TREE PRUNER
09712
ASSEMBLY AND OPERATING INSTRUCTIONS
Copyright© 2004 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight
Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual
product may differ slightly from the product described herein. Tools required for assembly and service may not
be included.
For technical questions and replacement parts, please call 1-800-444-3353.
Specifications
Blade Dimensions
Jaw Dimensions
Throat Depth
0.041” Thick x 12” Long / 6 Teeth Per Inch
1-1/2” Diameter Lopper Cutting Capacity
2-1/4”
Rope Length
110-1/2”
Pole Dimensions
Tool Weight
53-5/8” c 1-3/32”
4.52 Lbs.
Save This Manual
You will need the manual for the safety warnings and precautions, assembly instructions, operating and main-
tenance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice number on
the inside of the front cover. Keep the manual and invoice in a safe and dry place for future reference.
Safety Warnings and Precautions
WARNING: When using tool, basic safety precautions should always be followed to reduce the risk of
personal injury and damage to equipment.
Read all instructions before using this tool!
Revised Manual 09k
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover
all possible conditions and situations that may occur. It must be understood by the operator that com-
mon sense and caution are factors which cannot be built into this product, but must be supplied by the
operator.
Assembly: The only assembly required is mounting the Saw Blade (#5) to the Base (#1). Line up the tab on the
blade so that it fits in the small hole on the base making sure that the larger hole on the blade lines up with the
larger hole on the Base (#1). Insert the Bolt (#19) and a Washer (#17) through the Saw Blade (#5) and the
Base (#1). Secure it with the Wing Nut (#20). See the Assembly Drawing on page 4 and FIGURE 1 below.
Operation
1. On the Handle, twist the Lock Ring (#10) to loosen it and extend the telescoping handle to the desired length.
Tighten the Lock Ring (#10).
Note: After telescoping the Handle and before cutting, take up the slack in the rope and secure it around the
Handle, out of your way.
2. When using the Saw Blade (#5), make sure the blade is straight and not bending when cutting. Apply mimimal
pressure allowing the blade to do the work.
3. When using the Pruner Blade (#2), position the end of the handle against your hip and hold the Handle with
one hand as far up the Handle as possible. Once you situate the branch to be cut in the jaws (see FIGURE 1),
pull on the rope to clamp the Pruner Blade (#2) shut, cutting the branch.
FIGURE 1
Pruner Blade (#2)
Saw Blade (#5)
Bolt (#19
Insert
Branch
(Jaws)
Base (#1)
Unpacking
When unpacking, check to make sure the parts listed on page 4 are included. If any parts are missing or bro-
ken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDEDTHE PARTS DIAGRAM INTHIS
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBU-
TOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT
HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE
IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR EXPRESSLY STATESTHAT ALL REPAIRS AND PARTS REPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER
REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
NOTE: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
SKU 09712
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List and Assembly Drawing
Part No.
Description
Base
Qty Part No.
Description
Nylon Nut
Qty
1
1
2
1
1
1
1
1
1
1
2
1
1
1
1
1
1
15
16
17
18
19
20
21
22
23
24
25
26
27
Pruner Blade
Pole Socket
Pulling Base
Saw Blade
Pulley Base (A)
Pulley Base (B)
Pulley
Screw
Washer
Nylon Nut
Mounting Bolt
Wing Nut
Screw
Nut
1
3
2
4
1
5
1
6
1
7
2
8
2
9
Grip
Bolt
2
10
11
12
13
14
Lock Ring
Spring
Bolt
1
Bolt
1
Center Screw
Spring Washer
Washer
Bolt
2
Bolt
2
SKU 09712
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
|