Hasbro Door PUB 0804 User Manual

1
Illuminator Glider Door  
Installation Manual  
Ultimate Products Inc. • 2319 Laurelbrook Street• Raleigh, NC 27604 • (800) 542-7221 • Fax (919) 834-4526  
PUB 0804  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3
Parts Identification  
AP1075:  
3/8" x 1/4"  
Reducing elbow  
quick connect  
AP1078:  
Male Tube Stem  
QD100:  
Quick Exhaust Valve  
GLP2003 - Glider Pulley with  
Bolt and Nut  
CV100:  
Cam Valve  
AP1080:  
3/8” x 1/4”  
male quick connect  
AP1050:  
Turnbuckle  
B
A
GB2003A:  
Bracket ‘A’  
GB2003B:  
Bracket ‘B’  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
Parts Identification Continued  
A - 1  
B - 1  
B - 2  
A - 2  
B-1: Left Hand Glider Stop  
B-2: Right Hand Glider Stop  
A-1: Left Hand Glider Guide  
A-2: Right Hand Glider Guide  
C - 1  
D- 1  
D- 2  
C - 2  
D-1: Left Hand Slotted Glider Stop  
D-2: Right Hand Slotted Glider Stop  
C-1: Left Hand Slotted Glider Stop  
C-2: Right Hand Slotted Glider Stop  
E- 1  
E- 2  
E-1: Left Hand Wall Guide  
E-2: Right Hand Wall Guide  
A
B
Download from Www.Somanuals.com. All Manuals Search And Download.  
5
A
1
Insure that Walls on each side of door  
opening are clear of all obstructions  
(Door will protrude 5 1/2”  
Into building)  
Installing Door track w/ operator  
2
1”  
Install bottom of door track 1” above door  
opening  
Door Opening  
Right hand side of door track MUST BE INSTALLED EXACTLY  
IN CENTER OF DOOR OPENING!  
center of opening  
Above the left hand side of door  
opening install track w/ operator  
As shown in Figure B  
3
B
Place the bottom of track on line that  
was drawn 1” above opening  
as described above.  
Make sure track is level!  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6
Panel Identification:  
Panel #1  
Panel #2  
Panel #3  
Panel #4  
Install all panels w/ center  
Brace on inside of building  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7
5
C
Slide Panel #1 & 2 (see page 4)  
Into track #1 As shown in  
figure C and step number 6 below.  
Make sure center  
brace is on the inside of building  
Slide Panel #4 (Clear Section)  
D
6
Into track #2  
As shown in figure D  
*Rubber astragal is on the right side  
of door panel  
Track #1  
Track #2  
7
8
Slide Panel #3 (Clear Section)  
E
Into track #2  
As shown in figure E  
*Rubber astragal is on the left side  
of door panel  
Hang right side track ( track without  
Operator ) as shown in Figure F  
(This track will be flush with track  
shown in Figure E)  
F
Place the bottom of track on line that  
was drawn 1” above opening.  
Make sure track is level!!  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8
Slide panels #2 and #3 to the right hand side of track-  
The track that does not have the operator  
9
Place all panels as shown on page 4 so the door is in the closed  
position  
Preparing to install Glider blocks and Guides  
10  
A - 1  
A - 2  
B - 1  
B - 2  
C - 1  
C - 2  
D- 1  
D- 2  
E- 1  
E- 2  
See the following pages for installation of these parts  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9
Install Blocks on Door Sections  
11  
With Door Sections in  
Closed position:  
Install Items ‘B-1,C-1, and  
‘D-1’ on Panel #2 and  
Panel #4 as shown  
B - 1  
C - 1  
Install Items ‘B-2’, ‘C-2’  
and ‘D-2’ on Panel #1  
Panel #4  
Panel #2  
D- 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
Install Items ‘A-1’and‘A-2’  
12  
Panel #2  
Panel #4  
A - 1  
**IMPORTANT - MAKE SURE DOOR  
IS COMPLETELY CLOSED AS SHOWN  
ON PAGE 4  
A - 1  
With Door Sections in Closed position:  
Install item ‘A-1’ on Panel #2. The guide  
bar is inserted into slot of A-1 as shown  
Follow same steps when installing item  
‘A-2’ on Panel #1 (no picture shown)  
GSP: Glider Spacer for  
cross brace  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11  
Install Items ‘E-1’and ‘E-2’  
Panel #2  
13  
Keeping Door in Closed Position:  
Insert item ‘E-1’ onto guide bar  
Panel #4  
of panel #2 and attach to wall with  
screws. (screws not provided)  
E- 1  
E- 1  
Install Item ‘E-2’ on Panel #1 as shown in  
step number 13 above  
14  
Preparing to install  
Door Brackets:  
Close panels to meet in  
the center  
15  
A
3”  
3”  
B
Download from Www.Somanuals.com. All Manuals Search And Download.  
12  
Install Bracket ‘A’  
16  
*Important: Push Operator Rod fully into cylinder.  
Now pull operator rod out of cylinder 1/4”  
A
Slide Bracket ‘A’ onto operator  
rod and position bracket ‘A’ 3” from edge of door  
as shown on step #17. Now attach aluminum block  
to operator rod as shown  
Pre Drill holes for Brackets ‘A’ and ‘B’  
17  
Attach Bracket ‘A’ to Panel #4 and Bracket ‘B’ to Panel #3 as shown  
Make sure brackets are attached 3” from edge of door as shown  
A
3”  
3”  
B
Install Door Cables  
18  
Position turnbuckle in center of door opening as shown above  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13  
Run cable through top slot  
of bracket ‘A’:  
19  
Tighten bolts of aluminum block  
down onto cable.  
H
A
Run cable around top of pulley on right side of track  
and through top slot of aluminum block on bracket ‘B’ (do not tighten  
20  
block until later)  
Air Powered Operator  
8 1/4”  
Track  
Door  
Opening  
Door  
Opening  
33” minimum  
33” minimum  
Continue running cable around bottom of pulley on  
left side of track. Connect cables together in center  
with turnbuckle.  
21  
Tighten cable by adjusting turnbuckle.  
Do not over-tighten. Tighten aluminum block on bracket ‘B’  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14  
Install brush on bottom of door sections  
22  
Install brush on bottom of each  
panel so that brush angles in-  
ward as shown. (Brushes will  
angle toward each other)  
Bottom of brush should touch  
floor for a proper seal.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
15  
Install floor guides  
23  
Space Items ‘J’ & ‘K’ 2 1/4” apart  
Make sure center of floor guides are  
in center of door opening  
K
J
Place item ‘J’ even w/ door opening  
Install Air Fittings  
24  
Figure 1  
Figure 2  
Figure 3  
Install fitting to  
Figure 3 and here  
Install fittings to  
Figure 1 & 2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
18  
Door opening requirements for Glider Door  
For 10’ opening— Minimum of 33” of side room on each side  
Operator will open the door 9’9” wide leaving 1 1/2” of door in opening  
Make Floor level! Track and operator weight approx. 155 pounds.  
Track w/ operator extends 8 1/2” above door opening.  
Track is fastened to wall w/ self tapping screws 2’ apart.  
Air Powered Operator  
8 1/4”  
Track  
Door  
Opening  
Door  
Opening  
33” minimum  
33” minimum  
Maximum 1/4” variance  
Make floor level from side wall to center  
Of door opening. Door extends 5 1/4”  
into building  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Graco Car Seat PD182092A User Manual
Hamilton Beach Coffeemaker 840073500 User Manual
Hamilton Beach Humidifier 76375 User Manual
Harbor Freight Tools Paint Sprayer 94572 User Manual
Heath Zenith Universal Remote 598 1135 08 User Manual
Hotpoint Microwave Oven BS61 MK2 User Manual
HP Hewlett Packard Camera Accessories YTH 2242 T User Manual
HP Hewlett Packard Laptop VC4815 User Manual
Hustler Turf High Chair Hustler ATZ User Manual
iHome Speaker System iHM10 User Manual