2
1334
22
43
0
0
12
1/2
13
1/2
13
36
254
559
1092
305
914
* Adjust framing dimensions for interior sheathing (such as sheetrock)
Figure 5.2 Clearances to Combustibles
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Combustible Mantel Legs or Wall Projections
D. Mantel and Wall Projections
WARNING! Risk of Fire! Comply with all minimum clear-
ances as specified. Framing or finishing material closer than
the minimums listed must be constructed entirely of noncom-
bustible materials (i.e., steel studs, concrete board, etc).
Combustible Mantels
4 INCH
MINIMUM
3-1/2 IN.
UNLIMITED
FINISH WALL
COMBUSTIBLE
NON-COMBUSTIBLE
MATERIAL
NO COMBUSTIBLES
IN THIS AREA
COMBUSTIBLE
FRAMING
39 IN.
METAL PANELS
(PROVIDED)
Figure 5.4 Combustible Mantel Leg or Wall Projections
(Acceptable on both sides of opening)
COMBUSTIBLE
PROJECTIONS
12 IN.
10-1/2 IN.
9 IN.
7-1/2 IN.
6 IN.
4-3/4 IN.
3 IN.
1/2 INCH
SHEETROCK
11-12 IN.
12 IN.
MIN.
8 IN. MIN.
6 IN. MIN.
NON-COMBUSTIBLE ZONE
11-1/2 IN.
NON-COMBUSTIBLE
FACING MATERIAL
MIN. 1/2 IN. THICKNESS
6 IN.
TOP OF FIREPLACE
OPENING
(NON-COMBUSTIBLE
BOARD)
Height
above
opening
in.
mm 152 178 203 228 254 279
in. 4-3/4 7-1/2 10-1/2 12
mm 76 121 152 191 228 267 305
6
7
8
9
10
11
12
305
Horizontal
Mantel
distance
3
6
9
Figure 5.3 Minimum Vertical and Maximum Horizontal
Dimensions of Combustibles
Figure 5.5 Non-Combustible Zone
20
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
E. Hearth Extension
MARBLE, GRANITE, TILE OR
OTHER NON-COMBUSTIBLE
HEARTH EXTENSION
WARNING! Risk of Fire! Hearth ex-
tension required to protect combustible
floors in front of appliance.
FRONT EDGE
OF ASH LIP
12 in.
The base of the fireplace may sit on a
combustible surface. The area in front of
the fireplace must be protected by a non-
combustible hearth extension, unless the
fireplace is raised a minimum of 3 inches
above the combustible floor or hearth.
See figures 5.6 and 5.7.
1 in. Max.
WOOD OR OTHER COMBUSTIBLE
FLOOR OR PLATFORM
BOTTOM OF FIREPLACE
Figure 5.6 Fireplace sitting on combustible surface
1 INCH
(BUILT INTO UNIT)
FRONT EDGE
OF ASH LIP
4 INCH
3 INCH MIN.
BOTTOM
OF FIREPLACE
WOOD OR OTHER
COMBUSTIBLE
FLOOR OR PLATFORM
UNDER THE OPENING
MAY BE
COMBUSTIBLE
MATERIAL
COMBUSTIBLES UP TO
1 INCH THICK ALLOWED
Figure 5.7 Fireplace raised a minimum of 3 inches away from combustible surface
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Termination Locations
6
A. Vent Termination Minimum Clearances
A
B
6 in. (minimum) up to 20 in.
152 mm/508 mm
18 in. minimum
457 mm
WARNING
20 in. and over
0 in. minimum
Fire Risk.
Gas, Wood or Fuel Oil
Termination Cap
Maintain vent clearance to combustibles as
specified.
• DO NOT pack air space with insulation or other
materials.
B
Failure to keep insulation or other materials away
from vent pipe may cause overheating and fire.
A *
HORIZONTAL
OVERHANG
Gas
Termination
Cap **
2 FT.
20 INCHES MIN.
VERTICAL
MIN.
WALL
LOWEST
DISCHARGE
OPENING
GAS DIRECT VENT
TERMINATION CAP
X
*
If using decorative cap cover(s), this distance may need to be
increased. Refer to the installation instructions supplied with the
decorative cap cover.
12
ROOF PITCH
IS X/ 12
In a staggered installation with both gas and wood or fuel oil
terminations, the wood or fuel oil termination cap must be
higher than the gas termination cap.
**
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
Figure 6.2 Staggered Termination Caps
Roof Pitch
H (Min.) Ft.
Flat to 6/12...........................................................1.0*
Over 6/12 to 7/12.................................................1.25*
Over 7/12 to 8/12.................................................1.5*
Over 8/12 to 9/12.................................................2.0*
Over 9/12 to 10/12...............................................2.5
Over 10/12 to 11/12.............................................3.25
Over 11/12 to 12/12.............................................4.0
Over 12/12 to 14/12.............................................5.0
Over 14/12 to 16/12.............................................6.0
Over 16/12 to 18/12.............................................7.0
Over 18/12 to 20/12.............................................7.5
Over 20/12 to 21/12.............................................8.0
* 3 foot minimum in snow regions
Figure 6.1 Minimum Height From Roof To Lowest Discharge
Opening
22
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
O
N
P
R
F
C
V
Q
B
J
H or i
B
V
B
V
V
E
X
D
V
V
G
H
M
V
V
V
V
L
H
V
A
A
K
K
Electrical
Service
V
V
V
= VENT TERMINAL
C
X
= AIR SUPPLY INLET
V
= AREA WHERE TERMINAL IS NOT PERMITTED
A
B
= 12 inches.................clearances above grade, veranda,
porch, deck or balcony
Covered Alcove Applications
(Spaces open only on one side and with an overhang)
= 12 inches.................clearance to window or door that may
be opened, or to permanently closed
window
N
= 6 inches ........... non-vinyl sidewalls
12 inches ......... vinyl sidewalls
= 18 inches ......... non-vinyl soffit and overhang
42 inches ......... vinyl soffit and overhang
= 8 ft.
O
P
C
= 24 inches.................clearance below unventilated soffit
24 inches.................clearance below ventilated soffit
42 inches.................clearance below vinyl soffits and
electrical service
QMIN
3 feet
6 feet
9 feet
12 feet
RMAX
D
E
F
= 6 inches...................clearance to outside corner
= 6 inches...................clearance to inside corner
1 cap
2 caps
3 caps
4 caps
2 x Q ACTUAL
1 x Q ACTUAL
2/3 x Q ACTUAL
1/2 x Q ACTUAL
= 3 ft. (Canada)..........not to be installed above a gas me-
ter/regulator assembly within 3 feet
horizontally from the center-line of the
regulator
QMIN = # termination caps x 3 RMAX = (2 / # termination caps) x QACTUAL
G
= 3 ft...........................clearance to gas service regulator
vent outlet
Measure vertical clearances from this surface.
H
= 12 inches.................clearancetonon-mechanical(unpow-
ered) air supply inlet, combustion air
inlet or direct-vent termination
i
= 3 ft. (U.S.A.)
6 ft. (Canada)...........clearance to a mechanical (powered)
air supply inlet
All mechanical air intakes within 10 feet of a termination cap
must be a minimum of 3 feet below termination.
J
= 7 ft.......................... Onpublic property: clearance above
paved sidewalk or a paved driveway.
A vent shall not terminate directly above a sidewalk or paved
driveway which is located between two single family dwellings
and serves both dwellings.
Measure horizontal clearances from this surface.
CAUTION! Risk of Burns! Termination caps are HOT,
consider proximity to doors, traffic areas or where people
may pass or gather (sidewalk, deck, patio, etc.). Listed cap
shields available. Contact your dealer.
K
L
=
6 inches.................clearance from sides of electrical
service
•
•
•
•
Local codes or regulations may require different
clearances.
= 12 inches................clearance above electrical service
Location of the vent termination must not interfere with access to the
electrical service.
Vent system termination is NOT permitted in screened
porches.
Vent system termination is permitted in porch areas with
two or more sides open.
M
= 18 inches ....................clearanceunderveranda, porch, deck,
balcony or overhang
42 inches ................vinyl or composite overhang
Permitted when veranda, porch, deck or balcony is fully open
on a minimum of 2 sides beneath the floor.
Hearth & Home Technologies assumes no responsibility
for the improper performance of the appliance when the
venting system does not meet these requirements.
Vinyl protection kits are suggested for use with vinyl siding.
•
Figure 6.3 Minimum Clearances for Termination
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
23
Vent Information and Diagrams
7
A. Approved Pipe
This appliance is approved for use with Hearth & Home
Technologies DVP venting systems. Refer to Section
16.B for vent component information.
DO NOT mix pipe, fittings or joining methods from differ-
ent manufacturers.
Vertical
The pipe is tested to be run inside an enclosed wall.
There is no requirement for inspection openings at each
joint within the wall.
8-1/2 in.
WARNING! Risk of Fire or Asphyxiation. This appli-
ance requires a separate vent. DO NOT vent to a pipe
serving a separate solid fuel burning appliance.
B. Vent Table Key
Horizontal
The abbreviations listed in this vent table key are used in
the vent diagrams.
Figure 7.1
Symbol
Description
D. Measuring Standards
First section (closest to appliance) of vertical length
V1
Vertical and horizontal measurements listed in the vent
diagrams were made using the following standards.
Second section of vertical length
V2
H1
H2
First section (closest to appliance) of horizontal length
Subsequent sections of horizontal length
• Pipe measurements are shown using the effective length
of pipe (see Figure 7.2).
• Horizontal terminations are measured to the outside
mounting surface (flange of termination cap) (see Figure
6.3).
C. Use of Elbows
• Vertical terminations are measured to bottom of
termination cap.
Diagonal runs have both vertical and horizontal vent as-
pects when calculating the effects. Use the rise for the
vertical aspect and the run for the horizontal aspect (see
Figure 7.1).
• Horizontal pipe installed level with no rise.
Two 45º elbows may be used in place of one 90º elbow.
On 45º runs, one foot of diagonal is equal to 8-1/2 in. (216
mm) horizontal run and 8-1/2 in. (216 mm) vertical run. A
length of straight pipe is allowed between two 45º elbows
(see Figure 7.1).
Effective Length
Pipe
Inches
4
Millimeters
102
DVP4
DVP6
6
12
152
305
DVP12
DVP24
DVP36
DVP48
DVP6A
Effective
Height/Length
24
610
36
914
48
1219
76 to 152
3 to 6
DVP12A 3 to 12 76 to 305
DVP12MI 3 to 12 76 to 305
DVP24MI 3 to 24 76 to 610
Figure 7.2 DVP Pipe Effective Length
24
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
E. Vent Diagrams
Top Vent - Horizontal Termination
One Elbow
V1 Minimum
H1 Maximum
2 ft..
610 mm
914 mm
1.2 m
7 in*
2 ft.
178 mm
Note: Must have a 24 inches mini-
Note: A flue restrictor can only
be used in vent runs that in-
clude no elbows and exceed
30 ft. total of straight vertical.
3 ft.
4 ft.
610 mm
1.2 m
2.7 m
3.7 m
4.3 m
6.1 m
12.2 m
mum vertical vent before attaching
any elbow to the unit.
4 ft.
5 ft.
1.5 m
9 ft.
6 ft.
1.8 m
12 ft.
14 ft.
20 ft.
40 ft.
7 ft.
2.1 m
10 ft.
20 ft.
3.0 m
6.1 m
After V1 = 6 ft. then H1 = 2 x V ft. Maximum
V1 + H1 = 60 ft. Maximum
V1
*when used with approved termination caps
H1
Figure 7.3
V1 Minimum
H1+ H2
Two Elbows
3 ft.
914 mm
1.2 m
1.5 m
1.8 m
2.1 m
3.0 m
6.1 m
18 in
457 mm
914 mm
2.1 m
4 ft.
5 ft.
3 ft.
7 ft.
Note: Must have a 24 inches mini-
mum vertical vent before attaching
any elbow to the unit.
Note: A flue restrictor can only
be used in vent runs that in-
clude no elbows and exceed
30 ft. total of straight vertical.
6 ft.
10 ft.
12 ft.
18 ft.
20 ft.
3.0 m
7 ft.
3.7 m
10 ft.
20 ft.
5.5 m
6.1 m
After V1= 6 ft. then H1 = 2 x V1 ft. Maximum
V1 + H1 + H2 = 60 ft. Maximum
H1 + H2 = 20 ft. Maximum
V1
H2
H1
Figure 7.4
INSTALLED
HORIZONTALLY
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Top Vent - Horizontal Termination - (continued)
Three Elbows
V1
H1
178 mm
V2
*
H2
2 ft. 610 mm
3 ft. 914 mm
7 in
2 ft.
H2 Max = 2 X V2
H2 Max = 2 X V2
H2 Max = 2 X V2
H2 Max = 2 X V2
H2 Max = 2 X V2
H2 Max = 2 X V2
H2 Max = 2 X V2
610 mm
1.2 m
2.7 m
3.7 m
4.3 m
6.1 m
*
Note: Must have a 24 inches mini-
mum vertical vent before attaching
any elbow to the unit.
4 ft.
5 ft.
1.2 m
1.5 m
1.8 m
2.1 m
3.0 m
4 ft.
*
9 ft.
*
6 ft.
12 ft.
14 ft.
20 ft.
*
7 ft.
*
Note: A flue restrictor can only
be used in vent runs that in-
clude no elbows and exceed
30 ft. total of straight vertical.
10 ft.
*
V1 + H1 must be adhered to.
* V2 has no specific restrictions EXCEPT,
Ht max = 2 x Vt and Vtotal + Htotal cannot exceed 60 ft. Maximum
H2
V2
V1
H1
Figure 7.5
26
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
Top Vent - Vertical Termination
No Elbow
V1 = 50 ft. Max. (15.2 m)
V1 = 3 ft. Min. (914 mm)
Note: A flue restrictor can only
be used in vent runs that in-
clude no elbows and exceed
30 ft. total of straight vertical.
FLUE
RESTRICTOR
FLUE RESTRICTOR
V1
Figure 7.6
V1
H1
V2
*
Two Elbows
2 ft.
3 ft.
4 ft.
5 ft.
6 ft.
610 mm
914 mm
1.2 m
1 ft.
3 ft.
4 ft.
9 ft.
12 ft.
305 mm
914 mm
1.2 m
*
Note: Must have a 24 inches mini-
mum vertical vent before attaching
any elbow to the unit.
*
1.5 m
2.7 m
*
1.8 m
3.7 m
*
Note: A flue restrictor can only
be used in vent runs that in-
clude no elbows and exceed
30 ft. total of straight vertical.
V1 + V2 + H1 = 50 ft. (15.2 m) Max.
*No specific restrictions on this value EXCEPT
V1 + V2 + H1 cannot exceed 60 ft. (18.3 m).
After V1 = 6 ft., then H1 Max.= V1 x 2
V2
V1
H1
Figure 7.7
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
27
Top Vent - Vertical Termination - (continued)
Three Elbows
V1
610 mm
H1
*
H2
*
V2
**
**
**
**
**
**
**
Ht Max.
178 mm
2 ft.
3 ft.
4 ft.
5 ft.
6 ft.
7 ft.
10 ft.
7 in
2 ft.
914 mm
1.2 m
1.5 m
1.8 m
2.1 m
3.0 m
*
*
610 mm
1.2 m
2.4 m
3.7 m
4.3 m
6.1 m
Note: Must have a 24 inches mini-
mum vertical vent before attaching
any elbow to the unit.
*
*
4 ft.
*
*
8 ft.
*
*
12 ft.
14 ft.
20 ft.
Note: A flue restrictor can only
be used in vent runs that in-
clude no elbows and exceed
30 ft. total of straight vertical.
*
*
*
*
*H1 and H2 has no specific restrictions EXCEPT,
after V1 = 6 ft., then Ht Max = 2 x V1
**VT +HT = 60 ft. Max.
V2
H1
H2
V1
INSTALLED
HORIZONTALLY
Figure 7.8
28
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
Vent Clearances and Framing
8
A. Pipe Clearances to Combustibles
B. Wall Penetration Framing
WARNING! Risk of Fire! Maintain air space clearance to
vent. DO NOT pack insulation or other combustibles:
Combustible Wall Penetration
Whenever a combustible wall is penetrated, you must
frame a hole for the wall shield firestop(s). The wall shield
firestop maintains minimum clearances and prevents cold
air infiltration.
• Between ceiling firestops
• Between wall shield firestops
• Around vent system
• The opening must be framed on all four sides using the
same size framing materials as those used in the wall
construction.
Failure to keep insulation or other material away from
vent pipe may cause over heating and fire.
• A wall shield firestop is required on one side only on in-
terior walls. If your local inspector requires a wall shield
firestop on both sides, then both wall shield firestops
must have a heat shield (refer to Section 16.B.) at-
tached to them.
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm).
• DVP heat shield - designed to be used on a wall 4 in. to 7-1/4 in. (102 mm to
184 mm) thick.
• If wall thickness is less than 4 in. the existing heat shields must be field trimmed.
If wall thickness is greater than 7-1/4 in. a DVP-HSM-B will be required.
• See Section 10.M. for information for regarding the in-
stallation of a horizontal termination cap.
Heat
Shield
3 in. (76 mm)
top clearance
Heat
3 in. (76 mm)
top clearance
Non-Combustible Wall Penetration
Shield
If the hole being penetrated is surrounded by noncom-
bustible materials such as concrete, a hole with diameter
one inch greater than the pipe is acceptable.
1 in. (25 mm)
clearance around
vertical sections
1 in. (25 mm)
clearance
bottom & sides
Wall
Shield
Firestop
Whenever a non-combustible wall is penetrated, the wall
shield firestop is only required on one side and no heat
shield is necessary.
WALL
Figure 8.1 Horizontal Venting Clearances To Combustible
Materials
10 in.
12 in.
B
A
A*
B
73 -1/8 in. 72 -1/8 in.
* Shows center of vent framing hole for top venting. The center of the hole is
one (1) inch (25.4 mm) above the center of the horizontal vent pipe.
Figure 8.2 Exterior Wall Hole
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
29
C. Install the Ceiling Firestop
A ceiling firestop MUST be used between
floors and attics.
• DVP pipe only - Frame an opening 10 in.
by 10 in. (254 mm by 254 mm) whenever
the vent penetrates a ceiling/floor (see
Figure 8.3).
ATTIC ABOVE
• Frame the area with the same sized lumber
as used in ceiling/floor joist.
• The ceiling firestop may be installed above or
below the ceiling joists when installed with a
attic insulation shield. It must be under joists
between floors that are not insulated. Refer
to Figure 8.4.
A
• Secure with three fasteners on each side.
WARNING! Risk of Fire! DO NOT pack insu-
lation around the vent. Insulation must be kept
back from the pipe to prevent overheating.
A
A
PIPE
10 in. (254 mm)
DVP
Figure 8.3 Installing Ceiling Firestop
INSTALL ATTIC INSULATION SHIELDS
BEFORE OR AFTER INSTALLATION OF VENT SYSTEM
3 FASTENERS
PER SIDE
CEILING FIRESTOP
CEILING FIRESTOP
INSTALLED BELOW CEILING
INSTALLED ABOVE CEILING
Figure 8.4 Installing the Attic Shield
30
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
D. Install Attic Insulation Shield
BEND ALL TABS INWARD 90°
TO MAINTAIN CLEARANCE
AND PREVENT INSULATION
FROM FALLING INSIDE
WARNING! Fire Risk. DO NOT allow loose materials or
insulation to touch vent. Hearth & Home Technologies
Inc. requires the use of an attic shield.
The National Fuel Gas Code ANSI Z223.1 and NFPA 54
requires an attic shield constructed of 26 gauge minimum
metal that extends at least 2 in. (51 mm) above insulation.
BEND 3 TABS
OUTWARD TO
Attic shields must meet specified clearance and be se-
cured in place.
FASTEN TO CEILING
FIRESTOP-BEND
REMAINING TABS
INWARD 90 DEGREES
TO MAINTAIN
Flat Ceiling Installation
• Remove one shield from box.
CLEARANCE
INSERT 3
SCREWS
NOTICE: Cut previously installed batt insulation to make
room for the attic insulation shield.
• Wrap shield around pipe if pipe is already installed in
area to be insulated.
• Match the three holes in each side and fasten with three
screws to form a tube.
• Bend three tabs on the bottom of the shield outward to
allow attachment to the ceiling firestop.
Figure 8.5 Attic Insulation Shield
• Bend the remaining bottom tabs inward 90° to maintain
the air space between the pipe and the shield. Set the
shield on the ceiling firestop and attach to the firestop.
E. Installing the Optional Heat-Zone® Gas Kit
• Remove the knockouts from the top of the appliance and
discard them (see Figure 8.6).
• Bend all tabs inward 90° around the top of the shield.
These tabs must be used to prevent blown insulation
from getting between the shield and vent pipe, and to
maintain air space clearance.
• Center the duct collar around the exposed hole and
attach it to the appliance with 3 screws. Note: Do this
BEFORE final positioning of the appliance.
• Determine the location for the air register/fan housing
assembly.
• Reference the Heat-Zone® Gas Kit instructions for the
remaining installation steps.
Vaulted Ceiling Installation
• Remove one shield from box.
NOTICE: Cut previously installed batt insulation to make
room for the attic insulation shield.
• Cut the attic insulation shield (if application is for vaulted
ceiling) to fit your ceiling pitch. Snip cut edge to recreate
1 in. bend tabs all the way around the bottom.
• Wrap shield around pipe if pipe is already installed in
area to be insulated.
• Match the three holes in each side and fasten with three
screws to form a tube.
KNOCKOUTS
• Bend three tabs on the bottom of the shield outward to
allow attachment to the ceiling firestop.
• Bend the remaining bottom tabs inward 90º to maintain
the air space between the pipe and the shield. Set the
shield on the ceiling firestop and attach to the firestop.
• Bend all tabs inward 90º around the top of the shield.
These tabs must be used to prevent blown insulation
from getting between the shield and vent pipe, and to
maintain air space clearance.
Figure 8.6 Heat Zone® Knockouts
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
31
Appliance Preparation
9
A. Removing Non-combustible Facing Ma-
terial Assembly
The non-combustible assembly is located on the back side
of appliance.
CAUTION
Handle with care.
• Non-combustible material may be damaged if dropped.
• Hold non-combustible pieces in place.
• Remove and save two screws from upper bracket.
• Remove non-combustible pieces.
• Remove and save three screws from lower bracket.
• Discard brackets.
• Replace screws in holes where brackets were attached
to appliance.
Nailing tabs
(Both sides)
B. Securing and Leveling the Appliance
WARNING! Risk of Fire! Prevent contact with:
• Sagging or loose insulation
• Insulation backing or plastic
• Framing and other combustible materials
Figure 9.1 Proper Positioning and Securing of an Appliance
Block openings into the chase to prevent entry of blown-
in insulation. Make sure insulation and other materials
are secured.
DO NOT notch the framing around the appliance
standoffs.
Failure to maintain air space clearance may cause
overheating and fire.
The diagram shows how to properly position and secure
the appliance (see Figure 9.1). Nailing tabs are provided
to secure the appliance to the framing members.
• Bend out nailing tabs on each side.
• Place the appliance into position.
• Keep nailing tabs flush with the framing.
• Level the appliance from side to side and front to back.
• Shim the appliance as necessary. It is acceptable to use
wood shims underneath the appliance.
• Secure the appliance to the framing by using nails or
screws through the nailing tabs.
• Secure the appliance to the floor by inserting two screws
through the pilot holes at the bottom of the appliance.
32
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
C. Installing Non-combustible Facing Material
NON-COMBUSTIBLE
ZONE
WARNING
Fire Risk.
• Follow these instructions exactly.
• Facing materials must be installed properly to
prevent fire.
• No materials may be substituted without
authorization by Hearth & Home Technologies.
43 in.
• Center and attach two top boards to the framing
members. See Figure 9.2.
• Attach left and right side pieces to framing members.
• Use fasteners from fastener packet (in manual bag) in
shaded areas.
60 in.
Figure 9.3 Complete Installation of Non-combustible Facing
Material
• Use regular sheetrock screws in non-shaded areas.
• Use a wet or dry towel or soft brush to remove dust or
dirt from facing material.
• Apply a non-combustible adhesive to attach tile,
stone or other non-combustible finishing materials per
manufacturer’s instructions.
NON-COMBUSTIBLE
FACING MATERIAL
(9 IN. WIDE, SUPPLIED ATTACHED TO
BACK OF APPLIANCE)
9 IN.
NO FASTENERS
2 IN.
IN THIS AREA
1 IN.
APPLY FASTENERS
FROM FASTENER PACKET
IN THESE AREAS
Figure 9.2 Attaching Non-combustible Facing Material
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
33
Installing Vent Pipe
10
A. Assemble Vent Sections
Attach Vent to the Firebox Assembly
Note: The end of the pipe sections with the lanced tabs will face
toward the appliance.
Attach the first pipe section to the starting collar:
• Lanced pipe end to the starting collar
• Inner pipe over inner collar
• Push the pipe section until all lanced tabs snap in place
• Lightly tug on pipe to confirm it has locked.
Commercial, Multi-family (Multi-level exceeding two sto-
ries), or High-Rise Applications
All outer pipe joints must be sealed with high temperature
silicone (minimum of 300ºF continuous exposure rating), in-
cluding the slip section that connects directly to the hori-
zontal termination cap.
Figure 10.1 High Temperature Silicone Sealant
• Apply a bead of silicone sealant inside the female outer
pipe joint prior to joining sections. See Figure 10.1
A
Lances
• Only outer pipes need to be sealed. All unit collar, pipe,
slip section, elbow and cap outer flues shall be sealed
in this manner, unless otherwise stated.
WARNING! Risk of Fire or Explosion! DO NOT break
silicone seals on slip sections. Use care when remov-
ing termination cap from slip pipe. If slip section seals
are broken during removal of the termination cap, vent
may leak.
B
Figure 10.3
Figure 10.2
Assemble Pipe Sections
Note: Make sure that the seams are not aligned to prevent
unintentional disconnection.
Per Figure 10.2:
• Start the inner pipe on the lanced end of section A into
the flared end of section B.
• Start the outer pipe of section A over the outer pipe of
section B.
• Once both vents sections are started, push firmly until
all lanced tabs lock into place.
• Lightly tug on the pipe to confirm the tabs have locked.
It is acceptable to use screws no longer than 1/2 in. (13
mm) to hold outer pipe sections together. If predrilling holes,
DO NOT penetrate inner pipe.
CORRECT
For 90° and 45° elbows that are changing the vent direction
from horizontal to vertical, one screw minimum should be
put in the outer flue at the horizontal elbow joint to prevent
the elbow from rotating. Use screws no longer than 1/2
in. (13 mm). If predrilling screw holes, DO NOT penetrate
inner pipe.
INCORRECT
Figure 10.4 Seams
34
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Assemble Slip Sections
C. Secure the Vent Sections
• Slide the inner flue of the slip section into the inner flue of
the pipe section and the outer flue of the slip section over
the outer flue of the pipe section. See Figure 10.5.
• Vertical runs must be supported every 8 ft. (2.44 m) after
the 25 ft. (7.62 m) maximum unsupported rise.
• Horizontal sections must be supported every 5 feet
(1.52 m).
• Slide together to the desired length.
• Vent supports or plumbers strap (spaced 120º apart)
may be used to support vent sections. See Figures 10.7
and 10.8.
• Wall shield firestops may be used to provide horizontal
support to vent sections.
WARNING! Risk of Fire, Explosion or Asphyxiation!
Improper support may allow vent to sag and separate.
Use vent run supports and connect vent sections per in-
stallation instructions. DO NOT allow vent to sag below
connection point to appliance.
Pilot hole
Figure 10.5 Slip Section Pilot Holes
120º
• Maintain a 1-1/2 in. (38 mm) overlap between the slip
section and the pipe section.
• Secure the pipe and slip section with two screws no
longer than 1/2 in. (13 mm), using the pilot holes in the
slip section. See Figure 10.7.
Figure 10.7 Securing Vertical Pipe Sections
120º
Figure 10.6 Screws into Slip Section
• Continue adding pipe as necessary following instructions
in “Assembling Pipe Sections.”
NOTICE: If slip section is too long, the inner and outer flues
of the slip section can be cut to the desired length.
Figure 10.8 Securing Horizontal Pipe Sections
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
35
D. Disassemble Vent Sections
• Rotate either section (see Figure 10.9) so the seams
on both pipe sections are aligned as shown in Figure
10.10.
• Pull carefully to separate the pieces of pipe.
Figure 10.9 Rotate Seams for Disassembly
Figure 10.10 Align and Disassemble Vent Sections
36
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
E. Install Metal Roof Flashing
• See minimum vent heights for various pitched roofs
(Figure 10.11) to determine the length of pipe to extend
through the roof.
CAULK
• Slide the roof flashing over the pipe sections extending
through the roof as shown in Figure 10.12.
HORIZONTAL
OVERHANG
2 FT.
20 INCHES MIN.
VERTICAL
MIN.
WALL
LOWEST
DISCHARGE
OPENING
Figure 10.12
GAS DIRECT VENT
TERMINATION CAP
F. Assemble and Install Storm Collar
X
12
CAUTION! Risk of Cuts, Abrasions or Flying Debris.
Wear protective gloves and safety glasses during instal-
lation. Sheet metal edges are sharp.
ROOF PITCH
IS X/ 12
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
• Connect both halves of the storm collar with two screws
(see Figure 10.13).
• Wrap the storm collar around the exposed pipe section
closest to the roof and align brackets. Insert a bolt
(provided) through the brackets and tighten the nut to
complete the storm collar assembly. Make sure the collar
is tight against the pipe section.
Roof Pitch
H (Min.) Ft.
Flat to 6/12........................................1.0*
Over 6/12 to 7/12............................1.25*
Over 7/12 to 8/12..............................1.5*
Over 8/12 to 9/12..............................2.0*
Over 9/12 to 10/12............................. 2.5
Over 10/12 to 11/12......................... 3.25
Over 11/12 to 12/12........................... 4.0
Over 12/12 to 14/12........................... 5.0
Over 14/12 to 16/12........................... 6.0
Over 16/12 to 18/12........................... 7.0
Over 18/12 to 20/12........................... 7.5
Over 20/12 to 21/12........................... 8.0
• Slide the assembled storm collar down the pipe section
until it rests on the roof flashing (see Figure 10.14).
• Caulk around the top of the storm collar (see Figure 10.15).
* 3 foot minimum in snow regions
Figure 10.11 Minimum Height From Roof To Lowest Discharge
Opening
Figure 10.13 Assembling the Storm Collar
NOTICE: Failure to properly caulk the roof flashing and
pipe seams may permit entry of water.
• Caulk the gap between the roof flashing and the outside
diameter of the pipe.
• Caulk the perimeter of the flashing where it contacts the
roof surface. See Figure 10.12.
• Caulk the overlap seam of any exposed pipe sections
that are located above the roof line.
Figure 10.14 Assembling the Storm Collar Around the Pipe
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
37
G. Install Vertical Termination Cap
H. Heat Shield Requirements for Horizontal
Termination
• Attach the vertical termination cap by sliding the inner
collar of the cap into the inner flue of the pipe section
while placing the outer collar of the cap over the outer
flue of the pipe section.
WARNING! Risk of Fire! To prevent overheating and fire,
heat shields must extend through the entire wall thick-
ness.
• Secure the cap by driving three self-tapping screws
(supplied) through the pilot holes in the outer collar of the
cap into the outer flue of the pipe (see Figure 10.15).
• DO NOT remove the heat shields attached to the
wall shield firestop and the horizontal termination cap
(shown in Figure 10.16).
• Heat shields must overlap 1-1/2 in. (38 mm) mini-
mum.
TERMINATION CAP
There are two sections of the heat shield. One section
is factory-attached to the wall shield firestop. The other
section is factory-attached to the cap. See Figure 10.16.
If the wall thickness does not allow the required 1-1/2 in.
(38 mm) heat shield overlap when installed, an extended
heat shield must be used.
• If the wall thickness is less than 4 in. (102 mm), the
heat shields on the cap and wall shield firestop must be
trimmed. A minimum 1-1/2 in. (38 mm) overlap MUST
be maintained.
(1 of 3)
• Useanextendedheatshieldifthefinishedwallthickness
is greater than 7-1/4 in. (184 mm).
STORM
COLLAR
• The extended heat shield may need to be cut to length
maintaining sufficient length for a 1-1/2 in. (38 mm)
overlap between heat shields.
SCREWS
CAULK
• Attach the extended heat shield to either of the existing
heatshieldsusingthescrewssuppliedwiththeextended
heat shield. Refer to vent components diagrams in the
back of this manual.
Figure 10.15
• Rest the small leg on the extended heat shield on top
of the pipe section to properly space it from the pipe
section.
Important Notice: Heat shields may not be field constructed.
38
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: When using termination caps with factory-supplied
heat shield attached, no additional wall shield firestop is
required on the exterior side of a combustible wall.
I. Install Horizontal Termination Cap
WARNING! Risk of Fire! The telescoping flue section of
the termination cap MUST be used when connecting vent.
• 1-1/2 (38 mm) minimum overlap of flue telescoping
section is required.
HEAT SHIELD OR
HEAT SHIELD
EXTENDED
Failure to maintain overlap may cause overheating and
fire.
1-1/2 IN. (38 MM) MIN.
HEAT SHIELD
OVERLAP
WALL SHIELD
FIRESTOP
• Vent termination must not be recessed in the wall. Siding
may be brought to the edge of the cap base.
• Flash and seal as appropriate for siding material at
outside edges of cap.
SLIP SECTION
CAN BE EXTENDED
• When installing a horizontal termination cap, follow
the cap location guidelines as prescribed by current
ANSI Z223.1 and CAN/CGA-B149 installation codes
and refer to Section 6 of this manual.
INNER VENT
SHEATHING
OUTER VENT
INTERIOR
EXTERIOR
CAUTION! Risk of Burns! Local codes may require in-
stallation of a cap shield to prevent anything or anyone
from touching the hot cap.
VENT DEPTH FROM BACK OF APPLIANCE TO
OUTSIDE SURFACE OF EXTERIOR WALL
(SEE CHART BELOW)
Figure 10.16 Venting through the wall
Termination Cap Specification Chart
(depth without using additional pipe sections)
DVP-TRAPK1 DVP-TRAP1 DVP-TRAPK2 DVP-TRAP2
Top Vent
Depth
Rear Vent
Depth
Top Vent
Depth
Rear Vent
Depth
3-1/2 in. to
5-3/8 in.
6 in. to
10 in.
N/A
N/A
Escape-
42DV
DVP-HPC1 DVP-HPC1
DVP-HPC2 DVP-HPC2
Top Vent
Depth
Rear Vent
Depth
Top Vent
Depth
Rear Vent
Depth
3-1/2 in. to
5-5/8 in.
5-3/4 in. to
9-3/4 in.
N/A
N/A
DVP-TRAP1 can adjust 1-1/2 in. (3-1/8 to 4-5/8)
DVP-TRAP2 can adjust 4 in. (5-3/8 to 9-3/8)
DVP-HPC1 can adjust 2-1/8 in. (4-1/4 to 6-3/8)
DVP-HPC2 can adjust 4-1/8 in. (6-3/8 to 10-1/2)
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
39
Gas Information
11
A. Fuel Conversion
C. Gas Connection
• Make sure the appliance is compatible with available gas
types.
• Refer to Reference Section 16 for location of gas line
access in appliance.
• Conversions must be made by a qualified service
technician using Hearth & Home Technologies specified
and approved parts.
• Gas line may be run through knockout(s) provided.
• The gap between supply piping and gas access hole
may be caulked with caulk with a minimum of 300ºF
continuous exposure rating or stuffed with non-
combustible, unfaced insulation to prevent cold air
infiltration.
B. Gas Pressure
• Optimum appliance performance requires proper input
pressures.
• Ensure that gas line does not come in contact with outer
wrap of the appliance. Follow local codes.
• Gas line sizing requirements will be determined in ANSI
Z223.1 National Fuel Gas Code in the USA and CAN/
CGA B149 in Canada.
• Pipe incoming gas line into valve compartment.
• Connect incoming gas line to the 1/2 in. (13 mm)
connection on manual shutoff valve.
• Pressure requirements are:
WARNING! Risk of Fire or Explosion! Support control
when attaching pipe to prevent bending gas line.
Gas Pressure
Minimum inlet pressure
Maximum inlet pressure
Manifold pressure
Natural Gas
5.0 in. w.c.
14.0 in. w.c.
3.5 in. w.c.
Propane
11.0 in. w.c.
14.0 in. w.c.
9.2 in. w.c.
• A small amount of air will be in the gas supply lines.
WARNING! Risk of Fire or Explosion! Gas build-up dur-
ing line purge could ignite.
WARNING! Risk of Fire or Explosion! High pressure
will damage valve. Low pressure may cause explosion.
• Purge should be performed by qualified service
technician.
• Ensure adequate ventilation.
• Ensure there are no ignition sources such as sparks
or open flames.
• Verify inlet pressures. Verify minimum pressures when
other household gas appliances are operating.
• Install regulator upstream of valve if line pressure is
greater than 1/2 psig.
Light the appliance. It will take a short time for air to purge
from lines. When purging is complete the appliance will
light and operate normally.
WARNING
WARNING! Risk of Fire, Explosion or Asphyxiation!
Check all fittings and connections with a non-corrosive
commercially available leak-check solution. DO NOT use
open flame. Fittings and connections could have loos-
ened during shipping and handling.
Fire Risk.
Explosion Hazard.
High pressure will damage valve.
• Disconnect gas supply piping BEFORE
pressure testing gas line at test pressures
above 1/2 psig.
WARNING! Risk of Fire! DO NOT change valve settings.
This valve has been preset at the factory.
• Close the manual shutoff valve BEFORE
pressure testing gas line at test pressures
equal to or less than 1/2 psig.
D. High Altitude Installations
NOTICE: If the heating value of the gas has been reduced,
these rules do not apply. Check with your local gas utility
or authorities having jurisdiction.
Note: Have the gas supply line installed in accordance with
local codes, if any. If not, follow ANSI 223.1. Installation
should be done by a qualified installer approved and/or
licensed as required by the locality. (In the Commonwealth
of Massachusetts installation must be performed by a
licensed plumber or gas fitter).
When installing above 2000 feet elevation:
• In the USA: Reduce burner orifice 4% for each 1000 feet
above 2000 feet.
• In CANADA: Reduce burner orifice 10% for elevations
between 2000 feet and 4500 feet. Above 4500 feet,
consult local gas utility.
Note: A listed (and Commonwealth of Massachusetts ap-
proved) 1/2 in. (13 mm) T-handle manual shut-off valve
and flexible gas connector are connected to the 1/2 in. (13
mm) control valve inlet.
• If substituting for these components, please consult
local codes for compliance.
40
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Information
12
C. Optional Accessories Requirements
A. Wiring Requirements
• This appliance may be used with a wall switch or a wall
mounted thermostat.
NOTICE: This appliance must be electrically wired
and grounded in accordance with local codes or, in the
absence of local codes, with National Electric Code
ANSI/NFPA 70-latest edition or the Canadian Electric
Code CSA C22.1.
Wiring for optional Hearth & Home Technologies approved
accessories should be done now to avoid reconstruction.
Follow instructions that come with those accessories.
• Wire the appliance junction box to 110-120 VAC. This is
required for proper operation of the appliance.
This appliance comes standard with a multi-function
wall switch installed in the unit. A bag containing the wall
switch, cover plate and flame control solenoid is located
in the manual bag assembly on the right side of the unit.
• A110-120 VAC circuit for this product must be protected
with ground-fault circuit-interrupter protection, in
compliance with the applicable electrical codes, when
it is installed in locations such as in bathrooms or near
sinks.
Follow the “Determine Location” and “Wiring the Wall
Switch” sections of the WSK-MLT instructions.
Install the flame control solenoid by following Steps 5 - 11
in the “Installing the Control Box” section of the WSK-MLT
instructions.
• Low voltage and 110 VAC voltage cannot be shared
within the same wall box.
WARNING! Risk of Shock or Explosion! DO NOT wire
110V to the valve or to the appliance wall switch. Incorrect
wiring will damage controls.
Also carefully follow the “Setting Flame Height/Manifold
Pressure” section of the included instructions to properly
set the valve pressure. Operating instructions are also in-
cluded in the WSK-MLT instructions.
B. IntelliFire Ignition System Wiring
• Wire the appliance junction box to 110 VAC for proper
operation of the appliance.
WARNING! Risk of Shock or Explosion! DO NOT wire
IPI controlled appliance junction box to a switched circuit.
Incorrect wiring will override IPI safety lockout.
• Refer to Figure 12.1 IntelliFire Pilot Ignition (IPI) Wiring
Diagram.
• This appliance is equipped with an IntelliFire control valve
which operates on a 3 volt system.
• Plug the 3-volt AC transformer into the appliance junction
box to supply power to the unit OR install two D cell
batteries (not included) into the battery pack before use.
NOTICE: Batteries should not be placed in the battery
pack while using the transformer. Remove batteries before
using the transformer, and unplug the transformer before
installing the batteries. Battery polarity must be correct or
module damage will occur. Batteries should not be placed
in the battery pack until needed.
NOTICE: Do not use battery back up without removing
refractory panels and mesh. Failure to do so may result in
damage to components. Use battery back up to operate
appliance only during power outage.
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
41
WIRES WITH LABEL “FOR USE WITH
REMOTE OR WALL SWITCH ONLY”
(LOCATED UNDER FIREPLACE)
DETAIL A
BATTERIES
BLACK
RED
GREEN
YELLOW (HNG)
WHITE (HTL)
ORANGE
RED
GREEN
BATTERY
REAR VIEW
GROUND
BLACK
IPI
VALVE
1
2
3
4
5
6
7
8
G
Y
R
IPI PILOT
IPI
MODULE
BROWN
BROWN
RED
BROWN
BROWN
3V DC
FLAME
BLACK
SOLENOID
FRONT VIEW
RED
RED
FLAME ON
ORANGE
ORANGE
BLACK
FLAME HIGH/LOW
YELLOW
FACTORY
CONNECTED
TOGETHER
AC
PLUG
ADAPTER WIRES
YELLOW
FAN THERMOSTAT
BLACK
GROUND
PIGTAIL
GREEN
FAN
CONNECTION
AUX
CONNECTION
FIREBOX LIGHTS
*
BLACK
H O T
WHITE
GROUND
CONTINUOUS
110VAC
SUPPLY
N E U T R A L
NOTE: BATTERY PACK AND SWITCH ARE LOCATED IN THE
MANUAL BAG. THE BATTERY PACK IS TO BE USED ONLY IN
THE CASE OF A POWER OUTAGE.
DETAIL A
ON/OFF ROCKER SWITCH
BATTERIES
NOTE: APPLIANCE WILL NOT OPERATE UNLESS PROPERLY
GROUNDED. *MUST ORDER PLUG-ADP SEPARATELY IF
USING THE HEAT-ZONE.
RED
BLACK
GREEN
NOTE: IGNITION MODULE, VALVE, PILOT
AND WALL SWITCH OPERATE ON 3 VOLTS.
Figure 12.1 IntelliFire Pilot Ignition (IPI) Wiring Diagram
42
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
PVK-80 POWERVENT
(GREEN)
JUNCTION BOX
(WHITE)
(BLACK)
(BROWN)
(BROWN)
(BROWN)
(RED)
(WHITE)
(BLACK)
(BROWN)
(RED)
WHITE (HTL)
YELLOW (H&G)
(GREEN)
(ORANGE)
RED
GROUND
BLACK
GREEN
IPI
VALVE
IPI PILOT
(BROWN)
(BROWN)
REAR VIEW
G
Y
R
IPI
MODULE
(RED)
(BLACK)
(RED)
(BLACK)
3V DC
FLAME
SOLENOID
FRONT VIEW
(RED)
FLAME ON
(RED)
(ORANGE)
(ORANGE)
(YELLOW)
FACTORY
CONNECTED
TOGETHER
FLAME HIGH/LOW
(BLACK)
(WHITE)
(BLACK)
FIREBOX
(YELLOW)
FAN
CONNECTION
(GROUND)
FAN THEMOSTAT
(BLACK)
TO HEAT ZONE
AC
PLUG
(BLACK)
AUX
CONNECTION
PLUG-ADP
BACK
LIGHT 1
GROUND PIGTAIL
GREEN
NOTE 1: BROWN AND RED WIRES FROM
PVK-80 ARE FOR THE VACUUM SWITCH
NOTE 2: BLACK, WHITE AND GREEN WIRES
RUN PVK-80 MOTOR.
BACK
LIGHT 2
NOTE 3: GREEN WIRE FROM PVK-80 SHOULD
TIE INTO GROUND A THE JUNCTION BOX
WHERE 110V SERVICE IS REQUIRED.
Figure 12.2 IPI Wiring diagram for optional PVK-80 power vent termination cap
D. Electrical Service and Repair
WARNING! Risk of Shock! Label all wires prior to dis-
connection when servicing controls. Wiring errors can
cause improper and dangerous operation. Verify proper
operation after servicing.
WARNING! Risk of Shock! Replace damaged wire with
type 105° C rated wire. Wire must have high temperature
insulation.
E. Junction Box Installation
If the box is being wired from the INSIDE of the appli-
ance:
• Remove the screw attaching the junction box/receptacle
to the outer shell, rotate the junction box inward to dis-
engage it from the outer shell (see Figure 12.4).
• Pull the electrical wires from outside the appliance through
the opening into the valve compartment and secure wires
with a Romex connector. See Figure 12.4.
• Make all necessary wire connections to the junction
box/receptacle and reattach the junction box/receptacle
to the outer shell.
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
43
Finishing
13
A. Splatter Guard
The splatter guard is a piece of corrugated material
used to protect the appliance during the installation
process before finishing work on the whole hearth is
complete. Splatter guards may be factory installed or
accompany the door of the unit, depending on the fire-
place model. Splatter guards must be removed before
appliance is fired.
WARNING! Risk of Fire! Close the ball valve before in-
stalling the splatter guard to prevent accidental lighting.
Remove the splatter guard before lighting the appliance.
Step 1. Turn off gas to valve. Red gas shutoff knob is
located on ball valve. Disconnect the 3 volt transformer
from the junction box. See Figure 13.1.
Figure 13.3
Figure 13.1
To install the Splatter Guard:
Step 2. Crease the bottom and side flaps of the splatter
guard using the scored line as the guide. See Figure 13.2.
Figure 13.2
Step 3. Place the top side of splatter guard behind the left
and right panel brackets and in front of the glass. See
Figure 13.3.
44
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
Combustible Mantel Legs or Wall Projections
B. Mantel and Wall Projections
WARNING! Risk of Fire! Comply with all minimum clear-
ances as specified. Framing closer than the minimums list-
ed must be constructed entirely of noncombustible materials
(i.e., steel studs, concrete board, etc.)
Combustible Mantels
4 INCH
MINIMUM
UNLIMITED
NON-COMBUSTIBLE
MATERIAL
3-1/2 IN.
FINISH WALL
COMBUSTIBLE
NO COMBUSTIBLES
IN THIS AREA
Figure 13.5 Combustible Mantel Leg or Wall Projections
(Acceptable on both sides of opening)
COMBUSTIBLE
FRAMING
39 IN.
METAL PANELS
(PROVIDED)
C. Facing Material
• The appliance front metal surfaces may be covered with
non-combustible materials only.
COMBUSTIBLE
PROJECTIONS
• Non-combustible materials MUST be placed around the
fireplace opening (see Figure 13.6)
12 IN.
10-1/2 IN.
9 IN.
7-1/2 IN.
6 IN.
4-3/4 IN.
3 IN.
11-12 IN.
12 IN.
MIN.
• Facing and/or finishing materials must not interfere with
air flow through louvers, operation of louvers and door
or removal of the right, left and bottom refractory panel
for service.
8 IN. MIN.
6 IN. MIN.
NON-COMBUSTIBLE
FACING MATERIAL
MIN. 1/2 IN. THICKNESS
• Facing and/or finishing materials must never overhang
into the glass opening.
TOP OF FIREPLACE
OPENING
• Observe all clearances when applying combustible
materials.
Height
above
opening
in.
mm 152 178 203 228 254 279
in. 4-3/4 7-1/2 10-1/2 12
mm 76 121 152 191 228 267 305
6
7
8
9
10
11
12
305
• Seal joints between the finished wall and appliance top
and sides using a 300 °F minimum sealant. Refer to
Figure 13.7.
Horizontal
Mantel
distance
3
6
9
WARNING! Risk of Fire! DO NOT apply combustible
materials beyond the minimum clearances. Comply with
all minimum clearances to combustibles as specified in
this manual. Overlapping materials could ignite and will
interfere with proper operation of doors and louvers.
Figure 13.4 Minimum Vertical and Maximum Horizontal
Dimensions of Combustibles
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
45
NON-COMBUSTIBLE
ZONE
VIEW FROM TOP OF APPLIANCE
7-1/2 INCH MINIMUM
NON-COMBUSTIBLE
MATERIAL
COMBUSTIBLE OK
43 in.
FINISH
WALL
NON-COMBUSTIBLE
FACING MATERIAL
METAL
PANELS
60 in.
60 in.
Figure 13.6 Noncombustible Facing Diagram
D. Finishing Materials Requirements
43 in.
Note: Optional firescreen sits out 1-1/2 inches from the
face of the fireplace. When using thin finishing material, you
may want to use thicker non-combustible backer board to
bring the finishing material flush with the fire screen. This
is not required.
HIGH TEMPERATURE (300º F /149º C MIN.)
TOP AND SIDE SEAL JOINTS
• Use the two metal panels shipped with fireplace.
Figure 13.7 Non-combustible Finishing Material Requirements
• Unscrew the four screws holding two panels together.
• Slide the two tapered tabs on bottom of each panel into
slots of top surround.
• Secure panels with sheet metal screws previously
removed from panels.
The metal panels will cover the width of appliance and
height of appliance to header board (11-1/2 inch).
• Cover entire face of appliance with non-combustible
materials prior to applying finishing material, such as
brick, stone or tile. See Figure 9.2, 9.3, 13.6 and 13.7.
• The finishing material must NEVER pass the 1/2 inch
metal edge around the opening and overhang into the
glass opening.
46
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
Appliance Setup
14
A. Remove Fixed Glass Assembly
E. Ember Placement
See Section 14.G.
WARNING! Risk of Explosion! Follow ember placement
instructions in manual. DO NOT place embers directly over
burner ports. Replace ember material annually. Improperly
placed embers interfere with proper burner operation.
B. Remove the Shipping Materials
Remove shipping materials from inside or underneath the
firebox.
Ember material is shipped with this gas appliance. To place
the ember material:
C. Clean the Appliance
• Remove the ash lip that is located in front of the glass.
• Remove the side panels located in front of the glass.
Clean/vacuum any sawdust that may have accumulated
inside the firebox or underneath in the control cavity.
• Remove the pull mesh firescreen by unhooking from the
fireplace.
D. Accessories
Install approved accessories per instructions included
with accessories. Contact your dealer for a list of ap-
proved accessories.
• Pull and release the six glass latches (3 per side) located
on the sides of the glass frame.
• Grasping the upper lip with one hand and the lower
lip with the other, pull the bottom of the glass out first.
Guide the bottom while letting the top drop down under
the top of the opening (see Section 14.G Fixed Glass
Assembly).
WARNING! Risk of Fire and Electric Shock! Use ONLY
Hearth & Home Technologies-approved optional acces-
sories with this appliance. Using non-listed accessories
could result in a safety hazard and will void the warranty.
• There are two types of ember shipped with the unit.
Embers for the burner surface and Mystic Embers for
the floor of the unit.
• Do NOT place embers between log #3 and log #4. They
may disrupt the flames and are not visible.
• Place Mystic Embers on the floor of unit. Use Mystic
Embers to hide the pilot wires on left side of the
burner.
NOTICE: Do NOT place Mystic Embers over lighted area
of lens. Lens may melt if covered.
• Save the remaining ember materials for use during
fireplace servicing.
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
47
F. Install the Log Assembly
LOG PLACEMENT INSTRUCTIONS
Log Set Assembly: LOGS-ESCAPE42
Models: Escape-42DV
If the gas logs have been factory
installed they should not need to
be positioned. If the logs have been
packaged separately, refer to the
following instructions.
NOTE: If sooting occurs, the logs
may need to be repositioned slightly
to avoid excessive flame impinge-
ment.
3
5
4
6
CAUTION: Logs are fragile!
Carefully remove the logs from the
packaging.
1
8
7
1
NOTE: If logs rub against one an-
other during positioning, the white
inner material may become visible.
Touch-up paint may be applied to
the white areas using a small brush
or swab. DO NOT spray paint di-
rectly on surface of the logs. Refer-
ence service parts list for log touch-
up paint.
1
2
2
Step 1.
NOTE: If bulb and orange lens are
already installed, proceed to Step 2.
Remove the bulb from its packag-
ing and locate the sockets installed
in the square cut outs in the firebox
floor. The contacts on the bulb
push into the two small holes in the
socket top, as shown.
Place the framed orange lens on
top of the firebox floor covering the
bulb as shown. The four tabs on
the lens frame go into the square
cut out to help locate the lens.
48
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 2.
Place the grate onto the burner. The
back of the right tine drops into the
hole on the right rear of the burner.
Line the grate up so it is parallel with
the front of the firebox. Be sure to
push the grate all the way down to
the floor.
LOG #1
(SRV2012-081) (Three):
There are quantity three (3) of Log
#1. Place one of the logs on the floor
of the fireplace on the left side of the
grate between the firebox and the
left grate tine. Place the second log
on the right side of the burner be-
tween the burner and the right grate
tine. The second log can be slightly
resting on the edge of the burner.
Place third log on top of the left side
of the burner. The burner ports will
be around the log. Do NOT cover
any burner ports with the log.
1
1
1
Place the right end of the second log on the pilot bracket.
The left end of the log should rest on the base of the firebox
See Figure B.
LOG #2 (SRV2012-082) (Two):
There are quantity 2 (two) of Log #2. Place one of the logs
on the right side of the burner on the floor (see Figure A).
The log will be in front of the orange Kapton lens.
Figure A
Figure B
2
2
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
49
LOG #3
(SRV2052-083):
Place Log #3 onto the back of the
burner. The log sits on top of the
burner surface. The back of the log
is pushed up against the back metal
wall of the burner and the left end
of the log is flush with the left edge
of the metal wall.
FLUSH END
3
LOG #4
(SRV2012-084):
Place Log #4 on top of the burner in
front of Log 3. The triangle shaped
groove in the bottom fits onto the
right grate tine. The left end of the
log will fit the contour of the burner
between the ports. DO NOT cover
the burner ports.
3
4
LOG #5
(SRV2012-085):
Place Log #5 in front of Log #4. The
groove in the bottom end of the log
fits into the right vertical grate tine.
The back of the log rests in the
small flat spot on top of Log #3.
3
5
4
50
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
LOG #6
(SRV2052-086):
Place log #6 on the left side of the
grate with the groove on the end of
the log fitting into the vertical left
grate tine. The other end sits on
the flat spot of log #3.
6
3
LOG #7
(SRV2012-087):
Place log #7 on top of log #6. The
groove in the front side of the log
fits into the second vertical tine
from the left of the grate. The
center of the log rests in the flat
spot on log #6.
7
6
LOG #8
(SRV2012-088):
Place Log #8 on top of Log #5.
The flat bottom of Log #8 sits on
the large flat area of Log #5. The
burned end of Log #8 rests on the
second vertical tine from the right
of the grate. The tine fits on the
burned out groove on the left end
of the log.
5
8
Final Step:
Place MYSTIC EMBERS gener-
ously around on the floor of the
fireplace. Do NOT put Mystic em-
bers on the burner surface around
the ports. Place embers around
the pilot wires to disguise the wires
from view.
2052-945B
51
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
G. Fixed Glass Assembly
I. Air Shutter Setting
WARNING! Risk of Asphyxiation! Handle fixed glass
assembly with care. Inspect the gasket to ensure it is
undamaged and inspect the glass for cracks, chips or
scratches.
Air shutter settings should be adjusted by a qualified ser-
vice technician at the time of installation. The air shutter
is set at the factory for minimum vertical vent run. Adjust
air shutter for longer vertical runs.
• DO NOT strike, slam or scratch glass.
NOTICE: If sooting occurs, provide more air by opening
the air shutter.
• DO NOT operate fireplace with glass removed, cracked,
broken or scratched.
Air Shutter Settings
• Replace as a complete assembly.
NG
3/8 in.
N/A
LP
N/A
Removing Fixed Glass Assembly
ESCAPE42-DV
• Remove the ash lip that is located in front of the glass.
ESCAPE42-DVLP
11/16 in.
• Remove the side panels located in front of the glass.
• Remove the pull mesh firescreen by unhooking from the
fireplace.
• Pull and release the six glass latches (3 per side) located
on the sides of the glass frame.
• Grasping the upper lip with one hand and the lower lip
with the other, pull the bottom of the glass out first. Guide
the bottom while letting the top drop down under the top
of the opening (see Figure 14.1).
Replacing Fixed Glass Assembly
• Replace the glass door on the appliance. Pull out and
latch the six glass assembly latches into the groove on
the glass frame.
UPPER
LIP
GLASS
CLIP
Figure 14.1 Fixed Glass Assembly
H. Install the Mesh
The pull-type firescreen hangs on the three hanger brack-
ets located above the glass.
52
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
15
With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do
experience a problem, this troubleshooting guide will assist a qualified service technician in the diagnosis of a problem and
the corrective action to be taken. This troubleshooting guide can only be used by a qualified service technician. Contact
your dealer to arrange a service call by a qualified service technician.
A. IntelliFire Ignition System
Symptom
Possible Cause
Corrective Action
1. Pilot won’t light.
The ignitor/module
makes noise, but no
spark.
A. Incorrect wiring.
Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor are
connected to correct terminals on module and pilot assembly.
B. Loose connections or electrical
shorts in the wiring.
Verify no loose connections or electrical shorts in wiring from mod-
ule to pilot assembly. Verify connections underneath pilot assem-
bly are tight; also verify connections are not grounding out to metal
chassis, pilot burner, pilot enclosure, mesh screen if present, or any
other metal object.
C. Ignitor gap is too large.
D. Module.
Verify gap of igniter to right side of pilot hood. The gap should be
approximately .17 in. or 1/8 in. (3 mm).
Turn ON/OFF rocker switch or wall switch to OFF position. Remove
ignitor wire “I” from module. Place a grounded wire about 3/16 in. (5
mm) away from “I” terminal on module. Place ON/OFF rocker switch
or wall switch in ON position. If there is no spark at “I” terminal module
must be replaced. If there is a spark at “I” terminal, module is fine.
Inspect pilot assembly for shorted sparker wire or cracked insulator
around electrode. Replace pilot if necessary.
2. Pilot won’t light,
there is no noise or
spark.
A. No power or transformer installed
incorrectly.
Verify that transformer is installed and plugged into module. Check
voltage of transformer under load at spade connection on module
with ON/OFF switch in ON position. Acceptable readings of a good
transformer are between 3.2 and 2.8 volts AC.
B. A shorted or loose connection in
wiring configuration or wiring har-
ness.
Remove and reinstall the wiring harness that plugs into module.
Verify there is a tight fit. Verify pilot assembly wiring to module. Re-
move and verify continuity of each wire in wiring harness. Replace
any damaged components.
C. Improper wall switch wiring.
D. Module not grounded.
Verify that 110/VAC power is “ON” to junction box.
Verify black ground wire from module wire harness is grounded to
metal chassis of appliance.
E. Module.
Turn ON/OFF rocker switch or wall switch to OFF position. Remove
ignitor wire “I” from module. Place ON/OFF rocker switch or wall
switch in ON position. If there is no spark at “I” terminal module
must be replaced. If there is a spark at “I” terminal, module is fine.
Inspect pilot assembly for shorted sparker wire or cracked insulator
around electrode.
3. Pilot sparks, but
Pilot will not light.
A. Gas supply.
Verify that incoming gas line ball valve is “open”. Verify that inlet
pressure reading is within acceptable limits.
B. Ignitor gap is too large.
C. Module is not grounded.
Verify gap of igniter to right side of pilot hood. The gap should be
approximately .17 in. or 1/8 in. (3 mm).
Verify module is securely grounded to metal chassis of appliance.
D. Module voltage output / Valve/Pilot Verify battery voltage is at least 2.7 volts. Replace batteries if volt-
solenoid ohms readings. age is below 2.7.
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
53
IntelliFire Ignition System - (continued)
Symptom
Possible Cause
Corrective Action
A. A shorted or loose connection in flame
Verify all connections to wiring diagram in manual. Verify
connections underneath pilot assembly are tight. Verify con-
nections are not grounding out to metal chassis, pilot burn-
er, pilot enclosure or screen if present, or any other metal
object.
4. Pilot lights but contin-
ues to spark, and main
burner will not ignite.
(If the pilot continues
to spark after the
pilot flame has been lit,
flame rectification has
not occurred.)
sensing rod.
B. Poor flame rectification or contaminated With fixed glass assembly in place, verify that flame is en-
flame sensing rod.
gulfing flame sensing rod on left side of pilot hood. Flame
sensing rod should glow shortly after ignition. Verify cor-
rect pilot orifice is installed and gas inlet is set to pressure
specifications. Clean flame sensing rod with emery cloth to
remove any contaminants that may have accumulated on
flame sensing rod.
C. Module is not grounded.
Verify module is securely grounded to metal chassis of ap-
pliance. Verify that wire harness is firmly connected to the
module.
D. Damaged pilot assembly or contami-
nated flame sensing rod.
Verify that ceramic insulator around the flame sensing rod
is not cracked, damaged, or loose. Verify connection from
flame sensing rod to white sensor wire. Polish flame sens-
ing rod with fine steel wool to remove any contaminants
that may have accumulated on flame sensing rod. Verify
continuity with a multimeter with ohms set at lowest range.
Replace pilot if any damage is detected.
E. Module.
Turn ON/OFF rocker switch or wall switch to OFF position.
Remove ignitor wire “I” from module. Place ON/OFF rocker
switch or wall switch in ON position. If there is no spark at “I”
terminal module must be replaced. If there is a spark at “I”
terminal, module is fine.
54
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Materials
16
A. Appliance Dimension Diagram
Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 5.
A
B
F
C
MINIMUM 24"
VERTICAL
REQUIRED
Ø D
E
M
G
L
H
GAS LINE
ACCESS
R
T
N
Q
I
K
S
O
P
OPTIONAL FIRESCREEN
SITS OUT 1-1/2 INCHES
FROM UNIT FACE
ELECTRICAL
ACCESS
J
Location Inches Millimeters
Location Inches Millimeters
A
B
C
D
E
F
G
H
I
48
28-3/8
12
1219
722
305
202
12
K
L
11-5/8
3-5/8
1
296
91
M
N
O
P
Q
R
S
T
24
8
41-3/8
42
1052
1068
1445
939
1320
38
1/2
21
533
609
1831
66
56-7/8
37
24
72-1/8
2-5/8
4-1/4
52
1-1/2
40-3/8
J
107
1062
Figure 16.1 Appliance Dimensions
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
55
B. Vent Components Diagrams
Effective Length
Pipe
10-1/2 in.
(267 mm)
Inches
4
Millimeters
102
°
45
DVP4
Effective
Height/Length
DVP6
6
12
152
305
DVP12
DVP24
DVP36
DVP48
DVP6A
4-7/8 in.
( 276 mm)
24
610
36
914
10-7/8 in.
(276 mm)
48
1219
76 to 152
DVP Pipe (see chart)
3 to 6
DVP45 (45º Elbow)
DVP12A 3 to 12 76 to 305
DVP12MI 3 to 12 76 to 305
DVP24MI 3 to 24 76 to 610
11-3/8 in.
(289 mm)
10 in.
(254 mm)
1 in.
(25 mm)
7-3/8 in.
(187 mm)
1-1/4 in. (32 mm)
10 in.
(254 mm)
9-1/4 in.
(235 mm)
Assembled
Height: 24 in./610 mm
Diameter: 10 in./254 mm
1/2 in. TYP
(13 mm)
13-1/4 in.
(337 mm)
DVP-AS2
DVP-FS (Ceiling Firestop)
DVP90ST (90° Elbow)
12 in.
(305 mm)
1 in.
(25 mm)
8 in.
(203 mm)
1- 1/2 in.
(38 mm)
10 in.
(254 mm)
14 in.
(356 mm)
UP
5 in.
(127 mm)
12 in.
(305 mm)
6 in.
(152 mm)
DVP-HVS (Vent Support)
DVP-WS (Wall Shield Firestop)
Figure 16.2 DVP vent components
56
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Vent Components Diagrams (continued)
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). The heat shield is designed to be
used on a wall 4 in. to 7-1/4 in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm) the
existing heat shields must be field trimmed. If wall thickness is greater than 7-1/4 in. (184 mm) a DVP-HSM-B
will be required.
8 in.
(203 mm)
Heat
Shield
15-1/8 in.
(384 mm)
Minimum
Effective Length
Maximum
Effective Length
Term Cap
Trap1
Max
Effective
Length
12 in.
(305 mm)
3-1/8 in.
79 mm
4-5/8 in.
117 mm
9-3/8 in.
238 mm
DVP-TRAP
Horizontal Termination Cap
5-3/8 in.
137 mm
Trap2
DVP-TRAP2
DVP-TRAP1
DVP-TRAPK2
DVP-TRAPK1
DVP-HPC2
DVP-HPC1
Figure 16.3 DVP vent components
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
57
B. Vent Components Diagrams (continued)
31 in.
(787 mm)
13-1/4 in.
(367 mm)
24-5/8 in.
(625 mm)
27-1/2 in.
(127 mm)
24-5/8 in.
(625 mm)
13-1/4 in.
(367 mm)
RF6M
RF12M
Roof Flashing Multi-pak
Roof Flashing Multi-pak
5 in.
(127 mm)
11-7/8 in.
(302 mm)
5 in.
(127 mm)
13-3/4 in.
(349 mm)
13-7/8 in.
(352 mm)
13-3/4 in.
(349 mm)
DVP-BEK2
DVP-HPC Cap Brick Extension
BEK
Trap Cap Brick Extension
11-5/8 in.
(295 mm)
12-1/8 in.
(308 mm)
7-1/8 in.
(181 mm)
5-3/4 in.
(146 mm)
DVP-TRAPFL
COOL-ADD
Cap Shield
Flashing
13-7/8 in.
(352 mm)
9-1/2 in.
(241 mm)
26 in.
660 mm
14 in.
(356 mm)
DVP-HSM-B
Extended Heat Shield
DRC-RADIUS
Cap Shield
Figure 16.4 DVP vent components
58
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Vent Components Diagrams (continued)
7-3/8 in.
(187 mm)
1-1/2 in.
(38 mm)
3-7/8 in.
(98 mm)
17-3/4 in.
14 in.
(356 mm)
(451 mm)
10-1/2 in.
(267 mm)
DVP-TV
VerticalTermination Cap
12 in.
(305 mm)
DVP-TB1
BasementVent Cap
12 in.
305 mm
9 in.
12-1/2 in.
(317 mm)
(229 mm)
2-3/4 in.
(70 mm)
7-1/4 in.
(184 mm)
12-1/2 in.
(318 mm)
11-1/2 in.
(292 mm)
5-1/4 in.
(133 mm)
12-1/4 in.
(311 mm)
DVP-TVHW
VerticalTermination Cap (Highwind)
16 in.
(406 mm)
PVK-80
(For use with IPI and DSI appliances only.)
7-1/4 in.
(184 mm)
14 in.
(356 mm)
16-7/8 in.
(429 mm)
1 in.
(25 mm)
12 in.
(305 mm)
14 in.
(356 mm)
7-1/8 in.
12-1/8 in.
(181 mm)
(314 mm)
3/8 in. (10 mm)
1 in. (25 mm)
8-3/4 in.
(222 mm)
7-3/4 to 10-3/8 in.
(197 to 264 mm)
1-5/8 in.
(41 mm)
DVP-FBHT
FireBrickTermination Cap
DVP-HPC
High Performance Cap
Figure 16.5 DVP vent components
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
59
B. Vent Components Diagrams (continued)
Optional Wire Harness
13-5/8 IN.
346 mm
DESCRIPTION
PART NUMBER
PVI-WH10
EFFECTIVE LENGTH
32 IN. (813 mm) MIN.
35 IN. (889 mm) MAX.
10 ft. PV Wire Harness
20 ft. PV Wire Harness
40 ft. PV Wire Harness
60 ft. PV Wire Harness
80 ft. PV Wire Harness
100 ft. PV Wire Harness
PVI-WH20
PVI-WH40
12-1/2 IN.
318 mm
PVI-WH60
PVI-WH80
PVI-WH100
20-3/4 IN.
527 mm
Note: Wire harnesses required to power the PVI-SLP
connect to the appliance and are ordered separately
from PVI-SLP. Contact your dealer to order.
PVI-SLP
Power Vent Inline
16 IN.
406 mm
4-1/2 IN.
114 mm
15 IN.
(381 mm)
9-3/16 IN.
(233 mm)
13-5/8
(346 mm)
16-11/16 IN.
424 mm
16-11/16 IN.
(424 mm)
12-1/2 IN.
(318 mm)
SLP-LPC
SLP Low Profile Cap
Figure 16.6 Vent Components
60
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
D. Contact Information
Heat & Glo, a brand of Hearth & Home Technologies Inc.
7571 215th Street West, Lakeville, MN 55044
Please contact your Heat & Glo dealer with any questions or concerns.
For the location of your nearest Heat & Glo dealer,
- NOTES -
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
NOTICE
DO NOT DISCARD THIS MANUAL
• Important operating
and maintenance
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
• Leave this manual with
party responsible for use
and operation.
This product may be covered by one or more of the following patents: (United States) 5328356, 5601073, 5613487,
5647340, 5890485, 5941237, 5947112, 5996575, 6006743, 6019099, 6053165, 6145502, 6170481, 6374822, 6484712,
6601579, 6769426, 6863064, 7077122, 7098269, 7258116, 7470729 or other U.S. and foreign patents pending.
2000-945
Printed in U.S.A. - Copyright 2011
64
Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11
Download from Www.Somanuals.com. All Manuals Search And Download.
|