150 WATT PORTABLE
CLAMP LIGHT
35149
ASSEMBLY & OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright© 2006 by Harbor Freight Tools®. All rights reserved. No portion of this manual or
any artwork contained herein may be reproduced in any shape or form without the express
written consent of Harbor Freight Tools.
For technical questions and replacement parts please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL SAFETY
4.
5.
Grounded lights must be plugged into an outlet properly installed and grounded in ac-
cordance with all codes and ordinances. Never remove the grounding prong or mod-
ify the plug in any way. Do not use any adapter plugs. Check with a qualified elec-
trician if you are in doubt as to whether the outlet is properly grounded. If the tools
should electrically malfunction or break down, grounding provides a low resistance path to
carry electricity away from the user.
Double insulated lights are equipped with a polarized plug (one blade is wider than
the other). This plug will fit in a polarized outlet only one way. If the plug does not fit
fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electri-
cian to install a polarized outlet. Do not change the plug in any way. Double insulation
eliminates the need for the three wire grounded power cord and grounded power supply
system.
6.
7.
8.
Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and
refrigerators. There is an increased risk of electric shock if your body is grounded.
Do not expose the Clamp Light to rain or wet conditions. Water entering a power tool
will increase the risk of electric shock.
Do not abuse the Power Cord. Never use the Power Cord to carry the light or pull the
Plug from an outlet. Keep the Power Cord away from heat, oil, sharp edges, or moving
parts. Replace damaged Power Cords immediately. Damaged Power Cords increase
the risk of electric shock.
9.
When operating a light outside, use an outdoor extension cord marked “W-A” or “W”.
These extension cords are rated for outdoor use, and reduce the risk of electric shock.
PERSONAL SAFETY
10.
Stay alert. Watch what you are doing, and use common sense when operating the
Clamp Light. Do not use the Clamp Light while tired or under the influence of drugs,
alcohol, or medication. A moment of inattention while operating the light may result in
serious personal injury.
11.
12.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your
hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair
can be caught in moving parts.
Avoid accidental starting. Be sure the Power Switch is off before plugging in.
Carrying the Clamp Light with your finger on the Power Switch, or plugging in the light with
the Power Switch on, invites accidents.
13.
14.
Remove adjusting keys or wrenches before turning the Clamp Light on. A wrench or a
key that is left attached to a rotating part of the light may result in personal injury.
Do not overreach. Keep proper footing and balance at all times. Proper footing and
balance enables better control of the Clamp Light in unexpected situations.
SKU 35149
For technical questions please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
15.
16.
Use safety equipment. Always wear eye protection.
TOOL USE AND CARE
Do not force the Clamp Light. Use the correct tool for your application. The correct
tool will do the job better and safer at the rate for which it is designed.
17.
18.
Do not use the light if the On/Off Switch does not turn it on or off.
Disconnect the Power Cord Plug from the power source before making any
adjustments, changing accessories, or storing the tool. Such preventive safety
measures reduce the risk of starting the tool accidentally.
19.
20.
21.
Store the Clamp Light out of reach of children and other untrained persons. The
Clamp Light is dangerous in the hands of untrained users.
Maintain the Light with care. Do not use a damaged light. Tag damaged light “Do not
use” until repaired.
Check for misalignment or binding of moving parts, breakage of parts, and any other
condition that may affect the light’s operation. If damaged, have the light serviced
before using. Many accidents are caused by poorly maintained lights.
22.
Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may become hazardous when used on
another light.
SERVICE
23.
24.
Light service must be performed only by qualified repair personnel. Service or
maintenance performed by unqualified personnel could result in a risk of injury.
When servicing a light, use only identical replacement parts. Follow instructions
in the “Inspection, Maintenance, And Cleaning” section of this manual. Use of
unauthorized parts or failure to follow maintenance instructions may create a risk of electric
shock or injury.
GROUNDING
WARNING!
Improperly connecting the grounding wire can result in the risk of electric shock. Check
with a qualified electrician if you are in doubt as to whether the outlet is properly grounded.
Do not modify the power cord plug provided with the Stapler. Never remove the grounding
prong from the plug. Do not use the Stapler if the power cord or plug is damaged. If
damaged, have it repaired by a service facility before use. If the plug will not fit the outlet,
have a proper outlet installed by a qualified electrician.
SKU 35149
For technical questions please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
GROUNDED TOOLS:TOOLS WITH THREE PRONG PLUGS
Note: The Clamp Light has a Three Prong Plug.
1.
2.
3.
Tools marked with “Grounding Required” have a three wire cord and three prong grounding
plug. The plug must be connected to a properly grounded outlet. If the Stapler
should electrically malfunction or break down, grounding provides a low resistance path to
carry electricity away from the user, reducing the risk of electric shock. (See Figure A.)
The grounding prong in the plug is connected through the green wire inside the cord to the
grounding system in the tool. The green wire in the cord must be the only wire connected to
the Stapler’s grounding system and must never be attached to an electrically “live” terminal.
(See Figure A.)
A grounded appliance must be plugged into an appropriate outlet, properly installed and
grounded in accordance with all codes and ordinances. The plug and outlet should look like
those in the following illustration. (See Figure A.)
Figure A
DOUBLE INSULATED APPLIANCES: APPLIANCES WITH TWO PRONG PLUGS
1.
2.
Appliances marked “Double Insulated” do not require grounding. They have a special double
insulation system which satisfies OSHA requirements and complies with the applicable
standards of Underwriters Laboratories, Inc., the Canadian Standard Association, and the
National Electrical Code. (See Figure B.)
Double insulated tools may be used in either of the 120 volt outlets shown in the following
illustration. (See Figure B.)
Figure B
SKU 35149
For technical questions please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
EXTENSION CORDS
1.
2.
Grounded appliances require a three wire extension cord. Double Insulated products can
use either a two or three wire extension cord.
As the distance from the supply outlet increases, you must use a heavier gauge extension
cord. Using extension cords with inadequately sized wire causes a serious drop in voltage,
resulting in loss of power and possible tool damage. (See Figure C, next page.)
3.
4.
5.
6.
7.
The smaller the gauge number of the wire, the greater the capacity of the cord. For
example, a 14 gauge cord can carry a higher current than a 16 gauge cord. (See Figure C.)
When using more than one extension cord to make up the total length, make sure each cord
contains at least the minimum wire size required. (See Figure C.)
If you are using one extension cord for more than one tool, add the nameplate amperes and
use the sum to determine the required minimum cord size. (See Figure C.)
If you are using an extension cord outdoors, make sure it is marked with the suffix “W-A”
(“W” in Canada) to indicate it is acceptable for outdoor use.
Make sure your extension cord is properly wired and in good electrical condition. Always
replace a damaged extension cord or have it repaired by a qualified electrician before using
it.
8.
Protect your extension cords from sharp objects, excessive heat, and damp or wet areas.
Figure C
SKU 35149
For technical questions please call 1-800-444-3353.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFIC SAFETY RULES
1.
2.
WARNING! Do not mount the Clamp Light on or in any residential structure. Mounting
in such a location creates a fire hazard that can result in property damage, severe
personal injury, and/or death.
ALWAYS point the Light away from the wall, whether the unit is in use or not. If the
light is accidentally pointed at the wall while it is on or while it is still hot when turned off, a
fire may result.
3.
4.
5.
6.
7.
Keep all flammable materials and wall hangings at least 10 feet from the mounting
location.
Make sure to turn off the Clamp Light and unplug the unit from its electrical outlet
when unattended.
Immediately upon turning on the Clamp Light, the Halogen Bulbs become VERY
hot. While operating the unit, do not touch the Halogen Bulbs, or grid.
Avoid excessive UV radiation. Should your skin begin to feel hot while operating the
Halogen Lamps, immediately remove yourself from the unit’s light rays.
Avoid serious eye injury. Do not look directly into the Halogen Bulbs when operating this
product. Always wear ANSI approved safety goggles when working with tools and
equipment.
8.
Do not touch the Halogen Bulb at any time. Oil from skin will drastically shorten the
bulb’s life-span if not cleaned (with rubbing alcohol) before use. Handle with a soft, clean
cloth instead.
9.
Do not operate the Clamp Light with a missing or damaged Lens or Grid.
Do not operate the Clamp Light with the Grid open.
10.
11.
Turn off the Clamp Light, unplug its Power Cord from its 120 volt, grounded, electrical
outlet, and allow it to completely cool down prior to performing any inspection, main-
tenance, or cleaning on the unit.
12.
13.
After its use, make sure to allow the Light to completely cool down before storing the
unit.
Be careful when hanging or clamping the Light in place. Make certain that the area
used to hang the Light is clear of debris and obstructions which may bump the Light.
14.
15.
Do not obstruct walkways or common areas with the cord.
The Clamp Light is weatherproof but not waterproof. Do not submerge the Light in
water.
SKU 35149
For technical questions please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLOGY
Double Insulated
Canadian Standards
Association
Underwriters
Laboratories, Inc.
Volts Alternating Current
V ~
Amperes
A
n
No Load Revolutions
Per Minute (RPM)
o
xxxx/min.
WARNING! The warnings, precautions, and instructions discussed in this manual cannot
cover all possible conditions and situations that may occur. The operator must understand
that common sense and caution are factors which cannot be built into this product, but
must be supplied by the operator.
Unpacking
When unpacking the 150 Watt Portable Clamp Light, check to make sure parts on page are
included. If any parts are missing or broken, please call HARBOR FREIGHT TOOLS at
1-800-444-3353.
Assembly
Your Portable Clamp Light will require some minor assembly. The Light requires special conditions
for set up and operation. It is important that you read the entire manual to become familiar with the
product BEFORE you use the Portable Clamp Light. Before operating the Portable Clamp Light be
sure that you have all parts described in the Parts List and Assembly Diagram located on page 10
of this manual.
1.
The Light comes with a Spring Clamp (1) and a hook, either of which can be used to hang
the Clamp Light. The hook can be turned to face up or down on the Spring Clamp as shown
in Figure 1.
Figure 1
Press here
to separate
Clamp (1)
clamp
Spring
Hook
SKU 35149
For technical questions please call 1-800-444-3353.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
2.
3.
The Spring Clamp (1) can be mounted to the Bracket (7) at any of the three holes
located at the end of the Spring Clamp (1). Decide on the angle to attach the Spring
Clamp (1) to the Bracket (7) - see Figure 2. Thread in Phillips Head Bolt (5) through the
Bracket (7) and into the Spring Clamp (1). If the Phillips Head Bolt (5) does not thread in
tightly, you may have to add several washers (not included) to obtain a tight fit.
The Clamp Light has a Handle (2), which should be mounted to the grommet in the top
of the Clamp Light by using a Knob (3) - see Figure 3.
Figure 3
Figure 2
Knob (3)
Knob (3)
Handle (2)
Wing Knob (8)
Bracket (7)
Spring Clamp (1)
4.
1.
The Bracket (7) is held in place by two Knobs (3). To rotate the Clamp Light in place,
loosen the Knobs (3) and move the Clamp Light to the desired position. Tighten Knobs (3).
Bulb Replacement
Make certain that the product is OFF and unplugged. With leather gloves on, squeeze and
remove the Grid from the front of the Clamp Light.
2.
3.
4.
Remove the Bolt from the top of the Clamp Light-see Figure 3.
Pull out the Lens from the front of the Clamp Light.
Make certain that the Halogen Bulb has had sufficient time to cool. Gently pull out the
Halogen Bulb.
5.
6.
Making certain NOT TO TOUCH the new Halogen Bulb, insert it into the Clamp Light
left side first. Oil from your skin will drastically shorten the bulb’s life-span if not cleaned
(with rubbing alcohol) before use. Handle with a soft, clean cloth instead.
Insert the Phillips Head Bolt (3) and replace the Grid.
SKU 35149
For technical questions please call 1-800-444-3353.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
1.
2.
To turn on the Clamp Light, plug the Power Cord into the nearest 120 volt, grounded,
electrical outlet. Then, press the On/Off Switch located on the back of the Clamp Light.
WARNING! Always point the light away from the wall, whether the unit is in use or
not. If the unit is accidentally pointed at the wall while turned on or still hot after turned off, a
fire may result.
To turn off the Halogen Light, press the On/Off Switch located on the back of the Light.
Then, unplug the Power Cord/Plug from its electrical outlet.
Inspection, Maintenance and Cleaning
1.
2.
Always unplug the Halogen Lamp from its electrical outlet and allow the unit to completely
cool down before performing any inspection, maintenance, or cleaning.
Before each use: Inspect the general condition of the Halogen Lamp. Check for
misalignment or binding of moving parts, cracked or broken parts, damaged Power Cord,
damaged Grid, Lens and any other condition that may affect its safe operation. If a problem
occurs with the Clamp Light, have the problem corrected before further use. Do not use
damaged equipment.
Parts List
Parts Diagram
Part
Description
Q’ty
2
1
2
3
4
5
6
7
8
9
6” Spring Clamp
1
1
2
2
3
1
1
1
1
1
Handle
Knob
9
5
Note:
#8
hidden
from view.
10
Flat Washer
Phillips Head Bolt
Halogen Bulb
Bracket
Wing Knob
Light Housing w/Cord
6
3
4
7
10 Grid
1
Note: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDEDTHE PARTS DIAGRAM INTHIS MANUAL AS A REFERENCETOOL
ONLY. NEITHERTHE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KINDTO
THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED
TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES
THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS
AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTSTHERETO,OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT
PARTS THERETO.
SKU 35149
For technical questions please call 1-800-444-3353.
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED 90 DAY WARRANTY
Harbor FreightTools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for
the period of ninety days from the date of purchase. This warranty does not apply to damage due directly or
indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, or to lack of
maintenance.We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent,
special or consequential damages arising from the use of our product. Some states do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our
inspection verifies the defect, we will either repair or replace the product at our election or we may elect to
refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return
repaired products at our expense, but if we determine there is no defect, or that the defect resulted from
causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
SKU 35149
For technical questions please call 1-800-444-3353.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
|