7” 1.5 HP TILE SAW
WITH STAND
92386
ASSembly AND OperATION INSTrucTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
TO preVeNT SerIOuS INjury, reAD AND uNDerSTAND
All WArNINgS AND INSTrucTIONS befOre uSe.
Copyright© 2005 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
for technical questions or replacement parts, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
WOrK AreA
1.
2.
Keep your work area clean and well lit. Cluttered and dark work areas invite
accidents.
Do not operate power tools in explosive atmospheres, such as in the pres-
ence of flammable liquids, gases, or dust. Power tools create sparks which may
ignite the dust or fumes.
3.
1.
Keep bystanders, children, and visitors away while operating a power tool.
Distractions can cause you to lose control.
elecTrIcAl SAfeTy
grounded tools must be plugged into an outlet properly installed and grounded
in accordance with all codes and ordinances. Never remove the grounding
prong or modify the plug in any way. Do not use any adapter plugs. check
with a qualified electrician if you are in doubt as to whether the outlet is prop-
erly grounded. If the tool should electrically malfunction or break down, grounding
provides a low resistance path to carry electricity away from the user.
2.
Avoid body contact with grounded surfaces such as pipes, radiators, ranges,
and refrigerators. There is an increased risk of electric shock if your body is
grounded.
3.
4.
Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
Do not abuse the power cord. Never use the power cord to pull the plug from
an outlet. Keep the power cord away from heat, oil, sharp edges, or moving
parts. replace damaged power cords immediately. Damaged Power Cords
increase the risk of electric shock.
5.
When operating a power tool outside, use an outdoor extension cord marked
“W-A” or “W”. These extension cords are rated for outdoor use, and reduce the
risk of electric shock.
perSONAl SAfeTy
1.
2.
Stay alert. Watch what you are doing, and use common sense when oper-
ating a power tool. Do not use a power tool while tired or under the influence
of drugs, alcohol, or medication. A moment of inattention while operating power
tools may result in serious personal injury.
Dress properly. Do not wear loose clothing or jewelry. contain long hair.
Keep your hair, clothing, and gloves away from moving parts. Loose clothes,
jewelry, or long hair can be caught in moving parts.
SKU 92386
for technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
4.
Avoid accidental starting. be sure the power Switch is off before plugging in.
Plugging in power tools with the Power Switch on invites accidents.
remove adjusting keys or wrenches before turning the power tool on. A
wrench or a key that is left attached to a rotating part of the power tool may result
in personal injury.
5.
6.
Do not overreach. Keep proper footing and balance at all times. Proper footing
and balance enables better control of the power tool in unexpected situations.
use safety equipment. Always wear eye protection. Wear an ANSI approved
full face shield and non-skid safety shoes. ANSI approved hearing and breathing
protection must be used for appropriate conditions.
TOOl uSe AND cAre
1.
use clamps (not included) or other practical ways to secure and support a
smaller workpiece to a stable platform. Holding the work by hand or against your
body is unstable and may lead to loss of control.
2.
3.
Do not force the tool. use the correct tool for your application. The correct
tool will do the job better and safer at the rate for which it is designed.
Do not use the power tool if the power Switch does not turn it on or off. Any
tool that cannot be controlled with the Power Switch is dangerous and must be
replaced.
4.
Disconnect the power cord plug from the power source before making any
adjustments, changing accessories, or storing the tool. Such preventive safety
measures reduce the risk of starting the tool accidentally.
5.
6.
Store idle tools out of reach of children and other untrained persons. Tools
are dangerous in the hands of untrained users.
maintain tools with care. Keep tools clean. Properly maintained tools are easier
to control. Do not use a damaged tool. Tag damaged tools “Do not use” until re-
paired.
7.
8.
check for misalignment or binding of moving parts, breakage of parts, and any
other condition that may affect the tool’s operation. If damaged, have the tool
serviced before using. Many accidents are caused by poorly maintained tools.
use only accessories that are recommended by the manufacturer for your
model. Accessories that may be suitable for one tool may become hazardous
when used on another tool.
SKU 92386
for technical questions, please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
SerVIce
1.
2.
Tool service must be performed only by qualified repair personnel. Service or
maintenance performed by unqualified personnel could result in a risk of injury.
When servicing a tool, use only identical replacement parts. follow instruc-
tions in the “Inspection, Maintenance, And Cleaning” section of this manual.
Use of unauthorized parts or failure to follow maintenance instructions may create
a risk of electric shock or injury.
grOuNDINg
WArNINg!
Improperly connecting the grounding wire can result in the risk of electric shock.
check with a qualified electrician if you are in doubt as to whether the outlet is
properly grounded. Do not modify the power cord plug provided with the tool.
Never remove the grounding prong from the plug. Do not use the tool if the
power cord or plug is damaged. If damaged, have it repaired by a service facil-
ity before use. If the plug will not fit the outlet, have a proper outlet installed by
a qualified electrician.
grOuNDeD TOOlS:TOOlS WITH THree prONg plugS
1.
2.
3.
Tools marked with “Grounding Required” have a three wire cord and three prong
grounding plug. The plug must be connected to a properly grounded outlet. If
the tool should electrically malfunction or break down, grounding provides a low
resistance path to carry electricity away from the user, reducing the risk of electric
shock. (See figure A.)
WArNINg: To reduce the risk of electroncution, keep all connections dry and off
the ground. Do not touch plug with wet hands. Ground Fault Circuit Interrupter
(GFCI) protection should be provided on the circuit(s) or outlet)s) to be used for the
tile saw (GFCI is not included in this machinery). Receptacles are available having
built-in GFCI protection and may be used for this measure of safety.
The grounding prong in the plug is connected through the green wire inside the
cord to the grounding system in the tool. The green wire in the cord must be the
only wire connected to the tool’s grounding system and must never be attached to
an electrically “live” terminal. (See figure A.)
REV 12/06
SKU 92386
for technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
4.
Your tool must be plugged into an appropriate outlet, properly installed and grounded
in accordance with all codes and ordinances. The plug and outlet should look like
those in the following illustration. (See figure A.)
fIgure A
exTeNSION cOrDS
1.
2.
Grounded tools require a three wire extension cord. Double Insulated tools can
use either a two or three wire extension cord.
As the distance from the supply outlet increases, you must use a heavier gauge
extension cord. Using extension cords with inadequately sized wire causes a seri-
ous drop in voltage, resulting in loss of power and possible tool damage.
(See figure b, next page.)
3.
The smaller the gauge number of the wire, the greater the capacity of the cord. For
example, a 14 gauge cord can carry a higher current than a 16 gauge cord.
(See figure b.)
4.
5.
When using more than one extension cord to make up the total length, make sure
each cord contains at least the minimum wire size required. (See figure b.)
If you are using one extension cord for more than one tool, add the nameplate am-
peres and use the sum to determine the required minimum cord size.
(See figure b.)
6.
7.
If you are using an extension cord outdoors, make sure it is marked with the suffix
“W-A” (“W” in Canada) to indicate it is acceptable for outdoor use.
Make sure your extension cord is properly wired and in good electrical condition.
Always replace a damaged extension cord or have it repaired by a qualified electri-
cian before using it.
8.
Protect your extension cords from sharp objects, excessive heat, and damp or wet
areas.
reV 03/05
SKU 92386
for technical questions, please call 1-800-444-3353.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
recOmmeNDeD mINImum WIre gAuge fOr exTeNSION cOrDS*
(120 Or 240 VOlT)
NAmeplATe
AmpereS
(at full load)
exTeNSION cOrD leNgTH
25 feet
50 feet
75 feet 100 feet 150 feet
0 – 2.0
2.1 – 3.4
18
18
18
18
18
14
12
18
18
18
16
14
12
10
18
18
16
14
12
10
-
18
16
14
12
10
-
16
14
12
12
-
3.5 – 5.0
5.1 – 7.0
7.1 – 12.0
12.1 – 16.0
16.1 – 20.0
-
-
-
* based on limiting the line voltage drop to five volts at 150% of the rated amperes.
fIgure b
SymbOlOgy
Double Insulated
Canadian Standards Association
Underwriters Laboratories, Inc.
Volts Alternating Current
V~
A
Amperes
No Load Revolutions per Minute (RPM)
n xxxx/min.
0
SKU 92386
for technical questions, please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
SpecIfIc SAfeTy ruleS
1.
2.
maintain labels and nameplates on theTile Saw. These carry important informa-
tion. If unreadable or missing, contact Harbor Freight Tools for a replacement.
use the right product for the right job. There are certain applications for which
this product was designed. Do not use small equipment, tools, or attach-ments to
do the work of larger industrial equipment, tools, or attachments. Do not use this
product for a purpose for which it was not intended.
3.
4.
5.
This product must continuously run with cold water. Dry running will cause
serious damage to the pump seals.
WArNINg! Keeps hands and fingers away from cutting area and Saw blade.
Use a “push stick” (not included) when necessary.
check blade guard for proper forward/backward movement before each use.
Do not operate the Tile Saw if the Blade Guard does not move freely. Make sure
the Blade Guard moves freely and does not touch the Saw Blade or any other part
of the Saw, in all angles and depths of cut.
6.
7.
Do not handle the power Switch with wet hands.
make sure the Tile Saw is located on a flat, level, sturdy surface capable of
supporting the weight of the Saw and work pieces.
8.
9.
Always use Diamond Saw blades with a 7” diameter, 5/8” round arbor hole,
and rated at 3550 rpm or greater.
use the Tile Saw only for cutting ceramic tile, quarry tile, marble, terra-cotta,
and slate with a maximum thickness of 1”if cutting at a 90 degree angle or 1”
if cutting at a 45 degree angle.
10.
Do not use the Tile Saw for cutting metals or for cutting curves. This may
cause the Saw Blade to break and/or reduce it s service life.
11.
12.
make sure the Saw blade is wet at all times when cutting.
Keep all electrical connections dry and off the ground.
REV 12/06
SKU 92386
for technical questions, please call 1-800-444-3353.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
pOWer cOrD
TIle SAW
120 VOlT,
grOuNDeD
elecTrIcAl
OuTleT
fIgure c
DrIp lOOp
13.
Always arrange a “drip loop” in the power cord connecting the Tile Saw to a
120 volt, grounded, electrical outlet. A drip loop is that part of the Power Cord
below the level of the outlet, or the connector if an extension cord is used, to pre-
vent water traveling along the Power Cord and coming in contact with the outlet.
If the Power Plug or electrical outlet does get wet, do not unplug the Power Cord.
Disconnect the fuse or circuit breaker that supplies power to the tool. Then, unplug
and examine for presence of water in the outlet. (See figure c.)
14.
15.
16.
17.
18.
19.
use cold water only. Never use hot water. Using hot water can damage the
Pump seals.
Never run theTile Saw without a water supply. Running the unit without a water
supply will cause irreparable damage to the Pump.
make sure the water supply used for theTile Saw is not dirty, sandy, and does
not contain any corrosive chemical products.
make sure to change the water when necessary while in use and rinse out
the Tub after every use.
Never leave theTile Saw unattended when it is plugged into an electrical outlet.
Turn off the Tile Saw, and unplug it from its electrical outlet.
Always keep the water level at the recommended level. Fill theTank with enough
water so that the Pump is about 3/4 completely submerged, but not so much water
that the Tank overflows.
20.
21.
Avoid splashing water on the motor, power Switch, power cord, or any other
electrical component. Make sure to stand on a dry, insulated surface such as a
rubber mat while using the Tile Saw.
To avoid accidental injury,always wear heavy duty work gloves when changing
the Saw blade. Before using the Tile Saw, make sure the Saw Blade is properly
mounted on the Saw Spindle. Make sure the Saw Blade is balanced, and is not
cracked or bent.
SKU 92386
for technical questions, please call 1-800-444-3353.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
22.
23.
The Saw blade will become hot while cutting. Allow the Saw Blade to com-
pletely cool before handling.
Allow the Saw blade to spin up to full speed before feeding a workpiece into
it. When turning off the Tile Saw, allow the Saw Blade to spin down and stop on its
own. Do not press against the Saw Blade to stop it.
24.
25.
26.
27.
28.
Do not force the workpiece into the Saw blade when cutting. Apply moder-ate
pressure, allowing the Saw Blade to cut without being forced.
Turn off the Tile Saw and allow the Saw blade to stop on its own if the Saw
blade is to be backed out of an uncompleted cut.
Never attempt to remove material stuck in the moving parts of the Tile Saw
while it is plugged in and running.
When cutting a large workpiece make sure its entire length is properly sup-
ported. If necessary, use a roller stand (not included) with larger work pieces.
Never stand on the Tile Saw. Serious injury could result if the Tile Saw is tipped
or if the rotating Saw Blade is accidently contacted.
29.
30.
Industrial applications must follow OSHA requirements.
for your safety: In extreme working conditions, sensors in the Tile Saw will
automatically switch off the motor to prevent overheating. In this event, turn
the Power Switch to its “OFF” position. Wait five minutes or until the Motor has
cooled. Making sure your hands are dry, depress the Circuit Breaker. Then, turn
the Power Switch to its “ON” position to resume cutting. NeVer attempt to dis-
able the circuit breaker.
31.
32.
Never attempt to cut more than one tile at a time.
Never attempt to cut freehand. Make sure the tile to be cut is pressed firmly
against the Rip Fence.
33.
Never cut pieces too small to be held securely against the rip fence with-
out leaving enough space for the hand to be a safe distance from the Saw
blade.
34.
35.
36.
make sure the tile to be cut off has sufficient room to move sideways. Failure
to do so may result in the tile binding against the Saw Blade.
make sure the Table and surrounding area are clear with the exception of the
tile to be cut.
Always turn off the Tile Saw and unplug it from its electrical outlet before
changing accessories or performing any inspection, maintenance, or clean-
ing procedures.
SKU 92386
for technical questions, please call 1-800-444-3353.
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
37.
WArNINg! Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities, contain chemicals known (to the State of California) to
cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are: lead from lead-based paints, crystalline silica from bricks and ce-
ment and other masonry products, arsenic and chromium from chemically treated
lumber. Your risk from these exposures varies, depending on how often you do this
type of work. To reduce your exposure to these chemicals: work in well ventilated
areas, and work with approved safety equipment such as those dust masks that
are specially designed to filter out microscopic particles.
(California Health & Safety Code § 25249.5, et seq.)
38.
39.
WArNINg! People with pacemakers should consult their physician(s) before using
this product. Operation of electrical equipment in close proximity to a heart pace-
maker could cause interference or failure of the pacemaker.
WArNINg! The warnings and cautions discussed in this manual cannot cover
all possible conditions and situations that may occur. It must be understood by the
operator that common sense and caution are factors which cannot be built into this
product, but must be supplied by the operator.
SAVe THeSe INSTrucTIONS
ASSembly INSTrucTIONS
NOTe: For additional information regarding the parts listed in the following pages, refer
to the Assembly Diagram on page 25.
1.
2.
WArNINg! Always make sure the Power Switch of theTile Saw is in its “Off”
position and the unit is unplugged from its electrical outlet prior to assembling the
unit, adding any accessories, or making any adjustments to the unit.
Unpack the Tile Saw, and with assistance, carefully lay the tool on its side on a flat,
level floor surface. (See figure D, next page.)
REV 12/06
SKU 92386
for technical questions, please call 1-800-444-3353.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
Pull out the Stand I (57) and Stand II (64), fully extending the Support Brackets
(58). (See figure e.)
4.
5.
With assistance, set the Tile Saw upright. (See figure f.)
The Adjusting Knob (59) is located at the bottom of Stand II (64). Turn the Adjust-
ing Knob clockwise or counterclockwise to keep the Tile Saw balanced on the floor.
(See figure f.)
6.
Attach the Handle I (38) to the Motor Bracket (111), using the Bolts (98), Spring
Washers (95), and Washers (94). (See figure g.)
bOTTOm VIeW
cArefully lAy TIle SAW
ON ITS SIDe.
fIgure D
SuppOrT brAcKeT
(58)
bOTTOm VIeW
STAND I
(57)
STAND II
(64)
fIgure e
SIDe VIeW
ADjuSTINg KNOb
STAND II
(59)
(64)
ADjuSTINg KNOb
(59)
fIgure f
TOp VIeW
HANDle I
(38)
mOTOr brAcKeT
(111)
bOlTS (98)
SprINg WASHerS (95)
WASHerS (94)
SKU 92386
for technical questions, please call 1-800-444-3353.
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Wheel Assembly
121
123
120
126
1.
The Wheels (126) are connected to the Stand II (64) using Bolts (120), Lock Nuts
(123) and Washers (121). (See Fig. 1, 2, 3.)
Stand II (64)
2.
Lift the saw stand with the front handle to move it. (as shown in figure 5)
reV 04/06
SKU 92386
for technical questions, please call 1-800-444-3353.
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
OperATINg INSTrucTIONS
Note: The Rail Stand (41) of the Tile Saw is held in place by the packaging during
shipment. Always tighten the butterfly Knob to lock the rail Stand prior to
performing maintenance or moving the Tile Saw to another location.
(See figure H.)
eND VIeW
rAIl STAND
(41)
buTTerfly KNOb
(42)
fIgure H
To Fill And Drain The Water Tray:
1.
2.
3.
Fill the Water Tray (67) with enough clean, cold water so that the Water Pump (7)
is about 3/4 submerged, but not so much water that the Water Tray overflows.
(See figure I, next page.)
NOTe: To prevent excessive wear on the Saw Blade (4), make sure to maintain a
continuous flow of water over the entire Saw Blade while cutting. Never cut anything
if the water flow is not continuous.
To drain the Water Tray (67), remove the Drain Plug (69) located at the bottom of
the Water Tray. Once drained, replace the Drain Plug. NOTe: You may also pull out
the Water Tray from the Tile Saw and pour out the water. (See figure I.)
reV 09/06
SKU 92386
for technical questions, please call 1-800-444-3353.
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
WATer pump
flOW cONTrOl KNOb (7)
DrAIN plug
(69)
WATer TrAy
(67)
fIgure I
To Make A Straight Cut:
1.
WArNINg! use safety equipment. Always wear eye protection. Wear
ANSI approved safety glasses under an ANSI approved full face safety shield and
non-skid safety shoes. Hearing and breathing protection must be used for appro-
priate conditions.
2.
3.
Loosen the Butterfly Knob (47) on the Angle Cutting Guide (46) and position the
Angle Cutting Guide at 90 degrees to the Scale Rail (49). Then, retighten the But-
terfly Knob (47) on the Angle Cutting Guide. (See figure j.)
To Adjust the width between the Angle Cutting Guide (46) and a cutting slot in the
Table (44), loosen the Butterfly Knob (47) on the Scale Rail (49). Move the Scale
Rail to the desired position. Then, retighten the Butterfly Knob on the Scale Rail.
(See figure j.)
4.
Position the tile against the Scale Rail (49) and Angle Cutting Guide (46).
(See figure j.)
pOSITION Of TIle
ScAle rAIl
TAble (44)
(49)
ANgle cuTTINg
buTTerfly KNOb (47)
guIDe
(46)
fIgure j
buTTerfly KNOb (47)
5.
Check to make sure the water level in the Water Tray (67) is at the proper level (the
Water Pump (7) should be about 3/4 submerged in water). Turn the Flow Control
Knob on the Water Pump (7) all the way down. Then close the Water Tray com-
pletely. (See figure I.)
SKU 92386
for technical questions, please call 1-800-444-3353.
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
6.
7.
Plug the Power Cord Plug (20) into the nearest 120 volt, grounded, electrical outlet,
making sure to form a “drip loop” with the Power Cord. (See figure D, page 9.)
Turn the Power Switch (37) to its “ON” position, and allow the Saw Blade (4) to
spin up to full speed. (See figure K.)
cIrcuIT breAKer
(32)
pOWer SWITcH
(37)
fIgure K
8.
Adjust the Flow Control Knob on the Water Pump (7) until the water reaches the
edge of the Saw Blade (4), just before the Saw Blade would contact the tile being
cut. Make sure the Water Pump is supplying a continuous flow of water to the Saw
Blade. (See figure I, page 15.)
TIle
HANDle I
(38)
TAble (44)
SAW blADe
(4)
fIgure l
9.
Hold the tile firmly against the Angle Cutting Guide and Scale Rail (49) with one
hand. Always keep fingers a safe distance away from the blade (4). With the
other hand, hold the Handle I (38) and slowly move the Saw Blade forward over
the tile. (See figure l.)
REV 12/06
SKU 92386
for technical questions, please call 1-800-444-3353.
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
10.
11.
Continue moving the Saw Blade (4) over the tile until the cut is completed.
(See figure K, page 16.)
Once the cut is completed, turn the Power Switch (37) to its “OFF” position and al-
low the Saw Blade (4) to stop on its own. Unplug the Power Cord from its electrical
outlet. Then, remove the cut tile and debris from the Table (44).
(See figure K, page 16 and figure l, page 16.)
12.
13.
NOTe: If the Motor of the Tile Saw stops suddenly while cutting, turn the Power
Switch (37) to its “OFF” position. Wait approximately 5 minutes. Reset the Circuit
Breaker by pushing in the button. Then, turn the Power Switch to its “ON” position
to resume cutting. (See figure K, page 16.)
Note:If the Pump should fail, first try clearing the Filter (7B) of debris and make sure
it is not plugged. If the Pump still does not operate properly, it must be replaced.
To Make A Miter Cut:
1.
Loosen the Butterfly Knob (47) on the Angle Cutting Guide (46) and position the
Angle Cutting Guide at the desired angle to the Scale Rail (49). Then, retighten
the Butterfly Knob (47) on the Angle Cutting Guide. (See figure m.)
2.
3.
NOTe: For a 45 degree cut, you may also use the 45° Angle Cutting Guide (65)
that is included as an accessory item. (See figure m.)
To cut the tile, follow the same procedure as outlined in the section “To Make A
Straight Cut” beginning on page 15 of this manual.
45° ANgle
cuTTINg guIDe
(65)
ScAle
rAIl
(49)
ANgle cuTTINg
guIDe
(46)
buTTerfly KNOb (47)
fIgure m
To Make A Bevel Cut;
1.
Loosen the Knob I (22) on each end of the Tile Saw. Tilt the Slide Rail (26) to the
desired angle as indicated on the Angle Scale (43). Then, retighten the two Knobs
I. (See figure N, next page.)
2.
To cut the tile, follow the same procedure as outlined in the section “To Make A
Straight Cut” beginning on page 15 of this manual.
REV 12/06
SKU 92386
for technical questions, please call 1-800-444-3353.
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
rIgHT eND
lefT eND
KNOb I
(22)
KNOb I
(22)
fIgure N
To Change The Saw Blade:
1.
2.
WArNINg! Make sure the Power Switch (37) of the Tile Saw is in its “OFF”
position and that the unit is unplugged from its electrical outlet before performing
this procedure.
Remove the Bolts (91), Spring Washers (89), and Washers (88) from the Blade
Guard (12). (See figure O.)
blADe guArD
(12)
bOlT (91)
bOlT (91)
SprINg WASHer (89)
WASHer (88)
SprINg WASHer (89)
WASHer (88)
fIgure O
3.
Carefully lift up and move the Blade Guard (12) aside to expose the Saw Blade
(4). (See figure p, next page.)
SKU 92386
for technical questions, please call 1-800-444-3353.
Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
blADe guArD
(12)
rOTATION ArrOW
OuTSIDe flANge (5)
SAW blADe
(4)
NuT (6)
fIgure p
4.
5.
cAuTION! When necessary, wear heavy duty gloves to avoid accidental
cuts to hands and fingers.
With one Wrench (70), hold the Motor Arbor firmly in place while, with the other
Wrench (71) provided, unscrew and remove the Nut (6). Next, remove the Outside
Flange (5). Then, remove the old Saw Blade (4).
(See figures p and Q.)
SAW blADe
(4)
INSIDe flANge (3)
(DO NOT remOVe)
WreNcH
(70)
WreNcH
(71)
fIgure Q
SKU 92386
for technical questions, please call 1-800-444-3353.
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
6.
7.
8.
9.
Install a new Saw Blade (4). Always use Diamond Saw blades with a 7” diam-
eter, 5/8” round arbor hole, and rated at 3550 rpm or greater.
(See figure p, previous page.)
ImpOrTANT: When installing a Saw blade (4), make sure the “ArrOW” de-
picted on the side of the Saw blade points in the same direction as that of the
blade guard (12). (See figure r.)
Once the Saw Blade (4) is installed, refasten the Outside Flange (5) and Nut (6).
Make sure to tighten the Nut fully before using the Tile Saw.
(See figure p, previous page.)
Carefully lower the Blade Guard (12) back into its original position. Then secure
the Blade Guard in place using the Bolts (91), Spring Washers (89), and Washers
(88). (See figure S.)
blADe guArD (12)
SAW blADe (4)
ArrOW
ArrOW
fIgure r
bOlT (91)
SprINg WASHer (89)
WASHer (88)
bOlT (91)
SprINg WASHer (89)
WASHer (88)
fIgure S
SKU 92386
for technical questions, please call 1-800-444-3353.
Page 20
Download from Www.Somanuals.com. All Manuals Search And Download.
INSpecTION, mAINTeNANce, AND cleANINg
1.
2.
WArNINg! Make sure the Power Switch (37) of the Tile Saw is in its “OFF”
position and that the unit is unplugged from its electrical outlet before performing
any inspection, maintenance, or cleaning procedures.
before each use, inspect the general condition of the Tile Saw. Check for loose
screws, misalignment or binding of moving parts, damaged electrical wiring, dam-
aged Hoses, and any other condition that may affect its safe operation. If abnormal
noise or vibration occurs, have the problem corrected before further use. Do not
use damaged equipment.
3.
before each use, inspect the Saw Blade (4). Using a dull Saw Blade will cause
excessive wear on the Motor, and will not produce a satisfactory cut. Replace with
a new Saw Blade when needed.
4.
5.
before each use, inspect the mounting Screws on all Safety Covers and the Arbor
Nut (6) on the Motor Arbor. If necessary, retighten all loose hardware.
After each use, immediately clean the Water Pump (7) to keep dried debris from
sticking to the Filter (7B) and Impeller which will obstruct the water flow. To clean
the Water Pump, remove the Outer Cover (7A). Remove the Filter (7B). Then,
remove the Inner Cover (7C) to expose the Impeller. Use a small brush and clean
water to remove any debris on the Filter and Impeller. If necessary, replace the old
Filter with a new Filter. When finished, replace the Inner Cover, Filter, and Outer
Cover. (See Assy. Diagram.)
6.
7.
If the Water pump (7) should fail, first try cleaning the Filter (7B) and Impeller of
debris to make sure they are not plugged (see Step #5 above). If theWater Pump still
does not operate properly, the Pump must be replaced. (See Assy. Diagram.)
To replace theWater pump (7), remove theWaterTray (67). Locate the Pump Plug
Cover (118) on the inner left side of the Frame. Unscrew and remove the Knob 119,
Spring Washer (95), Washer (102), and Lock Nut (107) from the Pump Plug Cover.
Remove the Pump Plug Cover to expose the Pump Cable (117). Disconnect the
Pump Cable from theWater Pump. Next, disconnect the Pump Connector (115) from
the Water Pump. Then, remove the old Water Pump. Install the new Water Pump,
following the previously mentioned Steps in reverse order. (See Assy. Diagram.)
8.
9.
To clean the exterior parts: Use only a clean cloth and mild detergent to clean
the body of the Tile Saw. Use a vacuum or compressed air to clean the Motor (1)
ventilation slots. Do not immerse any electrical part of the tool in liquid.
When storing, always completely empty the Tile Saw of water. Frost will damage
the Pump if the unit contains water. Store the Tile Saw indoors in a dry, frost-free
room.
SKU 92386
for technical questions, please call 1-800-444-3353.
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
10.
cAuTION! All maintenance,service,or repairs not listed in Steps 2 through
9 in this section should only be performed by a qualified service technician.
pleASe reAD THe fOllOWINg cArefully
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST
AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY.
NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION
OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO
MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO
REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR
DISTRIBUTOREXPRESSLYSTATESTHATALLREPAIRSANDPARTSREPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSEDTECHNICIANS, AND NOT
BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF
HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT
PARTS THERETO.
SKU 92386
for technical questions, please call 1-800-444-3353.
Page 22
Download from Www.Somanuals.com. All Manuals Search And Download.
pArTS lIST
part
1
Description
part
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
Description
Motor
Circuit Breaker
2
Motor Cover
Inside Flange
Saw Blade
Capacitor Fixture I
Capacitor
3
4
Switch Box
5
Outside Flange
Nut
Capacitor Spacer
Power Switch
Handle I
6
7
Water Pump
Water Tube Cover
Flap Holder
8
Handle Grip
9
Spacer (Right)
Rail Stand (Right)
Butterfly Knob
Angle Scale
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Flap
Thee Way Connector
Blade Guard
Water Pipe Connector
Motor Support
Cable lock
Table
Water Tube Connector
Angle Cutting Guide
Butterfly Knob
Angle Rule Cushion
Scale Rail
Bearings Adjuster
Bearing Bracket
Bearings Axle
Bearing
Position Bar
Power Cable
Water Tube Holder
Knob I
Scale
Rail Stand
Position Bar Holder
Standing Frame
Scale Arm
Angle Scale
Rail Stand (Left)
Spacer (Left)
Slide Rail
Handle II
Stand I
Cable Lock
Support Bracket
Adjusting knob
Adjusting Slot
Adjusting Block
Adjusting Pin
Flat Nut
Rail Stand Support
Rail Stand Spacer
Switch Cover
* pump consists of: Outer cover (7A), filter (7b), Inner cover (7c), motor (7D).
reV 04/06
SKU 92386
for technical questions, please call 1-800-444-3353.
Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
pArTS lIST cONT.
part
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
Description
part
96
Description
Foot Pad
Stand II
45° Angle Cutting Guide
Pipe
Bolt
97
Bolt
98
Bolt
99
Bolt
Water Tray
Pump Fixture
Drain Plug
Wrench
Wrench
Nut
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
Bolt
Washer
Washer
Flat Nut
Lock Nut
Bolt
Washer
Spring Washer
Washer
Washer
Bolt
Nut
Lock Nut
Washer
Bolt
Control Box Seal
Motor Bracket
Handle Shell
Handle Pad I
Handle Pad II
Pump Connector
O - Ring
Bolt
Bolt
Bolt
Bolt
Bolt
Bolt
Square Bolt
Lock Washer
Screw
Pump Cable
Pump Plug Cover
Knob
Counter Bolt
Washer
Spring Washer
Bolt
Bolt
Washer
Wheel Fixture
Lock Nut
Bolt
Bolt
Bolt
Washer
Nut
Wheel
Washer
Spring Washer
Lock Nut
reV 04/06
SKU 92386
for technical questions, please call 1-800-444-3353.
Page 24
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSembly DIAgrAm
NOTe:
Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
reV 04/06
SKU 92386
for technical questions, please call 1-800-444-3353.
Page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
|