QUICK ACTION
8-POSITION WORKBENCH
47078
ASSEMBLY & OPERATING INSTRUCTIONS
®
3
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Use eye and ear protection. Always wear ANSI approved impact safety goggles.
9. Do not exceed products maximum load capacity. Make certain that the Workbench can
support all tools and accessories, as well as any workpiece.
10. Avoid Sharp edges when assembling.
11. Always check hardware and assembled parts after assembling. Place in an area that is
flat and level. All connections should be tight and hardware tightened.
12. Do not allow children to play on, stand upon or climb upon the Workbench.
Warning:
The warnings, cautions, and instructions discussed in this instruction manual cannot
cover all possible conditions and situations that may occur. It must be understood by
the operator that common sense and caution are factors which cannot be built into
this product, but must be supplied by the operator.
Assembly
Your Quick Action 8-Position Workbench will require complete assembly prior to use. It is important
that you read the entire manual to become familiar with the product BEFORE use. Before
assembling the Workbench be sure that you have all parts described in the Parts List and Assemby
Diagram located on the last pages of this manual.
Step 1)
Step 2)
Step 3)
Step 4)
Locate the two (2) Left Leg Stand Frames (#26). Attach Tool Holder (front) (#24) to
the Left Leg Stand Frames (#26) by inserting a Hex Bolt (#29) through each corner
of the Tool Holder (front) and through the Left Leg Stand Frame(s). Slide on Flat
Washer (#19) and fasten Hex Nut M6 (#18).
Locate the two (2) Right Leg Stand Frames (#27) and attach Tool Holder (back) (#25)
by inserting a Hex Bolt (#29) through each corner of the Tool Holder (back) (#25) and
through the Right Leg Stand Frame (#27). Slide on Flat Washers (#19) and fasten in
place with Hex Nut M6 (#18).
Attach the Left Leg Stand Frames (#26) to Right Leg Stand Frames (#27). Insert
Hex Bolt (#20) through Right Leg Stand Frames (#27) and slide on Spacer (#17)
then slide on Left Leg Stand Frame and Washer (#19). Secure with Hex Nut (#18).
Repeat for second side of Workbench-see Figure 1.
Attach the Grip (#28) to the lowest hole in the top extension of the Left Leg Stand
Frames (#26) with Hex Bolt (#29) Washer (#19) and Hex Nut (#18)-see Figure 2.
Figure 1
Right Leg Stand Frame (#27)
Spacer (#17)
Hex Nut (#18)
Hex Bolt (#20)
Left Leg Stand Frame
(#26)
Washer (#19)
#47078
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2
Washer (#15) with Hex Nut (#14)
U-Frame Channel (#10)
Cross Head Bolt (#16)
Washer (#19)
Hex Nut (#18)
Grip (#28)
Hex Bolt (#29)
Washer (#19)
Hex Nut (#18)
Step 5)
Step 6)
Through the center hole in the extension, insert Hex Bolt (#29), slide on Washer
(#19) and fasten with Nut (#18)-see Figure 2.
Set the U-Frame Channel (#10) on top of the Right Leg Stand Frame (#27) as shown
in Figure 2. Attach the U-Frame Channel (#10) to the Right Leg Stand Frame (#27)
with Cross Head Bolt (#16); slide on Washer (#15) and tighten on Hex Nut (#14)-see
Figure 2.
Step 7)
Attach the Left Leg Frame Stand (#26) extension to the U-Frame Channel (#10).
First, hold the Spacer 22 mm (#9) between the Left Leg Frame Stand (#26) and the
U-Frame Channel (#10), then insert the Cross Head Bolt (#8) through Left Leg
Frame Stand (#26) through Spacer (#9) and through U-Frame Channel (#10). Slide
on Washer (#15) and Nut (#14)-refer to Figure 3.
Figure 3
Spacer (#9)
U-Frame Channel (#10)
Cross Head Bolt (#8)
Washer (#15) and Nut (#14)
Left Leg Frame Stand (#26)
Step 8)
On the underside of the U-Frame Channel (#10), insert the Sliding Locking
Block (#13) with Spring (#12) (see Figure 4) and Check Pawl (#11). On the top of
the U-Frame Channel, set the Connecting Part (#7).
Figure 4
Spring (#12)
Sliding Locking
Block (#13)
#47078
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 9)
Lay the Table Top Back (#6) on top of the Connecting Parts (#7). Through the inside
hole, insert Cross Head Bolt (#3) with Washer (#4) so that it threads down through
the Connecting Part (#7) and into the Check Pawl (#11) and Sliding Locking
Block (#13).
Step 10)
Step 11)
Step 12)
Through the outside holes in the Table Top Back (#6), thread the Push Button (#2)
into the Connecting Part (#7) and into the Check Pawl (#11) and Sliding Locking
Block (#12).
Lay the TableTop (front) (#23) onto the Threaded Sliding Blocks (#21) which are set
in place on the U-Frame Channel (#10). Screw in Cross Head Bolt (#22) with
Washer (#4) through the Table Top (front) and into the Threaded Sliding Blocks (#21).
As necessary, attach Rubber Feet (#30) to each Leg Stand Frame.
Operation
The Quick Action 8-Position Workbench folds for easy travel and storage.
Step 1)
The Table Top (front) (#23) can be moved by turning the Handles on the U-Frame
Channel (#10). Turning the Handle clockwise will move the Table Top in towards the
other Table Top. Turning the Handle counterclockwise will move the Table
Top (front) (#23) out.
Step 2)
Pressing on the red Push Buttons (#2) with your thumb allows you to grasp the Table
Top (back) (#6) with your hands and fingers and slide it forward or backward while
the Push Buttons (#2) are pressed down. Releasing the Push Buttons (#2) will lock
the Table into place-see Figure 5.
Figure 5
Step 3)
The Swivel Pegs (#1) and Peg Supports (#5) can be placed into any hole in the Work
Table top provide a block to secure and block your workpiece.
PLEASE READTHE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDEDTHE PARTS DIAGRAM INTHIS MANUAL AS A REFERENCE
TOOL ONLY. NEITHERTHE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION ORWARRANTY OF ANY
KINDTOTHE BUYERTHAT HE OR SHE IS QUALIFIEDTO MAKE ANY REPAIRSTOTHE PRODUCT ORTHAT HE OR SHE IS
QUALIFIEDTO REPLACE ANY PARTS OFTHE PRODUCT. IN FACT,THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATESTHAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED
TECHNICIANS AND NOT BYTHE BUYER.THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER
REPAIRSTOTHE ORIGINAL PRODUCT OR REPLACEMENT PARTSTHERETO, OR ARISING OUT OF HIS OR HER
INSTALLATION OF REPLACEMENT PARTSTHERETO.
#47078
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking
When unpacking your Quick Action 8-Position Workbench, check to make sure the following parts
are included. If any parts are missing or broken, please call HARBOR FREIGHT TOOLS at
1-800-444-3353.
Parts List- Quick Action 8-Position W\orbench
Part # Description
Quantity Part # Description
Quantity
1
2
3
4
5
6
7
7A
8
Swivel Peg
Push Button
4
2
2
4
2
1
2
2
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Cross Head Bolt m 8 x 45
Spacer 9.5 mm
Hex Nut
2
2
10
10
2
2
2
1
1
1
1
1
1
8
4
Cross head Bolt M8 x 65
Washer 8 x 21 mm
Peg Support
Table Top (back)
Connecting Part
Connecting Part
Flat Washer 6 x 12 mm
Hex Bolt M6 x 58
Threaded Sliding Block
Cross Head Bolt M8 x 50
Table Top (front)
Tool Holder (front)
Tool Holder (back)
Left Leg Stand Frame
Right Leg Stand Frame
Grip
Cross Head Bolt M8 x 55 2
9
Spacer 22 mm
U-Frame Channel
Check Pawl
Spring
Sliding Locking Block
Hex Nut M 8
2
2
2
2
2
4
4
10
11
12
13
14
15
Hex Bolt M 6 x 35
Rubber Feet
Flat Washer 8 x 16 mm
Note: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
#47078
Page 6
REV 01/05
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts/Assembly Diagram
21
7A
21
7A
#47078
Page 7
REV 01/05
Download from Www.Somanuals.com. All Manuals Search And Download.
|