20” Push/Pull
steel lawn RolleR
Model 98383
asseMbly, oPeRating, and Maintenance
instRuctions
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
distributed exclusively by harbor Freight tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
saVe this Manual.
©
®
Copyright 2008 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Keep hands and feet away from Roll-
er Barrel when using. Never stand in
the direct path of the Roller.
supplied by the operator.
saVe these
instRuctions.
6. Do not Use on wet, or damp lawn
or dirt. Grass, mud and debris can
build up at Roller Barrel Axle and/or
against the Scraper Plate (6) causing
the Barrel to become hard to push.
7. Keep Children Away and never al-
low them to play with this Steel Lawn
Roller. All visitors should be kept at a
distance from work area. Keep pets
out of the work area.
sPeciFications
Roller Barrel: Formed, Round
Steel.
Upper and Lower Handle:
Formed Steel.
Construction
8. When servicing use only identical
replacement parts.
All Hardware: Carbon Steel.
Drain Plug: Hard Rubber.
Overall Height
Net Weight
42-1/2” High
9. When not in use, store this Steel
Lawn Roller Indoors.
23.40 LB (Empty)
10. Maintain Steel Lawn Roller with care.
Keep Roller Barrel clean for best per-
formance. Inspect Steel Lawn Roller
periodically, and if damaged, have
it repaired by an authorized service
facility. Keep handles dry, clean, and
free from oil and grease.
unPacking
When unpacking, check to make sure
that the item is intact and undamaged. If
any parts are missing or broken, please
call Harbor Freight Tools at the number
shown on the cover of this manual as soon
as possible.
11. Do not use this Steel Lawn Roller for
other than intended use.
note: For additional information regarding
the parts listed in the following pages,
refer to the Assembly Diagram near
the end of this manual.
12. Maintain labels and nameplates on
the appliance. These carry important
safety information. If unreadable or
missing, contact Harbor Freight Tools
for a replacement.
asseMbly
13. The warnings, precautions, and
instructions discussed in this
1. Mount the two Lower Handles (7) to
the axle of the Roller Barrel (1) and
secure each side with a Cap Nut (3).
instruction manual cannot cover all
possible conditions and situations
that may occur. It must be understood
by the operator that common sense
and caution are factors which cannot
be built into this product, but must be
2. Mount the Top Handle (10) to the
Lower Handles (7) using the Bolts (8)
and the Lock-Washer Nuts (9). Refer
to “Assembly Diagram” on page 6 for
SKU 98383
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
correct insertion direction for Bolts
(8).
subheadings therein before set
up or use of this product.
3. Attach the Scraper Plate (6) through
the existing holes in each of the
Lower Handles (7) using the Nuts (5)
and the Bolts (4).
1. Before operating the Steel Lawn
Roller, put on ANSI-approved safety
goggles, steel toe shoes and other
safety gear. Safety goggles and
other safety gear are sold separately.
Figure 1
2. Roll the Steel Lawn Roller to the area
to be compacted.
3. Use the Steel Lawn Roller as you
would if you were mowing a lawn.
Roll one direction until all areas are
rolled, then roll the other direction till
area is completely rolled again.
Drain Plug
Drain
4. If it is necessary to wash or clean
debris from the Roller Barrel before
you are finished using it, be sure to
dry the surface with a towel or absor-
bent cloth to prevent a quick build up
of added debris.
4. Add weight to the Steel Lawn Roller
by standing the empty Roller Barrel
on it’s side with the Drain Hole up.
Remove the Drain Plug (2), then us-
ing a funnel (not supplied) carefully
pour water or sand into the opening
until full. (Sand would give maximum
weight.) See Figure 1.
5. When completely finished with your
project, wash off the Steel Lawn
Roller with a hose and soft rag or
brush and let stand until completely
dry before storing. Store in garage or
shed away from children.
Maintenance and
seRVicing
to PReVent seRious injuRy FRoM
tool FailuRe:
5. Using two people for added safety,
carefully lay the Steel Lawn Roller
onto the ground.
Do not use damaged equipment. If any-
thing abnormal is noticed, or occurs while
using, have the problem corrected before
further use.
oPeRating instRuctions
Read the entiRe
iMPoRtant saFety
inFoRMation section at the
beginning of this manual
including all text under
Procedures not
specifically explained in this
manual must be performed only
by a qualified technician.
SKU 98383
For technical questions, please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
cleaning, Maintenance, and
lubrication
PaRts list
Discription
Part #
q’ty
1
1
2
3
4
5
6
7
8
9
10
Roller Barrel
Drain Plug
1. Use a small amount of axle grease to
lubricate axles periodically.
1
Cap Nut
2
2. Before use, check for cracks in Top
and Lower Handles and/or in Roller
Barrel. If any damage is found, have
the problem repaired before using.
Bolt (M6x35)
Nut (M6)
2
2
Scraper Plate
Lower Handle
Bolt (M5 x 30)
Lock-Washer Nut (M5)
Top Handle
2
2
3. After using, wipe away all dirt and
debris with clean, damp (with water)
cloth, then dry and store inside away
from children.
2
2
1
4. Never put lubricants over the Roller
Barrel.
note: If the Steel Lawn Roller has been
filled with water and is to be stored
for an extended period of time, emp-
ty the water by removing the Drain
Plug and allowing the water to drain
completely. Dry sand may remain
inside the Roller Barrel while stored.
Please Read the Follow-
ing caReFully
THE MANUFACTURER AND/OR DISTRIBUTOR
HAS PROvIDED THE PARTS LIST AND ASSEMBLy
DIAGRAM IN THIS MANUAL AS A REFERENCE
TOOL ONLy. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANy REPRESENTATION
OR WARRANTy OF ANy KIND TO THE BUyER
THAT HE OR SHE IS qUALIFIED TO MAKE ANy
REPAIRS TO THE PRODUCT, OR THAT HE OR SHE
IS qUALIFIED TO REPLACE ANy PARTS OF THE
PRODUCT. IN FACT, THE MANUFACTURER AND/
OR DISTRIBUTOR ExPRESSLy STATES THAT ALL
REPAIRS AND PARTS REPLACEMENTS SHOULD
BE UNDERTAKEN By CERTIFIED AND LICENSED
TECHNICIANS, AND NOT By THE BUyER. THE
BUyERASSUMESALLRISKANDLIABILITyARISING
OUT OF HIS OR HER REPAIRS TO THE ORIGINAL
PRODUCT OR REPLACEMENT PARTS THERETO,
OR ARISING OUT OF HIS OR HER INSTALLATION
OF REPLACEMENT PARTS THERETO.
SKU 98383
For technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
asseMbly diagRaM
Record Product’s serial number here:
note: If product has no serial number, record month and year of purchase instead.
note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
SKU 98383
For technical questions, please call 1-800-444-3353.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
|