Harman Kardon CD Player 76 User Manual

CDR 20 CDRecorder  
OWNER’S MANUAL  
0
®
Power for the digital revolution.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Introduction  
Thank you for choosing Harman Kardon.  
The CDR 20 CD Player/Recorder is a unique  
product, designed not only to play back your  
existing library of compact discs, but also to  
record compact discs from either analog or digi-  
tal programs. You may feed signals (for record-  
ing) to the CDR 20 from external sources such  
as an A/V receiver, a tuner, a tape deck or a CD  
player, or you may simply place a CD in one  
deck, and make a copy using a recordable CD  
in the other deck.  
Special Features  
Important Information About CD  
Recording  
Dual-Deck CD Player and CD-R/CD-RW  
Recorder  
In order to get the most enjoyment from your  
new CD-R recorder, please pay special attention  
to the following sections of the manual that  
provide information about the special features  
and capabilities of CD Recorders.  
X4 Dub Speed for Both CD-R and  
Erasable CD-RW Discs  
Audiophile-Grade Digital-to-Analog  
Converters for Highest Audio Quality  
The CDR 20 plays all standard CD audio  
discs but for recording, the CDR 20 uses  
special CD-R and CD-RW discs designed  
only for audio use. CD-R discs designed for  
computer use will not work in the CDR 20.  
See page 14 for more information on which  
types of discs are used with the CDR 20.  
Dual-Play Capability  
Extensive Playback Programming  
Capabilities  
Designed and engineered by Harman Kardon,  
the CDR 20 is among the first audio CD  
recorders with x4 speed capability. This means  
that it will take only 15 minutes to copy a  
60-minute disc.  
Coaxial and Optical Digital Inputs and  
Outputs  
The last step in making a CD-R recording is  
the finalization process. Unless this step is  
properly done, the disc will not work in other  
players. See page 22 for information on  
finalizing discs.  
Front-Panel Coaxial Digital Input for  
Use with Portable Devices  
The CDR 20 not only records with the highest  
speed and quality available but it is also an  
audiophile CD player. Through the use of  
Sample-Rate Converter Allows Use of  
DAT Players as Digital Source  
Ergonomic Remote Control  
Once finalized, CD-R discs will play in any  
CD player, but CD-RW discs will only play in  
the CDR 20 and certain other machines.  
Check the specifications of your CD player if  
you have questions about compatibility with  
CD-RW discs.  
audiophile-grade digital-to-analog converters  
(DACs), the CDR 20s performance rivals the  
most sophisticated high-end players. Should  
you wish to bypass the internal DACs and use  
an external digital processor, coax and optical  
digital outputs are available. Thanks to the CDR  
20s dual-tray design, you may even play back  
two separate discs at the same time, for parties  
or multi-room applications. To make CD play-  
back more enjoyable, the CDR 20 also features  
a wide range of program and repeat functions.  
As with all CD players, except those  
designed specifically for portable use, you  
should never move a CD player while there  
is a disc inside one of the decks. NEVER  
move the CDR 20 until discs have been  
removed from both decks.  
Since CD recorders are a relatively new technol-  
ogy, this may be your first CD-R product.  
Although CD recorders resemble play-only CD  
machines in many ways, there are some impor-  
tant differences between a standard CD and a  
CD-R. In addition, making a CD-R recording is  
also a different process than what you may be  
familiar with for making audio tape or cassette  
recordings. For that reason, we encourage you  
to read through this manual so that you are  
fully acquainted with the way CD recording  
works. This small investment in your time will  
pay major dividends in the enjoyment that will  
result from proper use of the CDR 20.  
CAUTION  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
CAUTION: To prevent electric shock,  
do not use this (polarized)  
plug with an extension cord,  
receptacle or other outlet  
unless the blades can  
be fully inserted to  
prevent blade exposure.  
The lightning flash with arrowhead symbol,  
within an equilateral triangle, is intended to  
alert the user to the presence of uninsulated  
“dangerous voltage” within the product’s  
If you have additional questions about this  
product – its installation or operation – that are  
not answered in this manual, please contact  
your dealer, who is your best source of local  
information. You may also contact Harman  
Kardon via e-mail through our Web site at  
enclosure that may be of sufficient magnitude to constitute a  
risk of electric shock to persons.  
The exclamation point within an equilateral  
triangle is intended to alert the user to the  
presence of important operating and  
maintenance (servicing) instructions in the  
literature accompanying the appliance.  
3 INTRODUCTION  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety Information  
the unit on a shelf, be certain that the shelf  
and any mounting hardware can support the  
weight of the product.  
antee that harmful interference will not occur in  
a particular installation. If this equipment does  
cause harmful interference to radio or television  
reception, which can be determined by turning  
the equipment off and on, the user is encour-  
aged to try to correct the interference by one or  
more of the following measures:  
Important Safety Information  
Verify Line Voltage Before Use  
Your CDR 20 has been designed for use with  
100- to 240-volt AC current. Connection to a  
line voltage other than that for which it is  
intended can create a safety and fire hazard  
and may damage the unit.  
Make certain that proper space is provided  
both above and below the unit for ventila-  
tion. If this product will be installed in a  
cabinet or other enclosed area, make certain  
that there is sufficient air movement within  
the cabinet.  
Reorient or relocate the receiving antenna.  
If you have any questions about the voltage  
requirements for your specific model, or about  
the line voltage in your area, contact your sell-  
ing dealer before plugging the unit into a wall  
outlet.  
Increase the separation between the equip-  
ment and receiver.  
Do not place the unit directly on a carpeted  
surface.  
Connect the equipment into an outlet on a  
circuit different from that to which the  
receiver is connected.  
Avoid installation in extremely hot or cold  
locations, or an area that is exposed to direct  
sunlight or heating equipment.  
Do Not Use Extension Cords  
Consult the dealer or an experienced  
Avoid moist or humid locations.  
We do not recommend that extension cords be  
used with this product. As with all electrical  
devices, do not run power cords under rugs or  
carpets or place heavy objects on them.  
Damaged power cords should be replaced  
immediately by an authorized service depot  
with cords meeting factory specifications.  
radio/TV technician for help.  
Do not obstruct the ventilation slots on the  
top of the unit, or place objects directly over  
them.  
This device complies with Part 15 of the FCC  
Rules. Operation is subject to the following two  
conditions: (1) this device may not cause harm-  
ful interference, and (2) this device must accept  
interference received, including interference that  
may cause undesired operation.  
Cleaning  
When the unit gets dirty, wipe it with a clean,  
soft dry cloth. If necessary, wipe it with a soft  
cloth dampened with mild soapy water, then a  
fresh cloth with clean water. Wipe dry immedi-  
ately with a dry cloth. NEVER use benzene,  
aerosol cleaners, thinner, alcohol or any other  
volatile cleaning agent. Do not use abrasive  
cleaners, as they may damage the finish of  
metal parts. Avoid spraying insecticide near  
the unit.  
Handle the AC Power Cord Gently  
When disconnecting the power cord from an  
AC outlet, always pull the plug, never pull the  
cord. If you do not intend to use the unit for  
any considerable length of time, disconnect the  
plug from the AC outlet.  
NOTE: Changes or modifications may cause  
this unit to fail to comply with Part 15 of the  
FCC Rules and may void the users authority to  
operate the equipment.  
Unpacking  
The carton and shipping materials used to pro-  
tect your new receiver during shipment were  
specially designed to cushion it from shock and  
vibration. We suggest that you save the carton  
and packing materials for use in shipping if you  
move, or should the unit ever need repair.  
Do Not Open the Cabinet  
There are no user-serviceable components  
inside this product. Opening the cabinet may  
present a shock hazard, and any modification  
to the product will void your guarantee. If water  
or any metal object such as a paper clip, wire  
or a staple accidentally falls inside the unit, dis-  
connect it from the AC power source immedi-  
ately, and consult an authorized service station.  
Moving the Unit  
Before moving the unit, be certain to discon-  
nect any interconnection cords with other com-  
ponents, and make certain that you disconnect  
the unit from the AC outlet.  
To minimize the size of the carton in storage,  
you may wish to flatten it. This is done by care-  
fully slitting the tape seams on the bottom and  
collapsing the carton down to a more two-  
dimensional appearance. Other cardboard  
inserts may be stored in the same manner.  
Packing materials that cannot be collapsed  
should be saved along with the carton in a  
plastic bag.  
IMPORTANT NOTE: To avoid damage to the  
CDR 20 which may not be covered by the war-  
ranty, be certain that all discs are removed from  
the unit before it is moved. Once the CDR 20 is  
installed, discs may be left in the unit when it is  
turned off, but the unit should NEVER be  
moved with discs left in either deck.  
CAUTION: The CDR 20 uses a laser system. To  
prevent direct exposure to the laser beam, do  
not open the cabinet enclosure or defeat any of  
the safety mechanisms provided for your pro-  
tection. DO NOT STARE INTO THE LASER BEAM.  
To ensure proper use of this product, please  
read this owners manual carefully and retain it  
for future use. Should the unit require mainte-  
nance or repair, please contact your local  
Harman Kardon service station. Refer servicing  
to qualified personnel only.  
Important Information for the User  
This equipment has been tested and found to  
comply with the limits for a Class B digital  
device, pursuant to Part 15 of the FCC Rules.  
The limits are designed to provide reasonable  
protection against harmful interference in a  
residential installation. This equipment generates,  
uses and can radiate radio frequency energy and,  
if not installed and used in accordance with the  
instructions, may cause harmful interference to  
radio communication. However, there is no guar-  
If you do not wish to save the packaging mate-  
rials, please note that the carton and other sec-  
tions of the shipping protection are recyclable.  
Please respect the environment and discard  
those materials at a local recycling center.  
Installation Location  
To assure proper operation and to avoid the  
potential for safety hazards, place the unit  
on a firm and level surface. When placing  
4 SAFETY INFORMATION  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Front-Panel Controls  
¯
¸
ˆ
Ù
Ú
Ó
*
˘
˜
Û
Ò
Ô
&
ı
(
0
3
5
7
9
!
#
%
1
2
8
4
)
@
$
^
6
1 Power Switch  
2 Status-Mode Indicator  
3 Play Deck  
4 Headphone Jack  
5 Headphone Level Control  
6 Digital Input  
7 Play-Deck Open  
8 Record Button  
9 CD Sync  
@ Finalize  
# Speed  
$ Record-Deck Open  
% Record Deck  
^ Analog-Record Level Control  
& Record-Deck Stop  
* Record-Deck Play/Select  
( Record-Deck Pause  
Ó Record-Deck Next  
Ò Record-Deck Display Select  
Ú Information Display  
Û Remote Sensor  
Ù Play-Deck Display Select  
ı Dual-Play Selector  
ˆ Play-Deck Next  
˜ Play-Deck Previous  
¯ Play-Deck Pause  
˘ Play-Deck Play  
) Dubbing  
! Erase  
Ô Record-Deck Previous  
Input Select  
¸ Play-Deck Stop  
1 Power Switch: Press this switch to apply  
power to the CDR 20. When the unit is first  
turned on, the Status-Mode Indicator 2  
surrounding the switch will turn green. Once  
the unit has been turned on with this switch, it  
may be operated from either the front panel or  
remote control. Press the switch again to turn  
the unit completely off.  
4 Headphone Jack: Connect standard head-  
phones to this jack for private listening.  
9 CD Sync: Press this button once to begin  
an automated recording of a single track from  
an external CD player when a digital connec-  
tion is used. Press it twice to begin automated  
recording of an entire disc. See page 21 for  
more information on CD Sync recording.  
5 Headphone Level Control: Turn this  
control to adjust the volume level to the head-  
phones. Note that the use of this control will  
not change the analog output levels at the  
rear-panel audio outputs ¡™.  
) Dubbing: Press this button to begin the  
process of making a complete copy of the disc  
in the Play Deck 3 to a CD-R or CD-RW disc  
in the Record Deck %. See page 20 for more  
information on dubbing.  
6 Digital Input: This coaxial digital input  
may be used to connect a portable digital audio  
player to the CDR 20 for digital recording.  
When an active digital signal is connected to  
both the front- and rear-panel coaxial inputs,  
the source connected to the front-panel input  
will be selected for recording.  
2 Status-Mode Indicator: When the CDR  
20 is in the ON mode, this indicator will glow  
green. When the unit has been placed in the  
Standby mode by pressing the Power-Off but-  
! Erase: Press this button to erase one or  
more tracks or the entire contents of an unfi-  
nalized CD-RW disc. When a CD-RW disc has  
already been finalized you may erase the entire  
disc or you may unfinalize” the disc by erasing  
the TOCdata. See page 22 for more informa-  
tion on erasing CD-RW discs.  
32  
ton  
on the remote, the indicator will glow  
amber, indicating that the unit is still connected  
to the AC main supply and is ready to be  
turned on from the remote control.  
7 Play-Deck Open: Press this button to  
open the Play Deck 3.  
3 Play Deck: This disc deck is used to play  
back conventional CD discs and CD-R or  
CD-RW discs that have been finalized.  
8 Record Button: Press this button to begin  
the recording process. See pages 20-22 for  
more information on CD recording.  
5 FRONT-PANEL CONTROLS  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Front-Panel Controls  
@ Finalize: Press this button when a record-  
ing is complete to initiate the finalization  
process. The Play/Select Button *j  
must be pressed within three seconds to acti-  
vate finalization. Until this button is pressed  
and the finalization process is complete, CD-R  
discs may not be played on conventional CD  
machines. See page 22 for more information on  
finalization.  
Ô Record Deck Previous: This button has  
two functions. When a disc is playing in the  
Record Deck %, press and hold this button to  
play the disc in a fast reverse mode to quickly  
locate a desired passage. At any time, tapping  
the button and quickly releasing it will move to  
the beginning of the current track, and the next  
press will move to the previous track. When a  
disc is stopped, each press will move back one  
for programming or play when the disc is  
stopped. Once a track is entered, it may be  
played by simply pressing the Play  
ˆ Play-Deck Next: When a disc is playing in  
the Play Deck 3, press and hold this button to  
play the disc in a fast-forward mode to quickly  
locate a desired passage. At any time, tapping  
the button and quickly releasing it will move to  
the next track on a disc in play.  
˜ Play-Deck Previous: This button has two  
functions. When a disc is playing in the Play  
Deck 3, press and hold this button to play the  
disc in a fast-reverse mode to quickly locate a  
desired passage. At any time, tapping the but-  
ton and quickly releasing it will move to the  
beginning of the current track, and the next  
press will move to the previous track. When a  
disc is stopped, each press will move back one  
track for programming or play when the disc is  
stopped. Once a track is entered, it may be  
played by simply pressing the Play button  
˘j.  
# Speed: Press this button to select the  
recording speed for internal dubs. See page 20  
for more information on selecting the proper  
speed.  
button *j.  
Input Select: Press this button to select  
the input source (analog or digital coax) for  
recording. See page 22 for more information on  
input selection.  
$ Record-Deck Open: Press this button to  
open the Record Deck %.  
% Record Deck: This Disc Deck is used to  
record or play back CD, CD-R and CD-RW discs.  
Ò Record-Deck Display Select: Press this  
button to cycle through the time display options  
for the Record Deck. See page 17 for more  
information on the time display.  
^ Analog-Record Level Control: The con-  
trol is used to adjust the input level when mak-  
ing recordings from analog sources such as cas-  
settes, or when CDs are recorded in an analog  
mode. See page 22 for more information on  
record levels.  
¯ Play-Deck Pause: When the Play Deck is  
running, pressing this button will pause the  
disc. If the disc has previously been paused,  
pressing this button will restart the playback.  
Ú Information Display: The indicators in  
the Information Display provide status reports  
on the operation of the CDR 20. See page 7 for  
complete explanations of each indicator.  
˘ Play-Deck Play: Press this button to begin  
playback of a CD in the Play Deck or the dub-  
bing process.  
& Record-Deck Stop: Press this button to  
stop the CD in the Record Deck.  
Û Remote Sensor: The IR sensor that  
receives the commands from the remote control  
is behind this area. Do not cover or obscure this  
part of the front panel to avoid any malfunction  
with the remote.  
¸ Play-Deck Stop: Press this button to stop  
the CD in the Play Deck.  
* Record-Deck Play/Select: This button  
has two functions. It may be pressed when a  
standard CD is in the Record Deck to put the  
machine in play, or it may be used to enter a  
selection or start certain record functions.  
Ù Play-Deck Display Select: Press this but-  
ton to cycle through the time display options  
for the Play Deck. See page 17 for more infor-  
mation on the time display.  
( Record-Deck Pause: When the Record  
Deck is in the Play mode, pressing this button  
will pause the disc. If the disc has previously  
been paused, pressing this button will restart  
the playback.  
ı Dual-Play Selector: Press this button to  
enable both CD decks to play at the same time  
and function as separate, independent CD  
units. In this mode it is also possible to record  
from an external source while the Play Deck is  
functioning as a standard CD player. See page  
17 for more information on dual-play capability.  
Ó Record-Deck Next: When a disc is play-  
ing in the Record Deck %, press and hold this  
button to play the disc in a fast-forward mode  
to quickly locate a desired passage. At any time,  
tapping the button and quickly releasing it will  
move to the next track on a disc in play.  
6 FRONT-PANEL CONTROLS  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Front-Panel Information Display  
QS  
M
U
O
Y W  
L X  
Q
O
M
S
N
V T R  
N
L
K
P
E
G
E K  
A
I
A
C
C
D
F
H J  
D
B
B
A Random Indicators  
B Program Indicators  
C Level Indicators  
D Repeat Indicators  
E Repeat-Status Indicators  
F Speed Indicators  
G Copy-Prohibit Indicator  
H Dubbing Indicator  
I Sync Indicator  
J Dual-Play Indicator  
K Information Displays  
L Time Indicators  
M Remaining-Time Indicators  
N Total-Time Indicators  
O Track-Time Indicators  
P R/RW Indicator  
S CD Indicators  
T Record Indicator  
U Finalize Indicator  
V Erase Indicator  
W Auto Indicator  
X Analog Indicator  
Y Digital Indicator  
Q Play/Pause Indicators  
R Sample-Rate Converter  
Important Note: Since the CDR 20 is a dual-deck player/recorder, there are two separate sets of indicators for the Random, Program, Repeat, Repeat  
Status, Time, Total Time and Track Time. In addition, there is a separate Information Display, Play/Pause Indicator and CD Indicator for each deck. As the  
function of these indicators is identical for both decks, they are described in this manual with a common letter. When the CDR 20 is playing or recording a  
disc, any indicators that light on the left side of the display describe the status of the Play Deck, while those that light on the right side of the display  
describe the status of the Record Deck. Depending on the activity of the unit and the settings you select, different indicators may light on the two sides at  
the same time.  
Decks. See page 20 for more information on CD  
dubbing.  
A Random Indicators: These indicators light  
when random playback has been programmed  
for one of the CD decks. See page 16 for more  
information on random play.  
E Repeat-Status Indicators: These indica-  
tors display the type of repeat function being  
used. See page 18 for more information on  
repeat status.  
I Sync Indicator: This indicator lights when  
the unit has been programmed for a CD Sync  
recording. See page 21 for more information on  
CD Sync recordings.  
B Program Indicators: These indicators  
light when one of the CD decks is being pro-  
grammed for playback options. See page 18 for  
more information on programmed play.  
F Speed Indicators: These indicators show  
which record speed has been selected for dub  
recordings. See page 20 for more information  
on record-speed selection.  
J Dual-Play Indicator: This indicator lights  
when the unit is playing in the Dual mode,  
which allows both CD decks to act as playback  
decks at the same time. See page 17 for more  
information on the dual-play mode.  
C Level Indicators: These LEDs display the  
input level during an analog recording, and the  
output level during playback. See page 22 for  
more information on record levels.  
G Copy-Prohibit Indicator: This indicator  
lights when a recording is not possible  
due to the intervention of the Serial Copy  
Management System (SCMS). See page 20 for  
more information on SCMS.  
K Information Displays: These displays  
serve two functions, showing the time displays  
for discs playing, and displaying messages  
about discs or recordings.  
D Repeat Indicators: These indicators light  
when a repeat function is being used. See page  
18 for more information on repeat play.  
H Dubbing Indicator: This indicator lights  
when a dub is in progress between the two CD  
7 FRONT-PANEL INFORMATION DISPLAY  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Front-Panel Information Display  
L Time Indicators: These indicators light in  
conjunction with one of the time indicators  
MNO to show which of the time status  
modes is active.  
R Sample-Rate Converter: This indicator  
X Analog Indicator: This indicator lights  
when an analog source is being recorded.  
See page 21 for more information on source  
selection.  
lights when the Sample-Rate Converter is in use  
to change the digital sample rate when the  
incoming signal is not the standard 44.1kHz  
used by standard CDs. This is an automatic func-  
tion and does not require any user intervention.  
M Remaining-Time Indicators: These indica-  
tors light when the Information Display K  
shows the time remaining on a disc.  
Y Digital Indicator: This indicator lights when  
a digital source is being recorded. See page 21  
for more information on source selection.  
S CD Indicators: These indicators light when  
a standard CD is playing in either deck 3 or  
%.  
N Total Time: These indicators light when the  
Information Display K shows the total time of  
all tracks on a disc.  
T Record Indicator: This indicator lights  
when the unit is making a recording and flashes  
during the preparations for recording.  
O Track Time: These indicators light when the  
Information Display K shows the running time  
of the individual track being played.  
U Finalize Indicator: This indicator lights  
when the unit is in the Finalization process,  
which is required before a CD-R disc may be  
played on a standard CD machine. See page 22  
for more information on Finalization.  
P R/RW Indicator: This indicator shows which  
type of recordable disc is present in the Record  
Deck %. When a CD-R disc is present, only the  
R is lit. The RW lights when an erasable CD-RW  
disc is in use.  
V Erase Indicator: This indicator lights when  
a CD-RW disc is being erased. Note that only  
CD-RW discs may be erased; it is not possible to  
erase a CD-R disc. See page 22 for more infor-  
mation on erasing discs.  
Q Play/Pause Indicators: These indicators  
show the status of the individual CD decks. The  
lights when the CD is playing, and the ›  
±
lights when the unit is in a Pause mode.  
W Auto Indicator: This indicator lights when  
the automatic method of incrementing tracks is  
selected for a recording session. See page 21 for  
more information on track increments.  
8 FRONT-PANEL INFORMATION DISPLAY  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Rear-Panel Connections  
AC 100~240V 50-60Hz 28W  
OPTICAL  
CDR  
IN  
CDP  
OUT  
ª
¡
£
§
¢
¡ Play Deck (CDP) Analog Output  
Record Deck (CDR) Analog Output  
£ Record Deck (CDR) Analog Input  
¢ Play Deck (CDP) Coaxial-Digital Output  
Record Deck (CDR) Coaxial-Digital Output  
§ Record Deck (CDR) Coaxial-Digital Input  
Record Deck (CDR) Optical-Digital Input  
Play Deck (CDP) Optical-Digital Output  
ª Remote IR Input  
Remote IR Output  
AC Power Cord  
IMPORTANT NOTE: The coaxial digital inputs  
should only be connected to digital input or  
output jacks. Even though they use the same  
RCA type connector as standard analog audio  
connections, DO NOT connect them to conven-  
tional analog input or output jacks.  
CDR 20 provide IR signals to other compatible  
products.  
¡ Play Deck (CDP) Analog Output: These  
jacks carry the analog audio output signal from  
the Play Deck 3. Connect them to the CD  
input jacks on a receiver, preamp or processor.  
AC Power Cord: Connect this plug to an  
AC outlet. If the outlet is switch controlled,  
make certain that it is in the ON position.  
Record Deck (CDR) Analog Output:  
These jacks carry the output signal from the  
Record Deck %. Connect them to the Tape  
Play/In input jacks on a receiver, preamp or  
processor.  
Record Deck (CDR) Optical-Digital  
Input: This jack accepts the digital-audio input  
signal from a compatible digital audio product,  
and should be connected to the optical-digital  
output on a CD or DVD player or an A/V  
receiver or processor.  
£ Record Deck (CDR) Analog Input: These  
jacks accept the analog signals that are used  
for CD recordings. Connect them to the Tape  
Rec/Play outputs on a receiver, preamp or  
processor.  
Play Deck (CDP) Optical-Digital  
Output: This jack carries the optical digital  
output signal from the Play Deck 3. Connect  
it to an optical digital input on a receiver,  
processor or digital recorder. This will typically  
be connected to the “CD” input.  
¢ Play Deck (CDP) Coaxial-Digital  
Output: This jack carries the digital-audio out-  
put signal from the Play Deck 3. Connect it  
to a coaxial-digital input on a receiver, proces-  
sor or digital decoder.  
ª Remote IR Input: Connect the output of a  
remote infrared sensor or the remote control  
output of another compatible Harman Kardon  
product to this jack. This will enable the remote  
control to operate even when the front-panel  
Remote Sensor Û is blocked. This jack may  
also be used with compatible IR remote control  
based automation systems.  
Record Deck (CDR) Coaxial-Digital  
Output: This jack carries the digital audio out-  
put signal from the Record Deck %. Connect  
it to a coaxial digital input on a receiver,  
processor or digital decoder.  
§ Record Deck (CDR) Coaxial-Digital  
Input: This jack accepts the digital-audio input  
signal from a compatible digital audio product  
and should be connected directly to a digital  
player or to a coaxial-digital output on a CD or  
DVD player or an A/V receiver or processor.  
Remote IR Output: Connect this jack  
to the IR input jack of another compatible  
Harman Kardon remote controlled product to  
have the built-in remote sensor Û on the  
9 REAR-PANEL CONNECTIONS  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote Control Functions  
a Power-On Button  
b Play Deck (CDP) Display Control  
c Play Deck (CDP) Open  
d Play Deck (CDP) Select  
e Program  
f Reverse Search  
g Single  
h Program Check  
i Previous-Track Skip  
j Play/Select  
k Random Play  
l Dub  
m Automatic/Manual Track Increment Selector  
n Track Increment  
o Finalize  
p Numeric Keys  
q A-B Repeat  
r Repeat  
POWER  
33  
31  
OFF  
ON  
a
32  
30  
CLEAR  
b
c
e
PROG.  
d
f
29  
SEARCH  
SEARCH  
28  
SINGLE  
DUAL  
PROG  
CHECK  
`
g
h
j
PREV  
NEXT  
PLAY/SELECT  
z
i
k
STOP  
PAUSE  
s Speed Select  
t Record Button  
u Erase Button  
v Input Select  
w CD Sync  
x Stop  
y Pause  
z Next Track/Skip  
` Dual-Deck Playback  
RANDOM  
y
w
x
v
t
l
n
m
o
Forward Search  
28  
29  
Record Deck (CDR) Select  
Record Deck (CDR) Open  
Record Deck (CDR) Display Control  
Power Off  
u
s
30  
SPEED  
31  
1
4
7
2
5
8
0
3
6
9
32  
Clear  
33  
34  
p
IMPORTANT NOTE: Some of the remotes  
functions, including Play, Pause, Stop,  
Search, Next and Previous Track, are  
shared between the two decks. Always  
remember to press the CDP Select button  
d to use the remote to control the Play  
REPEAT  
r
A
B
q
29  
Deck, or press the CDR Select button  
to control the Record Deck. When you  
press one of these buttons, an indication  
of CDPor CDRwill appear in the appro-  
priate Information Display K.  
CDR/RW  
10 REMOTE CONTROL FUNCTIONS  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote Control Functions  
a Power-On Button: Press this button to  
turn the CDR 20 on. Note that in order for this  
control to function, the Front-Panel Power  
Switch 1 must first be pressed so that the  
unit is in the Standby mode.  
l Dub: Press this button to begin a dub. See  
page 20 for more information on dubbing.  
w CD Sync: Press this button once to begin  
an automated recording of a single track from  
an external CD player when a digital connection  
is used. Press it twice to begin automated  
recording of an entire disc. See page 21 for  
more information on CD Sync recording.  
m Automatic/Manual Track Increment  
Selector: Press this button to select between  
automatic and manual track increments during  
a recording session. See page 21 for more infor-  
mation on track increments.  
b Play Deck (CDP) Display Control: Press  
this button to cycle through the various time  
display options for the disc in the Play Deck  
3. See page 17 for more information on time-  
display options.  
x Stop: Press this button to stop playback or  
recording.  
n Track Increment: When the Manual  
mode for track increments is selected during  
recording, press this button to increase the  
track number. NOTE: This function does not  
operate during CD Sync or dub recording.  
y Pause: Press this button to momentarily  
pause playback. Press it again to resume  
playback.  
c Play Deck (CDP) Open: Press this button  
to open the Play Deck 3.  
z Next Track/Skip: Press this button to skip  
d Play Deck (CDP) Select: Press this but-  
ton to control or program the functions of the  
disc in the Play Deck 3.  
o Finalize: Press this button when a record-  
ing is complete to initiate the finalization  
process. The Play/Select button *j must  
be pressed within three seconds to activate  
finalization. Until this button is pressed and the  
finalization process is complete, CD-R or CD-RW  
discs may not be played on conventional CD  
machines. See page 22 for more information  
on Finalization.  
forward to the next track on a disc.  
` Dual Deck Playback: Press this button  
to enable both CD decks to play back at the  
same time and function as separate, independ-  
ent CD units. In this mode it is also possible to  
record from an external source while the Play  
Deck is functioning as a standard CD player. See  
page 17 for more information on dual-play  
capability.  
e Program: Press this button to begin the  
programming sequence for one of the CD  
decks. See page 18 for more information on  
programming the CDR 20.  
f Reverse Search: Press this button to play  
the selected disc in reverse to locate a desired  
passage.  
p Numeric Keys: Press these buttons to  
access a specific track for playback or during  
the programming process. See page 18 for more  
information on programmed playback.  
28  
Forward Search: Press this button to  
play a disc in a fast-forward mode.  
g Single: When this button is pressed, the  
CDR 20 will function as a two-disc CD player/  
changer. In the Single mode, the audio output  
will be routed to all output jacks ¡™¢∞  
regardless of which CD deck is actually  
playing. See page 17 for more information on  
the Single-Play mode.  
29  
Record Deck (CDR) Select: Press this  
button to control or program the functions of  
the disc in the Record Deck %.  
q A-B Repeat: Press this button to specify a  
segment of a disc for repeat play. See page 18  
for more information on repeat play.  
30  
Record Deck (CDR) Open: Press this  
button to open the Record Deck %.  
r Repeat: Press this button once to repeat  
the current track. To repeat an entire disc, press  
the button twice.  
31  
Record Deck (CDR) Display Control:  
h Program Check: Press this button to  
check or edit a programmed playback sequence.  
See page 18 for more information on pro-  
grammed playback.  
Press this button to cycle through the various  
time-display options for the disc in the Record  
Deck %. See page 17 for more information on  
time-display options.  
s Speed Select: Press this button to select  
the recording speed for internal dubs. See page  
20 for more information on selecting the proper  
speed.  
i Previous-Track Skip: Press this button to  
skip backwards to the beginning of the track  
currently being played. Press it a second time to  
move back to the beginning of each previous  
track.  
32  
Power-Off: Press this button to place the  
unit in a Standby mode.  
t Record Button: Press this button to  
begin a manual recording.  
33 Clear: Press this button to clear an item  
in a program sequence. See page 18 for more  
information.  
u Erase Button: Press this button to initiate  
the erasure of a track or of an entire CD-RW  
disc or to Unfinalize a disc. Note that erasure is  
only possible on CD-RW discs. See page 22 for  
more information on erasing discs.  
j Play/Select: This button has two func-  
tions. It will most often be used as a standard  
play button, but when setting up certain record  
functions, it is also used as an Enter or Select  
button.  
v Input Select: Press this button to select  
the input source (analog or digital-coax) for  
recording. See page 21 for more information on  
input selection.  
k Random Play: When the CD deck is  
stopped, press this button to begin random play  
of all tracks on a disc.  
11 REMOTE CONTROL FUNCTIONS  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation and Connections  
Important Note: To prevent possible damage  
to your speakers or other components in your  
audio system, we strongly recommend that ALL  
system components, including the CDR 20, be  
turned off and unplugged from their AC power  
source when any connections are made or a  
new component is installed.  
Play-Deck Connections  
To make recordings from external digital  
sources, such as a CD, DVD or MD player, con-  
nect the CDR Coax-In jacks §6 or CDR  
Optical In Jack on the CDR to the digital  
output jacks on your receiver or processor. If  
your receiver does not have digital-output jacks,  
you may connect the CDR Coax In jacks  
§6 or CDR Optical In Jack on the CDR  
20 directly to the digital outputs on your CD  
player or other digital device.  
The rear-panel connections labeled “CDP” refer  
to the outputs of the Play Deck 3, which  
functions as a standard CD player. Connect the  
analog left/right CDP outputs ¡ to the CD  
inputs on your receiver, preamp or surround  
processor. For best playback results, a digital  
connection is recommended, using the coaxial  
or optical ¢• outputs. Connect them to the  
matching digital inputs of your receiver, pre-  
amp, processor or external digital decoder. Note  
that you may have to change a setting on the  
receiver or processor to link the digital input to  
the “CD” button or input selector. Consult the  
owners manual on that device for details, as  
this configuration may vary from unit to unit.  
Locating the CDR 20  
Since the CD transports in the CDR 20 are pre-  
cision instruments, they are subject to interfer-  
ence from vibration. To minimize the possibility  
of skipping during playback or recording, it is  
recommended that the unit be placed on a  
level, solid, vibration-free surface.  
Connections to a portable digital CD or MD  
player may also be made by connecting the  
Coax Digital Output of the player to the Front-  
Panel Digital Input 6 on the CDR 20.  
Note that when both the front and rear panel  
digital inputs are connected to external sources,  
the CDR 20 will give priority to the front-panel  
input 6. If it is impractical to disconnect the  
front-panel input when you need to use the  
rear-panel jack, simply turn off the device con-  
nected to the front-panel input. This will stop  
the digital signal, and permit the rear-panel  
jack to be used.  
When installing the CDR 20 in a cabinet or  
tight space, always make certain that there is  
enough room in front of the unit for the disc  
drawers to open fully, and that there is enough  
space above the unit so that discs may easily  
be inserted in the disc drawers.  
Record-Deck Connections  
The rear-panel connections labeled “CDR” refer  
to the inputs and outputs for the Record Deck  
%. Depending on the capabilities of your  
receiver, preamp or processor, you may find it  
convenient to connect the analog inputs and  
outputs to the jacks marked for a tape recorder.  
As the CDR 20s functions resemble those of  
a standard tape recorder, this might make it  
easier to select it as an input on your receiver  
or preamp. Connect the analog CDR-Out jacks  
to the Play/In jacks of a Tape or Aux input  
on your receiver or preamp. Connect the CDR-In  
jacks £ to the Tape Rec/Out jacks on your  
receiver or preamp.  
In addition to the safety considerations outlined  
on page 4, it is also recommended that the  
CDR 20 not be placed in a location that is sub-  
ject to direct sunlight or extreme heat or cold,  
as these conditions may damage the discs used  
in the player, or the player itself. Note that  
audio amplifiers or high-power receivers, as  
well as certain other electronic products, may  
generate significant heat. For that reason, do  
not place the CDR 20 directly on top of an  
amplifier, receiver, or other heat source. Always  
allow at least one inch of free space on all  
sides of the CDR 20, as well as other electronic  
products, to allow for proper ventilation.  
IMPORTANT NOTES ON DIGITAL  
CONNECTIONS:  
Although digital-coax connections use the same  
type of “RCAphono jack as standard analog  
signals, please take special care to connect digi-  
tal signals only to digital jacks. In many cases,  
the digital jacks may be identified by an  
orange-colored insert ring around the center of  
the jack. When making digital connections, be  
sure to use coax-interconnect cables, such as  
the one supplied with the CDR 20 or cables  
intended for video applications. Even though  
they have the correct type of RCA connector, do  
not use audio-interconnect cables that have  
twisted-pair construction, as they are not  
appropriate for digital signal use. If you have  
any questions about the type of cables to use  
with the CDR 20, consult your dealer.  
To play the output of the Record Deck through  
the digital decoder in your receiver or an exter-  
nal processor, connect the CDR Coax-Out ∞  
jacks to the matching digital-input jacks on  
your receiver or processor. Note that you may  
have to change a setting on the receiver or  
processor to link the digital input to the “Tape”  
button or the specific input selector associated  
with the digital inputs. Consult the owners  
manual on your receiver or processor for  
details, as this configuration may vary from unit  
to unit.  
The unit should also be kept away from sources  
of water or damp conditions.  
Connections to Your Audio System  
When connecting the CDR 20, think of the  
process as if your were connecting a standard  
CD player and a tape or cassette recorder, with  
the addition of the digital connections.  
12 INSTALLATION AND CONNECTIONS  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation and Connections  
Batteries  
IR Remote Connections  
Insert the two AA batteries supplied with the  
CDR 20s remote by turning the remote over so  
that the bottom of the remote is facing towards  
you. Gently lift the plastic tab on the battery  
cover up and away from you, and lift the lid off.  
Insert the batteries in the remote, being careful  
to follow the + and – polarity indications in the  
bottom of the compartment. Replace the cover  
by first seating the two small tabs into the mat-  
ing holes at the top of the remote, and then  
gently push the cover down until the latch  
snaps into place with an audible click.  
If the CDR 20 is installed behind a cabinet or  
other obstruction that may block the path  
between the front-panel Remote Sensor Û  
and the location where you will use the remote,  
an optional external IR sensor may be used.  
Connect the sensor to the Remote IR In Jack  
ª on the rear-panel. This jack may also be  
connected to the IR Output jack of another  
compatible Harman Kardon component or a  
compatible IR system remote product.  
You may also use the IR Sensor in the CDR 20  
to send commands to other compatible remote  
products. Connect the Remote IR Out Jack  
to the input of the other product or system.  
Power Connections  
Connect the AC Power Cord to an AC  
power source. the CDR 20 uses sensitive, high-  
performance computer-grade CD drives, and to  
protect them we recommend that you consider  
the use of a surge protector, just as you would  
for a computer.  
If the rear-panel AC outlet on a receiver or  
other product is used, make certain that it  
provides at least 28 watts, and that the total  
power of all products connected does not  
exceed the maximum rated output of the prod-  
uct containing the outlets. If the CDR 20 is con-  
nected to a switched outlet, remember to turn  
on the outlet or product controlling it in order  
for the CDR 20 to operate.  
NOTE: When replacing batteries, it always a  
good idea to replace both at the same time.  
When the remote will not be used for an  
extended period of time, it is also a good idea  
to remove the batteries to avoid the possibility  
of damage due to corrosion. Batteries contain  
chemical substances and we recommend that  
you dispose of them properly and in compliance  
with any local regulations.  
13 INSTALLATION AND CONNECTIONS  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CD Recording Basics  
CD Recorders (CDRs) are similar to standard CD  
players, with the addition of the features and  
controls needed for recording. Functions such  
as play, search and programming for playback  
will be familiar, but the recorder will function  
slightly differently than what you may be used  
to for magnetic tape recorders.  
TOC: Stands for Table of Contents and it  
refers to the data recorded on each CD that  
tells the player how many tracks are on the  
disc, the total time of the disc and the running  
time of each individual track. Each time a disc  
of any sort is placed in the CDR 20, you will see  
a TOCto indicate that the unit is reading this  
data from the disc. This is required to copy the  
track information to any recording.  
R e c o r d a b le  
Re W r it a ble  
Discs designed for use in  
computer CD-R drives may not be used for  
recording in the CDR 20. Only discs specifically  
designed for use in consumer CD audio  
recorders may be used. If you attempt to  
use a blank-computer-type recordable disc for  
recording on the CDR 20 you will see a  
NOAUDIOmessage in the Information  
Display K and recording will not be possible.  
However, discs that have been recorded in the  
CD-R drive of a computer may be played in the  
CDR 20, provided that they have been properly  
finalized in accordance with audio standard  
IEC958.  
Disc Types  
Unlike a conventional CD player, the CDR 20  
uses three types of discs, and it is important to  
understand how each one plays.  
OPC: Stands for Optical Processing  
Calibration. When you see this message in the  
Information Display for the Record Deck  
K, it means that the laser transport inside the  
unit is making the calibrations and adjustments  
needed so that the recording process is  
optimized for the specific disc in use.  
Both decks in the CDR 20 will play  
back any conventional CD that bears this logo.  
Note that the CDR 20 is specifically designed  
for the recording and playback of consumer  
audio discs, and cannot be used to copy data  
discs, DVD discs, or other optical discs used by  
video- or computer-game systems.  
BUSY: When you see this message, it means  
that the Record Deck is completing part of the  
record operation. When you see this message,  
do not press any buttons; simply wait until the  
message clears from the display.  
R e c o r d a b le  
Discs that bear this logo may be  
recorded on one time, and when they are final-  
ized they will play in either deck in the CDR 20  
or in any conventional CD player, including  
home, car and portable models. The Record  
Deck % on the CDR 20 may also be used  
to record on these discs, and it will play  
CD-R/Audio discs even if they have not been  
finalized.  
CDR Terminology and Display Messages  
Compact disc recording has its own special  
terminology, and some of the messages  
displayed by the CDR 20 may be new to you.  
Before using the CDR 20, you may wish to  
familiarize yourself with some of the terms used  
by the CDR 20. Additional error message dis-  
plays may also appear. Please see page 23 for a  
complete explanation of error messages.  
DISC FULL: When there are only four  
seconds of record time remaining on a blank  
disc, a DISC FULLmessage will appear  
in the Information Display ˚. When you  
see this message, you will need to stop the  
recording process and, when a CD-R is being  
recorded, insert a new blank disc or, when a  
CD-RW is in use, either use a new disc or erase  
existing tracks following the instructions on  
page 22.  
Re W r it a ble  
Discs that bear this logo may be used  
Finalize: This term refers to the process  
that completes the recording of a disc by  
recording a final Table of Contents and prepar-  
ing the disc so that it may be played on other  
machines. A CD-R disc may not be played on  
other CD players until it is finalized. However,  
once the finalization process is complete, a  
CD-R disc may not be recorded on again. Only  
CD-RW discs may be “Unfinalized,” so that  
additional tracks may be recorded on a disc.  
for recording on the CDR 20, and they may also  
be erased and reused. They may be recorded on  
or played on the Record Deck % of the  
CDR 20 and in other CD-RW recorders or  
CD-RW compatible players. They will NOT play  
back in most current CD players unless the  
player is CD-RW compatible. CD-RW Audio  
discs will play on most DVD players once they  
have been finalized.  
14 CD RECORDING BASICS  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Playback Basics  
Playback of CDs on the CDR 20 resembles that  
for traditional CD players with a few exceptions  
to accommodate the availability of two sepa-  
rate playback decks. Before using the CDR 20,  
power-up the unit by pressing in the Main  
Power Switch 1. Note that the Status-  
Mode Indicator 2 will turn green, indicating  
that the unit is on and functioning. At the same  
time, the Information Display Ú will illuminate  
and the legends behind the front-panel controls  
will also light up.  
Load a disc in the tray with the printed (label)  
side facing up. Once the disc is seated, make  
certain that it is properly centered within the  
tray. When using 3" discs, take extra care to  
make certain that the disc is carefully centered  
within the smaller ridges in the disc tray.  
Using the Remote  
The CDR 20s infrared remote control is  
designed to operate both CD decks, as well as  
control the playback programming and record  
functions. To allow for efficient use of the  
remote, its operation is different from standard  
CD players. Some buttons are dedicated to one  
specific CD deck, while others are shared  
between the two decks.  
No matter which deck is playing, the Play  
Deck (CDP) and Record Deck (CDR)  
31  
and Open/Close buttons  
will always send a command to their  
Once the Main Power Switch 1 has been  
turned on, the CDR 20 may be powered-on  
or -off using the remote control. Pressing the  
Display b  
c
30  
respective deck. The other transport and pro-  
gramming functions, however, are shared. To  
use any of the transport controls, such as Play  
j, Stop x, Pause y or the Search  
32  
Power-Off button  
on the remote will  
Labeled  
Surface  
place the unit in a Standby mode, as indicated  
by the amber color of the Status-Mode  
Indicator 2. To turn the unit on using  
the remote, simply press the Power-On  
button a.  
28  
, the  
To close the drawer, press the appropriate  
and Skip buttons fiz  
Open/Close button 7$c  
or gently  
Numeric Keys p or the Programming  
Keys eghkr, first press either the  
CDP button d to command the Play Deck  
30  
press on the outside of the front cover of the  
disc tray. When the drawer is closed the word  
CLOSEwill appear momentarily in the  
Information Display K, and the letters  
TOCwill begin to flash in the display once the  
drawer is completely closed.  
29  
to command the  
Note that when the unit is in the Standby mode,  
it is still drawing power from the AC main  
outlets. To turn the unit completely off, press  
the Main Power Switch 1. When the  
Status-Mode Indicator 2 goes out, the  
CDR 20 is off and not drawing any power.  
When you will not be using the unit for an  
extended period of time, such as during a  
vacation, we recommend using the Main  
Power Switch 1 to turn the unit  
3 or the CDR button  
Record Deck %. When the button is pressed,  
a message reading CDP or CDR will appear in  
the appropriate Information Display K to  
confirm the selection.  
If the disc is a standard CD or a finalized CD-R  
or CD-RW disc, TOCwill flash while the unit  
reads the discs Table of Contents information.  
Once that data is read, the Information  
Display K will show the total number of  
tracks and the total time of all tracks on the  
disc. The CD Indicator S will also light to  
indicate that a standard CD is in use.  
To switch the remote from controlling one deck  
to controlling the other, simply press the Select  
29  
button d  
trol at any time.  
for the deck you wish to con-  
completely off.  
Note that features relating to the recording  
process, such as Speed s and the double  
row of record-function buttons in the center of  
the remote lmnotuvw  
and the Single/Dual buttons g` are  
dedicated feature buttons that do not require  
any special selection.  
Although compact discs are very reliable, rough  
handling may damage them. Avoid scratching  
the bottom (nonprinted) side of the discs, as  
this will affect playback of standard CDs and  
interfere with the recording of CD-R and  
CD-RW discs. It is also a good idea to always  
handle discs by their edges to avoid fingerprints  
which may also interfere with playback quality  
and possibly cause damage to the laser and  
lens assembly.  
When an unfinalized CD-R or CD-RW disc is  
placed in the Record Deck %, the letters  
OPCwill flash once the Table of Contents has  
been read. This indicates that the unit is opti-  
mizing its circuits for maximum compatibility  
with the specific recordable disc in use. The  
number and total running time of any tracks  
that have already been recorded will appear in  
the Information Display K, and the appro-  
priate indicator SP will light to tell you if a  
CD-R or CD-RW disc is in use.  
Loading and Unloading Discs  
To load a disc, first open the desired CD deck  
by pressing the appropriate Open/Close  
button 7$c  
. The word OPENwill  
If a computer data disc is placed in the CDR 20,  
a DATADISCor DISCERRORmes-  
sage will appear, depending on whether or not  
the data disc is finalized. Data discs will not  
play and cannot be recorded or dubbed on the  
CDR 20.  
30  
appear in the Information Display K.  
Always make certain that there is sufficient  
room in front of the unit for the disc drawers to  
open. Note that if either disc drawer is blocked,  
the drawer will stop at the blocked position and  
an ERRORmessage will appear. Press the  
appropriate Open/Close button 7$c  
to reopen the drawer.  
30  
15 PLAYBACK BASICS  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Playback Basics  
Normal Play  
To momentarily stop the disc at any time, press  
the Pause button y(¯. When a disc is  
paused, the Play/Pause Indicator Q will add  
two vertical lines to indicate a paused disc.  
Press either the Play button j*˘ or the  
Pause button y(¯ to resume playback  
at the point where the disc was paused.  
Search  
To play a disc, first make certain that the unit is  
properly installed and that the Main Power  
Switch 1 is turned on. Turn the CDR 20 on  
by pressing the Power-On button a on the  
remote and note that the front-panel display  
will illuminate.  
You may quickly scan through the contents of a  
disc while listening to the playback at high  
speed in forward or reverse. To move forward  
through a disc, press the Forward Search but-  
28  
ton  
on the remote or press and hold the  
Next button Óˆ on the front panel that is  
appropriate for the deck in use. To move back-  
wards through a disc, press the Reverse  
Search button f on the remote, or press  
and hold the Previous button Ô˜ on the  
front panel that is appropriate for the deck in  
use. When using the remote, always remember  
to make certain that you have selected the deck  
you wish to control by pressing the appropriate  
selector button d 29 before entering the  
desired remote command.  
Insert a disc following the instructions shown  
on the previous page. To start the playback,  
press the Play button on the front panel for the  
appropriate deck or press the Select but-  
ton on the remote for the desired deck d  
29 and then press the Play button on the  
remote j. The Play/Pause Indicator Q  
will show a right pointing triangle and the  
Information Display K will show the track  
number being played and the running time of  
the track. As each new track begins to play, the  
track time will reset to 00:00and begin to  
count up for the new track.  
When there is only one disc in the unit, it will  
automatically stop when all tracks on a disc  
have played through. To stop playback at any  
time, press the Stop button x&¸ for the  
deck in use.  
When there is a disc in each deck, the player  
will respond in one of two ways, depending on  
which way the dual-play setting is activated. In  
normal operation, when the disc in one drawer  
finishes, the disc in the other drawer will begin  
to play. When the Dual button is  
pressed so that the Dual-Play Indicator J is  
lit, each deck will operate as a separate, single-  
play CD unit without regard to the status of the  
other deck. For complete information on Dual-  
Deck and Dual-Play operation, see page 17.  
Track Skip  
To move from one track on a disc directly to  
another, enter the number for the desired track  
with the Numeric Keys p. The disc will  
pause briefly to locate the track, and then  
immediately play it. When entering a two digit  
track number, the second digit must be entered  
within three seconds of the first digit.  
NOTE: Remember that Unfinalized CD-R or  
CD-RW discs will only play in the Record  
Deck %. If you attempt to play an Unfinalized  
disc in the Play Deck 3, a DISC  
ERRORmessage will appear to remind you  
to play the disc in the other deck.  
At the end of a listening session, remove the  
discs from the decks by following the instruc-  
tions shown on the previous page. Do not leave  
the disc drawers open when the unit is not  
in use to prevent dust and dirt from entering  
the unit and to prevent damage to the disc-  
drawer tray.  
To move to the next track on a disc by cycling  
through the individual tracks, press the Next  
button z on the remote, or the appropriate  
front-panel Next button Óˆ for the deck in  
use. Additional presses of the button will move  
forward through the tracks on the disc.  
To go directly to a specific track on a disk, enter  
the track number using the Numeric Keys  
p. Note that when selecting a two digit track  
number, the second digit must be entered with-  
in three seconds after the first Numeric Key is  
pressed.  
To place the unit in the Standbymode at  
the end of a listening session, press the Power-  
When a disc is playing, press the Previous  
button iÔ˜ to return to the beginning of  
the track being played. Additional presses of  
the Previous button will move backwards  
through the tracks on the disc.  
To play all of the tracks on a disc in random  
order, press the Select Button d 29 for  
the desired deck, and then press the Random  
button k. The unit will briefly examine all  
of the tracks on the disc and the Random  
Indicator A will illuminate. Each track will be  
played in a random order until all tracks on the  
disc have been played. Note that there will be a  
brief pause in between each track as the unit  
searches for the next track to play. During  
the search, the left two positions in the  
Off button  
. The word OFFwill appear  
32  
briefly in the Information Display K, any  
open disc trays will automatically close, and the  
Status-Mode Indicator 2 will turn amber.  
When a disc is stopped, you may press the Next  
or Previous buttons to locate a specific track  
that you wish to play. When the desired track  
number appears at the left side of the appropri-  
ate Information Display K, press the Play  
button j*˘ to hear that track.  
Information Display K will show a clock-  
wise circle to confirm the search.  
16 PLAYBACK BASICS  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Playback Basics  
Dual-Play Mode  
Dual-Deck Operation  
To view the total time remaining on the disc,  
31  
ÒÙ for  
Since the CDR 20 has more than one CD deck,  
you may play a disc in either drawer. When only  
one deck is playing, the unit is in the Single  
mode. In the Single mode, the audio output will  
be fed to all digital and analog jacks for both  
decks. This means you may select the input on  
your receiver, preamp or processor for either  
deck. For example, if you have the Play Deck  
connected to “CD” and the Record Deck con-  
nected to “Tape,” when only one deck is play-  
ing, either input may be selected.  
Since the CDR 20 has two separate CD decks, it  
may be used as a two-disc changer, so that you  
can continually play two discs.  
press the Display Button b  
the deck in use so that the Total Time  
Indicators NL illuminate. The Information  
Display K will show the total time remaining  
for all tracks on the disc and count down until  
the disc has finished playing. When the disc has  
played all the way through, the total number of  
tracks and the total running time of the disc  
will be displayed.  
When the CDR 20 is in the Single-Play mode,  
as shown by the Dual-Play Indicator J  
NOT being lit, when the disc in one deck has  
played through to the end, the disc in the other  
deck will automatically begin to play. Each disc  
will play through, and when one deck is fin-  
ished the other will start. To stop playback,  
press the Stop button x&¸ for the deck  
that is currently playing.  
Headphone Listening  
You may listen to the output of the CDR 20  
through headphones at any time by simply  
plugging the headphones into the Front-Panel  
Jack 4. The volume of the headphone output  
may be adjusted with the Headphones Level  
Control 5. Note that changes to the head-  
phone level will not alter the output settings to  
the analog outputs. Those levels are fixed, and  
the volume should be adjusted using your  
receiver, preamp or processor.  
It is also possible to play two discs at once,  
using the Dual mode. To initiate dual-mode  
playback, press the Dual button on the front  
panel or remote ı`. When the Dual-Play  
Indicator J is lit, you may play a different  
disc in both decks at the same time. The output  
of each deck will be sent to the appropriate  
output jacks, and you will need to select the  
deck you wish to listen to using the input selec-  
tors on your receiver, preamp or processor. You  
may also use the output of one deck to feed  
your main-room system, while the second deck  
is used to feed a remote room.  
To have the CDR 20 function as two separate  
CD players, where the deck in use stops at the  
end of a disc, press the Dual button `ı  
until the Dual-Play Indicator J lights. In the  
Dual mode, each deck acts independently of the  
other and when the disc in one deck finishes, it  
stops unless one of the Repeat functions has  
been activated.  
Note that when only one deck is playing back a  
disc in the Single-Play mode, the output of that  
deck will be fed to the headphone jack. When  
the unit is in the Dual-Playback mode, only the  
output of the Play Deck 3 will be fed to the  
headphone jack.  
Time Display  
The CDR 20s time display is capable of show-  
ing a wide range of information about the con-  
tents of a CD.  
As long as the Dual-Play Indicator J is lit,  
each deck functions as a separate CD player,  
and will respond to its own set of controls on  
the front panel for either the Play Deck  
Ùˆ˜¯˘¸ or Record Deck  
&*(ÓÔÒ. To control the transports  
using the remote, remember to first press the  
Selector button for either the Play/CDP Deck  
d or the Record/CDR Deck 29 , and then  
press the desired command function.  
Once the discs Table of Contents or TOC data  
has been read, the Information Display K  
for any deck that has a CD inside will show the  
number of tracks on the disc in the two left  
digits of the display, and the total running time  
of the disc. When the disc is playing, the tracks  
will count up as each new track is reached, and  
time display will show the elapsed time for the  
track being played.  
NOTE: When in the Dual mode, you may return  
to Single play mode by pressing the Single  
button on the remote g or the Dual button  
ı on the front panel. However, pressing the  
Single button while both decks are playing,  
will automatically stop playback of the disc in  
the Record Deck % while the disc in the  
Play Deck 3 continues to play. The output of  
the play deck will be sent to both sets of out-  
put jacks.  
To view the time remaining in the track being  
played, press the Display button b  
ÒÙ for the deck in use so that the  
31  
REMAINING TIMEIndicators ML  
illuminate. The Information Display K will  
count down the time remaining in the track,  
and at the start of the next track the counter  
will start to count down the running time of  
that track.  
17 PLAYBACK BASICS  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Program Play  
The CDR 20s advanced programming system  
enables you to program the order in which  
tracks are played, to repeat one track or all  
tracks, or to repeat any segment of a disc  
without regard to track numbers.  
sion is complete. You may add up to 20 tracks,  
repeating a track if desired, as long as the total  
number does not exceed 20. If you exceed the  
20 track limit, the display will read FULL.  
Tracks may also be added using the Next  
zÓˆ and Previous buttons iÔ˜ to  
locate the track, and the Program button e  
to enter that track to the programmed  
sequence.  
in any order; as long as you have located a step  
in the program list, it may be erased.  
To cancel an entire program list while the pro-  
gram is playing, press the Program button  
e and note that the Program Indicator B  
will go out. To remove a total program list  
when the disc is stopped, simply open and  
close the disc drawer. Whenever a disc is  
removed or the unit is turned off, the program  
list is erased.  
Programming Play Lists  
To program the order of playback for the tracks  
on a disc, insert the disc, let the unit read the  
Table of Contents information, and wait until  
the disc has stopped and the number of tracks  
and total running time is displayed. Next, select  
the deck that will be programmed by pressing  
the CDP Select button d on the remote for  
the Play Deck 3 or the CDR Select button  
When the complete list of tracks has been  
entered, press the Play button j*˘.  
The tracks will then play in the order they have  
been entered. Note that a programmed list of  
tracks may also be recorded if the disc being  
programmed is in the Play Deck 3. Follow  
the instructions on page 20 for complete  
information on recording and dubbing.  
Repeat Programmed Play  
The CDR 20s programming system enables you  
to repeat either a single track on a disc, the  
entire disc, or a specially programmed passage  
that you select.  
29  
on the remote for the Record Deck %.  
To begin the programming sequence, press  
the Program button e and note that the  
PROGIndicator B will illuminate and  
the Information Display K will show  
0000: 00.  
Repeat One Track  
Checking, Editing and Clearing  
Programmed Play Lists  
To repeat the track you are currently listening  
to, press the Repeat button r and note that  
the Repeat Indicator D and the Repeat-  
Status Indicator E will both light 1. If the  
track is changed by using the Next/Previous  
Skip button izÓÔˆ˜ while the  
Repeat 1 mode is active, the new track will  
now be repeated.  
Once you have entered a program list it will  
remain in the units memory until the disc is  
removed or the unit is turned off. Thus, if you  
play through a program list, simply press the  
Play button j*˘ again to replay the list.  
If you find that you wish to check the list or  
make changes, that is also possible by following  
a few simple steps.  
Next, enter the track numbers to be played by  
pressing the Numeric Keys p. For two-digit  
track numbers, be certain to enter the second  
digit within three seconds after the first number  
is entered. As each track is entered, the display  
will blink three times, alternating between two  
displays. The first display will show the track  
number just entered on the left side of the  
Information Display K under the Track  
Indicator O, while the right side will flash  
the number of steps that have been pro-  
grammed. For example, after programming the  
first step to be track number 3, the display will  
flash 03P-01.  
Once Repeat 1 playback has been started, it  
will continue until the unit is stopped by press-  
ing the Stop button x&¸, or the disc  
deck is opened by pressing the appropriate  
To scroll through a program list, press the  
Program Check button h. Each press of the  
button will move through the tracks that have  
been programmed. The display will alternate  
between the track number of the program step  
number (e.g., 12P-03tells you that track  
12 on the disc is the 3rd program step) and the  
track number and the total running time so far  
in the program (e.g., 1216:04tells you  
that at this point you have programmed a total  
of 16 minutes and 4 seconds of material).  
Open/Close button 7$c  
. When  
30  
playback is stopped, the Repeat sequence is  
erased and must be reentered if you wish to  
repeat a track on another disc.  
Repeat All Tracks  
Alternating with the track number and program  
step will be a display of the track and the total  
running time of all tracks that have been  
programmed so far. For example, a display of  
0611:25will indicate that track number  
six was the last track programmed, and that the  
total time of all tracks so far is 11 minutes and  
25 seconds. The Total Time Indicators NL  
will flash with this display to remind you of the  
displays contents.  
To repeat all the tracks on a disc in order, press  
the Repeat button r twice while the disc is  
playing and note that the Repeat Indicator  
D and the ALLRepeat-Status Indicator  
E will light. Once the Play button j*˘  
is pressed, the disc will play through from  
beginning to end continuously, until the Stop  
button x&¸ is pressed. The Repeat All  
function may be cancelled at any time by press-  
ing the Repeat button r once until both the  
Repeat Indicator D and ALLRepeat-  
Status Indicators E go out. The Repeat All  
Function is also canceled when the disc drawer  
is opened.  
At any point in the list you may insert a new  
track by simply entering the track number using  
the Numeric Keys p. Simply press the but-  
tons that correspond to the number of the track  
you wish to add. Any tracks that are in the pro-  
gram will remain.  
These displays will alternate three times, and  
then show a steady display of the total time  
and last track programmed.  
To remove a step in the program, first use the  
Program Check button h to locate the  
track you wish to delete. Next, press the Clear  
button 33 . The information in the display will  
blink and the step will be removed from the  
program list. Program steps need not be deleted  
Continue to add tracks in the order you wish to  
have them played until the programming ses-  
18 PROGRAM PLAY  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Program Play  
Repeat A-B  
The CDR 20 may be programmed to repeat any  
section within a track, or a complete passage  
that includes material from a series of consecu-  
tive tracks.  
To program the unit for A-B Repeat play, first  
play the disc and locate the point where you  
wish to begin the repeated section. At the start  
point, press the A-B Repeat button q and  
note that the Repeat Indicator D and the  
Repeat-Status Indicator E will show an A  
and flash. Let the disc play until the point at  
which the section to be repeated will end. At  
that end point, press the A-B Repeat button  
q again and note that the Repeat-Status  
Indicator E will stop flashing and will light  
showing RepeatA-B.  
The unit will immediately begin to play the  
section you have programmed, and continually  
repeat it.  
Note: The program material selected for  
A/B Repeat must be at least 4 seconds long  
for this feature to function.  
To resume normal play, press the A-B Repeat  
button q. The Repeat A-B Indicators  
DE will go out, and the disc will continue  
playing through to the end. Stopping the disc  
or opening the disc drawer will automatically  
cancel the Repeat A-B programming.  
19 PROGRAM PLAY  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CD Recording  
Making recordings on the CDR 20 is simple and  
easy once you become accustomed to the  
basics of CD Recording. Before making your  
first recording, please take a moment to review  
the CDR Basics on page 14. In particular, you  
will need to become familiar with the types of  
discs that may or may not be used in the  
CDR 20. In addition, some terms used in the  
following pages may be new to you. The follow-  
ing definitions and information will help you to  
make CD recordings using the CDR 20s many  
features:  
Next, select a dub speed. The default speed is a  
real-time dub, where the recording takes as  
long as the actual running time of the disc.  
However, with the CDR 20 you may also select  
x2 dubbing or x4 dubbing. Press the Speed  
button s# to select a speed as indicated by  
the x2/x4 Indicators F. When no Speed  
Indicator lights, the unit is set to real-time  
recording. Note that the slower the record-dub  
speed, the more tolerant the unit is of errors on  
the blank disc. However, with most high-quality  
blank discs, the 2x and 4x speeds should not  
present a problem.  
Some commercial CD discs may contain a  
copy protection data bit that will prevent a  
digital copy of the disc to be dubbed. In that  
case, the Copy Prohibit Indicator G will  
light to remind you that the inability to record  
is intentional, and not the result of a problem  
with the CDR 20.  
This product is equipped with the Serial Copy  
Management System (SCMS) to protect the  
rights of copyright owners. Although it is  
possible to make a copy of most CDs for  
your own personal use, it is not possible to  
make a digital copy from another digital copy  
but it is possible to make an analog copy of  
a digital copy.  
The CDR 20 accepts analog inputs and digital  
coax or optical inputs. Before making a  
recording, be certain that you have selected  
the correct input.  
Before beginning a dub, make certain that there  
is sufficient blank space on the record disc. To  
do this, first determine the time available on  
the blank disc by subtracting the time of previ-  
ously recorded material, if any, that is shown in  
the record side Information Display K, from  
the total time available on the disc. That num-  
ber should be greater than the total time of the  
disc to be dubbed, which is shown in the play  
side Information Display K.  
RECORDINGS MAY BE MADE FOR  
PERSONAL USE ONLY, AND ANY  
UNAUTHORIZED COPYING IS SUBJECT  
TO THE APPLICABLE LAW.  
After a disc is recorded, it must be finalized.  
This process adds a table of contents data to  
the disc and makes it playable on other  
machines. Until a disc is properly finalized, it  
may not be played on standard CD players.  
The CDR 20 may record on either CD-R or  
CD-RW discs, but they must be of the type  
specifically designed for use in consumer-  
audio CD recorders. These discs may be rec-  
ognized by looking for the words “Digital  
Audio” in the compact disc logo on the blank  
disc or its packaging. Discs with the logo  
reading only “Compact Disc/Recordable” are  
designed for computer data recording, and  
they will NOT work in the CDR 20.  
The CDR 20 will not copy DVD discs, computer-  
data discs, CD-based computer or video-game  
discs, or digital audio discs with a sample rate  
that is not compatible with the range of the  
CDR 20s sample-rate converter.  
When you are ready to start the dub, press the  
Dubbing Button l). During this process  
the Dubbing Indicator H will light, the  
Record Indicator T will flash and a BUSY  
message will flash in the Record Decks  
Recordings on the CDR 20 may be made in a  
number of ways:  
Discs may be dubbed using the playback  
deck on the CDR 20 as a source. These copies  
may be made in real time, at twice normal  
speed, or at four times normal playback  
speed.  
Recordings may be made from an external  
CD player or other digital source that is  
synchronized with the dub being made in the  
CDR 20.  
Recordings may be made from any compati-  
ble external digital source.  
Recordings may be made from an external  
analog source.  
Information Display K. When both  
Information Display Indicators return to normal,  
with indications of 0100:00, press the  
Play/Select Button j*˘ to start the dub.  
CD-R discs may not be erased or have  
material added to them once they have been  
finalized.  
At least four (4) seconds of blank recording  
time must remain on an unfinalized disc for  
recording to take place.  
While the dub is in progress, you will see the  
track numbers and running time increase as  
the disc is copied. The Level Indicators will also  
flash but this is only for your reference, as  
record levels may not be adjusted during digital  
recordings. It is possible to listen to the source  
disc while it is being dubbed by selecting the  
appropriate input on your receiver, preamp or  
processor.  
The maximum number of tracks that may be  
recorded on a disc is 99.  
Note that some CD-R/CD-RW audio recording  
discs may be used for single-speed recordings  
only. If you use a disc with such a warning,  
make certain not to make a dub at x2 or x4  
speed. However, the CDR 20 has been tested  
for compatibility with a wide range of blank  
discs from manufacturers throughout the  
world. In most cases, blank discs will produce  
high-quality recordings at any dub speed.  
In some rare cases, a CD player may not be  
compatible with CD-R discs. If you find that a  
CD-R disc plays in some players but not in  
others, the fault is most likely with the player,  
not with the recorded disc or the CDR 20.  
Remember that CD-RW discs made in the  
CDR 20 will play only in CD players that are  
specially designed to accommodate CD-RW  
discs. Note that most DVD players are com-  
patible with finalized CD-RW discs.  
CD-RW discs may not be erased and reused  
more than 99 times. This is a limitation of the  
CD-RW format, not a fault of the CDR 20.  
Important Note: When a high-speed (x2 or  
x4) dub is being made, you will hear the play-  
back from the CDP outputs ¡¢• at the  
faster speed. Fast speed playback increases the  
pitch of a sound, and when played back at high  
volume levels this may damage your speakers.  
DO NOT use high volume levels when listening  
to high-speed dubs while they are in progress.  
Disc Dubbing  
The easiest way to make a copy of an entire  
disc is to use the CDR 20s internal dub  
capability.  
First, insert a blank or unformatted disc in the  
Record Drawer %. When the disc is inserted,  
the CDR 20 will examine it to determine if it  
is a CD-R or CD-RW disc, and optimize itself  
for the best possible recording. This is indicated  
by OPCmessage in the Information  
Display K.  
The dub will stop automatically when the  
source disc has played through to the end. After  
the dub is finished, the Information Display will  
show an UPDATEmessage, and then return  
to normal operation. To manually stop a dub-  
bing operation, press the Stop button  
x&¸ for either deck.  
Place the disc to be dubbed in the Play  
Drawer 3 and wait until the Table of  
Contents data is read and the Information  
Display K shows the track and running time  
data for the disc.  
20 CD RECORDING  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CD Recording  
As with all recorded CD-R/CD-RW discs, the  
disc must be finalized before it can be played in  
other machines. See page 22 for instructions on  
disc finalization.  
add track numbers manually by pressing the  
Track Increment button n when you  
wish to increase the track number. This mode  
is recommended for recordings made from  
analog sources.  
The Auto mode will add track numbers auto-  
matically, in one of two ways. When track  
data is present from a digital recording, it will  
be carried over to the new copy disc. Thus,  
when the CD being played moves from one  
track to the next track, the copy disc will also  
increase the track number by one. Activate  
the Auto mode by pressing the Auto/Manual  
button m once and note that the Auto  
Indicator W will light.  
In the Auto mode for recordings from an ana-  
log source or a digital source with no track  
data, the track number will be increased  
when the CDR 20 receives silence for 3 sec-  
onds. After 5 seconds of silence, the recording  
will stop. To activate the Auto mode, press the  
Auto/Manual button m once and note  
that the Auto Indicator W will light.  
To record the entire disc or tape, press the CD  
Sync Button twice so that ALLappears in  
the Record Deck Information Display K.  
When the desired mode has been selected,  
start the playback from the source machine. The  
CDR 20 will automatically recognize the incom-  
ing digital data and begin recording. If the  
source material is a CD, the track numbering  
from the original disc will be carried over to  
the dub. If the playback source is NOT a CD,  
you will have to increment the tracks manually.  
Notes on Dubbing:  
If you wish to make a dub with the tracks in  
a different order from the original disc, omit  
tracks on a disc, or make a dub that mixes  
tracks from different discs, create a Program-  
Playback List before pressing the Play/Select  
button j* to start the dub. Instructions  
for creating a Program List may be found on  
page 18. NOTE: Dubs containing Program  
Lists may be made at either the x1 or x2  
speed. If you attempt to make a Programmed  
Dub at the x4 speed, the unit will automati-  
cally select the x2 speed.  
The recording will continue until the CDR 20  
senses that the playback is finished when there  
in no incoming signal for more than three sec-  
onds. At that point the recording will stop. You  
may also stop the recording at any time by  
pressing the Record Deck Stop button  
x&. When there are only four seconds  
remaining on a blank disc, DISC FULL  
message will appear in the Information  
Display ˚. When you see this message, you  
will need to stop the recording process and,  
when a CD-R is being recorded, insert a new  
blank disc or, when a CD-RW is in use, either  
use a new disc or erase existing tracks follow-  
ing the instructions on page 22.  
The Pause buttons do not operate while a  
dub is in progress.  
Tracks will be added automatically to mirror  
the track structure of the original disc.  
The Total Time indication of the recorded CD  
may vary slightly from the original due to vari-  
ations in the spin speed of each drive, but this  
is normal. No information has been lost in the  
recording process.  
If the original disc being dubbed is a digital  
copy or if it contains copy-prohibit signals, the  
unit will automatically make an analog copy.  
To prepare for a recording, press the Record  
button t8. The Record Indicator T will  
flash, and the word BUSYwill briefly appear  
in the Information Display K. When the  
Display returns to the track and running-time  
information, the unit is ready to record.  
After the recording is complete, an UPDATE  
message will appear briefly, and the unit will  
then return to normal operation. Remember to  
finalize the recorded disc so that it may be used  
in other machines.  
CD Sync Recording  
Once the source material is playing, start the  
actual recording by pressing the Play/Select  
button j*. Note that the Record  
CD Sync recording allows you to make an auto-  
matic digital recording from an external CD  
player or MD. During CD Sync Recording, the  
0record unit starts in sync with the source, and  
tracks are added automatically.  
Recording from an External Source  
To record from an external source, first place a  
CD-R or CD-RW audio disc in the Record  
Deck %. Next, select the input to be used by  
pressing the Input button v. Pressing the  
button will cycle between the input choices,  
which will be shown in the Information  
Display K as COAX, OPTICALor  
ANALOG. In addition, the Digital Indicator  
Y will light when the coax input is selected,  
and the Analog Indicator X will light when  
the analog inputs are selected.  
Indicator T will stop flashing and the  
Information Display K will begin to show  
the running time of the recording and the track  
data. Depending on which mode of track incre-  
ment has been selected as described above,  
track numbers must be increased manually or  
they will be added automatically. Regardless of  
which mode has been selected, a track may be  
added at any time by pressing the Track  
Increment button n.  
To make a CD Sync recording: First, make cer-  
tain your playback source is selected and cued  
to the correct starting point. Next, select the  
appropriate digital input by pressing the Input  
button v until the desired COAXor  
OPTICALindication appears in the Record  
Deck Information Display K. CD Sync  
recordings may not be made from an analog  
input.  
Note: If there is a pause in the playback signal  
for more than 5 seconds for digital recordings  
or 10 seconds for analog recordings, the  
CDR 20 will stop the recording. Also, when the  
Pause button is pressed during a recording, the  
track number will increase by one number and  
the recording will stop and must be restarted  
by pressing the Play/Select button j*.  
When the recording is finished, press the Stop  
button &x.  
Note that when the digital input is selected,  
the connection may be made to either the rear  
panel Coax Input § or the Front-Panel  
Digital Input 6. If a signal is present at both  
coax inputs when a recording is made, the  
front-panel input will be used as the source.  
Next, make certain that there is a fresh disc in  
the Record Drawer for the recording. Press the  
CD Sync button w9 and note that the  
Sync Indicator I will light and the Record  
Indicator T will flash. Select the type of  
recording to be made:  
Press the Auto/Manual button m to select  
how tracks will be numbered on the recorded  
disc.  
To record only the first track from the source  
player, press the CD Sync Button once so that  
1TRKappears in the Record Deck  
Information Display K.  
Unlike conventional analog tape recorders, the  
CDR 20 does not require level setting when  
recordings are made from a digital source.  
The default mode is Manual. In that mode for  
either digital or analog recordings, you must  
21 CD RECORDING  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CD Recording  
may be erased the disc must be unfinalized. If  
the disc is finalized, follow the instructions  
above for unfinalizing before proceeding with  
these steps.  
Although the Level Indicator C will operate,  
this is only informative and the level may not  
be changed or adjusted. However, when you  
are making a recording from an external analog  
source such as a cassette recorder or the ana-  
log output of a receiver or preamp, you should  
adjust the input levels using the Record-Level  
Control ^. Adjust the levels so that the  
blue/white segments of the display are almost  
all lit, and the red segments flash only occa-  
sionally. If the red segments are constantly lit,  
the recording will be distorted and produce  
unacceptable quality.  
other players. The CD Indicator S will  
remain lit.  
Unfinalizing and Erasing CD-RW Discs  
CD-RW discs are unique in that they are both  
recordable and rewritable. This means that you  
may use them over again like a cassette tape.  
However, the process of reusing a CD-RW disc  
is slightly different from that used with tapes.  
To erase only the last track, press the Erase  
button u!. Note that the Information  
Display K will display 01TRKand the  
Erase Indicator V will flash. Press the  
Play/Select button j* within three sec-  
onds and note that the Erase Indicator will stop  
flashing. When the Erase Indicator V goes  
out the Information Display K will show  
the total number of tracks that now remain on  
the disc.  
Unfinalizing a CD-RW Disc  
To keep the material that is already recorded on  
a CD-RW disc but to add an additional track  
and erase single tracks, you must first unfinalize  
the disc. To do that, place the CD-RW disc in  
the Record Deck % and wait until the Table  
of Contents data has been read.  
To stop the recording, press the Stop button  
x&. The recording will automatically stop if  
it takes more space than is available on the  
CD-R/RW disc. A DISC FULLmessage  
will appear to remind you that a new disc is  
needed.  
You may erase more than one track, counting  
backwards from the last track. First, press the  
Erase button u!. Note that the  
Press the Erase button u! twice and  
check to make sure that the Erase Indicator  
V flashes and the word TOCappears in the  
Record Deck Information Display K.  
Within three seconds, press the Play/Select  
button j* to start the process. The Erase  
Indicator V will remain lit and stop flashing,  
and the Information Display K will switch  
to OPCand then back to TOC.  
Information Display will display 01TRKand  
the Erase Indicator V will flash. Press the  
Next button or Previous button  
until the number of tracks to be erased  
appears in the Information Display K. For  
example, when 06TRKappears in the dis-  
play a total of six tracks will be erased, count-  
ing back from the last track on the disc. Next,  
press the Play/Select button j* within  
three seconds of making the track selection and  
note that the Erase Indicator V will stop  
flashing. When the Erase Indicator V goes  
out the Information Display K will show  
the total number of tracks that now remain on  
the disc.  
At the end of a recording, a BUSYmessage  
and an UPDATEmessage will appear briefly,  
and the unit will return to normal operation.  
Remember to finalize the disc after recording so  
that it may be used in other players.  
Finalizing CD-R and CD-RW Discs  
When the process is finished, the Erase  
Indicator V will go out, and the display will  
return to normal. The disc is now ready to have  
single tracks removed or additional tracks  
added.  
Finalizing is a simple process that completes  
the recording of a disc so that it may be used in  
other players. When a recording is finished, a  
disc must be finalized. Once that is done, a  
CD-R disc may not be changed or added to.  
CD-RW discs are “locked” once they are final-  
ized, but they may be unfinalized to permit  
additional recording or erasure.  
Erasing an Entire CD-RW Disc  
Erasing the entire contents of a disc is simple,  
and it does not matter if the disc has been  
finalized or not. To erase the disc, press the  
Erase button u! twice if the disc has  
NOT been finalized and once if it has been  
finalized, so that the word DISCappears in  
the Information Display K and the Erase  
Indicator V flashes. To start the erasure,  
press the Select button j* and note that  
the Erase Indicator V will stop flashing. The  
erasure process takes about a minute, and it is  
complete when the Information Display resets  
to 0000:00 and the Erase Indicator V  
goes out. The disc is now totally erased and  
may be reused.  
Important Note: Tracks at the beginning or in  
the middle of the disc may not be erased until  
all of the tracks after them have been erased.  
To finalize a disc, place it in the Record  
Drawer %. Once the discs Table of Contents  
information has been read and the OPC process  
has been completed, press the Finalize button  
o@ and note that the Finalize Indicator  
U will begin to flash. Within three seconds,  
press the Select button j* and note that  
the Finalize Indicator U will stop flashing.  
Important Note on Erasure and  
Finalization Times: Regardless of the speed  
at which a disc was recorded, the CDR 20 will  
erase and finalize discs at the x4 speed to mini-  
mize the length of the process. However, in  
some cases, it may be necessary for the unit to  
repeat the erasure or finalization due to the  
nature of an individual disc. For that reason, it  
is normal for the time required to complete  
these steps to vary from one disc to another.  
The finalization process will take up to two  
minutes, depending on the length of material  
recorded on the disc. During the finalization  
process the Record Deck will not accept any  
operating commands.  
Erasing a Single Track  
When the finalization process is complete the  
Finalize Indicator U will go out, and the  
R/RW Indicator P will also go out as an  
indication that the disc is now playable on  
The individual tracks on a CD-RW disc may be  
erased one at a time, starting with the last  
track on the disc, or you may erase more than  
one track. Note that before individual tracks  
22 CD RECORDING  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting Guide and Error Messages  
TROUBLESHOOTING GUIDE  
SYMPTOM  
POSSIBLE CAUSE  
No AC power  
SOLUTION  
Unit does not operate when Standby switch  
or remote Power-On is pressed  
Make certain AC power cord is plugged into a live outlet  
Check to see if AC outlet is switch controlled  
Turn on Main Power  
Main Power Switch is off  
Wrong deck selected  
Remote does not function  
Press the CDP button to control the Play Deck;  
press the CDR button to control the Record Deck  
Replace both batteries  
Remove obstructions from front panel or  
connect a remote sensor to the Remote-In Jack  
Dead batteries  
Sensor blocked  
Disc does not erase  
CD-R disc in use  
CD-R discs do not erase, only CD-RW discs may be erased  
Recorded CD-R disc does not play in  
another CD player or DISC ERROR  
message appears in Play Deck  
CD-R disc not finalized  
Finalize the CD-R disc in the CDR 20s Record Deck  
(see page 22)  
Recording suddenly stops  
Input source stopped or paused  
Recordings will stop when the input source is paused  
for more than 3 seconds for digital recordings  
and 10 seconds for analog recordings  
ERROR MESSAGES  
ERROR MESSAGE  
EXPLANATION AND PROBABLE CAUSE  
SOLUTION  
CHECK DISC  
• A record-related button has been pressed when a  
Finalized disc is in the Record Deck %  
• A record-related button has been pressed when a  
standard CD is in the Record Deck %  
Unfinalize the disc to add tracks to a CD-RW disc  
Replace the disc with a blank CD-R or CD-RW disc  
Replace the disc with a blank CD-R or CD-RW disc  
DATA DISC  
DISC ERROR  
DISC FULL  
ERROR  
• A non-audio CD-ROM or a CD-Video disc has been  
placed in the machine  
Only CD Audio and DTS discs will play in the CDR 20;  
replace the disc  
An Unfinalized disc has been placed in the Play Deck 3 Finalize the disc (see page 22)  
• A DVD disc has been placed in the unit  
Replace the disc, the CDR 20 does not play or dub DVD discs  
There are only four seconds of record time remaining  
on the disc being recorded  
Use another blank CD-R or CD-RW disc  
Erase one or more tracks on a CD-RW disc  
The disc is not seated properly  
There is a problem with the disc  
Open the drawer and check to see that the disc is properly seated  
Try another disc  
FAILED  
• A dub has not been completed properly  
More than 99 tracks have been recorded  
Check the play disc  
Repeat the dub process  
FULL  
The CDR 20 does not record more than 99 tracks on a disc  
Replace the disc with a blank CD-R or CD-RW Audio disc  
NO AUDIO  
• A record-related button has been pressed when  
a non-audio disc is in the Record Drawer %  
SVC-1  
There is an internal problem with the CDR 20  
Contact an authorized Harman Kardon service depot  
23 TROUBLESHOOTING GUIDE  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Specifications  
Signal Format  
Playback Sampling Frequency  
D/A Conversion  
Oversampling  
44.1kHz  
96kHz, Multi-Bit Delta-Sigma Conversion  
128 Times  
Playback Specifications  
Frequency Response  
Playback S/N  
2Hz – 20,050Hz  
105dB  
Playback Dynamic Range  
Playback THD  
Analog Audio Output  
Digital-Coaxial Output  
Headphone Output  
105dB  
0.005%/–88dB  
2V RMS, ± 2dB  
0.5Vpp/75  
1V RMS/32Load  
Record Specifications  
Digital Input Sample Rates  
Recording S/N: Analog  
32kHz – 96kHz  
91dB  
Recording S/N: Digital Dub Mode  
Recording S/N: Digital External Source  
Recording Dynamic Range  
Recording THD  
Analog Input Sensitivity  
Digital Inputs (Direct Recording)  
Equal to Source  
Source –10dB  
91dB  
0.005%/–85dB  
330mV RMS 47k= 0dB  
44.1kHz, ±100 ppm/min.  
General  
Power Requirement  
Power Consumption  
Dimensions  
Width  
Height  
Depth  
Weight  
100~240 VAC/50~60Hz  
28 Watts  
17.3"/440mm  
4.4"/112mm  
14.2"/363mm  
10.5 lb/4.7kg  
Depth measurement includes knobs, buttons and connection jacks.  
Height measurement includes feet and chassis.  
All features and specifications are subject to change without notice.  
Harman Kardon is a registered trademark, and  
Power for the digital revolution is a trademark, of Harman Kardon, Inc.  
250 Crossways Park Drive, Woodbury, New York 11797  
© 2000 Harman Kardon, Incorporated  
Part #3828R-D009A  
Download from Www.Somanuals.com. All Manuals Search And Download.  

GSW Water Heater 319594 000 User Manual
Haier Flat Panel Television LED19 User Manual
Haier Refrigerator HUM030PA User Manual
Hamilton Beach Blender 70570C User Manual
Harbor Freight Tools Bicycle Accessories 91212 User Manual
Hayter Mowers Lawn Mower 43F User Manual
Hearth and Home Technologies Indoor Fireplace CF550E User Manual
HP Hewlett Packard Server DL380 G7 User Manual
Icom Two Way Radio IGM1600 User Manual
IKEA Plumbing Product AA 291709 1 User Manual