Harbor Freight Tools Patio Furniture 3551 User Manual

arbor press  
03551  
03552  
Model  
set up and operating instructions  
Visit our website at: http://www.harborfreight.com  
read this material before using this product.  
Failure to do so can result in serious injury.  
saVe this Manual.  
©
®
Copyright 1997 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork  
contained herein may be reproduced in any shape or form without the express written consent of  
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing  
improvements, actual product may differ slightly from the product described herein. Tools required for  
assembly and service may not be included.  
For technical questions or replacement parts, please call 1-800-444-3353.  
Manual revised 10i  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11. Maintain tools With care. Keep  
tools sharp and clean for better and  
safer performance. Follow instructions  
for lubricating and changing accessories.  
Inspect tool cords periodically and, if  
damaged, have them repaired by an  
authorized technician. The handles must  
be kept clean, dry, and free from oil and  
grease at all times.  
damaged should be properly repaired  
or replaced by a qualified technician. Do  
not use the tool if any switch does not  
turn on and off properly.  
18. guard against electric shocK.  
Prevent body contact with grounded  
surfaces such as pipes, radiators,  
ranges, and refrigerator enclosures.  
19. replaceMent parts and  
accessories. When servicing, use  
only identical replacement parts. Use of  
any other parts will void the warranty.  
Only use accessories intended for use  
with this tool. Approved accessories are  
available from Harbor Freight Tools.  
12. disconnect poWer. Unplug when  
not in use, before servicing, and when  
changing accessories.  
13. reMoVe adJusting Keys and  
Wrenches. Make it a habit to check  
that keys and adjusting wrenches are  
removed from the tool or machine work  
surface before plugging it in.  
20. do not operate tool iF under  
the inFluence oF alcohol  
or drugs. Read warning labels  
on prescriptions to determine if your  
judgment or reflexes are impaired while  
taking drugs. If there is any doubt, do not  
operate the tool.  
14. aVoid unintentional starting.  
Be sure the switch is in the OFF position  
when not in use and before plugging in.  
Do not carry any tool with your finger on  
the trigger, whether it is plugged in or  
not.  
unpacKing  
15. outdoor eXtensions cords.  
When the equipment is operated  
outdoors, use only extension cords  
intended for outside use. See chart  
under “Extension Cords" for the proper  
AWG rating depending on the length of  
the cord(s) being used.  
If any parts are missing or broken,  
please call Harbor Freight Tools at the number  
on the cover of this manual.  
part  
1
N/A  
6
description  
Body  
Handle Assembly  
Plate  
Rack  
Qty  
1
1
1
1
16. stay alert. Watch what you are  
doing; use common sense. Do not  
operate any tool when you are tired.  
10  
17. checK daMaged parts. Before  
using any tool, any part that appears  
damaged should be carefully checked  
to determine that it will operate properly  
and perform its intended function. Check  
for alignment and binding of moving  
parts; any broken parts or mounting  
fixtures; and any other condition that may  
affect proper operation. Any part that is  
SKU 03551 03552 For technical questions, please call 1-800-444-3353.  
Page 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
arbor press assembly  
asseMbly  
Mounting the body to your  
Workbench  
Plate (#6)  
Spring Pin (#7)  
(not shown)  
1. Select a place on your workbench to  
mount the Arbor Press.  
Body (#1)  
2. Purchase hardware to mount your Arbor  
Press to your workbench. Bolt length  
will be the thickness of your workbench  
plus 2-1/2” of length for the Arbor Press  
BODY (#1).  
Figure 2 -- Installing the Plate  
Body (#1)  
1. Place the PLATE (#6) onto the Base of  
the BODY (#1) as shown in Figure 2.  
Insert the SPRING PIN (#7) into the hole  
in the BODY.  
Mounting Hole  
(not shown)  
Mounting Hole  
Rack Teeth  
Rack (#10)  
Figure 1 -- Location of Mounting Holes  
3. Use the two mounting holes in the BODY  
of the Arbor Press as a template as  
shown in Figure 1. Mark and Drill holes  
in your workbench.  
Body (#1)  
Cover (#8)  
4. Place the BODY over the holes in the  
workbench and insert the bolts through  
the holes. Thread on the nuts and  
tighten.  
Figure 3 -- Installing the Rack  
2.  
Insert the RACK (#10) down through the top  
of the BODY as shown in Figure 3. Make  
sure the teeth of the RACK are towards the  
rear of the BODY as shown in the Figure.  
SKU 03551 03552 For technical questions, please call 1-800-444-3353.  
Page 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3.  
Unwrap the Handle Assembly and discard  
the protective padding.  
7.  
Your Arbor Press is ready for use.  
Handle Assembly  
Body (#1)  
Figure 4 -- Installing the Handle Assembly  
4.  
5.  
Insert the GEAR (#14) section of the Handle  
Assembly into the side of the Arbor Press as  
shown in Figure 4. The GEAR will only fit  
into the side shown in the Figure.  
You may have to rotate the Handle Assembly  
slightly to get the teeth of the GEAR to mesh  
with the teeth of the RACK.  
Rack (#10)  
Ring (#5)  
Handle Assembly  
Figure 5 -- Attaching the Ring  
6.  
Slide the RING (#5) onto the protruding end  
of the GEAR as shown in Figure 5. Tighten  
the SCREW (#4) on the RING to secure the  
GEAR and Handle Assembly.  
SKU 03551 03552 For technical questions, please call 1-800-444-3353.  
Page 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
using the arbor press  
operation  
adjusting the handle assembly  
1. Determine if you will need a moderate or  
large amount of leverage for the job.  
Rack (#10)  
Lock Pin (#11)  
Shaft (#15)  
Shaft (#15)  
Plate (#6)  
Figure 7 -- Raising the Rack  
Figure 6 -- Adjusting the Shaft  
1. Raise the RACK (#10) up by turning the  
Handle Assembly as shown in Figure 7.  
2. Loosen the LOCK PIN (#11) by turning it  
as shown in Figure 6. This will allow you  
to adjust the length of the SHAFT (#15).  
2. Turn the PLATE (#6) until the appropriate  
width opening is centered under the  
RACK. The appropriate width depends  
upon what you are using the press for.  
If you do not want an opening beneath  
the RACK, rotate the PLATE until one  
of the four solid parts of the PLATE is  
underneath the RACK.  
3. Adjust the length of the SHAFT to  
suit your needs. If a large amount of  
leverage is needed for your press job,  
lock the SHAFT in the extended position.  
If a moderate amount of leverage is  
needed, position the SHAFT in the  
middle of the GEAR.  
3. Place the part you need to press onto  
the PLATE.  
4. Tighten the LOCK PIN to secure the  
Handle Assembly.  
4. Turn the Handle Assembly to lower the  
RACK until the top of the RACK contacts  
the press part.  
The following Steps show the SHAFT in  
the extended position.  
5. Place downward pressure on the Handle  
Assembly to press the part as needed.  
6. Release pressure on the Handle  
Assembly and raise the RACK to remove  
the part.  
SKU 03551 03552 For technical questions, please call 1-800-444-3353.  
Page 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
parts list and asseMbly diagraM  
part  
description Qty  
part  
7
8
description Qty  
part  
13  
14  
15  
16  
description Qty  
1
2
3
4
5
6
Body  
Bolt  
1
8
6
1
1
1
Spring Pin  
Cover  
1
1
1
1
1
1
Screw  
Gear  
1
1
1
2
Nut  
9
Washer  
Rack  
Lock Pin  
Pin  
Shaft  
Handle  
Screw  
Ring  
Plate  
10  
11  
12  
SKU 03551 03552 For technical questions, please call 1-800-444-3353.  
Page 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
liMited 90 day Warranty  
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and  
durability standards, and warrants to the original purchaser that this product is free from defects  
in materials and workmanship for the period of 90 days from the date of purchase. This warranty  
does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents,  
repairs or alterations outside our facilities, criminal activity, improper installation, normal wear  
and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons  
or property, or for incidental, contingent, special or consequential damages arising from the use  
of our product. Some states do not allow the exclusion or limitation of incidental or consequential  
damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS  
ExPRESSLY IN LIEU OF ALL OTHER WARRANTIES, ExPRESS OR IMPLIED, INCLUDING  
THE WARRANTIES OF MERCHANTABILITY AND FITNESS.  
To take advantage of this warranty, the product or part must be returned to us with  
transportation charges prepaid. Proof of purchase date and an explanation of the complaint must  
accompany the merchandise. If our inspection verifies the defect, we will either repair or replace  
the product at our election or we may elect to refund the purchase price if we cannot readily and  
quickly provide you with a replacement. We will return repaired products at our expense, but if  
we determine there is no defect, or that the defect resulted from causes not within the scope of  
our warranty, then you must bear the cost of returning the product.  
This warranty gives you specific legal rights and you may also have other rights which vary  
from state to state.  
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353  
SKU 03551 03552 For technical questions, please call 1-800-444-3353.  
Page 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Haier Freezer DW 150W200 User Manual
Haier Refrigerator BCF27 User Manual
Hamilton Beach Mixer 840148500 User Manual
HANNspree Flat Panel Television HANNSrobby User Manual
Hasselblad Camera Lens HC 28 80 User Manual
Havis Shields Automobile Parts KK K9 F14 K PT User Manual
Healthrider Treadmill HRTL19990 User Manual
HP Hewlett Packard Laptop 2540P User Manual
Hubbell Switch LXi 1800 User Manual
Hunter Fan Outdoor Ceiling Fan 42650 02 User Manual