MODEL T10042
26" LAWN SWEEPER
INSTRUCTION SHEET
D
C
To reduce the risk of injury from using this
product:
E
F
•
Do not allow anyone to operate the
sweeper without proper training.
•
•
Do not allow children to use the sweeper.
Always wear proper eye protection
when using the sweeper.
•
If an object becomes lodged in the
sweeper, do not attempt to remove it
while the sweeper brush is moving.
Figure 1. Inventory 1.
•
•
Keep all hardware tightened to be sure
the sweeper is in safe working order.
G
Thoroughly inspect the sweeper for
damage after striking any foreign
objects.
M
H
I
Inventory (Figures 1 and 2)
N
A. Sweeper Assembly (not shown)................. 1
B. Leaf Bag (not shown)................................. 1
C. Long Bag Rod (27¼") ................................ 1
D. Short Bag Rod (25½")................................ 1
E. Frame Handle............................................. 1
F. Frame Legs ................................................ 2
G. Hex Bolts M6-1 x 30................................... 4
H. Lock Washers 6mm ................................... 4
I. Hex Nuts M6-1 ........................................... 4
J. Carriage Bolts M6-1 x 30 ........................... 4
K. Lock Nuts M6-1.......................................... 4
L. Bag Clips.................................................... 4
M. Hairpin Cotter Pins..................................... 2
N. Rubber Caps .............................................. 2
L
J
K
Figure 2. Inventory 2.
COPYRIGHT © NOVEMBER, 2007 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#JB10062 PRINTED IN CHINA
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations
The Model T10042 can be raised or lowered to
achieve the optimal sweeping height for different
surfaces and for different operators.
Maintenance
To prevent unnecessary wear, periodically lubri-
cate the brush shaft bushings, the wheel bush-
ings, and grease the ratchet gears in each wheel
assembly.
The optimal height adjustment allows the operator
to handle the sweeper comfortably and positions
the brushes so that they extend approximately ½"
into the grass.
To lubricate the bushings (twice annually):
1. Tilt the sweeper onto its side and apply a few
drops of light oil to the brush shaft, as shown
in Figure 9.
To adjust the brush height:
1. Loosen the height adjustment knob, then
slide the adjustment bar downward to raise
the brushes or upward to lower the brushes.
When the desired height is reached, tighten
the height adjustment knob (Figure 8).
Brush Shaft
Height
Adjustment Knob
Brush Shaft
Bushing
Adjustment Bar
Apply Oil Here
Figure 9. Brush shaft bushing lubrication.
2. With the sweeper still on its side, remove the
dust cap on the exposed wheel, then apply
a few drops of light oil to the wheel axle, as
shown in Figure 10, and spin the wheel to
distribute the oil.
Figure 8. Height adjustment.
Tips for using the Model T10042 Lawn
Sweeper:
•
•
Empty the leaf bag after every use.
Wheel Axle
Wheel Axle
To dump the leaf bag, tilt the sweeper all the
way forward.
•
•
For best results and ease of use, be sure the
height is properly adjusted for both the sur-
face being swept and the user's height.
Apply Oil Here
Bushing
Follow the maintenance schedule outlined
in these instructions to prevent unnecessary
wear on your sweeper.
Figure 10. Wheel axle lubrication.
-3-
T10042 26" Lawn Sweeper
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Replace the dust cap and allow the oil to pen-
etrate for a few minutes. Flip the sweeper on
to the other side and repeat Steps 1-3 for the
other bushings.
2. Remove the retaining clip from the brush
shaft, then remove the spacers (Figure 13).
Every two years, the ratchet assemblies in each
wheel should be cleaned and greased.
Note: When performing this procedure, take
notes on the position of all washers, spacers,
and retaining rings. Work on one side at a time to
avoid mixing directional components.
Brush Shaft
Ratchet Gear
Retaining Clip
To grease the ratchet assemblies:
Ratchet Gear
Spacers
1. Remove the dust cover and the retaining clip
holding the wheel, then remove the wheel
(Figures 11 and 12).
Figure 13. Ratchet gear assembly.
3. Remove the ratchet gear and the ratchet pin
(Figure 14).
Brush Shaft
Ratchet Gear
Wheel
Figure 11. Retaining clip removal.
Ratchet Pin
Figure 14. Ratchet gear assembly.
Ratchet Gear
4. Thoroughly clean, then grease the parts
using multipurpose grease. Re-assemble in
the reverse order from disassembly.
5. Repeat for the other wheel.
Wheel
Figure 12. Wheel removed.
-4-
T10042 26" Lawn Sweeper
Download from Www.Somanuals.com. All Manuals Search And Download.
With extensive use, the brushes on the Model
T10042 may become worn and require replace-
ment.
Brush
Rotation
Overlap Bristles
To replace the brushes:
1. Tilt the sweeper all the way forward to allow
easy access to the brushes. For the sake of
simplicity, only replace one brush at a time.
Remove
2. Remove the lock nuts and hex bolts indicated
in Figure 15, and remove the old brushes.
It is not necessary to remove the bolts and
nuts connecting the brush holder to the brush
shaft.
Brush
Rotation
Figure 15. Brush assembly (end view).
3. Install the new brush, making sure the over-
lap bristles are properly oriented in relation-
ship to the direction of brush rotation, as
shown in Figure 15. Tighten the hex nuts.
-5-
T10042 26" Lawn Sweeper
Download from Www.Somanuals.com. All Manuals Search And Download.
T10042 Parts & Labels Breakdown and List
��
��
��
��
��
��
��
��
��
��
��
��
��
48
��
��
��
�
��
��
��
��
��
��
��
��
��
��
��
��
��
��
�
�
�
��
��
��
�
��
��
�
��
�
�
�
��
��
��
�
��
�
REF PART #
DESCRIPTION
WHEEL DUST COVER
REF PART #
PT10042025
DESCRIPTION
1
PT10042001
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
FRICTION WASHER
PINION GEAR RIGHT
SWEEPER BODY
CARRIAGE BOLT M8-1.25 X 55
HEX BOLT M6-1 X 30
BRUSH CLAMP
2
PR06M
EXT RETAINING RING 16MM
FLAT WASHER 16MM
WHEEL BUSHING
WHEEL
PT10042026
PT10042027
PCB28M
3
PW08M
4
PT10042004
PT10042005
PR05M
5
PB29M
6
EXT RETAINING RING 15MM
OUTER SHIM
PT10042030
PT10042031
PLN03M
7
PT10042007
PT10042008
PT10042009
PT10042010
PT10042011
PT10042012
PW04M
BRUSH RETAINER
LOCK NUT M6-1
8
PINION GEAR LEFT
PIN
9
PLN02M
LOCK NUT M5-.8
HEX BOLT M6-1 X 20
HEX BOLT M5-.8 X 25
BRUSH ASSEMBLY
BRUSH SHAFT
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
INNER SHIM
PB08M
BRUSH AXLE BUSHING
WHEEL AXLE
PB94M
PT10042036
PT10042037
PT10042038
PCB29M
FLAT WASHER 10MM
LOCK NUT M8-1.25
DUST COVER ASSEMBLY
HEX NUT M10-1.5
ENDPLATE BUSHING
LOCK NUT M10-1.5
HEX BOLT M8-1.25 X 12
CONNECTOR TUBE
FEMALE KNOB M8-1.25
FLAT WASHER 8MM
LOCK WASHER 8MM
LOCK NUT M6-1
PT10042014
PT10042015
PN02M
BAG CLIP
CARRIAGE BOLT M6-1 X 30
HOPPER BAG
PT10042040
PT10042041
PT10042042
PT10042043
PT10042044
PT10042045
PT10042046
PLW04M
PT10042017
PLN05M
FRAME LEG
RUBBER CAP
PB06M
SHORT BAG ROD
LONG BAG ROD
HAIRPIN COTTER PIN
FRAME HANDLE
PT10042020
PT10042021
PW01M
PLW04M
LOCK WASHER 8MM
GRIZZLY.COM LABEL
PLN03M
PT10042048
Download from Www.Somanuals.com. All Manuals Search And Download.
|