HITCH COVER WITH BRAKE LIGHT
92043
ASSEMBLY AND OPERATING INSTRUCTIONS
SPECIFICATIONS
Item
Description
Polystyrene, replaceable
Lens
Light Source
Power Requirement
Power Wire
12 bright red LED’s
12 VDC
16 AWG x 2C x 13 (L) inches; Flat four trailer
plug (4-pin slip fit)
Hitch Pin Hole Diameter
Dimensions
Hitch Receiver Depth
Weight
5/8 inch
3-1/4 (square) x 4-3/8 (D) inches
Two inches on square hitch
0.3 lbs.
Receiver Gasket
1/2 inch thick
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright © 2004 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking
When unpacking, check to make sure that all parts are included. Refer to the
Assembly Drawing and Parts List on the next page.
Installation
During installation, refer to the Assembly Drawing.
1. Set the vehicle emergency brake and remove the ignition keys.
2. Plug the vehicle’s trailer brake light connector (Flat 4 trailer plug) into the
Hitch Cover Brake Light Power Wire (A5) plug.
If the vehicle does not have an existing trailer brake light cable installed, have
one installed by a qualified technician. Note that the green wire on the Hitch
Cover Brake Light is connected to the brake light cable of the vehicle. The
other wire is connected to ground, or the chassis.
3. Remove the Cotter Pin (B2) from the Hitch Pin (B1). Slide the Hitch Pin from
the Hitch Cover Brake Light.
4. With the Receiver Gasket in place against the Lens Housing (A4), slide the
Hitch Cover Brake Light into the hitch receiver.
5. Insert the Hitch Pin (B1) through the hole in the Hitch Cover Brake Light and
the hitch.
6. Secure the Hitch Pin (B1) by inserting the Cotter Pin (B2).
7. Test the Hitch Cover Brake Light by pressing down on the vehicle brake
peddle. Have another person view the Hitch Cover Brake Light.
8. Remove and store the Hitch Cover Brake Light before attempting to attach a
trailer to the vehicle hitch.
Maintenance
1. Periodically check that the Lens (A1) is securely seated in the Lens Housing
(A4).
2. Clean the Hitch Cover Brake Light with a cloth dampened with water. Do not
spray the brake light directly with a water hose.
3. When not in use, store the brake light in its original box to keep from
scratching the lens.
SKU 92043
For technical questions, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 3
Parts List
Part No.
A1
Description
Lens
A2
A3
A4
A5
LED Lights (12V-2W)
Power Wire with Plug
Lens Housing
Receiver Gasket
Hitch Pin
B1
B2
Cotter Pin
NOTE: Some parts are listed and shown for illustration purposes only and are not
available individually as replacement parts.
Assembly Drawing
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE
BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR
THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT,
THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THat ALL REPAIRS
AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED
TECHNICIANS AND NOT BY THE BUYER.THE BUYER ASSUMES ALL RISK AND LIABIL-
ITY ARISING OUT OF HIS OR HER REPAIRS TOTHE ORIGINAL PRODUCT OR REPLACE-
MENT PARTSTHERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACE-
MENT PARTS THERETO.
SKU 92043
For technical questions, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 4
|