Mini rolling Mill
With 5 rollers
Model 4832
set up And operAting instructions
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
distributed exclusively by harbor Freight tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
read this material before using this product.
Failure to do so can result in serious injury.
sAVe this MAnuAl.
©
®
Copyright 2007 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
the working conditions and the work to be performed. Use of the product for
operations different from those intended could result in a hazardous situation.
serVice
1.
2.
Have product serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the product is maintained.
Maintain labels and nameplates on the product. These carry important safety
information. If unreadable or missing, contact Harbor Freight Tools for a
replacement.
MiscellAneous
1.
2.
Keep hands clear of the gears and rollers of the Rolling Mill.
Do not exceed the minimum or maximum gauge of wire or sheet stock listed for
this product.
3.
The warnings, precautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be
understood by the operator that common sense and caution are factors which
cannot be built into this product, but must be supplied by the operator.
sAVe these instructions.
SKU 4832
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
speciFicAtions
Wire - .031” to .197”
Sheet - 35 Gauge to .079”
Capacity
Gears
3:1 Gear Ratio
2 Smooth Rollers
1 Wire Roller
Includes
2 Pattern Rollers
unpAcking
When unpacking, check to make sure that the item is intact and undamaged. If
any parts are missing or broken, please call Harbor Freight Tools at the number shown
on the cover of this manual as soon as possible.
set up instructions
read the entire iMportAnt sAFety inForMAtion section at the
beginning of this manual including all text under subheadings therein
before set up or use of this product.
note: For additional information regarding the parts listed in the following pages, refer
to the Assembly Diagram near the end of this manual.
Assembly
1.
2.
3.
Remove the protective plastic coverings from all items including the attached
Rollers.
Connect the Operating Handle (1) to the Shaft Gear (10) with Bolt (11) and
Washer (12), as shown on the cover.
Slide the Working Handle (2) between the Right and Left Screw Gears (4,5) into
the hole on top of the unit.
Mounting
1.
The Mill must be mounted before use. Choose a work surface that is flat, level,
and capable of bearing the weight of the Mill and workpieces.
2.
3.
Operating Handle must be positioned to rotate freely.
Using the Base of the Mill as a template, mark with a pencil where the holes need
to be drilled. Verify that installation surface has no hidden utility lines before
drilling.
4.
Drill holes in the work surface and mount the Mill firmly using appropriate
hardware (not included).
SKU 4832
For technical questions, please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
inserting rollers
1.
2.
3.
Remove the uppermost Bolt (11) and Washer (12) from Side Gear (7).
Remove Side Gear located below Right Screw Gear (4). See Figure 1.
Remove Left Screw Gear (5) and Right Screw Gear (4) from the Mill body by
turning counterclockwise.
Figure 1
4.
5.
Remove all four Bolts (11) from Cover (6) of
the Mill. Pull Cover up and off.
pull side gear (7)
from here
With the Cover off, pull Roller and Plates (13)
up and out of Mill.
shaft gear (10)
side gear (7)
6.
7.
Choose the correct Roller for the job.
Bolt (11) &
Washer (12)
Remove Plates from end of Roller that was
in the machine and install on the end of the
chosen Roller.
8.
9.
Slide Plates and desired Roller back down into Mill body. Attach the Side Gear.
Place the Cover back on the unit.
Thread Bolt with Washer back into place on the body.
operAting instructions
read the entire iMportAnt sAFety inForMAtion section at the
beginning of this manual including all text under subheadings therein
before set up or use of this product.
1.
Choose the desired Roller. The Mini-Rolling Mill comes with five different Rollers:
two Smooth Rollers (15), two
Figure 2
Pattern Rollers (17), and a
Wire Roller (16). Choose the
Roller with the pattern best
suited to your workpiece.
Install as directed in the
Assembly section of this
manual.
Working handle (2)
oil reservoir (18)
operating
handle (1)
shaft gear (12)
2.
Fill the Oil Reservoir (18) with
high quality light machine oil.
Bolt (11) & Washer (12)
caution. keep hands clear of gears and rollers during operation. the gears and
rollers can cause injury.
REV 09a
SKU 4832
For technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
2.
Turning the Working Handle will raise or lower the top roller, changing the amount
of space between the Rollers. This will also determine the depth of indentation
that is made by the Roller.
3.
4.
Insert the workpiece and turn the Operating Handle to pull it through the Rollers.
Clean, then store the product indoors, out of children’s reach.
MAintenAnce And serVicing
damaged products can fail, causing personal injury. do
not use a damaged product. if abnormal noise or vibration
cAution
occurs, have the problem corrected before further use.
cleaning, maintenance, and lubrication
1.
2.
BeFore eAch use, inspect the general condition of the product. Check for
loose screws, misalignment or binding of moving parts, cracked or broken parts,
and any other condition that may affect its safe operation.
AFter use, clean external surfaces of the product with clean, moist cloth.
pleAse reAd the FolloWing cAreFully
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLy
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLy. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANy REPRESENTATION OR WARRANTy OF ANy KIND TO THE BUyER THAT
HE OR SHE IS qUALIFIED TO MAKE ANy REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
qUALIFIED TO REPLACE ANy PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR
DISTRIBUTOR ExPRESSLy STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE
UNDERTAKEN By CERTIFIEDAND LICENSED TECHNICIANS, AND NOT By THE BUyER. THE BUyER
ASSUMES ALL RISK AND LIABILITy ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL
PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION
OF REPLACEMENT PARTS THERETO.
SKU 4832
For technical questions, please call 1-800-444-3353.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
pArts list & AsseMBly diAgrAM
part
description
Operating Handle
Qty
1
part
10
description
Shaft Gear
Qty
1
1
2
3
4
5
6
7
8
9
Working Handle
Handle Gear Screw
Right Screw Gear
Left Screw Gear
Cover
1
11
Bolt
9
1
12
Washer
5
1
13
Plates
2
1
14
Plate Fitting
1
1
15
Smooth Roller (one shown)
Wire Roller
2
Side Gear
1
16
1
Side Gear
1
17
Pattern Roller (one shown)
Oil Reservoir
2
Main Gear
1
18
1
SKU 4832
For technical questions, please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
liMited 1 yeAr WArrAnty
Harbor Freight Tools Co. makes every effort to assure that its products meet high
quality and durability standards, and warrants to the original purchaser that this product is
free from defects in materials and workmanship for the period of one year from the date
of purchase (90 days if used by a professional contractor or if used as rental equipment).
This warranty does not apply to damage due directly or indirectly, to misuse, abuse,
negligence or accidents, repairs or alterations outside our facilities, normal wear and tear,
or to lack of maintenance. We shall in no event be liable for death, injuries to persons or
property, or for incidental, contingent, special or consequential damages arising from the
use of our product. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation of exclusion may not apply to you. THIS
WARRANTy IS ExPRESSLy IN LIEU OF ALL OTHER WARRANTIES, ExPRESS OR
IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITy AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the complaint
must accompany the merchandise. If our inspection verifies the defect, we will either
repair or replace the product at our election or we may elect to refund the purchase price
if we cannot readily and quickly provide you with a replacement. We will return repaired
products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning
the product.
This warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
record product’s serial number here:
note: If product has no serial number, record month and year of purchase instead.
note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
SKU 4832
For technical questions, please call 1-800-444-3353.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
|