Para obtener un ejemplar en Español de este
Pour demander un exemplaire en français de ce Manuel
Owner’s Manual
Installation and Operation
Model:
Bravo
CAUTION
DO NOT DISCARD THIS MANUAL
• Important operating
and maintenance
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
• Leave this manual with
party responsible for use
and operation.
WARNING
WARNING: If the information in these
instructions is not followed exactly, a fire
or explosion may result causing property
damage, personal injury, or death.
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
Hot glass will cause burns.
• Do not touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• Do not store or use gasoline or other flam-
mable vapors and liquids in the vicinity of
this or any other appliance.
• CAREFULLY SUPERVISE children in same room as
fireplace.
• Alert children and adults to hazards of high temperatures.
• What to do if you smell gas
- Do not try to light any appliance.
High temperatures may ignite clothing or other flammable
materials.
• Keep clothing, furniture, draperies and other flammable
materials away.
- Do not touch any electrical switch. Do not
use any phone in your building.
- Immediately call your gas supplier from a
neighbor’s phone. Follow the gas suppli-
er’s instructions.
This appliance has been supplied with an integral barrier
to prevent direct contact with the fixed glass panel. DO
NOT operate the appliance with the barrier removed.
- If you cannot reach your gas supplier, call
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
the fire department.
• Installation and service must be performed
by a qualified installer, service agency, or the
gas supplier.
In the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas fitter.
See Table of Contents for location of additional Commonwealth
of Massachusetts requirements.
This appliance may be installed as an OEM installation in
manufactured home (USA only) or mobile home and must be
installed in accordance with the manufacturer’s instructions and
the manufactured home construction and safety standard, Title
24 CFR, Part 3280 or Standard for Installation in Mobile Homes,
CAN/CSA Z240MH.
Installation and service of this appliance should be
performed by qualified personnel. Hearth & Home
Technologies suggests NFI certified or factory trained
professionals, or technicians supervised by an NFI
certified professional.
This appliance is only for use with the type(s) of gas indicated
on the rating plate.
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Table of Contents
1 Listing and Code Approvals
10 Electrical Information
A. Appliance Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
B. Glass Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
C. BTU Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
D. High Altitude Installations. . . . . . . . . . . . . . . . . . . . . . . . . . 4
E. Non-Combustible Materials Specification. . . . . . . . . . . . . . 4
F. Combustible Materials Specification . . . . . . . . . . . . . . . . . 4
G. Requirements for the Commonwealth of Massachusetts. . 5
A. Recommendation for Wire . . . . . . . . . . . . . . . . . . . . . . . . 29
B. Connecting to the Appliance. . . . . . . . . . . . . . . . . . . . . . . 29
C. Intellifire Ignition System Wiring . . . . . . . . . . . . . . . . . . . 29
D. Wall Switch (Required). . . . . . . . . . . . . . . . . . . . . . . . . . . 29
E. Junction Box Installation. . . . . . . . . . . . . . . . . . . . . . . . . . 31
11 Finishing
A. Mantel Projections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
B. Facing Material. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
C. Finishing Styles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
2 Getting Started
A. Design and Installation Considerations . . . . . . . . . . . . . . . 6
B. Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . . . . 6
C. Inspect Appliance and Components. . . . . . . . . . . . . . . . . . 6
12 Appliance Setup
A. Remove Shipping Materials . . . . . . . . . . . . . . . . . . . . . . . 36
B. Clean the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
C. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
D. Lava Rock and Ember Placement . . . . . . . . . . . . . . . . . . 36
E. Positioning the Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
F. Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
G. Grilles and Trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
H. Air Shutter Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
3 Framing and Clearances
A. Selecting Appliance Location . . . . . . . . . . . . . . . . . . . . . . . 7
B. Constructing the Appliance Chase. . . . . . . . . . . . . . . . . . . 8
C. Clearances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
D. Mantel Projections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4 Termination Locations
A. Vent Termination Minimum Clearances . . . . . . . . . . . . . . 10
13 Operating Instructions
5 Vent Information and Diagrams
A. Before Lighting Appliance. . . . . . . . . . . . . . . . . . . . . . . . . 41
B. Lighting Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
C. After Appliance is Lit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
D. Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . 43
A. Vent Table Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
B. Use of Elbows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
C. Measuring Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
D. Vent Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
14 Troubleshooting
6 Vent Clearances and Framing
A. Intellifire Ignition System . . . . . . . . . . . . . . . . . . . . . . . . . 44
A. Pipe Clearances to Combustibles . . . . . . . . . . . . . . . . . . 18
B. Wall Penetration Framing . . . . . . . . . . . . . . . . . . . . . . . . 18
C. Vertical Penetration Framing . . . . . . . . . . . . . . . . . . . . . . 19
15 Maintaining and Servicing Appliance
A. Maintenance Tasks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
7 Appliance Preparation
16 Reference Materials
A. Securing and Leveling the Appliance. . . . . . . . . . . . . . . 20
A. Appliance Dimension Diagram. . . . . . . . . . . . . . . . . . . . . 48
B. Vent Components Diagrams . . . . . . . . . . . . . . . . . . . . . . 49
C. Service Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
D. Limited Lifetime Warranty. . . . . . . . . . . . . . . . . . . . . . . . . 56
E. Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
8 Installing Vent Pipe
A. Assembly of Vent Sections (DVP Pipe) . . . . . . . . . . . . . . 21
B. Disassembly of Vent Sections . . . . . . . . . . . . . . . . . . . . . 23
C. Installing Heat Shield and Horizontal Termination Cap . . 24
D. Installing Roof Flashing and Vertical Termination Cap. . . 25
9 Gas Information
A. Fuel Conversions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
B. Gas Pressures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
C. Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Listing and Code Approvals
1
A. Appliance Certification
C. BTU Specifications
Orifice
Size
(DMS)
Maximum
Input BTUH
Models
MODELS: Bravo
(U.S. or Canada)
LABORATORY: Underwriters Laboratories, Inc. (UL)
TYPE: Direct Vent Gas Appliance Heater
STANDARD: ANSI Z21.88-2000 • CSA2.33-M2000 • UL307B
US
23,000
20,700
23,000
20,700
42
43
53
54
(0-2000 FT)
Bravo (NG)
Bravo (LP)
CANADA
(2000-4500 FT)
US
(0-2000 FT)
This product is listed to ANSI standards for “Vented Gas
Appliance Heaters” and applicable sections of “Gas Burn-
ing Heating Appliances for Manufactured Homes and
Recreational Vehicles”, and “Gas FiredAppliances for Use
at High Altitudes”.
CANADA
(2000-4500 FT)
D. High Altitude Installations
U.L. Listed gas appliances are tested and approved without
requiring changes for elevations from 0 to 2000 feet in the
U.S.A. and Canada.
NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.
This appliance is tested and approved as either supplemental
room heat or as a decorative appliance. It should not be fac-
tored as primary heat in residential heating calculations.
When installing this appliance at an elevation above 2000
feet, it may be necessary to decrease the input rating by
changing the existing burner orifice to a smaller size. Input
rate should be reduced by 4% for each 1000 feet above
a 2000 foot elevation in the U.S.A., or 10% for elevations
between 2000 and 4500 feet in Canada. If the heating
value of the gas has been reduced, these rules do not
apply. To identify the proper orifice size, check with the
local gas utility.
This model may be installed in a bedroom or bed-sitting
room in the USA and Canada.
B. Glass Specifications
Hearth & Home Technologies appliances manufactured with
tempered glass may be installed in hazardous locations
such as bathtub enclosures as defined by the Consumer
Product Safety Commission (CPSC). The tempered glass
has been tested and certified to the requirements of ANSI
Z97.1 and CPSC 16 CFR 1202 (Safety Glazing Certification
Council SGCC# 1595 and 1597. Architectural Testing, Inc.
Reports 02-31919.01 and 02-31917.01).
If installing this appliance at an elevation above 4500 feet
(in Canada), check with local authorities.
WARNING
This statement is in compliance with CPSC 16 CFR
Section 1201.5 “Certification and labeling requirements”
which refers to 15 U.S. Code (USC) 2063 stating “…Such
certificate shall accompany the product or shall otherwise
be furnished to any distributor or retailer to whom the
product is delivered.”
Do NOT use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system
and any gas control which has been under water.
Some local building codes require the use of tempered
glass with permanent marking in such locations. Glass
meeting this requirement is available from the factory.
Please contact your dealer or distributor to order.
E. Non-Combustible Materials Specification
Material which will not ignite and burn. Such materials are
those consisting entirely of steel, iron, brick, tile, concrete,
slate, glass or plasters, or any combination thereof.
Note: This installation must conform with local codes. In the
absence of local codes you must comply with the National
Fuel Gas Code, ANSI Z223.1-latest edition in the U.S.A.
and the CAN/CGA B149 Installation Codes in Canada.
Materials that are reported as passing ASTM E 136,
Standard Test Method for Behavior of Materials in a
Vertical Tube Furnace at 750oC, shall be considered
non-combustible materials.
F. Combustible Materials Specification
Materials made of or surfaced with wood, compressed
paper, plant fibers, plastics, or other material that can ig-
nite and burn, whether flame proofed or not, or whether
plastered or unplastered shall be considered combustible
materials.
Heat & Glo Quality Systems
registered by SGS ICS
4
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
Inspection
Note: The following requirements reference various
Massachusetts and national codes not contained in this
document.
The state or local gas inspector of the side wall horizon-
tally vented gas fueled equipment shall not approve the
installation unless, upon inspection, the inspector ob-
serves carbon monoxide detectors and signage installed
in accordance with the provisions of 248 CMR 5.08(2)(a)1
through 4.
G. Requirements for the Commonwealth of
Massachusetts
For all side wall horizontally vented gas fueled equipment
installed in every dwelling, building or structure used in
whole or in part for residential purposes, including those
owned or operated by the Commonwealth and where the
side wall exhaust vent termination is less than seven (7)
feet above finished grade in the area of the venting, in-
cluding but not limited to decks and porches, the following
requirements shall be satisfied:
Exemptions
The following equipment is exempt from 248 CMR
5.08(2)(a)1 through 4:
• The equipment listed in Chapter 10 entitled “Equipment
Not Required To Be Vented” in the most current edition
of NFPA 54 as adopted by the Board; and
• Product Approved side wall horizontally vented gas fu-
eled equipment installed in a room or structure separate
from the dwelling, building or structure used in whole or
in part for residential purposes.
Installation of Carbon Monoxide Detectors
At the time of installation of the side wall horizontal vented
gas fueled equipment, the installing plumber or gas fitter
shall observe that a hard wired carbon monoxide detector
with an alarm and battery back-up is installed on the floor
level where the gas equipment is to be installed. In addi-
tion, the installing plumber or gas fitter shall observe that
a battery operated or hard wired carbon monoxide detec-
tor with an alarm is installed on each additional level of
the dwelling, building or structure served by the side wall
horizontal vented gas fueled equipment. It shall be the
responsibility of the property owner to secure the services
of qualified licensed professionals for the installation of
hard wired carbon monoxide detectors.
MANUFACTURER REQUIREMENTS
Gas Equipment Venting System Provided
When the manufacturer of Product Approved side wall
horizontally vented gas equipment provides a venting
system design or venting system components with the
equipment, the instructions provided by the manufacturer
for installation of the equipment and the venting system
shall include:
• Detailed instructions for the installation of the venting
system design or the venting system components; and
In the event that the side wall horizontally vented gas fu-
eled equipment is installed in a crawl space or an attic,
the hard wired carbon monoxide detector with alarm and
battery back-up may be installed on the next adjacent
floor level.
• A complete parts list for the venting system design or
venting system.
Gas Equipment Venting System NOT Provided
In the event that the requirements of this subdivision can
not be met at the time of completion of installation, the
owner shall have a period of thirty (30) days to comply
with the above requirements; provided, however, that dur-
ing said thirty (30) day period, a battery operated carbon
monoxide detector with an alarm shall be installed.
When the manufacturer of a Product Approved side wall
horizontally vented gas fueled equipment does not provide
the parts for venting the flue gases, but identifies “special
venting systems”, the following requirements shall be sat-
isfied by the manufacturer:
• The referenced “special venting system” instructions
shall be included with the appliance or equipment in-
stallation instructions; and
Approved Carbon Monoxide Detectors
Each carbon monoxide detector as required in accor-
dance with the above provisions shall comply with NFPA
720 and be ANSI/UL 2034 listed and IAS certified.
• The “special venting systems” shall be Product Ap-
proved by the Board, and the instructions for that sys-
tem shall include a parts list and detailed installation
instructions.
Signage
A metal or plastic identification plate shall be permanent-
ly mounted to the exterior of the building at a minimum
height of eight (8) feet above grade directly in line with the
exhaust vent terminal for the horizontally vented gas fu-
eled heating appliance or equipment. The sign shall read,
in print size no less than one-half (1/2) inch in size, “GAS
VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OB-
STRUCTIONS”.
A copy of all installation instructions for all Product Ap-
proved side wall horizontally vented gas fueled equip-
ment, all venting instructions, all parts lists for venting
instructions, and/or all venting design instructions shall
remain with the appliance or equipment at the completion
of the installation.
See Gas Connection section for additional Common-
wealth of Massachusetts requirements.
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Getting Started
2
A. Design and Installation Considerations
C. Inspect Appliance and Components
Heat & Glo direct vent gas appliances are designed to
operate with all combustion air siphoned from outside of
the building and all exhaust gases expelled to the outside.
No additional outside air source is required.
WARNING
Inspect appliance and components for damage.
Damaged parts may impair safe operation.
• Do NOT install damaged components.
• Do NOT install incomplete components.
• Do NOT install substitute components.
Report damaged parts to dealer.
CAUTION
Check building codes prior to installation.
• Installation MUST comply with local, regional, state and
national codes and regulations.
• Carefully remove the appliance and components from
the packaging.
• Consult local building, fire officials or authorities having jurisdic-
tion about restrictions, installation inspection, and permits.
• The vent system components and trim doors are shipped
in separate packages.
When planning an appliance installation, it’s necessary to
determine the following information before installing:
• The gas logs may be packaged separately and must be
field installed.
• Where the appliance is to be installed.
• The vent system configuration to be used.
• Gas supply piping.
• Report to your dealer any parts damaged in shipment,
particularly the condition of the glass.
• Read all of the instructions before starting the insta-
llation. Follow these instructions carefully during the
installation to ensure maximum safety and benefit.
• Electrical wiring.
• Framing and finishing details.
• Whether optional accessories—devices such as a wall
switch, or remote control—are desired.
WARNING
Hearth & Home Technologies disclaims any
responsibility for, and the warranty will be voided
by, the following actions:
WARNING
Keep appliance dry.
• Installation and use of any damaged appliance or vent
system component.
• Mold or rust may cause odors.
• Water may damage controls.
• Modification of the appliance or vent system.
• Installation other than as instructed by Hearth & Home
Technologies.
B. Tools and Supplies Needed
• Improper positioning of the gas logs or the glass door.
Before beginning the installation be sure that the following
tools and building supplies are available.
• Installation and/or use of any component part not approved
by Hearth & Home Technologies.
Any such action may cause a fire hazard.
Reciprocating saw
Pliers
Framing material
Hi temp caulking material
Gloves
Hammer
Phillips screwdriver
Framing square
Flat blade screwdriver Electric drill and bits (1/4 in.)
Plumb line
Level
Safety glasses
1/2 - 3/4 inch length, #6 or #8 Self-drilling screws
Voltmeter
Manometer
Tape measure
Noncorrosive leak check solution
6
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
Framing and Clearances
3
Note:
WARNING
• Illustrations reflect typical installations and are FOR
Fire Risk
DESIGN PURPOSES ONLY.
Provide adequate clearance:
• Around air openings
• Illustrations/diagrams are not drawn to scale.
• Actual installation may vary due to individual design
preference.
• To combustibles
• For service access
A. Selecting Appliance Location
Locate appliance away from traffic areas.
When selecting a location for your appliance it is important to
consider the required clearances to walls (see figure 3.1).
Note: For actual appliance dimensions refer to Section 16.
A
½
B
E
½
A
B
C
In addition to these framing dimensions, also reference the following sections:
• Clearances and Mantel Projections (Section 3.C and 3.D)
• Vent Clearances and Framing (Section 6).
B
Note: These dimensions
are for flush wall finishing
method. For a recessed
arch finishing method refer
to Option B in Finishing
(Section 11).
D
A
B
C
D
E
Inches
45-1/8
1146
34-3/8
873
63-7/8
1622
25-1/4
641
No maximum
Millimeters
Figure 3.1 Appliance Locations
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
7
high temp caulk or stuffed with unfaced insulation. If the
appliance is being installed on a cement slab, a layer of
plywood may be placed underneath to prevent conducting
cold up into the room.
B. Constructing the Appliance Chase
A chase is a vertical boxlike structure built to enclose the
gas appliance and/or its vent system. Vertical vents that run
on the outside of a building may be, but are not required
to be, installed inside a chase.
C. Clearances
Construction of the chase may vary with the type of building.
These instructions are not substitutes for the requirements
of local building codes. Local building codes MUST be
checked.
WARNING
Fire Risk.
Odor Risk.
Chases should be constructed in the manner of all outside
walls of the home to prevent cold air drafting problems.
The chase should not break the outside building envelope
in any manner.
• Install appliance on hard metal or wood surfaces
extending full width and depth of appliance.
• Do NOT install appliance directly on carpeting,
vinyl, tile or any combustible material other than
wood.
Walls, ceiling, base plate and cantilever floor of the chase
should be insulated. Vapor and air infiltration barriers
should be installed in the chase as per regional codes for
the rest of the home. Additionally, in regions where cold
air infiltration may be an issue, the inside surfaces may be
sheetrocked and taped for maximum air tightness.
WARNING
Fire Risk.
• Construct chase to all clearance specifications
in manual.
To further prevent drafts, the wall shield and ceiling firestops
should be caulked with high temperature caulk to seal gaps.
Gas line holes and other openings should be caulked with
• Locate and install appliance to all clearance
specifications in manual.
A
FROM
TOP OF
FINISHING
STRIP TO
CEILING
E
F
B
H
C
*
J
G
I
D
Clearance to Combustibles
A
B
C*
D
E
F
G
H
I
J
Rough
Rough
Opening
(Height)
Rough
Opening
(Depth)
Rough
Opening
(Width)
Clearance
to Ceiling
Combustible
Floor
Combustible
Flooring
Behind
Appliance
Sides of
Appliance
Front of
Appliance
Opening
(Vent Pipe)
Inches
10
44
25-1/4 35-3/8 34-7/8
641 699 886
0
0
0
0
1/2
13
1/2
13
36
Millimeters
25
1118
914
*For additional framing options and dimensions, see Section 11, Finishing.
Figure 3.2 Clearances to Combustibles
8
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
D. Mantel Projections
Note: All
measurements
in inches.
31
1 INCH
MINIMUM
TO
CEILING
18
17
VENT PIP E
16
15
14
9 1/8
MIN.
13
12
11
10
3 1/8
9
8
Figure 3.4 Clearances to Mantel Legs or Wall Projections
(Acceptable on both sides of opening.)
7
3 7/8
6
5
TOP OF
FINISHING STRIP
TOP OF
UNIT
Figure 3.3 Clearances to Mantels or Combustibles
above Appliance
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Termination Locations
4
A. Vent Termination Minimum Clearances
HORIZONTAL
OVERHANG
WARNING
2 FT.
MIN.
20 INCHES MIN.
VERTICAL
WALL
LOWEST
DISCHARGE
OPENING
Fire Risk.
Explosion Risk.
Inspect external vent cap regularly.
• Ensure no debris blocks cap.
GAS DIRECT VENT
TERMINATION CAP
X
• Combustible materials blocking cap may
ignite.
• Restricted air flow affects burner operation.
12
ROOF PITCH
IS X/ 12
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
WARNING
Fire Risk.
Roof Pitch
H (Min.) Ft.
Explosion Risk.
Flat to 6/12...........................................................1.0*
Over 6/12 to 7/12.................................................1.25*
Over 7/12 to 8/12.................................................1.5*
Over 8/12 to 9/12.................................................2.0*
Over 9/12 to 10/12...............................................2.5
Over 10/12 to 11/12.............................................3.25
Over 11/12 to 12/12.............................................4.0
Over 12/12 to 14/12.............................................5.0
Over 14/12 to 16/12.............................................6.0
Over 16/12 to 18/12.............................................7.0
Over 18/12 to 20/12.............................................7.5
Over 20/12 to 21/12.............................................8.0
Maintain vent clearance to combustibles as
specified.
• Do not pack air space with insulation or other
materials.
Failure to keep insulation or other materials
away from vent pipe may cause fire.
Measure vertical clearances from this surface.
* 3 foot minimum in snow regions
Figure 4.2 Minimum height from roof to lowest discharge
opening
Figure 4.2 specifies minimum vent heights for various
pitched roofs.
GAS, WOOD OR FUEL
OIL TERMINATION
B
GAS
TERMINATION
C
Measure horizontal clearances from this surface.
A
(See Figure 4.4 for specific clearances)
Figure 4.1
Gas
Termination
Wood & Fuel Oil
Termination
Comments
A
B
C
6 in.
20 in.
18 in.
20 in. min.
24 in. min.
18 in.
Horizontal distance between terminations
Distance to perpendicular wall
Vertical distance between terminations
Figure 4.3 Multiple Vertical Termination
10
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
M
N
P
R
Q
(See Note 2)
V
T
S
S
Electrical
Service
V
V
D*
V
X
= VENT TERMINAL
= AIR SUPPLY INLET
= AREA WHERE TERMINAL IS NOT PERMITTED
V
K
= 3 ft. (U.S.A.)
A
B
= 12 inches...............clearances above grade, veranda,
(See Note 1)
6 ft. (Canada)...........clearance to a mechanical
(powered) air supply inlet
(See Note 1)
porch, deck or balcony
= 12 inches...............clearances to window or door
that may be opened, or to perma-
L** = 7 ft...........................clearance above paved
sidewalk or a paved driveway
nently closed window. (Glass)
located on public property
D*
= 18 inches...............vertical clearance to unventilated
soffit or to ventilated soffit located
above the terminal
M*** = 18 inches.................clearance under veranda, porch,
deck, balcony or overhang
42 inches ................vinyl
*30 inches..............for vinyl clad soffits and below
S = 6 inches ...................clearance from sides of elec-
electrical service
(See Note 5)
trical service
F
=
9 inches................clearance to outside corner
T
= 12 inches ..................clearance above electrical
(See Note 5)
G
H
= 6 inches.................clearance to inside corner
service
= 3 ft. (Canada)........not to be installed above a gas
meter/regulator assembly within 3
Alcove Applications
feet (90cm) horizontally from the
center-line of the regulator
N
= 6 inches ..................non-vinyl sidewalls
12 inches ................vinyl sidewalls
P
= 8 ft.
I
= 3 ft. .......................clearance to gas service regulator
vent outlet
QMIN
RMAX
J
= 9 inches (U.S.A.)
1 cap
3 feet
6 feet
9 feet
2 x Q ACTUAL
1 x Q ACTUAL
2/3 x Q ACTUAL
1/2 x Q ACTUAL
12 inches (Canada) clearance to non-mechanical
air supply inlet to building or the
combustion air inlet to any other
appliance
2 caps
3 caps
4 caps
12 feet
QMIN = # termination caps x 3
RMAX = (2 / # termination caps) x QACTUAL
** a vent shall not terminate directly above a sidewalk or paved driveway
which is located between two single family dwellings and serves both
dwellings.
Note 3: Local codes or regulations may require different
clearances.
Note 4: Termination caps may be hot. Consider their proximity to
doors or other traffic areas.
*** only permitted if veranda, porch, deck or balcony is fully open on a
minimum of 2 sides beneath the floor, or meets Note 2.
Note 5: Location of the vent termination must not interfere with
Note 1: On private property where termination is less than 7 feet above a
sidewalk, driveway, deck, porch, veranda or balcony, use of a listed cap
shield is suggested. (See vents components page)
access to the electrical service.
WARNING: In the U.S: Vent system termination is NOT permitted in
screened porches. You must follow side wall, overhang and ground
clearances as stated in the instructions.
Note 2: Termination in an alcove space (spaces open only on one side
and with an overhang) are permitted with the dimensions specified for
vinyl or non-vinyl siding and soffits. 1. There must be 3 feet minimum
between termination caps. 2. All mechanical air intakes within 10 feet
of a termination cap must be a minimum of 3 feet below the termination
cap. 3. All gravity air intakes within 3 feet of a termination cap must be a
minimum of 1 foot below the termination cap.
In Canada: Vent system termination is NOT permitted in screened
porches. Vent system termination is permitted in porch areas with
two or more sides open. You must follow all side walls, overhang
and ground clearances as stated in the instructions.
Hearth & Home Technologies assumes no responsibility for the
improper performance of the appliance when the venting system
does not meet these requirements.
Figure 4.4 Minimum Clearances for Termination
CAUTION: IF EXTERIOR WALLS ARE FINISHED WITH VINYL SIDING, IT IS SUGGESTED THAT A VINYL PROTECTOR KIT BE INSTALLED.
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Vent Information and Diagrams
5
A. Vent Table Key
The abbreviations listed in this vent table key are used in
the vent diagrams.
Symbol
Description
Vertica l
First section (closest to appliance of vertical length
V1
Second section of vertical length
V2
H1
H2
First section (closest to appliance) of horizontal length
Second section of horizontal length
8-1/2 in.
Horizontal
WARNING
Figure 5.1
Fire Hazard.
Explosion Risk.
Asphyxiation Risk.
C. Measuring Standards
Do NOT connect this gas appliance to a
chimney flue serving a separate solid-fuel or
gas burning appliance.
Vertical and horizontal measurements listed in the vent
diagrams were made using the following standards.
1. Pipe measurements are shown using the effective length
of pipe (see Figure 5.2).
•
•
Vent this appliance directly outside.
Use separate vent system for this appliance.
2. Measurements are made from the appliance outer wrap,
not from the standoffs.
May impair safe operation of this appliance or
other appliances connected to the flue.
3. Horizontal terminations are measured to the outside
mounting surface (flange of termination cap) (see Figure
4.1).
B. Use of Elbows
4. Vertical terminations are measured to bottom of termina-
tion cap.
CAUTION
5. Horizontal pipe installed level with no rise.
ALL vent configuration specifications MUST be followed.
•
This product is tested and listed to these
specifications.
•
Appliance performance will suffer if specifications are
not followed.
Length/
Pipe
Inches
DVP4
DVP6
4
6
Diagonal runs have both vertical and horizontal vent as-
pects when calculating the effects. Use the rise for the
vertical aspect and the run for the horizontal aspect (see
Figure 5.1).
DVP12
DVP24
DVP36
DVP48
DVP6A
DVP12A
12
24
36
48
3 to 6
3 to 12
Effective
Height/Length
Two 450 elbows may be used in place of one 900 elbow. On
450 runs, one foot of diagonal is equal to 8.5 inches hori-
zontal run and 8.5 inches vertical run. A length of straight
pipe is allowed between two 450 elbows (see Figure 5.1).
DVP12MI 3 to 12
DVP24MI 3 to 24
Figure 5.2 DVP Pipe Effective Length
12
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
D. Vent Diagrams
WARNING
Fire Risk. Explosion Risk.
Do NOT pack insulation or other combustibles between ceiling firestops.
•
•
ALWAYS maintain specified clearances around venting and firestop systems.
Install wall shield and ceiling firestops as specified.
Failure to keep insulation or other material away from vent pipe may cause fire.
1. Top Vent - Horizontal Termination
V1 Minimum
H1 Maximum
One Elbow
3 ft.
4 ft.
0.9 m
2 ft.
4 ft.
0.6 m
1.2 m
1.8 m
6.1 m
1.2 m
1.5 m
3.7m
5 ft.
6 ft.
12 ft.
20 ft.
V1 + H1 = 40 ft. (12.2 m) Maximum
H1 = 20 ft. (6.1 m) Maximum
Note: When installing the TAOS surround
and venting with one elbow, a straight sec-
tion of venting (30 in. minimum) MUST be
attached directly to starting collars on unit.
Note: The first elbow used MUST always
be DVP90ST.
Figure 5.3
V1 Minimum
H1 + H2 Maximum
Two Elbows
3 ft.
4 ft.
0.9 m
2 ft.
4 ft.
0.6 m
1.2 m
1.8 m
6.1 m
1.2 m
1.5 m
3.7 m
5 ft.
6 ft.
12 ft.
20 ft.
V1 + H1 + H2 = 40 ft. (12.2 m) Maximum
H1 + H2 = 20 ft. (6.1 m) Maximum
Note: V MUST be a minimum
of 3 feet1unless using the TAOS
surround. For TAOS surround, V1
minimum MUST be 30 in.
Note: The first elbow used
MUST always be DVP90ST.
Figure 5.4
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
13
1. Top Vent - Horizontal Termination - (continued)
Three Elbows
V1 + V2 Minimum
H1 + H2 Maximum
3 ft.
4 ft.
0.9 m
1.2 m
1.5 m
3.7 m
2 ft.
4 ft.
0.6 m
1.2 m
1.8 m
6.1 m
5 ft.
6 ft.
12 ft.
20 ft.
V1 + V2 + H1 + H2 = 40 ft. (12.2 m) Maximum
H1 + H2 = 20 ft. (6.1 m) Maximum
Note: V MUST be a minimum
of 3 feet1unless using the TAOS
surround. For TAOS surround, V1
minimum MUST be 30 in.
Note: The first elbow used
MUST always be DVP90ST.
Figure 5.5
14
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Top Vent - Vertical Termination
No Elbow
V1 = 46 ft. Max. (14.0 m)
8 F T.
(2.4mm)
FLUE
OUTLET
Note: A 45° elbow may be attached
directly to starting collars on unit only
if used in conjunction with a return 45°
elbow AND terminating vertical with V =
8 feet MINIMUM.
A straight section of pipe can be used
between the two 45° elbows.
Figure 5.6
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
15
V1 Minimum
H1 Maximum
V2
*
Two Elbows
3 ft.
4 ft.
0.9 m
1.2 m
1.5 m
3.7 m
2 ft.
4 ft.
0.6 m
1.2 m
1.8 m
6.1 m
*
5 ft.
6 ft.
*
12 ft.
20 ft.
*
V1 + V2 + H1 = 40 ft (12.2 m) Maximum
*No specific restrictions on this value EXCEPT
V1 + V2 + H1 cannot exceed 40 ft (12.2 m)
Note: V MUST be a minimum
of 3 feet1unless using the TAOS
surround. For TAOS surround, V1
minimum MUST be 30 in.
Note: The first elbow used
MUST always be DVP90ST.
Figure 5.7
16
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Top Vent - Vertical Termination - (continued)
Three Elbows
V1
H1 + H2
V2
*
3 ft.
4 ft.
5 ft.
12 ft
0.9 m
1.2 m
1.5 m
3.7 m
2 ft.
0.6 m
1.2 m
1.8 m
6.1 m
4 ft.
6 ft.
*
*
20 ft.
*
H1 + H2 = 20 ft (6.1 m) Maximum
*No specific restrictions on this value EXCEPT
V1 + V2 + H1 + H2 = 40 ft (12.2 m) Maximum
Note: V MUST be a minimum
of 3 feet1unless using the TAOS
surround. For TAOS surround, V1
minimum MUST be 30 in.
Note: The first elbow used
MUST always be DVP90ST.
INSTALLED
HORIZONTALLY
Figure 5.8
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Vent Clearances and Framing
6
A. Pipe Clearances to Combustibles
B. Wall Penetration Framing
WARNING
10 in.
Fire Risk.
Explosion Risk.
Maintain vent clearance to combustibles as
specified.
12 in.
•
Do not pack air space with insulation or
other materials.
Failure to keep insulation or other materials
away from vent pipe may cause fire.
B
3 in. TOP
CLEARANCE
A
1 in. CLEARANCE
AROUND VERTICAL
SECTIONS
1 in. SIDE AND
BOTTOM CLEARANCE
A*
B
87-3/4 in.
86-3/4 in.
Figure 6.1 Pipe Clearances
* Shows center of vent framing hole for top venting. The
center of the hole is one (1) inch (25.4mm) above the
center of the horizontal vent pipe.
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm).
The heat shield is designed to be used on a wall 4 in. to 7-1/4 in. (102
mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm) the
existing heat shields must be field trimmed. If wall thickness is greater than
7-1/4 in. (184 mm) a DVP-HSM-B will be required.
Figure 6.3 Exterior Wall Hole
Combustible Wall Penetration
Frame a hole in a combustible wall for an interior wall
shield firestop, (Figure 6.2) whenever a wall is penetrated.
Use same size framing materials as those used in the wall
construction. The wall shield firestop maintains minimum
clearances and prevents cold air infiltration.
3 in . TOP
CLEAR ANCE
HEAT
S HIELD
HEAT
S HIELD
Non-Combustible Wall Penetration
If the hole being penetrated is surrounded by noncombus-
tible materials such as concrete, a hole with diameter one
inch greater than the pipe is acceptable.
1 in . CLEAR ANCE
WALL
S HIELD
FIRES TOP
WALL
BOTTOM& S IDES
Whenever a non-combustible wall is penetrated, the wall
shield firestop is only required on one side and no heat
shield is necessary.
If your local inspector requires the wall shield firestop on
both sides, then both wall shield firestops must have a heat
shield attached to them.
Figure 6.2 Horizontal Venting Clearances to Combustible Materials
18
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
C. Vertical Penetration Framing
WARNING
Fire Hazard
Keep loose materials or blown
insulation from touching the
vent pipe.
•
•
National building codes recommend us-
ing attic shield to keep loose materials/
blown insulation from contacting vent.
ATTIC ABOVE
Hearth & Home Technologies requires
the use of an attic shield.
10 IN. (254 MM)
Installing the Ceiling Firestop
•
Frame an opening 10 inches by 10
inches whenever the vent system
penetrates a ceiling/floor (see Figure
6.4).
•
•
Frame the area with the same sized
lumber as used in ceiling/floor joist.
10 IN.
(254 MM)
When installing a top vent vertical ter-
mination appliance the hole should be
directly above the appliance, unless the
flue is offset.
HOLE SHOULD MEASURE
10 IN. X 10 IN.
(254 MM X 254 MM)
INSIDE TO INSIDE
•
Do not pack insulation around the vent.
Insulation must be kept away from the
pipe.
Installing Attic Shield
Note: An additional ceiling firestop is not
required if attic shield is used.
•
•
Frame opening for attic shield.
Attic shield may be installed above or
below ceiling (see Figure 6.5).
Figure 6.4
•
•
Secure with three fasteners on each
side.
BEND TABS IN
AROUND PIPE
Fold tabs at top of attic shield in toward
vent pipe. Tabs must keep vent pipe
centered within shield.
3 FASTENERS
PER SIDE
•
Field construct additional shield height if
insulation is deeper than height of attic
shield.
ATTIC SHIELD INSTALLED
ABOVE CEILING
ATTIC SHIELD INSTALLED
BELOW CEILING
Figure 6.5
Installing the Attic Shield
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Appliance Preparation
7
A. Securing and Leveling the Appliance
WARNING
Fire Risk.
• Prevent contact with sagging, loose
insulation.
• Do NOT install against combustible
materials such as exposed insulation,
plastic and insulation backer.
CAUTION
Sharp Edges
•
Wear protective gloves
and safety glasses dur-
ing installation.
The diagram shows how to properly position, level, and
secure the appliance (see Figure 7.1). Nailing tabs are pro-
vided to secure the appliance to the framing members.
NAILING TABS
(BOTH S IDES )
• Place the appliance into position.
• Level the appliance from side to side and front to
back.
Figure 7.1 Proper Positioning, Leveling and Securing
of an Appliance
• Shim the appliance as necessary. It is acceptable to use
wood shims.
WARNING
• Bend out nailing tabs on each side.
Fire Risk.
• ALWAYS maintain specified
• Keep nailing tabs flush with the framing.
clearances around the appliance.
• Secure the appliance to the framing by using nails or
screws through the nailing tabs. Holes are provided in the
basepan (inside the hearth) for securing to the floor.
• Do NOT notch into the framing around the appliance spacers.
Failure to keep insulation, framing or other material away
from the appliance may cause fire.
20
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Vent Pipe
8
Assembling Pipe Sections
A. Assembly of Vent Sections (DVP Pipe)
Insert the inner flue of section A into the flared inner flue of
section B.
WARNING
Start the outer flue of sectionAover the outer flue of section
B (see Figure 8.2). Note: The end of the pipe sections with
the lances/tabs on it will face towards the appliance. Once
both inner and outer flues are started, press sectionAonto
section B firmly until all lances have snapped into place.
Check to make sure they have snapped together (see Fig-
ure 8.3) and the seams are not aligned (see Figure 8.4).
Tug slightly on sectionAto confirm it has completely locked
into place. It is acceptable to use screws no longer than
1 inch to hold outer pipe sections together. If predrilling
holes, do NOT penetrate inner pipe.
Do not mix pipe, fittings or joining
methods from different manufacturers.
WARNING
Fire Risk
Exhaust Fumes Risk
Impaired Performance of Appliance
• Overlap pipe slip sections at least 1-1/2
inches.
• Use pilot holes for screws.
For 90° and 45° elbows that are changing the vent direction
from horizontal to vertical, one screw minimum should be
put in the outer flue at the horizontal elbow joint to prevent
the elbow from rotating. Use screws no longer than 1 inch.
If predrilling screw holes, do NOT penetrate inner pipe.
• Screws must not exceed one inch long.
• Pipe may separate if not properly joined.
Attaching Vent to the Firebox Assembly
To attach the first pipe section to the collars, slide the male
end of the inner vent of the pipe section over the inner collar
on the firebox assembly. At the same time, slide the outer
flue over the outer collar on the appliance. Push the pipe
section into the appliance collar until all the lances (see
Figure 8.1) have snapped in place. Tug slightly on the sec-
tion to confirm it has completely locked into place.
High Temperature Silicone Sealant
Commercial, Multi-family (multi-level exceeding two
stories), or High-rise Applications only
Commercial, Multi-family (Multi-level exceeding two
stories), & High-Rise Applications
For Installation into Commercial, multi-family (multi-level ex-
ceeding two stories) or high-rise applications: All pipe joints
must be sealed with high temperature silicone, including the
slip section that connects directly to the horizontal termina-
tion cap.
• Apply a bead of silicone sealant inside the female outer
pipe joint prior to joining sections. See Figure 8.1
Figure 8.1 Lances
• Only outer pipes are sealed. Do not seal the inner flue.
All unit collar, pipe, slip section, elbow and cap outer flues
shall be sealed in this manner, unless otherwise stated.
A
B
Note: The end of the pipe sections with the lances/tabs on it
will face toward the appliance.
WARNING
Fire Risk
Explosion Risk
If slip section seals are broken during the
removal of the termination cap, gas will leak and
a fire or explosion may occur.
Figure 8.2
Figure 8.3
Do not break silicone seals on slip sections.
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
21
This will secure the slip section to the desired length and
prevent it from separating. The slip section can then be
attached to the next pipe section.
Note: Make sure that the seams are not aligned to prevent
unintentional disconnection.
If the slip section is too long, the inner and outer flues of
the slip section can be cut to the desired length.
Cut from this end
(outer)
CORRECT
Cut from this end
(inner)
INCORRECT
Figure 8.5
Figure 8.4 Seams
Assembling Minimum Installations (MI) Sections
MI sections are non-unitized so that they can be cut to a
certain length. Cut these sections to length from the non-
expanded end (see Figure 8.5).
They can then be attached by first connecting the expanded
end of the MI inner flue with the inner pipe from the adjacent
pipe section and securing with three screws. The expanded
portion of the MI inner flue must overlap completely with
the unexpanded end of the adjacent pipe section.
The outer flue can then be inserted into the adjacent outer
flue expanded end and attached to the next pipe section
with three screws. The other end of the MI pipe section can
then be attached by fitting another pipe section to it and
snapping it together, as normal.
Figure 8.6 Slip Section Pilot Holes
Note: When installing a vent system with an HRC termination
cap, all pipe system joints shall be sealed using a high-
temperature silicone sealant.
• Apply a bead of silicone sealant inside the female outer
pipe joint prior to joining sections.
• Only outer pipes are sealed, sealing the inner flue is not
required. All unit collar, pipe, slip section, elbow and cap
outer flues shall be sealed in this manner.
Assembling DVP-12A Slip Sections
The outer flue of the slip section should slide over the outer
flue of the pipe section and into (inner flue) the last pipe
section (see Figure 8.6) .
Slide together to the desired length, making sure that a
1-1/2 inch outer flue overlap is maintained between the
pipe section and slip section.
The pipe and slip section need to be secured by driving
two screws through the overlapping portions of the outer
flues using the pilot holes (see Figure 8.7).
Figure 8.7 Screws into Slip Section
22
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
Securing the Vent Sections
Vertical Sections
Vertical sections of pipe must be supported every 8 feet
after the 25 foot maximum unsupported rise. The vent sup-
port or plumber’s strap (spaced 120° apart) may be used
to do this (see Figure 8.8).
Horizontal Sections
Horizontal sections of vent must be supported every 5 feet
with a vent support or plumber’s strap.
Figure 8.8 Securing Vertical Pipe Sections
Figure 8.9 Securing Horizontal Pipe Sections
B. Disassembly of Vent Sections
To disassemble any two pieces of pipe, rotate either section
(see Figure 8.10), so that the seams on both pipe sections
are aligned (see Figure 8.11). They can then be carefully
pulled apart.
WARNING
Fire Risk.
Explosion Risk.
Combustion Fume Risk.
Use vent run supports per installation
instructions.
Connect vent sections per installation
instructions.
Figure 8.10 Rotate Seams for Disassembly
•
•
Maintain all clearances to combustibles.
Do NOT allow vent to sag below
connection point to appliance.
Improper support may allow vent to sag or separate.
Figure 8.11 Align and Disassemble Vent Sections
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
23
C. Installing Heat Shield and Horizontal Termination Cap
Installing the Horizontal Termination Cap
WARNING
Vent termination must not be recessed in the wall. Siding
may be brought to the edge of the cap base.
Fire Hazard
Impaired performance of appliance
Flash and seal as appropriate for siding material at outside
edges of cap.
• Telescoping flue section of termination cap
MUST be used when connecting pipe section
to termination cap.
When installing a horizontal termination cap, follow the cap
location guidelines as prescribed by current ANSI Z223.1
and CAN/CGA-B149 installation codes.
• Maintain a 1-1/2 inch minimum overlap on
telescoping flue section of termination cap.
WARNING
WARNING
Burn Risk
• Local codes may require installation of a cap
shield to prevent anything or anyone from
touching the hot cap.
Fire Risk
Exhaust Fumes Risk
Impaired Performance of Appliance
• Overlap pipe slip sections at least 1-1/2 inches.
• Use pilot holes for screws.
• Screws must not exceed 1 inch long.
• Pipe may separate if not properly joined.
REAR VENT
HEAT SHIELD
HEAT SHIELD OR
EXTENDED
1-1/2 IN. (38 MM) MIN.
OVERLAP
HEAT SHIELD
Heat Shield Requirements for Horizontal Termination
WALL SHIELD FIRESTOP
For all horizontally vented appliances, a heat shield MUST
be placed one inch above the top of the vent between the
wall shield firestop and the base of the termination cap.
There are two sections of the heat shield. One section
is factory-attached to the wall shield firestop. The other
section is factory-attached to the cap. See Figure 8.12.
INNER VENT
INTERIOR
EXTERIOR
SHEATHING
If the wall thickness does not allow the required 1-1/2 inch
(38 mm) heat shield overlap when installed, an extended
heat shield (DVP-HSM-B) must be used.
OUTER VENT
HEAT SHIELD EXTENSION NOT SHOWN.
Important Notice: Heat shields may not be field constructed.
Figure 8.12 Venting through the Wall
The extended heat shield (DVP-HSM-B) may need to
be cut to length. You will attach the cut heat shield to
the existing cap heat shield or wall shield firestop heat
shield (refer to Figure 8.12) using the supplied screws.
You MUST maintain a 1-1/2 in. (38 mm) overlap of the
extended heat shield and the existing shields (both ends
of the heat shield). The small leg on the extended heat
shield should rest on the top of the vent (pipe section) to
properly space it from the pipe section.
Note: Where required, an exterior wall flashing is available.
When penetrating a brick wall, a brick extension kit is available
for framing the brick.
24
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
Caulk the gap between the roof flashing and the outside
diameter of the pipe. Also caulk the perimeter of flashing
that contacts roof surface as shown in Figure 8.15.
D. Installing Roof Flashing and Vertical Ter-
mination Cap
To install roof flashing see Figure 8.13.
To attach the vertical termination cap, slide the inner col-
lar of the cap into the inner flue of the pipe section and
place the outer collar of the cap over the outer flue of the
pipe section.
For installation of vertical termination cap see minimum
vent heights for various pitched roofs (see Figure 8.15).
HORIZONTAL
OVERHANG
Secure with three screws into the outer flue. Secure the cap
by driving the three self-tapping screws (supplied) through
the pilot holes in the outer collar of the cap into the outer
flue of the pipe (see Figure 8.14).
2 FT.
20 INCHES MIN.
VERTICAL
MIN.
WALL
LOWEST
DISCHARGE
OPENING
TERMINATION CAP
GAS DIRECT VENT
TERMINATION CAP
X
12
ROOF PITCH
IS X/ 12
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
(1 of 3)
STORM
COLLAR
Roof Pitch
H (Min.) Ft.
Flat to 6/12.......................................1.0*
Over 6/12 to 7/12...........................1.25*
Over 7/12 to 8/12.............................1.5*
Over 8/12 to 9/12.............................2.0*
Over 9/12 to 10/12............................ 2.5
Over 10/12 to 11/12........................ 3.25
Over 11/12 to 12/12.......................... 4.0
Over 12/12 to 14/12.......................... 5.0
Over 14/12 to 16/12.......................... 6.0
Over 16/12 to 18/12.......................... 7.0
Over 18/12 to 20/12.......................... 7.5
Over 20/12 to 21/12.......................... 8.0
SCREWS
CAULK
Figure 8.14
* 3 foot minimum in snow regions
Figure 8.13 Minimum Height from Roof to Lowest
Discharge Opening
CAULK
WARNING
Fire Risk.
Explosion Risk.
Inspect external vent cap regularly.
•
•
Ensure no debris blocks cap.
Combustible materials blocking cap may
ignite.
•
Restricted air flow affects burner operation.
Figure 8.15
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Assembling and Installing Storm Collar
CAUTION
Sharp Edges
•
Wear protective gloves
and safety glasses dur-
ing installation.
Connect both halves of the storm collar with two screws
(see Figure 8.16).
Wrap the storm collar around the exposed pipe section
and align brackets. Insert a bolt (provided) through the
brackets and tighten nut to complete storm collar assembly
(see Figure 8.17).
Figure 8.17 Assembling the Storm Collar Around the Pipe
Slide the assembled storm collar down the pipe section
until it rests on the roof flashing.
Caulk around the top of the storm collar (see Figure
8.14).
Figure 8.16 Assembling the Storm Collar
26
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
Gas Information
9
A. Fuel Conversions
C. Gas Connection
Before making gas connections ensure that appliance be-
ing installed is compatible with the available gas type.
Note: Have the gas supply line installed in accordance
with local building codes, if any. If not, follow ANSI
223.1. Installation should be done by a qualified installer
approved and/or licensed as required by the locality. (In
the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas fitter).
Any natural or propane gas conversions necessary to
meet the appliance and locality needs must be made by
a qualified technician using Hearth & Home Technologies
specified and approved parts.
B. Gas Pressures
Note: A listed (and Commonwealth of Massachusetts ap-
proved) 1/2 inch (13 mm) T-handle manual shut-off valve and
flexible gas connector are connected to the 1/2 inch (13 mm)
control valve inlet.
Proper input pressures are required for optimum appli-
ance performance. Gas line sizing requirements need to
be made following NFPA51.
•
If substituting for these components, please consult
local codes for compliance.
WARNING
Refer to Reference Section 16 for location of gas line
Fire Risk.
access in appliance.
Explosion Hazard.
High pressure will damage valve.
Note: Gas line may be run from either side of the appliance
provided the hole in the outer wrap does NOT exceed 2-1/2
inches in diameter and does not penetrate the firebox.
• Disconnect gas supply piping BEFORE
pressure testing gas line at test pressures
above 1/2 psig.
• Close the manual shutoff valve BEFORE
pressure testing gas line at test pressures
equal to or less than 1/2 psig.
WARNING
Gas Leak Risk
• Support control when attaching pipe to
prevent bending gas line.
WARNING
Verify inlet pressures.
• High pressure may cause overfire condition.
• Low pressure may cause explosion.
Note: The gap between supply piping and gas access hole
may be caulked with high temperature caulk or stuffed with
non-combustible, unfaced insulation to prevent cold air
infiltration.
• Verify minimum pressures when other
household gas appliances are operating.
Install regulator upstream of valve if line
pressure is greater than 1/2 psig.
Pressure requirements for appliance are shown in the
table below. Minimum pressures must be met when other
household gas appliances are operating.
Pressure
Natural Gas
Propane
5.0 inches
w.c.
11.0 inches
w.c.
Minimum inlet pressure
14.0 inches
w.c.
14.0 inches
w.c.
Maximum inlet gas pressure
Manifold pressure
3.5 inches
w.c.
10.0 inches
w.c.
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
27
• Ensure that gas line does not come in contact with outer
wrap of appliance. Follow local codes.
HIGH ALTITUDE INSTALLATIONS
U.L. Listed gas appliances are tested and approved without
requiring changes for elevations from 0 to 2000 feet in the
U.S.A. and Canada.
• Incoming gas line should be piped into the valve
compartment and connected to the 1/2 inch connection
on the manual shutoff valve.
When installing this appliance at an elevation above 2000 feet,
it may be necessary to decrease the input rating by changing
the existing burner orifice to a smaller size. Input rate should
be reduced by 4% for each 1000 feet above a 2000 foot
elevation in the U.S.A., or 10% for elevations between 2000
and 4500 feet in Canada. If the heating value of the gas has
been reduced, these rules do not apply. To identify the proper
orifice size, check with the local gas utility.
WARNING
Fire or Explosion Hazard
• Gas buildup during line purge may ignite.
• Purge should be performed by qualified technician.
• Ensure adequate ventilation.
If installing this appliance at an elevation above 4500 feet (in
Canada), check with local authorities.
• Ensure there are no ignition sources such as
sparks or open flames.
• A small amount of air will be in the gas supply lines.
When first lighting appliance it will take a short time for
air to purge from lines. When purging is complete the
appliance will light and operate normally.
WARNING
CHECK FOR GAS LEAKS
Explosion Risk
Fire Risk
Asphyxiation Risk
• Check all fittings and connections.
• Do not use open flame.
• After the gas line installation is complete, all
connections must be tightened and checked
for leaks with a commercially-available,
non-corrosive leak check solution. Be sure
to rinse off all leak check solution following
testing.
Fittings and connections may have loosened
during shipping and handling.
WARNING
Fire hazard.
Do NOT change the valve settings.
• This valve has been preset at the factory.
• Changing valve settings may result in fire
hazard or bodily injury.
28
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Information
10
C. Intellifire Ignition System Wiring
A. Recommendation for Wire
This appliance requires a 110 VAC supply to the appliance
junction box for operation. A wiring diagram is shown in
Figure 10.1.
This appliance requires 110-120 VAC be wired to the junc-
tion box for proper operation of the appliance (Intellifire
ignition).
This appliance is equipped with an Intellifire control valve
which operates on a 3 volt system.
Note: This appliance must be electrically wired and grounded
in accordance with local codes or, in the absence of local
codes, with National Electric Code ANSI/NFPA 70-latest
edition or the Canadian Electric Code, CSA C221.1.
This appliance is supplied with a battery pack and a 3 volt
AC transformer, which requires the installation of the sup-
plied junction box. It is highly recommended that the junc-
tion box be installed at this time to avoid reconstruction.
The battery pack requires two D cell batteries (not in-
cluded).
B. Connecting to the Appliance
NOTE: Batteries cannot be placed in the battery pack
while using the 3 voltAC transformer. The transformer
must be unplugged if the battery pack is used or battery
life will be reduced.
WARNING
Wire 110V to electrical junction box.
Do NOT wire 110V to valve.
Do NOT wire 110V to wall switch.
•
•
Incorrect wiring will damage millivolt valves.
Incorrect wiring will override IPI safety lock-
out and may cause explosion.
Wiring to the battery pack is left disconnected in order
to conserve battery life. In the case of a loss of power,
simply connect red and black wire leads to activate bat-
tery power (connect red to red, black to black). The fire-
place can be used as necessary. Once power (110 VAC)
is restored, disconnect red and black wire leads to extend
battery life.
•
•
•
This appliance may be used with a wall switch, wall
mounted thermostat and/or a remote control.
If using thermostat use one compatible with a millivolt
gas valve system.
CAUTION
Battery polarity must be correct or module damage will
Follow parameters for locating thermostat (see individ-
ual thermostat instructions) to ensure proper operation
of appliance.
occur.
•
•
•
Use low resistance thermostat wire for wiring from igni-
tion system to the wall switch and thermostat.
Optional Accessories Requirements
Wiring for optional accessories should be done now to
avoid reconstruction.
Keep wire lengths short as possible by removing any
excess wire length.
Low voltage and 110 VAC voltage cannot be shared
within the same wall box.
D. Wall Switch (Required)
A wall switch must be installed of this fireplace. This will
allow the unit to operate if the power goes out (battery
operation).
Position the wall switch in the desired position on the
wall. An assembly of 18 ft of 20 AWG is provided with
the appliance to connect the wall switch to the appliance.
Instead of the supplied assembly, wire with a length of
25 ft or less and a gauge of 20 AWG through 14 AWG is
acceptable. The wire needs a jacket with a temperature
rating of 140oF (60oC) or higher. At the appliance connect
the wire to the ON/OFF switch pigtails.
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
29
INTERMITTENT PILOT IGNITOR
PLUG-IN
3V TRANSFORMER
IGNITION MODULE 3 VAC
ON/OFF
WALL SWITCH
FLAME SPARKER/
SENSOR
IGNITION
MODULE
(3V)
LOW VOLTAGE
SEE NOTE 1.
VALVE
LOW VOLTAGE
SEE NOTE 1
WHT
ORG
GROUND
REMOTE
CONTROL
NEUTRAL
HOT
GROUND TO
FIREPLACE
CHASSIS
BLK
RED
WHITE WIRE CAN BE
PLUGGED INTO ANY OF
#1 - #5 LOCATIONS
ON THE NEUTRAL SIDE
VALVE
BLACK WIRE CAN BE
PLUGGED INTO ANY OF
#1 - #5 LOCATIONS
ON THE HOT SIDE
TRANSFORMER
3 VAC
THERMOSTAT
WIRE ASSEMBLY
2045-045
PLUG IN
REMOTE JUMPER
WIRE
NOTE 1: IGNITION MODULE, VALVE, PILOT AND WALL SWITCH OPERATE ON 3 VOLTS.
120 VAC IS REQUIRED AT JUNCTION BOX UNLESS EQUIPPED WITH BATTERY BACK-UP.
Figure 10.1 Intellifire Pilot Ignition (IPI) Wiring Diagram
CAUTION
Label all wires prior to disconnection when servicing controls.
Wiring errors can cause improper and dangerous operation.
Verify proper operation after servicing.
WARNING
Shock hazard.
•
Replace damaged wire with type 105O C
rated wire.
•
Wire must have high temperature insulation.
30
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
E. Junction Box Installation
Romex
Connector
If the box is being wired from the OUTSIDE of
the appliance:
14/2WG
•
•
•
•
Remove the cover plate located on the outer
shell - right side (see Figure 10.3).
Cover Plate
outside firebox
Install the supplied Romex™ connector in the
cover plate.
Feed the necessary length of wire through the
connector.
Make all necessary wire connections and reat-
tach the cover plate to the outer shell.
Copper
ground attached
to GRN screw with
GRN wire
GRN wire
inside box
If the box is being wired from the INSIDE of the
appliance:
Note: Do NOT wire
110VAC to wall switch.
•
Remove the screw attaching the junction
box/receptacle to the outer shell, rotate the
junction box inward to disengage it from the
outer shell (see Figure 10.3).
Figure 10.3 Junction Box Detail
•
•
Feed the necessary length of wire through the connector.
•
Pull the electrical wires from outside the ap-
pliance through this opening into the valve
compartment.
Make all necessary wire connections to the junction box/re-
ceptacle and assemble the junction box/receptacle to the outer
shell.
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
31
Finishing
11
A. Mantel Projections
Figure 11.1 shows the minimum vertical and corresponding
maximum horizontal dimensions of appliance mantels or
other combustible projections above the top front edge of
the appliance.
1/2 INCH NON-COMBUSTIBLE
BOARD REQUIRED ON UNIT FACE
Note: All
measurements
in inches.
31
1 INCH
CEILING
MINIMUM
TO
VENT PIP E
18
17
16
15
14
NAILING
TABS
9 1/8
MIN.
13
12
11
FINISHING
EDGE
10
3 1/8
9
TRIM
8
7
3 7/8
6
5
COMBUSTIBLE MATERIALS
MAY CONTACT AND COVER
FRONT AND SIDE AREAS
BELOW GLASS/FRONT
TOP OF
FINISHING STRIP
TOP OF
UNIT
Figure 11.3 Noncombustible Facing Diagram
Figure 11.1 Clearances to Mantels or other Combustibles
above Appliance
WARNING
Risk of Fire
•
Non-combustible clearances MUST be
maintained.
•
Sheetrock, wood or other combustibles must
NOT be used as sheathing or facing in the
non-combustible zone.
•
•
See Section 11 for proper clearances.
See Section 1 for combustible/non-
combustible definitions.
Figure 11.2
Mantel Leg or Wall Projections
(Acceptable on both sides of opening.)
WARNING
B. Facing Material
Fire Risk.
Finish all edges and fronts to clearances and
specifications listed in manual.
WARNING
•
•
•
•
Black metal appliance front may be covered with
noncombustible material only.
Fire Risk.
Do NOT obstruct air inlet or outlet grilles.
Do NOT modify grilles.
Do NOT overlap combustible materials onto appliance
front.
•
Modifying or covering grilles could cause
temperature rise and fire hazard.
Finishing materials must not interfere with:
Install combustible materials only up to specified clear-
ances on top, front and side.
•
•
•
Air flow through grilles or louvers.
Operation of louvers or doors.
Access for service.
Seal joints between the finished wall and appliance top
and sides using only a 300º F minimum sealant.
32
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Drywall or other finishing materials may be finished all
the way up to the finishing edge trim or unit front face,
but MUST NOT extend inside of finishing edge trim.
C. Finishing Styles
This model has multiple installation and finishing options.
The following section describe three basic installations.
CAUTION
Finishing materials cut inside the provided template will
Note: A 1/2 inch clearance must be maintained between
combustible materials and the front face of the fireplace.
cause the door to not fit.
•
Finishing materials may be fastened or secured to unit
below the glass/front opening.
OPTION A: Flush Wall Finish
Kiva-style finished in a straight wall (see Figure 11.4).
OPTION B: Kiva-style Arch
The second installation option requires the construction
of a kiva-style arch. This option recesses the unit into the
wall such that construction of a hearth is not necessary
(see Figure 11.5).
5 INCH
MAXIMUM
DEPTH
INCLUDING
WALL FINISH
MATERIAL
Figure 11.4 Flush wall installation
•
•
•
Unit is installed using framing dimensions found in
Figure 3.2.
Do not use nailing tabs provided on unit sides for
Option A.
Nailing tabs are attached to the top of the unit. Install
nailing tabs using screws on upper unit sides (see
Figure 11.3).
Figure 11.5
•
This places unit back 1/2 inch from framing studs such
that drywall or other material can be brought directly
across non-combustible board up to finish edge trim.
•
•
Framing depth increases from that shown in Figure
3.2, (Dimension C). Dimension C will vary depending
on the depth of the desired kiva-style arch (see Figure
11.5).
WARNING
Once depth of desired kiva-style arch is determined
(minimum of 3-3/32 inches and maximum 5 inches),
add that to Dimension C from Figure 3.2. Level, set
and secure fireplace using nailing tabs provided on
fireplace sides. Secure with screws or nails into BACK
of framing studs.
Fire Risk.
1/2 inch non-combustible board installed on front
face of fireplace MUST remain if using combustible
finishing materials.
•
A cardboard template is printed on unit shipping
carton and may be used to help cut drywall or other
finishing materials. Simply cut along line and use it as
a template.
•
Kiva-style arch dimensions: Maximum depth
equals 5 inches (includes finish wall surface).
Minimum depth equals 3-3/32 inches.
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
33
OPTION C: SOUTHWESTERN kiva-style
Note: Previous numbers are for combustible
construction numbers. Arch may protrude up to
5-1/2 inches maximum as measured from unit
front face.
The third installation option illustrated is a corner-installa-
tion with custom finishing. This option requires advanced
finishing methods involving either combustible or non-com-
bustible construction materials (see Figure 11.7).
Note: The kiva-style arch depth may be any size if
using noncombustible materials i.e. concrete, steel,
plaster, etc.
•
A template is provided on unit shipping carton.
Simply cut along the line and use as a template when
constructing kiva-style arch (see Figure 11.6).
CAUTION
Template for kiva-style arch represents MINIMUM inside
dimensions. When constructing kiva-style arch, you must
add thickness of finishing materials to achieve proper size
of finished arch.
Figure 11.7
•
A template is provided on the unit shipping carton.
Simply cut along the line and use as a template for
construction purposes.
BACKING
MATERIAL
•
•
The cardboard template provided represents MINIMUM
inside dimensions of the finished wall surface.
If finishing with plaster or drywall, a finish edge trim is
provided around door front on unit. Finishing materials
MUST not extend inside of the finish edge trim.
CAUTION
KIVA-STYLE ARCH
STRUCTURE
Finishing materials cut inside the provided template or inside
finish edge trim will cause the door not to fit.
FINISHING
MATERIAL
WARNING
Figure 11.6
Fire Risk.
•
Inside of the kiva-style arch can be finished using com-
bustible materials. For example, thin drywall may be
layered to form around curved arch.
Follow minimum specified clearances found in
Section 16, (Appliance Dimensions Diagram)
and on fireplace exterior if using combustible
framing materials.
34
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
OPTION D: Flush Wall Finish with Luxor Surround
Kiva-style finished in a straight wall (see Figure 11.8).
3-in. GAP
SHEETROCK
EDGE
FINISHING STRIP
Figure 11.9 Taos Surround on Platform
12-1/8 in.
Figure 11.8 Flush wall installation with Luxor Surround
•
•
•
Unit is installed using framing dimensions found in
Figure 3.2.
Do not use nailing tabs provided on unit sides for
Option D.
27-3/4 in.
Nailing tabs are attached to the top of the unit. Install
nailing tabs using screws on upper unit sides (see
Figure 11.3).
7-3/4 in.
•
This places unit back 1/2 inch from framing studs such
that drywall or other material can be brought directly
across non-combustible board up to finishing strip.
34-3/8 in.
5-3/4 in.
WARNING
Fire Risk.
1/2 Inch non-combustible board installed on front
face of fireplace MUST remain in place if using
combustible finishing materials.
Figure 11.10 Platform Dimensions
•
A cardboard template is printed on unit shipping
carton and may be used to help cut drywall or other
finishing materials. Simply cut along line and use it as
a template. For Luxor Surround, cut an additional 3 in.
wider than the template.
EVEN GAP
Î
OPTION E: Corner Mount with Taos Surround
Unit must be placed on 5 3/4” tall platform. Platform
should not exceed unit footprint. See Figure 11.10 Install
unit in corner as tight as minimum clearances allow. If
necessary, shim unit (up to 1/8”) so that gap between unit
facing and Taos arch is even throughout as shown in Fig-
ure 11.10.
Follow instructions included with Taos Surround for mount-
ing surround to walls.
Figure 11.11 Even Gaps All Around.
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
35
Appliance Setup
12
A. Remove Shipping Materials
Placing the Ember Material
Ember material is shipped with this gas appliance. To place
the ember material:
Remove shipping materials from inside or underneath the
firebox.
• Embers CANNOT be placed directly over ports.
B. Clean the Appliance
• When placing Glowing Embers® onto the burner care
should be taken so that the ports are not covered. Place
the dime-size ember pieces near the ports, but not on the
ports (see Figure 12.1). Failure to follow this procedure
will likely cause lighting and sooting problems.
Clean/vacuum any sawdust that may have accumulated
inside the firebox or underneath in the control cavity.
C. Accessories
Install approved accessories per instructions included with
accessories. See Service Parts List for appropriate acces-
sories. Refer to Section 16.
Place material near ports but do NOT cover
port openings.
WARNING
Shock or fire risk.
Use ONLY optional accessories approved for
this appliance.
•
•
•
Using non-listed accessories voids
warranty.
Using non-listed accessories may result in
a safety hazard.
Only Hearth & Home Technologies
approved accessories may be used safely.
EMBER
MATERIA L
D. Lava Rock and Ember Placement
Figure 12.1 Placement of Embers
WARNING
• Save the remaining ember materials for use during appli-
ance servicing. The embers provided should be enough
for 3 to 5 applications.
Explosion Risk.
•
•
•
Follow ember placement instructions in
manual.
Do NOT place embers directly over
burner ports.
Replace ember material annually.
Improperly placed embers interferes with proper burner
operation.
Placing the Lava Rock
Place the lava rock on the bottom of the firebox. Evenly
spread the lava rocks with your hand.
36
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
E. Positioning the Logs
If the gas logs have been factory installed they should not
need to be positioned. If the logs have been packaged
separately, refer to the following instructions.
Log Assembly: LOGS-BRAVO
CAUTION: Logs are fragile!
Carefully remove the logs
from the packaging.
Before placing logs, check
that the sensor on the pilot
assembly does not contact
the burner.
6
2
5
4
Remove shipping bracket
1
and tie straps from the burn-
3
er and grate.
Place the lava rock on the
bottom of the firebox. Evenly
spread the lava rocks with
your hand.
TAB
TIE STRAPS
SENSOR
GRATE
BURNER
Shipping Bracket
ADJUST LOG SO
SURFACE IS FLUSH
GROOVE FOR
LOG #2
RIGHT LOG
TAB
1
1
LOG #1 (SRV750-703): Place log #1 between log tabs on left side and right side of the burner. Place such that
bottom surface of log rests on burner surface (left).
704-936C
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
37
RIGHT
GRATE
TINE
2
2
LOG #2 (SRV750-705): Place the top of log #2 in the groove on log #1. Place the base of the log
on the inside of the outer right grate tine with the grate tine fitting in the groove on log #2.
GROOVE FOR
LOG #4
3
3
LOG #3 (SRV750-706): Place log #3 with the base on the inner right grate tine. The top of the log
should be placed so that it doesn’t cover any ports on the burner.
GROOVE
FOR
LOG #5
4
LOG
TAB
LOG
TAB
LEFT
GRATE
TINE
2
2
4
GROOVE
LOG #4 (SRV750-704): Place log #4 such that the groove mates with the left grate tine. The up-
per end of the log should mate with the flat spot on log #2.
38
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
GROOVE
FOR
LOG #6
5
5
LOG #5 (SRV704-702): Place log #5 on right side of the grate. Position the base of the log on the
log tab. The log tab should insert into slot feature on back side of log. Place the top of the log into the
groove on log #1.
6
6
LOG #6 (SRV704-701): Place log #6 on left side of grate. Position the base of the log on the log
tab. Log tab should insert into slot feature on back side of log. Place the top of the log into flat spot on
log #1.
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
39
F. Glass Assembly
G. Grilles and Trim
Install optional marble and brass trim surround kits as de-
sired. Marble, brass, brick, tile, or other noncombustible
materials can be used to cover up the gap between the
sheet rock and the appliance.
WARNING
Handle glass doors with care.
•
Inspect the gasket to ensure it is
undamaged.
•
Inspect the glass for cracks, chips or
scratches.
H. Air Shutter Settings
•
•
Do NOT strike, slam or scratch glass.
NG
LP
Do NOT operate appliance with glass door removed,
cracked, broken or scratched.
Burner
1/8 in.
1/2 in.
•
Replace glass door assembly as a complete appliance.
Removing Glass Assembly
•
Unscrew the two top wing bolts and unlatch the two bottom
spring clips (see Figure 12.2).
•
Remove the front trim door and the glass door from the
appliance.
Replacing Glass Assembly
• Replace the glass door and a front trim door on the
appliance. Pull out and latch the spring clips into the
tabs on the glass frame and tighten the top wing bolts.
GLASS
CLIPS
Figure 12.2 Glass Assembly
40
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions
13
A. Before Lighting Appliance
WARNING
This appliance has an Intellifire ignition system.
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
CAUTION
Hot glass will cause burns.
• Do not touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
If installing Intellifire ignition battery backup:
•
Do not install batteries if the backup mode may not be
used for extended time.
•
•
Batteries may leak.
• CAREFULLY SUPERVISE children in same room as
fireplace.
Install batteries only when needed for power outage.
• Alert children and adults to hazards of high temperatures.
High temperatures may ignite clothing or other
flammable materials.
• Keep clothing, furniture, draperies and other flammable
materials away.
Before operating this appliance have a qualified tech-
nician:
•
•
Remove all shipping materials from inside and/or
underneath the firebox.
This appliance has been supplied with an integral barrier
to prevent direct contact with the fixed glass panel. Do
NOT operate the appliance with the barrier removed.
Review proper placement of logs, rockwool, lava
rock, and vermiculite.
•
•
•
•
Check the wiring.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
Check the air shutter adjustment.
Ensure that there are no gas leaks.
Ensure that the glass is sealed and in the proper
position.
•
Ensure that the flow of combustion and ventilation air
is not obstructed (front grilles and vent caps).
WARNING
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage. Refer to
the owner’s information manual provided with this appliance.
For assistance or additional information consult a qualified
installer, service agency or the gas supplier.
Glass door must be in place when
appliance is operating.
Risk of:
• Combustion Fumes
• Fire
WARNING
Do NOT operate appliance with glass
door removed.
Do NOT use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and
any gas control which has been under water.
• Open viewing glass for servicing only.
• Glass door MUST be in place and sealed before operating
appliance.
• Only use glass door certified for use with appliance.
• Glass replacement should be done by qualified technician.
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
41
B. Lighting Appliance
Intellifire Ignition
LIGHTING
INSTRUCTIONS
(IPI)
FOR YOUR SAFETY
READ BEFORE LIGHTING
WARNING: If you do not follow these instructions
exactly, a fire or explosion may result causing property
damage, personal injury or loss of life.
1. Turn off all electric power to the appli-
ance.
2. This appliance is equipped with an igni-
tion device which automatically lights the
burner. Do not try to light the burner by
hand.
•
•
Do not touch any electric switch; do
not use any phone in your building.
A. This appliance is equipped with
an intermittent pilot ignition (IPI)
device which automatically lights
the burner. Do not try to light the
burner by hand.
Immediately call your gas supplier
from a neighbor’s phone. Follow
the gas supplier’s instructions.
GAS
VALVE
•
If you cannot reach your gas sup-
plier, call the fire department.
B. BEFORE LIGHTING, smell all
around the appliance area for
gas. Be sure to smell next to
the floor because some gas is
heavier than air and will settle on
the floor.
C. Do not use this appliance if any part
has been under water. Immediately
call a qualified service technician
to inspect the appliance and to
replace any part of the control
system and any gas control which
Do not try to light any appliance.
has been under water.
3. Wait five (5) minutes to clear out any gas.
Then smell for gas, including near the
floor. If you smell gas, STOP! Follow “B”
in the Safety Information located on the left
side of this label. If you don’t smell gas,
go to next step.
WHAT TO DO IF YOU SMELL GAS
•
4. Turn on all electric power to the appli-
WARNING: CAUTION:
ance.
5. To light the burner, flip the ON/OFF
switch to the “ON” position. (The ON/OFF
switch may include a wall switch if so
equipped).
Hot while in operation. Do not touch.
Keep children, clothing, furniture,
gasoline and other liquids having
flammable vapors away.
DO NOT CONNECT 110 VAC
TO THE CONTROL VALVE.
Improper installation, adjustment,
alteration, service or maintenance
can cause injury or property dam-
age. Refer to the owner’s infor-
mation manual provided with this
appliance.
6. Ifthe appliance will not operate, follow the
instructions “To Turn Off Gas toAppliance”
and call your service technician or gas
supplier.
Do not operate the appliance with
panel(s) removed, cracked or bro-
ken. Replacement of the panel(s)
should be done by a licensed or
qualified service person.
This appliance needs fresh air for
safe operation and must be installed
so there are provisions for adequate
combustion and ventilation air.
NOT FOR USE
WITH SOLID FUEL
TO TURN OFF
If not installed, operated, and main-
tained in accordance with the man-
ufacturer’s instructions, this product
GAS TO APPLIANCE
For use with natural gas and pro-
pane. A conversion kit, as supplied
1. Turn off all electric power to the appliance
if service is to be performed.
could expose you to substances in by the manufacturer, shall be used
fuel or fuel combustion which are
known to the State of California to
cause cancer, birth defects, or other
reproductive harm.
to convert this appliance to the al-
ternate fuel.
2. Flip ON/OFF switch to the “OFF” posi-
tion.
Also Certified for Installation in a
Bedroom or a Bedsitting Room.
Keep burner and control compart-
ment clean. See installation and
operating instructions accompanying
appliance.
For assistance or additional infor-
mation, consult a qualified installer,
service agency or the gas supplier.
For additional information on operating your
Hearth & Home Technologies appliance, please refer to www.fireplaces.com.
593-913D
Final Inspection by ______________________________
42
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
C. After Appliance is Lit
Initial Break-in Procedure
CAUTION
Prevent accidental appliance operation when not
attended.
Unplug or remove batteries from remote control if absent
or if appliance will not be used for an extended period of
time.
When you light the appliance, you may notice that it pro-
duces heat which does have an associated odor or smell.
If you feel this odor is excessive it may require the initial
three to four hour continuous burn on high followed by a
second burn up to 12 hours to fully drive off any odor from
paint and lubricants used in the manufacturing process.
Condensation of the glass is normal.
•
•
•
Property damage possible from elevated temperatures.
Note: The appliance should be run three to four hours
on the initial start-up. Turn it off and let it cool completely.
Remove and clean the glass. Replace the glass and run
the appliance for an additional 12 hours. This will help to
cure the products used in the paint and logs.
CAUTION
Smoke and odors released during initial operation.
•
•
•
Open windows for air circulation.
Leave room during initial operation.
Smoke may set off smoke detectors.
During this break-in period it is recommended that some
windows in the house be opened for air circulation. This will
help avoid setting off smoke detectors, and help eliminate any
odors associated with the appliance’s initial burning.
Smoke and odors may be irritating to sensitive
individuals.
WARNING
Fire Hazard.
WARNING
Keep combustible materials, gasoline
and other flammable vapors and liquids
clear of appliance.
Fire Risk.
High Temperatures.
•
Do NOT store flammable materials in
Keep combustible household items away from appliance.
Do NOT obstruct combustion and ventilation air.
the appliance’s vicinity.
•
•
Do NOT use gasoline, lantern fuel, kerosene, charcoal
lighter fluid or similar liquids in this appliance.
Combustible materials may ignite.
•
Do NOT place combustible items on top of or in front
of appliance.
Keep furniture, draperies away from appliance.
•
D. Frequently Asked Questions
ISSUE
SOLUTIONS
This is a result of gas combustion and temperature variations. As the appliance warms, this
condensation will disappear.
Condensation of the glass
This is a result of normal operation and the flames will begin to yellow as the appliance is al-
lowed to burn for 20 to 40 minutes.
Blue flames
When first operated, this appliance may release an odor for the first several hours. This is
caused by the curing of the paint and the burning off of any oils remaining from manufactur-
ing. Odor may also be released from finishing materials and adhesives used around the
appliance.
Odor from appliance
Film on the glass
This is a normal result of the curing process of the paint and logs. Glass should be cleaned
within 3 to 4 hours of initial burning to remove deposits left by oils from the manufacturing
process. A non-abrasive cleaner such as gas fireplace glass cleaner may be necessary. See
your dealer.
Noise is caused by metal expanding and contracting as it heats up and cools down, similar to
the sound produced by a furnace or heating duct. This noise does not affect the operation or
longevity of the appliance.
Metallic noise
Is it normal to see the pilot flame burn
In an Intellifire ignition system it is normal to see the pilot flame, but it should turn off when
ON/OFF is turned off. In a standing pilot system the pilot will always stay on.
continually?
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
43
Troubleshooting
14
With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do
experience a problem, this troubleshooting guide will assist a qualified service person in the diagnosis of a problem and the
corrective action to be taken. This troubleshooting guide can only be used by a qualified service technician.
A. Intellifire Ignition System
Sympton
Possible Cause
Corrective Action
1. The ignitor/module makes
noise, but no spark.
a. Incorrect wiring.
Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor
are connected to correct terminals on module and pilot assembly.
Reversed wires at the module may cause system to make sparking
noise, but spark may not be present at pilot hood.
b. Loose connections or elec- Verify no loose connections or electrical shorts in wiring from mod-
trical shorts in the wiring.
ule to pilot assembly. Rod closest to pilot hood should be ignitor.
Verify connections underneath pilot assembly are tight; also verify
connections are not grounding out to metal chassis, pilot burner,
pilot enclosure, mesh screen if present, or any other metal object.
c. Ignitor gap is too large.
d. Faulty module.
Verify gap of igniter to pilot hood. The gap should be approximately
.17 inch or 1/8 inch.
Turn ON/OFF rocker switch or wall switch to OFF position. Remove
ignitor wire “I” from module. Place ON/OFF Rocker switch or wall
switch in ON position. Hold ground wire about 3/16 inch away from
“I” terminal on module. If there is no spark at “I” terminal module
must be replaced. If there is a spark at “I” terminal, module is fine.
Inspect pilot assembly for shorted sparker wire or cracked insulator
around electrode.
2. Pilot won’t light, there is no
noise or spark.
a. Transformer installed cor-
rectly.
Verify that transformer is installed and plugged into module. Check
voltage of transformer under load at spade connection on module
with ON/OFF switch in ON position. Acceptable readings of a good
transformer are between 3.2 and 2.8 volts AC.
b. A shorted or loose connec- Remove and reinstall the wiring harness that plugs into module.
tion in wiring configuration or
Verify there is a tight fit. Verify pilot assembly wiring to module.
wiring harness.
Remove and verify continuity of each wire in wiring harness.
c. Improper wall switch wiring. Verify that 110/VAC power is “ON” to junction box.
d. Module not grounded.
e. Faulty module.
Verify black ground wire from module wire harness is grounded to
metal chassis of appliance.
Turn ON/OFF rocker switch or wall switch to OFF position. Remove
ignitor wire “I” from module. Place ON/OFF Rocker switch or wall
switch in ON position. Hold ground wire about 3/16 inch away from
“I” terminal on module. If there is no spark at “I” terminal module
must be replaced. If there is a spark at “I” terminal, module is fine.
Inspect pilot assembly for shorted sparker wire or cracked insulator
around electrode.
3. Pilot lights but continues to
a. A shorted or loose connec- Verify all connections to wiring diagram in manual. Verify connec-
spark, and main burner will not tion in sensor rod.
ignite. (If the pilot continues to
spark after the pilot flame has
been lit, flame rectification has
not occurred.)
tions underneath pilot assembly are tight. Verify connections are
not grounding out to metal chassis, pilot burner, pilot enclosure or
screen if present, or any other metal object.
44
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
Intellifire Ignition System - (continued)
Symptom
Possible Cause
Corrective Action
3. (Continued) - Pilot lights b. Poor flame rectification or contaminated Verify that flame is engulfing sensor rod. If the pilot assem-
but continues to spark,
and main burner will not
ignite. (If the pilot contin-
ues to spark after the pilot
flame has been lit, flame
rectification has not oc-
curred.)
sensor rod.
bly does not have a ground strap, consider installing one
to increase flame rectification. Verify correct pilot orifice is
installed and inlet gas specifications. Flame carries recti-
fication current, not the gas. If flame lifts from pilot hood,
the circuit is broken. A wrong orifice or too high an inlet
pressure can cause pilot flame to lift. The sensor rod may
be contaminated. Clean sensor rod with emery cloth.
c. Module is not grounded.
Verify that module is securely grounded to metal chassis
of appliance. Verify that wire harness is firmly connected to
module.
d. Damaged pilot assembly or dirty sensor Verify that ceramic insulator around the sensor rod is not
rod.
cracked, damaged, or loose. Verify connection from sen-
sor rod to white sensor wire. Clean sensor rod with emery
cloth to remove any contaminants that may have accumu-
lated on sensor rod. Verify continuity with a multimeter with
ohms set at lowest range.
e. Faulty module.
Turn ON/OFF rocker switch or wall switch to OFF posi-
tion. Remove ignitor wire “I” from module. Place ON/OFF
Rocker switch or wall switch in ON position. Hold ground
wire about 3/16 inch away from “I” terminal on module. If
there is no spark at “I” terminal module must be replaced.
If there is a spark at “I” terminal, module is fine. Inspect
pilot assembly for shorted sparker wire or cracked insulator
around electrode.
4. Pilot sparks, but Pilot
will not light.
a. Correct gas supply.
Verify that incoming gas line ball valve is “open”. Verify that
inlet pressure reading is within acceptable limits, inlet pres-
sure must not exceed 14 in. W.C.
b. Ignitor gap is too large.
c. Module is not grounded.
Verify that spark gap from ignitor to pilot hood is .17 in. or
1/8 in.
Verify module is securely grounded to metal chassis of
appliance.
d. Module voltage output / Valve/Pilot
solenoid ohms readings.
Verify battery voltage is at least 2.7 volts. Replace batter-
ies if voltage is below 2.7.
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
45
Maintaining and Servicing Appliance
15
A. Maintenance Tasks
Although the frequency of appliance servicing and maintenance will depend on use and the type of installation, a qualified
service technician should perform an appliance checkup at the beginning of each heating season.
WARNING
CAUTION
Risk of injury or property damage.
Before servicing:
Handle glass assembly with care.
•
•
•
•
Turn off gas.
Note: Clean glass after initial 3-4 hours
operation. Longer operation without
cleaning glass may cause a permanent
white film on glass.
Turn off electricity to appliance.
Disable remote control, if one is present.
Ensure appliance is completely cooled.
After servicing:
•
•
Replace any screen or barrier that was removed.
Reseal and reinstall any venting removed for servicing.
When cleaning glass door:
•
•
•
•
•
Avoid striking, scratching or slamming glass.
Do NOT use abrasive cleaners.
Use a hard water deposit glass cleaner on white film.
Do NOT clean glass when hot.
Turn off appliance after 3-4 hours of operation and
ALLOW TO COOL.
WARNING
Annual inspection by qualified technician recommended.
•
•
Remove and clean glass assembly.
Replace glass assembly and operate appliance for
additional 12 hours.
Check:
•
•
•
•
•
•
•
•
•
Condition of doors, surrounds and fronts.
Condition of glass, glass assembly and glass seal.
Obstructions of combustion and ventilation air.
Condition of logs.
Condition of firebox.
Burner ignition and operation.
Burner air shutter adjustment
Gas connections and fittings.
Obstructions of termination cap.
Refer to maintenance instructions.
WARNING
Inspect external vent cap regularly.
Clean:
•
Ensure no debris blocks cap.
•
•
Glass
•
Combustible materials blocking cap
may ignite.
Air passageways, grilles,
control compartment
Burner, burner ports
•
Restricted air flow affects burner operation.
•
Risk of:
•
•
•
•
Fire
Delayed ignition or explosion
Exposure to combustion fumes
Odors
46
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
Inspect
Maintenance Tasks
Doors, Surrounds
and Fronts
1. Assess condition of screen and replace as necessary.
Recommend addition of screen if one is not present.
2. Inspect for scratches, dents or other damage and repair as necessary.
3. Verify no obstructions to airflow through the louvers.
4. Verify maintenance of proper clearance to combustible household objects.
1. Inspect gasket seal and its condition.
Gasket Seal, Glass
Assembly and Glass
2. Inspect glass panels for scratches and nicks that can lead to breakage when exposed to heat.
3. Confirm there is no damage to glass or glass frame. Replace as necessary.
4. Verify that latches engage properly, clip studs are not stripped, and glass attachment components are intact
and operating properly. Replace as necessary.
5. Clean glass. Replace glass assembly if severely coated with silicate deposits that cannot be removed.
Valve Compartment
and Firebox Top
1. Vacuum and wipe out dust, cobwebs, debris or pet hair. Use caution when cleaning these areas. Screw
tips that have penetrated the sheet metal are sharp and should be avoided.
2. Remove any foreign objects.
3. Verify unobstructed air circulation.
Logs
1. Inspect for broken, damaged, or missing logs. Replace as necessary.
2. Verify correct log placement and no flame impingement causing sooting. Correct as necessary.
1. Inspect for paint condition, warpage, corrosion or perforation. Sand and repaint as necessary.
2. Replace appliance if firebox has been perforated.
Firebox
Burner Ignition and
Operation
1. Verify burner is properly secured and aligned with pilot or igniter.
2. Clean off burner top, inspect for plugged ports, corrosion or deterioration. Replace burner if necessary.
3. Replace ember materials with new dime-size and shape pieces. Do not block ports or obstruct lighting paths.
4. Check for smooth lighting and ignition carryover to all ports. Verify there is no ignition delay.
5. Inspect for lifting or other flame problems.
6. Verify air shutter is clear of dust and debris.
7. Inspect orifice for soot, dirt or corrosion.
8. Verify manifold and inlet pressures. Adjust regulator as required.
9. Inspect pilot flame strength. Clean or replace orifice as necessary.
10. Inspect thermocouple/thermopile or IPI sensor rod for soot, corrosion and deterioration. Clean with emery
cloth or replace as required.
11. Verify millivolt output. Replace as necessary.
Venting
1. Inspect venting for blockage or obstruction such as bird nests, leaves, etc.
2. Confirm that termination cap remains clear and unobstructed by plants, etc.
3. Verify that termination cap clearance to subsequent construction (building additions, decks, fences or
sheds) has been maintained.
4. Inspect for corrosion or separation.
5. Verify weather stripping, sealing and flashing remains intact.
6. Inspect draft shield to verify it is not bent, damaged or missing.
1. Verify operation of remote.
Remote controls
2. Replace batteries in remote transmitters and battery-powered receivers.
3. Verify batteries have been removed from battery back-up IPI systems to prevent premature battery failure
or leaking.
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
47
Reference Materials
16
A. Appliance Dimension Diagram
Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 3.
K
L
Ø J
I
M
ELECTRICAL
ACCESS
A
H
N
GAS LINE
ACCESS
C
G
B
D
O
P
E
F
Location
Inches
8-1/4
8
Millimeters
209
Location
Inches
34-3/8
43-1/2
6-1/8
3
Millimeters
875
I*
J
A
B
203
1104
157
K
12-1/8
6
308
C
L
154
D
77
M
N
O
P*
46-3/4
86-3/4
2-7/8
7-3/8
187
E*
F*
G
H*
9-3/8
27-3/4
40
237
2203
74
706
1015
628
188
24-3/4
*All dimensions in the front to back direction are taken
from the 1/2 inch standoffs on the front face of the unit.
Figure 16.1 Appliance Dimensions
48
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Vent Components Diagrams
Effective Length
Pipe
10-1/2 in.
(267 mm)
Inches
Millimeters
°
45
Effec tive
DVP4
4
102
Height/Length
DVP6
6
12
152
305
DVP12
DVP24
DVP36
DVP48
DVP6A
4-7/8 in.
( 276 mm)
24
610
36
914
10-7/8 in.
(276 mm)
48
1219
76 to 152
DVP Pipe (see chart)
3 to 6
°
DVP45 (45 Elbow)
DVP12A 3 to 12 76 to 305
DVP12MI 3 to 12 76 to 305
DVP24MI 3 to 24 76 to 610
11-3/8 in.
(289 mm)
10 in.
(254 mm)
10 in.
(254 mm)
1 in.
(25 mm)
7-3/8 in.
(187 mm)
24 in.
(610 mm)
1-1/4 in. (32 mm)
9-1/4 in.
(235 mm)
1/2 in. TYP
(13 mm)
13-1/4 in.
(337 mm)
DVP-FS (Ceiling F ires top )
DVP-AS (Attic Shield)
DVP90ST (90° Elbow)
12 in.
(305 mm)
1 in.
(25 mm)
8 in.
(203 mm)
1- 1/2 in.
(38 mm)
10 in.
(254 mm)
14 in.
(356 mm)
UP
5 in.
(127 mm)
12 in.
(305 mm)
6 in.
(152 mm)
DVP-HVS (Vent Supp ort)
DVP-WS (Wall Shield F ires top )
Figure 16.2 DVP vent components
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
49
B. Vent Components Diagrams (continued)
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). The heat shield is designed to be
used on a wall 4 in. to 7-1/4 in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm) the
existing heat shields must be field trimmed. If wall thickness is greater than 7-1/4 in. (184 mm) a DVP-HSM-B
will be required.
8 in.
(203 mm)
Heat
Shield
15-1/8 in.
(384 mm)
EFFECTIVE LENGTH
Minimum
Term Cap
Trap1
Maximum
4-1/8 in. (105 mm) 5-5/8 in. (143 mm)
6-3/4 in. (171 mm) 10-5/8 in. (270 mm)
Trap2
Max
Effective
Length
12 in.
(305 mm)
DVP-TRAP
Horizontal Termination Cap
DVP-TRAP1
DVP-TRAPK2
DVP-TRAP2
DVP-TRAPK1
DVP-TRAPFL
Flashing
DVP-VTI
DVP-TH
Figure 16.3 DVP vent components
50
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Vent Components Diagrams (continued)
7-3/8 in.
(187 mm)
1-1/2 in.
(38 mm)
7-1/4 in.
(184 mm)
12-1/2 in.
(318 mm)
17-3/4 in.
(451 mm)
14 in.
(356 mm)
5-1/4 in.
(133 mm)
DVP-TVHW
Vertical Termination Cap
12 in.
(305 mm)
(High wind)
DVP-TB1
Basement Vent Ca
p
DVP-HSM-B
Extended Heat Shield
31 in.
(787 mm)
13-1/4 in.
(367 mm)
24-5/8 in.
(625 mm)
3-7/8 in.
(98 mm)
27-1/2 in.
(127 mm)
24-5/8 in.
(625 mm)
10-1/2 in.
(267 mm)
13-1/4 in.
(367 mm)
RF6M
Roof Flashing Multi-pak
RF12M
Roof Flashing Multi-pak
DVP-TV
Vertical Termination Cap
11-7/8 in.
(302 mm)
5 in.
(127 mm)
5 in.
(127 mm)
13-3/4 in.
(349 mm)
13-7/8 in.
(352 mm)
13-3/4 in.
(349 mm)
BEK
DVP-BEK2
Trap Cap Brick Extension
DVP-HPC Cap Brick Extension
DVP and SL Series Components
13-7/8 in.
(352 mm)
9-1/2 in.
(241 mm)
11-5/8 in .
(295 mm)
12-1/8 in.
(308 mm)
14 in.
(356 mm)
7-1/8 in.
(181 mm)
5-3/4 in.
(146 mm)
DRC-RADIUS
Cap Shield
COOL-ADD
Cap Shield
Figure 16. 4
DVP vent components
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
51
B. Vent Components Diagrams (continued)
8-1/8 in.
13 in.
(206 mm)
(330 mm)
15 in.
(381 mm)
DVP-HRC, DVP-HRC-SS
NOT APPROVED FOR ALL UNITS.
Effective Length
5-3/4 to 8-3/8 in.
146 to 213 mm
5-1/2 in. 8-3/8 in.
140 mm 213 mm
3°
87°
10-1/2 in.
267 mm
10-7/8 in.
276 mm
DVP-HRC-ZC, DVP-HRC-ZC-SS
NOT APPROVED FOR ALL UNITS.
Figure 16. 5
DVP Vent Components
52
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
BRAVO
C. Service Parts List
Service Parts Diagram
Beginning Manufacturing Date: Mar. 2002
Ending Manufacturing Date: ______
7
8
9
11
10
17
12
13
16
15
14
Log Set Assembly
1
6
2 5
4
3
Part number list on following page.
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
53
Download from Www.Somanuals.com. All Manuals Search And Download.
C. Service Parts List
BRAVO
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
Stocked
at Depot
ITEM
DESCRIPTION
SERIAL #
PART NUMBER
LOGS-BRAVO
SRV750-703
SRV750-705
SRV750-706
SRV750-704
SRV704-702
SRV704-701
704-192
Log Set Assembly
Log 1 Back Log
Y
N
N
N
N
N
N
N
Y
Y
Y
Y
Y
Y
N
N
Y
N
Y
Y
Y
Y
Y
Y
N
N
N
Y
1
2
3
4
5
6
7
8
Log 2 Right Inside Log
Log 3 Small Log
Log 4 Left Inside Log
Log 5 Right Log
Log 6 Left Log
Non-combustible board
Glass Latch Assembly
386-122A
Pre 002881385
SRV704-178-NG
Pilot Assembly NG (must order whole assembly)
Pilot Assembly LP (must order whole assembly)
Post 002881385 2090-012
9
Î
Pre 002881385
Post 002881385 2090-013
567-301A
SRV704-178-LP
18” Flex 3/8” Diameter
Finishing Strips
Glass Retainer
Glass Door Assembly
Log Grate
10
11
12
13
14
704-233
704-235
GLA-BRAVO
704-360A
Burner NG
704-176A
15
Burner LP
704-175A
Pre Oct 2004
Post Oct 2004
100-250A
16
17
Junction Box
4031-013
Battery Pack
3V Adaptor
593-594A
593-593A
Lava Rock Bag
Mineral Wool
Patch Kit
705-420
050-721
SRV-PACK-CFX
MESH-BRAVO
Mesh Assembly
Conversion Kit NG
Conversion Kit LP
Pilot Orifice NG
Pilot Orifice LP
Regulator NG
NGKP-BRAVO
LPKP-BRAVO
593-528
Y
Y
Y
Y
Y
Y
593-527
NGK-DXF
LPK-DXF
Regulator LP
Additional service part numbers appear on following page
54
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
BRAVO
C. Service Parts List
Valve Assembly Parts List
Beginning Manufacturing Date: Mar. 2002
Ending Manufacturing Date: ______
Intermittent Pilot Ignition
Valve Assembly
1
2
3
4
7
5
6
8
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
Stocked
at Depot
ITEM
DESCRIPTION
Flex Ball Valve Assembly
SERIAL #
PART NUMBER
302-320A
593-500
1
Y
Y
Y
N
Y
Y
N
Y
Y
Y
Y
Y
Valve NG
2
Valve LP
593-501
Valve Bracket Plate
Wire Assembly
Module
704-246
3
4
5
6
7
593-590A
593-592
Valve Bracket
Jumper Wire
704-146
2012-206
593-596A
2045-024
060-800
Wire Assembly
Thermostat Wire Assembly
Orifice NG (#42A)
Orifice LP (#53A)
Pre Oct 2004
Post Oct 2004
8
060-801
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
55
D. Limited Lifetime Warranty
LIMITED LIFETIME WARRANTY
HEAT & GLO GAS APPLIANCE PRODUCTS
BASIC ONE-YEAR WARRANTY. HEAT & GLO, a brand of HEARTH & HOME TECHNOLOGIES INC., located at 20802 Kensington Boulevard,
Lakeville, MN 55044, (“HEAT & GLO”) warrants to the original owner that your new HEAT & GLO Gas Appliance (the “Product”) will be free
from defects in materials and workmanship for a period of one year from the date of installation. During the first year, HEAT & GLO will replace
or repair, at its discretion, any defective components at its sole cost and expense, including payment of all reasonable labor costs incurred in
replacing or repairing such components. This basic warranty is subject to the conditions, exclusions and limitations described below.
EXTENDED LIFETIME COVERAGE. HEAT & GLO warrants that the firebox, heat exchanger, log(s), and burner will not be defective in mate-
rial or workmanship during the period the Product is owned by the original owner, subject to the following conditions, exclusions and limitations
described below.
CONDITIONS, EXCLUSIONS AND LIMITATIONS:
1. This warranty applies to the original owner only and is nontransferable.
2. This warranty applies only to Products installed in the United States of America or Canada.
3. This warranty is limited to the replacement or repair of defective components or workmanship and HEAT & GLO may fully discharge all
obligations under this warranty by repairing or replacing, at its discretion, the defective components. The maximum amount recoverable
under this warranty is limited to the purchase price of the Product and, if HEAT & GLO is unable to provide replacement or repair in an
expedient and cost-effective manner, HEAT & GLO may discharge all obligations under this warranty by refunding the purchase price of
the Product. IN NO EVENT SHALL HEAT & GLO BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY
DEFECTS IN THE PRODUCT.
4. Any labor and related repair charges relating to the costs and expenses of replacing or repairing defective components under the Limited
Lifetime Warranty are not covered by this warranty, except as provided for under the Basic One-Year Warranty.
5. Components and parts made by other manufacturers, whether sold with the Product or added thereafter, are NOT covered by this warranty
unless expressly authorized and approved by HEAT & GLO in writing.
6. Any damages caused by environmental conditions, inadequate ventilation or drafting caused by tight sealing construction of the structure,
air handling devices such as exhaust fans or forced air furnaces, or other such causes are not covered by this warranty.
7. This warranty will be void if:
a) The Product is not installed, operated and maintained in compliance with local building codes and with the instructions in the Installer’s
Guide, Owner’s Guide and Listing Agent Identification Label furnished with the Product.
b) Any parts or components made by other manufacturers are added or used in the Product, unless expressly authorized and approved
by HEAT & GLO in writing.
c) Any service work is performed on the Product by anyone other than an authorized HEAT & GLO representative.
d) The Product is damaged due to shipping, improper handling, accident, abuse or misuse.
e) Fuels other than those specified in the Installer’s Guide and Owner’s Guide are used.
f) Modification was made to the Product which was not expressly authorized and approved by HEAT & GLO in writing.
EXCEPT TO THE EXTENT PROVIDED BY LAW, HEAT & GLO MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY
SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO THE DURATION OF THE WARRANTY SPECIFIED
ABOVE.
Some states do not allow limitations on how long an implied warranty lasts, or do not allow exclusion or limitation of incidental or consequential
damages, so those limitations may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which
vary from State to State.
If warranty service is needed you should contact your installing dealer and if the installing dealer is unable to provide necessary parts or com-
ponents, contact the nearest authorized HEAT & GLO dealer or supplier.
NOTES TO CUSTOMER:
1. In order to insure proper installation, operation and maintenance HEAT & GLO strongly recommends annual ser-
vicing by an authorized HEAT & GLO dealer.
2. Please complete this information and retain this warranty in a safe place for future reference: Installation Date:______
Model #:_________________ Serial #:______________ Installing Contractor:_________________________
3. HEAT & GLO reserves the right to make changes at any time, without notice, in design, material, specifications
and prices of the Product. HEAT & GLO also reserves the right to discontinue styles and products.
© 2007 Hearth & Home Technologies Inc.
060-981E 10/07
56
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
E. Contact Information
Heat & Glo, a brand of Hearth & Home Technologies Inc.
20802 Kensington Boulevard, Lakeville, MN 55044
Please contact your Heat & Glo dealer with any questions or concerns.
For the location of your nearest Heat & Glo dealer,
- NOTES -
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
CAUTION
DO NOT DISCARD THIS MANUAL
Important operating
and maintenance in-
structions included
Read, understand and
follow these instructions
for safe installation and
operation.
Leave this manual with party
responsible for use and operation.
•
•
•
This product may be covered by one or more of the following patents: (United States) 4593510, 4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471,
5328356, 5341794, 5347983, 5429495, 5452708, 5542407, 5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099, 6048195,
6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942, 6769426,
6774802, 6796302, 6840261, 6848441, 6863064, 6866205, 6869278, 6875012, 6880275, 6908039, 6919884, D320652, D445174, D462436; (Canada) 1297749, 2195264, 2225408, 2313972; (Australia)
780250, 780403, 1418504 or other U.S. and foreign patents pending.
Printed in U.S.A. - Copyright 2008
Heat & Glo • Bravo • 704-902 Rev. E • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
57
|